Samsung | HW-M360 | Samsung Soundbar 200W 2.1Ch HW-M360 Quick start guide

USER MANUAL
HW-M360
SAFETY INFORMATION
SAFETY WARNINGS
WARNING
•• To reduce the risk of fire or electric shock, do
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
not expose this appliance to rain or moisture.
NOT REMOVE THE COVER (OR BACK).
CAUTION
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
•• TO PREVENT ELECTRIC SHOCK, MATCH WIDE
PERSONNEL.
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
•• This apparatus shall always be connected to a
CAUTION
AC outlet with a protective grounding
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
connection.
This symbol indicates that high voltage
is present inside. It is dangerous to make
any kind of contact with any internal
part of this product.
This symbol indicates that this product
has included important literature
concerning operation and maintenance.
•• To disconnect the apparatus from the mains,
the plug must be pulled out from the mains
socket, therefore the mains plug shall be
readily operable.
•• Do not expose this apparatus to dripping or
splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
•• To turn this apparatus off completely, you
Class II product : This symbol indicates
must pull the power plug out of the wall
that it does not require a safety
socket. Consequently, the power plug must
connection to electrical earth (ground).
be easily and readily accessible at all times.
AC voltage : This symbol indicates that
the rated voltage marked with the
symbol is AC voltage.
DC voltage : This symbol indicates that
the rated voltage marked with the
symbol is DC voltage.
Caution, Consult instructions for use :
This symbol instructs the user to consult
the user manual for further safety
related information.
ENG - ii
PRECAUTIONS
5. The battery used with this product contains
chemicals that are harmful to the
environment. Do not dispose of the battery
1. Ensure that the AC power supply in your
in the general household trash. Do not
house complies with the power
expose the battery to excess heat, direct
requirements listed on the identification
sunlight, or fire. Do not short circuit,
sticker located on the back of your product.
disassemble, or overheat the battery.
Install your product horizontally, on a
Danger of explosion if the battery is replaced
suitable base (furniture), with enough space
incorrectly. Replace only with the same or
around it for ventilation (7~10 cm). Make sure
equivalent type.
the ventilation slots are not covered. Do not
place the unit on amplifiers or other
is designed for continuous use. To fully turn
ABOUT THIS MANUAL
off the unit, disconnect the AC plug from the
The user manual has two parts: this simple paper
equipment which may become hot. This unit
wall outlet. Unplug the unit if you intend to
USER MANUAL and a detailed FULL MANUAL you
leave it unused for a long period of time.
can download.
2. During thunderstorms, disconnect the AC
plug from the wall outlet. Voltage peaks due
to lightning could damage the unit.
3. Do not expose the unit to direct sunlight or
other heat sources. This could lead to
overheating and cause the unit to
USER MANUAL
malfunction.
See this manual for safety instructions,
4. Protect the product from moisture (i.e.
product installation, components,
vases), and excess heat (e.g. a fireplace) or
connections, and product specifications.
equipment creating strong magnetic or
electric fields. Unplug the power cable from
the AC wall socket if the unit malfunctions.
Your product is not intended for industrial
use. It is for personal use only. Condensation
may occur if your product has been stored in
cold temperatures. If transporting the unit
during the winter, wait approximately
2 hours until the unit has reached room
temperature before using.
FULL MANUAL
You can access the customer support centre
by scanning the QR code. To see the manual on
your PC or mobile device, download the
manual in document format from the website.
(http://www.samsung.com/support)
Design and specifications are subject to change
without prior notice.
