Sony RDR-HX710 Operating Instructions

Sony RDR-HX710  Operating Instructions
2-629-954-11(3)
DVD Recorder
Operating Instructions
RDR-HX710/HX910
© 2005 Sony Corporation
Precautions
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to qualified
personnel only.
The power cord (mains lead) must only
be changed at a qualified service shop.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the laser
protective housing inside the
enclosure.
CAUTION
The use of optical instruments with this
product will increase eye hazard. As
the laser beam used in this DVD
recorder is harmful to eyes, do not
attempt to disassemble the cabinet.
Refer servicing to qualified personnel
only.
This label is located on the laser
protective housing inside the
enclosure.
2
• This unit operates on 220 – 240 V
AC, 50/60 Hz. Check that the unit’s
operating voltage is identical with
your local power supply.
• To prevent fire or shock hazard, do
not place objects filled with liquids,
such as vases, on the apparatus.
G-CODE is a registered trademark of
Gemstar Development Corporation.
The G-CODE system is manufactured
under license from Gemstar
Development Corporation.
Precautions
This equipment has been tested and
found to comply with the limits set
out in the EMC Directive using a
connection cable shorter than
3 metres.
On safety
Should any solid object or liquid fall
into the cabinet, unplug the recorder
and have it checked by qualified
personnel before operating it any
further.
About the hard disk drive
Disposal of Old Electrical &
Electronic Equipment
This symbol is applicable only in the
European Union and other European
countries with seperate collection
systems.
The hard disk has a high storage
density, which enables long
recording durations and quick
access to the written data. However,
it can easily be damaged by shock,
vibration or dust, and should be kept
away from magnets. To avoid losing
important data, observe the
following precautions.
• Do not apply a strong shock to the
recorder.
• Do not place the recorder in a
location subject to mechanical
vibrations or in an unstable
location.
• Do not place the recorder on top of
a hot surface, such as a VCR or
amplifier (receiver).
• Do not use the recorder in a place
subject to extreme changes in
temperature (temperature gradient
less than 10 °C/hour).
• Do not move the recorder with its
power cord (mains lead)
connected.
• Do not disconnect the power cord
(mains lead) while the power is on.
• When disconnecting the power
cord (mains lead), turn off the
power and make sure that the hard
disk drive is not operating (the
clock is displayed in the front
panel display and all recording or
dubbing has stopped).
• Do not move the recorder for one
minute after you have unplugged
the power cord (mains lead).
• Do not attempt to replace or
upgrade the hard disk by yourself,
as this may result in malfunction.
If the hard disk drive should
malfunction, you cannot recover lost
data. The hard disk drive is only a
temporary storage space.
About repairing the hard disk
drive
• The contents of the hard disk drive
may be checked in case of repair
or inspection during a malfunction
or modification. However, the
contents will not be backed up or
saved by Sony.
• If the hard disk needs to be
formatted or replaced, it will be
done at the discretion of Sony. All
contents of the hard disk drive will
be erased, including contents that
violate copyright laws.
On power sources
• The recorder is not disconnected
from the AC power source (mains)
as long as it is connected to the
wall outlet, even if the recorder
itself has been turned off.
• If you are not going to use the
recorder for a long time, be sure to
disconnect the recorder from the
wall outlet. To disconnect the AC
power cord (mains lead), grasp the
plug itself; never pull the cord.
• Before disconnecting the AC
power cord (mains lead), check
that the recorder’s hard disk is not
operating (recording or dubbing)
on the front panel display.
On placement
• Place the recorder in a location with
adequate ventilation to prevent heat
build-up in the recorder.
• Do not place the recorder on a soft
surface such as a rug that might
block the ventilation holes.
• Do not place the recorder in a
confined space such as a bookshelf
or similar unit.
• Do not place the recorder in a
location near heat sources, or in a
place subject to direct sunlight,
excessive dust, or mechanical
shock.
• Do not place the recorder in an
inclined position. It is designed to
be operated in a horizontal
position only.
• Keep the recorder and discs away
from equipment with strong
magnets, such as microwave
ovens, or large loudspeakers.
• Do not place heavy objects on the
recorder.
On recording
• Note that the contents of the
recording cannot be compensated
for under any and all conditions,
including conditions that may
arise due to a malfunction of this
unit.
• Make trial recordings before
making the actual recording.
Copyrights
• Television programmes, films,
video tapes, discs, and other
materials may be copyrighted.
Unauthorized recording of such
material may be contrary to the
provisions of the copyright laws.
Also, use of this recorder with
cable television transmission may
require authorization from the
cable television transmitter and/or
programme owner.
• This product incorporates
copyright protection technology
that is protected by U.S. patents
and other intellectual property
rights. Use of this copyright
protection technology must be
authorized by Macrovision, and is
intended for home and other
limited viewing uses only unless
otherwise authorized by
Macrovision. Reverse engineering
or disassembly is prohibited.
Copy guard function
Since the recorder has a copy guard
function, programmes received
through an external tuner (not
supplied) may contain copy
protection signals (copy guard
function) and as such may not be
recordable, depending on the type of
signal.
IMPORTANT NOTICE
Caution: This recorder is capable
of holding a still video image or
on-screen display image on your
television screen indefinitely. If
you leave the still video image or
on-screen display image
displayed on your TV for an
extended period of time you risk
permanent damage to your
television screen. Plasma display
panels and projection televisions
are especially susceptible to this.
If you have any questions or
problems concerning your recorder,
please consult your nearest Sony
dealer.
About this manual
Check your model name
The instructions in this manual
are for 2 models: RDR-HX710
and RDR-HX910. Check your
model name by looking at the
front panel of the recorder.
• In this manual, the internal hard
disk drive is written as “HDD,”
and “disc” is used as a general
reference for the HDD, DVDs, or
CDs unless otherwise specified by
the text or illustrations.
• Instructions in this manual
describe the controls on the
remote. You can also use the
controls on the recorder if they
have the same or similar names as
those on the remote.
• The on-screen display illustrations
used in this manual may not match
the graphics displayed on your TV
screen.
• The explanations regarding DVDs
in this manual refer to DVDs
created on this recorder. The
explanations do not apply to
DVDs that are created on other
recorders and played back on this
recorder.
3
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ways to Use Your DVD Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Quick Guide to Disc Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recordable and playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Hookups and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hooking Up the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Step 2: Connecting the Aerial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Step 3: Connecting the Video Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the PROGRESSIVE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Step 4: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 5: Connecting the Power Cord (Mains Lead) . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Step 6: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Controlling TVs with the remote. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Controlling the volume of your AV amplifier (receiver) with the remote . . . . . . . . . 19
If you have a Sony DVD player or more than one Sony DVD recorder . . . . . . . . . 20
Step 7: Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting a VCR or Similar Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting to the LINE IN 1 or 3 jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting to the LINE 2 IN jacks on the front panel . . . . . . . . . . . . . . . . . . . . . . 23
Connecting to a Satellite or Digital Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Seven Basic Operations — Getting to Know Your DVD Recorder
1. Inserting and Formatting a DVD Disc (Disc Info) . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Inserting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Formatting a DVD disc (Disc Info) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2. Recording a Programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Checking the disc status while recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3. Playing the Recorded Programme (Title List) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4. Displaying the Playing Time and Play Information . . . . . . . . . . . . . . . . . . . . . . . . . 31
Checking the playing/remaining time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5. Changing the Name of a Recorded Programme . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6. Labelling and Protecting a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Labelling a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Protecting a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7. Playing the Disc on Other DVD Equipment (Finalize) . . . . . . . . . . . . . . . . . . . . . . . 35
Unfinalizing a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Before Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Recording mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Recording stereo and bilingual programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Unrecordable pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Timer Recording (Standard/G-Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Setting the timer manually (Standard) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Recording TV programmes using the G-Code system . . . . . . . . . . . . . . . . . . . . . 41
Using the Quick Timer function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Adjusting the recording picture quality and size . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Creating chapters in a title. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Checking/Changing/Cancelling Timer Settings (Timer List) . . . . . . . . . . . . . . . . . . . . 44
Automatically erasing old titles (Auto Title Erase) . . . . . . . . . . . . . . . . . . . . . . . . . 45
Recording From Connected Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Recording from connected equipment with a timer (Synchro Rec) . . . . . . . . . . . . 46
Recording from connected equipment without a timer . . . . . . . . . . . . . . . . . . . . . 47
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Playback options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Adjusting the picture quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Adjusting the sound quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Pausing a TV Broadcast (TV Pause). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Playing from the beginning of the programme you are recording
(Chasing Playback) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Playing a previous recording while making another
(Simultaneous Rec and Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Searching for a Title/Chapter/Track, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Searching by Thumbnail (Visual Search) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Searching by title number or time code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Playing MP3 Audio Tracks or JPEG Image Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Selecting an MP3 album or track. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Selecting a JPEG album or image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
About MP3 audio tracks and JPEG image files. . . . . . . . . . . . . . . . . . . . . . . . . . . 60
MP3 audio tracks or JPEG image files that the recorder can play . . . . . . . . . . . . 60
About playback order of albums, tracks, and files . . . . . . . . . . . . . . . . . . . . . . . . . 61
Erasing and Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Before Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Edit options for the HDD and DVD-RWs (VR mode). . . . . . . . . . . . . . . . . . . . . . . 62
Edit options for DVD+RWs/DVD-RWs (Video mode)/DVD+Rs/DVD-Rs. . . . . . . . 63
Erasing and Editing a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Erasing a chapter (Delete Chapter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Erasing a section of a title (A-B Erase) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Erasing multiple titles (Erase Titles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Dividing a title (Divide). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Erasing all titles on the disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Erasing titles to open up disc space (Disc Map) . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Creating chapters manually. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
,continued
5
Creating and Editing a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Moving a Playlist title (Change Order) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Combining multiple Playlist titles (Combine) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Dividing a Playlist title (Divide). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Dubbing (HDD y DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Before Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
About “Dub Mode” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Dubbing a single title (Title Dub) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Dubbing multiple titles (Dub Selected Titles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
DV Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Before DV Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Preparing for DV dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Recording an Entire DV Format Tape (One Touch Dubbing) . . . . . . . . . . . . . . . . . . . 77
Program Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Aerial Reception and Language Settings (Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Channel Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Channel List (Changing/Disabling the channels) . . . . . . . . . . . . . . . . . . . . . . . . . . 83
TV Guide Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Video Settings (Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Audio Settings (Audio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Recording and Parental Control Settings (Features) . . . . . . . . . . . . . . . . . . . . . . . . . 89
Disc and Remote Control Settings/Factory Settings (Options) . . . . . . . . . . . . . . . . . . 91
Easy Setup (Resetting the Recorder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Self-diagnosis Function (When letters/numbers appear in the display) . . . . . . . . . . . 98
Notes About This Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
About i.LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
6
Ways to Use Your DVD Recorder
Recording/Playback
Compatible media and reference pages
Quick access to recorded titles
– Title List
,
Play the beginning of a title
while it is being recorded
– Chasing Playback
,
Watching one title while
recording another
– Simultaneous Rec and Play
,
Dubbing/Editing
HDD
+RW
-RWVR -RWVideo
+R
-R
“3. Playing the Recorded Programme (Title List)” on
page 28
HDD
-RWVR
“Playing from the beginning of the programme you are
recording (Chasing Playback)” on page 55
HDD
VCD
+RW
-RWVR -RWVideo
CD
DATA DVD DATA CD
+R
-R
“Playing a previous recording while making another
(Simultaneous Rec and Play)” on page 55
Compatible media and reference pages
Creating your own programme
– Playlist
,
Copying a recorded title to and
from the HDD
– Dubbing (HDD y DVD)
,
Automatic dubbing of DV tapes
– DV Dubbing
,
HDD
-RWVR
“Creating and Editing a Playlist” on page 67
HDD
+RW
-RWVR -RWVideo
+R
-R
“Dubbing (HDD y DVD)” on page 70
HDD
+RW
-RWVR -RWVideo
+R
-R
“DV Dubbing” on page 75
A list of recordable and playable discs is on page 8.
