advertisement
▼
Scroll to page 2
of 144
HP-T4254 HP-T5054 PLASMA DISPLAY Owner’s Instructions Register your product at www.samsung.com/global/register Record your Model and Serial number here for future reference. ▪ Model _______________ ▪ Serial No. _______________ BN68-01192F-02Eng-1.indd 1 2007-02-26 ソタネト 3:16:18 Important Warranty Information Regarding Television Format Viewing Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week. Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the above guidelines can cause uneven aging of PDP Displays that leave subtle, but permanent burned-in ghost images in the PDP picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On PDP models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a result of format selection and use, as well as burned-in images, are not covered by your Samsung limited warranty. © 2007 Samsung Electronics Co., Ltd. All rights reserved. . English - 2 BN68-01192F-02Eng-1.indd 2 2007-02-26 ソタネト 3:16:18 User Instructions Screen Image retention Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, refer to page 26 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still image. Altitude The PDP can only operate normally at heights under 6500ft. Heat on the top of the PDP TV The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product. The product is making a ‘cracking’ noise. A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit. Cell Defects The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product. Avoid operating the TV at temperatures below 5°C (41°F) A still image displayed too long may cause permanent damage to the PDP Panel. Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty. Afterimage on the Screen. Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a long time. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. English - 3 BN68-01192F-02Eng-1.indd 3 2007-02-26 ソタネト 3:16:19 Contents GENERAL INFORMATION CHANNEL CONTROL ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ List of Features ..............................................................5 Accessories....................................................................5 Viewing the Control Panel .............................................6 Viewing the Connection Panel .......................................7 Remote Control..............................................................8 Installing Batteries in the Remote Control ..................... 9 CONNECTIONS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Connecting VHF and UHF Antennas ............................. 9 Connecting Cable TV ...................................................10 Connecting a VCR ....................................................... 11 Connecting an S-VHS VCR ......................................... 11 Connecting a Camcorder .............................................12 Connecting a DVD Player/Set-Top Box ....................... 12 Connecting a DVD Player/Set-Top Box via HDMI ....... 13 Connecting a DVD Player/Set-Top Box via DVI........... 13 Connecting a Digital Audio System.............................. 14 Connecting an Amplifier/DVD Home Theater .............. 14 Connecting a PC..........................................................14 Turning the TV On and Off ...........................................15 Plug & Play Feature .....................................................15 Changing Channels .....................................................17 Adjusting the Volume ...................................................18 Viewing the Display .....................................................18 Viewing the Menus ......................................................18 Memorizing the Channels ............................................19 Setting Up Your Remote Control.................................. 20 To Select the Source ....................................................25 To Edit the Input Source Name .................................... 25 PICTURE CONTROL ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Using Automatic Picture Settings................................. 26 Digital Noise Reduction ...............................................27 Changing the Screen Size ...........................................28 Configuring Detailed Settings on the Picture ............... 29 Active Color..................................................................30 DNIe (Digital Natural Image engine) ............................ 30 Selecting the Film Mode ..............................................31 Setting the Blue Screen Mode .....................................31 Setting the HDMI Black Level ...................................... 31 Viewing Picture-in-Picture ............................................32 Freezing the Current Picture........................................33 SOUND CONTROL ■ ■ ■ ■ ■ ■ ■ ■ ■ Using Automatic Sound Settings ................................. 34 Customizing the Sound................................................34 Setting the TruSurround XT .........................................35 Choosing a Multi-Channel Sound (MTS) Track - Digital .. 35 Choosing a Multi-Channel Sound (MTS) Track - Analog .. 36 Automatic Volume Control ...........................................36 Selecting the Internal Mute ..........................................36 Adjusting the Melody Sound ........................................37 Listening to the Sound of the Sub (PIP) Picture .......... 37 Symbols PC DISPLAY ■ ■ ■ ■ Using Your TV as a Computer (PC) Display ................ 43 Display Modes ............................................................ 43 Setting up the TV with your PC .................................... 44 Setting the Home Theater PC ...................................... 45 TIME SETTING ■ Setting the Time ........................................................... 46 FUNCTION DESCRIPTION OPERATION ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Selecting the Antenna .................................................. 38 Adding and Erasing Channels ..................................... 38 Setting Your Favorite Channels ................................... 39 Viewing the Channel Lists ........................................... 40 Setting the Default Channel List Mode ........................ 40 Labeling Channels ....................................................... 41 Fine Tuning Analog Channels ...................................... 41 Checking the Digital-Signal Strength ........................... 42 LNA (Low Noise Amplifier) ........................................... 42 Press One-Touch Button ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Selecting a Menu Language ........................................ 49 Using the Game Mode ................................................. 49 Viewing Closed Captions (On-Screen Text Messages) - Digital ....50 Viewing Closed Captions (On-Screen Text Messages) - Analog.. 51 Menu Transparency Level ........................................... 52 Setting the Light Effect ................................................. 52 Using the Energy Saving Feature ................................ 53 Preventing Screen Burn-in........................................... 53 Reducing the Effects of Screen Burn ........................... 54 Setting the Function Help ............................................ 54 Wall- mount adjustment (Sold separately) ................... 55 Upgrading the Software ............................................... 56 Using the V-Chip .......................................................... 56 About Anynet+ ■ ■ ■ ■ ■ ■ ■ What is Anynet+? ......................................................... 62 Connecting Anynet+ Devices ....................................... 62 Setting Up Anynet+ ...................................................... 63 Scanning and Switching between Anynet+ Devices .... 63 Recording .................................................................... 64 Listening through a Receiver ....................................... 65 Check Points before Requesting Service .................... 65 APPENDIX ■ Troubleshooting ........................................................... 66 ■ Installing the Wall Mount Kit......................................... 67 ■ How to assemble the Stand-Base (depending on the model) ........................................... 68 ■ Specifications............................................................... 68 ■ Dimensions (HP-T4254) .............................................. 69 ■ Dimensions (HP-T5054) .............................................. 70 ➢ Note English - 4 BN68-01192F-02Eng-1.indd 4 2007-02-26 ソタネト 3:16:19 General Information List of Features • • • • • Adjustable picture settings that can be stored in the TV’s memory. Automatic timer to turn the TV on and off. A special sleep timer. V-Chip function. Excellent Digital Interface & Networking : With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Set-Top Box needed. • Remote Control The supplied remote can be used to operate the TV as well as most DVD players, Set-top boxes, Cable Boxes and VCRs. • Excellent Picture Quality - DNIe technology provides life-like clear images. • SRS TruSurround XT - SRS TruSurround XT provides a virtual Dolby surround system. Accessories FAV .CH RET URN Please make sure the following items are included with your TV. If any items are missing, contact your dealer. Remote Control (BN59-00599A) / AAA Batteries (4301-000103) Power Cord (3903-000144) Owner’s Instructions / Quick Setup Guide Warranty Card / Registration Card / Safety Guide Manual Cover-Bottom / Screws (2ea) (Refer to page 68) Ferrite Core for Power Cord (3301-001110) Ferrite Core for Side-AV / S-VIDEO (3301-001305 ) Ferrite Core for Headphone (3301-001456) Cloth-Clean The following parts are sold separately and are available at most electronics stores. S-VIDEO Cable (BN39-00149A) HDMI Cable (BN39-00641A) HDMI/DVI cable (BN39-00643A) Component Cables (RCA) (BN39-00279A) PC Cable (BN39-00115A) PC Audio Cable (BN39-00061B) Optical Cable Antenna Cable (BN39-00333A) ➢ Ferrite Core (Power Cord, Audio/Video Cable, S-Video Cable, Headphone) The ferrite cores are used to shield the cables from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug. English - 5 BN68-01192F-02Eng-1.indd 5 2007-02-26 ソタネト 3:16:29 Viewing the Control Panel Buttons on the Lower-Right Part of the Panel The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control. ➢ The product color and shape may vary depending on the model. 1 SOURCE Toggles between all the available input sources (TV, AV1, AV2, S-Video1, S-Video2, Component1, Component2, PC, HDMI1, HDMI2, or HDMI3). 5 2 MENU Press to see an on-screen menu of your TV’s features. 3 + VOL – Press to increase or decrease the volume. In the onscreen menu, use the + VOL – buttons as you would use the ◄ and ► buttons on the remote control. 4 CH Press to change channels. In the on-screen menu, use the CH buttons as you would use the ▲ and ▼ buttons on the remote control. (ENTER) Press to confirm a selection. 6 POWER Press to turn the TV on and off. Power Indicator Blinks and turns off when the power is on and lights up in stand-by mode. Remote Control Sensor Aim the remote control towards this spot on the TV. 7 Speakers English - 6 BN68-01192F-02Eng-1.indd 6 2007-02-26 ソタネト 3:16:41 Viewing the Connection Panel Rear Panel Jacks Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players. For more information on connecting equipment, see pages 9-14. The product color and shape may vary depending on the model. audio inputs on your TV allow you to receive left and right audio from your DVI device. (Not compatible with PC) 1 POWER IN Connect the supplied power cord. 2 DIGITAL AUDIO OUT (OPTICAL) Connect to a Digital Audio component. 8 ANT 1 IN(AIR)/ANT 2 IN(CABLE) 75Ω Coaxial connector for Air/Cable Network. 3 AUDIO OUT (R/L) Audio outputs to external devices. 9 EX-LINK Connect this to the jack on the optional wall mount bracket. This will allow you to adjust the TV viewing angle using your remote control. 4 PC AUDIO IN Connect to the audio output jack on your PC. 5 PC IN Connect to the video output jack on your PC. 6 DVI IN (HDMI 1) (AUDIO-R/L) Connect to the DVI audio output jack of an external device. 0 AUDIO-R/L (AV IN 1) Audio inputs for external devices, such as a camcorder or VCR. ! S-VIDEO (AV IN 1) S-Video input for external devices with an S-Video output, such as a camcorder or VCR. 7 HDMI IN 1, 2 Connect to the HDMI jack of a device with HDMI output. @ VIDEO (AV IN 1) (Only HDMI 1 can support HDMI-DVI IN and PC.) Video input for external devices, such as a camcorder This input can also be used as a DVI connection with or VCR. separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection. # COMPONENT IN 1, 2 When using an optional HDMI/DVI adapter, the DVI analog Component video (Y/PB/PR) and audio (R-AUDIO-L) inputs. Side Panel Jacks Use the right side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game. The product color and shape may vary depending on the model. 1 HDMI IN 3 Connect to the HDMI jack of a device with HDMI output. ��������� 2 SERVICE For service only. 3 S-VIDEO IN 2 S-Video input for external devices with an S-Video output. 4 AV IN 2 Video and audio inputs for external devices. 5 HEADPHONE You can connect a set of headphones if you wish to watch a television program without disturbing other people in the room. English - 7 BN68-01192F-02Eng-1.indd 7 2007-02-26 ソタネト 3:16:42 Remote Control You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box. 1 POWER Turns the TV on and off. ( 2 NUMERIC BUTTONS Press to directly select a channel. 3 – Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “–” and “3”. 4 CH LIST Used to display Channel Lists on the screen. ) SOURCE Press to display all of the available video sources. a PRE-CH Tunes to the previous channel. b WISELINK Not available. c REC This remote can be used to control recording on Samsung recorders. (Refer to page 64) 5 ANTENNA Press to select “AIR” or “CABLE”. 6 VCR/DVD Functions - Rewind - Stop - Play/Pause - Fast/Forward 7 + VOL – Press to increase or decrease the volume. 8 MUTE Press to temporarily cut off the sound. 9 MENU Displays the main on-screen menu. 0 S.MODE Press to select the sound mode. ! RETURN Returns to the previous menu. @ P.MODE RETURN Press to select the picture mode. # CAPTION Controls the caption decoder. FAV.CH $ FAV.CH Press to switch to your favorite channels. % SLEEP Press to select a preset time interval for automatic shut off. ^ SRS Selects SRS TruSurround XT mode. & SET ➢ ➢ This is a special remote control for the visually impaired, and has Braille points on the POWER, Channel, Volume, STOP, and PLAY/PAUSE buttons. The performance of the remote control may be affected by bright light. Sets the remote to control your TV, VCR, Cable, DVD, or Set-Top Box. * TV/DVD/STB/CABLE/VCR Press to operate your TV, DVD, STB, CABLE (box), or VCR. Press to backlight the VOL, CH, and active source button (TV, DVD, CABLE, STB, VCR) on the remote. d CH Press to change channels. e EXIT Press to exit the menu. f UP▲/DOWN▼/LEFT◄/ RIGHT►/ENTER Use to select on-screen menu items and change menu values. g INFO Press to display information on the TV screen. h Anynet+ Runs the Anynet+ view functions and sets up Anynet+ devices. i STILL Press to stop the action during a particular scene. Press again to resume normal video. j P.SIZE Press to change the screen size. k PIP Picture-in Picture ON/OFF. l CH / Displays the available channels in sequence. (These buttons change channels in the PIP window only.) m MTS Press to choose stereo, mono or Separate Audio Program (SAP broadcast). n RESET When your remote does not work, change the batteries and press the RESET button for 2-3 seconds before use. English - 8 BN68-01192F-02Eng-1.indd 8 2007-02-26 ソタネト 3:16:48 Installing Batteries in the Remote Control 1 2 3 ➢ Lift the cover at the back of the remote control upward as shown in the figure. Install two AAA size batteries. ➢ Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment. ➢ Do not mix battery types, i.e. alkaline and manganese. Close the cover as shown in the figure. ➢ Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet (7m) from the TV. (Assuming typical TV usage, the batteries last for about one year.) If the remote control doesn’t work, check the following: 1. Is the TV power on? 2. Are the plus and minus ends of the batteries reversed? 3. Are the batteries drained? 4. Is there a power cut, or is the power cord unplugged? 5. Is there a special fluorescent light or a neon sign nearby? Connections Connecting VHF and UHF Antennas If your antenna has a set of leads that look like this, see “Antennas with 300 Ω Flat Twin Leads” below. If your antenna has one lead that looks like this, see “Antennas with 75 Ω Round Leads”. If you have two antennas, see “Separate VHF and UHF Antennas”. Antennas with 300 Ω Flat Twin Leads If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300 Ω twin flat leads, follow the directions below. 1 Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not supplied). Use a screwdriver to tighten the screws. 2 Plug the adaptor into the ANT 1 IN (AIR) or ANT 2 IN (CABLE) terminal on the back of the TV. ANT 1 IN (AIR) Antennas with 75 Ω Round Leads 1 Plug the antenna lead into the ANT 1 IN (AIR) or ANT 2 IN (CABLE) terminal on the back of the TV. ANT 1 IN (AIR) Separate VHF and UHF Antennas If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops). 1 Connect both antenna leads to the combiner. UHF VHF 2 Plug the combiner into the ANT 1 IN (AIR) or ANT 2 IN (CABLE) terminal on the bottom of the back panel. UHF VHF ANT 1 IN (AIR) English - 9 BN68-01192F-02Eng-1.indd 9 2007-02-26 ソタネト 3:16:51 Connecting Cable TV To connect to a cable TV system, follow the instructions below. Cable without a Cable Box 1 Plug the incoming cable into the ANT 2 IN(CABLE) terminal on the back of the TV. ➢ Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels. ANT 2 IN (CABLE) Connecting to a Cable Box that Descrambles All Channels 1 2 Find the cable that is connected to the ANT OUT terminal on your cable box. ➢ This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”. ANT IN ANT OUT Connect the other end of this cable to the ANT 2 IN(CABLE) terminal on the back of the TV. ANT 2 IN (CABLE) Connecting to a Cable Box that Descrambles Some Channels If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics stores.) 1 Find and disconnect the cable that is connected to the ANT IN terminal on your cable box. ➢ 2 ANT IN This terminal might be labeled “ANT IN”, “VHF IN” or simply, “IN”. Connect this cable to a two-way splitter. Incoming cable 3 Connect an Antenna cable between an OUTPUT terminal on the splitter and the IN terminal on the cable box. Incoming cable Splitter Splitter Cable Box 4 Connect an Antenna cable between the ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch. Incoming cable Splitter RF (A/B) Switch Cable Box 5 Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch. Incoming cable Splitter Cable Box 6 Connect the last Antenna cable between the OUT terminal on the RF (A/B) switch and the ANT 2 IN (CABLE) terminal on the rear of the TV. RF (A/B) Switch TV Rear Incoming cable Splitter ANT 2 IN (CABLE) RF (A/B) Switch After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.) English - 10 BN68-01192F-02Eng-1.indd 10 2007-02-26 ソタネト 3:16:56 Connecting a VCR Video Connection These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 9~10). Skip step 1 if you have not yet connected to an antenna or a cable system. 1 Unplug the cable or antenna from the back of the TV. 2 Connect the cable or antenna to the ANT IN terminal on the back of the VCR. 3 Connect an Antenna Cable between the ANT OUT terminal on the VCR and the ANT 1 IN(AIR) or ANT 2 IN (CABLE) terminal on the TV. 4 Connect a Video Cable between the VIDEO OUT jack on the VCR and the AV IN 1 [VIDEO] jack on the TV. 5 Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AV IN 1 [R-AUDIO-L] jacks on the TV. ➢ If you have a “mono” (non-stereo) VCR, use a Yconnector (not supplied) to hook up to the right and left audio input jacks of the TV. If your VCR is stereo, you must connect two cables. TV Rear Panel VCR Rear Panel 5 Audio Cable(Not supplied) 2 4 Video Cable(Not supplied) 3 Antenna cable(Not supplied) ➢ ➢ Each VCR has a different back panel configuration. When connecting a VCR, match the color of the connection terminal to the cable. S-Video Connection Your Samsung TV can be connected to the S-Video jack of a VCR. (This connection delivers a better picture when compared to the regular Video connection above.) 1 To begin, follow steps 1–3 in the previous section to connect the antenna or cable to your VCR and your TV. 2 Connect an S-Video Cable between the S-VIDEO OUT jack on the VCR and the AV IN 1 [S-VIDEO] jack on the TV. 3 Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AV IN 1 [R-AUDIO-L] jacks on the TV. TV Rear Panel VCR Rear Panel 3 Audio Cable (Not supplied) 2 S-Video Cable(Not supplied) 3 Antenna cable(Not supplied) An S-Video may be included with your VCR. (If not, check your local electronics store.) Each VCR has a different back panel configuration. When connecting a VCR, match the color of the connection terminal to the cable. ➢ ➢ English - 11 BN68-01192F-02Eng-1.indd 11 2007-02-26 ソタネト 3:17:01 Connecting a Camcorder The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR 1 2 Connect a Video Cable (or S-Video Cable) between the AV IN 2 [VIDEO] (or S-VIDEO) jack on the TV and the VIDEO OUT jack on the Camcorder. Connect Audio Cables between the AV IN 2 [L-AUDIO-R] jacks on the TV and the AUDIO OUT jacks on the Camcorder. TV Side Panel 1 S-Video Cable(Not supplied) or Camcorder 1 Video Cable (Not supplied) 2 Audio Cable (Not supplied) ➢ ➢ Each Camcorder has a different back panel configuration. When connecting a Camcorder, match the color of the connection terminal to the cable. Connecting a DVD Player/Set-Top Box The rear panel jacks on your TV make it easy to connect a DVD Player/Set-Top Box to your TV. 1 Connect Component Cables between the COMPONENT IN 1 [Y, PB, PR] (or COMPONENT IN 2 [Y, PB, PR]) jacks on the TV and the COMPONENT OUT [Y, PB, PR] jacks on the DVD Player/ Set-Top Box. 2 Connect Audio Cables between the COMPONENT IN 1 [R-AUDIO-L](or COMPONENT IN 2 [R-AUDIO-L]) jacks on the TV and the AUDIO OUT jacks on the DVD Player/Set-Top Box. TV Rear Panel DVD Player / Set-Top Box 2 Audio Cable (Not supplied) 1 Component Cable (Not supplied) ➢ ➢ ➢ Component video separates the video into Y (Luminance (brightness)), PB (Blue) and PR (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also. Each DVD Player/Set-Top box has a different back panel configuration. When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable. English - 12 BN68-01192F-02Eng-1.indd 12 2007-02-26 ソタネト 3:17:08 Connecting a DVD Player/Set-Top Box via HDMI This connection can only be made if there is an HDMI Output jack on the external device. This connection will provide the highest quality picture. 1 Connect an HDMI Cable between the HDMI IN 2 on the TV and the HDMI OUT on the DVD Player/Set-Top Box. TV Rear Panel DVD Player / Set-Top Box 1 HDMI Cable (Not supplied) What is HDMI? • HDMI, or high-definition multimedia interface, is an interface that enables the transmission of digital audio and video signals using a single cable without compression. • The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed. ➢ Each DVD Player/Set-Top box has a different back panel configuration. ➢ When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable. ➢ When connecting via HDMI, you do not need to connect Audio Cables. You only need to connect Audio cables when connecting via HDMI/DVI. Connecting a DVD Player/Set-Top Box via DVI This connection can only be made if there is a DVI Output jack on the external device. 1 Connect a HDMI/DVI Cable or DVI-HDMI Adapter between the [HDMI IN 1] jack on the TV and the DVI jack on the DVD Player/Set-Top Box. 2 Connect Audio Cables between the DVI IN (HDMI 1) [R-AUDIO-L] jack on the TV and the AUDIO OUT jacks on the DVD Player/Set-Top Box. DVD Player / Set-Top Box TV Rear Panel 2 Audio Cable (Not supplied) 1 HDMI/DVI Cable (Not supplied) ➢ ➢ ➢ Each DVD Player/Set-Top box has a different back panel configuration. When connecting a DVD Player/Set-Top box, match the color of the connection terminal to the cable. Only HDMI IN 1 can support HDMI and DVI. English - 13 BN68-01192F-02Eng-1.indd 13 2007-02-26 ソタネト 3:17:13 Connecting a Digital Audio System The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV. 1 Connect an Optical Cable between the DIGITAL AUDIO OUT (OPTICAL) jacks on the TV and the Digital Audio Input (OPTICAL) jacks on the Digital Audio System. When a Digital Audio System is connected to the “DIGITAL AUDIO OUT (OPTICAL)” terminal: Decrease the gain (volume) of the TV, and adjust the volume level with the system’s volume control. Digital Audio System TV Rear Panel Optical Cable (Not supplied) What is OPTICAL? • Converts the electric signal into an optical light signal, and transmits it through glass fibers. S/PDIF is a transmission system of digital audio in the form of a light wave that uses a glass conductor. ➢ 5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH. ➢ Each external input source device has a different back panel configuration. ➢ If you have an external device (DVD. Cable/Set-top box) connected via HDMI to the TV, audio is not output from the Optical jack. Connecting an Amplifier/DVD Home Theater 1 Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] on the TV and AUDIO IN [L-AUDIO-R] on the Amplifier/DVD Home Theater. When an audio amplifier is connected to the “AUDIO OUT [R-AUDIO-L]” terminals: Decrease the gain (volume) of the TV, and adjust the volume level with the Amplifier’s volume control. TV Rear Panel Amplifier/DVD Home Theater Audio Cable (Not supplied) ➢ ➢ Each Amplifier/DVD Home Theater has a different back panel configuration. When connecting an Amplifier/DVD Home Theater, match the color of the connection terminal to the cable. Connecting a PC 1 2 Connect a D-Sub Cable between PC IN [PC] jack on the TV and the PC output jack on your computer. TV Rear Panel PC Connect a PC Audio Cable between PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your computer. 2 PC Audio Cable (Not supplied) 1 D-Sub Cable (Not supplied) ➢ ➢ ➢ Each PC has a different back panel configuration. When connecting a PC, match the color of the connection terminal to the cable. When using an HDMI/DVI cable connection, you must use the HDMI IN1 terminal. English - 14 BN68-01192F-02Eng-1.indd 14 2007-02-26 ソタネト 3:17:19 Operation Turning the TV On and Off Press the POWER button on the remote control. You can also use the POWER button on the TV. ➢ It may take a while when your TV starts. Plug & Play Feature When the TV is initially powered On, basic settings proceed automatically and subsequently: 1 Press the POWER button on the remote control. The message Menu language, Shop Mode, Channels and Time will be set. is displayed. i Menu language, Shop Mode, Channels and Time will be set. Start Plug & Play 2 Press the ENTER button to enter the language. Press the ▲ or ▼ button to select language, then press the ENTER button. The message Select Home Mode when installing this TV at home. is automatically displayed. Select the language of the OSD. Menu Language Move :English Spanish French Enter Skip Plug & Play 3 Press the ◄ or ► button to select Shop or Home, then press the ENTER button. ➢ The default selection is Home. ➢ We recommend setting the TV to Home mode for the best picture in your home environment. ➢ Shop mode is only intended for use in retail environments. ➢ If the unit is accidentally set to Shop mode and you want to return to Dynamic (Home) mode, press the Volume button and then hold down the MENU button for five seconds on the TV panel. Select Home Mode when installing this TV at home. Home Shop RETURN Move Enter Skip FAV.CH Plug & Play 4 Press the ▲ or ▼ button to memorize the channels of the selected connection. Press the ENTER button to select Start. ➢ If the antenna is connected to ANT1 IN(AIR), select Air and if it is connected to ANT 2 IN(CABLE), select Cable. ➢ If both ANT 1 IN(AIR) and ANT 2 IN(CABLE) are connected, select the Air + Cable. ➢ In Cable mode, select the correct analog signal cable system source from among STD, HRC, and IRC by pressing the ▲ or ▼ button, then press the ENTER button. If you have Digital cable TV, select the cable system signal source for both Analog and Digital. Contact your local cable company to identify the type of cable system that exists in your particular area. To memorize the channels, press the ► button to select Start, then press the ENTER button. Contact your local cable company to identify the type of cable system that exists in your particular area. Select the antennas to memorize. Start Start Start Air Cable Air + Cable Move Enter Plug & Play Select the cable system. Analog STD HRC IRC Skip Start Digital STD HRC IRC Move Enter Skip Continued... English - 15 BN68-01192F-02Eng-1.indd 15 2007-02-26 ソタネト 3:17:29 5 The TV will begin memorizing all of the available channels. After all the available channels are stored, the Auto program menu reappears. Press the ENTER button when channel memorization is complete. Clock Mode menu is automatically displayed. ➢ To stop the search before it has finished, press the ENTER button with Stop selected. Plug & Play Auto Program in progress. Cable Channel 67 68% Stop Skip Enter Plug & Play Auto Program is completed. 14 Channels were memorized. Air : 9 , Cable : 5. OK Skip Enter 6 7 Press the ENTER button. Press the ▲ or ▼ button to select Manual if you want to set the current time manually, then press the ENTER button. Set current date and time. is displayed. ➢ If you select Auto, Set to daylight savings time. is displayed, then go to step 9. Press the ◄ or ► button to move to Month, Day, Year, Hour, Minute, or am/pm. Set the date and time you want by pressing the ▲ or ▼ button, then press the MENU button. ➢ You can set the Month, Day, Year, Hour, and Minute directly by pressing the number buttons on the remote control. Plug & Play Select the clock mode. Clock Mode The message Enjoy your watching. is displayed. When you have finished, press the ENTER button. ➢ Even if the ENTER button is not pressed, the message will automatically disappear after several seconds. Enter Move Skip Plug & Play Set the current time. Move 8 :Manual Auto i Day Month -- -- Year ---- Hour Minute am/pm -- -- -Enter Adjust Skip Enjoy your watching. OK Setting the Clock Automatically 9 Press the ENTER button. Press the ▲ or ▼ button to select On or Off, then press the ENTER button. Select the time zone in which you live. menu is automatically displayed. Plug & Play Set to daylight savings time. Move 10 Press the ▲ or ▼ button to highlight the time zone for your local area (and to move the highlight to the appropriate time zone on the map of the United States). Press the ENTER button. If clock is not automatically set, see page 48 to set the clock. Enter Skip Plug & Play Select the time zone in which you live. Newfoundland Atlantic Eastern Central Mountain Pacific Alaska Hawaii Move 11 The message Enjoy your watching. is displayed. When you have finished, press the ENTER button. ➢ Even if the ENTER button is not pressed, the message will automatically disappear after several seconds. On : Off Daylight Savings Time i Enter Skip Enjoy your watching. OK Continued... English - 16 BN68-01192F-02Eng-1.indd 16 2007-02-26 ソタネト 3:17:34 If you want to reset this feature... 1 2 TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ENTER button to select Plug & Play. For further details on setting up options, refer to the page 15~16. ➢ The Plug & Play feature is only available in the TV and DTV mode. i ► ► ► ► ► ► ► : English : Off : Medium Enter Return Menu language, Shop Mode, Channels and Time will be set. Start Changing Channels Using the Channel Buttons 1 Press the CH or CH button to change channels. When you press the CH or CH button, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels). You will not see channels that were either erased or not memorized. See page 19 to memorize channels. ➢ Using the Number Buttons 1 Press the number buttons to go directly to a channel. For example, to select channel 27, press 2, then 7. The TV will change channels when you press the second number. RETURN FAV.CH Using the “-” Button The “-” button is used to select stations that broadcast a digital signal. 1 For example, for Channel 7-1, press 7, then -, then 1. HD indicates the TV is receiving a Digital High Definition signal. SD indicates the TV is receiving a Standard Definition signal. ➢ For quick channel change, press the number buttons, then press the ENTER button. ➢ Using the PRE-CH Button to select the Previous Channel Use the number buttons to quickly tune to any channel. 1 Press the PRE-CH button. The TV will switch to the last channel viewed. ➢ To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then use the PRE-CH button to quickly alternate between them. RETURN FAV.CH RETURN FAV.CH English - 17 BN68-01192F-02Eng-1.indd 17 RETURN 2007-02-26 ソタネト 3:17:37 Adjusting the Volume Using the Volume Buttons 1 Press the VOL + or VOL – button to increase or decrease the volume. Using the Mute Button At any time, you can cut off the sound using the MUTE button. 1 Press MUTE and the sound cuts off. The word “Mute” will appear in the lower-left corner of the screen. 2 To turn mute off, press the MUTE button again, or simply press the VOL + or VOL – button. RETURN FAV.CH RETURN Viewing the Display The display identifies the current channel and the status of certain audio-video settings. 1 Press the INFO button on the remote control. The TV will display the channel, the type of sound, and the status of certain picture and sound settings. Press the INFO button once more or wait approximately 10 seconds and it disappears automatically. FAV.CH Air 28 Mono Picture Mode : Dynamic Sound Mode : Custom MTS : Stereo 12 : 00 am RETURN FAV.CH Viewing the Menus 1 With the power on, press the MENU button. The main menu appears on the screen. Its left side has five icons: Picture, Sound, Channel, Setup, Input. 2 Use the ▲ or ▼ button to select one of the five icons. Then press the ENTER button to access the icon’s sub-menu. 3 Press the EXIT button to exit. ➢ It takes about one minute until the on-screen menu disappears. TV Picture Mode Contrast Brightness Sharpness Color Tint G 50 ▼ : Dynamic ► 100 45 75 55 R 50 More Move Enter Exit RETURN English - 18 FAV.CH BN68-01192F-02Eng-1.indd 18 2007-02-26 ソタネト 3:17:42 Memorizing the Channels Your TV can memorize and store all of the available channels for both “off-air” (air) and cable channels. After the or CH button to scan through the channels. This eliminates available channels are memorized, use the CH the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual). Selecting the Video Signal-source Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an air or a cable system). 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 Press the ENTER button select Antenna. Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button. TV Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter TV Channel Air Antenna : Air Cable Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter Press the EXIT button to exit. Storing Channels in Memory (Automatic Method) 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 Press the ▲ or ▼ button to select Auto Program, then press the ENTER button. 3 4 5 Press the ▲ or ▼ button to select the antenna connection, then press the ENTER button. ➢ Air: “Air” antenna signal. Cable: “Cable” antenna signal. Air+Cable: “Air” and “Cable” antenna signals. ➢ If the antenna is connected to ANT 2 IN (CABLE), select Cable and if it is connected to ANT 1 IN (AIR), select Air. ➢ If both ANT 1 IN and ANT 2 IN are connected, select the Air + Cable. ➢ If you selected Air, then go to step 5. Press the ▲ or ▼ to select the correct analog signal cable system source from among STD, HRC, and IRC, then press the ENTER button. If you have Digital cable TV, select the cable system signal source for both Analog and Digital. ➢ If you have Digital cable TV, select the signal source for both Analog and Digital. ➢ STD, HRC, and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. The TV begins memorizing all available stations. If you want to stop Auto Programming, press the ENTER button. The Stop Auto Program? message will be displayed. Select Yes by pressing the ◄ or ► button. Press the EXIT button to exit. ➢ The TV must be connected to antenna/cable in order to receive digital TV signals. Even if a particular channel is deleted from the memory, you can always tune to that channel directly by using the number buttons on the remote control. ➢ • All available DTV and analog channels are automatically stored in memory. • It takes approximately 3 to 10 minutes to memorize channels. ► ► ► ► ► ► ► ► Return TV Return Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter TV ► ► ► ► ► ► ► ► Return Auto Program Select the antennas to memorize. Air Start Start Start Cable Air + Cable Move TV Return Enter Auto Program Select the cable system. Analog STD Start HRC IRC Digital STD HRC IRC Move Enter Return Auto Program Auto Program in progress. Cable Channel 67 68 % Stop Return Enter Auto Program Stop Auto Program? 68 % Yes Move No Enter Return English - 19 BN68-01192F-02Eng-1.indd 19 2007-02-26 ソタネト 3:17:50 Setting Up Your Remote Control After your remote control has been properly set up, your remote control can operate in five different modes: TV, VCR, Cable, DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose. ➢ The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes. Setting Up the Remote to Operate Your VCR 1 Turn off your VCR. 2 Press the VCR button on your TV’s remote control. 3 Press the SET button on your TV’s remote control. 4 Using the number buttons on your remote control, enter three digits of the VCR code listed on page 22 of this manual for your brand of VCR. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.) 5 Press the POWER button on the remote control. Your VCR should turn on if your remote is set up correctly. If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 080. RETURN FAV.CH Note on Using Remote Control Modes: VCR When your remote control is in VCR mode, the volume buttons still control your TV’s volume. Setting Up the Remote to Operate Your Cable Box 1 Turn off your cable box. 2 Press the CABLE button on your TV’s remote control. 3 Press the SET button on your TV’s remote control. 4 Using the number buttons on your remote control, enter three digits of the cable box code listed on page 23 of this manual for your brand of cable box. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.) 5 Press the POWER button on the remote control. Your cable box should turn on if your remote is set up correctly. RETURN FAV.CH If your cable box does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of cable box. If no other codes are listed, try each code, 000 through 046. RETURN FAV.CH Note on Using Remote Control Modes: Cable Box When your remote control is in CABLE mode, the volume buttons still control your TV’s volume. Continued... RETURN FAV.CH English - 20 BN68-01192F-02Eng-1.indd 20 2007-02-26 ソタネト 3:17:52 Setting Up the Remote to Operate Your DVD 1 Turn off your DVD. 2 Press the DVD button on your TV’s remote control. 3 Press the SET button on your TV’s remote control. 4 Using the number buttons on your remote control, enter three digits of the DVD code listed on page 24 of this manual for your brand of DVD. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.) 5 Press the POWER button on the remote control. Your DVD should turn on if your remote is set up correctly. If your DVD does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of DVD. If no other codes are listed, try each code, 000 through 141. RETURN FAV.CH Note on Using Remote Control Modes: DVD When your remote control is in DVD mode, the volume buttons still control your TV’s volume. Setting Up the Remote to Operate Your Set Top Box 1 Turn off your STB. 2 Press the STB button on your TV’s remote control. 3 Press the SET button on your TV’s remote control. 4 Using the number buttons on your remote control, enter three digits of the STB code listed on page 23 of this manual for your brand of STB. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.) 