ENG - iii
CONTENTS
01
Checking the Components
2
Inserting Batteries before using the Remote Control (AA batteries X 2) -------------------------- 2
02
03
04
05
Product Overview
3
Front Panel / Right Side Panel of the Soundbar
-------------------------- 3
Bottom Panel of the Soundbar
-------------------------- 3
Connecting the Soundbar
Connecting Electrical Power
-------------------------- 4
Connecting the Soundbar to the Subwoofer
–– Automatic connection between the subwoofer and the Soundbar
–– Manually connecting the subwoofer if automatic connection fails
-------------------------- 5
-------------------------- 5
-------------------------- 6
Connecting to your TV
7
Method 1. Connecting with a Cable
–– Connecting using an Optical Cable
-------------------------- 7
-------------------------- 7
Method 2. Connecting Wirelessly
–– Connecting a TV via Bluetooth
-------------------------- 8
-------------------------- 8
Connecting an External Device
Connecting using an Optical or Analogue Audio (AUX) Cable
06
4
Connecting a USB
10
-------------------------- 10
11
Software Update
-------------------------- 11
ENG - iv
07
Connecting a Mobile Device
Connecting via Bluetooth
08
09
12
-------------------------- 12
Using the Remote Control
13
How to Use the Remote Control
-------------------------- 13
Adjusting the Soundbar volume with a TV remote control
-------------------------- 15
Installing the Wall Mount
16
Installation Precautions
-------------------------- 16
Wallmount Components
-------------------------- 16
Detaching the Soundbar from the Wall
-------------------------- 19
10Troubleshooting
20
11Licence
21
12
Open Source Licence Notice
21
13
Important Notes About Service
21
14
Specifications and Guide
22
Specifications
-------------------------- 22
ENG - v
01 CHECKING THE COMPONENTS
Bluetooth
POWER
Surround
SOUND
MODE
VOL
WOOFER
SOUNDBAR
Soundbar Main Unit
1
Subwoofer
Remote Control / Batteries
Optical Cable
Micro USB to
USB adapter Cable
3
Power Cord
(Subwoofer)
AC/DC Adapter
(Main Unit)
2
Connect the AC plug to the adapter
until you hear a “snapping” sound to
ensure they are securely fastened.
AC Plug
Do not detach the AC plug from the
(Depending on the country and
adapter (it will not be removed once it
model)
has been attached).
•• The power connection steps are labelled (1, 2, 3). For more information about power
connections, see page 4.
•• For Soundbar wall mounting components, see page 16.
•• Depending on the region, the AC plug may vary in appearance, or it may be supplied integrated with
the AC/DC adapter.
Inserting Batteries before using the Remote Control (AA batteries X 2)
Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries
(1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.
ENG - 2
02 PRODUCT OVERVIEW
Front Panel / Right Side Panel of the Soundbar
Right Side of the Soundbar
Position the product so
that the SAMSUNG logo
Volume
is located on the top.
Power
Display
Bottom Panel of the Soundbar
DIGITAL AUDIO IN
(OPTICAL)
USB (5V 0.5A)
AUX IN
DC 19V
DIGITAL AUDIO IN
(OPTICAL)
DC 19V
USB (5V 0.5A)
AUX IN
Source
Selects the source input mode. (D.IN / AUX / BT / USB)
•• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and
hold the
(Source) button for more than 5 seconds.
D.IN
Connect to the digital (optical) output of an external device.
USB
Connect a USB device here to play music files on the USB device through the Soundbar.
AUX
Connect to the Analogue output of an external device.
DC 19V
Connect the AC/DC power adapter. (Power Supply In)
ENG - 3
03 CONNECTING THE SOUNDBAR
Connecting Electrical Power
Use the power components (1, 2, 3) to connect the units to electrical outlets in the following order:
1.) Subwoofer  2.) Soundbar Main Unit. See the illustrations below.
•• For more information about the required electrical power and power consumption, refer to the
label attached to the product. (Label : Bottom of the Soundbar Main Unit)
2 AC Plug
3 AC/DC Adapter
1 Power Cord
DC 19V
(Power Jack)
POWER
ID SET
POWER
DC 19V
Rear of Subwoofer
DC 19V
Connecting
Electrical Power
Bottom of the
Soundbar Main Unit
ENG - 4
Connecting the Soundbar to the Subwoofer
When the subwoofer is connected, you can enjoy rich bass sound.
Automatic connection between the subwoofer and the Soundbar
When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the
subwoofer is automatically connected to the Soundbar.
•• When auto pairing is complete, the blue indicators at the top of the subwoofer turn on.