7
Quick Guide to Disc Types
Recordable and playable discs
Icon used in
this manual
Formatting
(new discs)
Compatibility with other DVD
players (finalizing)
Hard disk drive
(internal)
HDD
(Formatting
unnecessary)
Dub HDD contents to a DVD to
play on other DVD players
DVD+RW
+RW
Automatically
formatted in +VR
mode
Playable on DVD+RW
compatible players
(automatically finalized)
-RWVR
Format in VR mode
(page 25)
Playable only on VR mode
compatible players (finalization
unnecessary)
-RWVideo
Format in Video mode
(page 25)
Playable on most DVD players
(finalization necessary)
(page 35)
+R
Automatically
formatted
Playable on most DVD players
(finalization necessary)
(page 35)
-R
Automatically
formatted
Playable on most DVD players
(finalization necessary)
(page 35)
Type
Disc Logo
VR
mode
DVDRW
*2
Video
mode
DVD+R
DVD+R DL
DVD-R
Usable disc versions (as of March 2005)
• 8x-speed or slower DVD+RWs
• 6x-speed or slower DVD-RWs (Ver.1.1, Ver.1.2
with CPRM*1)
• 16x-speed or slower DVD+Rs
• 16x-speed or slower DVD-Rs (Ver.2.0, Ver.2.1)
• 2.4x-speed DVD+R DL (Double Layer) discs
8
“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD+R DL,”
and “DVD-R” are trademarks.
*1
CPRM (Content Protection for Recordable Media) is
a coding technology that protects copyrights for
images.
*2 This logo applies to 4x and 6x speed DVD-RW discs.
Recording Features
Rewrite
(page 37)
Auto
Chapter
(page 89)
Editing Features
Manual
Chapter
(page 67)
Record
16:9 sizes
(page 42)
Change
title name
(page 63)
Delete
title
(page 65)
A-B Erase
(page 64)
Playlist
(page 67)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes*3
Yes
Yes
No
No
No
Yes
No
No
Yes
Yes*4
No
No
No
Yes
No
Yes*3
Yes
Yes*4
No
No
Discs that cannot be recorded on
• 8 cm discs
• DVD-Rs in VR mode (Video Recording format)
*3
Only if the recording mode is LSP, SP, HSP, or HQ,
and “DVD Rec. Picture Size” is set to “16:9.”
*4 Erasing titles does not free up disc space.
,continued
9
Playable discs
Type
Disc Logo
Icon used
in this
manual
DVD VIDEO
DVD
Discs such as movies that can be purchased or
rented
VIDEO CD
VCD
VIDEO CDs or CD-Rs/CD-RWs in VIDEO
CD/Super VIDEO CD format
CD
Music CDs or CD-Rs/CD-RWs in music CD
format that can be purchased
CD
DATA DVD
—
DATA DVD
DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs/
DVD-ROMs containing JPEG image files
DATA CD
—
DATA CD
CD-ROMs/CD-Rs/CD-RWs containing MP3
audio tracks or JPEG image files
8 cm DVD+RW/
DVD-RW/DVD-R
—
—
“DVD VIDEO” and “CD” are trademarks.
Discs that cannot be played
• PHOTO CDs
• CD-ROMs/CD-Rs/CD-RWs that are not
recorded in music CD or Video CD format, or do
not contain MP3 or JPEG files
• Data part of CD-Extras
• DVD-ROMs that do not contain JPEG files or
are not in DVD Video format
• DVD Audio discs
• DVD-RAMs
• HD layer on Super Audio CDs
• DVD VIDEOs with a different region code
(page 11)
• DVD-Rs recorded in VR mode (Video
Recording format)
10
Characteristics
8 cm DVD+RW, DVD-RW, and DVD-R
recorded with a DVD video camera.
(Still images recorded with a DVD video
camera cannot be played.)
Maximum recordable number of titles
Disc
Number of titles*
HDD
300
DVD-RW/DVD-R
99
DVD+RW/DVD+R
49
DVD+R DL
49
* The maximum length for each title is eight hours.
Note on playback operations of DVD VIDEOs/
VIDEO CDs
Some playback operations of DVD VIDEOs/
VIDEO CDs may be intentionally set by software
producers. Since this recorder plays DVD
VIDEOs/VIDEO CDs according to the disc
contents the software producers designed, some
playback features may not be available. Also, see
the instructions supplied with the DVD VIDEOs/
VIDEO CDs.
Region code (DVD VIDEO only)
Your recorder has a region code printed on the rear
of the unit and will only play DVD VIDEOs
(playback only) labelled with identical region
codes. This system is used to protect copyrights.
DVD VIDEOs labelled ALL will also play on this
recorder.
If you try to play any other DVD VIDEO, the
message “Playback prohibited by region code.”
will appear on the TV screen. Depending on the
DVD VIDEO, no region code indication may be
labelled even though playing the DVD VIDEO is
prohibited by area restrictions.
X
RDR–XXXX
00V 00Hz
00W
NO.
0-000-000-00
Region code
Music discs encoded with copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are being
marketed by some record companies. Please be
aware that among those discs, there are some that
do not conform to the CD standard and may not be
playable by this product.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
b Notes
• Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or
CD-RWs/CD-Rs cannot be played on this recorder due
to the recording quality or physical condition of the
disc, or the characteristics of the recording device and
authoring software. The disc will not play if it has not
been correctly finalized. For more information, see the
operating instructions for the recording device.
• You cannot mix VR mode and Video mode on the same
DVD-RW. To change the disc’s format, reformat the
disc (page 25). Note that the disc’s contents will be
erased after reformatting.
• You cannot shorten the time required for recording
even with high-speed discs.
• It is recommended that you use discs with “For Video”
printed on their packaging.
• You cannot add new recordings to DVD+Rs, DVD-Rs,
or DVD-RWs (Video mode) that contain recordings
made on other DVD equipment.
• In some cases, you may not be able to add new
recordings to DVD+RWs that contain recordings made
on other DVD equipment. If you do add a new
recording, note that this recorder will rewrite the DVD
menu.
• You cannot edit recordings on DVD+RWs, DVD-RWs
(Video mode), DVD+Rs, or DVD-Rs that are made on
other DVD equipment.
• If the disc contains PC data unrecognizable by this
recorder, the data may be erased.
• You may not be able to record on some recordable
discs, depending on the disc.
11
Hookups and Settings
Hooking Up the Recorder
Follow steps 1 to 7 to hook up and adjust the settings of the recorder.
b Notes
•
•
•
•
Plug cords securely to prevent unwanted noise.
Refer to the instructions supplied with the components to be connected.
You cannot connect this recorder to a TV that does not have a video input jack.
Be sure to disconnect the power cord (mains lead) of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Audio/video cord (phono plug × 3 y phono plug × 3) (1)
• Power cord (mains lead) (1)
• Aerial cable (1)
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
12
Step 2: Connecting the Aerial Cable
Connect the aerial cable by following the steps below. Do not connect the power cord (mains lead) until
you reach “Step 5: Connecting the Power Cord (Mains Lead)” on page 17.
AERIAL
DVD recorder
DIGITAL
OUT
IN
PCM/DTS/MPEG
DOLBY DIGITAL
COAXIAL
COMPONENT
VIDEO OUT
LINE IN
R-AUDIO-L
Hookups and Settings
to AERIAL IN
Y
VIDEO
S VIDEO
1
LINE OUT
R-AUDIO-L
3
VIDEO
S VIDEO
PB/CB
PR/CR
OUT
~ AC IN
OPTICAL
AERIAL
IN
OUT
TV
to AERIAL OUT
Aerial cable (supplied)
: Signal flow
1
Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the
recorder.
2
Connect AERIAL OUT of the recorder to the aerial input of your TV, using the supplied aerial
cable.
13
Step 3: Connecting the Video Cords
Select one of the following patterns A through C, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver). This will enable you to view pictures.
A Connecting to a video input jack
You will enjoy standard quality images.
B Connecting to an S VIDEO input jack
You will enjoy high quality images.
C Connecting to component video input jacks (Y, PB/CB, PR/CR)
You will enjoy accurate colour reproduction and high quality images.
If your TV accepts progressive 525p/625p format signals, you must use this connection and press
PROGRESSIVE on the remote to send progressive video signals. For details, see “Using the
PROGRESSIVE button” on page 15.
A
S-video cord
(not supplied)
INPUT
Audio/video
cord (supplied)
VIDEO
INPUT
B
S VIDEO
L
AUDIO
(yellow)
TV, projector, or AV
amplifier (receiver)
R
TV, projector, or AV
amplifier (receiver)
to LINE OUT (VIDEO)
AERIAL
IN
to LINE OUT (S VIDEO)
DIGITAL
OUT
PCM/DTS/MPEG
DOLBY DIGITAL
COAXIAL
DVD recorder
COMPONENT
VIDEO OUT
LINE IN
R-AUDIO-L
Y
VIDEO
S VIDEO
1
LINE OUT
R-AUDIO-L
VIDEO
S VIDEO
3
PB/CB
PR/CR
~ AC IN
OUT
OPTICAL
(red)
(blue)
(green)
to COMPONENT
VIDEO OUT
C
COMPONENT
VIDEO IN
Y
(green)
PB/CB
(blue)
PR/CR
Component video cord
(not supplied)
: Signal flow
14
(red)
TV, projector, or AV
amplifier (receiver)
When playing “wide screen” images
Some recorded images may not fit your TV
screen. To change the picture size, see page 85.
If you are connecting to a VCR
b Notes
• Do not connect more than one type of video cord
between the recorder and your TV at the same time.
• You cannot use the PROGRESSIVE button with the
connections A and B.
By using the PROGRESSIVE button, you can
select the signal format in which the recorder
outputs video signals: interlace or progressive.
1
Connect the recorder using the
COMPONENT VIDEO OUT jacks (pattern
C on page 14).
2
Press the PROGRESSIVE button.
“PROGRESSIVE” appears in the front panel
display when the recorder outputs progressive
signals.
Hookups and Settings
Connect your VCR to the LINE IN jack on the
recorder (page 22).
Using the PROGRESSIVE button
Progressive
Select this when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT
VIDEO OUT jacks.
Note that the pictures will not be clear or no
picture will appear if you select progressive signal
output when either of the above conditions is not
met.
Interlace
Set to this position when:
– your TV does not accept progressive signals, or,
– your TV is connected to jacks other than the
COMPONENT VIDEO OUT jacks (LINE OUT
(VIDEO or S VIDEO)).
z Hint
When you select progressive signal output, you can finetune the signal according to the type of software you are
watching (page 86).
15
Step 4: Connecting the Audio Cords
Select one of the following patterns A or B, according to the input jack on your TV monitor, projector,
or AV amplifier (receiver). This will enable you to listen to sound.
A Connecting to audio L/R input jacks
This connection will use your TV’s or stereo amplifier’s (receiver’s) two speakers for sound. You can
enjoy the following surround effects (page 51).
• TV: Dynamic, Wide, Night
• Stereo amplifier (receiver): Standard, Night
B Connecting to a digital audio input jack
If your AV amplifier (receiver) has a Dolby*1 Digital, DTS*2, or MPEG audio decoder and a digital input
jack, use this connection. You can enjoy Dolby Digital (5.1ch), DTS (5.1ch), and MPEG audio (5.1ch)
surround effects.
(yellow)
(red)
Audio/video
cord (supplied)
A
INPUT
VIDEO
(white)
(white)
L
(red)
(yellow)*
AUDIO
R
LINE OUT
R-AUDIO-L
VIDEO
TV, projector, or AV
amplifier (receiver)
S VIDEO
to LINE OUT (R-AUDIO-L)
AERIAL
IN
DIGITAL
OUT
PCM/DTS/MPEG
DOLBY DIGITAL
COAXIAL
DVD recorder
COMPONENT
VIDEO OUT
LINE IN
R-AUDIO-L
Y
VIDEO
S VIDEO
LINE OUT
1
R-AUDIO-L
VIDEO
S VIDEO
3
PB/CB
PR/CR
OUT
~ AC IN
OPTICAL
DIGITAL
OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
to DIGITAL OUT (COAXIAL or OPTICAL)
COAXIAL
or
Coaxial digital cord (not supplied)
OPTICAL
Optical digital cord (not supplied)
[Speakers]
to optical
digital input
to coaxial
digital input
Rear (L)
Rear (R)
Front (L)
Centre
Front (R)
AV amplifier (receiver)
with a decoder
: Signal flow
* The yellow plug is used for video signals (page 14).
16
[Speakers]
Subwoofer
B
z Hint
For correct speaker location, see the operating
instructions supplied with the connected components.
