Samsung | PM32F-BC | Samsung PM32F-BC Quick start guide

Reverse Side
Quick Setup Guide
TOUCH OUT
SCREEN
TOUCH OUT
PC
03
• Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
HDMI2
HDMI1
AUDIO
IN
RS232C
OUT
AUDIO
OUT
06
07
MagicInfo Software DVD
Power cord
11
08DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
PC IN: Use the (dedicated) D-SUB - DVI cable (or D-SUB cable with D-SUB to DVI
adapter) when connecting a PC.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
09Connects to a source device using a DP cable.
10 Connects to another product using a daisy chain (DP port) cable.
11 Connects to MDC using a LAN cable.
Issues
Solutions
Check the cable connection between the product
and PC, and ensure the connection is secure.
The screen is too bright.
The screen is too dark.
Adjust Brightness and Contrast.
No Signal is displayed on the
screen.
Check that the product is connected correctly with
a cable.
Screen color is inconsistent.
Go to Picture and adjust the Color Space settings.
White does not really look
white.
Go to Picture and adjust the White Balance settings.
There is no sound.
Check the connection of the audio cable or adjust
the volume.
-
Not Optimum Mode is
displayed.
Remote Control
RS232C(IN) adapter
This message is displayed when a signal from the
graphics card exceeds the product’s maximum
resolution and frequency.
Refer to the Standard Signal Mode Table and set
the maximum resolution and frequency according
to the product specifications.
Ring-type holder* (4 pieces)
10
Solutions
+
+
Screw (M3L8, 1 piece)
09
The screen keeps switching
on and off.
Check that the device connected to the product is
powered on.
USB cable
RJ45
Issues
-
Batteries (Not available in some locations)
08
DAISY CHAIN
Troubleshooting Guide
Contact the vendor where you purchased the product if any components are missing.
Warranty card (Not available in some
locations)
05
DP IN
BN68-08272S-01
Checking the Components
Quick Setup Guide
04
01 Connect to a USB port on the product to use the touch function.
02Connect to a PC to use the touch function.
03Connect to a USB memory device.
04Connects to MDC using an RS232C adapter.
05Receives sound from a source device via an audio cable.
06Connects to the audio of a source device.
07 Connects to a source device using an HDMI cable.
• The colour and the appearance may differ depending on the product, and the specifications are subject
to change without prior notice to improve the performance.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
RS232C
IN
USB2
(0.5A)
USB1
(1.0A)
PM32F-BC
DVI/PC/
MAGICINFO IN
02
01
USB cover
* Use the provided Ring-type holder (HOLDER-WALL RING, BN61-14912A) to install the PM32F-BC model on the wall.
The images on the screen
look distorted.
Check the cable connection to the product.
The screen is not clear.
The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension cable,
etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears unstable
and shaky.
There are shadows or ghost
images left on the screen.
Check that the resolution and frequency of the
PC and graphics card are set within a range
compatible with the product. Then, change the
screen settings if required by referring to the
Additional Information on the product menu and
the Standard Signal Mode Table.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the
maximum level, adjust the volume on your PC
sound card or software program.
The remote control does not
work.
Make sure that the batteries are correctly in place
(+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
Connecting and Using a Source Device
Connecting to a PC
Specifications
Connecting to an Audio System
Model Name
Panel
AUDIO OUT
DVI / PC / MAGICINFO IN
AUDIO IN
Connecting the LAN Cable
DVI / PC / MAGICINFO IN
80.1 cm
Display area
698.4 mm (H) x 392.85 mm (V)
10 W + 10 W
Power Supply
AC 100 to 240 VAC (+/- 10%), 60 / 50 Hz ± 3 Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Operating
Temperature: 0 ˚C - 40 ˚C (32 ˚F - 104 ˚F), With PIM: 10 ˚C - 40 ˚C (50 ˚F - 104 ˚F)
Humidity: 10% - 80%, non-condensing
Storage
Temperature: -20 ˚C - 45 ˚C (-4 ˚F - 113 ˚F)
Humidity: 5% - 95%, non-condensing
• This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
• For detailed device specifications, visit the Samsung Electronics website.
• The PVC Free (except for accessory cables) logo is the self-declared trademark of Samsung.
* Accessory cables: signal cables and power cords
Use Cat7(*STP Type) cable for the connection.
* Shielded Twist Pair
AUDIO IN
PM32F-BC
Size
Audio Output
Environmental
considerations
RJ45
Ⓡ
Connecting to MDC
(For India Only)
This product is RoHS compliant.
For more information on safe disposal and recycling visit
our website www.samsung.com/in or contact our Helpline
numbers - 1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
RS232C IN
HDMI1, HDMI2
Warning! Important Safety Instructions
RS232C OUT
RS232C IN
AUDIO IN
(Please read the appropriate section that corresponds to the marking on your Samsung product before attempting to install the product.)
RS232C OUT
RS232C IN
RS232C OUT
HDMI1, HDMI2
RJ45
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
• If your equipment uses an AC adapter:
‒ Only use the AC adapter with your product by Samsung.
‒ Do not use the power cord with other products.
• Do not install this equipment in a confined space such as a case or similar.
• The slots and openings in the cabinet and in the back or bottom are provided for necessary
HUB
DP IN
ventilation. The slots and openings must never be blocked or covered.
• The product should be located away from heat sources such as radiators, heat registers, or
other products that produce heat.
This symbol indicates that high voltage is present inside. It is dangerous to
make any kind of contact with any internal part of this product.
This symbol alerts you that important literature concerning operation and
maintenance has been included with this product.
• Do not place a water containing vessel (vases etc.) on this apparatus, as this can result in a risk
of fire or electric shock. (Apparatus shall not be exposed to dripping or splashing)
• The apparatus must be connected to an earthed MAINS socket-outlet (Class l Equipment only).
Or Use only a properly grounded plug and receptacle (Class l Equipment only).
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains
socket, therefore the mains plug shall be readily operable.
• As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power
source even if you turn off this unit by POWER.
This product is RoHS compliant.
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household
waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and
recycle them responsibly to promote the sustainable reuse of material resources.
For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers -1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
Connecting an External Monitor
DAISY CHAIN
RJ45
Contact SAMSUNG WORLD WIDE
Connecting to a Video Device
HDMI1, HDMI2
RS232C OUT
RS232C IN
RS232C OUT
RS232C IN
AUDIO IN
RS232C OUT
• For details on how to use the MDC programme, refer to Help after installing
the programme.
• The MDC programme is available on the website.
HDMI1, HDMI2
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Tel. 1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
www.samsung.com/in/support
Download PDF