Samsung | QM85D-BR | Samsung QM85D-BR Quick start guide

Reverse Side
1 Supplies power to the external sensor board or receives the light
sensor signal.
Quick Setup Guide
2 Connects to a source device using a HDMI cable or HDMI-DVI cable.
3 Connects to a PC using a DP cable.
- Obtain sharp picture quality when viewing UHD content at 30 Hz.
- The recommended resolution for the DP IN 3 (UHD 30Hz) port
is 1920 x 1080 @ 60 Hz. The resolution can be changed to the
optimal resolution of 3840 x 2160 @ 30 Hz, if required.
QM85D QM85D-BR
4 C
onnects to a PC using a DP cable.
- Obtain sharp picture quality when viewing UHD content at 60 Hz.
5 D
VI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
MAGICINFO IN: To use MagicInfo, make sure to connect the DP-DVI cable.
6 Connects to MDC using a LAN cable.
7 Receives the remote control signal via the external sensor board
and outputs the signal via LOOP OUT.
-- Recommended hours of use per day of this product is under 16 hours. If the product is used for longer than 16 hours a day, the warranty may be void.
-- The colour and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the
performance.
-- The MagicIWB S user guide can be downloaded from http://www.samsung.com/displaysolutions.
-- Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
8 Connects to MDC using an RS232C adapter.
- For details on how to use the MDC programme, refer to Help after
installing the programme. The MDC programme is available on
the website.
9 Connects to a USB device when upgrading software.
0 Connects to a source device using a D-SUB cable.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
! Connects to the audio of a source device.
@ Receives sound from a PC via an audio cable.
BN68-07440J-00
Control Panel
Checking the Components
Contact the vendor where you purchased the product if any
components are missing.
Quick Setup Guide
Regulatory guide
Warranty card
(Not available in some locations)
-
+
+
Power cord
Batteries
(Not available in some locations)
Touch Pen (1EA)
(QM85D-BR Model Only)
QM85D-BR-QSG-India_BN68-07440J-00.indd 1
DP cable
Solutions
Issues
The screen keeps
switching on and off.
Check the cable connection between the
product and PC, and ensure the connection is
secure.
The screen is too bright.
Adjust Brightness and Contrast.
The screen is too dark.
No Signal is displayed
on the screen.
Check that the product is connected correctly
with a cable.
There is no image on
the screen and the
power LED blinks
every 0.5 to 1 second.
The product is in power-saving mode.
There is no sound.
Check the connection of the audio cable or
adjust the volume.
Not Optimum Mode
is displayed.
1 P ower on the product.
If you press the button when the product is turned on, the control
menu will be displayed.
- To exit the OSD menu, press and hold the panel key for at least one
second.
2 M
ove to the upper or lower menu. You can also adjust the value of an
option.
3 M
ove to the left or right menu.
- You can adjust the volume by moving the panel key left or right
when the control menu is not displayed.
Remote Control
Issues
Check that the device connected to the
product is powered on.
MagicInfo Software DVD
-
Troubleshooting Guide
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
The images on the
screen look distorted.
The screen is not clear.
The screen is blurry.
Check the cable connection to the product.
Adjust Coarse and Fine.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
4 Speaker
5 Remote sensor
Press a button on the remote control pointing at the sensor on the
front of the product to perform the corresponding function.
- Using other display devices in the same space as the remote
control of this product can cause the other display devices to be
inadvertently controlled.
This message is displayed when a signal
from the graphics card exceeds the product’s
maximum resolution and frequency.
The screen appears
unstable and shaky.
Check that the resolution and frequency of the
PC and graphics card are set within a range
compatible with the product. Then, change the
There are shadows or
ghost images left on the screen settings if required by referring to the
Additional Information on the product menu
screen.
and the Standard Signal Mode Table.
Solutions
Press any key on the keyboard or move the
mouse to return to the previous screen.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to
the maximum level, adjust the volume on
your PC sound card or software programme.
The remote control does Make sure that the batteries are correctly in
not work.
place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
2015-09-02
3:52:49
Connecting to a PC
Connecting to an Audio System
RGB IN
AUDIO OUT
Specifications
Model Name
QM85D
QM85D-BR
Size
214 cm
214 cm
Display area
1872.0 mm (H) x 1053.0 mm (V)
1872.0 mm (H) x 1053.0 mm (V)
Dimensions (W x H x D)
1903.4 x 1090.5 x 105.1 mm
1949 x 1130 x 128.8 mm
Weight (without stand)
55.5 kg
81.2 kg
Panel
RGB / DVI / HDMI / AUDIO IN
DVI IN / MAGICINFO IN
Connecting the LAN Cable
Horizontal Frequency
30 - 81 kHz, 30 - 134 kHz (DisplayPort), 30 - 90 kHz (HDMI)
Vertical Frequency
48 - 75 Hz, 56 - 75 Hz (DisplayPort), 24 - 75 Hz (HDMI)
Synchronization
RGB / DVI / HDMI / AUDIO IN
RJ45
RGB Analog, DVI (Digital Visual Interface) Compliant Digital RGB
Resolution
HDMI IN 1, HDMI IN 2, HDMI IN 3
Connecting to MDC
Optimum resolution
1920 x 1080 @ 60 Hz, 3840 x 2160 @ 60 Hz (DisplayPort1, DisplayPort2)
Maximum resolution
1920 x 1080 @ 60 Hz, 3840 x 2160 @ 30 Hz (HDMI1, HDMI2, HDMI3, DisplayPort3)
Maximum Pixel Clock
148.5 MHz (Analog, Digital), 533 MHz (DisplayPort), 297 MHz (HDMI)
Power Supply
AC 100 to 240 VAC (+/- 10%), 60 / 50 Hz ± 3 Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
RGB / DVI / HDMI / AUDIO IN
HDMI IN 1, HDMI IN 2, HDMI IN 3
Operating
Temperature: 0 ˚C – 40 ˚C (32 ˚F – 104 ˚F)
Humidity: 10% – 80%, non-condensing
Storage
Temperature: -20 ˚C – 45 ˚C (-4 ˚F – 113 ˚F)
Humidity: 5% – 95%, non-condensing
Environmental
considerations
-- This device is a Class A digital apparatus.
DP IN 1 (UHD 60Hz),
DP IN 2 (UHD 60Hz), DP IN 3 (UHD 30Hz)
(For India Only)
This product is RoHS compliant.
For more information on safe disposal and recycling visit our
website www.samsung.com/in or contact our Helpline numbers 18002668282, 180030008282.
Contact SAMSUNG WORLD WIDE
Connecting to a Video Device
Web site: http://www.samsung.com
INDIA
1800 3000 8282 - Toll Free
1800 266 8282 - Toll Free
HDMI IN 1, HDMI IN 2, HDMI IN 3
RGB / DVI / HDMI / AUDIO IN
HDMI IN 1, HDMI IN 2, HDMI IN 3
QM85D-BR-QSG-India_BN68-07440J-00.indd 2
2015-09-02
3:52:51
Download PDF