Connect the supplied power cord (mains lead) to
the AC IN terminal of the recorder. Then plug the
recorder and TV power cords (mains leads) into
the mains. After you connect the power cord
(mains lead), you must wait for a short while
before operating the recorder. You can
operate the recorder once the front panel display
lights up and the recorder enters standby mode.
If you connect additional equipment to this
recorder (page 22), be sure to connect the power
cord (mains lead) after all connections are
complete.
Hookups and Settings
b Notes
• Do not connect your TV’s audio output jacks to the
LINE IN (R-AUDIO-L) jacks at the same time. This
will cause unwanted noise to come from your TV’s
speakers.
• In the connection A, do not connect the LINE IN (RAUDIO-L) and LINE OUT (R-AUDIO-L) jacks to
your TV’s audio output jacks at the same time. This
will cause unwanted noise to come from your TV’s
speakers.
• In the connection B, after you have completed the
connection, make the appropriate settings under
“Audio Connection” in “Easy Setup” (page 21).
Otherwise, no sound or a loud noise will come from
your speakers.
• With the connection B, the surround sound effects of
this recorder cannot be used.
Step 5: Connecting the
Power Cord (Mains Lead)
*1 Manufactured
under license from Dolby Laboratories.
“Dolby,” and the double-D symbol are trademarks of
Dolby Laboratories.
*2 “DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
~ AC IN
1
to AC IN
2
to mains
17
Step 6: Preparing the
Remote
You can control the recorder using the supplied
remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the
markings inside the battery compartment. When
using the remote, point it at the remote sensor
on the recorder.
Controlling TVs with the remote
You can adjust the remote’s signal to control your
TV.
If you connected the recorder to an AV amplifier
(receiver), you can use the supplied remote to
control the AV amplifier’s (receiver’s) volume.
b Notes
• Depending on the connected unit, you may not be able
to control your TV or AV amplifier (receiver) with
some or all of the buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the code
number may be reset to the default setting. Set the
appropriate code number again.
TV/DVD switch
[/1
Number
buttons, SET,
-/--
1
2
3
4
5
6
7
8
9
0
b Notes
• If the supplied remote interferes your other Sony DVD
recorder or player, change the command mode number
for this recorder (page 20).
• Use the batteries correctly to avoid possible leakage
and corrosion. Do not touch the liquid with bare hands
should leakage occur. Observe the following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
– If you do not intend to use the remote for an extended
period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid inside
the battery compartment, and insert new batteries.
• Do not expose the remote sensor (marked
on the
front panel) to strong light, such as direct sunlight or
lighting apparatus. The recorder may not respond to the
remote.
18
PROG +/–
2 +/–
t TV/VIDEO
1
2
3
Slide the TV/DVD switch to TV.
Hold down [/1.
Enter your TV’s manufacturer code (see
“Code numbers of controllable TVs”
below) using the number buttons.
4
Release [/1.
When the TV/DVD switch is set to TV, the
remote performs the following:
Operations
[/1
Turns your TV on or off
2 (volume) +/–
Adjusts the volume of
your TV
PROG +/–
Selects the programme
position on your TV
(wide mode)
Switches your TV’s
input source
Number buttons
and SET, -/--*
Selects the programme
position on your TV
* If you use the number buttons to select the TV’s
programme position, press -/-- followed by the
number buttons for two-digit numbers.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your TV.
Number buttons
1
2
3
4
5
6
7
8
9
0
2 +/–
1
2
Slide the TV/DVD switch to DVD.
3
Release [/1.
Hold down [/1, and enter the
manufacturer code (see the table below)
for your AV amplifier (receiver) using the
number buttons.
The 2 (volume) +/– buttons control the AV
amplifier’s volume.
If you want to control the TV’s volume, slide
the TV/DVD switch to TV.
Code number
Sony
01 (default)
Aiwa
01 (default)
Grundig
11
Hitachi
23, 24, 72
Loewe
06, 45
Nokia
15, 16, 69, 73
Panasonic
17, 49
Philips
06, 07, 08, 23, 45, 72
Saba
12, 13, 36, 43, 74, 75
Samsung
06, 22, 23, 71, 72
Sanyo
25
Sharp
29
Telefunken
12, 13, 36, 43, 74, 75
Thomson
12, 13, 43, 74, 75
Toshiba
38
LG
06
JVC
[/1
Switches to or from the
wide mode of a Sony
wide-screen TV
t TV/VIDEO
Manufacturer
TV/DVD switch
Hookups and Settings
Buttons
Controlling the volume of your AV
amplifier (receiver) with the
remote
33
z Hint
If you want to control the TV’s volume even when the
TV/DVD switch is set to DVD, repeat the steps above
and enter the code number 90 (default).
Code numbers of controllable AV amplifiers
(receivers)
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your AV amplifier (receiver).
Manufacturer
Code number
Sony
78, 79, 80, 91
Denon
84, 85, 86
Kenwood
92, 93
Onkyo
81, 82, 83
Pioneer
99
Sansui
87
Technics
97, 98
Yamaha
94, 95, 96
,continued
19
If you have a Sony DVD player or
more than one Sony DVD recorder
If the supplied remote interferes with your other
Sony DVD recorder or player, set the command
mode number for this recorder and the supplied
remote to one that differs from the other Sony
DVD recorder or player.
The default command mode setting for this
recorder and the supplied remote is DVD3.
3
Select “Options,” and press ENTER.
SETUP
Settings
Format DVD-RW :
VR
Video
HDD Bilingual Rec. :
Main
Audio
DVD Bilingual Rec. :
Main
Features
Dimmer :
Normal
Options
Power Save :
Off
Auto Display :
On
Command Mode :
DVD3
Easy Setup
Factory Setup
4
Select “Command Mode,” and press
ENTER.
SETUP
1
2
3
4
5
6
7
8
9
0
Settings
Format DVD-RW :
VR
Video
HDD Bilingual Rec. :
Main
Audio
DVD Bilingual Rec. :
Main
Features
Dimmer :
Options
Power Save :
Easy Setup
SYSTEM
MENU
M/m,
ENTER
O RETURN
Normal
Command Mode :
Off
DVD1
On
DVD2
DVD3
Factory Setup
DVD3
Auto Display :
5
Select the Command mode (DVD1, DVD2,
or DVD3), and press ENTER.
6
Slide the COMMAND MODE switch on the
remote so it matches the mode you
selected above.
To return to the previous step
COMMAND
MODE
switch
1
Press SYSTEM MENU.
The System Menu appears.
2
Select “SETUP,” and press ENTER.
SETUP
Settings
Channel Setting
Video
Channel List
Audio
TV Guide Page
Features
Clock
Options
Language
Easy Setup
20
Press O RETURN.
Check that the command mode switch on the
remote is set to the default setting of DVD3
before you try to change the command mode for
the recorder. If the command mode for the remote
is changed to DVD1 or DVD2, you may be
unable to operate this recorder.
Make the basic adjustments by following the onscreen instructions in “Easy Setup.”
[/1
1
2
3
4
5
6
7
8
9
Audio Connection
If you connected an AV amplifier (receiver)
using either a digital optical or coaxial cord,
select “Yes: DIGITAL OUT” and set the
digital output signal (page 88).
PROG +/–
0
3
Press ENTER when “Finish” appears.
Hookups and Settings
TV Type
If you have a wide-screen TV, select “16:9.”
If you have a standard TV, select either “4:3
Letter Box” (shrink to fit) or “4:3 Pan Scan”
(stretch to fit). This will determine how
“wide-screen” images are displayed on your
TV.
Step 7: Easy Setup
“Easy Setup” is finished.
O RETURN
1
</M/m/,,
ENTER
Turn on the recorder and switch the input
selector on your TV so that the signal from
the recorder appears on your TV screen.
To return to the previous step
Press O RETURN.
z Hints
• If your AV amplifier (receiver) has an MPEG audio
decoder, set “MPEG” to “MPEG” (page 88).
• If you want to run “Easy Setup” again, select “Easy
Setup” from “SETUP” in the System Menu (page 92).
The message about the initial settings appears.
• If this message does not appear, select “Easy
Setup” from “SETUP” in the System Menu
to run “Easy Setup” function (“Settings and
Adjustments” on page 80).
2
Press ENTER.
Follow the on-screen instructions to make the
following settings.
OSD
Select the language for the on-screen displays.
Tuner System
Select “ELSE – English,” regardless of your
area or language.
The programme position order will be set.
To set the programme positions manually, see
page 80.
Clock
Set the clock manually using </M/m/,, and
press ENTER.
21
Connecting a VCR or Similar Device
After disconnecting the recorder’s power cord (mains lead) from the mains, connect a VCR or similar
recording device to the LINE IN jacks of this recorder.
Use the DV IN jack on the front panel if the equipment has a DV output jack (i.LINK jack) (page 75).
See also the instruction manual supplied with the connected equipment.
To record on this recorder, see “Recording from connected equipment without a timer” on page 47.
Connecting to the LINE IN 1 or 3 jacks
Connect a VCR or similar recording device to the LINE IN 1 or 3 of this recorder. If the equipment has
an S-video jack, you can use an S-video cord instead of an audio/video cord.
VCR, etc.
OUTPUT
VIDEO
AUDIO
L
S VIDEO
R
Audio/video cord
(not supplied)
S-video cord
(not supplied)
LINE IN
R-AUDIO-L
VIDEO
S VIDEO
1
3
to LINE IN 1 or 3
DVD recorder
AERIAL
DIGITAL
OUT
IN
PCM/DTS/MPEG
DOLBY DIGITAL
COAXIAL
COMPONENT
VIDEO OUT
LINE IN
R-AUDIO-L
Y
VIDEO
S VIDEO
LINE OUT
1
R-AUDIO-L
VIDEO
3
S VIDEO
PB/CB
PR/CR
OUT
~ AC IN
OPTICAL
: Signal flow
b Notes
• Pictures containing copy protection signals that prohibit any copying cannot be recorded.
• If you pass the recorder signals via the VCR, you may not receive a clear image on your TV screen.
DVD recorder
VCR
TV
Be sure to connect your VCR to the DVD recorder and your TV in the order shown below. To watch video tapes,
watch the tapes through a second line input on your TV.
Line input 1
VCR
DVD recorder
TV
Line input 2
• If you disconnect the recorder’s power cord (mains lead), you will not be able to view the signals from the connected
VCR.
22
Connecting to the LINE 2 IN jacks on the front panel
Connect a VCR or similar recording device to the LINE 2 IN jacks of this recorder. If the equipment has
an S-video jack, you can use an S-video cord instead of an audio/video cord.
VCR, etc.
VIDEO
AUDIO
L
S-video cord
(not supplied)
Hookups and Settings
OUTPUT
S VIDEO
R
Audio/video cord
(not supplied)
to LINE 2 IN
DVD recorder
: Signal flow
z Hint
When the connected equipment outputs only monaural sound, connect to just the L (MONO) and VIDEO input jacks
on the front of the recorder. Do not connect the R input jack.
b Notes
• Do not connect the yellow LINE IN (VIDEO) jack when using an S-video cord.
• Do not connect the output jack of this recorder to another equipment’s input jack with the other equipment’s output
jack connected to the input jack of this recorder. Noise (feedback) may result.
• Do not connect more than one type of video cord between the recorder and your TV at the same time.
23
Connecting to a Satellite or Digital Tuner
Connect a satellite or digital tuner to this recorder using the LINE IN 1 jacks. Disconnect the recorder’s
power cord (mains lead) from the mains when connecting the tuner.
To use the Synchro-Rec function, see below.
TV
Audio/video cord
(supplied)
INPUT
VIDEO
L
AUDIO
R
LINE OUT
R-AUDIO-L
VIDEO
S VIDEO
to LINE OUT
DVD recorder
AERIAL
IN
DIGITAL
OUT
COMPONENT
VIDEO OUT
PCM/DTS/MPEG
DOLBY DIGITAL
COAXIAL
LINE IN
R-AUDIO-L
Y
VIDEO
S VIDEO
LINE OUT
1
R-AUDIO-L
VIDEO
S VIDEO
3
PB/CB
PR/CR
OUT
~ AC IN
OPTICAL
to LINE IN 1
LINE IN
R-AUDIO-L
VIDEO
S VIDEO
1
3
Satellite tuner, etc.
Audio/video cord
(not supplied)
R
: Signal flow
If you want to use the Synchro Rec function
This connection is necessary to use the SynchroRecording function. See “Recording from
connected equipment with a timer (Synchro Rec)”
on page 46.