5 Press the POWER button on the remote control. Your STB should turn on if your remote is set up correctly. RETURN FAV.CH If your STB does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other codes listed for your brand of STB. If no other codes are listed, try each code, 000 through 074. RETURN FAV.CH Note on Using Remote Control Modes: STB When your remote control is in STB mode, the volume buttons still control your TV’s volume. RETURN FAV.CH English - 21 BN68-01192F-02Eng-1.indd 21 2007-02-26 ソタネト 3:17:57 Remote Control Codes VCR Brand SAMSUNG ADMIRAL AIWA AKAI AUDIO DYNAMICS BELL&HOWELL BROKSONIC CANDLE CANON CITIZEN COLORTYME CRAIG CURTIS MATHES DAEWOO DB DIMENSIA DYNATECH ELECTROHOME EMERSON FISHER FUNAI GENERAL ELECTRIC GO VIDEO LG(Goldstar) HARMAN KARDON HITACHI INSTANT REPLAY JC PENNEY JCL KENWOOD KLH LIOYD LOGIK LXI JVC MAGNAVOX MARANTZ MARTA KONIA ORION MEI MEMOREX MGA MIDLAND MINOLTA Code 000 001 002 003 004 005 077 078 079 020 025 004 027 032 007 026 018 022 002 003 006 008 015 055 021 056 002 003 006 008 015 055 007 002 024 002 007 008 017 021 025 056 064 066 003 010 011 012 013 014 015 016 007 026 017 025 034 001 003 006 021 022 025 030 032 034 040 047 050 052 060 063 065 066 067 069 073 018 024 028 029 048 051 061 025 002 005 017 021 056 002 006 007 008 009 010 007 019 025 041 042 074 021 002 007 018 019 021 026 037 041 054 056 007 008 018 021 026 037 007 008 018 026 037 070 025 038 025 081 082 083 021 056 059 007 008 018 021 026 037 062 006 036 073 074 075 076 021 006 021 024 025 034 005 019 041 075 Brand MITSUBISHI MONTGOMERY WARD MTC MULTITECH NEC OPTIMUS PANASONIC PENTAX PENTEX RESEARCH+ PHILCO PHILIPS PIONEER PORTLAND PROSCAN QUARTZ QUASAR RADIO SHACK/ REALISTIC RCA SANSUI SANYO SCOTT SEARS SHARP SHIMTOM SIGNATURE SONY SYLVANIA SYMPHONIC TANDY TASHIKA TATUNG TEAC TECHNICS TEKNIKA TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH Code 019 034 041 046 020 002 025 002 005 025 038 007 008 018 026 037 062 064 020 021 056 071 072 019 041 075 008 021 056 059 021 080 019 026 039 053 015 049 055 017 018 021 056 006 018 020 021 024 025 029 034 048 056 002 017 019 021 035 041 043 057 068 076 026 018 024 003 047 052 067 006 018 019 024 028 029 041 048 051 020 034 045 015 027 033 038 058 025 027 033 044 021 025 056 059 025 018 025 006 037 025 037 068 021 006 021 025 031 066 003 019 029 051 052 002 006 002 007 026 026 007 026 002 002 003 006 019 020 021 024 025 034 038 041 007 008 018 026 037 023 027 033 Continued... English - 22 BN68-01192F-02Eng-1.indd 22 2007-02-26 ソタネト 3:18:01 CABLE BOX Brand SAMSUNG GI HAMLIN HITACHI JERROLD MACOM MAGNAVOX OAK PANASONIC PHILIPS PIONEER RCA REGAL Code 000 001 002 003 004 005 006 007 041 003 024 031 025 030 038 039 025 030 019 023 028 026 003 022 027 037 044 019 021 023 028 004 018 020 044 014 022 040 003 Brand REGENCY SA SCIENTIFIC ATLAN SPRUCER STARGATE 2000 SYLVANIA TEXSCAN TOCOM UNIVERSAL VIEWSTAR WARNER AMEX ZENITH Code 015 023 042 043 042 043 022 036 016 016 032 033 034 019 021 023 028 046 017 029 035 037 045 SAMSUNG SET-TOP BOX Product Ground wave STB Satellite STB CABLE STB STB DVD COMBO Satellite STB HDD COMBO Standard Code 001 002 003 004 008 009 Product Satellite STB HDD COMBO Premium CABLE STB HDD COMBO Standard CABLE STB HDD COMBO Premium Ground wave STB HDD COMBO Standard Ground wave STB HDD COMBO Premium Code 010 011 012 013 014 SET-TOP BOX Brand ALPHASTAR ANAM CHANNEL MASTER CROSSDIGITAL CHAPARRAL DIRECT TV DAEWOO DISH NETWORK SYSTEM DISHPRO DRAKE DX ANTENNA ECHOSTAR EXPRESSVU GOI GE GENERAL INSTRUMENT HTS HOME CABLE HITACHI HUGHES NETWORK IQ IQ PRISM JANEIL JERROID JVC Code 023 043 018 034 019 035 015 016 017 019 022 045 060 061 062 065 066 067 068 074 069 070 069 018 024 032 027 025 069 070 071 069 069 065 046 047 048 063 064 069 056 022 015 017 020 020 059 063 069 070 Brand LG(Goldstar) MAGNAVOX MEMOREX MOTOROLA MACOM MITSUBISHI NEXT LEVEL PHILIPS PRIMESTAR PANASONIC PAYSAT PROSCAN RCA RADIOSHACK REALISTIC STS STAR TRAK SKY SKY LIFE SHACK STAR CHOICE SONY TOSHIBA ULTIMATE TV UNIDEN ZENITH Code 044 073 016 021 036 038 039 040 041 042 016 064 018 015 047 048 064 015 016 017 021 033 036 038 039 040 041 042 067 046 049 050 063 058 059 061 062 016 065 066 051 052 053 065 066 064 057 020 027 026 031 005 006 007 064 064 054 060 015 017 028 029 030 072 060 066 016 021 037 055 056 057 024 031 068 Continued... English - 23 BN68-01192F-02Eng-1.indd 23 2007-02-26 ソタネト 3:18:02 SAMSUNG DVD Product DVD DVDR BD Record VCR COMBO VCR Record DHR COMBO Code 000 001 002 003 004 005 006 007 008 009 010 011 012 013 Product Home Theater VCR COMBO HDD Record COMBO TWIN TRAY COMBO STB DVD COMBO DVD Receiver AV Receiver Code 014 015 016 017 018 019 020 021 DVD Brand ANAM AUDIOVOX AUDIOLOGIC ANABA APEX DIGITAL AIWA BROKSONIC BLAUPUNKT B&K CURTIS MATHES CYBER HOME CLARION CIRRUS CINEVISION DAEWOO DENON FARENHEIT FISHER GPX GO VIDEO GE GREENHILL HITACHI HITEKER HOYO HARMAN / KARDON IRT INTEGRA JBL JVC JATON KENWOOD KISS KONKA KLH LG(Goldstar) LOEWE LASONIC MOBILE AUTHORITY MEMOREX MALATA MAGNAVOX MINTEK MONYKA Code 030 075 085 072 070 071 074 086 083 084 088 111 112 114 062 074 122 123 027 065 077 078 079 082 080 125 081 095 066 146 067 068 090 060 061 089 133 135 069 074 074 064 113 071 073 091 110 089 092 091 022 033 115 116 073 051 108 109 073 059 100 106 107 074 075 025 031 057 058 054 055 056 076 093 074 094 073 Brand NORCENT NEXT BASE NEC NANTAUS NESA OPTOMEDIA ELECTRONICS OPTIVIEW ONKYO PHILCO PRINCETON PROSCAN PANASONIC PHILIPS ROTEL RIO RCA RAITE ROWA SAMPO SONY SHERWOOD SVA SYLVANIA SHARP SANSUI SANYO SHINSONIC SANYO THOMSON TOSHIBA TECHNICS TVIEW TOKAI TEAC TECHWOOD TREDEX URBAN CONCEPTS VENTURER VOCOPRO YAMAHA YAMAKAWA XWAVE ZENITH Code 048 049 050 052 053 144 074 105 072 076 092 119 044 045 046 047 023 024 034 124 134 136 137 138 036 076 117 118 120 023 035 074 075 131 132 073 038 104 026 029 126 127 128 129 130 141 039 041 042 043 093 140 062 062 094 090 145 028 062 076 139 072 073 096 097 098 099 101 076 075 102 032 063 040 073 103 076 121 English - 24 BN68-01192F-02Eng-1.indd 24 2007-02-26 ソタネト 3:18:02 To Select the Source Use to select TV or other external input sources such as DVD players or Set-top/Cable boxes connected to the TV. Use to select the input source of your choice. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input, then press the ENTER button. 2 Press the ENTER button to select Source List. Press the ▲ or ▼ button to select signal source, then press the ENTER button. ➢ You can choose between the following sets of jacks: AV1, S-Video1, Component1, Component2, PC, HDMI1, or HDMI2 on the TV’s rear panel and AV2, S-Video2, or HDMI3 on the TV’s side panel. ➢ HDMI1, HDMI2, or HDMI3 input can only be selected when the external device is turned on and connected via HDMI. ➢ You can choose only those external devices that are connected to the TV. Input TV Source List : TV Edit Name Anynet+ (HDMI-CEC) Move TV ► ► Enter Return Source List TV AV1 AV2 S-Video1 S-Video2 Component1 Component2 ▼ More Move :---:---:---:---:---:---Enter Return You can also press the SOURCE button on the remote control to view an external signal source. To Edit the Input Source Name You can name the device connected to the input jacks to make your input source selection easier. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input, then press the ENTER button. Press the ▲ or ▼ button to select Edit Name, then press the ENTER button. TV Input Source List : TV Edit Name Anynet+ (HDMI-CEC) Move 2 Press the ▲ or ▼ button to select AV1, AV2, S-Video1, S-Video2, Component1, Component2, PC, HDMI1, HDMI2, or HDMI3 input jack, then press the ENTER button. TV Press the ▲ or ▼ button to select VCR, DVD, D-VHS, Cable STB, HD STB, Satellite STB, PVR STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, PC, VOD STB, or TV input source, then press the ENTER button. AV1 AV2 S-Video1 S-Video2 Component1 Component2 ▼ More TV Return :---:---:---:---:---:---- ► ► ► ► ► ► Return Enter Edit Name AV1 AV2 S-Video1 S-Video2 Component1 Component2 ▼ FAV.CH More RETURN Press the EXIT button to exit. Enter Edit Name Move 3 ► ► Move TV ---: -VCR ----: -DVD --: -D-VHS - - -STB : -Cable - STB -: -HD - - - STB : -Satellite PVR STB ▼ Enter Return Edit Name ▲ AV1 AV2 S-Video1 S-Video2 Component1 Component2 ▼ More Move AV Receiver :DVD - - Receiver ----:Game ---:Camcorder - - Combo -:DVD ---:PC - - -STB :VOD TV Enter Return English - 25 BN68-01192F-02Eng-1.indd 25 2007-02-26 ソタネト 3:18:04 Picture Control Using Automatic Picture Settings Your TV has three automatic picture settings (“Dynamic”, “Standard”, and “Movie”) that are preset at the factory. You can activate either Dynamic, Standard, or Movie by making a selection from the menu. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Picture, then press the ENTER button. TV Picture Mode Contrast Brightness Sharpness Color Tint G 50 ▼ : Dynamic More Move 2 Press the ENTER button to select Mode. Press the ▲ or ▼ button to select the Dynamic, Standard, or Movie picture setting, then press the ENTER button. ► 100 45 75 55 R 50 TV Enter Return Picture Mode Contrast Brightness Sharpness Color Tint G 50 • Choose Dynamic to increase the clarity and sharpness of the picture. • Choose Standard for general TV watching mode. • Choose Movie when watching movies. ▼ : Dynamic Dynamic Standard Movie 100 45 75 55 R 50 More RETURN Move Enter Return Press the P.MODE button on the remote control to select one of the standard picture settings. FAV.CH 3 Press the ▲ or ▼ button to select Contrast, Brightness, Sharpness, Color, or Tint, then press the ENTER button. TV Mode Mode Contrast Brightness Sharpness Color Tint G 50 ▼ : Dynamic More Move 4 Press the ◄ or ► button to decrease or increase the value of a particular item. Press the ENTER button. ➢ • Tint doesn’t operate in PC mode. • In PC mode, only the Contrast and Brightness can be selected. • Each adjusted setting will be stored separately according to its input mode. • When you make changes to Contrast, Brightness, Sharpness, Color, or Tint. OSD color will also be adjusted accordingly. 100 45 75 55 R 50 Enter Return Contrast 100 Move Adjust Return Continued... English - 26 BN68-01192F-02Eng-1.indd 26 2007-02-26 ソタネト 3:18:07 TV 5 Press the ENTER button to return to Picture. 6 Press the ▲ or ▼ button to select Color Tone, then press the ENTER button. 7 Press the ▲ or ▼ button to select Cool2, Cool1, Normal, Warm1, or Warm2, then press the ENTER button. ➢ When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected. Resetting the Picture Settings to the Factory Defaults 8 Picture More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move ▲ TV : Cool1 : 16:9 : Auto : On : On : OK Enter ► ► ► ► ► ► ► Return Picture More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move ▲ TV : Cool1 Cool2 Cool1 Normal : 16:9 Warm1 : Auto Warm2 : On : On : OK Enter Return Picture More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move ▲ Press the ▲ or ▼ button to select Reset, then press the ENTER button. Press the ▲ or ▼ button to select OK, then press the ENTER button. Press the EXIT button to exit. ➢ Each picture mode can be reset. : Cool1 : 16:9 : Auto : On Cancle : On : OK Enter Return Digital Noise Reduction If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen. 1 2 3 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Picture, then press the ENTER button. TV Press the ▲ or ▼ button to select Digital NR, then press the ENTER button. Press the ▲ or ▼ button to select Off, Low, Mediunm, High, or Auto, then press the ENTER button. Press the EXIT button to exit. ➢ The Digital NR function is available in all modes except PC. Picture More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move ▲ TV ► ► ► ► ► ► ► : Cool1 : 16:9 : Auto : On : On : OK Enter Return Picture ▲ More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move : Cool1 Off : 16:9 Low Medium : Auto High : On Auto : On : OK Enter Return English - 27 BN68-01192F-02Eng-1.indd 27 2007-02-26 ソタネト 3:18:09 Changing the Screen Size Screen size selection depends on the type of video input. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Picture, then press the ENTER button. 2 Press the ▲ or ▼ button to select Size, then press the ENTER button. 3 Press the ▲ or ▼ button to select the screen format you want. Press the ENTER button. TV Press the EXIT button to exit. • 16:9 : Sets the picture to 16:9 wide mode. • Zoom1 : Magnifies the size of the picture on the screen. • Zoom2 : Expands the Zoom1 format picture. • Wide Fit : Enlarges the aspect ratio of the picture to fit the entire screen. • 4:3 : Sets the picture to 4:3 normal mode. • Just Scan : Use this function to see the full image without any cutoff when DTV or HDMI 720p/1080i signals are input. Press the P.SIZE button on the remote control to change the picture size. Picture More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move ▲ TV : Cool1 : 16:9 : Auto : On : On : OK Enter ► ► ► ► ► ► ► Return Size 16:9 Zoom1 Zoom2 Wide Fit 4:3 Just Scan Move ▲ Position ▼ Reset Enter Return RETURN FAV.CH ➢ 16:9 Sets the picture to 16:9 wide mode. Zoom1 The screen size when Wide screen is vertically enlarged. Zoom2 The screen size when the Zoom1 screen is vertically enlarged. Wide Fit Enlarges the aspect ratio of the picture to fit the entire screen. 4:3 Sets the picture to 4:3 normal mode. Just Scan Use this function to see the full image without any cutoff when DTV or HDMI 720p/1080i signals are input. • In TV, VIDEO, S-VIDEO, and COMPONENT(480i, 480p) modes, all screen modes can be selected. (16:9 ➞ Zoom1 ➞ Zoom2 ➞ 4:3) • In COMPONENT(720p, 1080i) or HDMI(720p, 1080i) mode, 16:9, 4:3 and Wide Fit can be selected. • In Zoom1, Zoom2 and Wide Fit modes, you can move the picture on the screen by pressing the ▲ or ▼ button. • You can not change the picture size when PIP is set to Double. • When Double ( , ) mode has been set in PIP, the Picture Size cannot be set. • Wide Fit can be used when watching a Digital HD (High Definition) signal. Wide Fit sets the optimum picture format by expanding it both horizontally and vertically. For example, you can reset the picture in 4:3 format to 16:9. Wide Fit does not support all external devices (DVD, VCR etc.). English - 28 BN68-01192F-02Eng-1.indd 28 2007-02-26 ソタネト 3:18:12 Making Detailed Picture Settings You can set detailed picture settings. TV 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Picture, then press the ENTER button. 2 Press the ▲ or ▼ button to select Detailed Settings, then press the ENTER button. 3 Select the desired Detailed Settings option by pressing the ▲ or ▼ button, then press the ENTER button. 4 TV When you are satisfied with your setting, press the ENTER button. When the picture mode is set to Dynamic, Detailed Settings cannot be selected. Move Dynamic Contrast: Off/Low/Medium/High You can adjust the screen contrast so that the optimal contrast is provided. White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset You can adjust the color temperature for more natural picture colors. R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the adjusted screen. Select the desired option by pressing the ▲ or ▼ button, then press the ENTER button. Press the ◄ or ► button until you reach the optimal setting. Reset: The previously adjusted white balance will be reset to the factory defaults. Move Move Enter Gamma Return Return 0 Adjust TV Return Detailed Settings Black Adjust : Off Dynamic Contrast : Off Gamma :0 Color Space : Wide Auto Wide White Balance My Color Control Edge Enhancement : Off Move Enter Return White Balance R-Offset G-Offset B-Offset R-Gain G-Gain B-Gain Reset 15 15 15 15 15 15 Move Enter Return My Color Control Pink Green Blue White Reset 15 15 15 15 Move TV 29 Enter Detailed Settings Black Adjust : Off Off Dynamic Contrast : Off Gamma : 0Low Medium Color Space : Wide High White Balance My Color Control Edge Enhancement : Off Edge Enhancement: Off/On You can emphasize object boundaries. BN68-01192F-02Eng-1.indd Return Detailed Settings TV My Color Control: Pink/Green/Blue/White/Reset This setting can be adjusted to suit your personal preferences. Pink/Green/Blue/White: Select the desired color by pressing the ▲ or ▼ button, then press the ENTER button. Press the ◄ or ► button until you reach the optimal setting. ➢ When using the My Color Control Feature, the current picture remains in movement. Reset: The previously adjusted colors will be reset to the factory defaults. English - 29 Enter ► ► ► ► ► ► ► Black Adjust : Off Off Low Dynamic Contrast : Off Gamma : 0Medium High Color Space : Wide White Balance My Color Control Edge Enhancement : Off Black Adjust: Off/Low/Medium/High You can directly select the black level on the screen to adjust the screen depth. Color Space: Auto/Wide Color space is a color matrix composed of red, green, and blue colors. Select your favorite color space and experience the most natural color. You can set the color reproduction space for the input signal to Auto or Wide. : 16:9 : Auto : On : On : OK Enter ► ► ► ► ► ► ► Return Detailed Settings TV Gamma: -3 ~ 3 You can adjust the middle brightness of pictures. Press the ◄ or ► button until you reach the optimal setting. : Cool1 Black Adjust : Off Dynamic Contrast : Off Gamma :0 Color Space : Wide White Balance My Color Control Edge Enhancement : Off Press the EXIT button to exit. ➢ Picture More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move ▲ Enter Return Detailed Settings Black Adjust : Off Dynamic Contrast : Off Gamma :0 Color Space : Wide White Balance My Color Control Edge Enhancement : Off Off On Move Enter Return 2007-02-26 ソタネト 3:18:23 Active Color If you turn on this option, the colors of the sky and grass will be stronger and clearer for a more vivid on-screen picture. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Picture, then press the ENTER button. 2 Press the ▲ or ▼ button to select Active Color, then press the ENTER button. 3 Press the ▲ or ▼ button to select Off or On, then press the ENTER button. TV TV This function is not available in PC mode. When you select Standard or Movie in Picture Mode, the Active Color automatically changes to Off and it is deactivated. When the Picture Mode is set to Dynamic, the Active Color is activated regardless of the Picture Mode settings. ► ► ► ► ► ► ► : Cool1 : 16:9 : Auto : On : On : OK Enter Return Picture ▲ More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move Press the EXIT button to exit. ➢ ➢ Picture More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move ▲ : Cool1 : 16:9 : Auto : On Off : On On : OK Enter Return DNIe (Digital Natural Image engine) This TV includes the DNIe function to provide high visual quality. If you set DNIe to on, you can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you can view the difference in the visual quality. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Picture, then press the ENTER button. 2 Press the ▲ or ▼ button to select DNIe, then press the ENTER button. ➢ This function doesn’t work when the Input Source is PC. 3 Press the ▲ or ▼ button to select Off, DNIe or On, then press the ENTER button. Press the EXIT button to exit. Picture More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move ▲ TV • Off: Switches off the DNIe mode. • DNIe: The screen before applying DNIe appears on the left and the screen after applying DNIe appears on the right. • On: Switches on the DNIe mode. ➢ TV The DNIe function is not supported in the Standard and Movie mode. (It is inactivated.) ► ► ► ► ► ► ► : Cool1 : 16:9 : Auto : On : On : OK Enter Return Picture ▲ More Color Tone Detailed Settings Size Digital NR Active Color DNIe Reset Move : Cool1 : 16:9 : Auto Off : On DNIe : On : On Enter Return English - 30 BN68-01192F-02Eng-1.indd 30 2007-02-26 ソタネト 3:18:25 Selecting the Film Mode Automatically senses and processes film signals from all sources and adjusts the picture for optimum quality. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select Film Mode, then press the ENTER button. 3 Press the ▲ or ▼ button to select Off or On, then press the ENTER button. TV Setup More Screen Burn Protection ► HDMI Black Level : Normal ► Film Mode : Off ► Wall-Mount Adjustment ► PIP ► Function Help : On ► SW Upgrade ► Move Return Enter ▲ TV Setup More Screen Burn Protection HDMI Black Level : Normal : Off Film Mode Off Wall-Mount Adjustment On PIP Function Help : On SW Upgrade Move Return Enter ▲ Press the EXIT button to exit. Setting the Blue Screen Mode If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the “Blue Screen” mode to “Off”. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select Blue Screen, then press the ENTER button. 3 Press the ▲ or ▼ button to select Off or On, then press the ENTER button. TV Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ TV Enter Return Setup ▲ More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move Press the EXIT button to exit. ➢ Blue Screen is displayed when there is no signal from an external device, regardless of the Blue Screen Setting. ► ► ► : Off ► : In Watching TV ► : Off ► : Off : Medium : Off Off : Medium On : Off : In Watching TV : Off Enter Return Setting the HDMI Black Level Use this function to adjust the Black Level of the picture while in HDMI mode. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select HDMI Black Level, then press the ENTER button. 3 Press the ▲ or ▼ button to select Normal or Low, then press the ENTER button. Press the EXIT button to exit. ➢ This function is active only when the externel input connects to HDMI(RGB signals). TV Setup More Screen Burn Protection ► HDMI Black Level : Normal ► Film Mode : Off ► Wall-Mount Adjustment ► PIP ► Function Help : On ► SW Upgrade ► Move Return Enter ▲ TV Setup More Screen Burn Protection HDMI Black Level : Normal Normal Film Mode : Off Low Wall-Mount Adjustment PIP Function Help : On SW Upgrade Move Return Enter ▲ English - 31 BN68-01192F-02Eng-1.indd 31 2007-02-26 ソタネト 3:18:27 Viewing Picture-in-Picture This product has one built-in tuner, which does not allow PIP to function in the same mode. For example, you cannot watch one TV channel in the main screen, and a different one in the PIP screen. Please see ‘PIP Settings’ below for details. You can use the PIP feature to simultaneously watch two video sources. (See page 37 to select the PIP picture sound.) ➢ While V-Chip is in operation, the PIP function cannot be used. (Refer to page 56) Activating Picture-in-Picture TV 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select PIP, then press the ENTER button. 2 Press the ENTER button again. Press the ▲ or ▼ button to select On, then press the ENTER button. ➢ If you turn the TV off while watching in PIP mode and turn it on again, the PIP window will disappear. Setup More Screen Burn Protection ► HDMI Black Level : Normal ► Film Mode : Off ► Wall-Mount Adjustment ► PIP ► Function Help : On ► SW Upgrade ► Move Return Enter ▲ TV PIP PIP Size Position Channel RETURN Press the PIP button on the remote control to activate or deactivate the PIP. ➢ Move Off : Off : On : : DTV Air 3 - 0 Enter Return FAV.CH Analog TV signals can be viewed on the PIP screen while viewing the picture from an external source (DVD, Set-top box, PC etc.) connected to the Component 1, 2, PC and HDMI 1, 2, 3 jacks on the main screen. Changing the Size of the PIP Window 3 Press the ▲ or ▼ button to select Size, then press the ENTER button. Press the ▲ or ▼ button to select the desired size of the PIP window, then press the ENTER button. ➢ If main picture is in PC and HDMI 1 modes, Size is not available. ➢ You may notice that the picture in the PIP window becomes slightly unnatural when you use the main picture to view a game or karaoke. TV PIP PIP Size Position Channel Move : On : : : DTV Air 3 - 0 Enter Return Continued... English - 32 BN68-01192F-02Eng-1.indd 32 2007-02-26 ソタネト 3:18:29 TV Changing the Position of the PIP Window 4 Press the ▲ or ▼ button to select Position, then press the ENTER button. Press the ▲ or ▼ button to select the desired PIP window position, then press the ENTER button. ➢ In Double Window ( ) and Double Wide ( ) modes, Position cannot be selected. ➢ If the PIP window is set to Double Window ( ) or Double Wide ( ) mode, the screen size or alignment may slightly differ depending on the signal type. Move TV Changing the PIP Channel 5 PIP PIP Size Position Channel Press the ▲ or ▼ button to select Channel, then press the ENTER button. Press the ▲ or ▼ button at the bottom of the remote to select the desired channel in the PIP window, then press the ENTER button. ➢ The channel can be active when the sub picture is set to TV. and CH and buttons on the remote control to change the PIP Enter Return PIP PIP Size Position Channel : On : : : DTV Air 3▲- 0 DTV Air 3-0 ▲ RETURN Move Press the EXIT button to exit. Press the PIP CH channel. : On : : : DTV Air 3 - 0 Enter Return FAV.CH Freezing the Current Picture RETURN 1 Press the STILL button to freeze a moving picture. ➢ Normal sound will still be heard. Press again to cancel. ➢ To prevent screen burn-in, this function will automatically cancel after 5 minutes. FAV.CH English - 33 BN68-01192F-02Eng-1.indd 33 2007-02-26 ソタネト 3:18:31 Sound Control Using Automatic Sound Settings Your TV has automatic sound settings (“Standard”, “Music”, “Movie”, “Speech”, and “Custom”) that are preset at the factory. Or, you can select “Custom”, which automatically recalls your personalized sound settings. 1 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. TV Sound Mode Equalizer SRS TruSurround XT Multi-Track Options Auto Volume Internal Mute Sound Select Reset Move Press the ENTER button to select Mode. Press the ▲ or ▼ button to select Standard, Music, Movie, Speech, or Custom sound setting, then press the ENTER button. Press the EXIT button to exit. • Choose Standard for the standard factory settings. • Choose Music when watching music videos or concerts. • Choose Movie when watching movies. • Choose Speech when watching a show that is mostly dialog (i.e., news). • Choose Custom to recall your personalized settings (see Customizing the Sound). : Custom Standard Music Movie : Off Speech Custom : Off : Off : Main Enter Return RETURN FAV.CH Press the S.MODE button on the remote control to select one of the standard sound settings. Customizing the Sound The sound settings can be adjusted to suit your personal preference. (Alternatively, you can use one of the “automatic” settings.) 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. 2 Press the ▲ or ▼ button to select Equalizer, then press the ENTER button. 3 Press the ◄ or ► button to select a particular frequency to adjust. Press the ▲ or ▼ button to increase or decrease the level of the particular frequency, then press the ENTER button. Press the EXIT button to exit. ➢ • R/L Sound Balance Adjustment: To adjust the sound balance of the R/L speakers. • Frequency Adjustment (100Hz, 300Hz, 1KHz, 3KHz, 10KHz): To adjust the level of different frequencies. ➢ If you make any changes to the equalizer settings, the sound mode is automatically switched to the Custom mode. Resetting the Equalizer Settings to the Factory Defaults To operate the Reset function, the Game mode must be set to On. (Refer to page 49) 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. 2 Press the ▲ or ▼ button to select Reset, then press the ENTER button. ➢ The equalizer resets to the factory defaults. TV Sound Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off Internal Mute : Off Sound Select : Main Reset Move Enter TV Return Equalizer R L Balance + + 0 0 - - 100Hz 300Hz 1KHz 3KHz 10KHz Move TV ► ► ► ► ► ► ► Adjust Return Sound Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off Internal Mute : Off Sound Select : Main Reset Move Enter ► ► ► ► ► ► ► Return Press the EXIT button to exit. English - 34 BN68-01192F-02Eng-1.indd 34 2007-02-26 ソタネト 3:18:35 Setting the TruSurround XT TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multi channel formats. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. Sound TV Press the EXIT button to exit. Mode Equalizer SRS TruSurround XT Multi-Track Options Auto Volume Internal Mute RETURN Sound Select Reset Move Press the SRS button on the remote control to select On or Off. FAV.CH 2 Press the ▲ or ▼ button to select SRS TruSurround XT, then press the ENTER button. 3 Press the ▲ or ▼ button to select Off or On, then press the ENTER button. : Custom : Off Off On : Off : Off : Main Enter Return TRADEMARK & LABEL LICENSE NOTICE TruSurround XT, SRS and Symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. Choosing a Multi-Channel Sound (MTS) Track - Digital The digital-TV broadcast system is capable of simultaneous transmission of many audio tracks (for example, simultaneous translations of the program into foreign languages). The availability of these additional “multitracks” depends upon the program. Preferred language TV 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. 2 Press the ▲ or ▼ button to select Multi-Track Options, then press the ENTER button. 3 Press the ENTER button to select Preferred Language. Press the ▲ or ▼ button to choose the language (English, Spanish, or French) you want, then press the ENTER button. Sound Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off Internal Mute : Off Sound Select : Main Reset Move Enter TV ► ► ► ► ► ► ► Return Multi-Track Options English Preferred Language : English Spanish Multi-Track Sound : Stereo French Press the EXIT button to exit. ➢ You can only select the language from among the actual languages being broadcast. RETURN Press the MTS button on the remote control to listen in a language other than the preferred language. FAV.CH Move Enter Return English - 35 BN68-01192F-02Eng-1.indd 35 2007-02-26 ソタネト 3:18:39 Choosing a Multi-Channel Sound (MTS) Track - Analog Depending on the particular program being broadcast, you can listen to Mono, Stereo or SAP. Multi-Track Sound TV 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. 2 Press the ▲ or ▼ button to select Multi-Track Options, then press the ENTER button. 3 Press the ▲ or ▼ button to select Multi-Track Sound, then press the ENTER button. Press the ▲ or ▼ button to select a setting you want, then press the ENTER button. Sound Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off Internal Mute : Off Sound Select : Main Reset Move Enter TV ► ► ► ► ► ► ► Return Multi-Track Options Preferred Language : English Mono Multi-Track Sound : Stereo Stereo SAP Press the EXIT button to exit. • Choose Mono for channels that are broadcasting in mono, or if you are having difficulty receiving a stereo signal. • Choose Stereo for channels that are broadcasting in stereo. • Choose SAP to listen to the Separate Audio Program, which is usually a foreignlanguage translation. RETURN Move Enter Return FAV.CH Press the MTS buttons on the remote control to select Mono, Stereo, or SAP. Automatic Volume Control Reduces the difference in volume level among broadcasters. TV 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. 2 Press the ▲ or ▼ button to select Auto Volume, then press the ENTER button. 3 Press the ▲ or ▼ button to select Off or On, then press the ENTER button. Sound Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off Internal Mute : Off Sound Select : Main Reset Move Enter TV Return Sound Mode Equalizer SRS TruSurround XT Multi-Track Options Auto Volume Internal Mute Sound Select Reset Move Press the EXIT button to exit. ► ► ► ► ► ► ► : Custom : Off : Off Off : Off On : Main Enter Return Selecting the Internal Mute Sound output from the TV speakers is muted. This is useful when you want to listen to audio through your sound system instead of the TV. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. 2 Press the ▲ or ▼ button to select Internal Mute, then press the ENTER button. TV Sound Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off Internal Mute : Off Sound Select : Main Reset Move Enter ► ► ► ► ► ► ► Return Continued... English - 36 BN68-01192F-02Eng-1.indd 36 2007-02-26 ソタネト 3:18:43 3 Press the ▲ or ▼ button to select Off or On, then press the ENTER button. TV Press the EXIT button to exit. ➢ • When Internal Mute is set to On, Sound menus except Multi-track Options cannot be adjusted. • The left/right audio outputs and digital audio outputs (Optical) remain enabled. • The VOL +, VOL - and MUTE buttons do not operate when the Internal Mute is set to On. TV’s Internal Speakers Sound Mode Equalizer SRS TruSurround XT Multi-Track Options Auto Volume Internal Mute Sound Select Reset Move : Custom : Off Off : Off On : Off : Main Enter Return Audio Out Optical (R/L Out) to Sound System TV AV, S-Video Component, PC, HDMI TV AV, S-Video Component, PC, HDMI Internal Mute Off Speaker Output Speaker Output Internal Mute On Mute Mute Speaker Output Sound Output Sound Output Sound Output Mute Sound Output Sound Output Video No Signal Mute Mute Sound Output Mute Mute Mute Mute When Internal Mute is set to On, Sound menus except Multi-Track Options cannot be adjusted. Adjusting the Melody Sound The TV power on/off melody sound volume can be adjusted. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select Melody, then press the ENTER button. 3 Press the ▲ or ▼ button to select Off, Low, Medium, or High, then press the ENTER button. TV Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ TV ► ► ► : Off ► : In Watching TV ► : Off ► : Off : Medium Enter Return Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ Press the EXIT button to exit. TRADEMARK & LABEL LICENSE NOTICE Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. : Off Off Low : Medium Medium High : Off : In Watching TV : Off Enter Return Listening to the Sound of the Sub (PIP) Picture When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Sound, then press the ENTER button. 2 Press the ▲ or ▼ button to select Sound Select, then press the ENTER button. 3 TV Press the ▲ or ▼ button to select Sub, then press the ENTER button. Press the EXIT button to exit. • Main: Used to listen to the sound of the main picture. • Sub: Used to listen to the sound of the sub picture. ➢ Sound Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off Internal Mute : Off Sound Select : Main Reset Move Enter TV Return Sound Mode Equalizer SRS TruSurround XT Multi-Track Options Auto Volume Internal Mute Sound Select Reset Move You can select this option when PIP is set to On. ► ► ► ► ► ► ► : Custom : Off : Off Main : Off Sub : Main Enter Return English - 37 BN68-01192F-02Eng-1.indd 37 2007-02-26 ソタネト 3:18:46 Channel Control Selecting the Antenna 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 TV Channel Air Antenna : Air Cable Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter Press the ENTER button to select Antenna. Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button. Press the EXIT button to exit. Press the ANTENNA button on the remote control to select Air or Cable. ➢ If the antenna is connected to ANT1 IN(AIR), select Air and if it is connected to ANT2 IN(CABLE), select Cable. ➢ If both ANT1 IN(AIR) and ANT2 IN(CABLE) are connected, select the antenna input you want. If the antenna input is not selected properly, noise may appear on the screen. Return Adding and Erasing Channels You can add or delete a channel to display the channels you want. To use the Channel List function, first run Auto Program (see page 19). RETURN 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 Press the ▲ or ▼ button to select Channel List, then press the ENTER button. 3 Press the ▲ or ▼ button to select Added, then press the ENTER button. TV Channel Antenna : Air Auto Program FAV.CH Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move TV Enter Move Press the ▲/▼/◄/► buttons to select a channel to add, then press the ENTER button. Press the ▲ or ▼ button to select Add, then press the ENTER button to add the channel. Press the MENU button to return. ➢ All added channels will be shown on Added menu. Return Channel List All Added Favorite Default List Mode 4 ► ► ► ► ► ► ► ► ► ► ► ► : All Enter Return Channel List /Added DTV Air 2 DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Move Air 16 DTV Air 9-1 Air 10 Air 11 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 List Mode Add All Delete All Enter Page Return Channel List /Added DTV Air 2 DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Continued... Watch DTV Air 9-1 AddAir 10 Delete Air 11 Favorite DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 List Mode Move Air 18 Enter Add All Delete All Return English - 38 BN68-01192F-02Eng-1.indd 38 2007-02-26 ソタネト 3:18:50 5 Press the ▲/▼/◄/► buttons to select a channel to delete, then press the ENTER button. Press the ▲ or ▼ button to select Delete, then press the ENTER button to delete the channel. Press the EXIT button to exit. • Red (P.MODE) button: Press repeatedly to select All, Added, or Favorite. • Green (S.MODE) button: Press to add all channels deleted. • Yellow (STILL) button: Press to delete all channels memorized. Channel List /Added DTV Air 2 Watch DTV Air 9-1 AddAir 10 Delete Air 11 Favorite DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Air 16 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 List Mode Move Delete All Page Enter Return Setting Your Favorite Channels You can set channels you watch frequently as favorites. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 Press the ▲ or ▼ button to select Channel List, then press the ENTER button. 3 Press the ▲ or ▼ button to select All or Added, then press the ENTER button. TV Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter TV Channel List All Added Favorite Default List Mode Move 4 Press the ▲/▼/◄/► buttons to select a channel as a favorite channel, then press the ENTER button. Press the CH and CH button to display the next channel list page. Press the ▲ or ▼ button to select Favorite, then press the ENTER button. The “ ” symbol will be highlighted and the channel will be set as a Favorite. To cancel your Favorite channel selection, press the ENTER button until the “ ” symbol disappears. Press the EXIT button to exit. ➢ Only memorized channels can be set as favorite channels. ➢ All favorite channels will be shown on the Favorite menu. To select the favorite channels you have set up, press the FAV.CH button on the remote control. ► ► ► ► : All Enter Return Channel List /Added DTV Air 2 DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Air 16 DTV Air 9-1 Air 10 Air 11 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 List Mode 5 ► ► ► ► ► ► ► ► Return Move Enter Delete All Page Return Channel List /Added DTV Air 2 DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Move Watch DTV Air 9-1 Add Air 10 Delete FavoriteAir 11 Air 16 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 RETURN List Mode Enter Delete All Return FAV.CH English - 39 BN68-01192F-02Eng-1.indd 39 2007-02-26 ソタネト 3:18:58 Viewing the Channel Lists You can display a list of all channels, added channels or your favorite channels. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 Press the ▲ or ▼ button to select Channel List, then press the ENTER button. 3 Press the ▲ or ▼ button to select All, Added or Favorite, then press the ENTER button. TV Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter TV ► ► ► ► ► ► ► ► Return Channel List All Added Favorite Default List Mode To toggle between your all channels, add channels, or favorite channels, use the red (P.MODE) button on the remote control. • Red (P.MODE) button: Press repeatedly to select All, Added, or Favorite. • Yellow (STILL) button: Press to delete all channels memorized. Move ► ► ► ► : All Return Enter Channel List /Added DTV Air 2 DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Move Air 18 DTV Air 9-1 Air 10 Air 11 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 RETURN List Mode Delete All Page Enter Return FAV.CH Setting the Default Channel List Mode You can set All, Added, or Favorite to be the Default List that appears when you press the CH LIST button. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 Press the ▲ or ▼ button to select Channel List, then press the ENTER button. 3 Press the ▲ or ▼ button to select Default List Mode, then press the ENTER button. Press the ▲ or ▼ button to select All, Added, or Favorite, then press the ENTER button. ➢ Select the Channel list you want to appear when you press the CH LIST button. • All: Shows All the channels when you press the CH LIST button on the remote control. • Added: Shows Added channels when you press CH LIST button on the remote control. • Favorite: Shows Favorite channels when you press CH LIST button on the remote control. Press the EXIT button to exit. TV Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter TV ► ► ► ► ► ► ► ► Return Channel List All Added Favorite Default List Mode Move All : All Added Favorite Enter Return Press the CH LIST button on the remote control to bring up the Channel Lists. English - 40 BN68-01192F-02Eng-1.indd 40 2007-02-26 ソタネト 3:19:03 Labeling Channels Channels can labeled so that their call letters appear whenever the channel is selected. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. Press the ▲ or ▼ button to select Name, then press the ENTER button. 2 Press the ▲ or ▼ button to select the channel to be assigned a new name, then press the ENTER button. 3 Press the ▲ or ▼ button to select a letter, a number or a blank (Results in this sequence: A~Z, 0~9, +, -, *, /, blank). Press the ► button to switch to the next field, which will be selected. Select a second letter or digit by pressing the ▲ or ▼ button, as above. Repeat the process to select the last three digits. When you have finished, press the ENTER button to assign the new name. To erase the assigned new name, select Clear by pressing the ◄ or ► button, then press the ENTER button. TV Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter TV ► ► ► ► ► ► ► ► Return Name Clear Clear Clear Clear Clear Air 6 Air 7 Air 9 Air 11 Air 13 ▼ TV Name ▲ Air 6 Air 7 Air 9 Air 11 Air 13 Press the EXIT button to exit. ➢ The names of digital broadcasting channels are automatically assigned and thus cannot be assigned by users. Return Enter Move Clear Clear Clear Clear Clear A ▼ ▼ Return Adjust Move Fine Tuning Analog Channels Use fine tuning to manually adjust a particular channel for optimal reception. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 Press the ▲ or ▼ button to select Fine Tune, then press the ENTER button. 3 Press the ◄ or ► button to adjust the fine tuning. 4 TV Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter ► ► ► ► ► ► ► ► Return Fine Tune To store the fine tuning setting in the TV’s memory, press the ENTER button. To reset the fine tuning setting, press the ▼ button to select Reset, then press the ENTER button. Press the EXIT button to exit. ➢ Only analog TV channels can be fine tuned. ➢ “ * ” will appear next to the number of fine-tuned channels. Air 4 0 Reset Adjust Save Return Fine Tune Air 4 * Fine Tuned 10 Reset Adjust Save Return Fine Tune Air 4 0 Reset Move Enter Return English - 41 BN68-01192F-02Eng-1.indd 41 2007-02-26 ソタネト 3:19:08 Checking the Digital-Signal Strength Unlike analog channels, which can vary in reception quality from “snowy” to clear, digital (HDTV) channels have either perfect reception quality or you will not receive them at all. So, unlike analog channels, you cannot fine tune a digital channel. You can, however, adjust your antenna to improve the reception of available digital channels. 1 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. TV Press the ▲ or ▼ button to select Signal Strength, then press the ENTER button. If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength. Continue to adjust the antenna until you find the best position with the strongest signal. Press the EXIT button to exit. Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter TV ► ► ► ► ► ► ► ► Return Signal Strength You can also press the ENTER button to select OK then press the EXIT button to exit the menu. OK Enter Return LNA (Low Noise Amplifier) If the TV is operating in a weak-signal area, sometimes the LNA function can improve the reception (a low-noise preamplifier boosts the incoming signal). 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. 2 Press the ▲ or ▼ button to select LNA, then press the ENTER button. 3 Press the ▲ or ▼ button to select Off or On, then press the ENTER button. Press the EXIT button to exit. LNA functions only when antenna is set to Air. (See “Selecting the Antenna” on page 38) ➢ If the picture is noisy with the LNA set to On, select Off. ➢ The LNA setting must be made separately for each channel. ➢ TV Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength LNA : On Move Enter TV ► ► ► ► ► ► ► ► Return Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Off Signal Strength On LNA : On Move Enter Return English - 42 BN68-01192F-02Eng-1.indd 42 2007-02-26 ソタネト 3:19:10 PC Display Using Your TV as a Computer (PC) Display Setting Up Your PC Software (Based on Windows XP) The Windows display-settings for a typical computer are shown below. The actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. However, even if your actual screens look different, the same basic set-up information will apply in almost all cases. (If not, contact your computer or Video Card manufacturer.) 1 2 First, click on Control Panel on the Windows start menu. When the control panel window appears, click on Appearance and Themes and a display dialog-box will appear. When the control panel window appears, click on Display and a display dialogbox will appear. Navigate to the Settings tab on the display dialog-box. The correct size setting (resolution) Optimum: 1024 x 768 pixels If a vertical-frequency option exists on your display settings dialog box, the correct value is 60 or 60 Hz. Otherwise, just click OK and exit the dialog box. 3 4 Display Modes If the signal from the system equals the standard signal mode, the screen is adjusted automatically. If the signal from the system doesn’t equal the standard signal mode, adjust the mode by referring to your videocard user guide; otherwise there may be no video. For the display modes listed below, the screen image has been optimized during manufacture. D-Sub Input Resolution 720 x 400 VGA SVGA XGA WXGA 640 x 480 800 x 600 1024 x 768 1360 x 768 Vertical Frequency (Hz) Horizontal Frequency (kHz) Vertical Polarity Horizontal Polarity HP-T4254 HP-T5054 70.087 31.469 N P ✔ ✔ 59.940 31.469 N N ✔ ✔ 72.809 37.861 N N ✔ ✔ 75.000 37.500 N N ✔ ✔ 60.317 37.879 P P ✔ ✔ 72.188 48.077 P P ✔ ✔ 75.000 46.875 P P ✔ ✔ 60.004 48.363 N N ✔ ✔ 70.069 56.476 N N ✔ ✔ 75.029 60.023 P P ✔ ✔ 60.015 47.712 P P ✔ HDMI/DVI Input Resolution Vertical Frequency (Hz) Horizontal Frequency (kHz) Vertical Polarity Horizontal Polarity HP-T4254 HP-T5054 720 x 400 70.087 31.469 N P ✔ ✔ 640 x 480 59.940 31.469 N N ✔ ✔ SVGA 800 x 600 60.317 37.879 P P ✔ ✔ XGA 1024 x 768 60.004 48.363 N N ✔ ✔ WXGA 1360 x 768 60.015 47.712 P P VGA • • • • ✔ The interlace mode is not supported. The TV operates abnormally if a non-standard video format is selected. The table above conforms to IBM/VESA regulations and is based on using the Analog Input. “ ✔ ” mark means that this mode can be supported. ➢ • For the HP-T4254, PC text quality is optimum in XGA mode (1024 x 768@60Hz). • For the HP-T5054, PC text quality is optimum in WXGA mode (1360 x 768@60Hz). (Three pixels on left, right, top and bottom will be grayed out at the resolution setting of 1360x768@60Hz. This is not a mechanical problem but a result caused by the pixel difference between the standard resolution and the PDP panel.) • When this TV is used as a PC display, 32-bit color is supported. • Depending on the manufacturer, your PC display screen might appear different. (and depending on your particular version of Windows.) Check your PC instruction book for information about connecting your PC to a TV. • If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.4KHz (horizontal). • In some cases, abnormal signals (such as stripes) might appear on the TV screen when the PC power is turned off (or if the PC is disconnected). If so, press the SOURCE button on the remote control or TV panel to enter a VIDEO mode. Also, make sure that the PC is connected. English - 43 BN68-01192F-02Eng-1.indd 43 2007-02-26 ソタネト 3:19:10 Setting up the TV with your PC Use the Auto Adjust function to have the TV set automatically adjust the video signals it receives from the PC. The function also automatically fine-tunes the settings and adjusts the frequency values and positions. How to Auto Adjust 1 2 TV Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select PC, then press the ENTER button. Press the ▲ or ▼ button to select Auto Adjustment, then press the ENTER button. The message Auto Adjustment in progress. Please wait. appears on the screen and the picture adjustments are automatically activated. Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ TV ► ► ► : Off ► : In Watching TV ► : Off ► : Off : Medium Enter Return PC Image Lock Position Auto Adjustment Image Reset Press the EXIT button to exit. ➢ This function does not work in DVI-Digital mode. ➢ Change to the PC mode first. Move ► ► Enter Return Auto Adjustment in progress. Please wait. Adjusting the Screen Quality The purpose of the picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by fine tuning alone, then do the frequency adjustments to the utmost and fine tune again. After the noise has been reduced, re-adjust the picture so that it is aligned on the center of the screen. ➢ Change to the PC mode first. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select PC, then press the ENTER button. 2 Press the ENTER button to select Image Lock. 3 Press the ▲ or ▼ button to select Coarse or Fine, then press the ENTER button. Press the ◄ or ► button to adjust the screen quality, then press the ENTER button. TV PC Image Lock Position Auto Adjustment Image Reset Move TV ► ► Enter Return Image Lock Coarse Fine Press the EXIT button to exit. ➢ This feature may change the width of the image. If necessary, adjust the position to center. 50 0 Move Enter Return Coarse 50 Move Adjust Return Continued... English - 44 BN68-01192F-02Eng-1.indd 44 2007-02-26 ソタネト 3:19:12 Changing the Screen Position After connecting the TV to your PC, adjust the position of the screen if it is not well-aligned. ➢ Change to the PC mode first. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select PC, then press the ENTER button. 2 Press the ▲ or ▼ button to select Position, then press the ENTER button. 3 Press the ▲ or ▼ button to adjust the V-Position. Press the ◄ or ► button to adjust the H-Position. Press the ENTER button. TV PC Image Lock Position Auto Adjustment Image Reset ► ► Move TV Enter Return Position Press the EXIT button to exit. Enter Adjust Return Initializing the Screen Position TV ➢ Change to the PC mode first. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select PC, then press the ENTER button. 2 Press the ▲ or ▼ button to select Image Reset, then press the ENTER button. The message Image Reset is completed. appears on the screen. PC Image Lock Position Auto Adjustment Image Reset ► ► Move Press the EXIT button to exit. The previously adjusted settings will be reset to the factory defaults. Enter Return Image Reset is completed. ➢ Setting the Home Theater PC This function enables you to view higher quality pictures while in PC Mode. After setting the Home Theater PC function to On, you can go into the Detailed Settings menu and make adjustments without affecting settings in the regular TV mode. 1 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select Home Theater PC, then press the ENTER button. TV Press the ▲ or ▼ button to select Off or On, then press the ENTER button. Press the EXIT button to exit. ➢ This function is available only in PC mode. Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ TV ► ► ► : Off ► : In Watching TV ► : Off ► : Off : Medium Enter Return Setup ▲ More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move : Off : Medium Off : Off Watching TV : InOn : Off Enter Return English - 45 BN68-01192F-02Eng-1.indd 45 2007-02-26 ソタネト 3:19:14 Time Setting Setting the Time Setting the clock is necessary in order to use the various timer features of the TV. Also, you can check the time while watching the TV. (Just press the INFO button.) Option 1: Setting the Clock Manually 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select Time, then press the ENTER button. 2 Press the ENTER button to select Clock. TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move 3 Press the ENTER button to select Clock Mode. Press the ▲ or ▼ button to select Manual, then press the ENTER button. TV : Off : Medium Time : Off : Inactivated : Inactivated : Inactivated Move Press the ▲ or ▼ button to select Clock Set, then press the ENTER button. TV Enter TV : Off Enter Return Clock Clock Mode Clock Set Time Zone DST Press the EXIT button to exit. ➢ The current time will appear every time you press the INFO button. ➢ You can set the Month, Day, Year, Hour, and Minute directly by pressing the number buttons on the remote control. Return : Auto Manual Auto Move Press the ◄ or ► button to move to Month, Day, Year, Hour, Minute, or am/ pm. Set the date and time you want by pressing the ▲ or ▼ button, then press the ENTER button. ► ► ► ► ► Clock Clock Mode Clock Set Time Zone DST 5 Return Enter --/ --/ ----/ -- : -- -Clock Sleep Timer Timer1 Timer2 Timer3 4 ► ► ► ► ► ► ► : English : Manual : Off Move TV ► ► ► ► Enter Return Clock Set Set current date and time. Month Day -- -- ---- Hour Minute am/pm -- -- -- Move Year Adjust Return Continued... English - 46 BN68-01192F-02Eng-1.indd 46 2007-02-26 ソタネト 3:19:17 Option 2: Setting the Clock Automatically The Clock can be set automatically if you are receiving a digital signal. 1 2 TV Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select Time, then press the ENTER button. Press the ENTER button to select Clock. Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV ► ► ► ► ► ► ► : English : Off : Medium Enter Return Time --/ --/ ----/ -- : -- -Clock Sleep Timer Timer1 Timer2 Timer3 Move 3 Press the ENTER button to select Clock Mode. Press the ▲ or ▼ button to select Auto, then press the ENTER button. TV Press the ▲ or ▼ button to select Time Zone, then press the ENTER button. 5 Press the ▲ or ▼ button to highlight the time zone for your local area (and to move the highlight to the appropriate time zone on the map of the United States), then press the ENTER button. TV Press the ▲ or ▼ button to select DST (Daylight Saving Time), then press the ENTER button. Press the ▲ or ▼ button to select On or Off, then press the ENTER button. Press the EXIT button to exit. ➢ Depending on the broadcast station and signal, the auto time may not be set correctly. If this occurs, set the time manually. ➢ Antenna or Cable must be connected in order to set the time automatically. Return : Auto Manual Auto : Off Enter Return Time Zone Select the time zone in which you live. Newfoundland Atlantic Eastern Central Mountain Pacific Alaska Hawaii Move 6 Enter ► ► ► ► ► Clock Clock Mode Clock Set Time Zone DST Move 4 : Off : Inactivated : Inactivated : Inactivated TV Enter Return Clock Clock Mode Clock Set Time Zone DST Move : Auto : Off On Off Enter Return Continued... English - 47 BN68-01192F-02Eng-1.indd 47 2007-02-26 ソタネト 3:19:19 Setting the On/Off Timer Use this feature to set the TV to turn on or off at a desired time. You must set the clock first. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select Time, then press the ENTER button. 2 Press the ▲ or ▼ button to select Timer1, Timer2,or Timer3, then press the ENTER button. The timer menu is displayed. Press the ▲ or ▼ button to adjust hour, then press the ► button to move to the next step. Set other items using the same method as above. 3 TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV ➢ Auto Power Off When you set the timer On, the television will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by timer. This function is only available in timer On mode and prevents overheating, which may occur if a TV is on for too long time. Return Enter On Time 12 : 0 am Inactivate Off Time 12 : 0 am Inactivate Volume 10 Once Repeat Contents TV Air 3 Return Adjust Contents Source TV Antenna Cable Channel Music None Photo None Move 3 Return Adjust Time 1/ 1/ 2007/ 12 : 04 am The sleep timer automatically shuts off the TV after a preset time (30, 60, 90, 120, 150 and 180 minutes). 1 ► ► ► ► ► Timer 1 TV Setting the Sleep Timer Return Enter : Off : Inactivated : Inactivated : Inactivated Move Move ➢ : Medium 1/ 1/ 2007/ 12 : 04 am Clock Sleep Timer Timer1 Timer2 Timer3 Press the EXIT button to exit. You can set the hour, and minute directly by pressing the number buttons on the remote control. : Off Time Press the ◄ or ► button to select the desired item below. Press the ▲ or ▼ button to adjust the setting. • On Time: Select hour, minute, am/pm, and Inactivated/Activated. (To activate the On Time, set to Activated.) • Off Time: Select hour, minute, am/pm, and Inactivated/Activated. (To activate Off time, set to Activated.) • Repeat: Select Once, Everyday, Mon~Fri, Mon~Sat, or Sat~Sun. • Volume: Select the volume level you want the TV to be at when it turns on with the Timer. • Contents: When the On Timer is active, you can turn on a specific channel or play back contents such as photo or audio files. (Make sure that an USB device is connected to your TV.) ► ► ► ► ► ► ► : English Clock Sleep Timer Timer1 Timer2 Timer3 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select Time, then press the ENTER button. : Off : Inactivated : Inactivated : Inactivated Move TV Enter ► ► ► ► ► Return Sleep Timer Set sleep timer. 2 Press the ▲ or ▼ button to select Sleep Timer, then press the ENTER button. Minute Activation --- Off ▼ Move TV 3 Press the ▲ or ▼ button to select the minute. Setting the Timer sets the Activation to On automatically. To cancel the set sleep timer: Press the ► button to select Activation. Press the ▲ or ▼ button to select Off, then press the ENTER button. Press the EXIT button to exit. ▲ Adjust Return Sleep Timer Set sleep timer. Minute Activation 30 On Move Adjust ▲ RETURN ▼ Return FAV.CH Press the SLEEP button on the remote control until the a ppropriate time interval appears (any of the preset values from 30 min to 180 min). English - 48 BN68-01192F-02Eng-1.indd 48 2007-02-26 ソタネト 3:19:23 Function Description Selecting a Menu Language Setting the clock is necessary in order to use the various timer features of the TV. Also, you can check the time while watching the TV. (Just press the INFO button.) 1 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select Language, then press the ENTER button. Press the ▲ or ▼ button to select the appropriate language: English, Español, or Français, then press the ENTER button. TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV : Off : Medium Enter Return Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move Press the EXIT button to exit. ► ► ► ► ► ► ► : English English : English Español Français : Off : Medium Enter Return Using the Game Mode When connecting to a game console such as PlayStationTM or XboxTM, you can enjoy a more realistic gaming experience by selecting game menu. 1 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. TV Press the ▲ or ▼ button to select Game Mode, then press the ENTER button. 3 Select Off or On by pressing the ▲ or ▼ button, then press the ENTER button. 4 Press the EXIT button to exit. ➢ Restrictions on Game mode (Caution) • To disconnect the game console and connect another external device, set Game to Off in the setup menu. • If you display the TV menu in Game mode, the screen shakes slightly. • The mark ( ) appears on the screen which means that Game Mode is on with the selected source. If ➢ Game Mode is On • Picture Mode is automatically changed to Game and cannot be changed. • Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer. • The Reset in the Sound menu is activated. Reset function initializes the Equalizer settings to the factory default setting. ➢ Game Mode is not available in regular TV/Antenna mode. ➢ If the picture is poor when external device is connected to TV, check if Game Mode is On. Set Game Mode to Off and connect external devices. Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV ► ► ► ► ► ► ► : English : Off : Medium Enter Return Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move : English : Off On Off : Medium Enter Return AV1 Game Mode English - 49 BN68-01192F-02Eng-1.indd 49 2007-02-26 ソタネト 3:19:27 Viewing Closed Captions (On-Screen Text Messages) - Digital The Digital Captions function operates on digital channels. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select Caption, then press the ENTER button. 3 Press the ENTER button to select Caption. Press the ▲ or ▼ button to select On, then press the ENTER button. 4 Press the ▲ or ▼ button to select Caption Mode, then press the ENTER button. Press the ▲ or ▼ button to select submenu (Default, Service1~Service6, CC1~CC4 or Text1~Text4) you want, then press the ENTER button. TV TV Press the ▲ or ▼ button to select Size, then press the ENTER button. Press the ▲ or ▼ button to select the desired caption option, then press the ENTER button. Press the ▲ or ▼ button to select the desired sub-menu options (see options below), then press the ENTER button. Press the EXIT button to exit. ➢ The availability of captions depends on the program being broadcast. ➢ Default means to follow the standard set by the broadcaster. ➢ Foreground and Background cannot be set to have the same color. ➢ Foreground Opacity and Background Opacity cannot be both set to Transparent. • Size: This option consists of Default, Small, Standard, and Large. The default is Default. • Font Style: This option consists of Default, Style0 ~ Style7. You can change the font you want. The default is Default. • Foreground Color: This option consists of Default, White, Black, Red, Green, Blue, Yellow, Magenta, and Cyan. You can change the color of the letter. The default is Default. • Background Color: This option consists of Default, White, Black, Red, Green, Blue, Yellow, Magenta, and Cyan. You can change the background color of the caption. The default is Default. • Foreground Opacity: This option consists of Default, Transparent, Translucent, Solid, and Flashing. You can change the opacity of the letter. • Background Opacity: This option consists of Default, Transparent, Translucent, Solid, and Flashing. You can change the background opacity of the caption. • Return to Default: This option sets each of Size, Font Style, Foreground Color, Background Color, Foreground Opacity, and Background Opacity to its default. Press the CAPTION button on the remote control to select On or Off. ► ► ► ► ► ► ► : English : Off : Medium Enter Return Caption Caption : Off Off Caption Mode : Default On Caption Options 5. Press the ▲ or ▼ button to select Caption Options, then press the ENTER button. 6 Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move Move TV Enter Return Caption Caption : On Caption Mode : Default Caption Options Move TV Enter ► ► ► Return Caption Caption : Off Default Caption Mode : Default Service1 Caption Options Service2 Service3 Service4 Service5 Service6 CC1 ▼ Move TV Enter Caption Caption : On Caption Mode : Default Caption Options Move TV Enter ► ► ► Return Caption Options Size Font Style Foreground Color Background Color Foreground Opacity Background Opacity Return to Default : Default : Default : Default : Default : Default : Default ► ► ► ► ► ► ► RETURN Move Enter Return FAV.CH English - 50 BN68-01192F-02Eng-1.indd 50 2007-02-26 ソタネト 3:19:30 Viewing Closed Captions (On-Screen Text Messages) - Analog The Analog Caption function operates in either analog TV channel mode or external signal mode. (Depending on the broadcasting signal, the Analog Caption function may operate on digital channels.) 1 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move Press the ▲ or ▼ button to select Caption, then press the ENTER button. TV ► ► ► ► ► ► ► : English : Off : Medium Enter Return Caption Caption : Off Off Caption Mode : Default On Caption Options 3 Press the ENTER button to select Caption. Press the ▲ or ▼ button to select On, then press the ENTER button. Move TV Press the ▲ or ▼ button to select Caption Mode, then press the ENTER button. Press the ▲ or ▼ button to select submenu (CC1~CC4 or Text1~Text4) you want, then press the ENTER button. Press the EXIT button to exit. TV • The Caption feature doesn’t work in COMPONENT, PC, HDMI(DVI) modes. • The availability of captions depends on the program being broadcast. You can also press the CAPTION button on the remote control to select Captions On or Off. Enter ► ► ► Return Caption Default Caption : Off CC1 Caption Mode : Default CC2 Caption Options CC3 CC4 Text 1 Text 2 Text 3 Text 4 • The default is Default. • CC1: The Primary Synchronous Caption Service. These are captions in the primary language that must be in sync with the sound, preferably matched to a specific frame. • CC2: The Special Non-Synchronous Use Captions.This channel carries data that is intended to augment information carried in the program. • CC3: Secondary Synchronous Caption Service. Alternate program-related caption data, typically second language captions. • CC4: Special Non-Synchronous Use Captions. Similar to CC2. • Text1: First Text Service. This may be various non-program related data. • Text2: Second Text Service. Additional data, usually not program related. • Text3/Text4: Third and Fourth Text Services. These data channels should be used only if Text1 and Text2 are not sufficient. ➢ Return Caption : On Caption Mode : Default Caption Options Move 4 Enter Caption Move Enter Return RETURN FAV.CH English - 51 BN68-01192F-02Eng-1.indd 51 2007-02-26 ソタネト 3:19:33 Menu Transparency Level Adjusts the transparency of the menu screen. 1 2 3 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. TV Press the ▲ or ▼ button to select Menu Transparency, then press the ENTER button. Press the ▲ or ▼ button to select level, then press the ENTER button. Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV : Off : Medium Enter Return Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move Press the EXIT button to exit. ► ► ► ► ► ► ► : English : English : Off High Medium Low Opaque : Medium Enter Return Setting the Light Effect You can turn the blue LED on the front of TV on/off. 1 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. TV Press the ▲ or ▼ button to select Light Effect, then press the ENTER button. Press the ▲ or ▼ button to select Off, In Standby, In Watching TV, or Always, then press the ENTER button. Press the EXIT button to exit. • Off: The LED is always off. • In Standby: The LED lights while in Standby mode and it turns off when your TV is turned on. • In Watching TV: The LED lights when watching TV and it turns off when your TV is turned off. • Always: The LED is always lit. ➢ Set the Light Effect to Off to reduce the power consumption. Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ TV ► ► ► : Off ► : In Watching TV ► : Off ► : Off : Medium Enter Return Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ : Off : Medium Off In Standby : Off Watching TV TV : InInWatching Always : Off Enter Return English - 52 BN68-01192F-02Eng-1.indd 52 2007-02-26 ソタネト 3:19:36 Using the Energy Saving Feature This feature adjusts the power consumption of the unit in order to save energy. 1 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. TV Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ Press the ▲ or ▼ button to select Energy Saving, then press the ENTER button. Press the ▲ or ▼ button to select Off, Low, Medium, or High, then press the ENTER button. Press the EXIT button to exit. TV • Off: Switches off the Energy Saving mode. • Low: Operates in standard mode. • Medium: Enters medium power saving mode. • High: Enters maximum power saving mode. ► ► ► : Off ► : In Watching TV ► : Off ► : Off : Medium Enter Return Setup More Blue Screen Melody PC Home Theater PC Light Effect Energy Saving ▼ More Move ▲ : Off : Medium Off : Off Low Watching TV : InMideum High : Off Enter Return Preventing Screen Burn-in To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to program the time between movement of the picture in minutes. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select Screen Burn Protection, then press the ENTER button. 3 Press the ENTER button to select Pixel Shift, then press the ENTER button. Pressing the ▲ or ▼ button will alternate between On and Off. You will also see the items Horizontal Dot, Vertical Line and Time. TV Setup More Screen Burn Protection ► HDMI Black Level : Normal ► Film Mode : Off ► Wall-Mount Adjustment ► PIP ► Function Help : On ► SW Upgrade ► Move Enter Return ▲ TV Screen Burn Protection Pixel Shift White Scroling Side Gray ► ► ► ► : Dark • Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to prevent after-images on the screen. Move 4 Press the ▲ or ▼ button to select the item you wish to change, then press the ENTER button. Press the ▲ or ▼ button to change the value of the item, then press the ENTER button. TV Enter Return Pixel Shift Pixel Shift Horizontal Dot Vertical Line Time : On Off : 2On :2 :2 • Optimum condition for pixel shift; PC Horizontal Dot Vertical Line Time(min) 1 1 2 TV/AV1/AV2/S-Video/ Component/HDMI 2 2 2 Move TV Pixel Shift Horizontal Dot Vertical Line Time Press the EXIT button to exit. Enter Return Pixel Shift Move : On : 20 : 21 : 22 3 4 Enter Return English - 53 BN68-01192F-02Eng-1.indd 53 2007-02-26 ソタネト 3:19:39 Reducing the Effects of Screen Burn If screen burn has occurred, you can select a white screen or scroling to help remove screen burn artifacts. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select Screen Burn Protection, then press the ENTER button. 3 Press the ▲ or ▼ button to select White, Scroling, or Side Gray then press the ENTER button. Press the EXIT button to exit. White This function removes after-images on the screen by changing the color of pixels to white. Use this function when there are remaining after-images or symbols on the screen especially when you displayed a still image on the screen for a long time. TV Move TV Move TV ➢ ➢ : Dark Enter Return ► ► ► ► : Dark Enter Return Screen Burn Protection Pixel Shift White Scroling Side Gray • Dark: When you set the screen ratio to 4:3, it darkens the left and right sides. • Light: When you set the screen ratio to 4:3, it brightens the left and right sides. ➢ ► ► ► ► Screen Burn Protection Pixel Shift White Scroling Side Gray Scroling This function removes after-images on the screen by moving all the pixels on the PDP according to a pattern. Use this function when there are remaining after-images or symbols on the screen especially when you displayed a still image on the screen for a long time. Side Gray When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides. To prevent the screen burn from happening, select Dark or Light. Screen Burn Protection Pixel Shift White Scroling Side Gray Move To remove after-images on the screen, use either the White or Scroling function. Although both functions remove after-images on the screen, Scroling is more effective. The after-image removal function has to be executed for a long time (approximately 1 hour) to effectively remove after-images on the screen. If the after-image is not removed after performing the function, repeat the function again. Press any key on the remote control to cancel this feature. ► : Dark Dark Light Enter Return Setting the Function Help Displays help on the menu functions. TV 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select Function Help, then press the ENTER button. 3 Press the ▲ or ▼ button to select Off or On, then press the ENTER button. Press the EXIT button to exit. ➢ The Function Help default setting is On. Setup More Screen Burn Protection ► HDMI Black Level : Normal ► Film Mode : Off ► Wall-Mount Adjustment ► PIP ► Function Help : On ► SW Upgrade ► Move Return Enter ▲ TV Setup More Screen Burn Protection HDMI Black Level : Normal : Off Film Mode Wall-Mount Adjustment PIP Off Function Help : On On SW Upgrade Move Return Enter ▲ English - 54 BN68-01192F-02Eng-1.indd 54 2007-02-26 ソタネト 3:19:42 Wall- mount adjustment (Sold separately) Once the wall mount is installed, the position of your TV can be easily adjusted. Auto Wall-Mount TV Rear Panel EX-LINK Cable (Not supplied) Entering the menu 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select Wall-Mount Adjustment, then press the ENTER button. 3 Adjust to the desired position using the ▲/▼/◄/► buttons. TV Setup More Screen Burn Protection ► HDMI Black Level : Normal ► Film Mode : Off ► Wall-Mount Adjustment ► PIP ► Function Help : On ► SW Upgrade ► Move Return Enter ▲ Press the EXIT button to exit. Wall-Mount Adjustment ➢ If you press an arrow button when no OSD is displayed on the TV screen, the Adjustment screen appears. ➢ When you turn the power off, your TV moves to the initial installation position. When you turn the power on, your TV moves to the last remembered position you adjusted. Position1 Position Adjust 1 INFO 2 Center 3 Exit Using the remote Control Buttons Button ➢ ➢ ➢ Operations Wall-mount angle adjustment Tilt Up, Tilt Down, Move right, Move left Reset Moves to the initial installation position Remembering the position and moving to the remembered position Remembers 3 positions with the Red, Green and Yellow buttons. Moves to the remembered position using these 3 color buttons. For installation, refer to the Installation Manual provided. For product installation and the installation and moving of the wall mount, make sure to consult a specialized installation company. This installation manual is to be used when attaching the wall mount to a wall. When attaching to other building materials, please contact your nearest dealer English - 55 BN68-01192F-02Eng-1.indd 55 2007-02-26 ソタネト 3:19:45 Upgrading the Software Samsung may offer upgrades for your TV’s firmware in the future. Please contact the Samsung call center at 1-800-SAMSUNG to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on the side of your TV. 1 Insert a USB drive containing the firmware upgrade into the USB Upgrade Port on the side of the TV. 2 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 3 Press the ▲ or ▼ button to select SW Upgrade, then press the ENTER button. 4 Press the ▲ or ▼ button to select USB, then press the ENTER button. The message Scanning for USB... It may take up to 30 seconds. is displayed. 5 ��������� TV If the firmware on the USB is properly recognized, the message Upgrade version xxxx to version xxxx? The system would be reset after upgrade. is displayed. Press the ◄ or ► button to select OK, then press the ENTER button. The upgrade starts. Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will shut off and turn on automatically after completing the firmware upgrade. Please check the firmware version after the upgrades are complete. ➢ The firmware and upgrade process may be different by country and region. Setup More Screen Burn Protection HDMI Black Level : Normal Film Mode : Off Wall-Mount Adjustment PIP Function Help : On SW Upgrade Move Enter ▲ TV ► ► ► ► ► ► ► Return SW Upgrade USB ► Move Enter Return SW Upgrade Scanning for USB... It may take up to 30 seconds. SW Upgrade Upgrade version XXXX to version XXXX ? The system would be reset after upgrade. OK Cancel Using the V-Chip The V-Chip feature automatically locks out programs that are deemed inappropriate for children. The user must enter a PIN (personal ID number) before any of the V-Chip restrictions are set up or changed. ➢ ➢ ➢ When the V-Chip feature is activated, the PIP features do not function. The V-Chip does not work if the input is Digital TV (HD or SD). V-Chip function is not available in HDMI or component mode. TV Setting Up Your Personal ID Number (PIN) 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select V-Chip, then press the ENTER button. The message Enter PIN will appear. Enter your 4 digit PIN number. ➢ The default PIN number of a new TV set is 0-0-0-0. Continued... Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV ► ► ► ► ► ► ► : English : Off : Medium Enter Return V-Chip Enter PIN * * * 0~9 Enter PIN * Return English - 56 BN68-01192F-02Eng-1.indd 56 2007-02-26 ソタネト 3:19:57 3 The V-Chip screen will appear. Press the ▲ or ▼ button to select Change PIN, then press the ENTER button. The Change PIN screen will appear. Choose any 4 digits for your PIN and enter them. Re-enter the same 4 digits. When the message PIN is changed successfully. is displayed, your PIN has been memorized. TV V-Chip V-Chip Lock : Off TV Parental Guidelines MPAA Rating Downloadable U.S. Rating Change PIN ► ► ► ► ► Press the EXIT button to exit. ➢ If you forget the PIN, press the remote-control buttons in the following sequence, which resets the pin to 0-0-0-0 : Power Off. → MUTE → 8 → 2 → 4 → Power On. Move Enter Return <for USA models only> TV V-Chip V-Chip Lock : Off TV Parental Guidelines MPAA Rating Canadian English Canadian French Downloadable U.S. Rating Change PIN Move Enter ► ► ► ► ► ► ► Return <for Canada models only> TV Change PIN Enter new PIN Confirm new PIN Return 0~9 Enter PIN How to Enable/Disable the V-Chip 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select V-Chip, then press the ENTER button. The message Enter PIN will appear. Enter your 4 digit PIN number. TV V-Chip Enter PIN * * * * Return 0~9 Enter PIN 3 ➢ The V-Chip screen will appear. To enable the V-Chip feature, press the ENTER button so that the V-Chip Lock field is On. (Pressing the ▲ or ▼ button will alternate between On and Off.) Press the ENTER button. While V-Chip is in operation, the Still function cannot be used. TV V-Chip V-Chip Lock : Off Off TV Parental Guidelines On MPAA Rating Canadian English Canadian French Downloadable U.S. Rating Change PIN Press the EXIT button to exit. Move Enter Return How to Set up Restrictions Using “TV Parental Guidelines” First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.) Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating. 1 TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. TV 2 Press the ▲ or ▼ button to select V-Chip, then press the ENTER button. The message Enter PIN will appear. Enter your 4 digit PIN number. Continued... ► ► ► ► ► ► ► : English : Off : Medium Enter Return V-Chip Enter PIN * * * * 0~9 Enter PIN Return English - 57 BN68-01192F-02Eng-1.indd 57 2007-02-26 ソタネト 3:20:01 3 The V-Chip screen will appear. Press the ▲ or ▼ button to select TV Parental Guidelines, then press the ENTER button. 4 The TV Parental Guidelines screen will appear. Press the ▲ or ▼ button to select one of the six aged based categories: • TV-Y: All children. The themes and elements in this program are specifically designed for a very young audience, including children from ages two to six. • TV-Y7: Directed to older children. The themes and elements in this program may include mild physical or comedic violence, or may frighten children under the age of seven. • TV-G: General audience. It contains little or no violence, no strong language, and little or no sexual dialog or situations. • TV-PG: Parental guidance suggested. This program may contain infrequent coarse language, limited violence, some suggestive sexual dialog and situations. • TV-14: Parents strongly cautioned. This program may contain sophisticated themes, sexual content, strong language and more intense violence. • TV-MA: Mature audiences only. This program may contain mature themes, profane language, graphic violence and explicit sexual content. 5 At this point, one of the TV-Ratings is selected. Press the ENTER button. Depending on your existing setup, the “ ” symbol will be selected. (Blank = Unblocked, = Blocked) While “ ” is selected, press the ENTER button to block or unblock the category. To select a different TV-Rating, press the ▲ or ▼ button and then repeat the process. ➢ Allow all: Press to unlock all TV ratings. Block all: Press to lock all TV ratings. ➢ The TV-Y, TV-Y7, TV-G, TV-PG, TV-14 and TV-MA have additional options. See the next step to change any of the following sub-ratings: • FV: Fantasy violence. • D: Sexually suggestive dialog. • L: Adult language. ➢ TV V-Chip V-Chip Lock : On TV Parental Guidelines MPAA Rating Canadian English Canadian French Downloadable U.S. Rating Change PIN Move TV Enter ► ► ► ► ► ► ► Return TV Parental Guidelines Allow All Block All Move Enter Return • S: Sexual situation. • V: Violence. The V-Chip will automatically block certain categories that are “more restrictive”. For example, if you block TV-Y category, then TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the categories in the “young adult” group will be blocked (TV-G, TV-PG, TV-14, and TV-MA). The subratings (D, L, S, V) work together similarly. (See next section.) 6 How to set the FV, D, L, S and V sub-ratings. First, select one of these TVRatings: TV-Y, TV-Y7, TV-G, TV-PG, TV-14, or TV-MA (See Step 4), and press the ENTER button. The “ ” symbol will be displayed for each sub-rating. While “ ” is selected, press the ► button to go to a sub rating. Press the ENTER to block the sub rating. To select a different TV-Rating, press the ▲ or ▼ button and then repeat the process. 