Samsung | QM98F | Samsung QM98F Quick start guide

Reverse Side
1Connects to MDC using an RS232C adapter.
RS232C IN
Quick Setup Guide
2DVI: Connects to a source device using a DVI cable or HDMI-DVI cable.
PC: Connects a D-SUB cable (via a DVI-RGB adapter) or a DVI-RGB
cable to a PC.
MAGICINFO IN: To use MagicInfo, make sure to connect the DP-DVI
cable.
DVI/PC/
MAGICINFO IN
HDMI IN 4
QM98F
3Connects to a source device using a HDMI cable or HDMI-DVI cable.
-O
btain sharp picture quality when viewing UHD content at 30Hz.
HDMI IN 3
4Connects to a PC using a DP cable.
- Obtain sharp picture quality when viewing UHD content at 60Hz.
HDMI IN 2
5Connects to MDC using a LAN cable.
6Connects to MDC using an RS232C adapter.
HDMI IN 1
7Supplies power to the external sensor board or receives the light
sensor signal.
DP IN 2
(UHD 60Hz)
8Receives the remote control signal via the external sensor board
and outputs the signal via LOOP OUT.
RS232C
OUT
IR IN
DP IN 1
(UHD 60Hz)
SERVICE
DVI/PC/
HDMI/
AUDIO IN
RJ45
IR OUT
−−The colour and the appearance may differ depending on the product, and the
specifications are subject to change without prior notice to improve the performance.
−−Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
AUDIO OUT
9Connects to a USB device when upgrading software.
0Receives sound from a PC via an audio cable.
!Connects to the audio of a source device.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
BN68-07823A-00
Control Panel
Checking the Components
Troubleshooting Guide
Contact the vendor where you purchased the product if any
components are missing.
The pictures may look different from the actual components.
Warranty card
(Not available in some locations)
MagicInfo Software
DVD
Solutions
Issues
Solutions
The screen keeps
switching on and off.
Check the cable connection between
the product and PC, and ensure the
connection is secure.
There is no image on
the screen and the
power LED blinks
every 0.5 to 1 second.
The product is in power-saving mode.
No Signal is displayed Check that the product is connected
on the screen.
correctly with a cable.
Speaker
Quick Setup Guide
Issues
Check that the device connected to the
product is powered on.
,
Depending on the type of external device,
the screen may not display properly. In
this case, connect it with the HDMI Hot
Plug function turned On.
1 S
pacer logo
Do not pull on the spacer logo using force. The logo may tear or
break off.
Power cord
RS232C(IN) adapter
Batteries
(Not available in some locations)
HOLDER-CABLE
Remote Control
2 R
emote sensor
Press a button on the remote control pointing at the bottom of
the product face to perform the function. The remote control
sensor is located on the bottom of the product.
- Using other display devices in the same space as the remote
control of this product can cause the other display devices to
be inadvertently controlled.
To use remote/eco sensor, make sure the sliding panel key is
protruding from the bottom of the product.
3 P
anel Key
To use the panel key, make sure the sliding panel key is not
protruding from the bottom of the product.
The images on the
Check the cable connection to the
screen look distorted. product.
The screen appears
unstable and shaky.
There are shadows or
ghost images left on
the screen.
QM98F_INDIA_QSG_BN68-07823A-00.indd 1
Picture quality of the
product is different
from the dealer
shop where it was
purchased.
Use an HDMI cable to obtain highdefinition (HD) picture quality.
The remote control
does not work.
Make sure that the batteries are correctly
in place (+/-).
Check if the batteries are flat.
Not Optimum Mode is This message is displayed when a
displayed.
signal from the graphics card exceeds
the product’s maximum resolution and
frequency.
Refer to the Standard Signal Mode Table
and set the maximum resolution and
frequency according to the product
specifications.
Check that the resolution and frequency
of the PC and graphics card are set within
a range compatible with the product.
Then, change the screen settings if
required by referring to the Additional
Information on the product menu and the
Standard Signal Mode Table.
Press any key on the keyboard or move the
mouse to return to the previous screen.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon
signs switched on in the vicinity.
A beeping sound is
heard when my PC is
booting.
When I try to change
the PC resolution, a
message The
defined resolution
is not supported.
appears.
If a beeping sound is heard when your PC
is booting, have your PC serviced.
The message The defined resolution
is not supported. appears if the input
source resolution exceeds the maximum
resolution of the display.
To resolve the issue, change the PC
resolution to a resolution supported on
the display.
