Samsung | DVD-P490 | Samsung DVD-P490 User Manual

DVD-P490
DVD Player
user manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive more complete service, please register your
product at
www.samsung.com/global/register
AK68-01768A(01)
precautions
1. Setting up
- Refer to the identification label located on
the rear of your player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not
block ventilation holes on any of the components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you don’t use
it for a long time.
- The mains plug is used as a disconnect
device and shall readily operable at any
time.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
- Do not open covers and do not repair yourself. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this product is for personal use only.
- Apparatus shall not be expossed to dripping
or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button,
or disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
_ precautions
- When condensation forms inside the player
due to sharp changes in temperature, the
player may not operate correctly. If this
occurs, leave the player at room temperature until the inside of the player becomes
dry and operational.
4. Disc
- Do not clean record-cleaning sprays, benzene, thinner, or other volatile solvents that
may cause damage to the disc surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man ner, according to federal, state, and local regulations.
The product unit accompanying this user manual
is licensed under certain intellectual property rights
of certain third parties. This license is limited to
private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Before You Start Table of Content
Accessories
User’s Manual
Batteries for Remote
Control (AAA Size)
Video/Audio
Cable
The accessories which are not supplied are:
• Component Cable
• Coaxial Cable.
Install Batteries in the Remote control
1. Open the battery cover on the back of the remote control.
2. Insert two AAA batteries.
Make sure that the polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate
properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by obstacles.
- Check if there is any fluorescent lighting nearby.
English _
● SETUP
Remote Control
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control. . . . . . . . . . . . . . . . . . . 8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using the Search and Skip Functions . . . . . . . . . 16
Using the Display Function . . . . . . . . . . . . . . . . . 16
Using the Disc and Title Menu . . . . . . . . . . . . . . . 17
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Advanced Functions
Adjusting the Aspect Ratio (EZ View). . . . . . . . . . 18
Selecting the Audio Language . . . . . . . . . . . . . . . 18
Selecting the Subtitle Language. . . . . . . . . . . . . . 19
Changing the Camera Angle. . . . . . . . . . . . . . . . . 19
Using the Bookmark Function. . . . . . . . . . . . . . . . 19
Using the Zoom Function . . . . . . . . . . . . . . . . . . . 20
Clips Menu for MP3/WMA/JPEG/MPEG4/
CD Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 21
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 21
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . 22
Playing Media files Using the USB
Host feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 24
Changing Setup Menu
Using the Setup Menu. . . . . . . . . . . . . . . . . . . . . . 26
Setting Up the Language Features. . . . . . . . . . . . 26
Setting Up the Audio Options . . . . . . . . . . . . . . . . 27
Setting Up the Display Options. . . . . . . . . . . . . . . 29
Setting Up the Parental Control . . . . . . . . . . . . . . 30
Reference
Firmware upgrade. . . . . . . . . . . . . . . . . . . . . . . . . 32
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
setup
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional interlaced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
MPEG4
This unit can play MPEG4 formats within an avi file.
CD Ripping
This feature lets you to copy audio files from disc
to USB device into MP3 format (only audio CD (CD DA)).
_ setup
Note
-Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
-Ability to play back may depend on recording conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
-The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copyprotected DVD discs.
This product incorporates copyright protection technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS
(576p)
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IN CASE OF 576 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY
WITH THIS MODEL 576p DVD PLAYER, PLEASE
CONTACT SAMSUNG'S CUSTOMER SERVICE
CENTER.”
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Disc Types
(Logos)
Recording
Types
Audio
+
Video
VIDEO-CD
Audio
+
Video
AUDIO-CD
Audio
Max. Playing Time
12 Cm
Single-sided 240 min.
Double -sided 480 min.
8 Cm
Single-sided 80 min.
Double -sided 160 min.
12 Cm
74 min.
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
Disc Markings
~
PAL
Play Region Number
PAL broadcast system in U.K, France,
Germany, etc.
Dolby Digital disc
STEREO
STEREO
DIGITAL
SOUND
Stereo disc
Digital Audio disc
Characteristics
- DVD contains excellent sound and video due to Dolby Digital and MPEG-2 system.
- Various screen and audio functions
can be easily selected through the
on screen menu.
- Video with CD sound, VHS quality &
MPEG-1 compression technology.
- CD is recorded as a Digital Signal with better audio quality, less
distortion and less deterioration of
audio quality over time
Region Number
Both the DVD player and the discs are coded
by region. These regional codes must match
in order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the rear panel of the player.
DTS disc
MP3 disc
You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to
play them back and it may cause damage to
the DVD player.
DivX Certification
DivX, DivX Certified, and associated logos are trademarks of
DivXNetworks, Inc and are used under
license
English _
● SETUP
DVD
Disc Size
setup
Description
Front Panel Controls
1. STANDBY/ON ( )
When STANDBY/ON is pressed on, the player is turned
on.
2. DISC TRAY
Place the disc here.
3. USB Host
4. DISPLAY
Operation indicators are displayed here.
5. OPEN/CLOSE/ STOP ( )
Press to open and close the disc tray/Stops disc play.
6. PLAY/PAUSE (
)
Begin or pause disc play.
Connect digital still camera, MP3 player, memory stick,
Card reader, or another removable storage devices.
Front Panel Display
Total playing time/Displays various messages concerning operations such as PLAY,
STOP, LOAD ...
nodISC: No disc loaded.
OPEn: The disc tray is open.
LOAd: Player is loading disc information.
_ setup
Rear Panel
1
2
● SETUP
3
1.
5.1CH ANALOG AUDIO OUT JACKS
- Connect to an amplifier with 5.1ch analog input
jacks.
2. DIGITAL AUDIO OUT JACKS
- Use a coaxial digital cable to connect to a
compatible Dolby Digital receiver.
- Use a coaxial digital cable to connect to an A/V
Amplifier that contains a Dolby Digital, MPEG2
or DTS decoder.
4
4. COMPONENT VIDEO OUT
JACKS
- Use these jacks if you have a TV with
Component Video in jacks. These jacks provide PR, PB and Y video.
- If Component(P-SCAN) Video Output is selected in Setup Menu, progressive scan mode will
work.
- If Component(I-SCAN) Video Output is selected in Setup Menu, interlaced scan mode will
work.
3. VIDEO OUT JACK
- Use a video cable to connect to the Video
input jack on your television.
- The Video Output in Setup Menu must be set
to Component(I-SCAN).
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan
settings in the TV’s menu system.
- See pages 29 ~ 30 to get more information on how to use the setup menu.
English _
setup
Tour of the Remote Control
1
2
3
4
5
6
7
8
12
13
14
15
16
17
18
9
10
19
11
20
_ setup
1. DVD POWER Button
Turns the power on or off.
2. REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
3. DISC MENU Button
Brings up the Disc menu.
4. BOOKMARK Button
)
5. SEARCH Buttos (
/
Allow you to search forward/backward through a disc.