7 Press the EXIT button to clear all the screens. (Or proceed to the next section, and set up additional restrictions based on the MPAA codes.) ➢ These categories consist of two separate groups: TV-Y and TV-Y7 (young children through age 7), and TV-G through TV-MA (everybody else). The restrictions for these two groups work independently: If a household includes very young children as well as young adults, the TV guidelines must be set up separately for each age group. Continued... English - 58 BN68-01192F-02Eng-1.indd 58 2007-02-26 ソタネト 3:20:03 How to Set up Restrictions Using “MPAA Ratings” (G, PG, PG-13, R, NC-17, X, NR ) The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main application is for movies. When the V-Chip lock is on, the TV will automatically block any programs that are coded with objectionable ratings (either MPAA or TV-Ratings). 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select V-Chip, then press the ENTER button. TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move The message Enter PIN will appear. Enter your 4 digit PIN number. TV ► ► ► ► ► ► ► : English : Off : Medium Return Enter V-Chip Enter PIN * 3 The V-Chip screen will appear. Press the ▲ or ▼ button to select MPAA Rating, then press the ENTER button. * Press the ▲ or ▼ button to select an appropriate restriction. Press the ENTER button to activate the restriction selected. The “ ” symbol is indicated. While “ ” is selected, press the ENTER button to block or unblock the category. Press the EXIT button to exit. ➢ Allow all: Press to unlock all TV ratings. Block all: Press to lock all TV ratings. Return V-Chip V-Chip Lock : On TV Parental Guidelines MPAA Rating Canadian English Canadian French Downloadable U.S. Rating Change PIN Move TV ► ► ► ► ► ► ► Return Enter MPAA Rating Allow All Block All • G: General audience (no restriction). • PG: Parental guidance suggested. • PG-13: Parents strongly cautioned. • R: Restricted. Children under 17 should be accompanied by an adult. • NC-17: No children under age 17. • X: Adults only. • NR: Not rated. ➢ * 0~9 Enter PIN TV 4 * Move Enter Return The V-Chip will automatically block any category that is “more restrictive”. For example, if you block the PG-13 category, then R, NC-17 and X will automatically be blocked also. How to Set up Restrictions Using “Canadian English” (for Canada Models) 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select V-Chip, then press the ENTER button. The message Enter PIN will appear. Enter your 4 digit PIN number. TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV ► ► ► ► ► ► ► : English : Off : Medium Enter Return V-Chip Enter PIN * Continued... * * * 0~9 Enter PIN Return English - 59 BN68-01192F-02Eng-1.indd 59 2007-02-26 ソタネト 3:20:06 3 The V-Chip screen will appear. Press the ▲ or ▼ button to select Canadian English, then press the ENTER button TV V-Chip V-Chip Lock : On TV Parental Guidelines MPAA Rating Canadian English Canadian French Downloadable U.S. Rating Change PIN Move 4 Press the ▲ or ▼ button to select an appropriate restriction. Press the ENTER button to activate the restriction selected. The “ indicated. ” symbol is Canadian English TV Allow All Block All • C: • C8+: • G: • PG: • 14+: Programming intended for children under age 8. Programming generally considered acceptable for children 8 years and over to watch on their own. General programming, suitable for all audiences. Parental guidance. Programming contains themes or content which may not be suitable for viewers under the age of 14. • 18+: Adult programming. Move Return Enter The V-Chip will automatically block any category that is “more restrictive”. For example, if you block G category, then PG, 14+ and 18+ will automatically be blocked also. How to Set up Restrictions Using “Canadian French” (for Canada Models) 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select V-Chip, then press the ENTER button. The message Enter PIN will appear. Enter your 4 digit PIN number. 3 The V-Chip screen will appear. Press the ▲ or ▼ button to select Canadian French, then press the ENTER button. 4 Press the ▲ or ▼ button to select an appropriate restriction. Press the ENTER button to activate the restriction selected. The “ indicated. TV • G: • 8 ans+: • 13 ans+: • 16 ans+: • 18 ans+: Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV ” symbol is : Off : Medium Return Enter V-Chip * * * * Return 0~9 Enter PIN General. Not recommended for young children. Programming may not be suitable for children under the age of 13. Programming is not suitable for children under the age of 16. Programming restricted to adults. The V-Chip will automatically block any category that is “more restrictive”. For example, if you block 8 ans+ category, then 13 ans+, 16 ans+ and 18 ans+ will automatically be blocked also. ► ► ► ► ► ► ► : English Enter PIN Press the EXIT button to exit. ➢ Allow all: Press to unlock all TV ratings. Block all: Press to lock all TV ratings. ➢ Return Enter Press the EXIT button to exit. ➢ Allow all: Press to unlock all TV ratings. Block all: Press to lock all TV ratings. ➢ ► ► ► ► ► ► ► TV V-Chip V-Chip Lock : On TV Parental Guidelines MPAA Rating Canadian English Canadian French Downloadable U.S. Rating Change PIN Move TV ► ► ► ► ► ► ► Enter Return Canadian French Allow All Block All Move Enter Return English - 60 BN68-01192F-02Eng-1.indd 60 2007-02-26 ソタネト 3:20:10 Using the V-Chip for Digital channels Parental restriction information can be used while watching DTV channels. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select V-Chip, then press the ENTER button. The message Enter PIN will appear. Enter your 4 digit PIN number. 3 4 The V-Chip screen will appear. Press the ▲ or ▼ button to select Downloadable U.S. Rating, then press the ENTER button. ➢ If information is not downloaded from the broadcasting station, the Downloadable U.S. Rating menu is deactivated. ➢ Parental restriction information is automatically downloaded while watching DTV channels. It may take several seconds. ➢ The Downloadable U.S. Rating menu is available for use after information is downloaded from the broadcasting station. However, depending on the information from the broadcasting station, it may not be available for use. Press the ▲ or ▼ button to select an appropriate restriction Press the ENTER button to activate the restriction selected. The “ ” symbol is indicated. Press the EXIT button to exit. Allow all: Press to unlock all TV ratings. Block all: Press to lock all TV ratings. ➢ Parental restriction levels differ depending on the broadcasting station. ➢ The default menu name and downloadable US rating changes depending on the downloaded information. ➢ Even if you set the on-screen display to your desired language, the Downloadable U.S. Rating menu will appear in English only. ➢ The rating will automatically block certain categories that are more restrictive. ➢ The rating titles (for example: Humor Level..etc) and TV ratings (for example: DH,MH,H..etc) may differ depending on the broadcasting station. TV Setup Plug & Play Language Time Game Mode V-Chip Caption Menu Transparency ▼ More Move TV ► ► ► ► ► ► ► : English : Off : Medium Return Enter V-Chip Enter PIN * * * * Return 0~9 Enter PIN TV V-Chip V-Chip Lock : On TV Parental Guidelines MPAA Rating Canadian English Canadian French Downloadable U.S. Rating Change PIN ➢ Move ► ► ► ► ► ► ► Enter Return The number of Rating title current rating information TV Downloadable U.S. Rating Humor Level ► 1/2 Allow All Block All DH MH H VH EH Move Enter Return The number of all the rating information How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”) If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following message will appear: 1 Enter your PIN. or To resume normal viewing, tune to a different channel using CH CH button. Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out all the channels. In this case, use the V-Chip function for an “emergency escape”: 1 Press the MENU button. Press the ▲ or ▼ button to select Setup, then press the ENTER button. 2 Press the ▲ or ▼ button to select V-Chip, then press the ENTER button. 3 Enter your PIN, then press the ENTER button, and press the ▲ or ▼ button to temporarily disable the V-Chip Lock. ➢ If you forget the PIN, press the remote-control buttons in the following sequence, which resets the pin to 0-0-0-0 : Power Off. → MUTE → 8 → 2 → 4 → Power On. Channel Is Locked by TV-PG[ S ] Use the NUMBER buttons to enter your pin number to unlock all channels. Press EXIT to clear PIN. Press MENU for main menu. Channel Is Locked by TV-PG[ L ] Use the NUMBER buttons to enter your pin number to unlock all channels. Press EXIT to clear PIN. Press MENU for main menu. English - 61 BN68-01192F-02Eng-1.indd 61 2007-02-26 ソタネト 3:20:13 About Anynet+ What is Anynet+? Anynet+ is an AV network system that enables you to control all connected Samsung AV devices with your Samsung TV’s remote. Connecting Anynet+ Devices The Anynet+ system can be used only with Samsung AV devices that have the Anynet+ feature. To be sure your Samsung AV device has this feature, check if there is an Anynet+ mark on it. To directly connect to TV TV Anynet+ Device 1 Anynet+ Device 2 Anynet+ Device 3 HDMI 1.3 Cable HDMI 1.3 Cable Connect the [HDMI 1], [HDMI 2] or [HDMI 3] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. HDMI 1.3 Cable To connect to Home Theater TV Anynet+ Device 1 HDMI 1.3 Cable HDMI 1.3 Cable Anynet+ Device 3 Home Theater Optical Cable ➢ ➢ ➢ ➢ ➢ ➢ HDMI 1.3 Cable Anynet+ Device 2 1. Connect the [HDMI 1], [HDMI 2] or [HDMI 3] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. 2. Connect the HDMI IN jack of the home theater and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable. HDMI 1.3 Cable Connect the Optical cable between [Digital Audio Out (Optical)] on your TV and Digital Audio Input on the Home Theater. Connect only one Home Theater. You can listen to 5.1 channel sound through the home theater’s speakers. Otherwise, you can only listen to 2 channel stereo sound in other cases. Make sure to connect the Digital Audio IN (Optical) of the home theater and the TV correctly to listen to TV sound through the home theater. However, you cannot listen to sound from the BD recorder that is sent to the home theater via the TV in 5.1 channel sound because the TV outputs only 2 channel stereo sound. Please see the manual for the home theater. You can connect an Anynet+ device using the HDMI 1.3 cable. Some HDMI cables may not support Anynet+ functions. Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status. Anynet+ supports up to 12 AV devices in total. English - 62 BN68-01192F-02Eng-2.indd 62 2007-02-26 ソタネト 4:28:10 Setting Up Anynet+ The following settings are to use Anynet+ functions. To use the Anynet+ Function, Anynet+ (HDMI-CEC) must be set to On 1 2 3 Press the Anynet+ button. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ENTER button to select Anynet+ (HDMI-CEC), then press the ENTER button. Press the ▲ or ▼ button to select On, then press the ENTER button. The Anynet+ (HDMI-CEC) function is enabled. If you select Off, Anynet+ (HDMI-CEC) is disabled. When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related operations are deactivated. ➢ ➢ ➢ TV Air 28 Recevier: On Connect Recorder Setup Move Exit Enter Anynet+ Setup Anynet+ (HDMI-CEC) : OffOff Auto Turn Off : OffOn Searching Connections Move Enter Return Setting an Anynet+ Device to turn Off Automatically when the TV is Turned Off 2 Press the ▲ or ▼ button to select Auto Turn Off, then press the ENTER button. 3 Press the ▲ or ▼ button to select On, then press the ENTER button. ➢ The Auto turn off function is enabled. ➢ If you select Off, the Auto turn off function is canceled. Press the EXIT button to exit. ➢ ➢ Anynet+ Setup Anynet+ (HDMI-CEC) : On Auto Turn Off : Off Off Searching Connections Move On Enter Return The Select Device setting of the TV remote control is to be set to TV to use the Anynet+ function. If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned off. However, if the device is recording, it may not be turned off. Scanning and Switching between Anynet+ Devices 1 Press the Anynet+ button. Anynet+ devices connected with the TV are listed. ➢ 2 Press the ▲ or ▼ button to select to a particular device and press the ENTER button. It is switched to the selected device. 3 If you cannot find a device you want, press the ▲ or ▼ button to select Searching Connections, then press the ENTER button. The message Configuring Anynet+ connection... is displayed. When searching devices completes, the connected devices are listed in the Anynet+ menu. ➢ ➢ ➢ ➢ ➢ TV Air 28 On Recevier: Connect Recorder Setup Move Enter Exit Anynet+ Setup Anynet+ (HDMI-CEC) : On ► Auto Turn Off : On ► Searching Connections ► Switching to the selected devices may take up to 2 minutes. You cannot cancel the Enter Return Move operation during the switching operation. The time required to scan for devices is determined by the number of connected devices. When the device scan is complete, the number of found devices is not displayed. Although the TV automatically scans devices when it is turned on using the POWER button, devices connected when the TV is already on are not displayed in the device list. In this case, select the Searching Connections menu to search devices. If you have selected external AV device by pressing the SOURCE button, you cannot use the Anynet+ fu nction. Make sure to switch to an Anynet+ device by using the Anynet+ button. Continued... English - 63 BN68-01192F-02Eng-2.indd 63 2007-02-26 ソタネト 4:28:15 Anynet+ Menu The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV. Anynet+ Menu Description Switches from Anynet+ to TV broadcast mode. View TV Record Starts a recording. (This menu works only for a device supporting recording.) (Device_Name) Menu Shows the menu of the connected device. Example: When a DVD Recorder is connected, the DVD Recorder’s title menu appears. (Device_Name) Operation Shows the play control menu of the connected device. Example: When a DVD Recorder is connected, the play control menu of the DVD Recorder appears. Connect (Device_Name) Your TV connects to the corresponding device. Receiver Sound is output through the receiver (home theater). A audio stream in HDMI is one way only from Device to TV. But there’s SPDIF output in TV. So TV sound can be sent to HT. Setup You can set the Anynet+ (HDMI-CEC), auto turn off, and searching connections for using Anynet+. TV Remote Control Buttons Available in Anynet+ Mode Device Type Operating Status Available Buttons After switching to the device, when the menu of the corresponding device is displayed on the screen. Numeric buttons ▲/▼/◄/►/ENTER buttons Color buttons EXIT button After switching to the device, while playing a file ◄◄ (Backward search) ►►(Forward search) (Stop) ► (Play/Pause) Device with built-in Tuner After switching to the device, when you are watching a TV program CH ▲/▼ button Audio Device When Receiver is activated VOL +/- button MUTE button Anyview2 When watching TV ► (Play/Pause) Anynet+ Device ➢ ➢ ➢ ➢ ➢ ➢ ➢ The Anynet+ function only works when the remote control is set to TV. The REC button works only while in the recordable state. You cannot control Anynet+ devices using the buttons on the side of the TV. You can control Anynet+ devices only using the TV remote control. The TV remote control may not work under certain conditions. In this case, re-select the Anynet+ device. The Anynet+ functions don’t operate for the products from other manufacturers. The Anynet+ functions do not work withother manufacturers’ products. The ◄◄, ►► operations may differ depending on the device. Recording You can make a recording of a TV program using a recorder. Press the REC button. Recording begins. (Only when the Anynet+ enabled recording device is connected.) ➢ ➢ You can also record the source streams by selecting Record after pressing the Anynet+ button. ➢ Before recording, check whether the antenna jack is properly connected to the recording device. For the antenna connection to the recording device, refer to its user manual. The current TV program is recorded in the Watching TV status. If you are watching video from another device, the video from the device is recorded. English - 64 BN68-01192F-02Eng-2.indd 64 2007-02-26 ソタネト 4:28:16 Listening through a Receiver (Home theater) You can listen to sound through a receiver instead of the TV speaker. 1 Press the Anynet+ button. Press the ▲ or ▼ button to select Receiver, then press the ENTER button. TV Air 28 Recevier: On Connect Recorder 2 Press the ◄ or ► button to select to On, then press the ENTER button. Now you can listen to sound through the receiver. 3 Press the EXIT button to exit. ➢ When the receiver is set to On, you can listen to the TV sound through the 2-channel(Stereo) Move Enter Exit Sound. This is not always true. When TV is displaying DTV(air) TV can send out 5.1 channel sound through SPDIF. But when the source is DVD(for example), TV can receive only 2 channel sound using HDMI. In that case, 2 channel sound is only transmitted to the Receiver through SPDIF. If the receiver is exclusively for a home theater only (supporting audio only), it may not appear in the device list. Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work. In case of a content with copyright problem, listening through the receiver may not properly operate. When listening through the receiver, there are restrictions for using the PIP and audio-related menu. ➢ ➢ ➢ ➢ Setup Check Points before Requesting Service Symptom Anynet+ does not work. Solution Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only. ■ Connect only one receiver (home theater). ■ Check if the Anynet+ device power cord is properly connected. ■ Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections. ■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu. ■ Check whether the TV remote control is in TV mode. ■ Check whether it is Anynet+ exclusive remote control. ■ Anynet+ doesn’t work at a certain condition. (Searching channels) ■ When connecting or removing the HDMI 1.3 cable, please make sure to search devices again or restart your TV. ■ Check if the Anynet+ Function of Anynet+ device is set on. I want to start Anynet+. ■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu. ■ Press the TV button on the TV remote control to switch to TV. Then press the Anynet+ button to show the Anynet+ menu and select a menu you want. I want to exit Anynet+. ■ Select View TV in Anynet+ menu. ■ Press the SOURCE button on the TV remote control and select a device other than Anynet+ devices. ■ Press any of CH, CH LIST, PRE-CH, and FAV.CH to change to the TV mode. (Note that the channel button operates only when an Anynet+ device with a built-in tuner is not connected.) The Connecting to Anynet+ device... ■ You cannot use the remote control when you are configuring Anynet+ or switching to a message appears on the screen. view mode. ■ Use the remote control when the Anynet+ setting or switching to view mode is complete. The Anynet+ device does not play. You cannot use the play function when Plug & Play is in progress. The connected device is not ■ Check whether or not the device supports Anynet+ functions. displayed. ■ Check whether or not the HDMI 1.3 cable is properly connected. ■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu. ■ Search Anynet+ devices again. ■ You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables may not support Anynet+ functions. The TV program cannot be Check whether the antenna jack on the recording device is properly connected. recorded. The TV sound is not output through Connect the optical cable between TV and the receiver. the receiver. ■ English - 65 BN68-01192F-02Eng-2.indd 65 2007-02-26 ソタネト 4:28:16 Appendix Troubleshooting If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips apply, call your nearest Samsung service center. Problem Poor picture quality. Poor sound quality. No picture or sound. No sound or sound is too low at maximum volume. Picture rolls vertically. The TV operates erratically. The TV won’t turn on. Remote control malfunctions Digital broadcasting screen problem. Possible Solution Try another channel. Adjust the antenna. Check all wire connections. Try another channel. Adjust the antenna. Try another channel. Press the SOURCE button. Make sure the TV is plugged in. Check the antenna connections. Make sure the MUTE button is off. First, check the volume of units connected to your TV (digital broadcasting receiver, DVD, cable broadcasting receiver, VCR, etc.). Then, adjust the TV volume accordingly. Check all connections. Unplug the TV for 30 seconds, then try operating it again. Make sure the wall outlet is working. Replace the remote control batteries. Clean the upper edge of the remote control (transmission window). Check the battery terminals. Press the TV button to put your remote control in the TV mode. Make sure the remote has batteries. Check that the “+” and “-” ends of the batteries are inserted correctly. Please check the digital signal strength and input antenna. The image is too light or too dark. Adjust the Brightness and Contrast. Adjust the Fine tuning. The image is too large or too small. Adjust the Size settings. The visual qualities of digital channels The visual qualities of digital channels may vary depending on the original production method vary. (analog or digital). - If the original production method is digital: High visual quality. - If the original production method is analog: The digital program displayed on the screen is originally an analog program which has been converted to digital. The visual quality is of an SD(Standard Definition) grade. Screen is black and power indicator On your computer; check the Power and Signal Cable. light blinks steadily. The TV is using its power management system. Move the computer’s mouse or press any key on the keyboard. On your equipment check (STB, DVD, etc) ; Power and Signal Cable. The TV is using its power management system. Press the Source button on the panel or remote control. Turn the TV off and on. Although the TV caption shows HD, The HD(High Definition) caption that appears when switching channels or when pressing the the visual quality is not satisfactory. Information button on the remote control means the selected channel is a digital channel. If the broadcasting station converts an analog signal into digital and transmits the signal, the visual quality may not be perfect. English - 66 BN68-01192F-02Eng-2.indd 66 2007-02-26 ソタネト 4:28:16 Installing the Wall Mount Kit This installation is to be used when attaching the wall mount to a wall. When attaching to other building materials, please contact your nearest dealer. Wall Mount Kit Specifications ( VESA ) Product Family LCD-TV PDP-TV inch VESA Spec. (A * B) Standard Screw (C * D) Quantity 23 ~ 26 200 * 100 M4 * L10 4 32 ~ 40 200 * 200 M6 * L10 4 46 ~ 52 600 * 400 57 700 * 400 M8 * L15 4 42 ~ 50 600 * 400 63 No VESA M8 6 1 We provide the standard dimensions for wall mount kits as shown in the table above. 2 When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided. 3 Do not use screws longer than the standard dimension, as they may cause damage to the inside of the TV set. English - 67 BN68-01192F-02Eng-2.indd 67 2007-02-26 ソタネト 4:28:16 How to assemble the Stand-Base (depending on the model) Using the 6 screws for securing the stand base and the monitor, firmly attach the monitor to the stand base. (The exterior of the set may be different than the picture.) When mounting your TV on a wall, install the cover (1) on the stand-base using two screws. Warning Firmly secure the stand to the TV before moving it, as the stand may fall and could cause serious injury. ➢ Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen. Always store the TV upright. Specifications Model Name HP-T4254 HP-T5054 42 inch 50 inch PC Resolution 1024 x 768 @ 60 Hz 1360 x 768 @ 60 Hz Sound (Output) 10 W 15 W 41.5 X 4.1 X 27.5 inches (1059.5 X 757 X 316 mm) 41.5 X 13.4 X 30.5 inches (1231 X 848.5 X 316 mm) 67.6 lbs (30.7 kg) 73.8 lbs (33.5 kg) 91.4 lbs (41.5 kg) 97 lbs (44 kg) Screen Size (Diagonal) Dimension (W x H x D) Body With stand Weight Body With stand Environmental Considerations Operating Temperature Operating Humidity Storage Temperature Storage Humidity ➢ ➢ ➢ 50 °F to 104 °F (10 °C to 40 °C) 10% to 80%, non-condensing -4 °F to 113 °F (-20 °C to 45 °C) 5% to 95%, non-condensing This device is a Class B digital apparatus. Design and specifications are subject to change without prior notice. For the power supply, refer to the label attached to the product. Stand Swivel (Left / Right) HP-T4254/HP-T5054 Yes -20° ~ 20° English - 68 BN68-01192F-02Eng-2.indd 68 2007-02-26 ソタネト 4:28:19 Dimensions (HP-T4254) TOP VIEW FRONT VIEW JACK PANEL DETAIL 2 1/4"H x 18 3/4"W @ 5 3/4" UP FROM BOTTOM SIDE VIEW REAR VIEW English - 69 BN68-01192F-02Eng-2.indd 69 2007-02-26 ソタネト 4:28:53 Dimensions (HP-T5054) TOP VIEW FRONT VIEW JACK PANEL DETAIL 2 1/4"H x 18 3/4"W @ 5 3/4" UP FROM BOTTOM SIDE VIEW REAR VIEW English - 70 BN68-01192F-02Eng-2.indd 70 2007-02-26 ソタネト 4:30:17 This page is intentionally left blank. BN68-01192F-02Eng-2.indd 71 2007-02-26 ソタネト 4:31:34 HP-T4254 HP-T5054 MONITEUR À PLASMA Manuel du propriétaire Enregistrez vos produits Samsung en vous connectant sur : www.samsung.com/global/register Inscrivez ici le modèle et le numéro de série pour référence ultérieure. ▪ Modèle _______________ ▪ N° de série _______________ BN68-01192F-02Fre_1.indd 1 2007-02-26 ソタネト 5:49:16 Remarques importantes sur la garantie relative au format de l’image du téléviseur Le format écran large des écrans à plasma (16:9, soit le rapport hauteur/largeur de l’image) est conçu principalement pour les vidéos plein écran à écran large. Les images affichées sur ces écrans devraient être principalement du format d’écran large de rapport 16:9, ou élargies pour remplir l’écran si le modèle est doté de cette fonction et si les images bougent continuellement. Afficher des graphiques et images fixes à l’écran, comme les barres noires latérales des vidéo pour téléviseur de format standard et les émissions de ce format doivent se limiter à 5 % du temps d’écoute par semaine. En outre, l’affichage d’autres images et textes fixes, comme des rapports boursiers, des jeux vidéos, des logos des stations, des sites Web ou des graphismes et motifs informatiques doit être limité, comme il est indiqué ci-dessus pour tous les téléviseurs. Afficher des images fixes qui ne respectent pas les directives ci-dessus peut causer un vieillissement inégal des écrans à plasma en y créant des images rémanentes, subtiles mais permanentes. Pour éviter ce problème, varier les émissions et les images et regarder principalement des images en mouvement en plein écran, et non pas des motifs fixes ou des barres noires. Dans les modèles d’écran à plasma qui offrent des caractéristiques de format d’image, utiliser ces commandes pour obtenir différents formats en plein écran. Prendre garde au choix des formats et à leur durée d’utilisation. Le vieillissement inégal d’un écran à plasma causé par la sélection et l’utilisation d’un format et les images rémanentes ne sont pas couverts par la garantie limitée de Samsung. © 2007 Samsung Electronics Co., Ltd. All rights reserved. Français - 2 BN68-01192F-02Fre_1.indd 2 2007-02-26 ソタネト 5:49:16 Guide de l’utilisateur Image rémanente Un écran à plasma ne doit pas présenter une image fixe (comme celle des jeux vidéos) durant un laps de temps trop important, car elle peut causer une image rémanente. Ce phénomène est aussi appelé “brûlure d’écran” Pour éviter une telle image rémanente, la page 26 du présent guide explique comment diminuer la luminosité et le contraste de l’écran pour afficher une image fixe. Altitude L’écran à plasma ne fonctionne normalement qu’à une altitude inférieure à 6 500 pi. Chaleur à la partie supérieure de l’écran à plasma Le dessus de l’appareil peut devenir chaud après un fonctionnement prolongé alors que la chaleur se dissipe par les orifices de ventilation aménagés dans la partie supérieure de l’écran. Cet état est normal et n’est pas le signe d’une défectuosité du produit. Toutefois, il faut empêcher les enfants de toucher cette partie de l’écran. L’appareil laisse entendre un craquement. Un craquement peut se produire lorsque l’appareil se contracte ou se dilate à cause d’un changement au milieu ambiant, comme la température ou l’humidité. Cela est normal et n’est pas le signe d’une défectuosité. Défauts de cellules L’écran à plasma comporte de 1 230 000 (définition standard) à 3 150 000 (haute définition) pixels dont la création nécessite une technologie hautement perfectionnée. Toutefois, il peut y avoir quelques pixels lumineux ou sombres à l’écran. Ces pixels n’ont aucune incidence sur le rendement du produit. Éviter de faire fonctionner le téléviseur à une température inférieure à 5 °C (41 °F) Une image fixe affichée trop longtemps peut endommager l’écran à plasma de façon permanente. Le fait de regarder l’écran à plasma en format 4:3 durant une longue période peut laisser des traces de bordures apparaissant à gauche, à droite et au centre de l’écran causées par une différence d’émission de lumière à l’écran. Un DVD ou un jeu vidéo peut avoir le même effet sur l’écran. Les dommages ainsi provoqués ne sont pas couverts par la garantie. Image rémanente à l’écran. Les images fixes des jeux vidéo et des ordinateurs affichées durant une longue période peuvent causer des images rémanentes partielles. Pour éviter cet effet, réduire la luminosité et le contraste lorsque des images fixes doivent rester longtemps à l’écran. Garantie La garantie ne couvre pas les dommages causés par la rémanence. L’image rémanente n’est pas couverte par la garantie. Français - 3 BN68-01192F-02Fre_1.indd 3 2007-02-26 ソタネト 5:49:16 Table des matières RENSEIGNEMENTS GÉNÉRAUX ■ ■ ■ ■ ■ ■ RÉGLAGE DES CANAUX Liste des caractéristiques ......................................... 5 Accessoires .............................................................. 5 Affichage du panneau de configuration .................... 6 Affichage du panneau de branchement ................... 7 Télécommande......................................................... 8 Insertion des piles dans la télécommande ............... 9 BRANCHEMENTS ■ ■ ■ ■ ■ ■ ■ ■ ■ Branchement des antennes VHF et UHF ................. 9 Branchement du câble de télédistribution .............. 10 Branchement d’un magnétoscope.......................... 11 Branchement d’un caméscope ............................... 12 Branchement d’un lecteur DVD/récepteur.............. 12 Branchement d’un lecteur DVD/récepteur à la prise HDMI .. 13 Branchement d’un lecteur DVD/récepteur à la prise DVI ... 13 Branchement d’un système audio numérique ........ 14 Branchement d’un amplificateur ou d’un système de cinéma maison à DVD............................................ 14 ■ Branchement d’un ordinateur ................................. 14 Mise sous tension/hors tension du téléviseur......... 15 Fonction Prêt-à-l’emploi ......................................... 15 Changement de canal ............................................ 17 Réglage du volume ................................................ 18 Affichage des paramètres ...................................... 18 Affichage des menus .............................................. 18 Mémorisation des canaux ...................................... 19 Programmation de la télécommande ..................... 20 Pour choisir la source ............................................. 25 Pour entrer le nom de la source d’entrée ............... 25 RÉGLAGE DE L’IMAGE ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ÉCRAN D’ORDINATEUR ■ ■ ■ ■ Réglage automatique de l’image ............................ 26 Réduction numérique des bruits............................. 27 Modification du format de l’image........................... 28 Réglages d’image détaillés .................................... 29 Active Color (couleur active) .................................. 30 Technologie DNIe (Digital Natural Image engine) .. 30 Réglage du mode Cinéma...................................... 31 Réglage du mode écran bleu ................................. 31 Réglage du Nv nr HDMI ......................................... 31 Affichage de l’image sur image .............................. 32 Arrêt sur Image....................................................... 33 Réglage automatique du son ................................. 34 Réglages audio ...................................................... 34 Réglage de TruSurround XT .................................. 35 Sélection d’une piste de son multicanaux - numérique ... 35 Sélection d’une piste de son multicanaux - analogique .. 36 Contrôle automatique du volume ........................... 36 Sélection de la sourdine interne ............................. 36 Réglage du son Mélodie......................................... 37 Écoute du son provenant de la fenêtre secondaire (ISI) .. 37 Symboles Appuyer Utilisation du téléviseur comme écran d’ordinateur 43 Modes d’affichage .................................................. 43 Configuration du téléviseur par l’ordinateur............ 44 Réglage du PC cinéma maison ............................. 45 RÉGLAGE DE L’HORLOGE ■ Réglage de l’horloge .............................................. 46 ■ Sélection de la langue de menu ............................. 49 ■ Utilisation du mode Jeu (Game) ............................. 49 ■ Affichage des sous-titres codés (messages à l’écran) - numériques .......................................................... 50 ■ Affichage des sous-titres codés (messages à l’écran) - analogiques .......................................................... 51 ■ Niveau de transparence ......................................... 52 ■ Réglage de l’effet lumineux .................................... 52 ■ Fonction économiseur d’énergie ............................ 53 ■ Prévention de la brûlure d’écran ............................ 53 ■ Réduction des effets de la brûlure d’écran ............. 54 ■ Réglage des fonctions d’aide ................................. 54 ■ Ajustement fixation murale (vendue séparément) .. 55 ■ Mise à jour du logiciel ............................................. 56 ■ Fonction Puce V ..................................................... 56 À propos d’Anynet+ ■ ■ ■ ■ ■ ■ ■ PARAMÈTRES AUDIO ■ ■ ■ ■ ■ ■ ■ ■ ■ Sélection de l’antenne ............................................ 38 Ajout et suppression de canaux ............................. 38 Sélection des canaux favoris.................................. 39 Visualisation des listes de canaux .......................... 40 Réglage du mode de liste des canaux par défaut .. 40 Identification des canaux ........................................ 41 Syntonisation précise des canaux analogiques ..... 41 Contrôle de l’intensité du signal numérique ........... 42 Amplificateur à faible bruit (LNA)............................ 42 DESCRIPTION DES FONCTIONS FONCTIONNEMENT ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Bouton à une touche Qu’est-ce qu’Anynet+? ........................................... 62 Branchement d’appareils Anynet+ ......................... 62 Configuration d’Anynet+ ......................................... 63 Balayage et permutation entre les appareils Anynet+ .. 63 Enregistrement ....................................................... 64 Écoute par l’intermédiaire d’un récepteur............... 65 Liste de vérification avant de faire une demande de service .................................................................... 65 ANNEXE ■ ■ ■ ■ ■ ■ Identification des problèmes................................... 66 Comprend le jeu d’installation murale .................... 67 Comment assembler le support(selon le modèle) .. 68 Spécifications ......................................................... 68 Dimensions (HP-T4254) ......................................... 69 Dimensions (HP-T5054) ......................................... 70 ➢ Remarque Français - 4 BN68-01192F-02Fre_1.indd 4 2007-02-26 ソタネト 5:49:17 Renseignements généraux Liste des caractéristiques • • • • • Réglages vidéo pouvant être enregistrés dans la mémoire du téléviseur. Minuterie pour allumer et éteindre automatiquement le téléviseur. Minuterie spéciale de mise hors tension de l’appareil. Fonction de contrôle parental V-Chip. Excellents interface et réseautage numérique : Grâce au syntoniseur numérique HD intégré, les diffusions HD peuvent être visualisées sans récepteur. • Télécommande La télécommande peut être utilisée pour contrôler le téléviseur, ainsi que la plupart des lecteurs DVD, récepteurs, câblosélecteurs et magnétoscopes. • Excellente qualité d’image - La technologie DNIe offre des images d’une clarté s’approchant de la réalité. • SRS TruSurround XT - SRS TruSurround XT offre un système ambiophonique Dolby virtuel. Accessoires FAV .CH RET URN Veiller à ce que tous les articles suivants soient inclus avec le téléviseur. Si des articles sont manquants, contacter le détaillant. Télécommande(BN5900599A) / Piles AAA (4301-000103) Cordon d’alimentation (3903-000144) Guide de l’utilisateur/ Guide de configuration rapide Carte de garantie/ Carte d’enregistrement/ Guide de sécurité Couvre base/Vis (2ea) (Consulter la page 68) Tore de ferrite pour le câble d’alimentation (3301-001110) Tore de ferrite pour câble de prise AV latérale / S-VIDÉO (3301-001305) Tore de ferrite pour câble de prise Casque d’écoute (3301-001456) Linge de nettoyage Les pièces suivantes sont vendues séparément et sont disponibles dans la plupart des magasins d’électronique. Câble S-VIDÉO (BN39-00149A) Câble HDMI (BN39-00641A) Câble HDMI/DVI (BN39-00643A) Câbles pour composant (RCA) (BN39-00279A) Câble d’ordinateur (BN39-00115A) Câble audio d’ordinateur (BN39-00061B) Câble optique Câble d’antenne (BN39-00333A) ➢ Tore magnétique (cordon d’alimentation, câble audio/vidéo, câble S-Vidéo, casque d’écoute) Les tores de ferrite sont utilisés pour protéger les câbles contre les interférences. Lorsque vous branchez un câble, ouvrez le tore de ferrite et fixez-le sur le pourtour du câble au niveau de la fiche. Français - 5 BN68-01192F-02Fre_1.indd 5 2007-02-26 ソタネト 5:49:29 Affichage du panneau de configuration Touches dans la partie inférieure droite du panneau Touches de la partie inférieure droite du panneauLes touches du panneau inférieur droit permettent de commander les principales fonctions du téléviseur, y compris le menu à l’écran. Pour accéder aux fonctions plus avancées, utiliser la télécommande. ➢ La couleur et la forme de l’appareil peuvent varier selon le modèle. 1 SOURCE Alterner entre toutes les sources d’entrée accessibles (TV, AV1, AV2, S-Video1, S-Video2, Composant1, Composant2, PC, HDMI1, HDMI2, ou HDMI3). 2 MENU Afficher à l’écran le menu des fonctions du téléviseur. 3 + VOL – Augmenter ou diminuer le volume. Dans le menu à l’écran, utiliser les touches + VOL – de la même manière que les touches ◄ and ► de la télécommande. 4 CH Changer de canal. Dans le menu à l’écran, utiliser les touches CH de la même manière que les touches ▲ et ▼ de la télécommande. 5 (ENTER) Confirmer une sélection. 6 POWER Allumer et éteindre le téléviseur. Voyant d’alimentation Clignote et s’éteint lorsque le téléviseur est sous tension et s’allume en mode de mise en veille. Capteur de télécommande Pointer la télécommande vers ce capteur sur le téléviseur. 7 Speakers (Haut-parleurs) Français - 6 BN68-01192F-02Fre_1.indd 6 2007-02-26 ソタネト 5:49:43 Affichage du panneau de branchement Prises du panneau arrière Utiliser les prises du panneau arrière pour brancher des composants audiovisuels utilisés continuellement, par exemple un magnétoscope ou un lecteur DVD. Pour savoir comment brancher ce matériel, consulter les pages 9 à 14. La couleur et la forme de l’appareil peuvent varier selon le modèle. 1 ENTRÉE DE L’ALIMENTATION Brancher le cordon d’alimentation fourni avec le téléviseur. 2 DIGITAL AUDIO OUT (OPTICAL) Brancher à un composant audio numérique. 3 AUDIO OUT (R/L) Sorties audio pour appareils externes. 4 PC AUDIO IN Brancher à la prise de sortie audio d’un ordinateur. 5 PC IN Brancher à la prise de sortie vidéo d’un ordinateur. 6 DVI IN (HDMI 1) (AUDIO-R/L) Brancher à la prise de sortie audio DVI d’un appareil externe. 