2017-11-09 오후 6:18:55
HDMI IN 1, HDMI IN 2, HDMI IN 3, HDMI IN 4
DVI/PC/HDMI/AUDIO IN
Connecting to a PC
Connecting to an Audio System
HDMI IN 1, HDMI IN 2, HDMI IN 3, HDMI IN 4
HDMI IN 1, HDMI IN 2, HDMI IN 3, HDMI IN 4
DP IN 1 (UHD 60Hz), DP IN 2 (UHD 60Hz)
DP IN 1 (UHD 60Hz), DP IN 2 (UHD 60Hz)
DVI/PC/MAGICINFO IN
DVI/PC/MAGICINFO IN
DVI/PC/HDMI/AUDIO IN
DVI/PC/HDMI/AUDIO IN
Specifications
Model Name
QM98F
AUDIO OUT
RS232C IN
Panel
RS232C OUT
Power Supply
Connecting to MDC
RS232C IN
RJ45
Size
247.7 cm
Display area
2158.848 mm (H) x 1214.352 mm (V)
AC100-240V~ 50/60Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Operating
Temperature : 0 °C – 40 °C (32 °F – 104 °F)
Humidity : 10% – 80%, non-condensing
Storage
Temperature : -20 °C – 45 °C (-4 °F – 113 °F)
Humidity : 5% – 95%, non-condensing
Environmental
considerations
- This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to
take adequate measures.
- For detailed device specifications, visit the Samsung Electronics website.
- The PVC Free (except for accessory cables) logo is the self-declared trademark of Samsung.
* Accessory cables: signal cables and power cords
RS232C OUT
RS232C OUT
HDMI IN 1, HDMI IN 2, HDMI IN 3, HDMI IN 4
HDMI IN 1, HDMI IN 2, HDMI IN 3, HDMI IN 4
DVI/PC/HDMI/AUDIO IN
DVI/PC/HDMI/AUDIO
ININ
DCJ: AV/COMPONENT
RJ45
RS232C IN
RJ45
HUB
Warning! Important Safety Instructions
(Please read the appropriate section that corresponds to the marking on your Samsung product before attempting to install the product.)
RS232C OUT
RS232C OUT
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
DVI/PC/MAGICINFO
IN IN
DCJ: DVI/HDMI/AUDIO
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). THERE ARE NO USER SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED
PERSONNEL.
DVI/PC/MAGICINFO IN
DVI/PC/HDMI/AUDIO IN
DCJ: AV/COMPONENT IN
RJ45
RJ45
DVI/PC/HDMI/AUDIO IN
HUB
RS232C OUT
DCJ: DVI/HDMI/AUDIO IN
Connecting to a Video Device
HDMI IN 1, HDMI IN 2, HDMI IN 3, HDMI IN 4
RJ45
DVI/PC/HDMI/AUDIO IN
HUB
For details on how
to use the MDC programme, refer to Help after
installing the programme.
The MDC programme is available on the website.
»» If your equipment uses an AC adapter:
- Only use the AC adapter with your product by
Samsung.
- Do not use the power cord with other products.
»» Do not install this equipment in a confined space such as a case
or similar.
»» The slots and openings in the cabinet and in the back or bottom
are provided for necessary ventilation. The slots and openings
must never be blocked or covered.
»» The product should be located away from heat sources such as
radiators, heat registers, or other products that produce heat.
This symbol indicates that high voltage is present
inside. It is dangerous to make any kind of contact
with any internal part of this product.
This symbol indicates that this product has included
important literature concerning operation and
maintenance.
»» Do not place a water containing vessel (vases etc.) on this
apparatus, as this can result in a risk of fire or electric shock.
(Apparatus shall not be exposed to dripping or splashing)
»» The apparatus must be connected to an earthed MAINS socketoutlet (Class l Equipment only). Or Use only a properly grounded
plug and receptacle (Class l Equipment only).
»» To disconnect the apparatus from the mains, the plug must be
pulled out from the mains socket, therefore the mains plug shall
be readily operable.
»» As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off this
unit by POWER.
This product is RoHS compliant.
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger,
headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent
possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from
other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers
-1800 40 SAMSUNG(1800 40 7267864) (Toll-Free)
AUDIOINOUT
HDMI
1, HDMI IN 2, HDMI IN 3, HDMI IN 4
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Tel. 1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
www.samsung.com/in/support
DP IN 1 (UHD 60Hz), DP IN 2 (UHD 60Hz)
DVI/PC/MAGICINFO IN
QM98F_INDIA_QSG_BN68-07823A-00.indd
2
2017-11-09 오후 6:18:58
Download PDF

advertising