24
VIDEO
L
AUDIO
OUTPUT
b Notes
• Synchro-Recording does not work with some tuners.
For details, see the tuner’s operating instructions.
• If you disconnect the recorder’s power cord (mains
lead), you will not be able to view the signals from the
connected tuner.
Formatting a DVD disc (Disc Info)
Seven Basic Operations
— Getting to Know Your DVD Recorder
+RW
1. Inserting and Formatting
a DVD Disc (Disc Info)
+RW
VCD
-RWVR -RWVideo
CD
+R
-R
New discs are automatically formatted when
inserted. If necessary, you can manually re-format
a DVD+RW or DVD-RW disc to make a blank
disc. For DVD-RWs, you can select a recording
format (VR mode or Video mode) according to
your needs (page 8).
DVD
DATA DVD DATA CD
Z
DVD
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
0
0
</M/m/,,
ENTER
TOOLS
1
2
Press DVD.
Press Z (open/close), and place a disc on
the disc tray.
1
Insert a disc.
See “Inserting a Disc” on page 25.
2
Seven Basic Operations — Getting to Know Your DVD Recorder
Inserting a Disc
-RWVR -RWVideo
Press TOOLS.
The TOOLS menu appears.
Close
Stop
Erase
With the recording/playing side facing down
Protect
Dubbing
3
Press Z (open/close) to close the disc
tray.
Wait until “LOAD” disappears from the front
panel display.
Unused DVDs are formatted automatically.
Options for the disc or picture
The TOOLS menu displays options
applicable to the entire disc (e.g. disc
protection), recorder (e.g. audio settings
during recording), or multiple items on a list
menu (e.g. erasing multiple titles). The
displayed options differ depending on the
situation and disc type.
,continued
25
3
Move the cursor down the TOOLS menu
until “Disc Info” is selected, and press
ENTER.
Example: When a DVD-RW (VR mode) is
inserted.
Disc Information
Close
DiscName Movie
Disc Name
Media
DVD-RW
Title no.
Original 3 / Playlist 2
Date
13.10.2005 ~ 28.10.2005
HQ : 0H30M
Remainder LSP : 1H15M
SLP : 3H00M
Format
HSP : 0H45M
LP : 1H30M
SEP : 4H00M
VR
Protect Disc
Finalize
Off
SP : 1H00M
EP : 2H00M
Erase All
Format
2. 3 / 4. 7GB
1 “Disc Name” (DVD only)
2 “Media”: Disc type
3 “Format”: Recording format type (DVDRW only)
4 “On”/“Off”: Indicates whether
protection is set (DVD-RW in VR mode
only)
5 “Title no.”: Total number of titles
6 “Date”: Dates of when the oldest and the
most recent titles were recorded (DVD
only)
7 “Continuous Rem. Time”/“Remainder”
(approximate)
• The remaining recording time in each of the
recording modes
• Disc space bar
• Remaining disc space/total disc space
8 Disc setting buttons
“Disc Name” (page 34)
“Protect Disc” (page 35)
“Finalize”/“Unfinalize” (page 35)
“Erase All” (page 66)
“Format”
Available settings differ depending on the
disc type.
4
5
Select “Format,” and press ENTER.
Select “OK,” and press ENTER.
For DVD-RWs, select “VR” or “Video,” and
press ENTER.
All contents on the disc are erased.
26
z Hints
• By reformatting, you can change the recording format
on DVD-RWs, or record again on DVD-RWs that have
been finalized.
• For DVD+RWs and DVD-RWs (Video mode), you can
check free space and title location on the disc using the
Disc Map display (page 66).
b Note
On this model, 1 GB (read “gigabyte”) is equivalent to 1
billion bytes. The larger the number, the larger the disc
space.
2. Recording a Programme
HDD
+RW
-RWVR -RWVideo
+R
-R
HDD
Press z REC.
Recording starts.
Recording stops automatically after 8 hours of
continuous recording or when the HDD or
DVD is full.
To stop recording
Press x REC STOP located beneath the remote
control cover.
Note that it may take a few seconds for recorder to
stop recording.
DVD
1
2
3
4
5
6
7
8
9
PROG +/–
0
t TV/VIDEO
DISPLAY
To pause recording
Press X REC PAUSE located beneath the remote
control cover.
To restart recording, press the button again.
To watch another TV programme while
recording
Set your TV to the TV input using the t TV/
VIDEO button (page 18).
About the Teletext function
X REC PAUSE
x REC STOP
z REC
REC MODE
1
Press HDD or DVD.
When you record to a DVD, insert a
recordable DVD (see “Inserting a Disc” on
page 25).
2
Press PROG +/– to select the programme
position or input source you want to
record.
3
Press REC MODE repeatedly to select the
recording mode.
Each time you press the button, the display on
the TV screen changes as follows:
HQ
HSP
SP
LSP
LP
SEP
SLP
EP
For more details about the recording mode,
see page 37.
Some broadcasts systems ensure a Teletext
service* in which the complete programmes and
their data (title, date, channel, recording start time
etc.) are stored day by day. When recording a
programme, the recorder automatically takes the
programme name from the Teletext pages and
stores it as the title name. For detail, see “TV
Guide Page” on page 83.
Note that the Teletext information will not appear
on your TV screen. To view the Teletext
information on your TV screen, press t TV/
VIDEO on the remote to switch the input source to
your TV (page 18).
Seven Basic Operations — Getting to Know Your DVD Recorder
This section introduces the basic operation to
record the current TV programme to the hard disk
(HDD) or to a disc (DVD). For an explanation of
how to make timer recordings, see page 37.
4
* This feature mostly likely cannot be used because it
requires a service that is provided in limited areas only.
z Hint
If you do not want to watch TV while recording, you can
turn off the TV. When using a decoder, make sure to
leave it on.
b Notes
• After pressing z REC, it may take a short while to start
recording.
• You cannot change the recording mode while
recording or during recording pause.
• If there is a power failure, the programme you are
recording may be erased.
,continued
27
Checking the disc status while
recording
You can check the recording information such as
recording time or disc type.
Press DISPLAY twice during recording.
The recording information appears.
3. Playing the Recorded
Programme (Title List)
HDD
+RW
-RWVR -RWVideo
+R
-R
To play a recorded title, select the title from the
Title List.
HDD
A Disc type/format
B Recording status
DVD
1
2
3
4
5
6
7
8
9
0
C Recording mode
TITLE LIST
D Recording time
M/m,
ENTER
Press DISPLAY to turn off the display.
TOOLS
/
m
1
M
H/X/x
Press HDD or DVD.
If you select DVD, insert a DVD (see
“Inserting a Disc” on page 25).
Playback starts automatically depending on
the disc.
2
Press TITLE LIST.
To show the extended Title List, press
TOOLS to select “Display List,” and press
ENTER.
28
Title List with Thumbnail Images (Example:
DVD-RW in VR mode)
TITLE LIST
ORIGINAL
4.3 / 4.7GB
12 Tennis
Fri 28.10. 2005 13:00
DEF
Wed 26.10. 2005 20:00 (0H30M) SEP 0.3GB
Tue 25.10. 2005 9:00
Appears when all of the titles do not fit on the
list. To view the hidden titles, press M/m.
E Title’s thumbnail picture
AAB
(0H30M) LSP 0.9GB
11 Travel
10 Mystery
D Scroll bar:
The still images for each title are displayed.
3
Select a title, and press ENTER.
9 World Sports
GHI
Wed 19.10. 2005 20:00 (1H00M) SEP 0.6GB
m
Extended Title List
TITLE LIST
TITLE LIST
12
ORIGINAL
12 Tennis
ORIGINAL
Tennis
4.3 / 4.7GB
AAB Fri
Fri 28.10. 2005 13:00
28.10
11
Travel
DEF Wed 26.10
10
Mystery
AAB Tue
9
World Sports
GHI
8
Family
DEF Mon
7
Nature
L3
Sat
15.10
6
News
GHI
Fri
14.10
5
Weather
L3
Thu
13.10
11 Travel
4.3 / 4.7GB
Close
AAB
Play LSP 0.9GB
(0H30M)
Play Beginning
DEF
SEP 0.3GB
Wed 26.10. 2005 20:00 (0H30M)
Protect
25.10
10 Mystery
Wed 19.10
Tue 25.10. 2005 9:00
17.10
9 World Sports
Erase
Dubbing
AAB
Visual Search
(1H00M)
SLP 0.8GB
Title Name
Delete Chapter GHI
SEP 0.6GB
Wed 19.10. 2005 20:00 (1H00M)
A-B Erase
Sub-menu
A Disc type:
Displays a media type, HDD or DVD.
Also displays the title type (Original or
Playlist) for DVD-RWs (VR mode).
B Disc space (remainder/total)
C Title information:
Displays the title number, title name, and
recording date. Title size is shown in the
Thumbnail title list.
z (red): Indicates that the title is currently
being recorded.
: Indicates that the title is currently being
dubbed.
: Indicates the protected title.
“NEW” (or N): Indicates that the title is newly
recorded (not played back) (HDD only).
: Indicates that the Update function is set
(HDD only) (page 39).
: Indicates titles containing “CopyOnce” copy protection signals (HDD only)
(page 72).
4
Select “Play,” and press ENTER.
Playback starts from the selected title.
To stop playback
Press x.
To scroll the list display by page (Page mode)
Seven Basic Operations — Getting to Know Your DVD Recorder
The sub-menu appears.
The sub-menu displays options applicable
only to selected item. The displayed options
differ depending on the model, situation, and
disc type.
AAB
(1H00M) SLP 0.8GB
Press
/
while the list display is turned on.
Each time you press
/
, the entire Title List
changes to the previous/next page of titles.
About the Title List for HDD/DVD-RWs (VR
mode)
You can switch the Title List to show Original or
Playlist.
While the Title List menu is turned on, press
TOOLS to select either “Original” or “Playlist,”
and press ENTER.
For details, see “Edit options for the HDD and
DVD-RWs (VR mode)” on page 62.
,continued
29
To change the title order (Sort)
While the Title List menu is turned on, press
TOOLS to select “Sort Titles.” Press M/m to select
the item, and press ENTER.
Order
Sorted
By Date
in order of when the titles were
recorded. The title that is recorded
most recently is listed at the top.
By Title
in alphabetical order.
By Number
in order of recorded title number.
Unseen Title
(HDD only)
in order of when the titles were
recorded. The title that is recorded
most recently and not played back
is listed at the top. Playlist titles
are not displayed.
To change a title thumbnail picture
(Thumbnail) (HDD/DVD-RW in VR mode only)
You can select a favourite scene for the thumbnail
picture shown in the Title List menu.
1
2
Press TITLE LIST in stop mode.
3
Select “Set Thumbnail,” and press ENTER.
The selected title starts to play in the
background.
4
While watching the playback picture, press
H, X, or m/M to select the scene you
want to set for a thumbnail picture, and press
ENTER.
The display asks for confirmation.
5
Select “OK,” and press ENTER.
The scene is set for the title’s thumbnail
picture.
Select a title whose thumbnail picture you
want to change, and press ENTER.
The sub-menu appears.
To turn off the Title List
Press TITLE LIST.
z Hints
• After recording, the first scene of the recording (the
title) is automatically set as the thumbnail picture.
• You can select “TITLE LIST” from the System Menu.
30
b Notes
• The title names may not appear for DVDs created on
other DVD recorders.
• The letters that cannot be displayed are replaced with
“*.”
• It may take a few seconds for the thumbnail pictures to
be displayed.
• After editing, the title thumbnail picture may change to
the first scene of the recording (title).
• After dubbing, the title thumbnail picture set on the
source recording is cancelled.
4. Displaying the Playing
Time and Play Information
HDD
DVD
+RW
VCD
-RWVR -RWVideo
CD
+R
C The current selected function or audio
setting (appears only temporarily)
Example: Dolby Digital 5.1 ch
Rear (L/R)
-R
DATA DVD DATA CD
1 : English DolbyDigital 3/2.1
Front (L/R) + Centre
LFE (Low Frequency
Effect)
D The current selected angle
Display 2
1
2
3
4
5
6
7
8
9
Example: When playing a DVD-RW (VR mode)
0
DISPLAY
TIME/TEXT
Press DISPLAY repeatedly.
Each time you press the button, the display
changes as follows:
Display 1 t Display 2 t Display off
The displays differ depending on the disc type or
playing status.