7 HDMI IN 1, 2 Brancher à la prise HDMI d’un appareil avec sortie HDMI. (Seul HDMI 1 prend en charge HDMI-DVI IN et PC). Cette entrée peut également servir de branchement DVI avec entrées audio analogiques distinctes. Un câble HDMI/DVI optionnel est nécessaire pour faire ce branchement. Lorsque l’adaptateur HDMI/DVI en option est utilisé, les entrées audio analogiques DVI du téléviseur permettent de recevoir le son des sorties gauche et droite de l’appareil DVI. (Non compatible avec un ordinateur) 8 ANT 1 IN(AIR)/ANT 2 IN(CABLE) Connecteur coaxial de 75 Ω pour l’antenne et le réseau câblé. 9 EX-LINK Brancher cette sortie à la prise sur le support mural en option. Cette fonction permet de régler l’angle de visionnement du téléviseur à l’aide de la télécommande. 0 AUDIO-R/L (AV IN 1) Entrées audio pour appareils externes, comme un caméscope ou un magnétoscope. ! S-VIDEO (AV IN 1) Entrée S-Vidéo pour appareils externes pourvus d’une sortie S-Vidéo, comme un caméscope ou un magnétoscope. @ VIDEO (AV IN 1) Entrée vidéo pour appareils externes, comme un caméscope ou un magnétoscope. # ENTRÉE COMPOSANT (COMPONENT) IN 1, 2 Entrées de composants vidéo (Y/PB/PR) et audio (R-AUDIO-L). Prises du panneau latéral Les prises du panneau latéral droit permettent de brancher un composant utilisé occasionnellement, comme un caméscope ou une console de jeu vidéo. La couleur et la forme de l’appareil peuvent varier selon le modèle. 1 ENTRÉE HDMI IN 3 Brancher à la prise HDMI d’un appareil avec sortie HDMI. ��������� 2 SERVICE Pour entretien seulement. 3 ENTRÉE S-VIDEO IN 2 Entrée S-vidéo pour appareils externes pourvus d’une sortie S-Vidéo. 4 ENTRÉE AV IN 2 Entrées vidéo et audio pour les appareils externes. 5 ÉCOUTEURS (HEADPHONE) Permet de brancher des écouteurs pour écouter une émission de télévision sans déranger les autres personnes qui se trouvent dans la pièce. Français - 7 BN68-01192F-02Fre_1.indd 7 2007-02-26 ソタネト 5:49:44 Télécommande La télécommande peut être utilisée jusqu’à une distance d’environ 7 mètres (23 pieds) du téléviseur. Toujours diriger la télécommande directement vers le téléviseur. Il est également possible d’utiliser la télécommande pour contrôler le téléviseur, le câblosélecteur, le lecteur DVD ou le récepteur. 1 POWER Permet d’allumer et d’éteindre le téléviseur. 2 TOUCHES NUMÉRIQUES Sélectionner directement un canal. 3 – Appuyer sur cette touche pour choisir des canaux supplémentaires (numériques et analogiques) diffusés par la même station. Par exemple, pour choisir le canal 54-3, appuyer sur 54, puis sur - et sur 3. 4 CH LIST Afficher la liste des canaux à l’écran. 5 ANTENNA Appuyer sur cette touche pour choisir “Air” ou “Câble”. 6 Fonctions magnétoscope/DVD - Rembobinage - Arrêt - Lecture/pause - Avance rapide 7 + VOL – Augmenter ou diminuer le volume. 8 MUTE Couper le son temporairement. 9 MENU Afficher le menu principal à l’écran. 0 S.MODE Sélectionner le mode sonore. ! RETURN Retourner au menu précédent. @ P.MODE Activer le mode image. RETURN # CAPTION Permet de commander la fonction de sous-titrage. FAV.CH $ FAV.CH Appuyer sur cette touche pour passer aux canaux favoris. % SLEEP Appuyer sur cette touche pour régler d’avance une durée au terme de laquelle le téléviseur s’éteindra automatiquement. ^ SRS ➢ ➢ Cette télécommande a été spécialement conçue pour les personnes ayant une déficience visuelle. Les touches POWER, Channel, Volume, STOP et LECTURE/ PAUSE comportent des points de braille. Un éclairage ambiant intense peut nuire à l’efficacité de la télécommande. ( Appuyer sur cette touche pour illuminer les touches VOL et CH et la touche source active (TV, DVD, CABLE, STB, VCR) de la télécommande. ) SOURCE Appuyer sur cette touche pour afficher toutes les sources vidéo accessibles. a PRE-CH Syntoniser le canal précédent. b WISELINK Non disponible. c REC Cette fonction peut être utilisée pour commander l’enregistrement sur les enregistreurs Samsung. (Consulter la page 64) CH Permet de changer le canal. e EXIT d Appuyer sur cette touche pour quitter le menu. f HAUT▲/BAS▼/GAUCHE◄/ DROITE►/ENTER Pour sélectionner des options de menu et modifier leur valeur. g INFO Appuyer sur cette touche pour afficher de l’information à l’écran. h Anynet+ Exécuter les fonctions Anynet+ et configurer les appareils Anynet+. i PAUSE Immobiliser l’image pendant une scène particulière. Appuyer de nouveau sur la touche pour reprendre la diffusion normale. j P.SIZE Pour changer de format d’affichage. k PIP Activation/désactivation de l’image sur image. l CH / Pour faire défiler les canaux disponibles. (Ces touches permettent de changer les canaux dans la fenêtre ISI seulement). Sélectionner le mode SRS TruSurround XT. m MTS Configurer la télécommande pour contrôler le téléviseur, magnétoscope, câblosélecteur, lecteur DVD ou le récepteur. n RESET & SET * TV/DVD/STB/CABLE/VCR Contrôler le téléviseur, le lecteur DVD, le récepteur, le câblosélecteur ou le magnétoscope. Pour sélectionner le son stéréo, mono ou SAP (Separate Audio Program). Lorsque la télécommande ne fonctionne pas, changer les piles et appuyer sur la touche RESET pendant 2 à 3 secondes avant de la réutiliser. Français - 8 BN68-01192F-02Fre_1.indd 8 2007-02-26 ソタネト 5:49:51 Insertion des piles dans la télécommande 1 2 3 ➢ Soulever le couvercle à l’arrière de la télécommande, comme illustré. Installer deux piles AAA. ➢ Veiller à faire correspondre les bornes + et – des piles avec le diagramme à l’intérieur du compartiment. ➢ Ne pas utiliser de piles de types différents, par exemple : une pile alcaline et une pile au manganèse. Fermer le couvercle, comme illustré. ➢ Si la télécommande ne doit pas être utilisée pour une longue période, retirer les piles et les ranger dans un endroit frais et sec. La télécommande a une portée d’environ 7 mètres (23 pieds). Les piles offrent une autonomie d’environ un an en usage normal. Si la télécommande ne fonctionne pas, vérifiez les points suivants : 1. Le téléviseur est-il sous tension? 2. Les bornes plus et moins des piles sont-elles inversées? 3. Les piles sont-elles déchargées? 4. Y a-t-il une interruption de courant? Le cordon d’alimentation est-il débranché? 5. Y a-t-il une source lumineuse fluorescente ou une enseigne au néon à proximité? Branchements Branchement des antennes VHF et UHF Si l’antenne est dotée de conducteurs semblables à ceux représentés ici, consulter à la rubrique “Antenne 300 Ω à deux conducteurs plats” ci-dessous. Si l’antenne est dotée d’un câble de branchement semblable à celui représenté ici, consulter la rubrique “Antenne 75 Ω à connecteur rond”. Si le téléviseur est pourvu de deux antennes, consulter la rubrique “Antennes VHF et UHF séparées”. Antenne 300 Ω à deux conducteurs plats Si une antenne conventionnelle (par exemple, une antenne de toit ou des “oreilles de lapin”) dotée de deux conducteurs plats de 300 Ω est utilisée, procéder comme suit : 1 Installer les fils des deux conducteurs sous les vis de l’adaptateur de 300-75 Ω (non fourni).Serrer les vis à l’aide d’un tournevis. 2 Brancher l’adaptateur dans l’entrée ANT 1 IN (AIR) ou ANT 2 IN (CABLE), à l’arrière du téléviseur. ANT 1 IN (AIR) Antennes à conducteur rond de 75 ohms 1 Brancher le conducteur de l’antenne dans l’entrée ANT 1 IN (AIR) ou ANT 2 IN (CABLE), à l’arrière du téléviseur. ANT 1 IN (AIR) Antennes VHF et UHF séparées Si le téléviseur est pourvu de deux antennes séparées (une antenne VHF et une antenne UHF), leurs signaux doivent être combinés avant de raccorder les antennes au téléviseur. Pour cette opération, un multiplexeur-adaptateur en option (en vente dans la plupart des boutiques d’électronique) est nécessaire. 1 Raccorder les conducteurs des deux antennes au combinateur. 2 Brancher le combinateur dans l’entrée (AIR) ou ANT 2 IN (CABLE), à l’arrière du téléviseur. UHF VHF UHF VHF ANT 1 IN (AIR) Français - 9 BN68-01192F-02Fre_1.indd 9 2007-02-26 ソタネト 5:49:55 Branchement du câble de télédistribution Pour raccorder un service de câblodistribution, procéder comme suit : Service de câblodistribution sans câblosélecteur 1 Brancher le câble dans la prise ANT 2 IN (CABLE) située à l’arrière du téléviseur. ➢ Ce téléviseur étant configuré pour le câble, il n’est pas nécessaire de posséder un câblosélecteur pour recevoir les canaux de câblodistribution diffusés en clair. ANT 2 IN (CABLE) Branchement d’un câblosélecteur de désembrouillage de tous les canaux 1 2 Repérer le câble raccordé à la sortie d’antenne ANT OUT du câblosélecteur. ➢ Cette prise peut porter la mention “ANT OUT”, “VHF OUT” ou simplement “OUT”. ANT IN ANT OUT Brancher l’autre extrémité du câble à l’entrée ANT 2 IN (CABLE) à l’arrière du téléviseur. ANT 2 IN (CABLE) Branchement d’un câblosélecteur de désembrouillage de certaines chaînes Si le câblosélecteur débrouille seulement certaines chaînes (par exemple les chaînes spécialisées), procéder comme suit : Un répartiteur à deux voies, un commutateur RF (A/B) et quatre câbles d’antenne sont nécessaires. (Ces articles sont offerts dans la plupart des boutiques d’électronique). 1 Repérer et débrancher le câble raccordé à l’entrée d’antenne ANT IN de le câblosélecteur. ➢ 2 ANT IN Cette prise peut porter l’inscription “ANT IN”, “VHF IN” ou simplement “IN”. Relier ce câble à un répartiteur à deux voies. En entrée câble Séparateur 3 Raccorder un câble d’antenne entre une sortie OUTPUT du répartiteur et l’entrée IN du câblosélecteur. En entrée câble Séparateur Câblosélecteur 4 Raccorder un câble d’antenne entre la sortie d’antenne ANT OUT du câblosélecteur et l’entrée B-IN du commutateur RF (A/B). En entrée câble Séparateur Câblosélecteur 5 Raccorder un autre câble entre l’autre sortie du séparateur et l’entrée A du commutateur RF (A/B). En entrée câble Séparateur Câblosélecteur 6 Raccorder le dernier câble d’antenne entre la sortie du commutateur RF (A/B) et l’entrée ANT 2 IN (CABLE) à l’arrière du téléviseur. RF (A/B) Interrupteur RF (A/B) Interrupteur Arrière du téléviseur En entrée câble Séparateur ANT 2 IN (CABLE) RF (A/B) Interrupteur Une fois les branchements effectués, régler le commutateur A/B à la position A pour un visionnement normal. Régler le commutateur A/B à la position B pour obtenir les canaux brouillés. (Lorsque la position B du commutateur A/B est sélectionnée, il faut également syntoniser la chaîne du signal de sortie du câblodistributeur, habituellement la chaîne 3 ou 4.) Français - 10 BN68-01192F-02Fre_1.indd 10 2007-02-26 ソタネト 5:49:58 Branchement d’un magnétoscope Branchement vidéo Ces instructions supposent que le téléviseur est déjà branché à une antenne ou à un système de câblodistribution (conformément aux instructions des pages 9 et 10). Ignorer l’étape 1 si le téléviseur n’est pas branché à une antenne ou un système de câblodistribution. 1 2 3 4 5 ➢ Débrancher le câble ou l’antenne à l’arrière du téléviseur. Brancher le câble ou l’antenne à l’entrée ANT IN à l’arrière du magnétoscope. Raccorder un câble d’antenne entre la sortie d’antenne ANT OUT du magnétoscope et l’entrée ANT 1 IN (AIR) ou ANT 2 IN (CABLE) du téléviseur. Raccorder un câble vidéo entre la sortie VIDEO OUT du magnétoscope et l’entrée AV IN 1 [VIDEO] du téléviseur. Raccorder les câbles audio entre les sorties AUDIO OUT du magnétoscope et les entrées AV IN 1 [R-AUDIO-L] du téléviseur. Si le magnétoscope est un modèle “mono” (non stéréo), relier les prises d’entrée audio droite et gauche du téléviseur au moyen d’un connecteur en Y (non fourni). Si le magnétoscope fonctionne en stéréo, deux câbles distincts doivent être branchés. Panneau arrière du téléviseur Panneau arrière du magnétoscope 5 Câble audio (non fourni) 2 4 Câble vidéo (non fourni) 3 Câble d’antenne (non fourni) ➢ ➢ Chaque magnétoscope possède une configuration de panneau arrière différente. Lors du branchement d’un magnétoscope, les couleurs du câble et de la borne de branchement doivent correspondre. Branchement S-Vidéo Le téléviseur Samsung peut être branché à la prise S-Vidéo d’un magnétoscope.(Ce raccordement offre une meilleure qualité d’image que celle offerte par le raccordement vidéo standard ci-dessus). 1 Pour commencer, suivre les étapes 1 à 3 de la section précédente pour brancher l’antenne ou le câble au magnétoscope et au téléviseur. 2 Raccorder un câble S-vidéo entre la sortie S-VIDEO OUT du magnétoscope et l’entrée AV IN 1 [S-VIDEO] du téléviseur. 3 Panneau arrière du téléviseur Panneau arrière du magnétoscope 3 Câble audio (non fourni) 2 Câble S-Vidéo (non fourni) Raccorder les câbles audio 3 Câble d’antenne (non fourni) entre les sorties AUDIO OUT du magnétoscope et les entrées AV IN 1 [R-AUDIO-L] Votre magnétoscope peut avoir une prise S-Vidéo. (Sinon, se procurer les câbles requis dans une boutique d’électronique.) du téléviseur. ➢ Chaque magnétoscope possède une configuration de panneau arrière différente. ➢ Lors du branchement d’un magnétoscope, les couleurs du câble et de la borne de branchement doivent correspondre. Français - 11 BN68-01192F-02Fre_1.indd 11 2007-02-26 ソタネト 5:50:04 Branchement d’un caméscope Les prises du panneau latéral du téléviseur simplifient le branchement d’un caméscope. Ils permettent de regarder directement les cassettes du caméscope, sans passer par un magnétoscope. 1 2 Raccorder un câble vidéo (ou S-Vidéo) entre la prise d’entrée vidéo AV IN 2 [VIDEO] (ou S-VIDEO) du téléviseur et la prise de sortie VIDEO OUT du caméscope. Raccorder les câbles audio entre les prises d’entrée AV IN 2 [L-AUDIO-R] du téléviseur et les prises de sortie AUDIO OUT du caméscope. Panneau latéral du téléviseur 1 Câble S-Vidéo (non fourni) ou Caméscope 1 Câble vidéo (non fourni) 2 CâbleAudio (non fourni) ➢ ➢ Chaque caméscope possède une configuration de panneau arrière différente. Lors du branchement d’un caméscope, les couleurs du câble et de la borne de branchement doivent correspondre. Branchement d’un lecteur DVD/récepteur Les prises du panneau latéral du téléviseur simplifient le branchement d’un lecteur de DVD ou d’un récepteur au téléviseur. 1 Brancher un câble de composant entre les prises d’entrée COMPONENT IN 1 [Y, PB, PR] (ou COMPONENT IN 2 [Y, PB, PR]) du téléviseur et les prises de sortie COMPONENT OUT [Y, PB, PR] du lecteur DVD ou du récepteur. 2 Brancher les câbles audio entre les prises d’entrée COMPONENT IN 1 [RAUDIO-L] (ou COMPONENT IN 2 [R-AUDIO-L]) du téléviseur et les prises de sortie AUDIO OUT du lecteur DVD ou du récepteur. Branchement d’un lecteur DVD/récepteur Panneau arrière du téléviseur 2 CâbleAudio (non fourni) 1 Câble de composant(non fourni) ➢ ➢ ➢ Le composant vidéo sépare le vidéo en Y (luminance (luminosité)), PB (bleu) and PR (rouge) pour une qualité d’image supérieure. S’assurer que les branchements audio et vidéo correspondent. Par exemple, si le câble vidéo est branché à la prise d’entrée COMPONENT IN, le câble audio doit être branché à la prise d’entrée COMPONENT IN. La configuration du panneau arrière de chaque lecteur DVD ou récepteur est différente. Lors du branchement d’un lecteur DVD ou d’un récepteur, les couleurs du câble et de la borne de raccordement doivent correspondre. Français - 12 BN68-01192F-02Fre_1.indd 12 2007-02-26 ソタネト 5:50:11 Branchement d’un lecteur DVD/récepteur à la prise HDMI Cette connexion assure la meilleure qualité d’image. 1 Brancher un câble HDMI entre la prise d’entrée HDMI IN 2 du téléviseur et la prise de sortie HDMI OUT du lecteur DVD ou du récepteur. Branchement d’un lecteur DVD/récepteur Panneau arrière du téléviseur 1 Câble HDMI(non fourni) Qu’est-ce que la HDMI? • HDMI, ou interface multimédia à haute définition, est une interface qui permet la transmission de signaux numériques audio et vidéo en utilisant un seul câble sans compression. • La différence entre les interfaces HDMI et DVI réside dans le fait que la HDMI est de plus petites dimensions, qu’elle est dotée du composant de codage HDCP (protection contre la copie numérique à large bande passante). ➢ La configuration du panneau arrière de chaque lecteur DVD ou récepteur est différente. ➢ Lors du branchement d’un lecteur DVD ou d’un récepteur, les couleurs du câble et de la borne de raccordement doivent correspondre. ➢ Lorsque le branchement est réalisé par la prise HDMI, il n’est pas nécessaire de brancher un câble audio. Les câbles audio ne sont nécessaires que dans le cas d’un branchement par la prise HDMI/DVI. Branchement d’un lecteur DVD/récepteur à la prise DVI Ce branchement n’est possible que si l’appareil externe est pourvu d’une prise de sortie DVI. 1 Brancher un câble de raccordement HDMI/DVI ou un adaptateur DVI-HDMI entre la prise [HDMI IN 1] du téléviseur et la prise DVI du lecteur DVD ou du récepteur. 2 Brancher les câbles audio entre la prise d’entrée DVI IN (HDMI 1) [R-AUDIO-L] du téléviseur et les prises de sortie AUDIO OUT du lecteur DVD ou du récepteur. Branchement d’un lecteur DVD/récepteur Panneau arrière du téléviseur 2 CâbleAudio (non fourni) 1 Câble HDMI/DVI(non fourni) ➢ ➢ ➢ La configuration du panneau arrière de chaque lecteur DVD ou récepteur est différente. Lors du branchement d’un lecteur DVD ou d’un récepteur, les couleurs du câble et de la borne de raccordement doivent correspondre. Seul l’entrée HDMI IN 1 prend en charge HDMI et l’entrée DVI IN. Français - 13 BN68-01192F-02Fre_1.indd 13 2007-02-26 ソタネト 5:50:16 Branchement d’un système audio numérique Les prises du panneau arrière du téléviseur permettent de brancher facilement un système audio numérique. 1 Brancher un câble optique entre les prises de sortie numérique optique DIGITAL AUDIO OUT (OPTICAL) du téléviseur et les prises d’entrée audionumérique du système audionumérique. Lorsqu’un système audionumérique est branché à la sortie “DIGITAL AUDIO OUT (OPTICAL)” : Baisser la sortie (volume) du téléviseur puis régler le volume à l’aide du système de contrôle de volume. Système audionumérique Panneau arrière du téléviseur Câble optique (non fourni) Que signifie OPTIQUE? • Un dispositif convertit le signal électrique en un signal lumineux optique et le transmet par un câble en fibres de verre. Un système transmet des signaux audionumériques sous forme d’onde lumineuse, le format S/PDIF, par le biais d’un conducteur en verre. ➢ La diffusion audio en 5.1 canaux est possible lorsque le téléviseur est raccordé à un appareil externe doté de cette fonction audio. ➢ Chaque appareil externe d’entrée possède une configuration de panneau arrière différente. ➢ Si un appareil externe (lecteur de DVD, récepteur ou câblosélecteur) est branché au téléviseur par l’intermédiaire de la prise HDMI, il n’y a pas de sortie audio par la prise optique. Branchement d’un amplificateur ou d’un système de cinéma maison à DVD 1 Brancher les câbles audio entre la prise de sortie AUDIO OUT [R-AUDIO-L] du téléviseur et la prise d’entrée AUDIO IN [L-AUDIO-R] de l’amplificateur ou du système de cinéma maison à DVD. Lorsqu’un amplificateur audio est branché aux sorties AUDIO OUT (AUDIO L/R) : Baisser la sortie (volume) du téléviseur puis régler le volume à l’aide du contrôle de volume de l’amplificateur. ➢ ➢ Panneau arrière du téléviseur Amplificateur ou d’un système de cinéma maison à DVD CâbleAudio (non fourni) Chaque amplificateur/système de cinéma maison à DVD possède une configuration de panneau arrière différente. Lors du branchement d’un amplificateur ou système de cinéma maison à DVD, les couleurs du câble et de la borne de branchement doivent correspondre. Branchement d’un ordinateur 1 2 Brancher un câble D-Sub entre la prise d’entrée PC IN [PC] du téléviseur et la prise de sortie PC de l’ordinateur. Panneau arrière du téléviseur PC Brancher un câble audio PC entre la prise d’entrée PC IN [AUDIO] du téléviseur et la prise de sortie audio de la carte son de l’ordinateur. 2 CâbleAudio (non fourni) 1 Câble D-Sub (non fourni) ➢ ➢ ➢ La configuration du panneau arrière de chaque ordinateur est différente. Lors du branchement d’un ordinateur, les couleurs du câble et de la borne de branchement doivent correspondre. La prise d’entrée HDMI IN 1 doit être utilisée pour un branchement de câble HDMI/DVI. Français - 14 BN68-01192F-02Fre_1.indd 14 2007-02-26 ソタネト 5:50:24 Fonctionnement Mise sous tension/hors tension du téléviseur Appuyer sur la touche POWER de la télécommande. Il est aussi possible d’utiliser la touche POWER du téléviseur. ➢ Le téléviseur peut prendre un certain temps avant de s’allumer. Fonction Prêt-à-l’emploi Au moment de la première mise en marche du téléviseur, les réglages de base s’effectuent automatiquement et subséquemment : 1 Appuyer sur la touche POWER de la télécommande. language, Shop Mode, Le message Configuration de la langue, des canaux et de l’heure (Menu i Menu Channels and Time will be set. language, Channels and Time will be set.) s’affiche. Start 2 Appuyer sur la touche ENTER pour choisir la langue. Appuyer sur la touche ▲ ou ▼ pour sélectionner la langue, suivie de la touche ENTER. Le message Sélectionner le mode Maison si ce téléviseur est installé à la maison (Select Home Mode when installing this TV at home.) s’affiche automatiquement. Prêt à l’emploi Select the language of the OSD. Menu Language Move 3 4 Appuyer sur la touche ◄ ou ► pour sélectionner Commerce (Shop) ou Maison (Home), suivie de la touche ENTER. ➢ La sélection par défaut est Maison (Home). ➢ Nous recommandons de régler le téléviseur sur le mode Maison pour une meilleure image à la maison. ➢ Le mode Commerce (Shop) n’est destiné qu’à une utilisation dans un environnement commercial. ➢ Pour retourner au mode Dynamique (Maison), dans l’éventualité où l’appareil se retrouve accidentellement en mode Commerce (Shop), appuyer sur la touche Volume et tenir enfoncé la touche MENU du panneau du téléviseur pendant cinq secondes. Appuyer sur la touche ▲ ou ▼ pour mémoriser les canaux du branchement sélectionné. Appuyer sur ENTER pour choisir Démarrer. ➢ Si l’antenne est branchée sur la prise d’entrée ANT 1 IN (AIR), sélectionner Air. Si elle est branchée sur la prise d’entrée ANT 2 IN (CABLE), sélectionner Câble. ➢ Si les prises ANT 2 IN (AIR) et ANT 1 IN (CABLE) sont toutes deux utilisées, sélectionner Air+Câble. ➢ En mode câble, il est possible de sélectionner la source de signal analogue appropriée (STD, HRC ou IRC) en appuyant sur la touche ▲ ou ▼, puis sur ENTER. Si le câble est numérique, sélectionner la source de signal pour une diffusion analogique et numérique. Pour connaître le système utilisé dans un secteur particulier, communiquer avec le câblodistributeur. Appuyer sur la touche ► pour choisir Démarrer, puis sur ENTER pour mémoriser les canaux. Pour connaître le système utilisé dans un secteur particulier, communiquer avec le câblodistributeur. :English Spanish Français Enter Skip Prêt à l’emploi Choisissesz le mode Maison lorsque vous installes ce téléviseur à la maison. Maison Magasin RETURN Dépl. Intro. Passer FAV.CH Prêt à l’emploi Choisir les antennes à mettre en mémoire. Démarrer Démarrer Démarrer Air Câble Air + Câble Dépl. Intro. Passer Prêt à l’emploi Choisit un type de signal de câble pour votre emplacement. Analogique STD Démarrer HRC IRC Numérique STD HRC IRC Dépl. Intro. Passer Suite... Français - 15 BN68-01192F-02Fre_1.indd 15 2007-02-26 ソタネト 5:50:34 5 Le téléviseur commence la mémorisation des canaux accessibles. Une fois la mémorisation de tous les canaux terminée, le menu Prog. auto (Auto program) réapparaît. Appuyer sur la ENTER lorsque les canaux ont été mémorisés. Le menu Mode Horloge s’affiche automatiquement. ➢ Pour arrêter la recherche avant la fin, appuyer sur la touche ENTER lorsque la fonction d’arrêt est sélectionnée. Prêt à l’emploi Progr. Aut. en cours Câble Chaîne 67 68% Arrêt Passer Intro. Prêt à l’emploi Progr.Aut. terminée. 14 Canaux déjà mémorisés. Air : 9 , Câble : 5. OK Passer Intro. 6 7 Appuyer sur la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Manuel pour régler l’heure manuellement, suivie de la touche ENTER. Entrer l’heure et la date actuelles s’affiche. ➢ Si Auto est sélectionné, Régler l’horloge à l’heure avancée s’affiche; passer à l’étape 9. Appuyer sur la touche ◄ ou ► pour passer à Mois, Jour, Année, Heure, Minute ou am/pm. Régler la date et l’heure en appuyant sur la touche ▲ or ▼, suivie de la touche MENU. ➢ Il est possible de régler directement le Mois, le Jour, l’Année, les Heure, et les Minute en appuyant sur les touches numériques de la télécommande. Prêt à l’emploi Choisir les mode horloge Mode horloge Intro. Dépl. Le message Profitez de votre écoute s’affiche. Appuyer sur la touche ENTER lorsque terminé. ➢ Même sans appuyer sur la touche ENTER, le message s’efface automatiquement au bout de quelques secondes. Passer Prêt à l’emploi Entrez la date et l’heure en cours. Mois Jour -- -- ---- Heure Minute am/pm -- -- -- Dépl. 8 : Manuel Auto i Année Intro. Réglage Passer Profitez de votre visionnage. OK Réglage automatique de l’horloge 9 Appuyer sur la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Activé ou Désactivé, suivie de la touche ENTER. Choisir le fuseau horaire de la région. le menu s’affiche automatiquement. Prêt à l’emploi Régler l’horloge á l’heure avancée. Heure avancée : 10 Appuyer sur la touche ▲ ou ▼ pour mettre le fuseau horaire en surbrillance (et pour mettre le fuseau horaire approprié en surbrillance sur la carte des ÉtatsUnis). Appuyer sur la touche ENTER. Si l’horloge ne se règle pas automatiquement, consulter la page 48. Dépl. On Off Intro. Passer Prêt à l’emploi Choisissez le fuseau horaire où vous vous trouvez. Newfoundland Atlantique Est Centre Rocheuses Pacifique Alaska Hawaii 11 Le message Profitez de votre écoute s’affiche. Appuyer sur la touche ENTER lorsque terminé. ➢ Même sans appuyer sur la touche ENTER, le message s’efface automatiquement au bout de quelques secondes. Dépl. Suite... i Intro. Passer Profitez de votre visionnage. OK Français - 16 BN68-01192F-02Fre_1.indd 16 2007-02-26 ソタネト 5:50:37 Pour réinitialiser ce paramètre… 1 2 Configuration TV Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur ENTER pour choisir Prêt-à-l’emploi. Pour en savoir plus sur la configuration des options, consulter les pages 15 et 16. ➢ La fonction Prêt-à-l’emploi n’est accessible qu’en mode TV et DTV. i ► ► ► ► ► ► ► : Français : Off : Moyen Intro. Retour La langue des menus, le mode Magasin, les canaux et l’heure sont réglés. Démarrer Changement de canal Utilisation des touches de canaux 1 Appuyer sur la touche CH ou CH pour changer de canal. Lorsque la touche CH ou CH est enfoncée, le téléviseur change de canal en séquence. Tous les canaux mémorisés par le téléviseur défilent à l’écran. (Le téléviseur doit avoir mémorisé au moins trois canaux.) Les canaux qui n’ont pas été mémorisés ou qui ont été supprimés de la mémoire ne seront pas affichés. Consulter la page 19 pour la mémorisation des canaux. ➢ Utilisation des touches numériques 1 À l’aide des touches numériques, entrer le numéro du canal à syntoniser. Par exemple, pour syntoniser la chaîne 27, appuyer sur 2, puis sur 7. Le téléviseur change la chaîne quand le second chiffre est enfoncé. RETURN FAV.CH Utilisation de la touche La touche “-” sert à choisir les stations émettrices de signaux numériques. 1 Par exemple, pour choisir le canal 7-1, appuyer sur 7, puis sur - et sur 1. ➢ Le code HD indique que le téléviseur est en mode réception réglé sur un signal DHD (haute définition numérique). Le code SD indique que le téléviseur est en mode réception réglé sur un signal de définition standard. ➢ Pour changer rapidement de canal, appuyer sur les touches numériques, suivies de la touche ENTER. Touche PRE-CH pour syntoniser le canal précédent Les touches numériques permettent d’accéder directement à n’importe quelle chaîne. 1 Appuyer sur la touche PRE-CH. Le dernier canal visionné est automatiquement sélectionné. ➢ Pour alterner rapidement entre deux canaux dont les positions sont éloignées, syntoniser l’un des deux canaux, puis utiliser les touches numériques pour syntoniser l’autre canal. Il suffit ensuite d’appuyer sur la touche PRE-CH pour passer de l’un à l’autre. RETURN FAV.CH RETURN FAV.CH Français - 17 BN68-01192F-02Fre_1.indd 17 RETURN 2007-02-26 ソタネト 5:50:40 Réglage du volume Utilisation des touches de réglage du volume 1 Appuyer sur VOL + or VOL – pour augmenter ou diminuer le volume. Utilisation de la touche de sourdine (Mute) En tout temps, le son peut être mis en sourdine à l’aide de la touche MUTE. 1 Appuyer sur la touche MUTE pour couper le son. L’indicateur Mute apparaît dans le coin inférieur gauche de l’écran. 2 Pour restaurer le son, appuyer de nouveau sur la touche MUTE ou sur la touche VOL + ou VOL –. RETURN FAV.CH RETURN Affichage des paramètres FAV.CH L’écran indique le canal actif et l’état de certains réglages audiovisuels 1 Appuyer sur la touche INFO de la télécommande. Le téléviseur affiche alors le canal, le type de configuration sonore et l’état de certains paramètres du son et de l’image. Appuyer sur la touche INFO une fois de plus ou attendre environ 10 secondes qu’il disparaisse automatiquement. Air 28 Mono Mode image : Dynamique Mode sonore : Personn. MTS : Stéréo 12 : 00 am RETURN FAV.CH Affichage des menus 1 Alors que le téléviseur est allumé, appuyer sur la touche MENU. Le menu principal apparaît à l’écran. Les cinq icônes de gauche représentent Image, Son, Canal, Configuration, Entrée. 2 Sélectionner une des cinq icônes à l’aide des touches ▲ et ▼. Ensuite, appuyer sur ENTER pour accéder au sous-menu de l’icône. 3 Appuyer sur la touche EXIT pour quitter le menu. ➢ Le menu à l’écran disparaît après environ une minute. TV Image Mode Contraste Luminosité Netteté Couleur Teinte V 50 ▼ : Dynamique ► 100 45 75 55 R 50 Plus Dépl. Intro. Sorite RETURN Français - 18 FAV.CH BN68-01192F-02Fre_1.indd 18 2007-02-26 ソタネト 5:50:45 Mémorisation des canaux Le téléviseur peut mémoriser tous les canaux captés par l’antenne (air) ou sur le câble. Une fois les chaînes mémorisées, les touches CH ou CH permettent de les parcourir successivement, ce qui évite de syntoniser chaque canal manuellement avec les touches numériques. La mémorisation des canaux s’effectue en trois étapes : sélection de la source de transmission, mémorisation automatique des canaux et ajout ou suppression manuelle de canaux. Sélection de la source de diffusion TV Chaîne Antenne : Air ► Pour que le téléviseur puisse mémoriser les canaux disponibles, il faut préciser la Prog. Auto ► source de signal à laquelle il est raccordé (air ou câble). Effacer les canaux brouillés ► 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Canal, suivie de la touche ENTER. 2 Appuyer sur ENTER pour choisir Antenne. Appuyer sur la touche ▲ ou ▼ pour sélectionner Air ou Câble, suivie de la touche ENTER. Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. TV Chaîne Air Antenne : Air Câble Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. Appuyer sur la touche EXIT pour quitter le menu. Mémorisation des chaînes (méthode automatique) 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Canal, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Prog. auto, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner le branchement d’antenne, suivie de la touche ENTER. ➢ Air : Signal d’antenne “Air”. Câble : signal d’antenne “Câble”. Air+Câble : Signaux d’antenne “Air” et “Câble”. ➢ Si l’antenne est branchée sur la prise d’entrée ANT 2 IN (CABLE), sélectionner Câble. Si elle est branchée sur la prise d’entrée ANT 1 IN (AIR), sélectionner Air. ➢ Si les deux options ANT 1 IN et ANT 2 IN sont raccordées, choisir Air + Câble. ➢ Si Air est choisi, passer à l’étape 5. 4 5 Appuyer sur les touches ▲ ou ▼ pour choisir la source du signal analogique appropriée (STD, HRC ou IRC), puis sur ENTER. Si le câble est numérique, sélectionner la source de signal pour une diffusion analogique et numérique. ➢ Si le câble est numérique, sélectionner la source de signal pour une diffusion analogique et numérique. ➢ STD, HRC et IRC désignent différents systèmes de câblodistribution. Pour connaître le système utilisé dans un secteur particulier, communiquer avec le câblodistributeur. La sélection de la source de signal est maintenant terminée. TV Retour Chaîne Antenne : Air Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. TV ► ► ► ► ► ► ► ► Retour Prog. Auto Choisir les antennes à mettre en mémoire. Air Démarrer Démarrer Démarrer Câble Air + Câble Dépl. TV Retour Intro. Prog. Auto Choisit un type de signal de câble pour votre emplacement. Analogique STD Démarrer HRC IRC Numérique STD HRC IRC Dépl. Intro. Retour Prog. Auto Prog. Aut. en cours Le téléviseur commence alors à mémoriser tous les canaux disponibles. Si vous voulez arrêter la programmation automatique, appuyez sur ENTER. le message Arrêter la programmation automatique? s’affiche. Sélectionner Oui en appuyant sur la touche ◄ ou ►. Appuyer sur la touche EXIT pour quitter le menu. ➢ Le téléviseur doit être branché à une antenne ou un câble pour pouvoir recevoir les signaux numériques. Même si un canal donné est supprimé de la mémoire, il est toujours possible de le syntoniser directement en composant son numéro sur la télécommande. ➢ • Tous les canaux de télévision numérique et analogique sont automatiquement mémorisés. • Il faut environ 3 à 10 minutes pour mémoriser les canaux. ► ► ► ► ► Retour Câble Chaîne 67 68 % Arrêt Retour Intro. Prog. Auto Arrêter la programmation automatique? 68 % Yes Dépl. No Intro. Retour Français - 19 BN68-01192F-02Fre_1.indd 19 2007-02-26 ソタネト 5:50:52 Programmation de la télécommande Une fois programmée correctement, la télécommande peut fonctionner selon cinq modes distincts : TV (téléviseur), VCR (magnétoscope), Câble et DVD. Appuyer sur la touche de la télécommande correspondant à l’appareil voulu pour commander cet appareil. ➢ La télécommande peut ne pas être compatible avec tous les lecteurs DVD, tous les magnétoscopes, tous les câblosélecteurs et tous les récepteurs TV numériques. Configuration de la télécommande pour faire fonctionner le magnétoscope 1 Éteindre le magnétoscope. 2 Appuyer sur la touche VCR de la télécommande du téléviseur. 3 Appuyer sur la touche SET de la télécommande du téléviseur. 4 Appuyer sur les touches numériques de la télécommande qui correspondent aux trois chiffres du code du magnétoscope dont les marques sont répertoriées à la page 22 du présent guide. Veiller à entrer tous les chiffres du code, même si le premier chiffre est “0”. (Si plusieurs codes sont indiqués, essayer d’abord le premier.) 5 Appuyer sur la touche POWER de la télécommande. Le magnétoscope devrait s’allumer si la télécommande est bien configurée. Si le magnétoscope ne s’allume pas après la configuration, répéter les étapes 2, 3 et 4, en essayant un autre code parmi ceux correspondant à la marque du magnétoscope. Si aucun autre code n’est répertorié, essayer tous les codes de magnétoscope, de 000 à 080. RETURN FAV.CH Remarque sur l’utilisation des . de la télécommande : Magnétoscope Quand la télécommande est dans le mode VCR, les touches de volume commandent toujours le volume du téléviseur. Configuration de la télécommande pour faire fonctionner le câblosélecteur 1 Éteindre le câblosélecteur. 2 Appuyer sur la touche CABLE de la télécommande du téléviseur. 3 Appuyer sur la touche SET de la télécommande du téléviseur. 4 Appuyer sur les touches numériques de la télécommande qui correspondent aux trois chiffres du code du câblosélecteur dont les marques sont répertoriées à la page 23 du présent guide. Veiller à entrer tous les chiffres du code, même si le premier chiffre est “0”. (Si plusieurs codes sont indiqués, essayer d’abord le premier.) 5 Appuyer sur la touche POWER de la télécommande. Le câblosélecteur devrait s’allumer si la télécommande est bien configurée. Si le câblosélecteur ne s’allume pas après que la configuration, répéter les étapes 2, 3 et 4 en essayant un autre code parmi ceux correspondant à la marque du câblosélecteur. Si aucun autre code n’est répertorié, essayer tous les codes, de 000 à 046. RETURN FAV.CH RETURN FAV.CH Remarque sur l’utilisation des modes de la télécommande : Câblosélecteur Quand la télécommande est dans le mode CABLE, les touches de volume commandent toujours le volume du téléviseur. Suite... RETURN Français - 20 FAV.CH BN68-01192F-02Fre_1.indd 20 2007-02-26 ソタネト 5:50:54 Configuration de la télécommande pour faire fonctionner le lecteur DVD 1 Éteindre le lecteur DVD. 2 Appuyer sur la touche DVD de la télécommande du téléviseur. 3 Appuyer sur la touche SET de la télécommande du téléviseur. 4 Appuyer sur les touches numériques de la télécommande qui correspondent aux trois chiffres du code du lecteur DVD dont les marques sont répertoriées à la page 24 du présent guide. Veiller à entrer tous les chiffres du code, même si le premier chiffre est “0”. (Si plusieurs codes sont indiqués, essayer d’abord le premier.) 5 Appuyer sur la touche POWER de la télécommande. Le lecteur DVD devrait s’allumer si la télécommande est bien configurée. Si le lecteur DVD ne s’allume pas après la configuration, répéter les étapes 2, 3 et 4 en essayant un autre code parmi ceux correspondant à la marque du lecteur DVD. Si aucun autre code n’est répertorié, essayer tous les codes, de 000 à 141. RETURN FAV.CH Remarque sur l’utilisation des modes de la télécommande : Lecteurs DVD Quand la télécommande est dans le mode DVD, les touches de volume commandent toujours le volume du téléviseur. Configuration de la télécommande pour contrôler le récepteur RETURN 1 Éteindre le récepteur. 2 Appuyer sur la touche STB de la télécommande du téléviseur. 3 Appuyer sur la touche SET de la télécommande du téléviseur. 4 Appuyer sur les touches numériques de la télécommande qui correspondent aux trois chiffres du code du récepteur dont les marques sont répertoriées à la page 23 du présent guide. Veiller à entrer tous les chiffres du code, même si le premier chiffre est “0”. (Si plusieurs codes sont indiqués, essayer d’abord le premier.) 