LED Indicator Lights on the Top of Subwoofer
LED
Status
On
Description
Successfully connected
(normal operation)
Resolution
Check if the power cable to the main
Blue
Soundbar unit is connected properly or
Blinking
Recovering the connection
wait for a while. (If blinking persists, try
manually connecting the subwoofer.
See page 6.)
Red
On
Standby (with the Soundbar
Check if the power cable to the main
main unit turned off)
Soundbar unit is connected properly.
Connect again. See the instructions for
Connection failed
Red and
blue
Blinking
manual connection on page 6.
See the contact information for the
Malfunction
Samsung Service Centre in the manual.
ENG - 5
Manually connecting the subwoofer if automatic connection fails
Check before performing the manual connection
•• Check whether the power cables for the Soundbar and subwoofer are connected properly.
•• Make sure that the Soundbar is turned on.
1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.
The red indicator on the top of the subwoofer turns off and the blue indicator blinks.
ID SET
5 Sec
ID SET
POWER
Rear of the Subwoofer
Top of the Subwoofer
2. Turn off the Soundbar.
3. Press and hold the VOL button on the remote control for at least 5 seconds with the Soundbar
turned off (OFF).
Bl
u
PO eto
W oth
ER
4. The ID SET message appears on the display of the Soundbar for 1.3 seconds, and then disappear.
ID SET
D
N
SO
U
VO
L
BA
R
W
OO
FE
R
SO
M UN
OD D
E
Su
rro
un
d
5 Sec
5. When the blue indicator on the subwoofer blinks, turn on the Soundbar’s power by pressing
(Power) button on the right side of the main unit or on the remote control.
6. When the connection is successfully established, the blue indicator on the top of the subwoofer
stops blinking and glows continuously.
•• If the connection process fails, the blue indicator will flash continuously. Go to Step 1 and start again.
Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker
Kit (SWA-8500S) to your Soundbar (Sold separately). For more information, see the
Samsung Wireless Rear Speaker Kit manual.
ENG - 6
04 CONNECTING TO YOUR TV
Hear TV sound from your Soundbar through wired or wireless connections.
•• When the Soundbar is connected to a selected Samsung TVs, the Soundbar can be controlled using
the TV’s remote control.
–– When using optical cable, this feature can be supported by 2017 Samsung Smart TVs that
support Bluetooth.
–– This function also allows you to use the TV menu to adjust the sound field and various settings
as well as the volume and mute.
Method 1. Connecting with a Cable
Connecting using an Optical Cable
Bottom of the Soundbar
OPTICAL OUT
DIGITAL AUDIO IN
(OPTICAL)
Optical Cable
USB (5V 0.5A)
AUX IN
D.IN
Right Side of the Soundbar
1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV
with a digital optical cable.
2. Press the
(Source) button on the right side panel or remote control, and then select mode
“D.IN”.
•• When the Soundbar is connected to a Samsung smart TV released in 2017 or later, the
Bluetooth POWER function automatically turns on to enable the Soundbar to be controlled with
the TV remote control. (See page 14 for details on Bluetooth POWER.)
ENG - 7
Auto Power Link
Auto Power Link automatically turns on the Soundbar when the TV is turned on.
1. Connect the Soundbar and a TV with a digital optical cable.
2. Press the
(Source) button on the right side panel or on the remote control, and then select
“D.IN”.
3. Press the Left button on the remote control for 5 seconds to turn Auto Power
Link on or off.
•• Auto Power Link is set to ON by default.
(To turn off this function, turn off Auto Power using the Soundbar.)
•• Depending on the connected device, Auto Power Link may not function.
•• This function is only available in the “D.IN” mode.
Method 2. Connecting Wirelessly
Connecting a TV via Bluetooth
When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
•• Only one TV can be connected at a time.
The initial connection
1. Press the
(Source) button on the right side panel or on the remote control, and then select
“BT”.
2. Change “BT” to “BT PAIRING”.
•• If “BT READY” appears, press and hold the
(Source) button on the right side panel of the
Soundbar or on the remote control for more than 5 seconds to display “BT PAIRING”.
3. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)
4. Select “[AV] Samsung Soundbar Mxxx M-Series” from the list on TV’s screen.
An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV Bluetooth device list.
To connect to the Soundbar, select the message and establish a connection.
•• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.
5. You can now hear TV sound from the Soundbar.
ENG - 8
If the device fails to connect
•• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar Mxxx M-Series”)
appears in the list, delete it.
•• In “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side
panel of the Soundbar or on the remote control to switch to “BT PAIRING” mode.
Then, select “[AV] Samsung Soundbar Mxxx M-Series” from the TV’s search list.
What are the BT READY and BT PAIRING statuses?
•• BT READY : In this mode, you can search for previously connected TVs or connect to the Soundbar
from a previously connected mobile device.
•• BT PAIRING : In this mode, you can connect to a new device. (While in “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side of the Soundbar or on the remote
control.)
NOTES
•• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
•• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
•• The Soundbar automatically turns off after 5 minutes in the Ready state.
•• The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:
–– If there is a strong electrical field around the Soundbar.
–– If several Bluetooth devices are simultaneously paired with the Soundbar.
–– If the Bluetooth device is turned off, not in place, or malfunctions.
•• Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
Disconnecting the Soundbar from the TV
Press the
(Source) button on the right side panel or on the remote control and switch to any mode
but “BT”.
•• Disconnecting takes time because the TV must receive a response from the Soundbar.
(The time required may differ, depending on the TV model.)
•• To cancel automatic Bluetooth connection between the Soundbar and TV, press the
p (Play/Pause) button on the remote control for 5 seconds in “BT READY” status. (Toggle On → Off)
ENG - 9
05 CONNECTING AN EXTERNAL DEVICE
Connect to an external device via a wired or wireless network to play the external device’s sound
through the Soundbar.
Connecting using an Optical or Analogue Audio (AUX) Cable
BD / DVD player / Set-top box /
Right Side of the Soundbar
Game console
DIGITAL AUDIO IN
(OPTICAL)
OPTICAL OUT
Optical Cable
USB (5V 0.5A)
R - AUDIO - L
AUX IN
Audio (AUX) Cable
(not supplied)
Bottom of the Soundbar
1 Optical Cable
XX Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source
Device using a digital optical cable.
YY Select “D.IN” mode by pressing the
(Source) button on the right side panel or on the remote
control.
2 Audio (AUX) Cable
XX Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an
audio cable.
YY Select “AUX” mode by pressing
(Source) button on the right side panel or on the remote
control.
ENG - 10
06 CONNECTING A USB
You can play music files located on USB storage devices through the Soundbar.
USB port
DIGITAL AUDIO IN
(OPTICAL)
Display
DC 19V
USB (5V 0.5A)
AUX IN
USB
USB (5V 0.5A)
Micro USB to
USB adapter Cable
1. Connect a Micro USB to USB adapter cable with a male USB 2.0 Micro USB plug (Type B) on one
end and a standard female 2.0 USB jack (Type A) on the other end to the micro USB jack on your
Soundbar.
2. Connect your USB device to the female end of the adapter cable.
3. Press the
(Source) button on the right side panel or on the remote control, and then select
“USB”.
4. “USB” appears in the display screen.
5. Play music files from the USB storage device through the Soundbar.
•• The Soundbar automatically turns off (Auto Power Off) if no USB device has been connected for
more than 5 minutes.
Software Update
Samsung may offer updates for the Soundbar’s system firmware in the future.
If an update is offered, you can update the firmware by connecting a USB device with the firmware
update stored on it to the USB port on your Soundbar.
For more information about how to download update files, go to the Samsung Electronics website at
(www.samsung.com  Support).
Then, enter or select the model of your Soundbar, select Software & Apps, and then Downloads.
The option name can vary.
ENG - 11
07 CONNECTING A MOBILE DEVICE
Connecting via Bluetooth
When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of
cabling.
•• You cannot connect more than one Bluetooth device at a time.
Bluetooth device
The initial connection
1. Press the
(Source) button on the right side panel or on the remote control, and then select
“BT”.