Display 1
Example: When playing a DVD VIDEO
A Disc type*1/format (page 8)
B Title type (only appears for Playlists)
(page 62)
C Play mode
D Recording mode (page 37)
Seven Basic Operations — Getting to Know Your DVD Recorder
You can check the playing time and remaining
time of the current title, chapter, or track. Also,
you can check the disc name recorded on the
DVD/CD.
E Playing status bar*2
F Title number (chapter number*3) (page 56)
(Shows either track number, scene number,
album number*3, or file number for CDs,
VIDEO CDs, DATA DVDs, or DATA CDs.)
Title 1
Angle3(5)
1 : English DolbyDigital 2/0
A Title number/name
(Shows either track number, track name,
scene number, or file name for CDs, VIDEO
CDs, DATA DVDs, or DATA CDs.)
B Available functions for DVD VIDEOs
(
angle/
audio/
subtitle, etc.),
or playback data for DATA DVDs and
DATA CDs
G Album name appears for CDs with CD text,
DATA DVDs or DATA CDs when you
press TIME/TEXT repeatedly.
H Playing time (remaining time*3)
*1
Displays Super VIDEO CDs as “SVCD,” DATA CDs
as “CD” and DATA DVDs as “DVD.”
*2 Does not appear with VIDEO CDs, DATA DVDs, and
DATA CDs.
*3 Displayed when you press TIME/TEXT repeatedly.
,continued
31
z Hints
• If “DTS” is set to “Off” in “Audio” setup, the DTS
track selection option will not appear on the screen
even if the disc contains DTS tracks (page 88).
• When “Auto Display” is set to “On” (default) in
“Options” setup (page 92), playback information
automatically appears when the recorder is turned on,
etc.
Example: When playing a VIDEO CD
b Note
Track playing time and the current track/index number
The letters or symbols that cannot be displayed are
replaced with “*.”
Playing time and number of the current
scene or track
Example: When playing a CD
m
Remaining time of the current track
m
Playing time of the disc
Checking the playing/remaining
time
m
Remaining time of the disc
m
CD text (when available)
You can view the playing or time information
displayed on the TV screen and the front panel
display.
Example: When playing an MP3 audio track
Press TIME/TEXT repeatedly.
Current album number
The displays differ depending on the disc type or
playing status.
Example: When viewing a JPEG image
Front panel display
Example: When playing a DVD
Current album number and total number of albums
Playing time and number of the current track
m
Current file number and total number of files in the
current album
m
Playing time and number of the current title
Remaining time of the current title
Playing time and number of the current
chapter
Remaining time of the current chapter
Example: When dubbing a DVD
Remaining time of dubbing in progress
32
b Notes
• The recorder can only display the first level of a CD’s
text, such as the disc name.
• The letters or symbols that cannot be displayed are
replaced with “*.”
• Playing time of MP3 audio tracks may not be displayed
correctly.
5. Changing the Name of a
Recorded Programme
5
The selected character appears at the top of
the display.
Example: Input Title Name
You can label a DVD, title, or programme by
entering characters. You can enter up to 64
characters for a title or disc name, but the actual
number of characters displayed in the menus such
as the Title List will vary. The steps below explain
how to change the name of the recorded
programme.
1
2
3
4
5
6
7
8
9
Input Title Name
1
6
"A"
2
Back
7
"a"
3
Clear All
8
4
Space
9
Cancel
0
Finish
5
Symbol
The type of characters will change according
to the language you select in “Easy Setup.”
Some languages allow you to enter an accent
mark.
To enter a letter with an accent mark, select an
accent followed by the letter.
Example: Select “ ` ” and then “a” to enter “à.”
To insert a space, select “Space.”
0
TITLE LIST
6
</M/m/,,
ENTER
Repeat steps 4 and 5 to enter the
remaining characters.
Input row
Input Title Name
1
2
Press TITLE LIST.
1
-
6
"A"
2
c
Back
7
"a"
Select a title, and press ENTER.
3
f
Clear All
8
Space
9
Cancel
0
Finish
4
The sub-menu appears.
3
5
Select “Title Name,” and press ENTER.
Symbol
To erase a character, move the cursor to the
right of the character at the input row. Select
“Back” and press ENTER.
To insert a character, move the cursor to the
right of the point where you want to insert the
character. Select the character and press
ENTER.
To erase all of the characters, select “Clear
All” and press ENTER.
The display for entering characters appears.
4
Seven Basic Operations — Getting to Know Your DVD Recorder
Number
buttons, SET
Press </M/m/, to select the character
you want to enter, and press ENTER.
Press </M/m/, to move the cursor to
the right of the screen and select “A”
(upper-case), “a” (lower-case), or
“Symbol,” and press ENTER.
The characters of the selected type are
displayed.
7
Select “Finish,” and press ENTER.
To cancel the setting, select “Cancel.”
,continued
33
To use the number buttons
You can also use the number buttons to enter
characters.
1
2
3
In step 5 above, press a number button
repeatedly to select a character.
Example:
Press the number 3 button once to enter “D.”
Press the number 3 button three times to enter
“F.”
6. Labelling and Protecting
a Disc
You can execute options effective for the entire
disc using the Disc Information display.
Press SET and select the next character.
Select “Finish” and press ENTER.
z Hints
• You can erase all displayed characters by pressing and
holding CLEAR for 2 seconds or more.
• You can switch between “A” (upper-case), “a” (lowercase), or “Symbol” even if you press INPUT SELECT.
1
2
3
4
5
6
7
8
9
0
</M/m/,,
ENTER
TOOLS
Labelling a disc
+RW
1
-RWVR -RWVideo
+R
-R
Insert a disc.
See “Inserting a Disc” on page 25.
2
Press TOOLS to select “Disc Info,” and
press ENTER.
Example: When the inserted disc is a DVDRW (VR mode).
Disc Information
Close
DiscName
Disc Name
Media
DVD-RW
Title no.
Original 3 / Playlist 2
Date
13.10.2005 ~ 28.10.2005
HQ : 0H30M
Remainder LSP : 1H15M
SLP : 3H00M
Format
HSP : 0H45M
LP : 1H30M
SEP : 4H00M
VR
Protect Disc
Finalize
Off
SP : 1H00M
EP : 2H00M
Erase All
Format
2. 3 / 4. 7GB
3
Select “Disc Name,” and press ENTER.
Enter the disc name in the “Input Disc Name”
display (page 33).
34
b Note
You can enter up to 64 characters for a DVD’s disc name.
The disc name may not appear when the disc is played on
other DVD equipment.
Protecting a disc
+RW
-RWVR
Insert a disc.
See “Inserting a Disc” on page 25.
2
Press TOOLS to select “Disc Info,” and
press ENTER.
Disc Information
Close
DiscName
-RWVR -RWVideo
+R
-R
Finalizing is necessary when you play discs
recorded with this recorder on other DVD
equipment.
When you finalize a DVD+RW, DVD-RW
(Video mode), DVD+R, or DVD-R, a DVD menu
will be automatically created, which can be
displayed on other DVD equipment.
Before finalizing, check the differences between
the disc types in the table below.
Disc Name
Media
DVD-RW
Title no.
Original 3 / Playlist 2
Date
13.10.2005 ~ 28.10.2005
HQ : 0H30M
Remainder LSP : 1H15M
SLP : 3H00M
Format
HSP : 0H45M
LP : 1H30M
SEP : 4H00M
VR
Protect Disc
Finalize
Off
SP : 1H00M
EP : 2H00M
Erase All
Differences between the disc types
+RW
Discs are automatically finalized when
removed from the recorder. However,
you may need to finalize the disc for
certain DVD equipment, or if the
recording time is short. You can edit or
record on the disc even after finalizing.
-RWVR
Finalizing is unnecessary when playing
a disc on VR format compatible
equipment.
Even if your other DVD equipment is
VR format compatible, you may need to
finalize the disc, especially if the
recording time is short. You can edit or
record on the disc even after finalizing.
-RWVideo
Finalizing is necessary when playing on
any equipment other than this recorder.
After finalizing, you cannot edit or
record on the disc. If you want to record
on it again, unfinalize or reformat the
disc (page 25). However, if you reformat
the disc, all recorded contents will be
erased.
+R
Finalizing is necessary when playing on
any equipment other than this recorder.
After finalizing, you cannot edit or
record on the disc.
Format
2. 3 / 4. 7GB
3
4
Select “Protect Disc,” and press ENTER.
Select “Protect,” and press ENTER.
To cancel the protection
Select “Don’t Protect” in step 4.
z Hint
You can set protection for individual titles (page 63).
-R
,continued
Seven Basic Operations — Getting to Know Your DVD Recorder
1
7. Playing the Disc on Other
DVD Equipment (Finalize)
35
Unfinalizing a disc
-RWVR -RWVideo
1
2
3
4
5
6
7
8
9
For DVD-RWs (Video mode)
DVD-RW (Video mode) that have been finalized
to prohibit additional recording or editing can be
unfinalized to allow further recording or editing.
0
For DVD-RWs (VR mode)
</M/m/,,
ENTER
TOOLS
1
b Note
The recorder is not able to unfinalize DVD-RWs (Video
mode) that have been finalized on another recorder.
Insert a disc.
See “Inserting a Disc” on page 25.
2
Press TOOLS to select “Disc Info,” and
press ENTER.
The “Disc Information” display appears.
3
Finalize
About xx min is needed for finalizing this disc.
Cannot cancel finalizing during transaction.
Do you want to finalize?
OK
Cancel
Select “OK,” and press ENTER.
The recorder starts finalizing the disc.
z Hint
You can check whether the disc has been finalized or not.
If you cannot select “Finalize” in step 3 above, the disc
has already been finalized.
b Notes
• Depending on the condition of the disc, recording, or
the DVD equipment, discs may not play even if the
discs are finalized.
• The recorder may not be able to finalize the disc if it
was recorded on another recorder.
36
1
Insert a disc.
See “Inserting a Disc” on page 25.
2
Select “Finalize,” and press ENTER.
The display shows the approximate time
required for finalizing and asks for
confirmation.
4
If you cannot record or edit on a DVD-RW (VR
mode) that has been finalized with other DVD
equipment, “This disc was finalized. Unfinalize
it.” may appear.
Press TOOLS to select “Disc Info,” and
press ENTER.
The “Disc Information” display appears.
3
Select “Unfinalize,” and press ENTER.
The recorder starts unfinalizing the disc.
Unfinalizing may take several minutes.
Timer Recording
Recording
mode
z Hint
Timer recordings will be made regardless whether or not
the recorder is turned on. You can turn off the recorder
without affecting the recording even after recording
starts.
b Note
To play a recorded disc on other DVD equipment,
finalize the disc (page 35).
Recording mode
Like the SP or LP recording mode of VCRs, this
recorder has eight different recording modes.
Select a recording mode according to the time and
picture quality you need. For example, if picture
quality is your top priority, select the High Quality
mode (HQ). If recording time is your priority,
Super Extended Play mode (SEP) can be a
possible choice. Note that recording times in the
following table are approximate and the actual
times may differ. Note also that the maximum
continuous recording time for a single title is eight
hours. Contents beyond this time will not be
recorded.
Press REC MODE repeatedly to switch the
recording modes.
DVD*
HQ
(High quality)
HSP
R
SP
(Standard mode)
33
53
1
51
81
1 hr.
30 min.
67
107
2
LSP
r
85
135
2 hr.
30 min.
LP
r
103
164
3
EP
r
137
217
4
SLP
r
204
325
6
269
428
8
SEP
(Long duration)
Timer Recording
• This recorder can record on various discs. Select
the disc type according to your needs (page 8).
• Check that the disc has enough available space
for the recording (page 25). For HDD,
DVD+RWs, and DVD-RWs, you can free up
disc space by erasing titles (page 66).
• Adjust the recording picture quality and picture
size if necessary (page 42).
HDD
RDRRDRHX710 HX910
Before Recording
Before you start recording…
Recording time (hours)
* The recording time for DVD+R DL (Double Layer)
discs is as follows:
HQ: 1 hour 48 minutes
HSP: 2 hours 42 minutes
SP: 3 hours 37 minutes
LSP: 4 hours 31 minutes
LP: 5 hours 25 minutes
EP: 7 hours 14 minutes
SLP: 10 hours 51 minutes
SEP: 14 hours 28 minutes
“HQ+” recording mode
“HQ+” records pictures in higher quality than HQ
on the HDD. Set “HQ Setting” in “Features” setup
to “HQ+” (page 90). Maximum recording time is
21 hours for RDR-HX710 or 34 hours for RDRHX910. “HQ” appears in the display.
b Note
Situations below may cause slight inaccuracies with the
recording time.