6. STOP Button (
)
Press to stop a disc.
7. SUBTITLE (π)Button
8. MENU Button
Brings up the DVD player’s menu.
9. AUDIO (√) Button
Use this button to access various audio functions on a disc.
10. ENTER/π/†,√/® Buttons
This button functions as a toggle switch.
11. INFO Button
Displays the current disc mode.
12. OPEN/CLOSE (
) Button
To open and close the disc tray.
13. REPEAT A-B Button
Allows you to repeat A-B disc.
14. USB Button
15. VIDEO SEL. Button
Selects video output formats.
16. PLAY/PAUSE Button (
)
Begin/Pause disc play.
17. SKIP Buttons (
)
/
Use to skip the title, chapter or track.
18. RETURN Button
Returns to a previous menu.
19. TITLE MENU (®) Button
Bring up the Title menu.
20. CANCEL Button
Use to remove menus or status displays from the
screen.
connections
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connection to a TV (For Video)
1
Using video/audio cables, connect the VIDEO (yellow)/
AUDIO (red and white) OUT terminals of 5.1 CH (front
L-R) on the rear of the DVD player to the VIDEO (yellow)/
AUDIO (red and white) IN terminals of TV.
2
Turn on the DVD player and TV.
RED
WHITE
YELLOW
Audio Cable
Video Cable
RED
WHITE
YELLOW
3
Press the TV/VIDEO button on the TV's remote
control to select Video.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to
14)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's
manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the
DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video
Output mode changes in the following sequence: I-SCAN ➝ P-SCAN
English _
● connections
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
connections
Connection to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio
signals are delivered through the audio output.)
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals of 5.1 CH (Front L-R)on the rear of
the DVD player to the AUDIO (red and white) IN terminals
of TV. Turn on the DVD player and TV.
3
Press the TV/VIDEO button on the TV's remote control to
select Component or DVD.
BLUE
RED
GREEN
RED
WHITE
Audio Cable
RED
WHITE
RED
BLUE
GREEN
Component cable
(not included)
4
Set the Video Output to I-SCAN in the Display Setup
menu. (See pages 29 to 30)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12 to 14)
- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y” depending on the manufacturer. The number and position of terminals can vary depending on the TV set.
Please refer to the user's manual of the TV.
10_ connections
Connection to a TV (Progressive)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio
signals are delivered through the audio output.)
● connections
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals of 5.1 CH (Front L-R)on the rear of
the DVD player to the AUDIO (red and white) IN terminals
of TV. Turn on the DVD player and TV.
3
Press the input selector on your TV remote control until
the Component signal from the DVD player appears on the
TV screen.
BLUE
RED
GREEN
RED
WHITE
Audio Cable
RED
WHITE
RED
BLUE
GREEN
Component cable
(not included)
4
Set the Video Output to P-SCAN in the Display Setup
menu. (See pages 29 to 30)
You can use the VIDEO SEL. button to change the Video
Output mode. (See page 9)
To see the progressive video output,
You
need ayour
TV set
the progressive
scanif your TV supports Progressive Scan. If Progressive
-
Consult
TVsupporting
User’s Manual
to find out
input
isfunction.
And you
havethe
to set
the TV
menu regarding Progressive Scan settings in the TV’s
Scan
supported,
follow
TV up
User’s
Manual
tomenu
the system.
progressive scan input.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method has. Progressive
scanning method can provide better and clearer picture quality.
English _11
connections
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT terminals of 5.1 CH (Front L-R)on the rear of
the DVD player to the AUDIO (red and white) IN terminals of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD player to the VIDEO or COMPONENT IN terminal of your TV.
RED
3
WHITE
Audio Cable
Turn on the DVD player, TV, and Amplifier.
RED
WHITE
2-channel amplifier
4
Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 27 to 29)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
12_ connections
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
● connections
If using a coaxial cable (not included), connect the
DIGITAL AUDIO OUT (COAXIAL) terminal on the rear
of the DVD player to the DIGITAL AUDIO IN (COAXIAL)
terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD
player to the VIDEO or COMPONENT IN terminal of TV.
Coaxial Cable
(not included)
3
Turn on the DVD player, TV, and Amplifier.
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 27 to 29)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
English _13
connections
Connection to a 5.1CH Analog Amplifier
1
If using audio cables for 5.1 CH Analog Amplifier (not
included) connect the 5.1CH ANALOG AUDIO OUT terminals on the rear of the DVD player to the 5.1CH ANALOG
AUDIO IN terminals of the 5.1CH Analog Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT terminals on the rear of the DVD player
to the VIDEO or COMPONENT terminals of your TV as
described on pages 9 to 11.
3
RED
RED
WHITE
WHITE
BLACK
BLACK
Turn on the DVD player, TV, and Amplifier.
5.1ch Analog
Amplifier
4
Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 27 to 29)
- The position of terminals may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.
14_ connections
basic functions
Playing a Disc
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the
DVD POWER button, this screen comes up: If you want
to select a language, press a π/† button and then press
the ENTER button. (This screen will only appear when
you plug in the player for the first time.)
If the language for the startup screen is not set, the settings may change whenever you turn the power on or off.
Therefore, make sure that you select the language you
want to use.
Once you select a menu language, you can change it
button on the front panel of the unit
by pressing the
for more than 5 seconds with no disc in the unit. Then
the SELECT MENU LANGUAGE window appears again
where you can reset your preferred language.
Playback
1. Press the OPEN/CLOSE ( ) button. The tray opens.
2. Place a disc gently into the tray with the disc’s label facing up.
) button during play.
5. Removing Disc
Press the OPEN/CLOSE (
) button.
6. Pausing Play
Press the PLAY/PAUSE ( ) button on the remote control
during play.
- Screen stops, no sound.
To resume, press the PLAY/PAUSE ( )‑button once again.
7. Step Motion Play (Except CD)
Press the SKIP ( ) button on the remote control
during PAUSE mode.
- Each time the button is pressed, a new frame will appear.
- No sound is heard during STEP mode.
- Press the PLAY ( ) button to resume normal play.
- You can only perform step motion play in the
forward direction.
8. Slow Motion Play
Press the SEARCH ( / ) button to choose the play speed between 1/2, 1/4 and1/8 of normal during‑PAUSE mode.
- No sound is heard during slow mode.
- Press the PLAY ( ) button to resume normal play.
Note
- If the player is left in the stop mode for more than one minute without any user interaction, a
screen saver will be activated. Press thePLAY/
PAUSE ( )button to resume normal play.
- If the player is left in the stop mode for more than about 30 minutes, the power will automatically shut off.(Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause mode, it will stop.
- This ( ) icon indicates an invalid button press.
3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE ( ) button to close the disc tray.
- When you stop disc play, the player remembers where you stopped, so when you press PLAY/PAUSE ( ) button again, it will pick up where you left off.
English _15
● basic functions
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
4. Stopping Play
Press the STOP (
basic functions
Using the Search and Skip
Functions
During play, you can search quickly through a chapter or
track, and use the skip function to jump to the next selection.