5 Appuyer sur la touche POWER de la télécommande. Le récepteur devrait s’allumer si la télécommande est bien configurée. Si le récepteur ne s’allume pas après la configuration, répéter les étapes 2, 3 et 4 en essayant un autre code parmi ceux correspondant à la marque du récepteur. Si aucun autre code n’est répertorié, essayer tous les codes, de 000 à 074. FAV.CH RETURN FAV.CH Remarque sur l’utilisation des modes de la télécommande : STB Quand la télécommande est dans le mode STB, les touches de volume commandent toujours le volume du téléviseur. Suite... RETURN FAV.CH Français - 21 BN68-01192F-02Fre_1.indd 21 2007-02-26 ソタネト 5:50:58 Codes de programmation de la télécommande Magnétoscope Marque SAMSUNG ADMIRAL AIWA AKAI AUDIO DYNAMICS BELL&HOWELL BROKSONIC CANDLE CANON CITIZEN COLORTYME CRAIG CURTIS MATHES DAEWOO DB DIMENSIA DYNATECH ELECTROHOME EMERSON FISHER FUNAI GENERAL ELECTRIC GO VIDEO LG(Goldstar) HARMAN KARDON HITACHI INSTANT REPLAY JC PENNEY JCL KENWOOD KLH LIOYD LOGIK LXI JVC MAGNAVOX MARANTZ MARTA KONIA ORION MEI MEMOREX MGA MIDLAND MINOLTA Code 000 001 002 003 004 005 077 078 079 020 025 004 027 032 007 026 018 022 002 003 006 008 015 055 021 056 002 003 006 008 015 055 007 002 024 002 007 008 017 021 025 056 064 066 003 010 011 012 013 014 015 016 007 026 017 025 034 001 003 006 021 022 025 030 032 034 040 047 050 052 060 063 065 066 067 069 073 018 024 028 029 048 051 061 025 002 005 017 021 056 002 006 007 008 009 010 007 019 025 041 042 074 021 002 007 018 019 021 026 037 041 054 056 007 008 018 021 026 037 007 008 018 026 037 070 025 038 025 081 082 083 021 056 059 007 008 018 021 026 037 062 006 036 073 074 075 076 021 006 021 024 025 034 005 019 041 075 Marque MITSUBISHI MONTGOMERY WARD MTC MULTITECH NEC OPTIMUS PANASONIC PENTAX PENTEX RESEARCH+ PHILCO PHILIPS PIONEER PORTLAND PROSCAN QUARTZ QUASAR RADIO SHACK/ REALISTIC RCA SANSUI SANYO SCOTT SEARS SHARP SHIMTOM SIGNATURE SONY SYLVANIA SYMPHONIC TANDY TASHIKA TATUNG TEAC TECHNICS TEKNIKA TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH Code 019 034 041 046 020 002 025 002 005 025 038 007 008 018 026 037 062 064 020 021 056 071 072 019 041 075 008 021 056 059 021 080 019 026 039 053 015 049 055 017 018 021 056 006 018 020 021 024 025 029 034 048 056 002 017 019 021 035 041 043 057 068 076 026 018 024 003 047 052 067 006 018 019 024 028 029 041 048 051 020 034 045 015 027 033 038 058 025 027 033 044 021 025 056 059 025 018 025 006 037 025 037 068 021 006 021 025 031 066 003 019 029 051 052 002 006 002 007 026 026 007 026 002 002 003 006 019 020 021 024 025 034 038 041 007 008 018 026 037 023 027 033 Suite... Français - 22 BN68-01192F-02Fre_1.indd 22 2007-02-26 ソタネト 5:51:03 CÂBLOSÉLECTEUR Marque SAMSUNG GI HAMLIN HITACHI JERROLD MACOM MAGNAVOX OAK PANASONIC PHILIPS PIONEER RCA REGAL Code 000 001 002 003 004 005 006 007 041 003 024 031 025 030 038 039 025 030 019 023 028 026 003 022 027 037 044 019 021 023 028 004 018 020 044 014 022 040 003 Marque REGENCY SA SCIENTIFIC ATLAN SPRUCER STARGATE 2000 SYLVANIA TEXSCAN TOCOM UNIVERSAL VIEWSTAR WARNER AMEX ZENITH Code 015 023 042 043 042 043 022 036 016 016 032 033 034 019 021 023 028 046 017 029 035 037 045 RÉCEPTEUR SAMSUNG Produit Ground wave STB Satellite STB CABLE STB STB DVD COMBO Satellite STB HDD COMBO Standard Code 001 002 003 004 008 009 Produit Satellite STB HDD COMBO Premium CABLE STB HDD COMBO Standard CABLE STB HDD COMBO Premium Ground wave STB HDD COMBO Standard Ground wave STB HDD COMBO Premium Code 010 011 012 013 014 RÉCEPTEUR Marque ALPHASTAR ANAM CHANNEL MASTER CROSSDIGITAL CHAPARRAL DIRECT TV DAEWOO DISH NETWORK SYSTEM DISHPRO DRAKE DX ANTENNA ECHOSTAR EXPRESSVU GOI GE GENERAL INSTRUMENT HTS HOME CABLE HITACHI HUGHES NETWORK IQ IQ PRISM JANEIL JERROID JVC Code 023 043 018 034 019 035 015 016 017 019 022 045 060 061 062 065 066 067 068 074 069 070 069 018 024 032 027 025 069 070 071 069 069 065 046 047 048 063 064 069 056 022 015 017 020 020 059 063 069 070 Marque LG(Goldstar) MAGNAVOX MEMOREX MOTOROLA MACOM MITSUBISHI NEXT LEVEL PHILIPS PRIMESTAR PANASONIC PAYSAT PROSCAN RCA RADIOSHACK REALISTIC STS STAR TRAK SKY SKY LIFE SHACK STAR CHOICE SONY TOSHIBA ULTIMATE TV UNIDEN ZENITH Code 044 073 016 021 036 038 039 040 041 042 016 064 018 015 047 048 064 015 016 017 021 033 036 038 039 040 041 042 067 046 049 050 063 058 059 061 062 016 065 066 051 052 053 065 066 064 057 020 027 026 031 005 006 007 064 064 054 060 015 017 028 029 030 072 060 066 016 021 037 055 056 057 024 031 068 Suite... Français - 23 BN68-01192F-02Fre_1.indd 23 2007-02-26 ソタネト 5:51:03 DVD SAMSUNG Produit DVD DVDR BD Record VCR COMBO VCR Record DHR COMBO Code 000 001 002 003 004 005 006 007 008 009 010 011 012 013 Produit Home Theater VCR COMBO HDD Record COMBO TWIN TRAY COMBO STB DVD COMBO DVD Receiver AV Receiver Code 014 015 016 017 018 019 020 021 Lecteurs DVD Marque ANAM AUDIOVOX AUDIOLOGIC ANABA APEX DIGITAL AIWA BROKSONIC BLAUPUNKT B&K CURTIS MATHES CYBER HOME CLARION CIRRUS CINEVISION DAEWOO DENON FARENHEIT FISHER GPX GO VIDEO GE GREENHILL HITACHI HITEKER HOYO HARMAN / KARDON IRT INTEGRA JBL JVC JATON KENWOOD KISS KONKA KLH LG(Goldstar) LOEWE LASONIC MOBILE AUTHORITY MEMOREX MALATA MAGNAVOX MINTEK MONYKA Code 030 075 085 072 070 071 074 086 083 084 088 111 112 114 062 074 122 123 027 065 077 078 079 082 080 125 081 095 066 146 067 068 090 060 061 089 133 135 069 074 074 064 113 071 073 091 110 089 092 091 022 033 115 116 073 051 108 109 073 059 100 106 107 074 075 025 031 057 058 054 055 056 076 093 074 094 073 Marque NORCENT NEXT BASE NEC NANTAUS NESA OPTOMEDIA ELECTRONICS OPTIVIEW ONKYO PHILCO PRINCETON PROSCAN PANASONIC PHILIPS ROTEL RIO RCA RAITE ROWA SAMPO SONY SHERWOOD SVA SYLVANIA SHARP SANSUI SANYO SHINSONIC SANYO THOMSON TOSHIBA TECHNICS TVIEW TOKAI TEAC TECHWOOD TREDEX URBAN CONCEPTS VENTURER VOCOPRO YAMAHA YAMAKAWA XWAVE ZENITH Code 048 049 050 052 053 144 074 105 072 076 092 119 044 045 046 047 023 024 034 124 134 136 137 138 036 076 117 118 120 023 035 074 075 131 132 073 038 104 026 029 126 127 128 129 130 141 039 041 042 043 093 140 062 062 094 090 145 028 062 076 139 072 073 096 097 098 099 101 076 075 102 032 063 040 073 103 076 121 Français - 24 BN68-01192F-02Fre_1.indd 24 2007-02-26 ソタネト 5:51:03 Pour choisir la source Sélectionner le téléviseur ou une autre source d’entrée externe branchée au téléviseur, comme un lecteur DVD, un récepteur ou un câblosélecteur. Sélectionner pour choisir la source d’entrée désirée. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Entrée, suivie de la touche ENTER. Appuyer sur ENTER pour choisir Liste des sources. Appuyer sur la touche ▲ ou ▼ pour sélectionner la source du signal, suivie de la touche ENTER. ➢ Il est possible de choisir entre les jeux de prises suivants : AV1, AV2, S-Vidéo1, S-Vidéo2, Composant1, Composant2, PC, HDMI1 ou HDMI2 sur le panneau arrière du téléviseur et AV2, S-Vidéo2 ou HDMI3, sur le panneau latéral du téléviseur. ➢ L’entrée HDMI1, HDMI2 ou HDMI3 peut être sélectionnée uniquement lorsque l’appareil externe est sous tension et branché par l’intermédiaire de HDMI. ➢ Seuls les appareils externes branchés au téléviseur peuvent être sélectionnés. Entrée TV Liste source : TV Entrer le nom Anynet+ (HDMI-CEC) Dépl. TV ► ► Intro. Retour Liste source TV AV1 AV2 S-Vidéo1 S-Vidéo2 Composante1 Composante2 ▼ Plus Dépl. :---:---:---:---:---:---Intro. Retour Vous pouvez aussi appuyer sur la touche SOURCE de la télécommande pour sélectionner une source de signal externe. Pour entrer le nom de la source d’entrée Vous pouvez entrer le nom de l’appareil branché aux prises d’entrée afin de faciliter la sélection de la source d’entrée. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Entrée, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Entrer le nom, suivie de la touche ENTER. Entrée TV Liste source : TV Entrer le nom Anynet+ (HDMI-CEC) Dépl. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner la prise d’entrée AV1, AV2, S-Video1, S-Video2, Composant1, Composant2, PC, HDMI1, HDMI2 ou HDMI3, suivie de la touche ENTER. TV Appuyer sur la touche ▲ ou ▼ pour sélectionner la source d’entrée Magnétoscope, Lecteur DVD, D-Magnétoscope, Récepteur de câble, Récepteur HD, Récepteur satellite, Récepteur enregistreur numérique personnel, Récepteur audio vidéo, Récepteur DVD, Jeu, Caméscope, Combo DVD, PC, Récepteur VOD ou Téléviseur, suivie de la touche ENTER. AV1 AV2 S-Vidéo1 S-Vidéo2 Composante1 Composante2 ▼ Plus TV Retour :---:---:---:---:---:---- ► ► ► ► ► ► Retour Intro. Entrer le nom AV1 AV2 RETURN S-Vidéo1 S-Vidéo2 Composante1 Composante2 ▼ FAV.CH Plus Appuyer sur la touche EXIT pour quitter. Intro. Entrer le nom Dépl. 3 ► ► Dépl. TV ---: -Magnétoscope ----: -DVD --: -D-VHS - - -STB : -Câble - STB -: -HD Satellite : - - - - STB PVR STB ▼ Intro. Retour Entrer le nom ▲ AV1 AV2 S-Vidéo1 S-Vidéo2 Composante1 Composante2 ▼ Plus Dépl. Récepteur AV :Récepteur - - - - DVD ---:Jeu ---:Caméscope - - - -DVD :Combo ---:PC - - - - VOD :Décodeur TV Intro. Retour Français - 25 BN68-01192F-02Fre_1.indd 25 2007-02-26 ソタネト 5:51:07 Réglage de l’image Réglage automatique de l’image Le téléviseur est doté de trois modes d’image automatiques réglés en usine (Dynamique, Standard, Cinéma). Il est possible d’activer les réglages Dynamique, Standard, Cinéma à partir du menu. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Picture, suivie de la touche ENTER. TV Image Mode Contraste Luminosité Netteté Couleur Teinte V 50 ▼ : Dynamique Plus Dépl. TV 2 Mode Contraste Luminosité Netteté Couleur Teinte V 50 ▼ : Dynamique Dynamique Standard Cinéma Dépl. 100 45 75 55 R 50 Intro. Retour FAV.CH TV 3 Retour Plus RETURN Appuyer sur la touche P.MODE de la télécommande pour sélectionner l’un des réglages d’image standard . Intro. Image Appuyer sur ENTER pour choisir Mode. Appuyer sur la touche ▲ ou ▼ pour sélectionner le réglage d’image Dynamique, Standard ou Cinéma, suivie de la touche ENTER. • Choisir Dynamique pour augmenter la clarté et la netteté de l’image. • Choisir Standard pour le mode d’écoute générale. • Choisir Cinéma pour le visionnement de films. ► 100 45 75 55 R 50 Mode Mode Contraste Luminosité Netteté Couleur Teinte V 50 Appuyer sur la touche ▲ ou ▼ pour sélectionner Contraste, Luminosité, Précision, Couleur ou Teinte, suivie de la touche ENTER. ▼ : Dynamique 100 45 75 55 R 50 Plus Dépl. Intro. Retour Contraste 4 Appuyer sur la touche ◄ ou ► pour augmenter ou réduire la valeur d’un élément particulier. Appuyer sur la touche ENTER. ➢ • Teinte ne fonctionne pas en mode PC. • En mode PC, seuls Contraste et Luminosité peuvent être sélectionnés. • Chaque paramètre configuré est enregistrée séparément en fonction du mode d’entrée. • Lorsque des modifications sont apportées au Contraste, à la Luminosité, à la Précision, à la Couleur ou à la Teinte, la couleur affichée à l’écran est modifiée en conséquence. 100 Dépl. Réglage Retour Suite... Français - 26 BN68-01192F-02Fre_1.indd 26 2007-02-26 ソタネト 5:51:12 5 Appuyer sur la touche ENTER pour retourner à Image. 6 Appuyer sur la touche ▲ ou ▼ pour sélectionner Nuance de couleur, suivie de la touche ENTER. 7 Appuyer sur la touche ▲ ou ▼ pour sélectionner Froide2, Froide1, Normal, Chaude1 ou Chaude2, suivie de la touche ENTER. ➢ Lorsque le mode d’image est réglé à Dynamique ou Standard, Chaude1 et Chaude2 ne peuvent être sélectionnés. Rétablir les réglages de l’image sur les réglages par défaut 8 TV Image Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Couleur activée : On DNIe : On Régler : OK Dépl. Intro. ▲ TV ► ► ► ► ► ► ► Retour Image Plus Nuance coul. : Froide1 Froide2 Réglages des détails Froide1 Normal Format : 16:9 Chaude1 Réduct. bruit num. : Auto Chaude2 Couleur activée : On DNIe : On Régler : OK Dépl. Intro. ▲ TV Retour Image Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Couleur activée : On Effacer DNIe : On Régler : OK ▲ Appuyer sur la touche ▲ ou ▼ pour sélectionner Régler, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner OK, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ Tous les réglages de mode d’image peuvent être rétablis. Dépl. Intro. Retour Réduction numérique des bruits Si le signal de diffusion capté par le téléviseur est faible, il est possible d’activer la fonction de réduction numérique des bruits pour aider à éliminer les parasites et les images rémanentes qui apparaissent à l’écran. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Picture, suivie de la touche ENTER. TV Appuyer sur la touche ▲ ou ▼ pour sélectionner Réduct. bruit num., suivie de la touche ENTER. TV 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off, Basse, Moyen, Haute ou Auto, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ La fonction Réduct. bruit num. (Digital NR) est accessible dans tous les modes à l’exception du mode PC. Image Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Couleur activée : On DNIe : On Régler : OK Dépl. Intro. ▲ ► ► ► ► ► ► ► Retour Image ▲ Plus Nuance coul. : Froide1 Réglages des détails Off Format : 16:9 Basse Moyen Réduct. bruit num. : Auto Haute Couleur activée : On Auto DNIe : On Régler : OK Dépl. Intro. Retour Français - 27 BN68-01192F-02Fre_1.indd 27 2007-02-26 ソタネト 5:51:17 Modification du format de l’image La sélection du format de l’image dépend du type d’entrée vidéo. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Image, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Format, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner le format d’écran désiré. Appuyer sur la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. • 16:9 Règle l’image au mode écran large 16:9. • Zoom1 : Cette option permet d’agrandir le format de l’image. • Zoom2 : Agrandir le format d’image de l’option Zoom1. • Format large : Augmente le facteur de forme de l’image pour qu’elle remplisse l’ écran en entier. • 4:3 : Règle l’image au mode écran normal 4:3. • Numérisation seulement : Cette fonction permet d’afficher l’image complète non tronquée pour une entrée de signaux DTV ou HDMI 720p/1080i. TV Image Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Couleur activée : On DNIe : On Régler : OK Dépl. Intro. ▲ TV ► ► ► ► ► ► ► Retour Format 16:9 Zoom1 Position Régler Zoom2 Format large 4:3 Numérisation seulement ▲ ▼ Dépl. Intro. Retour RETURN FAV.CH ➢ 16:9 Règle l’image au mode écran large 16:9. Zoom 1 Format de l’écran lorsque l’écran large est agrandi verticalement. Zoom 2 Format de l’écran lorsque l’écran Zoom1 est agrandi verticalement. Format large Augmente le facteur de forme de l’image pour qu’elle remplisse l’écran en entier. 4:3 Règle l’image au format normal 4:3. Numérisation seulement Cette fonction permet d’afficher l’image complète non tronquée pour une entrée de signaux DTV ou HDMI 720p/1080i. • Tous les modes d’image sont accessibles en mode TV, VIDEO, S-VIDEO et COMPOSANT (480i, 480p). (16:9 ➞ Zoom1 ➞ Zoom2 ➞ 4:3) • En mode COMPOSANT (720p, 1080i) ou HDMI (720p, 1080i), il est possible de sélectionner les formats suivants : 16:9, 4:3 et Format large. • Dans les modes Zoom1, Zoom2 et Format large, l’image à l’écran à l’aide peut être déplacée à l’aide des touches ▲ ou ▼. • Il est impossible de modifier la taille de l’image lorsque le PIP (image sur image) est réglé à Double. • Lorsque le mode Double ( , ) est choisi pour PIP, la taille de l’image ne peut être configurée. • Le format large peut être utilisé lorsque le mode réception est réglé sur un signal HD (haute définition). Le format large règle l’image au format optimal en l’agrandissant horizontalement et verticalement. À titre d’exemple, il est possible de rétablir l’image de format 4:3 en format 16 :9. Le format Large ne prend pas tous les appareils externes en charge (DVD, magnétoscope, etc.). Français - 28 BN68-01192F-02Fre_1.indd 28 2007-02-26 ソタネト 5:51:23 Réglages d’image détaillés Il est possible de procéder au réglage détaillé de l’image. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Image, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Réglages détaillés, suivie de la touche ENTER. 3 Choisir l’option de réglages détaillés en appuyant sur la touche ▲ ou ▼, puis sur ENTER. 4 Une fois le réglage effectué correctement, appuyer sur la touche ENTER. TV TV Les Réglages détaillés ne peuvent être sélectionnés lorsque le mode de l’image est réglé à Dynamique. Dépl. Dépl. BN68-01192F-02Fre_1.indd 29 Intro. Retour Réglages des détails Réglage du noir : Off Off Contraste dynam. : Off Gamma : 0Basse Moyen Espace couleur : Large Équilibrage du blancÉlevé Commande couleur Amélioration des bords: Off Dépl. Intro. Retour Gamma 0 Réglage TV Retour Réglages des détails Réglage du noir : Off Contraste dynam. : Off Gamma :0 Espace couleur : Large Auto Équilibrage du blancLarge Commande couleur Amélioration des bords: Off Dépl. Intro. Retour Équilibrage du blanc Décal.-R Décal.-V Décal.-B Gain-R Gain-V Gain-B Régler Mon contrôle de couleur : Rose/Vert/Bleu/Blanc/Régler Ce réglage peut être ajusté pour répondre à des préférences particulières. Rose/Vert/Bleu/Blanc : Choisir la couleur voulue en appuyant sur la touche ▲ ou ▼, puis sur ENTER. Appuyer sur ◄ ou ► jusqu’à l’atteinte du réglage optimal. ➢ Pendant l’utilisation de la fonction Commande couleur, l’image affichée reste en mouvement. Régler : Les couleurs réglées précédemment seront rétablies selon les valeurs par défaut de l’appareil. 15 15 15 15 15 15 Dépl. Intro. Retour Commande couleur Rose Vert Bleu Blanc Régler 15 15 15 15 Dépl. TV Français - 29 Retour Réglages des détails TV Équilibrage du blanc : Décal.-R/Décal.-G/Décal.-G/Gain-R/Gain-G/Gain-B/Régler Il est possible de régler la température de la couleur pour obtenir une image de couleurs plus naturelles. Décal.-R/Décal.-G/Décal.-B/Gain-R/Gain-G/Gain-B : Une modification de la valeur des réglages entraîne un rafraîchissement de l’écran. Choisir l’option de réglage voulue en appuyant sur la touche ▲ ou ▼, puis sur ENTER. Appuyer sur ◄ ou ► jusqu’à l’atteinte du réglage optimal. Régler : L’équilibre des blancs précédemment établi sera rétabli selon les valeurs par défaut prédéfinies en usine. Amélioration des contours : Activé/Désactivé Il est possible de souligner le contour des objets. Intro. ► ► ► ► ► ► ► Réglage du noir : Off Off Basse Contraste dynam. : Off Gamma : 0Moyen Élevé Espace couleur : Large Équilibrage du blanc Commande couleur Amélioration des bords: Off Gamma : -3 ~ 3 Il est possible de régler la luminosité centrale des images. Appuyer sur ◄ ou ► jusqu’à l’atteinte du réglage optimal. Espace couleur: Auto/Large L’espace couleur est une matrice de couleurs comportant le rouge, le vert et le bleu. Sélectionnez votre espace couleur favori et vous pourrez apprécier un ton de couleur naturel. Il est possible de régler l’espace de reproduction de la couleur du signal d’entrée à Auto ou à Large. Réglages des détails TV Réglage du noir : Hors fonction/faible/moyen/élevé Il est possible de régler directement le niveau de noir de l’écran afin d’ajuster la profondeur de l’écran. Contraste dynamique : Hors fonction/faible/moyen/élevé Il est possible de régler le contraste de l’écran afin d’obtenir un contraste optimal. ► ► ► ► ► ► ► Retour Réglage du noir : Off Contraste dynam. : Off Gamma :0 Espace couleur : Large Équilibrage du blanc Commande couleur Amélioration des bords: Off Appuyer sur la touche EXIT pour quitter le menu. ➢ Image Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Couleur activée : On DNIe : On Régler : OK Dépl. Intro. ▲ Intro. Retour Réglages des détails Réglage du noir : Off Contraste dynam. : Off Gamma :0 Espace couleur : Large Équilibrage du blanc Commande couleur Amélioration des bords: Off Off On Dépl. Intro. Retour 2007-02-26 ソタネト 5:51:41 Active Color (couleur active) Lorsque cette option est activée, les couleurs du ciel et de l’herbe seront plus riches et plus claires, offrant ainsi une image plus vive à l’écran. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Image, suivie de la touche ENTER. TV Image Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Couleur activée : On DNIe : On Régler : OK Dépl. Intro. ▲ Appuyer sur la touche ▲ ou ▼ pour sélectionner Couleur active, suivie de la touche ENTER. TV 3 Appuyer sur la touche EXIT pour quitter le menu. ➢ ➢ Cette fonction n’est pas accessible en mode PC. Retour Image ▲ Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Couleur activée : On Off : On DNIe On Régler : OK Dépl. Intro. Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. ► ► ► ► ► ► ► Retour Lorsque Standard ou Cinéma est sélectionné en mode Image, la couleur active passe automatiquement à Off et se désactive. Lorsque le mode Image est réglé à Dynamique, la couleur active est activée, peu importe le réglage du mode Image. Technologie DNIe (Digital Natural Image engine) Ce téléviseur comprend la fonction DNIe qui permet d’avoir une qualité d’image de haut niveau. Si la DNIe est activée, il est possible de regarder l’écran alors que avec cette caractéristique est activée. Si la DNIe est en mode démo, il est possible de voir à l’écran la DNIe et les images en mode normal, à des fins de démonstration. Cette fonction permet de constater la différence dans la qualité de l’image. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Image, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner DNIe, suivie de la touche ENTER. ➢ Cette fonction est désactivée lorsque la source d’entrée est en mode PC. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off, DNIe ou On, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. • Off :Met le mode DNIe hors fonction. • DNIe : L’écran de droite présente l’image sans mode DNIe tandis que celui de gauche présente l’image avec mode DNIe en fonction. • On : Active le mode DNIe. ➢ TV Image Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Couleur activée : On DNIe : On Régler : OK Dépl. Intro. ▲ TV ► ► ► ► ► ► ► Retour Image Plus Nuance coul. : Froide1 Réglages des détails Format : 16:9 Réduct. bruit num. : Auto Off Couleur activée : On DNIe démo : On DNIe Régler : On ▲ Dépl. Intro. Retour La fonction DNIe n’est pas prise en charge par le mode Cinéma. Français - 30 BN68-01192F-02Fre_1.indd 30 2007-02-26 ソタネト 5:51:44 Réglage du mode Cinéma Détecte et traite automatiquement les signaux de film provenant de toutes les sources et règle l’image pour obtenir une définition maximale. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Mode Cinéma, suivie de la touche ENTER. TV Configuration Plus Protection grillage écran ► Nv nr HDMI : Normal ► Mode Film : Off ► Réglage du support mural ► ISI ► Function d’aide : On ► Mise à niveau du logiciel ► Dépl. Retour Intro. ▲ TV Configuration Plus Protection grillage écran Nv nr HDMI : Normal : Off Mode Film Off Réglage du support mural On ISI Function d’aide : On Mise à niveau du logiciel Dépl. Retour Intro. ▲ 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. Réglage du mode écran bleu Si le téléviseur ne reçoit aucun signal ou un signal très faible, un écran bleu remplace automatiquement l’image brouillée. Pour continuer à voir l’image de moindre qualité, le mode écran bleu doit être désactivé. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Écran bleu, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. TV Configuration Plus ► Écran Bleu : Off Mélodie : Basse ► PC ► PC cinéma maison : Off ► Effet lumière : Pen. ècoute ► Économiseur énergie : Off ► ▼ Plus Dépl. Retour Intro. ▲ TV Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ Appuyer sur la touche EXIT pour quitter le menu. ➢ L’écran bleu s’affiche lorsque le téléviseur ne reçoit aucun signal d’un appareil externe, quels que soient les paramètres choisis dans le mode Écran Bleu (Blue Screen). : Off Off : Basse On : Off : Pen. ècoute : Off Intro. Retour Réglage du Nv nr HDMI Utiliser cette fonction pour régler le niveau de noir de l’image en mode HDMI. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Nv nr HDMI, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Normal ou Basse, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ TV Configuration Plus Protection grillage écran ► Nv nr HDMI : Normal ► Mode Film : Off ► Réglage du support mural ► ISI ► Function d’aide : On ► Mise à niveau du logiciel ► Dépl. Retour Intro. ▲ TV Configuration Plus Protection grillage écran Nv nr HDMI : Normal Normal Mode Film : Off Basse Réglage du support mural ISI Function d’aide : On Mise à niveau du logiciel Dépl. Retour Intro. ▲ Cette fonction n’est activée que lorsque l’entrée externe est branchée à un HDMI (signaux RGB). Français - 31 BN68-01192F-02Fre_1.indd 31 2007-02-26 ソタネト 5:51:49 Affichage de l’image sur image Cet appareil est doté d’un syntoniseur intégré qui ne permet pas la fonction ISI (image sur image) dans le même mode.À titre d’exemple, il n’est pas possible de regarder un canal à l’écran principal et un différent canal dans la fenêtre ISI. Consulter la section “Paramètres ISI” ci-dessous pour les détails. Il est possible d’utiliser la fonction ISI pour regarder deux sources vidéo simultanément. (pour sélectionner le son de l’image ISI, consulter la page 37.) ➢ Quand la fonction V-Chip est activée, la fonction ISI ne peut être utilisée. (Voir la page 56.) Activation de l’image sur image 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner ISI, suivie de la touche ENTER. 2 Appuyer de nouveau sur la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner On, suivie de la touche ENTER. ➢ Si le téléviseur est éteint alors qu’il est en mode ISI, la fenêtre ISI ne s’afficher pas au rallumage. TV Configuration Plus Protection grillage écran ► Nv nr HDMI : Normal ► Mode Film : Off ► Réglage du support mural ► ISI ► Function d’aide : On ► Mise à niveau du logiciel ► Dépl. Retour Intro. ▲ TV ISI RETURN Appuyer sur la touche PIP de la télécommande pour activer ou désactiver l’ISI. . ➢ Off : Off : On : : DTV Air 3 - 0 ISI Format Position Chaîne Dépl. Intro. Retour FAV.CH Les signaux numériques peuvent être reçus sur l’écran ISI lorsque l’image provient d’une source externe (lecteur DVD, récepteur, ordinateur, etc.) branchée aux prises Composant 1 ou 2, PC ou aux prises HDMI 1, 2 ou 3 à l’écran principal. Redimensionnement de la fenêtre ISI 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Format, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner le format désiré pour la fenêtre ISI, suivie de la touche ENTER. ➢ Si l’image principale est en mode PC et HDMI 1, la fonction Format est bloquée. ➢ L’image de la fenêtre ISI peut sembler légèrement non naturelle lorsque l’écran principal est utilisé pour un jeu ou le karaoké. TV ISI ISI Format Position Chaîne : On : : : DTV Air 3 - 0 Dépl. Intro. Retour Suite... Français - 32 BN68-01192F-02Fre_2.indd 32 2007-02-26 ソタネト 5:56:53 Repositionnement de la fenêtre ISI 4 TV Appuyer sur la touche ▲ ou ▼ pour sélectionner Position, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour choisir la position désirée de la fenêtre ISI, suivie de la touche ENTER. ➢ Il n’est pas possible de sélectionner Position en modes Fenêtre double ( ) ). et Double largeur ( ➢ Si la fenêtre ISI est réglée à Fenêtre double ( ) ou Double largeur ), le format de l’écran ou l’alignement peut varier, selon le type de ( signal. Changement du canal ISI 5 Appuyer sur la touche ▲ ou ▼ pour sélectionner Canal, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ au bas de la télécommande pour sélectionner le canal désiré dans la fenêtre ISI, suivie de la touche ENTER. ➢ Le canal peut être actif lorsque l’image secondaire est réglée à TV. et CH : On : : : DTV Air 3 - 0 Dépl. TV Intro. Retour ISI ISI Format Position Chaîne : On : : : DTV Air 3▲- 0 DTV Air 3-0 ▲ RETURN Dépl. Intro. Retour FAV.CH Appuyer sur la touche EXIT pour quitter. Appuyer sur les touches PIP CH canal ISI. ISI ISI Format Position Chaîne de la télécommande pour changer de Arrêt sur Image 1 Appuyer sur la touche STILL de la télécommande pour faire un arrêt sur image. ➢ Le son normal se fait toujours entendre. Appuyer de nouveau sur cette touche pour annuler la fonction. ➢ Pour éviter toute brûlure d’écran, cette fonction est automatiquement annulée après cinq minutes. RETURN FAV.CH Français - 33 BN68-01192F-02Fre_2.indd 33 2007-02-26 ソタネト 5:56:55 Paramètres audio Réglage automatique du son Le téléviseur offre des réglages audio automatiques réglés en usine, soient Standard, Musique, Cinéma et Parole. Il est également possible de sélectionner Personn. pour rétablir les paramètres audio personnalisés. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur ENTER pour choisir Mode. Appuyer sur la touche ▲ ou ▼ pour sélectionner le réglage audio Standard, Musique, Cinéma, Parole ou Personn. suivie de la touche ENTER. TV Son Mode Égaliseur SRS TruSurround XT Options multi-pistes Volume auto Sourdine int. Sélect. son Régler Dépl. Appuyer sur la touche EXIT pour quitter le menu. : Personn. Standard Musique Cinéma : Off Parole Personn. : Off : Off : Principale Intro. Retour RETURN • Choisir Standard pour les paramètres par défaut standard. • Choisir Musique pour visionner des vidéoclips ou des spectacles. • Choisir Cinéma pour visionner des films. • Choisir Dialogue lorsqu’il s’agit d’une émission constituée principalement de dialogues (ex. : le bulletin de nouvelles). • Choisir Personn. pour rétablir les paramètres personnalisés (consulter Réglages audio). FAV.CH Réglages audio L’utilisateur peut ajuster les paramètres audio selon ses préférences personnelles. (Il est également possible d’utiliser un des réglages “automatiques”. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Égalisateur, suivie de la touche ENTER. 3 Appuyer sur ◄ ou ► pour choisir une fréquence particulière à ajuster. Appuyer sur la touche ▲ ou ▼ pour augmenter ou réduire le niveau de la fréquence particulière, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ • Réglage de l’équilibre du son G/D : Pour régler l’équilibre du son des haut-parleurs gauche et droit. • Réglage des fréquences (100Hz, 300Hz, 1KHz, 3KHz, 10KHz): Pour régler le niveau des fréquences de différentes bandes passantes. ➢ Si des réglages d’égalisateur, le mode audio passe automatiquement en mode personnalisé. Rétablir les réglages par défaut de l’égaliseur Pour utiliser la fonction Rétablir, le mode Jeu doit être activé. (Consulter la page 49) 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Régler, suivie de la touche ENTER. ➢ Les valeurs par défaut de l’égaliseur sont rétablies. Appuyer sur la touche EXIT pour quitter. TV Son Mode : Personn. ► Égaliseur ► SRS TruSurround XT : Off ► Options multi-pistes ► Volume auto : Off ► Sourdine int. : Off ► Sélect. son : Principale ► Régler Dépl. Intro. Retour TV Égaliseur R L Balance + + 0 0 - - 100Hz 300Hz 1KHz 3KHz 10KHz Dépl. TV Réglage Retour Son Mode : Personn. ► Égaliseur ► SRS TruSurround XT : Off ► Options multi-pistes ► Volume auto : Off ► Sourdine int. : Off ► Sélect. son : Principale ► Régler Retour Dépl. Intro. Français - 34 BN68-01192F-02Fre_2.indd 34 2007-02-26 ソタネト 5:56:59 Réglage de TruSurround XT TruSurround XT est une technologie SRS brevetée qui permet de reproduire les contenus multicanaux 5.1 par l’intermédiaire de deux haut-parleurs. Grâce à la technique TruSurround, le téléspectateur vit une expérience polyphonique totale, le son enveloppant étant diffusé par les deux enceintes de reproduction auxquelles s’ajoutent les haut-parleurs intégrés au téléviseur. Ce système est totalement compatible avec tous les formats multicanaux. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner SRS TruSurround XT, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. Son TV Mode Égaliseur SRS TruSurround XT Options multi-pistes Volume auto Sourdine int. RETURN Sélect. son Régler Dépl. : Personn. : Off Off On : Off : Off : Principale Intro. Retour FAV.CH Appuyer sur la touche EXIT pour quitter le menu. Appuyer sur la touche SRS de la télécommande pour sélectionner On ou Off. AVIS RELATIF AUX LICENCES ET AUX MARQUES DE COMMERCE TruSurround XT, SRS et Symbol sont des marques de commerce déposées de SRS Labs, Inc. La technologie TruSurround XT est intégrée sous licence de SRS Labs, Inc. Sélection d’une piste de son multicanaux - numérique Le système de transmission numérique du téléviseur assure la transmission simultanée de nombreuses pistes de son (par exemple, la traduction simultanée du programme en langues étrangères). Langue privilégiée 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Options multi-pistes, suivie de la touche ENTER. 3 Appuyer sur ENTER pour choisir Langue privilégiée. Appuyer sur la touche ▲ ou ▼ pour sélectionner la langue désirée (Anglais , Espagnol ou Français), suivie de la touche ENTER. TV Son Mode : Personn. ► Égaliseur ► SRS TruSurround XT : Off ► Options multi-pistes ► Volume auto : Off ► Sourdine int. : Off ► Sélect. son : Principale ► Régler Dépl. Retour Intro. TV Options multi-pistes Anglais Langue privilégiée : English Espagnol Son multi-piste : Stéréo Français ➢ Appuyer sur la touche EXIT pour quitter le menu. Seule une langue faisant partie des langues diffusées peut être sélectionnée. RETURN Appuyer sur la touche MTS de la télécommande pour écouter une autre langue que la langue préférée. FAV.CH Dépl. Intro. Retour Français - 35 BN68-01192F-02Fre_2.indd 35 2007-02-26 ソタネト 5:57:02 Sélection d’une piste de son multicanaux - analogique Selon l’émission diffusée, il est possible de procéder à une écoute en Mono, Stéréo ou SAP. Son multi-pistes 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Options multi-pistes, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Son multi-pistes, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner le paramètre désiré, suivie de la touche ENTER. TV Son Mode : Personn. ► Égaliseur ► SRS TruSurround XT : Off ► Options multi-pistes ► Volume auto : Off ► Sourdine int. : Off ► Sélect. son : Principale ► Régler Dépl. Retour Intro. TV Options multi-pistes Langue privilégiée : English Mono Son multi-piste : Stéréo Stéréo SAP Appuyer sur la touche EXIT pour quitter le menu. • Choisir Mono pour les canaux diffusés en monophonie ou si la réception du signal stéréo est mauvaise. • Choisir Stéréopour les chaînes diffusées en stéréophonie. • Choisir SAPpour écouter une émission diffusée en mode SAP (Separate Audio Program), habituellement un doublage en langue étrangère. RETURN Dépl. Intro. Retour FAV.CH Appuyer sur la touche MTS de la télécommande pour sélectionner Mono, Stéréo ou SAP. Contrôle automatique du volume Réduit la différence de niveau sonore entre les diffuseurs. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Volume auto, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. TV Son Mode : Personn. ► Égaliseur ► SRS TruSurround XT : Off ► Options multi-pistes ► Volume auto : Off ► Sourdine int. : Off ► Sélect. son : Principale ► Régler Dépl. Retour Intro. TV Son Mode Égaliseur SRS TruSurround XT Options multi-pistes Volume auto Sourdine int. Sélect. son Régler Dépl. Appuyer sur la touche EXIT pour quitter. : Personn. : Off : Off Off : Off On : Principale Intro. Retour Sélection de la sourdine interne Le son des haut-parleurs du téléviseur est coupé. Cette fonction s’avère utile lorsque les haut-parleurs de la chaîne audio sont utilisés en lieu de ceux du téléviseur. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Sourdine int., suivie de la touche ENTER. TV Son Mode : Personn. ► Égaliseur ► SRS TruSurround XT : Off ► Options multi-pistes ► Volume auto : Off ► Sourdine int. : Off ► Sélect. son : Principale ► Régler Dépl. Intro. Retour Suite... Français - 36 BN68-01192F-02Fre_2.indd 36 2007-02-26 ソタネト 5:57:05 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. TV Appuyer sur la touche EXIT pour quitter le menu. ➢ • Lorsque la sourdine interne est activée, les menus audio, à l’exception de l’option multi-pistes, ne peuvent pas être ajustés. • Les sorties audio gauche/droite et les sorties audionumériques (Optical) demeurent actives. • The VOL +, VOL - and MUTE ne fonctionnent pas lorsque la sourdine interne est activée. Haut-parleurs du téléviseur Son Mode Égaliseur SRS TruSurround XT Options multi-pistes Volume auto Sourdine int. Sélect. son Régler Dépl. : Personn. : Off Off : Off On : Off : Principale Intro. Retour Sortie audio optique (sortie G/D) vers la chaîne audio TV AV, S-Vidéo Composant, PC, HDMI TV AV, S-Vidéo Composant, PC, HDMI Sourdine int. Désactivée Sortie haut-parleurs Sortie haut-parleurs Sortie haut-parleurs Sortie du son Sortie du son Sortie du son Sourdine int. Activée Sourdine Sourdine Sourdine Sortie du son Sortie du son Sortie du son Aucun signal vidéo Sourdine Sourdine Sourdine Sourdine Mute Sourdine Lorsque la sourdine interne est activée, les menus audio, à l’exception de l’option multi-pistes, ne peuvent pas être ajustés. Réglage du son Mélodie La mélodie jouée par le téléviseur à la mise sous tension ou hors tension est configurable. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 TV Appuyer sur la touche ▲ ou ▼ pour sélectionner Mélodie, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off, Basse, Moyen ou Haute, suivie de la touche ENTER. Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ TV ► ► ► : Off ► : Pen. ècoute ► : Off ► : Off : Moyen Intro. Retour Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ Appuyer sur la touche EXIT pour quitter. AVIS RELATIF AUX LICENCES ET AUX MARQUES DE COMMERCE Fabriqué sous licence de Dolby Laboratories. Dolby et le symbole double D sont des marques de commerce de Dolby Laboratories. : Off Off Basse : Moyen Moyen Haute : Off : Pen. ècoute : Off Intro. Retour Écoute du son provenant de la fenêtre secondaire (ISI) Lorsque la fonction ISI est activée, il est possible d’écouter le son provenant de la fenêtre secondaire (ISI). 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Son, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Sélect. son, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Second., suivie de la touche ENTER. • Principale: Permet d’écouter le son de l’image principale. • Second.: Permet d’écouter le son de l’image secondaire. Cette potion peut être choisie lorsque l’ISI est activée. Son Mode : Personn. ► Égaliseur ► SRS TruSurround XT : Off ► Options multi-pistes ► Volume auto : Off ► Sourdine int. : Off ► Sélect. son : Principale ► Régler Retour Dépl. Intro. TV Appuyer sur la touche EXIT pour quitter le menu. ➢ TV Son Mode Égaliseur SRS TruSurround XT Options multi-pistes Volume auto Sourdine int. Sélect. son Régler Dépl. : Personn. : Off : Off Principale : Off Second. : Principale Intro. Retour Français - 37 BN68-01192F-02Fre_2.indd 37 2007-02-26 ソタネト 5:57:08 Réglage des canaux Sélection de l’antenne 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Chaîne, suivie de la touche ENTER. 2 Chaîne TV Air : Air Antenne Câble Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal : On LNA Dépl. Intro. Appuyer sur ENTER pour choisir Antenne. Appuyer sur la touche ▲ ou ▼ pour sélectionner Air ou Câble, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. Appuyer sur la touche ANTENNA de la télécommande pour sélectionner Air ou Câble. ➢ Si l’antenne est branchée à ANT1 IN(AIR), choisir Air. Si l’antenne est branchée à ANT2 IN(CABLE), choisir Câble. ➢ Si les entrées ANT1 IN(AIR) et ANT2 IN(CABLE) sont toutes deux branchées, choisir l’entrée d’antenne désirée. Si la source d’entrée de l’antenne n’est pas bien sélectionnée, des parasites peuvent apparaître à l’écran. Retour Ajout et suppression de canaux Il est possible d’ajouter ou de supprimer un canal pour afficher seulement les canaux désirés. Pour utiliser la fonction Liste des canaux, exécuter d’abord la fonction Progr. auto. (voir page 19). RETURN 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Chaîne, suivie de la touche ENTER. TV Chaîne Antenne : Air Prog. Auto FAV.CH Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal LNA : On Appuyer sur la touche ▲ ou ▼ pour sélectionner Liste des canaux, suivie de la touche ENTER. Dépl. TV 3 Intro. ► ► ► ► ► ► ► ► Retour Liste des canaux Tout Aiouté Favorite Mode liste par défaut: Tout Appuyer sur la touche ▲ ou ▼ pour sélectionner Ajouté, suivie de la touche ENTER. Dépl. Intro. ► ► ► ► Retour Liste des canaux /Aiouté DTV Air 2 4 Appuyer sur les touches ▲/▼/◄/► pour choisir le canal à ajouter, suivies de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Ajouter, suivie de la touche ENTER. Appuyer sur la touche MENU pour revenir en arrière. ➢ Tous les canaux ajoutés seront affichés dans le menu Ajouté. DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Dépl. Air 16 DTV Air 9-1 Air 10 Air 11 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 Mode liste Ajout. tout Intro. Page Supp. tout Retour Liste des canaux /Aiouté DTV Air 2 Suite... DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Regarder DTV Air 9-1 Ajouter Air 10 Supprimer Air 11 Favorite DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 Mode liste Dépl. Air 18 Intro. Ajout. tout Supp. tout Retour Français - 38 BN68-01192F-02Fre_2.indd 38 2007-02-26 ソタネト 5:57:11 5 Appuyer sur les touches ▲/▼/◄/► pour sélectionner le canal à supprimer, suivies de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Supprimer, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter. Liste des canaux /Aiouté DTV Air 2 Regarder DTV Air 9-1 Ajouter Air 10 Supprimer Air 11 Favorite DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Air 16 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 Supp. tout Mode liste Dépl. Page Intro. Retour • Touche rouge (P.MODE) : Appuyer plusieurs fois sur cette touche pour sélectionner Tout, Ajouté ou Favorite. • Touche verte (S.MODE) : Appuyer pour ajouter tous les canaux supprimés. • Touche jaune (STILL) : Appuyer pour supprimer tous les canaux en mémoire. Sélection des canaux favoris Il est possible de classer les canaux souvent regardés dans la liste de canaux favoris. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Chaîne, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour choisir Liste des canaux, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour choisir Tout ou Ajouté, suivie de la touche ENTER. 4 Appuyer sur les touches ▲/▼/◄/► pour sélectionner un canal en tant que canal favori, suivies de la touche ENTER. Appuyer sur les touches CH liste de canaux. 5 et CH TV Chaîne Antenne : Air Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. TV Liste des canaux Tout Aiouté Favorite Mode liste par défaut: Tout pour afficher la prochaine page de la Appuyer sur la touche ▲ ou ▼ pour sélectionner Favorite, suivie de la touche ENTER. Le symbole “ ” apparaît en surbrillance et le canal est enregistré comme canal favori. Pour supprimer une sélection de canal favori, appuyer sur la touche ENTER jusqu’à ce que le symbole “ ” disparaisse. Appuyer sur la touche EXIT pour quitter. ➢ Seuls les canaux déjà en mémoire peuvent faire partie des canaux favoris. ➢ Tous les canaux favoris sont affichés dans le menu Favorite. Pour accéder aux canaux classés dans la liste des canaux favoris, appuyer sur la touche FAV.CH de la télécommande. ► ► ► ► ► ► ► ► Retour Dépl. Intro. ► ► ► ► Retour Liste des canaux /Aiouté DTV Air 2 DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Air 16 DTV Air 9-1 Air 10 Air 11 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 Mode liste Dépl. Intro. Supp. tout Page Retour Liste des canaux /Aiouté DTV Air 2 DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Dépl. RegarderDTV Air 9-1 Ajouter Air 10 Supprimer FavoriteAir 11 Air 16 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 RETURN Mode liste Intro. Supp. tout Retour FAV.CH Français - 39 BN68-01192F-02Fre_2.indd 39 2007-02-26 ソタネト 5:57:17 Visualisation des listes de canaux Il est possible d’afficher une liste de tous les canaux, des canaux ajoutés ou des canaux préférés. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Chaîne, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Liste des canaux, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Tout, Ajouté ou Favorite, suivie de la touche ENTER. TV Chaîne Antenne : Air Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. TV Liste des canaux Tout Aiouté Favorite Mode liste par défaut: Tout Pour naviguer entre tous les canaux, les canaux ajoutés ou entre les canaux favoris, appuyer sur la touche rouge (P.MODE) de la télécommande. • Touche rouge (P.MODE) : Appuyer plusieurs fois sur cette touche pour sélectionner Tout, Ajouté ou Favorite. • Touche jaune (STILL) : Appuyer pour supprimer tous les canaux en mémoire. ► ► ► ► ► ► ► ► Retour Dépl. ► ► ► ► Retour Intro. Liste des canaux /Aiouté DTV Air 2 DTV Air 2 Air 3 Air 4 Air 5 Air 6 Air 7 DTV Air 7-1 Air 9 Dépl. Air 18 DTV Air 9-1 Air 10 Air 11 DTV Air 11-1 Air 12 Air 13 Air 14 Air 15 RETURN Mode liste Supp. tout Page Intro. Retour FAV.CH Réglage du mode de liste des canaux par défaut Il est possible de sélectionner Tout, Ajouté ou Favorite comme liste par défaut à afficher en appuyant sur la touche CH MGR. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Chaîne, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Liste des canaux, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Mode liste par défaut, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Tout, Ajouté ou Favorite, suivie de la touche ENTER. ➢ Sélectionnez la liste de canaux souhaitée lorsque vous appuyez sur la touche CH LIST. • Tout : Affiche tous les canaux lorsqu’on appuie sur la touche CH LIST de la télécommande. • Ajouté : Affiche tous les canaux ajoutés lorsqu’on appuie sur la touche CH LIST de la télécommande. • Favorite : Affiche les canaux favoris lorsqu’on appuie sur la touche CH LIST de la télécommande. Chaîne TV : Air Antenne Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal : On LNA Dépl. Intro. TV ► ► ► ► ► ► ► ► Retour Liste des canaux Tout Aiouté Favorite Tout Mode liste par défaut: Tout Aiouté Favorite Dépl. Intro. Retour Appuyer sur la touche EXIT pour quitter le menu. Appuyer sur la touche CH LIST de la télécommande pour afficher les listes de canaux. Français - 40 BN68-01192F-02Fre_2.indd 40 2007-02-26 ソタネト 5:57:21 Identification des canaux Les canaux peuvent être identifiés de sorte que leur indicatif d’appel s’affiche chaque fois que le canal est sélectionné. 1 Appuyer sur la touche MENU pour afficher le menu. TV Chaîne Appuyer sur la touche ▲ ou ▼ pour sélectionner Chaîne, suivie de la touche Antenne : Air Prog. Auto ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Nom, suivie de la Effacer les canaux brouillés touche ENTER. Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner le canal à renommer, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour choisir une lettre, un chiffre ou une espace (ce qui donne la séquence : A à Z, 0 à 9, +, -, *, /, espace). Appuyer sur la touche ► pour passer au champ suivant, qui est sélectionné. Choisir un deuxième caractère à l’aide de la touche ▲ ou ▼, comme ci-dessus. Répéter les étapes ci-dessus pour choisir les trois derniers caractères. Lorsque terminé, appuyer sur ENTER pour attribuer le nouveau nom. Pour effacer le nouveau nom assigné, choisir Effacer en appuyant sur la touche ◄ ou ►, puis sur ENTER. TV ► ► ► ► ► ► ► ► Retour Nom Effacer Effacer Effacer Effacer Effacer Air 6 Air 7 Air 9 Air 11 Air 13 ▼ Retour Intro. Dépl. TV Nom ▲ Air 6 Air 7 Air 9 Air 11 Air 13 Appuyer sur la touche EXIT pour quitter le menu. Le nom des canaux numériques est automatiquement assignés et ne peut donc pas être assignés par l’utilisateur. ➢ Effacer Effacer Effacer Effacer Effacer A ▼ ▼ Réglage Dépl. Retour Syntonisation précise des canaux analogiques La fonction de syntonisation précise permet d’optimiser manuellement la réception d’un canal. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Chaîne, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Syn. Précise, suivie de la touche ENTER. TV Chaîne Antenne : Air Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. ► ► ► ► ► ► ► ► Retour Syn. Précise 3 Appuyer sur ◄ ou ► pour ajuster la syntonisation précise. 4 Pour mémoriser les réglages de syntonisation précise, appuyer sur la touche ENTER. Pour réinitialiser la syntonisation, appuyer sur la touche ▼ pour choisir Rétablir, puis sur ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ Seuls les canaux numériques peuvent être syntonisés. ➢ Les noms des canaux syntonisés s’affichent accompagnés d’un “*”. Air 4 0 Régler Réglage Enregis Retour Syn. Précise Air 4 * Syn. Précision 10 Régler Réglage Enregis Retour Syn. Précise Air 4 0 Régler Dépl. Intro. Retour Français - 41 BN68-01192F-02Fre_2.indd 41 2007-02-26 ソタネト 5:57:25 Contrôle de l’intensité du signal numérique Contrairement aux canaux analogiques, dont la qualité de réception peut aller de “Réception embrouillée” à “Réception claire”. les canaux numériques (HDTV) ont une réception parfaite ou ne sont pas captés du tout. Par conséquent, contrairement aux canaux analogiques, il n’est pas possible de syntoniser un canal numérique avec précision. Cependant, il est possible d’ajuster l’antenne pour améliorer la réception des canaux numériques accessibles. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Canal, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Puissance signal, suivie de la touche ENTER. Si le capteur d’intensité du signal indique que le signal capté est faible, ajuster l’antenne pour améliorer sa puissance de réception. Poursuivre l’ajustement de l’antenne jusqu’à ce que l’obtention de la meilleure réception. TV Chaîne Antenne : Air Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. TV ► ► ► ► ► ► ► ► Retour Puissance signal Appuyer sur la touche EXIT pour quitter le menu. Il est également possible d’appuyer sur la touche ENTER pour sélectionner OK, suivie de la touche EXIT pour quitter le menu. OK Intro. Retour Amplificateur à faible bruit (LNA) Si le signal d’entrée est faible dans la zone où est situé le téléviseur, l’amplificateur à faible bruit peut amplifier ce signal et ainsi améliorer la réception. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Canal, suivie de la touche ENTER. TV Appuyer sur la touche ▲ ou ▼ pour sélectionner LNA, suivie de la touche ENTER. TV 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ LNA ne fonctionne que lorsque l’antenne est réglée à Air. (Consulter “Sélection de l’antenne” à la page 38.) ➢ Si l’image présente des parasites lorsque la fonction LNA est activée, la mettre à Off. ➢ Le paramètre LNA doit être configuré séparément pour chaque canal. Chaîne Antenne : Air Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Puissance signal LNA : On Dépl. Intro. ► ► ► ► ► ► ► ► Retour Chaîne Antenne : Air Prog. Auto Effacer les canaux brouillés Liste des canaux Nom Syn. Précise Off Puissance signal On LNA : On Dépl. Intro. Retour Français - 42 BN68-01192F-02Fre_2.indd 42 2007-02-26 ソタネト 5:57:26 Écran d’ordinateur Utilisation du téléviseur comme écran d’ordinateur Configuration du logiciel pour PC (Windows XP) Les paramètres d’affichage de Windows pour un PC standard sont indiqués ci-dessous. Toutefois, les écrans qui s’afficheront sur l’ordinateur pourraient être différents, selon la version de Windows et la carte vidéo installées. Cependant, même si l’affichage diffère, les paramètres de base s’appliquent dans la grande majorité des cas. (Sinon, communiquez avec le fabricant de l’ordinateur ou de la carte vidéo.) 1 Premièrement, cliquer sur Panneau de configuration dans le menu Démarrer de Windows. Lorsque la fenêtre du panneau de configuration s’afficher, cliquer sur Apparence et thèmes. La boîte de dialogue du même nom s’affiche. Cliquer sur Affichage pour afficher la boîte de dialogue du même nom. Cliquer sur l’onglet Paramètres de la boîte de dialogue Affichage. Réglage du format approprié (résolution) Réglage idéal : 1024 x 768 pixels. Si la boîte de dialogue comporte une option de fréquence de rafraîchissement verticale, la valeur appropriée est 60 ou 60 Hz. Sinon, cliquer sur OK et quitter la boîte de dialogue. 2 3 4 Modes d’affichage Si le signal en provenance du système équivaut au mode de signal standard, l’affichage s’ajuste automatiquement. Si le signal n’équivaut pas au mode de signal standard, consulter le manuel d’utilisation de la carte vidéo pour régler le mode. Sinon, il est possible qu’il n’y ait pas d’affichage vidéo. L’image à l’écran a été optimisée en usine pour les modes d’affichage ci-dessous. Entrée D-Sub Résolution 720 x 400 VGA SVGA XGA WXGA 640 x 480 800 x 600 1024 x 768 1360 x 768 Vertical Fréquence (Hz) Horizontal Fréquence (kHz) Vertical Polarité Polarité Polarité HP-T4254 HP-T5054 70.087 31.469 N P ✔ ✔ 59.940 31.469 N N ✔ ✔ 72.809 37.861 N N ✔ ✔ 75.000 37.500 N N ✔ ✔ 60.317 37.879 P P ✔ ✔ 72.188 48.077 P P ✔ ✔ 75.000 46.875 P P ✔ ✔ 60.004 48.363 N N ✔ ✔ 70.069 56.476 N N ✔ ✔ 75.029 60.023 P P ✔ ✔ 60.015 47.712 P P ✔ Entrée HDMI/DVI Résolution Vertical Fréquence (Hz) Horizontal Fréquence (kHz) Vertical Polarité Polarité Polarité HP-T4254 HP-T5054 720 x 400 70.087 31.469 N P ✔ ✔ 640 x 480 59.940 31.469 N N ✔ ✔ SVGA 800 x 600 60.317 37.879 P P ✔ ✔ XGA 1024 x 768 60.004 48.363 N N ✔ ✔ WXGA 1360 x 768 60.015 47.712 P P VGA • • • • ✔ Le mode entrelacé n’est pas pris en charge. Le téléviseur fonctionne anormalement si un format vidéo non standard est sélectionné. Le tableau ci-dessus est conforme aux règles IBM/VESA et se base sur l’utilisation de l’entrée analogique. “ ✔ ”signifie que ce mode est pris en charge. ➢ • Pour le HP-T4254, la qualité du texte PC est optimale en mode XGA (1 024 x 768 à 60 Hz). • Pour le HP-T5054, la qualité du texte PC est optimale en mode XGA (1360 x 768 à 60 Hz). (Trois pixels à gauche, à droite, en haut et en bas sont ombragés au paramètre de résolution 1 360 x 768 @ 60 Hz. Il ne s’agit pas d’un problème mécanique, mais d’une conséquence de la différence de pixels entre la résolution standard et l’écran à plasma.) • Si le téléviseur est utilisé comme écran d’ordinateur, la palette de couleurs 32 bits est prise en charge. • Selon le fabricant, l’écran d’ordinateur peut varier. et la version de Windows installée. Consulter le mode d’emploi de l’ordinateur concernant son branchement à un téléviseur. • S’il est possible de sélectionner des options de fréquence verticale et horizontale, sélectionner une fréquence verticale de 60 Hz et une fréquence horizontale de 48,4 kHz. • Dans certains cas, des signaux anormaux (comme des barres) peuvent apparaître à l’écran du téléviseur lorsque l’ordinateur est éteint (ou débranché). Si tel est le cas, appuyez sur la touche SOURCE de la télécommande ou du panneau du téléviseur pour passer en mode VIDÉO. Français - 43 BN68-01192F-02Fre_2.indd 43 2007-02-26 ソタネト 5:57:27 Configuration du téléviseur par l’ordinateur Utiliser la fonction de réglage automatique pour que le téléviseur règle automatiquement les signaux vidéo reçus de l’ordinateur. En outre, cette fonction syntonise automatiquement les réglages et ajuste les valeurs et les positions de la fréquence. Réglages automatiques 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner PC, suivie de la touche ENTER. TV Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ TV 2 Intro. Retour PC Verrouiller l’image Position Réglage Auto Rétablir l’image Appuyer sur la touche ▲ ou ▼ pour sélectionner Réglage auto (Auto Adjustment), suivie de la touche ENTER. Le message Réglage Auto en cours. Veuillez patienter. (Auto Adjustment in Progress. Please wait.) s’affiche et les réglages automatiques de l’image sont activés. Appuyer sur la touche EXIT pour quitter le menu. ➢ Cette fonction n’est pas accessible en mode DVI-Numérique. ➢ Passer d’abord en mode PC. ► ► ► : Off ► : Pen. ècoute ► : Off ► : Off : Moyen ► ► Dépl. Intro. Retour Auto Adjustment in progress. Please wait. Réglage de la qualité de l’écran La fonction de réglage de la qualité de l’image supprime ou réduit les parasites. Si le réglage de précision ne suffit pas à supprimer les parasites, régler la fréquence le mieux possible puis recommencer le réglage de précision. Une fois les parasites réduits, reprendre le réglage de l’image de façon à bien centrer celle-ci sur l’écran. ➢ Passer d’abord en mode PC. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner PC, suivie de la touche ENTER. 2 Appuyer sur ENTER pour choisir Verrouiller l’image. TV PC Verrouiller l’image Position Réglage Auto Rétablir l’image Dépl. TV 3 ► ► Intro. Verrouiller l’image Grain Affiné Appuyer sur la touche ▲ ou ▼ pour sélectionner Grain ou Affiné, suivie de la touche ENTER. Appuyer sur la touche ◄ ou ► pour régler la qualité de l’écran, suivie de la touche ENTER. 50 0 Dépl. Appuyer sur la touche EXIT pour quitter le menu. ➢ L’utilisation de cette fonction peut modifier la largeur de l’image. Au besoin, ajuster la position pour la centrer. Retour Intro. Retour Grain 50 Dépl. Réglage Retour Suite... Français - 44 BN68-01192F-02Fre_3.indd 44 2007-02-26 ソタネト 6:01:26 Repositionnement de l’image Après avoir branché le téléviseur à l’ordinateur, il est possible de régler la position de l’affichage, au besoin. ➢ Passer d’abord en mode PC. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner PC, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Position, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ or ▼ pour ajuster la position verticale de l’image. Appuyer sur la touche ▲ or ▼ pour ajuster la position horizontale de l’image. Appuyer sur la touche ENTER. TV PC Verrouiller l’image Position Réglage Auto Rétablir l’image Dépl. Intro. TV Réglage TV ➢ Passer d’abord en mode PC. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner PC, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Rétablir l’image, suivie de la touche ENTER. Le message Rétablissement de l’image terminé s’affiche. Retour Position Appuyer sur la touche EXIT pour quitter. Initialisation de la position de l’écran ► ► Intro. Retour PC Verrouiller l’image Position Réglage Auto Rétablir l’image Dépl. ► ► Intro. Retour Image Reset is completed. Appuyer sur la touche EXIT pour quitter le menu. ➢ Les réglages définis précédemment seront rétablis selon les valeurs par défaut prédéfinies en usine. Réglage du PC cinéma maison Cette fonction permet d’avoir des images de meilleure qualité en mode PC. Après avoir activé la fonction PC cinéma maison, vous pouvez ouvrir le menu réglages détaillés et effectuer des réglages sans que cela ne se répercute sur les réglages du mode TV. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Cinéma maison PC, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ TV Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ TV ► ► ► : Off ► : Pen. ècoute ► : Off ► : Off : Moyen Intro. Retour Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ Cette fonction n’est accessible qu’en mode PC. : Off : Moyen Off : Off On ècoute : Pen. : Off Intro. Retour Français - 45 BN68-01192F-02Fre_3.indd 45 2007-02-26 ソタネト 6:01:28 Réglage de l’horloge Réglage de l’horloge Pour pouvoir utiliser les différentes fonctions de minuterie du téléviseur, il faut d’abord régler l’horloge. Cette fonction permet de vérifier l’heure pendant l’écoute du téléviseur. (Il suffit d’appuyer sur la touche INFO). Option 1 : Réglage manuel de l’horloge 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Heure, suivie de la touche ENTER. TV 2 Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur ENTER pour choisir Horloge. TV ► ► ► ► ► ► ► : Français : Off : Moyen Retour Intro. Heure --/ --/ ----/ -- : -- -- 3 Appuyer sur ENTER pour choisir Horloge. Appuyer sur la touche ▲ ou ▼ pour sélectionner Manuel, suivie de la touche ENTER. Horloge Mise en veille Minuterie1 Minuterie2 Minuterie3 Dépl. Intro. TV 4 : Auto Manuel Auto : Off Dépl. TV 5 Appuyer sur la touche ◄ ou ► pour passer à Mois, Jour, Année, Heure, Minute ou am/pm. Régler la date et l’heure en appuyant sur la touche ▲ or ▼, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ L’heure s’affiche chaque fois que la touche INFO est enfoncée. ➢ Il est possible de régler directement le Mois, le appuyant, l’Année, les Heure, et les Minute en appuyant sur les touches numériques de la télécommande. Retour Horloge Mode horloge Rég. horloge Fuseau hor. H. d’ été Appuyer sur la touche ▲ ou ▼ pour sélectionner Rég. horloge, suivie de la touche ENTER. ► ► ► ► ► : Off : Désactivé : Désactivé : Désactivé Intro. Retour Horloge Mode horloge Rég. horloge Fuseau hor. H. d’ été : Manuel Dépl. Intro. TV ► ► ► ► : Off Retour Rég. horloge Entrez la date et l’heure en cours. Mois Jour -- -- ---- Heure Minute am/pm -- -- -- Dépl. Année Réglage Retour Suite... Français - 46 BN68-01192F-02Fre_3.indd 46 2007-02-26 ソタネト 6:01:29 Option 2 : Réglage automatique de l’horloge L’horloge peut être réglée automatiquement si le téléviseur reçoit un signal numérique. 1 TV Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Heure, suivie de la touche ENTER. TV ► ► ► ► ► ► ► : Français : Off : Moyen Intro. Retour Heure --/ --/ ----/ -- : -- -- 2 Horloge Mise en veille Minuterie1 Minuterie2 Minuterie3 Appuyer sur ENTER pour choisir Horloge. Dépl. TV 3 Dépl. TV 4 Appuyer sur la touche ▲ ou ▼ pour sélectionner Fuseau hor., suivie de la touche ENTER. 5 Appuyer sur la touche ▲ ou ▼ pour mettre en surbrillance le fuseau horaire de la région (et pour mettre en surbrillance le fuseau horaire approprié sur la carte). Ensuite, appuyer sur ENTER. 6 Appuyer sur la touche ▲ ou ▼ pour sélectionner H. d’été, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Activé ou Désactivé, suivie de la touche ENTER. Intro. Retour Horloge Mode horloge Rég. horloge Fuseau hor. H. d’ été Appuyer sur ENTER pour choisir Horloge. Appuyer sur la touche ▲ ou ▼ pour sélectionner Auto, suivie de la touche ENTER. ► ► ► ► ► : Off : Désactivé : Désactivé : Désactivé : Auto Manuel Auto : Off Intro. Retour Fuseau hor. Choisissez le fuseau horaire où vous vous trouvez. Newfoundland Atlantique Est Centre Rocheuses Pacifique Alaska Hawaii Dépl. TV Intro. Retour Horloge Mode horloge Rég. horloge Fuseau hor. H. d’ été Dépl. : Auto : Off On Off Intro. Retour Appuyer sur la touche EXIT pour quitter le menu. En fonction de la station émettrice et du signal, il est possible que la fonction de réglage automatique de l’horloge ne fonctionne pas correctement. Dans un tel cas, régler l’horloge manuellement. ➢ L’antenne ou le câble doit être branché pour que le réglage automatique de l’horloge s’effectue. ➢ Suite... Français - 47 BN68-01192F-02Fre_3.indd 47 2007-02-26 ソタネト 6:01:31 Réglage de la minuterie activée/désactivée Cette fonction permet d’allumer ou d’éteindre le téléviseur à l’heure voulue. Tout d’abord, il faut régler l’horloge. 1 2 3 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Heure, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Minuterie1, Minuterie2 ou Minuterie3, suivie de la touche ENTER. Le menu Minuterie s’affiche. Appuyer sur la touche ▲ ou ▼ pour régler l’heure, suivie de la touche ► pour passer à la prochaine étape. Régler les autres options en procédant de la même manière. Appuyer sur la touche ◄ ou ► pour sélectionner l’élément désiré ci-dessous. Appuyer sur la touche ▲ ou ▼ pour ajuster le réglage. TV Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. TV : Off : Moyen Retour Intro. Heure 1/ 1/ 2007/ 12 : 04 am Horloge Mise en veille Minuterie1 Minuterie2 Minuterie3 ► ► ► ► ► : Off : Désactivé : Désactivé : Désactivé Dépl. Appuyer sur la touche EXIT pour quitter le menu. Retour Intro. Minuterie 1 • Heure d’activation : Sélectionner l’heure, les minutes, am/pm et Désactivé/Activé. (Pour activer la mise en veille, sélectionner Activé). • Heure de désactivation :Sélectionner l’heure, les minutes, am/pm et Désactivé/ Activé. (Pour activer l’heure d’arrêt, sélectionner Activé). • Répéter : Sélectionner Une fois, Tous les jours, Lundi au vendredi, Lundi au samedi ou Samedi et dimanche. • Volume :Sélectionner le niveau sonore auquel vous voulez régler le téléviseur au moment de la mise sous tension à l’aide la minuterie. • Contenu : Quand la minuterie ON est activée, il est possible de syntoniser un canal particulier ou lire d’autre type de contenu, comme des photographies ou des fichiers sonores. (Veiller à ce qu’un dispositif USB soit branché au téléviseur.) ➢ Il est possible de régler directement les heures et les minutes en appuyant sur les touches numériques de la télécommande. ➢ ► ► ► ► ► ► ► : Français Arrêt automatique Lorsque la minuterie est activée, le téléviseur s’éteint si aucune commande n’est activée dans les trois heures qui suivent la mise sous tension du téléviseur par la minuterie. Cette fonction est seulement disponible en mode Minuterie activée et évite toute fuite ou surchauffe lorsque le téléviseur est sous tension pendant une période prolongée (pendant les vacances, par exemple). Marche 12 : 0 am Désactiver Arrêt 12 : 0 am Désactiver Répeter Une fois Volume 10 Contenu TV Dépl. Air Source TV Antenne Câble Chaîne Musique Aucun Photo Aucun Dépl. 3 Retour Réglage TV Heure 1/ 1/ 2007/ 12 : 04 am Horloge Mise en veille Minuterie1 Minuterie2 Minuterie3 TV ► ► ► ► ► : Off : Désactivé : Désactivé : Désactivé Dépl. Appuyer sur la touche EXIT pour quitter le menu. Retour Réglage Contents Réglage de la minuterie de mise en veille Cette minuterie éteint automatiquement le téléviseur après le délai choisi (30, 60, 90, 120, 150 et 180 minutes). 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Heure, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Mise en veille, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner la minute. Le réglage de la minuterie fait passer automatiquement l’Activation sur On. Pour annuler la mise en veille : Appuyer sur la touche ► pour sélectionner Activation. Appuyer sur la touche ▲ ou ▼ pour sélectionner Off, suivie de la touche ENTER. 3 Intro. Retour Mise en veille Régle les options de la minuterie de mise en veille. Minute Activation --- Off ▼ Dépl. TV ▲ Réglage Retour Mise en veille Régle les options de la minuterie de mise en veille. Minute Activation 30 On Dépl. Réglage ▲ RETURN ▼ Retour FAV.CH Appuyer sur la touche SLEEP de la télécommande jusqu’à ce que le délai approprié s’ affiche (n’importe quelle valeur préréglée, de 30 minutes à 180 minutes). Français - 48 BN68-01192F-02Fre_3.indd 48 2007-02-26 ソタネト 6:01:33 Description des fonctions Sélection de la langue de menu Pour pouvoir utiliser les différentes fonctions de minuterie du téléviseur, il faut d’abord régler l’horloge. Cette fonction permet de vérifier l’heure pendant que l’écoute du téléviseur. (Il suffit d’appuyer sur la touche INFO). 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Langue, suivie de la touche ENTER. TV TV 2 Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche EXIT pour quitter. : Off : Moyen Intro. Retour Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche ▲ ou ▼ pour choisir la langue appropriée : English, Español ou Français, suivie de la touche ENTER. ► ► ► ► ► ► ► : Français English : English Español Français : Off : Moyen Intro. Retour Utilisation du mode Jeu Lorsqu’une console de jeu, comme PlayStationMC ou XboxMC, est branchée, la sélection du menu Jeu permet de vivre une expérience de jeu plus réaliste. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Mode Jeu, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. 4 Appuyer sur la touche EXIT pour quitter le menu. ➢ Limites en mode Jeu • Pour débrancher la console de jeu et brancher un autre dispositif externe, régler l’option Jeu à Off dans le menu de configuration. • Si le menu du téléviseur est affiché en mode Jeu, l’écran vibre légèrement. • The mark ( ) s’affiche à l’écran, indiquant que le mode Jeu est activé avec la source sélectionnée. ➢ Si le mode Jeu est activé • Le mode Image passera automatiquement à Jeu et il ne peut être changé. • Le mode Son du menu Son est désactivé. Régler le son à l’aide de l’égaliseur. • La fonction Rétablir du menu Son est activée. La fonction Rétablir initialise les paramètres de l’égaliseur aux réglages par défaut. Le ➢ mode Jeu n’est pas offert en mode TV/Antenne. ➢ Si la qualité de l’image est mauvaise lorsqu’un dispositif externe est branché au téléviseur, vérifier si le mode Jeu est activé. Régler le mode Jeu à Off et brancher les dispositifs externes. TV Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. TV ► ► ► ► ► ► ► : Français : Off : Moyen Intro. Retour Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. : Français : Off On Off : Moyen Intro. Retour AV1 Mode Jeu Français - 49 BN68-01192F-02Fre_3.indd 49 2007-02-26 ソタネト 6:01:36 Affichage des sous-titres codés (messages à l’écran) - numériques La fonction de sous-titrage numérique est compatible avec les canaux numériques. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Sous-titrage, suivie de la touche ENTER. 3 Appuyer sur ENTER pour choisir Sous-titrage. Appuyer sur la touche ▲ ou ▼ pour sélectionner On, suivie de la touche ENTER. 4 Appuyer sur la touche ▲ ou ▼ pour sélectionner Format, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner l’option de sous-titrage désirée, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner les options de sous-menu désirées (voir les options ci-dessous), suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter. ➢ L’option de sous-titrage dépend du programme diffusé. ➢ L’expression Par défaut signifie revenir aux choix de sous-titrage initiaux déterminés par le diffuseur. ➢ L’avant-plan et l’arrière-plan ne peuvent être de la même couleur. ➢ Les paramètres Opacité avant-plan et Opacité arrière-plan ne peuvent être tous deux réglés sur Transparent. • Format : Cette option permet de choisir entre Par défaut, Petit, Standard et Large. La sélection par défaut est Par défaut. • Style des police : Cette option permet de choisir entre Par défaut eStyle0 à Style7. Il est possible de choisir le style de police. La sélection par défaut est Par défaut. • Couleur avant-plan : Cette option permet de choisir entre Par défaut, Blanc, Noir, Rouge, Vert, Bleu, Jaune, Magenta et Cyan. Il est possible de modifier la couleur du lettrage.La sélection par défaut est Par défaut. • Couleur arrière-plan : Cette option permet de choisir entre Par défaut, Blanc, Noir, Rouge, Vert, Bleu, Jaune, Magenta et Cyan. Il est possible de choisir la couleur d’arrièreplan des sous-titres. La sélection par défaut est Par défaut. • Opacité avant-plan : Cette option permet de choisir entre Par défaut, Transparent, Translucide, Solide et Clignotant. Il est possible de modifier l’opacité des caractères. • Opacité arrière-plan : Cette option permet de choisir entre Par défaut, Transparent, Translucide, Solide et Clignotant. Il est possible de modifier l’opacité d’arrière-plan du sous-titrage. • Retour par défaut : Cette option rétablit les paramètres par défaut des fonctions suivantes : Format, Style de police, Couleur d’avant-plan, Couleur d’arrière-plan, Opacité d’avantplan et Opacité d’arrière-plan. Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. TV ► ► ► ► ► ► ► : Français : Off : Moyen Intro. Retour Sous-titres Sous-titres : Off Off Mode ss-titres codés : Par Ondéfaut Options de sous-titres Appuyer sur la touche ▲ ou ▼ pour sélectionner Mode Sous-titrage, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner le sous-menu désiré (Par défaut, Service1 à Service6, CC1 à CC4 ou Texte1 à Texte4), suivie de la touche ENTER. 5. Appuyer sur la touche ▲ ou ▼ pour sélectionner Sous-titrage, suivie de la touche ENTER. 6 TV Dépl. TV Intro. Retour Sous-titres Sous-titres : On Mode ss-titres codés : Par défaut Options de sous-titres Dépl. TV Intro. ► ► ► Retour Sous-titres Sous-titres : Off Par défaut Mode ss-titres codés : Par défaut Service1 Service2 Options de sous-titres Service3 Service4 Service5 Service6 CC1 ▼ Dépl. TV Intro. Sous-titres Sous-titres : On Mode ss-titres codés : Par défaut Options de sous-titres Dépl. TV Intro. ► ► ► Retour Options de sous-titres Format Style des polices Couleur avant-plan Couleur arrière-plan Opacité avant-plan Opacité arrière-plan Retour par défaut : Par défaut : Par défaut : Par défaut : Par défaut : Par défaut : Par défaut RETURN Dépl. Intro. ► ► ► ► ► ► ► Retour FAV.CH Appuyer sur la touche CAPTION de la télécommande pour sélectionner On ou Off. Français - 50 BN68-01192F-02Fre_3.indd 50 2007-02-26 ソタネト 6:01:39 Affichage des sous-titres codés (messages à l’écran) - analogiques La fonction sous-titres codés analogiques fonctionne en mode canal TV analogique ou en mode signal externe. (Selon le signal émetteur, la fonction de sous-titrage analogique peut fonctionner sur les canaux numériques.) 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. TV Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche ▲ ou ▼ pour sélectionner Sous-titrage, suivie de la touche ENTER. TV ► ► ► ► ► ► ► : Français : Off : Moyen Intro. Retour Sous-titres Sous-titres : Off Off Mode ss-titres codés : Par Ondéfaut Options de sous-titres Dépl. 3 Appuyer sur ENTER pour choisir Sous-titrage. Appuyer sur la touche ▲ ou ▼ pour sélectionner On, suivie de la touche ENTER. TV Sous-titres TV Appuyer sur la touche ▲ ou ▼ pour sélectionner Mode ss-titres codés, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner le sousmenu désiré (CC1 à CC4 ou Text 1 à Text 4), suivie de la touche ENTER. Retour Sous-titres : On Mode ss-titres codés : Par défaut Options de sous-titres Dépl. 4 Intro. Intro. ► ► ► Retour Sous-titres Par défaut Sous-titres : Off CC1 Mode ss-titres codés : Par défaut CC2 Options de sous-titres CC3 CC4 Text 1 Text 2 Text 3 Text 4 Appuyer sur la touche EXIT pour quitter le menu. Dépl. Intro. Retour • La sélection par défaut est Par défaut. • CC1 :Le principal service de sous-titrage synchronisé. Il s’agit de sous-titrages dans la langue principalequi doivent être synchronisées avec le son, correspondant préférablement à un cadre particulier. • CC2 : Sous-titrage non synchronisés particulier. Ce canal transmet des données qui ont pour fonction d’accroître l’information transmise par le programme. • CC3 : Service de sous-titrage secondaire synchronisé. Programme alternatifde données de sous-titrage, généralement dans une seconde langue. • CC4 : Sous-titrage non synchronisés particulier. Option semblable à CC2. • Text 1 : Premier service de texte. Il peut comprendre diverses données qui ne se rapportent pas au programme. • Text 2 : Deuxième service de texte. Données supplémentaires, qui en général ne se rapportent pas au programme. • Text 3/Text 4 :Troisième et quatrième services de texte. Ces canaux de données ne doivent être utilisés que si les fonctions d’affichage Text 1 and Text 2 sont insuffisantes. ➢ • La fonction Sous-titrage n’est pas accessible dans les modes COMPOSANT, PC et HDMI(DVI). • L’accessibilité au sous-titrage dépend de l’émission diffusée. Il est aussi possible d’appuyer sur la touche CAPTION de la télécommande pour régler les sous-titrages à On ou Off. RETURN FAV.CH Français - 51 BN68-01192F-02Fre_3.indd 51 2007-02-26 ソタネト 6:01:43 Niveau de transparence Cette fonction permet de régler la transparence de l’écran du menu. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. TV Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche ▲ ou ▼ pour sélectionner Transparence menu, suivie de la touche ENTER. TV 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner le niveau, suivie de la touche ENTER. : Off : Moyen Intro. Retour Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche EXIT pour quitter. ► ► ► ► ► ► ► : Français : Français : Off Haute Moyen Basse Opaque : Moyen Intro. Retour Réglage de l’effet lumineux Vous pouvez activer et désactiver la DEL bleue située à l’avant du téléviseur. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. • Off : La DEL est toujours éteinte. • Mode veille : La DEL s’allume lorsque le téléviseur est en mode de mise en veille et s’éteint lorsque le téléviseur est allumé. • Pen. ècoute : La DEL s’allume lorsque le téléviseur est allumé et s’éteint lorsque le téléviseur est éteint. • Toujours: La DEL est toujours allumée. Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ Appuyer sur la touche ▲ ou ▼ pour sélectionner Effet lumière, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Off, Mode veille, Pen. ècoute ou Toujours, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ TV TV ► ► ► : Off ► : Pen. ècoute ► : Off ► : Off : Moyen Intro. Retour Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ : Off : Moyen Off Mode veille : Off Pen.ècoute ècoute : Pen. Toujours : Off Intro. Retour Régler l’effet lumière à Off pour réduire la consommation d’énergie. Français - 52 BN68-01192F-02Fre_3.indd 52 2007-02-26 ソタネト 6:01:45 Fonction économiseur d’énergie Cette option ajuste la consommation électrique de l’appareil et permet de faire des économies d’énergie. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. TV Appuyer sur la touche ▲ ou ▼ pour sélectionner Économiseur énergie, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner Off, Basse, Moyen ou Haute, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ TV ► ► ► : Off ► : Pen. ècoute ► : Off ► : Off : Moyen Intro. Retour Configuration Plus Écran Bleu Mélodie PC PC cinéma maison Effet lumière Économiseur énergie ▼ Plus Dépl. ▲ • Off : Met le mode économiseur d’énergie hors fonction. • Basse : Fonctionne en mode standard. • Moyen : Passe au mode d’économie d’énergie moyen. • Élevé : Passe au mode d’économie d’énergie élevé. : Off : Moyen Off : Off Basse ècoute : Pen. Moyen Haute : Off Intro. Retour Prévention de la brûlure d’écran Pour réduire les risques de brûlure d’écran, cet appareil est doté d’une technologie de protection contre la brûlure d’écran. Cette technologie permet de régler le déplacement de l’image vers le haut et vers le bas (lignes verticales) et de droite à gauche et inversement (points horizontaux). L’option “Délai” permet de programmer en minutes le délai entre les défilements d’images. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Protection grillage écran (Screen Burn Protection), suivie de la touche ENTER. 3 Appuyer sur la touche ENTER pour choisir Déplac.. Point, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour permuter entre On et Off. S’affichent également les options Point horiz., Ligne verticale et Heure. TV Configuration Plus Protection grillage écran ► Nv nr HDMI : Normal ► Mode Film : Off ► Réglage du support mural ► ISI ► Function d’aide : On ► Mise à niveau du logiciel ► Dépl. Intro. Retour ▲ TV Protection grillage écran Déplac. Point Blanc Défilement Bords gris • Déplac.. point) : Cette fonction permet de déplacer avec une très grande précision les points à l’écran, verticalement et horizontalement, afin d’éviter la présence d’images rémanentes. 4 • Condition optimale pour le déplacement des points à l’écran; Point horizontal 1 TV/AV1/AV2/S-Vidéo/ Composante/HDMI 2 Ligne verticale 1 2 Heure (min) 2 2 Intro. Dépl. TV : On Off : 2On :2 :2 Intro. Retour Déplac. Point Déplac. Point Point horiz. Ligne verticale Heure Dépl. Appuyer sur la touche EXIT pour quitter le menu. Retour Déplac. Point Déplac. Point Point horiz. Ligne verticale Heure Appuyer sur la touche ▲ ou ▼ pour choisir l’élément à modifier, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour modifier la valeur de l’élément, suivie de la touche ENTER. PC : Foncé Dépl. TV ► ► ► ► : On : 20 : 21 : 12 3 4 Intro. Retour Français - 53 BN68-01192F-02Fre_3.indd 53 2007-02-26 ソタネト 6:01:47 Réduction des effets de la brûlure d’écran S’il y a eu brûlure d’écran, il est possible de sélectionner un écran blanc ou un défilement pour supprimer les traces de brûlure à l’écran. 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Protection grillage écran , suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Blanc, Défilement, ou Bords gris, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. TV Protection grillage écran Déplac. Point Blanc Défilement Bords gris Dépl. TV Blanc Cette fonction permet de supprimer les images rémanentes à l’écran en changeant la couleur des points en blanc. Utiliser cette fonction lorsque l’écran présente des symboles ou des images rémanentes, tout particulièrement lorsqu’une image fixe est affichée pendant une période prolongée. Défilement Cette fonction permet de supprimer les images rémanentes en déplaçant tous les points à l’écran au plasma sur un parcours prédéfini. Utiliser cette fonction lorsque l’écran présente des symboles ou des images rémanentes, tout particulièrement lorsqu’une image fixe est affichée pendant une période prolongée. : Foncé Intro. Retour Protection grillage écran Déplac. Point Blanc Défilement Bords gris Dépl. TV ► ► ► ► : Foncé Intro. Retour Protection grillage écran Déplac. Point Blanc Défilement Bords gris Bords gris Lorsque le téléviseur est regardé en format d’écran 4:3, les dommages à l’écran sont empêchés en ajustant l’équilibre des blancs de l’extrême gauche et de l’extrême droite. Pour éviter une brûlure d’écran, sélectionner Sombre ou Clair. ► ► ► ► Dépl. : Foncé Foncé Clair Intro. Retour • Foncé : Lorsque le format de l’image est réglé à 4:3, les côtés gauche et droit sont plus foncés. • Clair : Lorsque le format de l’image est réglé à 4:3, les côtés gauche et droit sont plus clairs. ➢ ➢ ➢ Pour supprimer les images rémanentes à l’écran, utiliser la fonction Blanc ou Défilement. Bien que ces deux fonctions suppriment les images rémanentes à l’écran, la fonction Défilement est la plus efficace. Pour atteindre sa pleine efficacité, la fonction de suppression des images rémanentes doit être activée pendant une longue période (environ 1 heure). Si les images rémanentes n’ont pas été supprimées après avoir exécuté la fonction, recommencer l’opération. Appuyer sur n’importe quelle touche de la télécommande pour annuler cette fonction. Réglage des fonctions d’aide Affiche l’aide dans le menu des fonctions. TV 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Fonction d’aide, suivie de la touche ENTER. Configuration Plus Protection grillage écran ► Nv nr HDMI : Normal ► Mode Film : Off ► Réglage du support mural ► ISI ► Function d’aide : On ► Mise à niveau du logiciel ► Dépl. Retour Intro. ▲ TV 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Off ou On, suivie de la touche ENTER. Appuyer sur la touche EXIT pour quitter le menu. ➢ Le paramètre par défaut de la fonction d’aide est On. Configuration Plus Protection grillage écran Nv nr HDMI : Normal : Off Mode Film Réglage du support mural ISI Off Function d’aide : On On Mise à niveau du logiciel Dépl. Retour Intro. ▲ Français - 54 BN68-01192F-02Fre_3.indd 54 2007-02-26 ソタネト 6:01:50 Ajustement fixation murale (vendue séparément) Lorsque le support mural est monté, la position du téléviseur peut être facilement ajustée. Auto fixation murale Panneau arrière du téléviseur Câble EX-LINK (non fourni) Pour entrer dans le menu TV 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner Réglage du support mural, suivie de la touche ENTER. 3 Ajustez à la position désirée à l’aide de la touche ▲/▼/◄/►. Configuration Plus Protection grillage écran ► Nv nr HDMI : Normal ► Mode Film : Off ► Réglage du support mural ► ISI ► Function d’aide : On ► Mise à niveau du logiciel ► Dépl. Retour Intro. ▲ Réglage du support mural Position1 Appuyer sur la touche EXIT pour quitter le menu. ➢ Si vous appuyez sur une touche fléchée lorsqu’il n’y a pas d’affichage à l’écran du téléviseur, l’écran d’ajustement s’affiche alors. ➢ Lorsque vous mettez le téléviseur hors tension, il se remet dans sa position initiale. Lorsque vous mettez le téléviseur sous tension, il se met dans la dernière position enregistrée. Position Réglage 1 INFO 2 Centre 3 Sorite À l’aide de la touche de la télécommande Touche ➢ ➢ ➢ Actions Ajustement de l’angle de la fixation murale Incliner vers le haut, incliner vers le bas, déplacer vers la droite, déplacer vers la gauche Rétablir Rétablit dans la position initiale Mémorisation de la position et passage à la position enregistrée Les touches rouge, verte et jaune permettent de mémoriser trois positions. Les trois touches de couleur permettent de passer aux positions mémorisées. Pour l’installation, reportez-vous au manuel d’installation fourni. Pour installer le téléviseur ainsi que pour installer et déplacer la fixation murale, assurez-vous de vous adresser à une société spécialisée en installation. Ce dispositif doit être utilisé pour poser la fixation murale sur un mur. Français - 55 BN68-01192F-02Fre_3.indd 55 2007-02-26 ソタネト 6:01:53 Mise à jour du logiciel Samsung peut offrir des mises à niveau du microprogramme dans le futur. Contacter le centre d’appel Samsung au 1-800-SAMSUNG pour obtenir de l’information sur le téléchargement des mises à jour et sur l’utilisation d’une clé USB. Les mises à jour sont accessibles par le branchement d’une clé USB dans le port USB situé sur le côté du téléviseur. 1 Insérer une clé USB contenant la mise à jour du microprogramme dans le port de mise à jour USB situé sur le côté du téléviseur. 