– Recording a programme with poor reception, or a
programme or video source of low picture quality
– Recording on a disc that has already been edited
– Recording only a still picture or just sound
,continued
37
Recording stereo and bilingual
programmes
The recorder automatically receives and records
stereo and bilingual programmes based on the
ZWEITON system or the NICAM system.
The HDD and a DVD-RW (VR mode) can record
both main and sub sounds. You can switch
between main and sub when playing the disc. For
the HDD, you can select the sound track before
recording. Select “Main,” “Sub,” or “Main+Sub”
in “HDD Bilingual Rec.” of “Options” setup
(page 91).
A DVD+RW, DVD-RW (Video mode), DVD+R,
or DVD-R can record only one sound track (main
or sub) at a time. Select the sound track using the
Setup Display before recording starts. Set “DVD
Bilingual Rec.” to “Main” (default) or “Sub” in
“Options” setup (page 91).
ZWEITON (German stereo) system
When a stereo based programme is received,
“Stereo” appears.
When a bilingual ZWEITON based programme is
received, “Main,” “Sub,” or “Main/Sub” appears.
NICAM system
When a stereo or bilingual NICAM based
programme is received, “NICAM” appears in the
front panel display.
To record a NICAM programme, be sure to set
“Audio” of “Channel Setting” in “Settings” setup
to “NICAM” (default). If the sound is not clear
when listening to NICAM broadcasts, set “Audio”
to “Standard” (see “Channel Setting” on page 80).
z Hint
You can select the audio (main or sub) while recording
bilingual programmes using the
(audio) button.
This does not affect the recorded sound.
38
Unrecordable pictures
Pictures with copy protection cannot be recorded
on this recorder.
When the recorder receives a copy guard signal,
the recorder continues to record but only a blank,
grey coloured screen will be recorded.
Copy control
signals
Copy-Free
Copy-Once
Recordable discs
HDD
+RW
-RWVR
-RWVideo
+R
-R
HDD
-RWVR (CPRM*)
Copy-Never
None (a blank screen is
recorded)
* The recorded disc can be played only on CPRM
compatible equipment (page 8).
Timer Recording (Standard/
G-Code)
HDD
+RW
-RWVR -RWVideo
+R
2
3
4
5
6
7
8
9
OK
0
[TIMER]
</M/m/,,
ENTER
TOOLS
x REC STOP
Cancel
Set the timer manually.
Date
Start
Stop
Today
:
:
G-Code
Prog.
Media Mode
Details
Update Off
• If the “Timer – G-Code” display appears,
press < to switch the display to
“Standard”.
2
Select an item using </, and adjust
using M/m.
Timer Recording
Setting the timer manually
(Standard)
Press [TIMER].
Timer - Standard
-R
You can set the timer for a total of 30 programmes,
up to one month in advance.
There are two methods to set the timer: the
standard method and G-Code method.
• Standard: Set the date, time, and programme
position of the programme manually.
• G-Code: Enter the G-Code number designated
for each TV programme (page 41). Note that this
function may not be available in some areas.
1
1
“Date”: Sets the date.
The item changes as follows:
Today y Tomorrow y …… y Thu
28.10 (1 month later) y Sun (every Sunday)
y …… y Sat (every Saturday) y
Mon-Fri (Monday to Friday) y Mon-Sat
(Monday to Saturday) y Sun-Sat (Sunday to
Saturday) y Today
“Start”: Sets the start time.
“Stop”: Sets the stop time.
“Prog.”: Selects the programme position or
input source.
“Media”: Selects the media, HDD or DVD.
“Mode”: Selects the recording mode
(page 37).
• If you want to change the setting for the
Update function, select “Details” and press
ENTER. Select an item using </, and set
using M/m.
“Update” (HDD only): Automatically records
over a previously recorded program that is set
to be recorded daily or weekly.
To return to the Timer programming menu,
select “Previous” and ENTER.
• If you make a mistake, select the item and
change the setting.
,continued
39
3
Select “OK,” and press ENTER.
The Timer List (page 44) appears. The
TIMER REC indicator lights up on the front
panel and the recorder is ready to start
recording.
Unlike a VCR, there is no need to turn off the
recorder before the timer recording starts.
To extend the recording duration time while
recording
1
Press TOOLS during recording to select
“Extend Rec,” and press ENTER.
Extend Rec. Time
OK
Set the timer extend function.
Cancel
Wed 28.9 10:00-11:30 AAB
DVD SP
Extend Time
To stop recording during timer recording
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
Rec Mode Adjust
If there is not enough available disc space for the
recording, the recorder automatically adjusts the
recording mode to enable the entire programme to
be recorded. This function is normally set to “On.”
To cancel this function, press TOOLS while the
Timer List is displayed. Select “Rec Mode
Adjust” and press ENTER. Select “Off” and press
ENTER.
If the timer settings overlap
Overlapped timer settings are shown as follows.
Timer
These timer settings overlap. Do you want to continue?
Wed 29.10 21:00-22:00 AAB DVD SP
Wed 29.10 20:30-22:00 DEF DVD SP
OK
Cancel
To store the setting as shown, select “OK.” The
programme that starts first has priority and the
second programme starts recording only after the
first programme has finished.
To cancel the overlapped setting, select “Cancel.”
To confirm, change, or cancel timer recording
See “Checking/Changing/Cancelling Timer
Settings (Timer List)” on page 44.
40
Off
2
Press M/m to select the duration time.
You can set the duration in increments of 10
minutes, for a maximum of 60 minutes.
3
Select “OK” and press ENTER.
z Hint
You can play the recorded programme by selecting the
programme title in the Title List.
b Notes
• If a message indicating that the disc is full appears on
the screen, change the disc, or make available space for
the recording (HDD/DVD+RW/DVD-RW only)
(page 65).
• Check that the clock is correctly set before setting the
timer recording. If not, the timer recording cannot be
made.
To record a satellite programme, turn on the satellite
tuner and select the satellite programme you want to
record. Leave the satellite tuner turned on until the
recorder finishes recording. If you connect equipment
with a timer function, you can use the Synchro Rec
function (page 46).
• Even if the timer is set for the same daily or weekly
programme, the timer recording cannot be made if it
overlaps with a programme that has priority. “
” will
appear next to the overlapped setting in the Timer List.
Check the priority order of the settings.
• Even if the timer is set, timer recordings cannot be
made while recording a programme that has priority.
• The Rec Mode Adjust function only works with a timer
recording. It does not function with Quick Timer or
Synchro Rec. In addition, the Rec Mode Adjust
function does not work when recording to the HDD
while “Auto Title Erase” is set to “On.”
Recording TV programmes using
the G-Code system
3
Select “OK,” and press ENTER.
The date, start and stop times, programme
position, recording mode, etc. setting appear.
Timer - G-Code
The G-Code system is a feature that simplifies
setting the timer. Just enter the G-Code number
listed in the TV programme guide. The date, time,
and programme position of that programme are set
automatically. Note that this function may not be
available in some areas.
Check that the programme positions are correctly
set in “Channel Setting” in “Settings” setup
(page 80).
1
2
3
4
5
6
7
8
9
CLEAR
Wed 28.9
21 : 00
22 : 00
AAB
HDD
SP
Update:
Off
Cancel
Details
Change
• If you want to change the setting, press </
, to select the item and press M/m to
change the setting. For the Update function,
select “Details,” and change the settings
(page 39).
Timer Recording
Number
buttons, SET
OK
Is the following timer setting correct? To modify,
adjust each item or re-enter the timer code.
Start
Stop
Date
Prog. Media Mode
To re-enter the G-Code number, select
“Change.”
0
4
[TIMER]
</M/m/,,
ENTER
Select “OK,” and press ENTER.
The TIMER REC indicator lights up on the
front panel, and the recorder is ready to start
recording.
To stop recording during timer recording
z REC
x REC STOP
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
If the timer settings overlap
See page 40.
1
To extend the recording duration time while
recording
Press [TIMER].
See page 40.
Timer - G-Code
Set the timer by entering the timer code.
G-Code No.
OK
Cancel
To confirm, change, or cancel timer recording
See “Checking/Changing/Cancelling Timer
Settings (Timer List)” on page 44.
Standard
• If the “Timer – Standard” display appears,
press < to switch the display to “G-Code.”
2
z Hint
The Rec Mode Adjust function also works with this timer
method (page 40).
Press the number buttons to enter the
G-Code number, and press SET.
• If you make a mistake, press CLEAR and reenter the correct number.
,continued
41
Using the Quick Timer function
You can set the recorder to record in 30-minute
increments.
Press z REC repeatedly to set the duration.
Adjusting the recording picture
quality and size
You can adjust the recording picture quality and
picture size.
Each press advances the time in 30-minute
increments. The maximum duration is six hours.
0:30
1:00
5:30
6:00
(normal recording)
The time counter decreases minute by minute to
0:00, then the recorder stops recording (power
does not turn off). Even if you turn off the recorder
during recording, the recorder continues to record
until the time counter runs out.
1
2
3
4
5
6
7
8
9
0
</M/m/,,
ENTER
To cancel the Quick Timer
Press z REC repeatedly until the counter appears
in the front panel display. The recorder returns to
normal recording mode.
TOOLS
1
Before recording starts, press TOOLS to
select “Rec Settings,” and press ENTER.
Rec. Settings
Select the item you want to change.
Rec Mode :
SP
HDD Rec. Picture Size:
4:3
DVD Rec. Picture Size:
4:3
Rec NR :
2
Rec Video Equalizer
2
Select the item you want to adjust, and
press ENTER.
The adjustment display appears.
Example: Rec NR
Rec NR
Off
1
2
3
“Rec Mode”: Selects the recording mode for
the desired recording time and picture quality.
For more information, see “Recording mode”
on page 37.
42
“HDD Rec. Picture Size”/“DVD Rec. Picture
Size”: Sets the picture size of the programme
to be recorded.
• 4:3 (default): Sets the picture size to 4:3.
• 16:9: Sets the picture size to 16:9 (wide
mode).
• Auto (HDD only): Automatically selects the
actual picture size.
“Rec NR” (noise reduction): Reduces noise
contained in the video signal.
• If one programme contains two picture sizes, the
selected size is recorded. However, if the 16:9 signal
cannot be recorded as 16:9, it is recorded as 4:3.
• Remnants of images may appear on your screen when
using “Rec NR.”
• “Rec Video Equalizer” does not affect the input of the
DV IN jack and COMPONENT VIDEO IN jacks.
Creating chapters in a title
The recorder can automatically divide a recording
(a title) into chapters by inserting chapter marks
during recording. To disable this function, set
“Auto Chapter” in “Features” setup to “Off”
(page 89).
Timer Recording
“DVD Rec. Picture Size” works with DVDRs and DVD-RWs (Video mode) when the
recording mode is set to HQ, HSP, SP, or LSP.
For all other recording modes, the screen size
is fixed at “4:3.”
For DVD-RWs (VR mode), the actual picture
size is recorded regardless of the setting. For
example, if a 16:9 size picture is received, the
disc records the picture as 16:9 even if “DVD
Rec. Picture Size” is set to “4:3.”
For DVD+RWs/DVD+Rs, the screen size is
fixed at “4:3.”
b Notes
When recording on the HDD or a DVD-RW (VR
mode)
The recorder detects changes in the picture and
sound and automatically inserts chapter marks.
You can also insert and erase chapter marks
manually (page 67).
When recording on other recordable discs
“Rec Video Equalizer”: Adjusts the picture in
greater detail.
Press M/m to select the item you want to
adjust, then press ENTER.
• Contrast: Changes the contrast.
• Brightness: Changes the overall brightness.
• Colour: Makes the colours deeper or lighter.
3
Chapter marks are inserted at approximately 6minute intervals during recording.
b Note
When dubbing (page 70), the chapter marks in the
dubbing source are not retained in the dubbed title.
Adjust the setting using </M/m/,, and
press ENTER.
The default setting is underlined.