2. Change “BT” to “BT PAIRING”.
•• If “BT READY” appears, press and hold the
(Source) button on the right side panel of the
Soundbar or on the remote control for more than 5 seconds to display “BT PAIRING”.
3. Select “[AV] Samsung Soundbar Mxxx M-Series” from the list.
•• When a Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT”
appears in the front display.
4. Play music files from the device, connected via Bluetooth, through the Soundbar.
If the device fails to connect
•• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar Mxxx M-Series”)
appears in the list, delete it.
•• In “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side
panel of the Soundbar or on the remote control to switch to “BT PAIRING” mode.
Then, select “[AV] Samsung Soundbar Mxxx M-Series” from the Bluetooth device search list.
For more information about Bluetooth connections, refer to “Connecting a TV via
Bluetooth” on pages 8~ 9.
ENG - 12
08 USING THE REMOTE CONTROL
How to Use the Remote Control
Turns the Soundbar on and off.
Power
Sound Control
Bluetooth
POWER
Surround
SOUND
MODE
VOL
WOOFER
SOUNDBAR
Bluetooth
POWER
Surround
Surround
Surround
You can select from TREBLE, BASS, or AUDIO
SYNC.
•• To control the volume of the treble or bass
sound, select TREBLE or BASS in Sound
Settings, and then adjust the volume
between -6~+6 by using the Up/Down
buttons.
•• If the video and audio between the TV and
your Soundbar are not synchronized, select
AUDIO SYNC in Sound Settings, and then
set audio delay between 0~300 milliseconds
by using the Up/Down buttons.
(Except “USB” mode)
•• Audio
Sync is only supported in some
Bluetooth
POWER
Bluetooth
functions.
POWER
The Surround Sound function adds depth and a
Bluetooth
Surround
SOUND
sense POWER
of space to sound.
MODE
SOUND
Each time you press this button, ON and OFF
MODE
Surround
alternate.
SOUND
MODE•• ON : Play sound over all the speakers.
•• OFF : You can hear the sound of the original
source channel from several speakers.
You can select the desired sound effect by choosing STANDARD, MUSIC, CLEAR VOICE,
VOL
WOOFER
SPORTS, or MOVIE.
SOUND
MODE
SOUND MODE
WOOFER
•• DRC (Dynamic Range Control) VOL
Lets you apply dynamic range control to Dolby Digital tracks. If you press and hold the
VOL
WOOFER
SOUND MODE button while in standby mode, DRC (Dynamic Range Control) turns on
or off. With the DRC turned on, loud sound is reduced. (The sound may be distorted.)
Press to select a source connected to the Soundbar.
WOOFER ••
VOL
Source
BT PAIRING mode
To turn on “BT PAIRING” mode in “BT” mode, press and hold the
for more than 5 seconds. See page 12 for details.
ENG - 13
(Source) button
Press the p button to pause a music file temporarily.
If you press the button again, the music file plays.
Play / Pause
Bluetooth
POWER
Surround
Press the indicated areas to select Up/Down/Left/Right.
SOUND
MODE
Up/Down/
Bluetooth
POWER
Surround
Left/Right
SOUND
MODE
Press Up/Down/Left/Right on the button to select or set functions.
•• Repeat
To use the Repeat function in “USB” mode, press the Up button.
VOL
VOL
WOOFER
WOOFER
•• Music Skip
Press the Right button to select the next music file. Press the Left button to select
the previous music file.
•• Auto Power Link
You can turn Auto Power Link on or off.
Auto Power Link is controlled by the Right and Left buttons respectively.
–– Auto Power Link : If the Soundbar is connected to your TV through a digital
optical cable, the Soundbar can automatically turn on when you turn on your TV.
Press and hold the Left button for 5 seconds to toggle Auto Power Link ON and
OFF.
–– Auto Power Link is set to ON by default.
Surround
Bluetooth
POWER
Bluetooth
SOUND
MODE
VOL
POWER
Press to turn the Bluetooth POWER function on and off.
When the Bluetooth POWER function is on, “ON-BLUETOOTH POWER” appears in the
Soundbar’s display.