Searching through a Chapter or
Track
During play, press the SEARCH ( or
remote control for more than 1 second.
DVD
2X, 4X, 64X, 128X
CD
2X, 4X, 8X
VCD
) button on the
4X, 8X
Note
- The speed marked in this function may be different from the actual playback speed.
- No sound is hearing during search mode (Except CD).
Using the Display Function
When Playing a DVD/VCD/MPEG4
1. During play, press the INFO button on the remote control.
2. Press the π/† buttons to select the desired item.
- When playing VCD, the Disc menu may not work.
3. Press the √/® buttons to make the desired setup and then press the ENTER button. You may use the number but tons of the remote control to directly access a title, chap ter or to start the playback from a desired time.
4. To make the screen disappear, press the CANCEL button.
Note
Title
Chapter
Most DVD discs are recorded in chapters
so that you can quickly find a specific passage (similar to tracks on an video CD).
Time
Allows playback of the film from a desired
time. You must enter the starting time as
a reference.The time search function does
not operate on some disc.
Skipping Tracks
During play, press the SKIP (
or
) button.
- When playing a DVD, if you press the SKIP ( ) button, it moves to the next chapter. If you press the SKIP (
) button, it moves to the beginning of the chapter. One
more press makes it move to the beginning of the previous
chapter.
- When playing a CD in Menu Off mode, if you press the
SKIP ( ) button, it moves to the next track. If you press
the SKIP ( ) button, it moves to the beginning of the track.
One more press makes it move to the beginning of the
previous track.
- If a track exceeds 15 minutes when playing a VCD and you press the
press the
button, it moves forward 5minutes. If you
button, it moves backward 5 minutes
Note
When playing VCD, the Disc menu may not work.
16_ basic functions
To access the desired title when there is
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
Audio
Subtitle
S hortcut
Refers to the language of the film
soundtrack. In the example, the
soundtrack is played in English 5.1CH. A
DVD disc can have up to eight different
soundtracks.
Refers to the subtitle languages available
in the disc. You will be able to choose the subtitle languages or, if you prefer, turn
them off from the screen. A DVD disc can
have up to 32 different subtitles.
To access the desired Bookmark, Angle,
Zoom or EZ View function.
Some DVD discs are have more angle
function from any picture.
Bookmark function make you easily and
quickly to find a track or chapter from DVD or VCD ( Menu Off).
The EZ View function is use for changing
the aspect ratio in DVD.
The Zoom function is use for Enlarge DVD
or VCD Picture.
DVD
Using the Disc and Title
Menu
Chapter
Using the Disc Menu
1. During the playback of a DVD disc, press the‑MENU button
on the remote control.
2. Press the π/† buttons to select Disc Menu, then‑press the
® or ENTER button.
Title
Using the A-B Repeat function
Note
- Depending on a disc, the Disc Menu may not work.
- You can also use the Disc Menu, using the DISC
MENU button on the remote control.
- When playing VCD, the Disc Menu may not work.
1. Press the REPEAT A-B button at the point where you
want repeat play to start (A).
2. Press the REPEAT A-B button at the point where you
want the repeat play to stop (B).
- To return to normal play, press the CANCEL button.
DVD
Repeat : A-
Using the Title Menu
Repeat : A-B
1. During stop mode of a DVD disc, press the MENU button
on the remote control.
2. Press the π/† buttons to select Title Menu, then press the
® or ENTER button.
Press ENTER key
for Title Menu
Note
- Depending on a disc, the Title Menu may not
work.
- Title Menu will only be displayed if there are at
least two titles in the disc.
Repeat Play
Press the REPEAT button to change playback
mode.
When playing a DVD
Note
- A-B REPEAT allows you to set point (B) until at
least 5 seconds of play back time has elapsed
after point(A) has been set.
- Depending on a disc, the Repeat function may not work.
Slow Play
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being
played etc., so you can study them more closely.
When playing a DVD
1. During play, press the PLAY/PAUSE ( ) button.
2. Press the SEARCH ( / ) button to choose the play
speed between 1/2, 1/4 and 1/8 of normal during PAUSE
mode.
- DVD repeats play by chapter or title.
- Chapter : repeats the chapter that is playing.
- Title : repeats the title that is playing.
- Off
English _17
● basic functions
Repeat : Off
Press ENTER key
for Disc Menu
advance functions
Adjusting the Aspect Ratio
(EZ View)
To play back using aspect ratio
(DVD)
1. During play, press the INFO button on the remote
control.
2. Press the ▲ / ▼ buttons to select Shortcut.
3. Press the √ / ® buttons to select EZ View,
then‑press ENTER button.
• The screen size changes when the ® button is
pressed repeatedly.
• The screen zoom mode operates differently
depending on the screen setting in the Display
Setup menu.
• To ensure correct operation of the EZ VIEW
button, you should set the correct aspect ratio in
the Display Setup menu. (See pages 29 to 30).
4:3 Letter Box
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- NORMAL Wide
Displays the content of the DVD title in 16:9 aspect ratio.
- Screen Fit
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- Zoom Fit
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- NORMAL SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- Screen Fit
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- Zoom Fit
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- VERTICAL FIT
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
18_ advance functions
If you are using a 4:3 TV
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio. The black bars will appear at the top and bottom of the screen.
4:3 Pan Scan
The left and right portions of the screen are cut off and the central portion of the 16:9 screen is displayed.
- Screen Fit
The top and bottom portions of the screen are cut off and a full screen appears. The picture will look vertically stretched.
- Zoom Fit
The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- NORMAL SCREEN
Displays the content of the DVD title in 4:3 aspect ratio.
- Screen Fit
The top and bottom portions of the screen are cut off and the full screen appears. The picture will look vertically stretched.
‑ Zoom Fit
The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged.
Note
This function may behave differently depending on
the type of disc.
Selecting the Audio
Language
You can select a desired audio language quickly and
easily with the AUDIO button.
Using the AUDIO/ √ button (DVD/
VCD/MPEG4)
1. Press the AUDIO/√ button. The Audio changes when the button is pressed repeatedly.
The audio languages are DVD represented by abbreviations.
When playing a VCD you
can select among Stereo,
Right or Left.
Stereo
AUDIO
Press Audio button at
remocon repeatedly to
select the desired Audio
on MPEG4 then press
the ENTER .
Changing the Camera
Angle
MPEG4
PCM 1/2
AUDIO
2. To remove the AUDIO icon, press the CANCEL or RETURN button.
Selecting the Subtitle
Language
4. Press the √/® buttons on the remote control to select the
desired angle.
You can select a desired subtitle quickly and
easily with the SUBTITLE/ π button.
Using the SUBTITLE/ π button
(DVD/MPEG4)
1. Press the SUBTITLE/ π button. The subtitle languages are represented by abbreviations. The subtitle changes when the button is pressed repeatedly.