“Rec NR”: (weak) Off 1 ~ 2 ~ 3 (strong)
“Rec Video Equalizer”:
• Contrast: (weak) –3 ~ 0 ~ 3 (strong)
• Brightness: (dark) –3 ~ 0 ~ 3 (bright)
• Colour: (light) –3 ~ 0 ~ 3 (deep)
Repeat steps 2 and 3 to adjust any other items.
43
: Indicates the setting being recorded on
the HDD.
: Indicates the setting being recorded on a
DVD.
: Indicates that the Update function is set.
Checking/Changing/
Cancelling Timer Settings
(Timer List)
HDD
+RW
-RWVR -RW
+RVideo
+R
When all of the timer settings do not fit on the
list, scroll bar appears.
To view the hidden timer settings, press M/m.
-R
You can check, change, or cancel timer settings
using the Timer List.
2
Select the timer setting you want to check/
change/cancel, and press ENTER.
The sub-menu appears.
3
1
2
3
4
5
6
7
8
9
0
TIMER LIST
</M/m/,,
ENTER
O RETURN
TOOLS
Select one of the options, and press
ENTER.
“Modify”: Changes the timer setting.
Select an item using </, and adjust using
M/m. Select “OK,” and press ENTER. For the
Update function, select “Details,” and change
the settings (page 39).
Modify
OK
Cancel
Modify the timer setting.
/
1
Date
Start
Stop
Mon-Sat
22 : 00
22 : 15
AAB
HDD
SP
Update:
Off
Details
Press TIMER LIST.
“Erase”: Erases the timer setting. Select
“OK,” and press ENTER.
The Timer List appears.
10:30
TIMER LIST
Mon-Sat
22:00-22:15 AAB
Erase
SP
Fri
29.10 20:30-21:30 DEF
SP
Fri
29.10 21:00-22:00 GHI
SLP
Sat 30.10 16:00-17:00 DEF
SLP
Are you sure you want to erase this timer setting?
Mon-Sat 22:00-22:15
HDD SP
OK
Timer information displays the recording
date, time, recording mode, etc.
: Indicates that the setting is overlapped by
another setting.
(green): Indicates the setting can be
recorded.
z (red): Indicates the setting currently being
recorded.
a (grey): Indicates that the setting cannot be
recorded in the selected recording mode.
44
Prog. Media Mode
AAB
Cancel
“Check Overlap”: Checks for overlapped
settings.
Check Overlap
These timer settings overlap.
Fri
29.10
20:30-21:30
DEF
DVD SP
Fri
29.10
21:00-22:00
GHI
DVD SLP
To scroll the list display by page (Page mode)
Press
/
while the list display is turned on.
/
, the entire Timer
Each time you press
List changes to the previous/next page of timer
settings.
To turn off the Timer List
Press TIMER LIST or O RETURN.
Select “Close” to return to the Timer List.
To change or cancel the setting, repeat steps 2
and 3 above.
When the timer settings overlap
The programme that starts first has priority and the
second programme starts recording only after the
first programme has finished.
7:00
8:00
9:00
10:00
z Hint
While recording, you cannot modify the timer setting for
the current recording, but you can extend the recording
duration of the recording time (page 40).
b Notes
• Even if the timer is set, timer recordings cannot be
made while recording a programme that has priority.
• Even if the timer is set for the same daily or weekly
programme, the timer recording cannot be made if it
overlaps with a programme that has priority. “
” will
appear next to the overlapped setting in the Timer List.
Check the priority order of the settings.
Timer Recording
Close
A
will be cut off
B
When the recordings start at the same time
The programme that is set last has priority. In this
example, timer setting B is set after A, so the first
part of timer setting A will not be recorded.
7:00
8:00
9:00
10:00
A
B
When the end time of one recording and the
start time of another are the same
After finishing the previous recording, the other
recording may be delayed.
7:00
9:00
10:00
A
Automatically erasing old titles
(Auto Title Erase)
HDD
If there is not enough space for a timer recording,
the recorder automatically erases old titles
recorded on the HDD. The oldest, played title is
erased. The protected titles are not erased.
1
Press TIMER LIST.
The Timer List appears.
2
Press TOOLS to select “Auto Title Erase,”
and press ENTER.
3
Select “On,” and press ENTER.
The default setting is “Off.”
B
45
Recording From Connected
Equipment
HDD
+RW
-RWVR -RW
+RVideo
HDD
+R
-R
DVD
1
2
3
4
5
6
7
8
9
0
INPUT SELECT
Recording from connected
equipment with a timer (Synchro
Rec)
You can set the recorder to automatically record
programmes from connected equipment that has a
timer function (such as a satellite tuner). Connect
the equipment to the LINE IN 1 jacks of the
recorder (page 24).
When the connected equipment turns on, the
recorder starts recording a programme from the
LINE IN 1 jacks.
1
Before recording, select HDD or DVD.
If you select DVD, insert a recordable DVD
(see “Inserting a Disc” on page 25).
</M/m/,,
ENTER
2
Set “Synchro Rec” in “Features” setup to
“Record to HDD” or “Record to DVD”
(page 90).
3
Press INPUT SELECT repeatedly to select
“L1.”
4
Select the line input audio when recording
a bilingual programme on the HDD or DVDRWs (VR mode).
TOOLS
REC MODE
X REC PAUSE
x REC STOP
SYNCHRO
REC
Press TOOLS to select “Line Audio Input,”
and press ENTER. Then select “Bilingual,”
and press ENTER.
For details about bilingual recording, see
page 38.
5
Press REC MODE repeatedly to select the
recording mode.
For details about the recording mode, see
page 37.
6
46
Set the timer on the connected equipment
to the time of the programme you want to
record, and turn it off.
7
Press SYNCHRO REC.
The SYNCHRO REC indicator lights up on
the front panel. The recorder is ready to start
Synchro-Recording.
The recorder automatically starts recording
when it receives an input signal from the
connected equipment. The recorder stops
recording when the connected equipment
turns off.
If the timer settings of a Synchro-Recording
and another timer recording overlap
Regardless of whether or not the programme is a
Synchro Rec programme, the programme that
starts first has priority and the second programme
starts recording only after the first programme has
finished.
7:00
8:00
9:00
10:00
To stop recording
Press x REC STOP or SYNCHRO REC.
Second
programme
will be cut off
To cancel Synchro Rec
Press SYNCHRO REC.
The SYNCHRO REC indicator on the recorder
turns off.
b Notes
• The recorder starts recording only after detecting the
video signal from the connected equipment. The
beginning of the programme may not be recorded
regardless of whether or not the recorder’s power is on
or off.
• During Synchro-Recording, other operations such as
normal recording cannot be done.
• To use the connected equipment while the recorder is
standing by for Synchro-Recording, cancel SynchroRecording by pressing SYNCHRO REC. Be sure to
turn off the connected equipment and press
SYNCHRO REC to reset Synchro-Recording before
the timer recording starts.
• The Synchro Rec function does not work with some
tuners. For details, see the tuner’s operating
instructions.
• To use the Synchro Rec function, you must first set the
recorder’s clock correctly.
Timer Recording
First
programme
Recording from connected
equipment without a timer
You can record from a connected VCR or similar
device. To connect a VCR or similar device, see
“Connecting a VCR or Similar Device” on
page 22. Use the DV IN jack on the front panel if
the equipment has a DV output jack (i.LINK jack).
1
Press HDD or DVD.
If you select DVD, insert a recordable DVD
(see “Inserting a Disc” on page 25).
2
Press INPUT SELECT to select an input
source according to the connection you
made.
The front panel display changes as follows:
Programme position
3
L1
L2
L3
DV
Select the line input audio when recording
a bilingual programme on the HDD or DVDRWs (VR mode).
Press TOOLS to select “Line Audio Input,”
and press ENTER. Then select “Bilingual,”
and press ENTER.
For details about bilingual recording, see
page 38.
,continued
47
4
Press REC MODE repeatedly to select the
recording mode.
For details about the recording mode, see
page 37.
5
Press X REC PAUSE to set this recorder to
record pause.
6
Insert the source tape into the connected
equipment and set to playback pause.
7
At the same time, press X REC PAUSE on
this recorder and the pause or play button
on the connected equipment.
Recording starts.
To stop recording, press x REC STOP on this
recorder.
If you connect a digital video camera with a DV
IN jack
See “DV Dubbing” on page 75 for an explanation
of how to record from the DV IN jack.
z Hint
You can adjust the settings for the recording picture
before recording. See “Adjusting the recording picture
quality and size” on page 42.
b Notes
• When recording a video game image, the screen may
not be clear.
• Any programme that contains a Copy-Never copy
guard signal cannot be recorded. The recorder
continues to record, but a blank screen will be recorded.
48
1
• If you select DVD, insert a disc (see
“Inserting a Disc” on page 25).
• If you insert a DVD VIDEO, VIDEO CD, or
CD, press H. Playback starts.
Playback
Playing
HDD
DVD
+RW
VCD
Press HDD or DVD.
2
-RWVR -RWVideo
CD
+R
-R
For details about the Title List, see “3. Playing
the Recorded Programme (Title List)” on
page 28.
Example: DVD-RW (VR mode)
DATA DVD DATA CD
TITLE LIST
1
2
3
4
5
6
7
8
9
0
ORIGINAL
DVD
12 Tennis
PROG +/–
11 Travel
Fri 28.10. 2005 13:00
Playback
Z
HDD
Press TITLE LIST.
4.3 / 4.7GB
AAB
(0H30M) LSP 0.9GB
DEF
Wed 26.10. 2005 20:00 (0H30M) SEP 0.3GB
INPUT
SELECT
10 Mystery
Tue 25.10. 2005 9:00
AAB
(1H00M) SLP 0.8GB
9 World Sports
GHI
Wed 19.10. 2005 20:00 (1H00M) SEP 0.6GB
SUR
TITLE LIST
TOP MENU
MENU
</M/m/,,
ENTER
TOOLS
3
Select the title, and press ENTER.
The sub-menu appears.
4
Select “Play,” and press ENTER.
Playback starts from the selected title.
To use the DVD’s Menu
When you play a DVD VIDEO, or a finalized
DVD+RW, DVD-RW (Video mode), DVD+R, or
DVD-R, you can display the disc’s menu by
pressing TOP MENU or MENU.
PROGRESSIVE
To play VIDEO CDs with PBC functions
>
/
.
H/X/x
PBC (Playback Control) allows you to play
VIDEO CDs interactively using the menu on your
TV screen.
When you start playing a VIDEO CD with PBC
functions, the menu appears.
Select an item using the number buttons and press
ENTER. Then, follow the instructions in the menu
(press H when “Press SELECT” appears).
The PBC function of Super VIDEO CDs does not
work with this recorder. Super VIDEO CDs are
played in continuous play mode only.
To stop playback
Press x.
,continued
49
To playback quickly with sound (Scan Audio)
To lock the disc tray (Child Lock)
When you press M during playback of a title
recorded in the HDD, you can play quickly with
dialogue or sound (“x1.5” appears).
No sound is output when you press M two or
more times to change search speed.
You can lock the disc tray to prevent children from
ejecting the disc.
When the recorder is turned on, hold down x until
“LOCKED” appears in the front panel display.
The Z (open/close) button does not work while
the Child Lock is set.
To resume playback from the point where you
stopped (Resume Play)
When you press H again after you stop
playback, the recorder resumes playback from the
point where you pressed x.
To start from the beginning, press TOOLS to
select “Play Beginning,” and press ENTER.
Playback starts from the beginning of the title/
track/scene.
The point where you stopped playing is cleared
when:
– you open the disc tray (except for HDD).
– you play another title (except for HDD).
– you switch the Title List menu to Original or
Playlist (HDD/DVD-RW in VR mode only).
– you edit the title after stopping playback.
– you change the settings on the recorder.
– you turn off the recorder (VIDEO CD/CD/
DATA DVD/DATA CD only).
– you make a recording (except for HDD/DVDRWs in VR mode).
– you switch between JPEG and MP3.
b Note
You cannot resume playback during TV Pause.
To play restricted DVDs (Parental Control)
If you play a restricted DVD, the message “Do
you want temporarily change parental control to
*?” appears on your TV screen.
1
Select “OK” and press ENTER.
The display for entering your password
appears.
2
Enter your four-digit password using the
number buttons.
3
Press ENTER to select “OK.”
The recorder starts playback.
To register or change the password, see “Parental
Control (DVD VIDEO only)” on page 89.