•• Bluetooth POWER function : If the Soundbar is in standby mode and the Bluetooth
POWER function is On, when you turn on a previously connected Bluetooth device,
the Soundbar automatically turns on and connects via Bluetooth to the device.
•• If you press the Bluetooth POWER button again to turn off the BT function,
“OFF-BLUETOOTH POWER” appears in the Soundbar’s display.
•• If the “D.IN” mode is on and the Soundbar is connected to a Samsung smart TV
released in 2017 or later, the Soundbar can be controlled with the TV remote control.
In this mode, you cannot to turn off Bluetooth POWER.
WOOFER
ENG - 14
FE
R
SO
M UN
OD D
E
Bl
u
PO eto
W oth
ER
W
OO
BA
R
U
N
D
VO
L
U
N
D
SO
SO
SO
VO
L
U
N
D
VO
L
U
N
D
SO
Su
rro
un
d
R
FE
BA
R
SOUND
MODE
BA
R
BA
R
W
OO
W
OO
FE
SO
M UN
OD D
E
Su
rro
un
d
WOOFER
R
SO
M UN
OD D
E
Adjusting the Soundbar volume with a TV remote control
Use the TV menu to set the TV speaker on a Samsung TV to external speakers.
(For more information, see the TV’s user manual.)
•• After installing the Soundbar, you can adjust the Soundbar’s volume using the IR remote control
that came with a Samsung TV. (If you do not want to use this function, when the Soundbar is on,
press and hold the Surround button for 5 seconds. “OFF-TV REMOTE” appears in the Soundbar’s
display and the function turns off.) To adjust the volume using only the Samsung TV remote control,
press and hold the Surround button for more than 5 seconds until “SAMSUNG-TV REMOTE”
appears in the Soundbar display.
–– Each time the Surround button is held for 5 seconds, the mode switches in the following order:
“SAMSUNG-TV REMOTE” (Default mode) → “OFF-TV REMOTE” → “ALL-TV REMOTE”.
•• To adjust the Soundbar volume with the remote control that came with a TV made by a third party
manufacturer, turn the Soundbar on, press and hold the Surround button for 5 seconds
(“OFF-TV REMOTE” appears on the Soundbar’s display), release the Surround button, and then
press and hold the Surround button again for more than 5 seconds. (“ALL-TV REMOTE” appears on
the Soundbar’s display.)
–– This function may not be available, depending on the remote control.
–– For manufacturers that support this feature, refer to the FULL MANUAL
(www.samsung.com/support).
–– This volume control function works with IR TV remotes only. It does not work with Bluetooth
TV remotes (remotes that require pairing).
ENG - 15
N
D
BA
R
•• Mute
Press the VOL button to mute the sound. Press it again to unmute the sound.
SO
U
VO
L
BA
R
N
D
SO
U
VO
L
Push the button up or down to adjust the volume.
Su
rro
un
d
W
OO
F
ER
SO
M UN
OD D
E
Su
rro
un
d
W
OO
F
ER
SO
M UN
OD D
E
Su
rro
un
d
ER
W
OO
F
N
D
VO
L
BA
R
Su
rro
un
d
WOOFER
SO
M UN
OD D
E
VOL
VOL
Bl
u
PO eto
W oth
ER
Bl
u
PO eto
W oth
ER
Bl
u
PO eto
W oth
ER
Push the button up or down to adjust the volume of the subwoofer to -12 or -6 to +6.
Pressing the button reverts the subwoofer volume to level 0.
SO
U
Su
rro
un
d
Bluetooth
POWER
Surround
WOOFER
W
OO
FE
R
VOL
Bl
u
PO eto
W oth
ER
Bl
u
PO eto
W oth
ER
SOUND
MODE
09 INSTALLING THE WALL MOUNT
Installation Precautions
•• Install on a vertical wall only.
•• Do not install in a place with high temperature or humidity.
•• Verify whether the wall is strong enough to support the product’s weight. If not, reinforce the wall
or choose another installation point.
•• Purchase and use the fixing screws or anchors appropriate for the kind of wall you have (plaster
board, iron board, wood, etc.). If possible, fix the support screws into wall studs.