External Subtitle option
will appear, depends on
the DivX disc.
MPEG4
Subtitle Selection
External Subtitle Off
readme.TXT
Non-standard fonts are not supported
Press SUBTITLE button
at remocon repeatedly to
select the desired subtitle
language on a MPEG4
then press the ENTER .
Enter
Return
Menu
MPEG4
Off
1. During play, press the INFO button on the remote control.
2. Press the π/† buttons to select Shortcut.
3. Press the √/® buttons to select Angle, then ‑press the
ENTER button.
SUBTITLE
4/6
Note
- If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Depending on the disc, these functions may not
work.
Using the Bookmark
Function
This feature lets you bookmark sections of a DVD or
VCD (Menu Off mode) so you can quickly find them
at a later time.
Using the Bookmark Function
(DVD/VCD)
1. During play, press the INFO button on the remote control.
2. Press the π/† buttons to select Shortcut.
DVD
2. To remove the SUBTITLE icon, press the CANCEL or RETURN button.
Note
- You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC MENU button.
- This function depends on what subtitles are encoded on the disc and may not work on all DVDs.
- A DVD disc can contain up to 32 subtitle languages.
- To have the same subtitle language come up whenever you play a DVD; Refer to “Using the Subtitle Language” on page 27.
VCD
English _19
● advance functions
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up
whenever you play a DVD;
- Refer to “Using the Audio Language” on page 27.
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE button (DVD)
If the disc contains multiple angles, the ANGLE
appears on the screen.
advance functions
3. Press the √/® buttons to select Bookmark (except VCD), then press the ENTER button.
4. When you reach the scene you want to mark, press‑the
ENTER button. Up to three scenes may be marked at a time.
1 - -
Note
- Only Menu Off is available for VCD2.0. Each
press of the DISC MENU button toggles between
Menu‑On and Menu Off.
- Depending on a disc, the Bookmark function may
not work.
Using the Zoom Function
Using the Zoom Function (DVD/
VCD)
1. During play, press the INFO button on the remote control.
2. Press the π/† buttons to select Shortcut.
3. Press the √/® buttons to select Zoom, then press the
ENTER button.
- During DVD play, press ENTER to zoom in 2X/4X/2X/
Normal in order.
- During VCD play, press ENTER to zoom in
2X/4X/2X/Normal‑in order.
Recalling a Marked Scene
1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function” on page 19.
4. Press the √/® buttons to select a marked scene.
2X
1 2 3
5. Press the PLAY/PAUSE (
scene.
) button to skip to the marked Clearing a Bookmark
1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function” on page 19.
4. Press the √/® buttons to select the bookmark number you want to delete.
5. Press the CANCEL button to delete a bookmark number.
1 2 3
20_ advance functions
Clips Menu for MP3/WMA/
JPEG/ MPEG4/CD Audio
CD Audio or discs with MP3/WMA/JPEG contain
individual songs and/or pictures that can be organized into folders as shown below. They are similar
to how you use your computer to put files into different folders.
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
Stop
Off
-
: Name of currently playing file.
: Current Playback Time.
: Current Playback Mode : There are four modes. They can be selected in order by pressing the REPEAT button.
- Off: Normal Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a folder contains both MP3 and WMA files.
2. Press the π/† or √/® buttons to select a song file.
‑ Press ENTER to begin playback of the song file.
- Track: Repeats the current track.
Off
Play
00:00:23
B e c a u s e Yo u
...
- Folder: Repeats the current folder B e c a u s e Yo u
Cactus
- Random: Files in the disc will be played in Sad Dayu
Wonderful
random order.
Enter
Return
REPEAT
Repeat
- : MP3 file icon. : CD Audio file icon.
Repeat/Random playback
-
: WMA file icon. -
: Folder icon.
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same extension in the current folder.
- Random: Song files which have the same extension will be played in random order.
To resume normal play, press the CANCEL button.
-
: JPEG file icon -
: Current Folder icon.
: AVI file icon.
Folder Selection
The folder can be selected in Stop or Play mode.
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press the π/† buttons to select “..” and press ENTER to go to the parent folder.
-To select the Peer Folder
Press the √/® buttons to highlight left window. Press the ▲ / ▼ buttons to select the desired folder, then press ENTER.
-To select the Sub-Folder
Press the √/® buttons to highlight right window. Press the π/† buttons to select the desired folder,then press ENTER.
Root
WMA
JPEG
Parent Folder
MP3
MUSIC
Current Folder
1st
Sub-Folders
2nd
SONG FILE 1
Peer Folders
SONG FILE 2
SONG FILE 3
MPEG4 FILES
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET format.
ISO 9660 format and Joliet MP3 or WMA files are compatible with Microsoft's DOS and Windows, and with Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8 characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When com
posing your title, make sure that you use 8 characters or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of compression/ decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to MP3 format, of at least 128 Kbps and up to 160 Kbps. However, choosing higher rates, like 192 Kbps or more, only rarely give better sound quality. Conversely, files with decompression rates below 128 Kbps will not be played properly.
- Use a decompression transfer rate of at least 64Kbps when recording WMA files.
Sound quality with WMA files basically depends on the rate of compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling rate, that is conversion to WMA format, of at least 64Kbps and up to 192Kbps. Conversely, files with decompression rates below 64Kbps or over 192Kbps will not be played prop
erly.
English _21
● advance functions
MP3/WMA/CD Audio
Playback
advance functions
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to prevent illegal copying. These files are of the following types: Windows MediaTM (registered trade mark of Microsoft Inc) and SDMITM (registered trade mark of The SDMI Foundation). You cannot copy such files.
- Important:
The above recommendations cannot be taken as a guarantee that the DVD player will play MP3 recordings, or as an assurance of sound quality. You should note that certain technologies and methods for MP3 file recording on CD-Rs prevent optimal playback of these files on your DVD player (degraded sound quality and in some cases, inability of the player to read the files).
- This unit can play a maximum of 500 files and 500 folders per disc.
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video data. Only
AVI format files with the “.avi” extensions can be played.
1. Open the disc tray. Place the disc on the tray.
Close the tray.
2. Press the π/† or √/® buttons to select an avi file
(DivX/XviD) and then press ENTER button.
Stop
T
00:00:00
...
a01_divx51b-8
a02_divx505b-8
a03_divx502sp-8
a04_divx412-8
Enter
Return
Menu
Repeat playback
Press the REPEAT button to change playback mode. There are
4 modes, such as Off, Folder, Title an A-B (a distance between
two points appointed by user)
- Folder : repeats the AVI files which have the same extension
in the current folder.
- Title : repeats the title that is playing.
22_ advance functions
Function
Description
Reference page
Skip
( or )
During play, press
the or
button, it moves forward or
backward 5 minutes.
-
During play, press the
SEARCH ( or ) button and press again to search
at a faster speed. Allows you
to search at a faster speed
in an AVI file. (2X, 4X, 8X)
-
Slow Motion
Play
Allows you to search at a
slower speed in an AVI file.