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Mise à niveau du logiciel, suivie de la touche ENTER. 4 Appuyer sur la touche ▲ ou ▼ pour sélectionner USB, suivie de la touche ENTER. Le message Recherche de la clé USB… Délai : jusqu’à 30 secondes. s’affiche. 5 Si le micrologiciel du dispositif USB est correctement détecté, le message suivant s’affiche : remplacer la version xxxx par la version xxxx? L’appareil se réinitialise après la mise à jour. Appuyez sur la touche ◄ ou ► pour choisir OK, puis sur ENTER. La mise à jour est lancée. ��������� TV Configuration Plus Protection grillage écran Nv nr HDMI : Normal Mode Film : Off Réglage du support mural ISI Function d’aide : On Mise à niveau du logiciel Dépl. Intro. ▲ TV ► ► ► ► ► ► ► Retour Mise à niveau du logiciel USB ► Veiller à ne pas débrancher l’alimentation et à ne pas retirer la clé USB pendant l’application des mises à jour. Le téléviseur s’éteint et se remet en marche automatiquement une fois la mise à jour du microprogramme terminée. Vérifier la version du microprogramme une fois les mises à jour terminées. ➢ Le microprogramme et la procédure de mise à jour peuvent varier selon la région et le pays. Dépl. Intro. Retour Mise à niveau du logiciel Recherche de la clé USB… Délai : jusqu’à 30 secondes. Fonction Puce V La fonction Puce V bloque automatiquement la diffusion d’émissions pouvant ne pas convenir aux enfants. L’utilisateur doit entrer un numéro d’identification personnel (NIP) avant de pouvoir configurer ou modifier les restrictions relatives de la V-Chip. ➢ ➢ ➢ 1 2 Quand la fonction V-Chip est activée, la fonction image sur image (ISI) ne fonctionne pas. La fonction V-Chip ne fonctionne pas si l’entrée est réglée sur téléviseur numérique (HD ou SD). La fonction de contrôle parental (V-Chip) n’est pas offerte en mode HDMI ou Composant.Configuration du numéro d’identification personnel (NIP) TV Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner V-Chip, suivie de la touche ENTER. Le message Entrer NIP s’affiche. Entrer le NIP à 4 chiffres. ➢ Le NIP par défaut d’un nouveau téléviseur est 0-0-0-0. Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. TV ► ► ► ► ► ► ► : Français : Off : Moyen Intro. Retour V-Chip Entrez NIP * * * * Suite... 0~9 Entrer NIP Retour Français - 56 BN68-01192F-02Fre_3.indd 56 2007-02-26 ソタネト 6:02:02 3 L’écran V-Chip s’affiche. Appuyer sur la touche ▲ ou ▼ pour sélectionner Changer NIP, suivie de la touche ENTER. L’écran Changer NIP s’affiche. Choisir et saisir quatre chiffres pour le NIP. Entrer de nouveau le code à 4 chiffres. Le message NIP modifié avec succès. est affiché. Le NIP a été enregistré. TV V-Chip Blocage V-Chip : Off Contrôle parental TV Classif. MPAA Catég. américaine téléchargeable Changer NIP ► ► ► ► ► Appuyer sur la touche EXIT pour quitter. ➢ Si le NIP est oublié, appuyer sur les touches de la télécommande dans l’ordre suivant pour rétablir le code 0-0-0-0 : Power Off → MUTE → 8 → 2 → 4 → Power On. Dépl. Intro. Retour <Pour les modèles aux États-Unis seulement> TV V-Chip Blocage V-Chip : Off Contrôle parental TV Classif. MPAA Anglais Canadien Français Canadien Catég. américaine téléchargeable Changer NIP Dépl. Intro. ► ► ► ► ► ► ► Retour <Pour les modèles au Canada seulement> TV Changer NIP Nouveau NIP Confirmer NIP Comment activer et désactiver la fonction Puce V Retour 0~9 Entrer NIP 1 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner V-Chip, suivie de la touche ENTER. Le message Entrer NIP s’affiche. Entrer le NIP à 4 chiffres. TV V-Chip Entrez NIP * * * * Retour 0~9 Entrer NIP 3 L’écran V-Chip s’affiche. Pour activer la fonction V-Chip, appuyer sur la touche ENTER de façon à On le champ Blocage V-Chip. (Appuyer sur la touche ▲ ou ▼ pour permuter entre On et Off). Appuyer sur la touche ENTER. ➢ TV V-Chip Blocage V-Chip : Off Off Contrôle parental TV On Classif. MPAA Anglais Canadien Français Canadien Catég. américaine téléchargeable Changer NIP La fonction Fixe ne peut pas être utilisée lorsque le mode V-Chip est activé. Dépl. Appuyer sur la touche EXIT pour quitter. Intro. Retour Configuration des restrictions à l’aide du système “Contrôle TV parental” Premièrement, créer un numéro d’identification personnel (NIP). Activer ensuite la fonction V-Chip. (consulter la section précédente). Le contrôle parental se configure de deux façons : à l’aide du contrôle parental du téléviseur ou à l’aide des classifications de la MPAA. 1 2 TV Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner V-Chip, suivie de la touche ENTER. Le message Entrer NIP s’affiche. Entrer le NIP à 4 chiffres. Suite... Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. TV ► ► ► ► ► ► ► : Français : Off : Moyen Intro. Retour V-Chip Entrez NIP * * * * 0~9 Entrer NIP Retour Français - 57 BN68-01192F-02Fre_3.indd 57 2007-02-26 ソタネト 6:02:05 3 4 L’écran V-Chip s’affiche. Appuyer sur la touche ▲ ou ▼ pour sélectionner Contrôle parental TV, suivie de la touche ENTER. L’écran Contrôle parental TV s’affiche. Appuyer sur la touche ▲ ou ▼ pour sélectionner une des six classifications, établies en fonction de l’âge. • TV-Y : Tous les enfants. Les thèmes et éléments de cette émission ont été spécialement conçus pour un public très jeune, notamment les enfants de deux à six ans. • TV-Y7 : Vise des enfants plus vieux. Les thèmes et éléments de cette émission peuvent comprendre un certain niveau de violence physique ou de comédie, ou peut faire peur aux enfants de moins de sept ans. • TV-G : Public de tous âges. Cette émission ne comporte aucune ou peu de violence, aucun langage rude ni dialogue ou situation à connotation sexuelle. • TV-PG : Surveillance parentale recommandée. Cette émission peut contenir du langage grossier peu fréquent, de la violence limitée ainsi que certaines situations ou dialogues à connotation sexuelle. • TV-14 : Supervision des parents fortement recommandée. Cette émission peut inclure des thèmes évolués, des scènes à connotation sexuelle, du langage rude et de la violence plus intense. • TV-MA : Adultes seulement. Cette émission peut inclure des thèmes destinés aux adultes, un langage vulgaire, de la violence explicite et des scènes à connotation clairement sexuelle. 5 TV V-Chip Blocage V-Chip : On Contrôle parental TV Classif. MPAA Anglais Canadien Français Canadien Catég. américaine téléchargeable Changer NIP Dépl. TV Intro. ► ► ► ► ► ► ► Retour Contrôle parental TV Perm. Tout Bloq. Tout Dépl. Intro. Retour À ce moment, une des classifications est sélectionnée. Appuyer sur la touche ENTER. En fonction de la configuration existante, le symbole “ ” est sélectionné. (Vide = Débloqué, = Bloqué) Pendant que le symbole “ ” est sélectionné, appuyer sur la touche ENTER pour bloquer ou débloquer la classification. Pour choisir une classification différente, appuyer sur la touche ▲ or ▼ et répéter les étapes précédentes. ➢ Perm. tout : Appuyer sur cette touche pour débloquer toutes les classifications. Bloq. tout : Appuyer sur cette touche pour bloquer toutes les classifications. ➢ Les classifications TV-Y7-, TV-Y7+, TV-G, TV-SP, TV-14 et TV-A comportent des options supplémentaires. Voir l’étape suivante pour changer les sousclassifications ci-dessous : • FV : Fantastique, violence. • D : Dialogues à connotation sexuelle. • L : Langage pour adultes. • S : Situations à connotation sexuelle. • V : Violence. La fonction V-Chip permet de bloquer automatiquement certaines classifications “plus restrictives”. Par exemple, si la classification TV-Y est bloquée, la classification TV-Y7 est automatiquement bloquée. De la même façon, si la classification TV-G est bloquée, toutes les classifications du groupe “jeunes adultes” sont aussi bloquées (TV-G, TV-PG, TV-14 et TVMA). Les sous-classifications (D, L, S et V) sont regroupées de la même façon. (Consulter la prochaine section.) Configuration des sous-classifications FV, D, L, S et V Pour commencer, sélectionner une des classifications suivantes : TV-7-, TV-7+, TV-G, TV-SP, TV14 ou TV-A (voir l’étape 4); appuyer ensuite sur la touche ENTER. Le symbole “ ” s’affiche pour chaque sous-classification. Lorsque le symbole “ ” est sélectionné, appuyer sur la touche ► pour accéder à une sous-classification. Appuyer sur la touche ENTER pour bloquer la sous-classification. Pour choisir une classification différente, appuyer sur la touche ▲ or ▼ et répéter les étapes précédentes. Appuyer sur la touche EXIT pour quitter tous les écrans. (ou passer à la section suivante et configurer des restrictions supplémentaires selon les codes MPAA). ➢ Ces classifications se répartissent en deux groupes distincts : TV-Y- et TVY7+ (jusqu’à 7 ans) et TV-G à TV-A (tous les autres). Les restrictions de ces deux groupes s’appliquent indépendamment : Si une famille compte de très jeunes enfants ainsi que de jeunes adultes, les classifications doivent être définies séparément pour ces groupes. ➢ 6 7 Français - 58 BN68-01192F-02Fre_3.indd 58 Suite... 2007-02-26 ソタネト 6:02:06 Configuration des restrictions à l’aide des catégories MPAA (G, PG, PG-13, 18+, NO-17, X et NR) Le système de classification MPAA, qui est basé sur les codes établis par la Motion Picture Association of America (MPAA), s’applique surtout aux longs métrages. Si la fonction V-Chip est activée, les émissions classées offensantes (système de classification des émissions ou MPAA) sont automatiquement bloquées. 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. TV Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche ▲ ou ▼ pour sélectionner V-Chip, suivie de la touche ENTER. Le message Entrer NIP s’affiche. Entrer le NIP à 4 chiffres. TV ► ► ► ► ► ► ► : Français : Off : Moyen Retour Intro. V-Chip Entrez NIP 3 * L’écran V-Chip s’affiche. Appuyer sur la touche ▲ ou ▼ pour sélectionner Catégories MPAA, suivie de la touche ENTER. * * * Retour 0~9 Entrer NIP TV 4 Blocage V-Chip : On Contrôle parental TV Classif. MPAA Anglais Canadien Français Canadien Catég. américaine téléchargeable Changer NIP Appuyer sur la touche ▲ ou ▼ pour sélectionner la restriction appropriée. Appuyer sur la touche ENTER pour activer la restriction sélectionnée. Le symbole “ ” s’affiche. Pendant que le symbole “ ” est sélectionné, appuyer sur la touche ENTER pour bloquer ou débloquer la classification. Appuyer sur la touche EXIT pour quitter le menu. ➢ Perm. tout : Appuyer sur cette touche pour débloquer toutes les classifications. Bloq. tout : Appuyer sur cette touche pour bloquer toutes les classifications. Dépl. TV ► ► ► ► ► ► ► Retour Intro. Classif. MPAA Perm. Tout Bloq. Tout • G : Public de tous âges (aucune restriction). • PG :Surveillance parentale recommandée. • PG-13 :Supervision des parents fortement recommandée. • R :Réservé aux adultes. Les enfants de moins de 17 ans devraient être accompagnés d’un adulte. • NC-17 :Non recommandé pour les enfants de moins de 17 ans. • X :Adultes seulement. • NR : Non classé ➢ V-Chip Dépl. Intro. Retour La fonction V-Chip bloque automatiquement toute classification “plus restrictive”. Par exemple, si la classification PG-13 est bloquée, les classifications R, NC-17 et X sont automatiquement bloquées. Configuration des restrictions à l’aide de l’option Anglais canadien (pour les modèles canadiens) : 1 2 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. TV Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Appuyer sur la touche ▲ ou ▼ pour sélectionner V-Chip, suivie de la touche ENTER. Le message Entrer NIP s’affiche. Entrer le NIP à 4 chiffres. TV ► ► ► ► ► ► ► : Français : Off : Moyen Intro. Retour V-Chip Entrez NIP * * * * Suite... 0~9 Entrer NIP Retour Français - 59 BN68-01192F-02Fre_3.indd 59 2007-02-26 ソタネト 6:02:10 3 L’écran V-Chip s’affiche. Appuyer sur la touche ▲ ou ▼ pour sélectionner Anglais canadien, suivie de la touche ENTER. 4 Appuyer sur la touche ▲ ou ▼ pour sélectionner la restriction appropriée. Appuyer sur la touche ENTER pour activer la restriction sélectionnée. Le symbole “ ” s’affiche. Appuyer sur la touche EXIT pour quitter le menu. ➢ Perm. tout : Appuyer sur cette touche pour débloquer toutes les classifications. Bloq. tout : Appuyer sur cette touche pour bloquer toutes les classifications. TV Dépl. TV ► ► ► ► ► ► ► Retour Intro. Anglais Canadien Perm. Tout Bloq. Tout •C: Émissions destinées aux enfants de moins de 8 ans. • C8+ : Émissions convenant généralement aux enfants de 8 ans et plus, sans surveillance. • G : Émissions grand public convenant à tous les auditoires. • PG : Surveillance parentale. • 14+ : Émissions dont la teneur peut ne pas convenir, en tout ou en partie, aux auditeurs de moins de 14 ans. • 18+ : Émissions pour adultes. ➢ V-Chip Blocage V-Chip : On Contrôle parental TV Classif. MPAA Anglais Canadien Français Canadien Catég. américaine téléchargeable Changer NIP Dépl. Retour Intro. La fonction V-Chip bloque automatiquement toute classification “plus restrictive”. Par exemple, si la classification G est bloquée, les classifications PG, 14+ et 18+ sont automatiquement bloquées. Configuration des restrictions à l’aide de l’option Français canadien (pour les modèles canadiens) : 1 2 3 4 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. TV Appuyer sur la touche ▲ ou ▼ pour sélectionner V-Chip, suivie de la touche ENTER. Le message Entrer NIP s’affiche. Entrer le NIP à 4 chiffres. L’écran V-Chip s’affiche. Appuyer sur la touche ▲ ou ▼ pour sélectionner Français canadien, suivie de la touche ENTER. TV Appuyer sur la touche ▲ ou ▼ pour sélectionner la restriction appropriée. Appuyer sur la touche ENTER pour activer la restriction sélectionnée. Le symbole “ ” s’affiche. Appuyer sur la touche EXIT pour quitter le menu. Perm. tout : Appuyer sur cette touche pour débloquer toutes les classifications. Bloq. tout : Appuyer sur cette touche pour bloquer toutes les classifications. ➢ : Off : Moyen Retour Intro. V-Chip * * * * Retour 0~9 Entrer NIP TV V-Chip Blocage V-Chip : On Contrôle parental TV Classif. MPAA Anglais Canadien Français Canadien Catég. américaine téléchargeable Changer NIP Général. Émissions non recommandées pour les jeunes enfants. Émissions pouvant ne pas convenir aux enfants de moins de 13 ans. Émissions ne convenant pas aux enfants de moins de 16 ans. Émissions réservées aux adultes. La fonction V-Chip bloque automatiquement toute classification “plus restrictive”. Par exemple, si la classification 8 ans+ est bloquée, les classifications 13 ans+, 16 ans+ et 18 ans+ sont automatiquement bloquées. ► ► ► ► ► ► ► : Français Entrez NIP ➢ •G: • 8 ans+ : • 13 ans+ : • 16 ans+ : • 18 ans+ : Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. Dépl. TV Intro. ► ► ► ► ► ► ► Retour Français Canadien Perm. Tout Bloq. Tout Dépl. Intro. Retour Français - 60 BN68-01192F-02Fre_3.indd 60 2007-02-26 ソタネト 6:02:12 Fonction V-Chip pour les canaux numériques Il est possible d’utiliser les informations relatives au contrôle parental pour l’écoute de canaux numériques. 1 2 3 4 Appuyer sur la touche MENU pour afficher le menu. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner V-Chip, suivie de la touche ENTER. Le message Entrer NIP s’affiche. Entrer le NIP à 4 chiffres. L’écran V-Chip s’affiche. Appuyer sur la touche ▲ ou ▼ pour sélectionner Catég. américaine téléchargeable, suivie de la touche ENTER. ➢ S’il n’est pas possible de télécharger les informations de la station émettrice, le menu Catég. américaine téléchargeable est désactivé. ➢ Les informations relatives au contrôle parental sont automatiquement téléchargées pendant le visionnement de canaux numériques. Cela peut prendre quelques secondes. ➢ Le menu Catég. américaine téléchargeable est de nouveau accessible une fois les informations téléchargées de la station émettrice. Cependant, selon les informations de la station émettrice, elle pourrait ne pas être accessible. Appuyer sur la touche ▲ ou ▼ pour sélectionner la restriction appropriée. Appuyer sur la touche ENTER pour activer la restriction sélectionnée. Le symbole “ ” s’affiche. Appuyer sur la touche EXIT pour quitter le menu. ➢ Perm. tout : Appuyer sur cette touche pour débloquer toutes les classifications. Bloq. tout : Appuyer sur cette touche pour bloquer toutes les classifications. ➢ Les niveaux de contrôle parentale varient selon la station émettrice. ➢ Le nom de menu par défaut et les modifications de catégories américaines téléchargeables varient selon les informations téléchargées. ➢ Même si l’affichage à l’écran est dans une autre langue, le menu Catég. américaine téléchargeable ne s’affiche qu’en anglais. ➢ La classification permet de bloquer automatiquement certaines classifications plus restrictives. ➢ Les titres de classification (par exemple : Humor Level) et les classifications (par exemple : DH, MH, H) peuvent varier selon la station émettrice. TV Configuration Prêt à l’emploi Langue Heure Mode Jeu V-Chip Sous-titres Transparence menu ▼ Plus Dépl. TV ► ► ► ► ► ► ► : Français : Off : Moyen Retour Intro. V-Chip Entrez NIP * * * * Retour 0~9 Entrer NIP TV V-Chip Blocage V-Chip : On Contrôle parental TV Classif. MPAA Anglais Canadien Français Canadien Catég. américaine téléchargeable Changer NIP Dépl. Titre de la catégorie TV Intro. ► ► ► ► ► ► ► Retour Le nombre de catégories en cours Catég. américaine téléchargeable Humor Level ► 1/2 Perm. Tout Bloq. Tout DH MH H VH EH Dépl. Intro. Retour Le nombre total de catégories Réinitialisation du téléviseur lorsque la fonction V-Chip bloque un canal (solution d’urgence). Si un canal à accès restreint est syntonisé, la fonction V-Chip la bloque. L’écran devient vide et le message suivant s’affiche : 1 1 2 3 Entrer le NIP. Pour rétablir l’image, syntoniser une autre chaîne à l’aide des touches CH ou CH . Dans certains cas (selon la classification des programmes de télévision locaux), la fonction Puce V permet de bloquer tous les canaux. Dans ce cas, utiliser la touche V-Chip en guise de solution d’urgence. Appuyer sur la touche MENU. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner V-Chip, suivie de la touche ENTER. Entrer le NIP et appuyer sur la touche ENTER, suivie la touche ▲ ou ▼ pour désactiver temporairement la fonction Blocage V-Chip. ➢ Si le NIP est oublié, appuyer sur les touches de la télécommande dans l’ordre suivant pour rétablir le code 0-0-0-0 : Power Off → MUTE → 8 → 2 → 4 → Power On. La chaîne est bloquée TV-PG[ S ] Entrer NIP sur les touches num. pour débloquer toutes les chaînes. Presser EXIT pour effacer le NIP MENU pour afficher menu principal. La chaîne est bloquée TV-PG[ L ] Entrer NIP sur les touches num. pour débloquer toutes les chaînes. Presser EXIT pour effacer le NIP MENU pour afficher menu principal. Français - 61 BN68-01192F-02Fre_3.indd 61 2007-02-26 ソタネト 6:02:14 À propos d’Anynet+ Qu’est-ce qu’Anynet+? Anynet+ est un système de réseau audiovisuel qui permet, à l’aide de la télécommande Samsung, de commander tous les appareils audiovisuels Samsung raccordés. Branchement d’appareils Anynet+ Le système Anynet+ peut être utilisé uniquement avec les appareils audiovisuels Samsung équipés de la fonction Anynet+. Pour vous assurer que votre appareil audiovisuel Samsung est doté de cette fonction, vérifiez si une marque Anynet+ figure sur votre appareil. Pour brancher directement au téléviseur TV Anynet+ Appareil 1 Câble HDMI 1.3 Câble HDMI 1.3 Anynet+ Appareil 2 Anynet+ Appareil 3 Raccorder la prise HDMI1, HDMI2 ou HDMI3 du téléviseur à la prise de sortie HDMI OUT de l’appareil Anynet+ correspondant à l’aide du câble HDMI. Câble HDMI 1.3 Pour brancher à un cinéma maison TV Anynet+ Appareil 1 Câble HDMI 1.3 Câble HDMI 1.3 Anynet+ Appareil 3 Cinéma maison Câble optique ➢ ➢ ➢ ➢ ➢ ➢ Câble HDMI 1.3 1 Raccorder la prise HDMI1,HDMI2 ou HDMI3 du téléviseur à la prise de sortie HDMI OUT de l’appareil Anynet+ correspondant à l’aide du câble HDMI. 2 Raccorder la prise d’entrée HDMI IN du cinéma maison et la prise de sortie HDMI OUT de l’appareil Anynet+ correspondant à l’aide du câble HDMI. Anynet+ Appareil 2 Câble HDMI 1.3 Brancher le câble optique entre la sortie audionumérique optique du téléviseur et l’entrée audionumérique du système de cinéma maison. Ne brancher qu’ un seul système de cinéma maison. Il est possible d’écouter le son en 5.1 canaux par les haut-parleurs du cinéma maison. Autrement, les autres cas ne permettent que l’écoute du son stéréo de 2 canaux. Veiller à ce que l’entrée audionumérique optique du cinéma maison et le téléviseur soient bien branchés afin de pouvoir écouter le son par le cinéma maison. Cela étant, il n’est pas possible d’écouter le son provenant de l’enregistreur et envoyé au cinéma maison par le son à 5.1 canaux, étant donné que le téléviseur n’émet qu’un son stéréo en 2 canaux. Consulter le manuel du cinéma maison. Il est possible de brancher un appareil Anynet+ à l’aide du câble HDMI 1.3 Certains câbles HDMI ne prennent pas en charge des fonctions Anynet+. Anynet+ fonctionne lorsque l’appareil audiovisuel qui le prend en charge est à l’état de veille ou en marche. Anynet+ prend en charge un maximum de 12 appareils audiovisuels. Français - 62 BN68-01192F-02Fre_4.indd 62 2007-02-26 ソタネト 6:05:53 Configuration d’Anynet+ Les paramètres suivants permettent d’utiliser les fonctions Anynet+. Pour utiliser la fonction Anynet+, le Anynet+ (HDMI-CEC) doit être activé. 1 2 Appuyer sur la touche Anynet+. Appuyer sur la touche ▲ ou ▼ pour sélectionner Configuration, suivie de la touche ENTER. Appuyer sur la touche ENTER pour sélectionner Anynet+ (HDMI-CEC), suivie à nouveau de la touche ENTER. TV Air 28 Enregistrer: Configuration Dépl. 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner marche, suivie de la touche ENTER. ➢ La fonction Anynet+ (HDMI-CEC) est activée. ➢ Si Off est sélectionné, la fonction Anynet+ (HDMI-CEC) est désactivée. ➢ Lorsque la fonction de Anynet+ (HDMI-CEC) est désactivée, toutes les opérations Anynet+ connexes sont désactivées. marche Brancher Enregistrer Sorite Intro. Anynet+ Configuration Anynet+ (HDMI-CEC) : Offarrêt Arrêt automatique : Offmarche Recherche de connexions Intro. Dépl. Retour Régler un appareil Anynet+ de sorte qu’il s’arrête automatiquement lorsque le téléviseur est hors tension 2 3 Appuyer sur la touche ▲ ou ▼ pour sélectionner Arrêt automatique, suivie de la touche ENTER. Appuyer sur la touche ▲ ou ▼ pour sélectionner marche, suivie de la touche ENTER. ➢ La fonction Arrêt automatique est activée. ➢ Si arrêt est sélectionné, la fonction Arrêt automatique est désactivée. Anynet+ Configuration Anynet+ (HDMI-CEC) : marche Arrêt automatique : Off arrêt Recherche de connexions marche Intro. Dépl. Retour Appuyer sur la touche EXIT pour quitter le menu. ➢ ➢ Le paramètre d’appareil sélectionné de la télécommande du téléviseur doit être réglé à TV pour pouvoir utiliser la fonction Anynet+. Si l’Arrêt automatique est activé, les appareils externes branchés sont également éteints en même temps que le téléviseur. Cependant, si l’appareil est en mode d’enregistrement, il ne pourra être éteint. Balayage et permutation entre les appareils Anynet+ 1 Appuyer sur la touche Anynet+. La liste des appareils Anynet+ branchés au téléviseur s’affiche. ➢ 2 Appuyer sur la touche ▲ ou ▼ pour sélectionner un appareil particulier, suivie de la touche ENTER. Le système commande l’appareil sélectionné. 3 S’il est impossible de trouver l’appareil désiré, appuyer sur la touche ▲ ou ▼ pour sélectionner Recherche de connexions, suivie de la touche ENTER. Le message Configuration de la connexion Anynet+… s’affiche. Lorsque la recherche d’appareil est terminée, les appareils branchés sont énumérés dans le menu Anynet+. ➢ ➢ ➢ ➢ ➢ Permuter vers les appareils sélectionnés peut prendre jusqu’à 2 minutes. Il n’est pas possible d’annuler l’opération de permutation. La durée nécessaire au balayage des appareils dépend du nombre d’appareils branchés. Lorsque le balayage est terminé, le nombre d’appareils trouvés n’est pas affiché. Bien que le téléviseur recherche automatiquement tous les appareils lorsqu’il est mis en marche à l’aide de la touche POWER, ceux qui sont branchés lorsque le téléviseur est en marche ne sont pas affichés. Dans ce cas, sélectionner Recherche de connexions pour détecter les appareils. Si vous avez sélectionné un appareil audiovisuel externe en appuyant sur la touche SOURCE, il est impossible d’utiliser la fonction Anynet+. Veiller à permuter vers un appareil Anynet+ à l’aide de la touche Anynet+. TV Air 28 Enregistrer: marche Brancher Enregistrer Configuration Dépl. Intro. Sorite Anynet+ Configuration Anynet+ (HDMI-CEC) : marche Arrêt automatique : marche ► ► Recherche de connexions Dépl. Intro. ► Retour Suite... Français - 63 BN68-01192F-02Fre_4.indd 63 2007-02-26 ソタネト 6:05:59 Menu Anynet+ Le menu Anynet+ varie selon le type et l’état des appareils Anynet+ branchés au téléviseur. Menu Anynet+ Regarder la télévision Description + Permuter d’Anynet vers le mode d’émission télévisuel. Enregistrer Démarre l’enregistrement. (Ce menu fonctionne uniquement avec un appareil pouvant enregistrer.) Menu (Nom_Appareil) Affiche le menu de l’appareil raccordé. Exemple : Lorsqu’un enregistreur DVD est branché, le menu principal de l’enregistreur DVD s’affiche. Opération (Nom_Appareil) Affiche le menu de contrôle de lecture de l’appareil raccordé. Exemple : Lorsqu’un enregistreur DVD est branché, le menu de contrôle de lecture de l’ enregistreur DVD s’affiche. Brancher (Nom_Appareil) Le téléviseur se branche à l’appareil correspondant. Récepteur Le son sort par le récepteur (cinéma maison). Mais le téléviseur possède une sortie SPDIF. Le son du téléviseur peut donc être envoyé au système de cinéma maison. Configuration Vous pouvez régler la Anynet+ (HDMI-CEC), la fonction d’arrêt automatique et la détection de connexions pour l’utilisation de la fonction Anynet+. Touches de la télécommande du téléviseur accessibles en mode Anynet+ Type d’appareil État de fonctionnement Touches accessibles Après une permutation vers l’appareil, lorsque le menu de l’appareil correspondant s’affiche à l’écran. Touches numériques ▲/▼/◄/►/Touches ENTER Touches de couleur Touche EXIT Après la permutation vers l’appareil, pendant la lecture d’un fichier ◄◄ (Recherche vers l’arrière) ►► (Recherche vers l’avant) (Arrêt) ► (Lecture/Pause) Appareil Anynet+ Appareil avec syntoniseur intégré Après la permutation vers l’appareil, pendant l’écoute CH Touche ▲/▼ d’une émission télévisée Appareil audio Lorsque le récepteur est activé Touches VOL +/Touche MUTE Anyview2 En mode d’écoute de la télévision ► (Lecture/Pause) ➢ ➢ ➢ ➢ ➢ ➢ ➢ La fonction Anynet+ n’est accessible que lorsque la télécommande est réglée à TV. La touche REC ne fonctionne qu’à l’état d’écoute de la télévision. Il est impossible de contrôler les appareils Anynet+ à l’aide des touches du panneau latéral du téléviseur Il est possible de contrôler les appareils Anynet+ à l’aide du téléviseur. Il est possible que la télécommande du téléviseur ne fonctionne pas dans certaines conditions. Le cas échéant, resélectionner l’appareil Anynet+. Les fonctions Anynet+ ne fonctionnent pas avec des produits d’autres marques. En mode Anynet+, il se peut que les touches de couleur ne fonctionnent pas correctement. Les fonctions ◄◄, ►► peuvent varier selon l’appareil. Enregistrement Il est possible d’enregistrer une émission télévisée à l’aide d’un enregistreur. Appuyer sur la touche REC. L’enregistrement commence. (Seulement lorsqu’un appareil d’enregistrement Anynet+ est branché.) ➢ L’émission télévisée en cours est enregistrée pendant l’état d’écoute de la télévision. Si un autre vidéo est écouté d’un autre appareil, le vidéo de l’appareil est enregistré. ➢ Avant d’enregistrer, vérifier si la prise d’antenne est correctement branchée à l’appareil enregistreur. Pour la connexion de l’antenne à l’appareil enregistreur, consulter le guide d’utilisation. ➢ Avant d’enregistrer, vérifier si la prise d’antenne est correctement branchée à l’appareil enregistreur. Pour la connexion de l’antenne à l’appareil enregistreur, consulter le guide d’utilisation. Français - 64 BN68-01192F-02Fre_4.indd 64 2007-02-26 ソタネト 6:05:59 Écoute par l’intermédiaire d’un récepteur (cinéma maison) Il est possible d’écouter le son par l’intermédiaire d’un récepteur, plutôt que par les haut-parleurs du téléviseurs. 1 Appuyer sur la touche Anynet+. Appuyer sur la touche ▲ ou ▼ pour sélectionner Récepteur, suivie de la touche ENTER. 2 Appuyer sur la touche ◄ ou ► pour sélectionner marche, suivie de la touche ENTER. Il à présent possible d’écouter le son par l’intermédiaire du récepteur. 3 Appuyer sur la touche EXIT pour quitter le menu. ➢ Lorsque le récepteur est réglé à marche, il est possible d’entendre le son du téléviseur par les deux canaux sonores (stéréo). Cela n’est pas toujours vrai. Lorsque le téléviseur émet des Dépl. Intro. Sorite signaux numériques (antenne), il peut émettre le son du canal 5.1 par la prise SPDIF. Mais si la source est, par exemple, le récepteur DVD, le téléviseur peut recevoir le son uniquement sur le canal 2 en mode HDMI. Dans ce cas, le son du canal 2 est transmis au récepteur uniquement par la prise SPDIF. Si le récepteur sert exclusivement au cinéma maison (prise en charge audio seulement), il se peut qu’il n’apparaisse pas dans la liste des appareils. Le récepteur ne fonctionne que lorsque la prise optique du téléviseur et le récepteur sont bien raccordés. En cas de problème de droits d’auteurs, l’écoute par l’intermédiaire du récepteur pourrait ne pas bien fonctionner. Lorsque le récepteur est en mode d’écoute, certaines restrictions relatives à la fonction ISI et aux fonctions audio s’appliquent. ➢ ➢ ➢ ➢ TV Air 28 Enregistrer: marche Brancher Enregistrer Configuration Liste de vérification avant de faire une demande de service Symptôme Anynet+ ne fonctionne pas. Solution Vérifier si l’appareil est bien un appareil Anynet+. Le système Anynet+ ne prend en charge que les appareils Anynet+. ■ Ne brancher qu’un seul récepteur (cinéma maison). ■ Vérifier si le cordon d’alimentation de l’appareil Anynet+ est bien branché. ■ Vérifier les branchements des câbles vidéo/audio/HDMI 1.3 de l’appareil Anynet+. ■ Vérifier si Anynet+ (HDMI-CEC) est activé dans le menu Configuration d’Anynet+. ■ Vérifier si la télécommande est en mode TV. ■ Vérifier s’il s’agit de la télécommande exclusive Anynet+. ■ Anynet+ ne fonctionne pas dans certaines conditions. (recherche de canaux) ■ Au moment du branchement ou du débranchement du câble HDMI 1.3, s’assurer d’effectuer une nouvelle recherche des appareils ou de redémarrer le téléviseur. ■ Vérifier si la fonction Anynet+ de l’appareil Anynet+ est activée. Je souhaite lancer Anynet+. ■ Vérifier si l’appareil Anynet+ est bien branché au téléviseur et vérifier si Anynet+ (HDMI-CEC) est activé dans le menu Configuration d’Anynet+. ■ Appuyer sur la touche TV de la télécommande du téléviseur pour permuter vers le téléviseur. Appuyer ensuite sur la touche Anynet+ pour afficher le menu Anynet+ et sélectionner le menu désiré. Je souhaite quitter Anynet+. ■ Sélectionner Écouter la télévision dans le menu Anynet+. ■ Appuyer sur la touche SOURCE de la télécommande du téléviseur pour sélectionner un appareil autre que les appareils Anynet+. ■ Appuyer sur les touches CH, CH LIST, PRE-CH, FAV.CH, ou autre pour passer au mode TV. (Remarque : le bouton des canaux ne fonctionne que si aucun appareil Anynet+ à syntoniseur intégré Anynet+ n’est branché.) Le message Connexion à l’ ■ La télécommande ne peut être utilisée pendant la configuration d’Anynet+ ou pour la permutation vers un mode de visionnement. appareil Anynet+... s’affiche à l’écran. ■ Utiliser la télécommande lorsque le réglage d’Anynet+ ou la permutation vers le mode de visionnement sont terminés. L’appareil Anynet+ ne lit pas. Vous ne pouvez pas utiliser la fonction lecture lorsque le mode Prêt-à-l’emploi est en cours d’exécution. L’appareil branché n’est pas ■ Vérifier si l’appareil prend en charge les fonctions Anynet+. affiché. ■ Vérifier si le câble HDMI 1.3 est bien branché. ■ Vérifier si Anynet+ (HDMI-CEC) est activé dans le menu Configuration d’Anynet+. ■ Rechercher les appareils Anynet+ à nouveau. ■ Seul le câble HDMI 1.3 permet de brancher un appareil Anynet+. Certains câbles HDMI ne prennent pas en charge des fonctions Anynet+. L’émission ne peut pas être Vérifier si la prise d’antenne sur l’appareil enregistreur est branchée correctement. enregistrée. ■ Le son du téléviseur ne sort Brancher le câble optique entre le téléviseur et le récepteur. pas par le récepteur. Français - 65 BN68-01192F-02Fre_4.indd 65 2007-02-26 ソタネト 6:05:59 Annexe Dépannage Si le téléviseur semble éprouver un problème, consulter d’abord cette liste des problèmes et solutions possibles. Si aucun de ces conseils ne permet de corriger le problème, communiquer avec le centre de service Samsung le plus près. Problème Image de mauvaise qualité. Solution possible Essayer un autre canal. Réorienter l’antenne. Vérifier toutes les branchements de câbles. Son de mauvaise qualité. Essayer un autre canal. Réorienter l’antenne. Pas d’image ni de son. Essayer un autre canal. Appuyer sur la touche SOURCE. Vérifier si le téléviseur est branché. Vérifier les branchements de l’antenne. Vérifier que la touche MUTE n’est pas enfoncée. Aucun son ou le son est trop faible au En premier lieu, vérifier le volume des appareils branchés au téléviseur (récepteur numérique, lecteur DVD, câblosélecteur, magnétoscope, etc.). Régler ensuite le volume du téléviseur en volume maximum. conséquence. Défilement vertical de l’image. Vérifier toutes les branchements de câbles. Fonctionnement anormal du Débrancher le téléviseur pendant 30 secondes, le rebrancher et le rallumer. téléviseur. Le téléviseur ne s’allume pas. Vérifier que la prise murale fonctionne. La télécommande fonctionne mal. Problème d’écran en diffusion numérique. Remplacer les piles de la télécommande. Nettoyer l’extrémité supérieure de la télécommande (hublot de transmission). Vérifier les bornes des piles. Appuyer sur la touche TV pour régler la télécommande au mode TV. Vérifier s’il y a des piles dans la télécommande. Vérifier si les bornes “ + ” et “ - ” des batteries sont insérées correctement. Vérifier la puissance du signal numérique et l’entrée de l’antenne. L’image est trop pâle ou trop foncée. Régler la luminosité et le contraste. Utiliser le réglage de précision. L’image est trop grande ou trop petite. Redimensionner l’image. La qualité visuelle des canaux La qualité visuelle des canaux numériques peut varier selon la méthode de production d’origine numériques varie. (analogue ou numérique). - Si la méthode de production d’origine est numérique : Une émission de haute qualité visuelle. - Si la méthode de production d’origine est analogue : Le programme numérique affiché à l’écran est un programme analogue à l’origine, mais converti au format numérique. La qualité visuelle est de calibre SD (définition standard). L’écran est noir et le témoin Sur l’ordinateur, Sur l’ordinateur, vérifier l’alimentation et le câble de signal. d’alimentation clignote. Le téléviseur est en mode d’économie d’énergie. Déplacer la souris de l’ordinateur ou appuyer sur une touche du clavier. Sur le matériel, vérifier le mode (STB, DVD, etc.), l’alimentation et le câble de signal. Le téléviseur est en mode d’économie d’énergie. Appuyer sur la touche Source du panneau ou de la télécommande. Éteindre le téléviseur et le rallumer. Même si le téléviseur indique HD, la L’indication HD (haute définition) affichée lors d’un changement de poste ou lorsque la touche qualité visuelle n’est pas satisfaisante. Information de la télécommande est enfoncée signifie que le canal sélectionné est un canal numérique. Si le diffuseur convertit un signal analogue au format numérique et transmet ce signal, il est possible que la qualité visuelle ne soit pas parfaite. Français - 66 BN68-01192F-02Fre_4.indd 66 2007-02-26 ソタネト 6:05:59 Comprend le jeu d’installation murale Cette installation convient à la pose du jeu d’installation murale à un mur. Lorsque le jeu d’installation doit être posé sur un autre matériau de construction, contacter le détaillant le plus près. Spécifications du jeu d’installation murale ( VESA ) Type de produit ACL-TV Plasma-TV pouces Spéc. VESA (A * B) Vis standard (C * D) Quantité 23 ~ 26 200 * 100 M4 * L10 4 32 ~ 40 200 * 200 M6 * L10 4 46 ~ 52 600 * 400 57 700 * 400 M8 * L15 4 42 ~ 50 600 * 400 63 Aucun VESA M8 6 1 Nous offrons les dimensions standard pour les jeux d’installation murale, indiquées dans le tableau ci-dessus. 2 Un manuel d’installation détaillée et toutes les pièces nécessaires à l’assemblage sont comprises avec l’achat de notre jeu d’installation murale. 3 Ne pas utiliser de vis plus longues que les dimensions standard : elles pourraient endommager l’intérieur du téléviseur. 4 Notre modèle de 63 po n’est pas conforme aux spécifications VESA Cela étant, utiliserle jeu d’installation murale spécifique à ce modèle. Français - 67 BN68-01192F-02Fre_4.indd 67 2007-02-26 ソタネト 6:05:59 Comment assembler le support(selon le modèle) À l’aide des six vis servant à immobiliser le support et l’écran, fixer fermement l’écran au support. (L’aspect extérieur de l’appareil peut être différent de celui du modèle illustré.) Dans le cas d’une installation murale du téléviseur, fixer le couvercle sur le support à l’aide des deux vis fournies. Mise en garde Fixer fermement le support au téléviseur avant de le déplacer, car le support risque de tomber et de causer des blessures sérieuses. ➢ Le téléviseur doit être transporté par au moins deux personnes. Ne jamais déposer le téléviseur sur le sol afin d’éviter d’endommager l’écran. Toujours ranger le téléviseur en position verticale. Spécifications Modèle HP-T4254 HP-T5054 Taille de l’écran (en diagonal) 42 pouces 50 pouces 1024 x 768 @ 60 Hz 1360 x 768 @ 60 Hz 10 W 15 W 41,5 x 4,1 x 27,5 pouces (1059,5 x 757 x 316 mm) 41,5 x 13,4 x 30,5 pouces (1231 x 848,5 x 316 mm) 67,6 lb (30,7 kg) 73,8 lb (33,5 kg) 91,4 lb (41,5 kg) 97 lb (44 kg) Résolution PC Son(Sortie) Dimension (L x H x P) Corps Avec support Poids Corps Avec support Environnement d’utilisation Température pour le fonctionnement Niveau d’humidité relative pour le fonctionnement Température pour l’entreposage Niveau d’humidité pour l’entreposage ➢ ➢ ➢ 50 °F à 104 °F (10 °C à 40 °C) 10 à 80 %, sans condensation (20,00) °C à 45,00 °C ((20) °C à 45 °C) 5 à 95%, sans condensation Appareil numérique de catégorie B. La conception et les spécifications sont sujettes à changement sans préavis. Pour la source d’alimentation, consulter l’étiquette apposée sur le produit. Pivotement du support (Gauche/Droite) HP-T4254/HP-T5054 Oui -20° ~ 20° Français - 68 BN68-01192F-02Fre_4.indd 68 2007-02-26 ソタネト 6:06:01 Dimensions (HP-T4254) VUE DE DESSUS VUE AVANT DIMENSION DU PANNEAU DE PRISES : 2 ¼ po H x 18 ¾ po L; 5 ¾ po À PARTIR DU BAS VUE LATÉRALE VUE ARRIÈRE REMARQUE : Tous les dessins ne sont pas nécessairement des représentations à l’échelle. Certaines dimensions peuvent avoir été changées sans avis. Mesurez les dimensions de chaque unité avant de procéder à des travaux de menuiserie. Nous n’assumons aucune responsabilité pour les erreurs typographiques ou d’impression. © 2007 Samsung Electronics America, Inc. Français - 69 BN68-01192F-02Fre_4.indd 69 2007-02-26 ソタネト 6:06:35 Dimensions (HP-T5054) VUE DE DESSUS VUE AVANT DIMENSION DU PANNEAU DE PRISES : 2 ¼ po H x 18 ¾ po L; 5 ¾ po À PARTIR DU BAS VUE LATÉRALE VUE ARRIÈRE REMARQUE : Tous les dessins ne sont pas nécessairement des représentations à l’échelle. Certaines dimensions peuvent avoir été changées sans avis. Mesurez les dimensions de chaque unité avant de procéder à des travaux de menuiserie. Nous n’assumons aucune responsabilité pour les erreurs typographiques ou d’impression. © 2007 Samsung Electronics America, Inc. Français - 70 BN68-01192F-02Fre_4.indd 70 2007-02-26 ソタネト 6:08:17 Cette page est laissée intentionnellement en blanc. BN68-01192F-02Fre_4.indd 71 2007-02-26 ソタネト 6:09:36 Cette page est laissée intentionnellement en blanc. BN68-01192F-02Fre_4.indd 71 2007-02-26 ソタネト 6:12:09 Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Communiquez avec SAMSUNG WORLD-WIDE Pour toute question ou commentaire se rapportant aux produits Samsung, veuillez communiquer avec le centre de service à la clientèle SAMSUNG. Country Customer Care Center Web Site CANADA 1-800-SAMSUNG (7267864) www.samsung.com/ca U.S.A 1-800-SAMSUNG (7267864) www.samsung.com Address Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada Samsung Electronique Canada Inc., Service à la Clientèle 55 Standish Court Mississauga, Ontario L5R 4B2 Canada Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511 BN68-01192F-02 BN68-01192F-02Fre_4.indd 72 2007-02-26 ソタネト 6:09:36
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project