•• Purchase wall mounting screws according to the type and thickness of the wall you want to mount
the Soundbar on.
–– Diameter: M5
–– Length: 35 mm or longer recommended.
•• Connect cables from the unit to external devices before you install the Soundbar on the wall.
•• Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an
electric shock.
Wallmount Components
Wall Mount Guide
Holder-Screw (2 EA)
Screw (2 EA)
Bracket-Wall Mount L
ENG - 16
Bracket-Wall Mount R
1. Place the Wall Mount Guide against the wall
3. Push a pen tip or sharpened pencil tip
surface.
through the centre of the B-TYPE images on
•• The Wall Mount Guide must be level.
each end of the Guide to mark the holes for
•• If your TV is mounted on the wall, install
the supporting screws, and then remove the
the Soundbar at least 5 cm below the TV.
Wall Mount Guide.
5 cm or more
4. Using an appropriately sized drill bit, drill a
hole in the wall at each marking.
•• If the markings do not correspond to the
positions of studs, make sure you insert
appropriate anchors or mollies into the
holes before you insert the support
2. Align the Paper Template’s Centre Line with
screws. If you use anchors or mollies,
the centre of your TV (if you are mounting
make sure the holes you drill are large
the Soundbar below your TV), and then fix
enough for the anchors or mollies you
the Wall Mount Guide to the wall using tape.
•• If you are not mounting below a TV, place
the Centre Line in the centre of the
use.
5. Push a screw (not supplied) through each
Holder-Screw, and then screw each screw
installation area.
firmly into a support screw hole.
Centre Line
ENG - 17
6. Use the two Screws (M4 x L12) to attach both
•• The left and right mounts are different
shapes. Make sure to position them
Bracket-Wall Mount L and R to the
correctly.
Soundbar’s bottom.
For a proper fit, make sure to align the
bumps on the Soundbar to the holes on the
brackets.
Wall Mount R
Wall Mount L
7. Install the Soundbar with the attached
Bracket-Wall Mounts by hanging the
Bracket-Wall Mounts on the Holder-Screws
on the wall.
•• When assembling, make sure the hanger
part of the Bracket-Wall Mounts are
located behind the rear of the Soundbar.
Rear of Soundbar
•• Slightly tilt the Soundbar to insert both
Holder-Screw heads into Bracket-Wall
Mount holes. Push the Soundbar in the
direction of the arrow to make sure both sides
are firmly fixed.
Right end of Soundbar
ENG - 18
Detaching the Soundbar from
the Wall
1. To separate the Soundbar from the wall
mount, push it in the direction of arrow, tilt it
up slightly, and then pull it away from the
wall as shown.
•• Do not hang onto the installed unit and avoid
striking or dropping the unit.
•• Secure the unit firmly to the wall so that it
does not fall off. If the unit falls off, it may
cause an injury or damage the product.
•• When the unit is installed on a wall, please
make sure that children do not pull any of the
connecting cables, as this may cause it to fall.
•• For the optimal performance of a wall mount
installation, install the speaker system at
least 5 cm below the TV, if the TV is mounted
on the wall.
•• For your safety, if you do not mount the unit
on the wall, install it on a secure, flat surface
where it is unlikely to fall.
ENG - 19
10 TROUBLESHOOTING
Before seeking assistance, check the following.
The unit will not turn on.
Is the power cord plugged into the outlet?
;; Connect the power plug to the outlet.
A function does not work when the button is pressed.
Is there static electricity in the air?
;; Disconnect the power plug and connect it again.
Sound dropouts occur in BT mode.
;; See the Bluetooth connection sections on pages 8 and 12.
Sound is not produced.
Is the Mute function on?
;; Press the VOL button to cancel the function.
Is the volume set to minimum?
;; Adjust the Volume.
The remote control does not work.
Are the batteries drained?
;; Replace with new batteries.
Is the distance between the remote control and Soundbar main unit too far?
;; Move the remote control closer to the Soundbar main unit.
The red LED on the subwoofer blinks and the subwoofer is not producing sound.