(1/2X, 1/4X, 1/8X)
P 15
Step Motion
Play
Press the SKIP ( ) button on the remote control
during PAUSE mode, a
new frame will appear.
P 15
ZOOM
2X/4X/2X/Normal in order
P 20
Search
( or )
- These functions may not work depending on MPEG4
file.
CD-R AVI file
Off
/MPEG4
MPEG4 Function Description
This unit can play the following video compression formats
within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple Profile)
- DivX 5 contents (MPEG-4 simple profile plus additional
features such as bi-directional frames. Qpel and GMC are
also supported.)
- XviD MPEG-4 compliant Contents.
This unit supports all resolutions up to maximum below.
DivX3.11 & DivX4 & XviD
Bitrate may fluctuate:
Device may skip decoding
the high bitrate portions
and begin decoding again
when Bitrate returns to normal.
DivX5
720 x 480 @30fps
720 x 576 @25fps
: Maximum bitrate : 4Mbps
Note
• Some MPEG-4 files created on a personal computer
may not be play back. That is why Codec Type,
Version and Higher resolution over specification is
not supported.
• This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
You can enjoy the media files such as pictures, movies
and tunes saved in an MP3 player, USB memory or digital
camera in high audio by connecting the storage device to
the USB port of the DVD Player.
Using the USB HOST feature
1. Connect the USB device to the USB port on the front of the
unit.
2. If there is partision Of USB, Press the π/† button to select
the one of partision from USB, then Press OK.
Disc
USB
3. Press the π/† or √/® buttons to select a file in
USB. Press OK to Open file.
STOP
Off
00:00:00
During playback, press the (
/
) button.
• When there is more than one file, when you press the
button, the next file is selected.
• When there is more than one file, when you press the button, the previous file is selected.
Fast playback
To play back the disc at a faster speed, press ( / ) during playback.
• Each time you press either button, the playback speed will
change as follows: 2x ➞ 4x ➞ 8x.
Compatible Devices
1. USB devices that support USB Mass Storage v1.0.
(USB devices that operate as a removable disk in Windows (2000 or later) without additional driver installation.)
2. MP3 Player: Flash type MP3 player.
3. Digital camera: Cameras that support USB Mass Storage v1.0.
• Cameras that operate as a removable disk in Windows (2000 or later) without additional driver installation.
4. USB Flash Drive: Devices that support USB2.0 or USB1.1.
•You may experience a difference in playback quality when you connect a USB1.1 device.
5. USB card Reader: One slot USB card reader and Multi slot
USB card reader
• Depending on the manufacturer. the USB card reader may not be supported.
• If you install multiple memory devices into a multi card
reader, you may experience problems.
6. If you use a USB extension cable, the USB device might not
be recognized.
• Supported Formats
Note
• Each time the USB button on the remote control is
pressed, a frame of the USB device selection will
appear.
• “USB” appears on the display screen.
• USB MENU screen appears on the TV screen and the
saved file is played.
Safe USB Removal
To prevent damage to the memory stored in the USB device,
perform safe removal before disconnecting the USB cable.
- Press the STOP ( ) button
- Remove the USB cable.
English _23
● advance functions
Playing Media Files Using
the USB Host feature
Skip Forward/Back
advance functions
• CBI (Control/Bulk/Interrupt) is not supported.
• Digital Cameras that use PTP protocol or require additional
program installation when connected to a PC are not
supported.
• A device using NTFS file system is not supported.
(Only FAT 16/32 (File Allocation Table 16/32) file system is
supported.)
• Some MP3 players, when connected to this product,may not
operate depending on the sector size of their file system.
• The USB HOST function is not supported if a product that
transfers media files by its manufacturer-specific program is
connected.
• Does not operate with Janus enabled MTP(Media Transfer
Protocol) devices.
3. Press the π/† buttons to select START,‑then‑press the
ENTER button.
File copy begins.
- To cancel the copying in progress, press the CANCEL but
ton.
Play
00:03:15
Track 02
DEV : USB 1
UNSELECT
START
Track 03
Track 04
Track
05 START
CD
Ripping
Track 06
Track 07
CANCEL
Cancel Ripping
Enter
REPEAT
Repeat
Note
- When the CD ripping being processed the player
will automatic in play mode.
- Only the Audio CD(CD DA) dics can be ripping.
Picture CD Playback
This feature lets you to copy audio files from disc to USB
device into MP3 format.
T
Track 01
CD Ripping
Open the dics tray.
Off
Track 01
1. Select the desired folder.
2. Press the π/† buttons to select a Picture file in the clips menu and then press the ENTER button.
3. Press the INFO button on the remote control to select the menu you want to view and then press the ENTER button.
ALBUM
Play
Off
Track 01
Place the Audio CD(CD DA) disc on
the tray, and close the tray.
00:00:00
T
Track 01
Track 02
DEV : SELECT
START
Track 03
Track 04
Track 05
Connect the USB device to the USB
port on the front of the unit.
Track 06
Track 07
PHOTO: 1 /215
ENTER
RETURN
Track 08
This screen will displayed.
Enter
REPEAT
Repeat
ENTER
1. To Select DISC
With the unit in Stop mode, Press the π/† buttons to
select DISC. To Select DEV (storage media device)
Press the ® button to select the DEV (storage media
device) menu, then press the ENTER button.
Press the π/† buttons to select USB, then press the ENTER button
Stop
Note
- Press the STOP button to return to the clips menu.
- When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu.
ENTER
Off
Disc Track 01
T
00:00:00
USB
Track 01
Track 02
DEV : SELECT
START
Track 03
Track 04
Track 05
Track 06
RETURN
Rotation
Track 07
Track 08
Enter
Menu
2. Press the π/† buttons to select SELECT, then press the
ENTER button to marked all files to be copying.
- To unmarked copying all files press the ENTER button
again.(UNSELECT Menu)
- If you want to marked several files to be copying, press the
√ button, then press the ENTER button on the selected file.
24_ advance functions
RETURN
: Each time the ENTER button is pressed, the picture rotates 90 degrees clockwise.
Zoom
: Press the π/† buttons to select the part of the
screen you want to zoom in on.
Press the ENTER button. Each time the ENTER button is pressed, the picture is enlarged up to 2X. Slide Show
•
: The unit enters slide show mode.
• Before beginning the Slide Show, the picture interval must
be set.
: When this icon is selected and ENTER is pressed, the pictures change automatically with about a 6 second interval.
•
: The pictures change automatically with about a 12 second interval.
•
: The pictures change automatically with about a 18 second interval.
● advance functions
•
CD-R JPEG Disc
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
- The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special characters (. / = +).
- Only a consecutively written multi-se ssion disc can be played.If there is a blank segment in the multi-session disc, the disc can be played only up to the blank segment.
- A maximum of 3000 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can be played automatically.
- Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG files in 500 folders can be played
English _25
changing setup menu
Using the Setup Menu
The Setup menu lets you customize your DVD player by
allowing you to select various language preferences, set
up a parental level, even adjust the player to the type of television screen you have.
1. With the unit in Stop mode, press the MENU button on the remote control.Use the π/† buttons to select Setup, then press the ® or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
Parental Setup :
®
®
DivX(R) Registration
Enter
Return
®
Menu
n Language Setup: Setup of the Language.
n Audio Setup : Setup of the Audio Options.
n Display Setup : Setup of the Display Options. Use to select which type of screen you want to watch and sev eral display options.
n Parental Setup : Setup of the Parental Level. Allows users to set the level necessary to prevent children from viewing unsuitable movies such as those with violence, adult subject matter, etc.
n DivX(R) Registration : Please use the Registration code to register this player with the DivX(R) Video On Demand format.To learn more go to www.divx.com/vod.
Setting Up the Language
Features
If you set the player menu, disc menu, audio and subtitle
language in advance, they will come up automatically every
time you watch a movie.
Using the Player Menu Language
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
3. Press the π/† buttons to select Language Setup, then press the ® or ENTER button.
4. Press the π/† buttons to select Player Menu, then press the ® or ENTER button.
5. Press the π/† buttons to select the desired language, then press the ® or ENTER button.
- The language is selected and the screen returns to Language Setup menu.
- To make the setup menu disappear, press the MENU button.
Using the Disc Menu Language
This function changes the text language only on the disc
menu screens.
2. Press the π/† buttons to access the different features. Press the ® or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press the MENU button again.
Note
Depending on the disc, some Setup Menu selections may not work.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
3. Press the π/† buttons to select Language Setup, then press the ® or ENTER button.
4. Press the π/† buttons to select Disc Menu, then press the ® or ENTER button.
5. Press the π/† buttons to select the desired language, then press the ® or ENTER button.
If the selected language is not recorded on the disc, the original pre-recorded language is selected.
The language is selected and the screen returns to Language Setup menu.To make the setup menu disap pear, press the MENU button.
Language SetUP
26_ changing setup menu
Using the DivX Subtitle Language
Using the Audio Language
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
3. Press the π/† buttons to select Language Setup,‑then press the ® or ENTER button.
4. Press the π/† buttons to select DivX Subtitle, then press
the ® or ENTER button.
5. Press the π/† buttons to select the desired ‑language, then press the ® or ENTER button.The language is selected and the screen returns to Language Setup menu.To make the setup menu disappear, press the
MENU‑button.
Language SetUP
Language SetUP
Player Menu
: English
Audio
: English
Disc Menu
Subtitle
DivX Subtitle
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
3. Press the π/† buttons to select Language Setup,‑then press the ® or ENTER button.
4. Press the π/† buttons to select Subtitle, then press the ® or ENTER button.
5. Press the π/† buttons to select the desired ‑language, then press the ® or ENTER button.
- Select “Automatic” if you want the subtitle language to be the same as the language selected as the audio language.
‑ Some discs may not contain the language you select as your initial language; in that case the disc will use its original language setting.The language is selected and the screen returns to setup menu.To make the setup menu disappear, press the MENU button.
: English
√ Unicode
Western
Setting Up the Audio
Options
Audio Options allows you to setup the audio device
and sound status settings depending on the audio
system in use.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
3. Press the π/† buttons to select Audio Setup, then press the ® or ENTER button.
4. Press the π/† buttons to select the desired item, then press the ® or ENTER button.
Language Setup
Audio Setup
®
®
Display Setup
®
Parental Setup :
DivX(R) Registration
®
®
Language SetUP
AUDIO SETUP
Dolby Digital Out
:PCM
MPEG-2 Digital Out
: PCM
Dynamic Compression :On
PCM Down Sampling :On
Output Channel
: 2Ch
Speaker setup
®
Power On Music :On
English _27
● changing setup menu
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
3. Press the π/† buttons to select Language Setup, then press the ® or ENTER button.
4. Press the π/† buttons to select Audio, then press the ® or ENTER button.
5. Press the π/† buttons to select the desired language, then press the ® or ENTER button.
Select “Original” if you want the default soundtrack
language to be the original language the disc is recorded in.If the selected language is not recorded on the disc,the original pre-recorded language is selected.The language is selected and the screen returns to Language Setup menu.To make the setup menu disappear, press the
MENU button.
changing setup menu
❶ Dolby Digital Out
- PCM : Converts to PCM(2CH) audio.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
- Bitstream : Outputs Dolby Digital or DTS via the digital
output. Select Bitstream when connecting to a
Dolby Digital or DTS Decoder.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc. ❷ MPEG-2 Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream (5.1CH Surround Sound Speaker Setup
or 8CH). Select Bitstream when using the Digital Audio 1. With the unit in Stop mode, press the MENU button.
Output.
❸ Dynamic Compression
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
- On : To select dynamic compression.
- Off : To select the standard range.
player is not 96KHz compatible. In this case, the player is 96KHz compatible. In this case, all signals will be output without any changes.
AUDIO SetUP
❺ Output Channel
Dolby Digital Out
:PCM
MPEG-2 Digital Out
: PCM
Dynamic Compression :On
PCM Down Sampling :On
Output Channel
: 5.1Ch
Speaker setup
®
S etup
Power On Music :On
• 2Ch : Select this when using 2 channel connection
only.
• 5.1 Ch : Select this when using 5.1 Channel
connection.
 To make The Speaker Setup menu appear,
select output channel to 5.1 Ch. ➏ Speaker Setup
❼ Power On Music
SPEAKER SETUP
Small
This menu is used to activate or deactivate the opening sound when you turn on the DVD player.
- On : To turn On Start up music.
- Off : To turn Off Start up music.
Test
S etup Small
Small
On
Small
User
Small
Note : • Even when PCM Down sampling is Off Note
To make the setup menu disappear, press the MENU
button.
• Some discs will only output down sampled audio through the digital outputs.
• To make the Setup menu disappear, press the
MENU button.
• There is no analog audio output when you play a
DTS sound disc. 28_ changing setup menu
5. Press the π/†/√/® buttons to select the desired item, then press the ENTER button to set the speaker.
 To make the setup menu disappear, press the MENU
button.
96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
4. Press the π/† buttons to select Speaker Setup, then press the ® or ENTER button.
- On : Select this when the Amplifier connected to the 3. Press the π/† buttons to select Audio Setup, then press the ® or ENTER button.
❹ PCM Down Sampling
The default settings : FRONT L, R (Small),
CENTER (Small), SURROUND (Small).
Select the size of the speakers to be connected.
Language Setup
®
Audio Setup
®
❶ Front (FL, FR)
Parental Setup :
❷ Center
DivX(R) Registration
Setting up Test
To make the Setup menu disappear or return to menu
screen during set up, press RETURN button.
• The subwoofer test output signal is lower
- 4:3 Letter Box : Select when you want to see
the total 16:9 ratio screen DVD supplies, even though you have a TV with a 4:3
ratio screen. Black bars will appear at the top
and bottom of the screen.