This issue can occur if the subwoofer is not connected to the Soundbar main unit.
;; Try to connect your subwoofer again. (See page 5.)
The subwoofer drones and vibrates noticeably.
Try to adjust the vibration of your subwoofer.
;; Push the WOOFER button on your remote control up or down to adjust the subwoofer volume.
(between -12, -6 ~ +6).
ENG - 20
11 LICENCE
13 IMPORTANT
NOTES ABOUT
SERVICE
Manufactured under license from Dolby
Figures and illustrations in this User Manual are
Laboratories. Dolby, Dolby Audio, Pro Logic,
provided for reference only and may differ from
and the double-D symbol are trademarks of
actual product appearance.
Dolby Laboratories.
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS
Licensing Limited. DTS, the Symbol, DTS in
combination with the Symbol, and DTS 2.0
Channel are registered trademarks or
trademarks of DTS, Inc. in the United States
and/or other countries. © DTS, Inc. All Rights
Reserved.
12 OPEN SOURCE
LICENCE NOTICE
To send inquiries and requests regarding open
sources, contact Samsung via Email
(oss.request@samsung.com).
ENG - 21
14 SPECIFICATIONS AND GUIDE
Specifications
USB
Weight
GENERAL
AMPLIFIER
Dimensions
(W x H x D)
5V/0.5A
Soundbar Main Unit
1.5 kg
Subwoofer (PS-WM20)
4.6 kg
Soundbar Main Unit
907.5 x 53.5 x 70.5 mm
Subwoofer (PS-WM20)
179.0 x 353.0 x 299.5 mm
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % ~ 75 %
Rated Output
power
Soundbar Main Unit
35W x 2, 6 ohm
Subwoofer (PS-WM20)
130W, 3 ohm
Supported play formats
(DTS 2.0 sound is played in DTS format.)
LPCM 2ch, Dolby Audio™
(supporting Dolby® Digital), DTS
NOTES
•• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
•• Weight and dimensions are approximate.
•• For more information about the power supply and power consumption, refer to the label attached
to the product. (Label : Bottom of the Soundbar Main Unit)
•• For India Only
“This product is RoHS compliant”
ENG - 22
© 2017 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care Centre.
Area
Contact Centre 
Web Site
` Asia Pacific
CHINA
400-810-5858
www.samsung.com/cn/support
HONG KONG
3698 4698
www.samsung.com/hk/support (Chinese)
www.samsung.com/hk_en/support (English)
MACAU
0800 333
www.samsung.com/support
SINGAPORE
1800 7267864 | 1800-SAMSUNG
www.samsung.com/sg/support
AUSTRALIA
1300 362 603
www.samsung.com/au/support
NEW ZEALAND
0800 726 786 (All Product)
0800 6 726 786
www.samsung.com/nz/support
VIETNAM
1800 588 889
www.samsung.com/vn/support
THAILAND
0-2689-3232
1800-29-3232 (Toll free)
www.samsung.com/th/support
MYANMAR
+95-1-2399-888
www.samsung.com/mm/support
CAMBODIA
+855-23-993232
1800-20-3232 (Toll free)
www.samsung.com/th/support
LAOS
+856-214-17333
MALAYSIA
1800-88-9999
+603-7713 7420 (Overseas contact)
www.samsung.com/my/support
INDONESIA
021-5699-7777
0800-112-8888 (All Product, Toll Free)
www.samsung.com/id/support
PHILIPPINES
1-800-10-726-7864 [ PLDT Toll Free ]
1-800-8-726-7864 [ Globe Landline and Mobile ]
02-422-2111 [ Standard Landline ]
www.samsung.com/ph/support
TAIWAN
0800-329-999
www.samsung.com/tw/support
INDIA
1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
NEPAL
16600172667 (Toll Free for NTC Only)
9801572667
BANGLADESH
09612300300
08000300300 (Toll free)
SRI LANKA
+9411SAMSUNG (+94117267864)
+94117540540
+94115900000
AH68-02981Q-03
www.samsung.com/in/support
AH68-02981Q-03
Download PDF

advertising