- 4:3 Pan&Scan : Select this for conventional
size TVs when you want to see the central portion of the 16:9 screen. (Extreme left and right
side of movie picture will be cut off.)
- 16:9 Wide : You can view the full 16:9 picture on your wide screen TV.
DISPLAY SetUP
TV Aspect
√4:3 Letter Box
Screen Message 4:3 Pan&Scan
Black Level
16:9 Wide
: I-SCAN
❹ TV System
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input, you
must choose “PAL”. When you choose “PAL”,
Interlace output format is PAL 60 Hz output.
registered by PHILIPS Corporation.
• If your TV system only has NTSC, input you
must choose “NTSC ”.
• If you set Front (L, R) “Small”, LFE
(Subwoofer) is set “On” automatically.
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
3. Press the π/† buttons to select Display Setup, then press the ® or ENTER button.
4. Press the π/† buttons to select the desired item, then press the ® or ENTER button.
: Auto
Video Output
❸ Black Level
Adjusts the brightness of the screen.(On or Off) It
does not function in PAL mode.
• The MPEG Multichannel logo is a trademark
Display options enable you to set various video functions of
the player.
TV System
❷Screen Messages
Use to turn on-screen messages On or Off.
than the other speakers.
Setting Up the Display
Options
®
❶ TV Aspect
Depending on a type of television you have, you
may want to adjust the screen setting (aspect ratio).
- None: If you do not connect a center speaker,
select this.
- Large: Normally select this.
- Small: When the sound distorts, select this.
This activates the Dolby Digital bass redirection circuitry and outputs the bass frequencies of the center
speaker from other speakers.
❸ Surround (SL, SR)
- None: If you do not connect a center speaker,
select this.
- Large (Rear/Side): Normally select either of
these according to the rear speaker’s position.
- Small (Rear/Side): When the sound ditorts or
the surround sound effects are dificult to hear,
select either of these according to the rear
speaker’s position.
This activates the Dolby Digital bass rediretion
circuitry and outputs the bass frequencies of
the rear speaker from other speakers.
The test output signals come clockwise starting from the
Front Speaker (L). Adjust Channel Balance so that speakers output equally in your room.
FRONT(L) ➞ CENTER ➞ SUBWOOFER ➞ FRONT(R) ➞
SURROUND(R) ➞ SURROUND(L)
®
®
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input,
you must choose “NTSC”.
• If your TV system only has PAL input, you must choose “PAL ”.
- Auto
DISPLAY SetUP
TV Aspect
: 4:3 L-Box
Screen Messages
Black Level
TVSystem
System
TV
: On
: Off
NTSC
: PAL
√ PAL
Auto
Video Output
Setup
Enter
Return
Menu
English _29
● changing setup menu
- Large: Normally select this.
- Small: When the sound distorts or the suround sound
effects are difficult to hear, select this.
This activates the Dolby Digital bass redirec
tion circuitry and outputs the bass frequencies of
the speaker from the subwoofer.
Display Setup
changing setup menu
❺ Video Output
Select Video Output.
- I-SCAN : Select when you want to use Component Interlace Out.
- P-SCAN : Select when you want to use Component Progressive Out.
Setting Up the Parental
Control
• If you press the VIDEO SEL. button, Video output mode is changed in regular sequence in no disc mode. (I-SCAN ➞ P-SCAN)
• If the Yes/No selection in the Display Setup sub Menu is not made within 10 seconds, the screen returns to the previous menu.
DISPLAY SetUP
TV Aspect
: 4:3 L-Box
Screen Messages
: On
Black Level
: Off
TV System
Video Output
The Parental Control function works in conjunction
with DVDs that have been assigned a rating, which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
Setting Up the Rating Level
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
I-SCAN
√ P-SCAN
• Consult your TV User’s Manual to find
out if your TV supports Progressive Scan. If
Progressive Scan is supported, follow the TV User’s
Manual regarding Progressive Scan settings in the
TV’s menu system.
• If Video Output is set incorrectly, the screen may be
blocked.
• When the resolution is changed during playback,
it may take a few seconds for a normal image to
appear.
3. Press the π/† buttons to select Parental Setup, then press the ® or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
4. Press the π/† buttons to select Rating Level, then press the ® or ENTER button.
PARENTAL SetUP
Rating Level
: Kids Safe
Change Password
5. Enter your password, Press the π/† button to fill the blank box, then press the ENTER button to insert the number.
- By default, password‑is set to 0000.
- Please Change password to other than 0000 to parental control function activated.
PARENTAL SetUP
Rating Level
: Kids Safe
Change Password
Enter Password
0
Enter
30_ changing setup menu
Return
Menu
6. Press the π/† buttons to select the Rating Level you want, then press the ® or ENTER button.
e.g) Setting up in Kids Safe.
PARENTAL SetUP
Rating Level
√ Kids Safe
Change Passwor Level 2
Level
Level
Level
Level
3
4
5
6
5. Press the π/† button to fill the blank box, then press the ENTER button to insert the number. Enter your new pass
word again.
PARENTAL SetUP
Rating Level
:Kids Safe
Change Password
Enter Password
Enter
To make the setup menu disappear, press the MENU
button. For example, if you select up to Level 6, discs
that contain Level 7,8 will not play.
Return
Menu
PARENTAL SetUP
Rating Level
:Kids Safe
Change Password
Enter New Password
0
Changing the Password
Enter
1. With the unit in Stop mode, press the MENU button.
2. Press the π/† buttons to select Setup, then press the ® or ENTER button.
Language Setup
®
Audio Setup
®
Display Setup
Return
Menu
Note
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
®
Parental Setup :
®
DivX(R) Registration
®
3. Press the π/† buttons to select Parental Setup, then press the ® or ENTER button. The Enter Password screen appears. Enter your password.
Language Setup
®
Audio Setup
®
Display Setup
®
Parental Setup :
®
DivX(R) Registration
®
4. Press the π/† button to select Change Password, then press the ® or ENTER button. Enter your new password again.
PARENTAL SetUP
Rating Level
:Kids Safe
Change Password
English _31
● changing setup menu
0
reference
Firmware upgrade
Introduction
Samsung will often support the software upgrade to
improve the performance of this unit to the latest status, through Samsung Internet Site (www.samsung.
com).
Because the specially new mpeg4 codec continues and
it is appearing. What improvements are made depends
on the upgrade software you are using as well as the
software that your DVD-player contained before the
upgrade.
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or CDRW disc, using the following settings:
1. You have to download a new file through Download Center
of Samsung Internet Site (www.samsung.com).
2. Write the file to Disc using CD-RW of your computer.
Note
- File System CD-ROM ISO Level
- Character set ISO 9660
- Finalized, single session
- Write speed low
Upgrade procedure
1. Open the disc tray. Place the disc on the tray. Close the
tray. The Firmware upgrade screen appears.
071208.VD.B.P480KXEG
0801023.VD.B.P480KXEG
Firmware upgrade
appears on the display
32_ reference
2. Press the √/® buttons to select Total, then press the
ENTER button.
071208.VD.B.P480KXEG
0801023.VD.B.P480KXEG
Firmware upgrade starts
- In the middle of the writing, the tray will open automatically. After taking out the disc, please wait for about 2 minutes.
- If the unit was succesfully updated, the unit will turn off and on after closing the tray automatically. When the unit turns on, this screen will display.
3. Press the π/† buttons to select the desired language, and then press the ENTER button.
Note
- If the “Select Menu Language” doesn’t appear, please contact to “Samsung Service Center”.
- Do not press any button and unplug the power cord during upgrade.
- The upgrade procedure may change, refer to the web site (www.samsung.com).
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Problem
Disc does not play.
• Check the batteries in the remote control. They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes
to drain the microprocessor inside the remote control to reset it. Reinstall
batteries and try to operate the remote control again.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
Page
P3
P5
5.1 channel sound is
not being reproduced.
• 5.1 channel sound is reproduced only when the following conditions
are met. :
1) The DVD player is connected with the proper Amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
The icon
appears
on screen.
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
Disc Menu doesn’t appear.
• Check if the disc has a Menu.
Play mode differs from
the Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work properly if
the disc is not encoded with the corresponding function.
P26~31
The screen ratio cannot be changed.
• The Screen Ratio is fixed on your DVDs.
P29~30
No audio
• Make sure you have selected the correct Digital Output in the Audio
Options Menu.
P27~29
The screen is blocked
• Press the
button (in front panel) for more than 5 seconds under no disc
inside. All settings will revert to the factory settings.
Forgot password
button (in front panel ) for more than 5 seconds
• Press the
under no disc inside. All settings including the password will revert
to the factory settings. Don't use this unless absolutely necessary.
If you experience other
problems.
• Go to the contents and find the section of the instruction book that contains
the explanations regarding the current problem, and follow the procedure
once again.
• If the problem still cannot be solved, please contact your nearest authorized
service center.
The picture is noisy or
distorted
sure that the disc is not dirty or scratched.
• Make
the disc.
• Clean
P12~14
P27~29
P15
P30
P2
English _33
● reference
No operations can be
performed with the
remote control.
Action
reference
Specifications
Power Requirements
General
Disc
Video
Output
Audio
Output
AC 110-240 V ~ 50/60 Hz
Power Consumption
8W
Weight
1.6 Kg
Dimensions
430mm (W) X 203mm (D) X 37mm (H)
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
VCD : 12Cm
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
Composite Video
1 channel : 1.0 Vp-p (75 Ω load)
Component Video
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
5.1 channel
F/L,F/R,R/L,R/R,CT,S/W
*Maximum Output level
2 Vrms
Digital Audio Output
Coaxial (S/PDIF)
*Frequency Response
20Hz ~ 202kHz
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
34_ reference
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Region
North America
Latin America
Country
CANADA
MEXICO
U.S.A
ARGENTINE
BRAZIL
CHILE
NICARAGUA
HONDURAS
COSTA RICA
ECUADOR
EL SALVADOR
GUATEMALA
JAMAICA
PANAMA
PUERTO RICO
REP. DOMINICA
TRINIDAD & TOBAGO
VENEZUELA
COLOMBIA
BELGIUM
CZECH REPUBLIC
DENMARK
FINLAND
FRANCE
Europe
CIS
Asia Pacific
Middle East &
Africa
GERMANY
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
SPAIN
SWEDEN
U.K
EIRE
AUSTRIA
SWITZERLAND
RUSSIA
KAZAKHSTAN
UZBEKISTAN
KYRGYZSTAN
TADJIKISTAN
UKRAINE
LITHUANIA
LATVIA
ESTONIA
AUSTRALIA
NEW ZEALAND
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
THAILAND
TAIWAN
VIETNAM
TURKEY
SOUTH AFRICA
U.A.E
Contact Center 1-800-SAMSUNG(726-7864)
01-800-SAMSUNG(726-7864)
1-800-SAMSUNG(726-7864)
0800-333-3733
0800-124-421, 4004-0000
800-SAMSUNG(726-7864)
00-1800-5077267
800-7919267
0-800-507-7267
1-800-10-7267
800-6225
1-800-299-0013
1-800-234-7267
800-7267
1-800-682-3180
1-800-751-2676
1-800-SAMSUNG(726-7864)
0-800-100-5303
01-8000112112
02 201 2418
800-726-786 (800 - SAMSUNG)
70 70 19 70
030-6227 515
3260 SAMSUNG (€ 0,15/Min)
08 25 08 65 65 (€ 0,15/Min)
01805 - SAMSUNG(726-7864 € 0,14/Min)
06-80-SAMSUNG(726-7864)
800-SAMSUNG(726-7864)
02 261 03 710
0900-SAMSUNG (726-7864 € 0,10/Min)
815-56 480
0 801 801 881, 022-607-93-33
80820-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
902-1-SAMSU(72678)
0771-400 200
0845 SAMSUNG (7267864)
0818 717 100
0800-SAMSUNG(726-7864)
0800-SAMSUNG(726-7864)
8-800-555-55-55
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
8-800-502-0000
8-800-77777
8000-7267
800-7267
1300 362 603
0800 SAMSUNG (0800 726 786)
800-810-5858, 400-810-5858, 010-6475 1880
3698-4698
3030 8282, 1800 110011, 1-800-3000-8282
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG(726-7864)
1800-SAMSUNG(726-7864)
1800-29-3232, 02-689-3232
0800-329-999
1 800 588 889
444 77 11
0860-SAMSUNG(726-7864 )
800-SAMSUNG (726-7864), 8000-4726
Web Site
www.samsung.com/ca
www.samsung.com/mx
www.samsung.com/us
www.samsung.com/ar
www.samsung.com/br
www.samsung.com/cl
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com/latin
www.samsung.com.co
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.com/fi
www.samsung.com/fr
www.samsung.de
www.samsung.com/hu
www.samsung.com/it
www.samsung.com/lu
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/sk
www.samsung.com/es
www.samsung.com/se
www.samsung.com/uk
www.samsung.com/ie
www.samsung.com/at
www.samsung.com/ch
www.samsung.ru
www.samsung.com/kz_ru
www.samsung.com/kz_ru
www.samsung.ua
www.samsung.lt
www.samsung.com/lv
www.samsung.ee
www.samsung.com/au
www.samsung.com/nz
www.samsung.com/cn
www.samsung.com/hk
www.samsung.com/in
www.samsung.com/id
www.samsung.com/jp
www.samsung.com/my
www.samsung.com/ph
www.samsung.com/sg
www.samsung.com/th
www.samsung.com/tw
www.samsung.com/vn
www.samsung.com/tr
www.samsung.com/za
www.samsung.com/ae
ELECTRONICS
AK68-01768A(01)
Download PDF