50
To unlock the disc tray, hold down x until
“UNLOCKED” appears in the front panel display
when the recorder is turned on.
z Hints
• You can also use the H button in step 3 (page 49) to
start playback.
• Even if you select “Factory Setup” in “Options” setup
(page 92), the Child Lock remains set.
Playback options
To check the position of the buttons below, see the illustration on page 49.
Buttons
Operations
(audio)
HDD -RWVR
VCD
Selects one of the audio tracks recorded on the disc when pressed repeatedly.
DVD
DVD : Selects the language.
HDD -RWVR : Selects the main or sub sound.
CD
VCD
: Selects stereo or monaural audio tracks.
Selects a subtitle language when pressed repeatedly.
Playback
(subtitle)
CD
DVD
(angle)
Selects an angle when pressed repeatedly.
If various angles (multi-angles) for a scene are recorded on the disc, “
appears in the front panel display.
DVD
SUR (surround)
+RW
+R
-RWVR -RWVideo
-R
DVD
”
Selects one of the TVS effects when pressed repeatedly.
TVS* (TV Virtual Surround) lets you enjoy virtual surround sound effects
created from the front left and right speakers. The selected setting is displayed
in the front panel display for a few seconds.
“TVS OFF”: No surround effect
“TVS DYNAMIC”: Creates one set of virtual rear speakers.
“TVS WIDE”: Creates five sets of virtual rear speakers.
“TVS NIGHT”: Creates five sets of virtual rear speakers. Effective at low
volume.
“TVS STANDARD”: Creates three sets of virtual rear speakers. Effective
when you use two separate front speakers.
* TVS was developed by Sony to produce home surround sound with just a stereo
TV.
PROGRESSIVE
+RW
-RWVR
-RWVideo
+R
-R
DVD
VCD
HDD
/
(instant replay/
instant advance)
HDD
+RW
-RWVR
-RWVideo
+R
-R
Switches the type of video output signal to interlace or progressive format
(page 15).
Replays the scene/briefly fast forwards the scene.
DVD
. (previous)/
> (next)
Goes to the beginning of the previous/next title/chapter/scene/track.
For the HDD, you cannot go to the beginning of the previous/next title.
,continued
51
Buttons
Operations
(fast reverse/fast forward)
Fast reverses/fast forwards the disc when pressed during playback.
Search speed changes as follows:
fast reverse fast forward
m1 T t 1M*1
m2 T T t t 2M
m3*2 T T T t t t 3M*2
When you press and hold the button, fast forward/fast reverse continues at the
selected speed until you release the button.
you press M once during playback of a title recorded in the HDD, you
can play quickly with sound (“x1.5” appears).
*2 m3 and 3M are only available for the HDD and DVDs.
*1 When
(slow, freeze frame)
HDD
+RW
-RWVR
-RWVideo
+R
-R
Plays in slow motion when pressed for more than one second in pause mode.
Plays one frame at a time when pressed briefly in pause mode.
VCD *
DVD
* Playback direction only
X (pause)
Pauses playback.
To resume normal playback, press H.
52
b Notes
Notes on playing DTS sound tracks on a CD
• To enjoy the TVS function, set “Digital Out” to “On”
and “Dolby Digital” to “D-PCM” and “MPEG” to
“PCM” in “Audio” setup.
• The volume may be reduced when surround effects are
set.
• When the playback signal does not contain a signal for
the rear speakers, the surround effects will be difficult
to hear.
In addition, the surround effects may also be difficult to
hear depending on the title being played and the
environment where the recorder is being used.
• When you select one of the surround modes, turn off
the surround settings of the connected TV or amplifier
(receiver).
• Make sure that your listening position is between and
at an equal distance from your speakers, and that the
speakers are located in similar surroundings.
• Angles and subtitles cannot be changed with titles
recorded on this recorder.
• When you use the DIGITAL OUT (COAXIAL or
OPTICAL) jack to listen to MPEG audio signals and
set “MPEG” to “MPEG” in “Audio” setup, no sound
will come from your speakers if you select one of the
TVS modes.
• 96 kHz PCM audio and DTS audio do not have
surround effects.
• The surround effects do not work while performing
playback quickly with sound.
• When playing DTS-encoded CDs, excessive noise will
be heard from the analogue stereo jacks. To avoid
possible damage to the audio system, the consumer
should take proper precautions when the analogue
stereo jacks of the recorder are connected to an
amplification system. To enjoy DTS Digital
Surround™ playback, an external 5.1-channel decoder
system must be connected to the digital jack of the
recorder.
• Set the sound to “Stereo” using the
(audio)
button when you play DTS sound tracks on a CD
(page 51).
Notes on playing DVDs with a DTS sound track
DTS audio signals are output only through the DIGITAL
OUT (COAXIAL or OPTICAL) jack.
When you play a DVD with DTS sound tracks, set
“DTS” to “On” in “Audio” setup (page 88).
3
Adjusting the picture quality
HDD
DVD
1
+RW
-RWVR -RWVideo
+R
-R
VCD
Press TOOLS during playback to select
“Video Settings,” and press ENTER.
Video Settings
Select the item you want to change.
2
C NR :
2
BNR :
2
MNR :
1
DVE :
Off
PB Video Equalizer
2
Select an item, and press ENTER.
The adjustment display appears.
“Y NR” (luminance noise reduction):
Reduces noise contained in the luminance
element of the video signal.
“C NR” (chroma noise reduction): Reduces
noise contained in the colour element of the
video signal.
“BNR” (block noise reduction): Reduces
“block noise” or mosaic like patterns in the
picture.
“MNR” (mosquito noise reduction): Reduces
the faint noise appearing around the outlines
of the images. The noise reduction effects are
automatically adjusted within each setting
range according to the video bit rate and other
factors.
“DVE” (digital video enhancer): Sharpens the
outlines of the images.
“PB Video Equalizer” (Playback video
equalizer): Adjusts the picture in greater
detail.
Select an item and press ENTER.
• Contrast: changes the contrast.
• Brightness: changes the overall brightness.
• Colour: makes the colours deeper or lighter.
• Hue: changes the colour balance.
The default settings are underlined.
“Y NR”: (weak) Off 1
2 3 (strong)
“C NR”: (weak) Off 1
2 3 (strong)
“BNR”: (weak) Off 1
2 3 (strong)
“MNR”: (weak) Off 1
2 3 (strong)
“DVE”*: (weak) Off 1
2 3 (strong)
“PB Video Equalizer”:
• Contrast: (weak) –3 ~ 0 ~ 3 (strong)
• Brightness: (dark) –3 ~ 0 ~ 3 (bright)
• Colour: (light) –3 ~ 0 ~ 3 (deep)
• Hue: (red) –3 ~ 0 ~ 3 (green)
Repeat steps 2 and 3 to adjust any other items.
* “1” softens the outlines of the images. “2”
enhances the outlines and “3” enhances them more
than “2.”
Playback
Y NR :
Press </, to adjust the setting, and
press ENTER.
b Notes
• If the outlines of the images on your screen become
blurred, set “BNR” and/or “MNR” to “Off.”
• Depending on the disc or the scene being played, the
above BNR, MNR, Y NR, or C NR effects may be hard
to discern. And, these functions may not work with
some screen sizes.
• When using the DVE function, noise found in the title
may become more apparent. In this case, it is
recommended that you use the BNR function with the
DVE function. If the condition still does not improve,
set the DVE level to “1” or “Off.”
,continued
53
Adjusting the sound quality
HDD
DVD
+RW
VCD
-RWVR -RWVideo
CD
+R
Pausing a TV Broadcast (TV Pause)
-R
DATA CD
1
Press TOOLS during playback to select
“Audio Settings,” and press ENTER.
2
Select an item, and press ENTER.
You can pause a current TV broadcast, and then
continue watching the programme at a later time.
This is useful when you receive an unexpected
phone call or visitor while watching TV.
1
“Surround” (TVS): Selects one of the
surround modes. For more information, see
“Playback options” on page 51.
While viewing a TV broadcast with this
recorder, press X.
The picture pauses. You can pause the picture
for up to three hours.
News
“Audio Filter”: Selects the digital filter to
reduce noise above 22.05 kHz (Fs* is 44.1
kHz), 24 kHz (Fs is 48 kHz), or 48 kHz (Fs is
above 96 kHz).
• Sharp (default): Provides a wide frequency
range and spatial feeling.
• Slow: Provides smooth and warm sound.
“AV SYNC”: When the video is delayed, this
function delays the audio for synchronization
with the video (0 to 120 milliseconds). Larger
numbers indicate a longer audio delay for
synchronization with the video. When
dubbing to a VCR or other video recording
equipment, be sure to return this setting to 0
ms (default).
* Sampling frequency of audio source. This
function only adjusts the output signals from the
LINE OUT (R-AUDIO-L).
3
Press </M/m/, to select the option,
and press ENTER.
b Note
There may be little effect by changing the Audio Filter
depending on the disc or playback environment.
54
ABCD 9
Stereo
TV pause
2
Press X or H again to resume watching
the programme.
b Notes
• Paused titles are not saved to the HDD.
• This function is cancelled when:
– x (stop) is pressed.
– PROG +/– is pressed.
– DVD is pressed.
– Z (open/close) is pressed.
– TITLE LIST is pressed.
– INPUT SELECT is pressed.
– the recorder is turned off.
– a timer recording or Synchro-Recording is started.
– DV dubbing or regular dubbing is started.
• It may take a few seconds to resume playback of the
paused programme.
• Even if you fast forward the recorded programme,
there will always be a time difference of about one
minute or more between the recorded programme and
the current TV broadcast.
Playing from the beginning of the
programme you are recording
(Chasing Playback)
HDD
-RWVR
“Chasing Playback” allows you to view the
recorded part of a programme while the recording
is being made. You do not need to wait until the
recording finishes.
Playback starts from the beginning of the
programme you are recording.
When you fast forward to the point that you are
recording, Chasing Playback returns to normal
playback.
b Notes
• For DVD-RWs (VR mode), this function does not
work when recording:
– on a 1x-speed DVD-RW.
– in the HQ or HSP recording mode.
• The DVD’s picture on your TV screen freezes for a few
seconds when you fast forward/fast reverse or instant
replay/advance the recording.
• Chasing Playback is possible from one minute or more
after recording starts.
• Even if you fast forward the recorded programme,
there will always be a time difference of about one
minute or more between the recorded programme and
the current TV broadcast.
HDD
DVD
+RW -RWVR -RWVideo
+R
VCD
CD DATA DVD DATA CD
-R
“Simultaneous Rec and Play” allows you to view
a previously recorded programme while recording
programmes. Playback continues even if a timer
recording starts. Use this function as follows:
• While recording to the HDD:
Play another title on the HDD.
Play a previously recorded programme on a
DVD by pressing DVD.
• While recording to a DVD:
Play a previously recorded programme on the
HDD by pressing HDD.
• While recording to a DVD-RW (VR mode)*1:
Play another title on the same DVD-RW (VR
mode) disc.*2
Playback
Press TOOLS while recording to select
“Chasing Playback,” and press ENTER.
Playing a previous recording while
making another (Simultaneous Rec
and Play)
*1
Simultaneous Rec and Play function does not work
when you record:
– on a 1x-speed DVD-RW.
– in the HQ or HSP recording mode.
*2 Picture noise may appear depending upon the
condition of the recording, or when playing a title
recorded in the HQ or HSP recording mode. The
picture freezes for a few seconds when you use fast
forward/fast reverse or instant replay/advance.
You can also play a DVD VIDEO, VIDEO CD,
Super VIDEO CD, CD, DATA DVD, or DATA
CD while recording on the HDD.
Example: Play another title on the HDD while
recording to the HDD.
1
While recording, press TITLE LIST to
display the HDD Title List.
2
Select the title you want to play, and press
ENTER.
3
Select “Play” from the sub-menu, and press
ENTER.
Playback starts from the selected title.
,continued
55
Example: Play a DVD while recording to the
HDD.
1
While recording, press DVD and insert the
DVD into the recorder.
2
Press TITLE LIST to display the DVD Title
List.
3
Select the title you want to play, and press
ENTER.
4
Searching for a Title/
Chapter/Track, etc.
Number
buttons, SET
Select “Play” from the sub-menu, and press
ENTER.
Playback starts from the selected title.
1
2
3
4
5
6
7
8
9
CLEAR
0
b Note
</M/m/,,
ENTER
You cannot play a DVD or VIDEO CD recorded in the
NTSC colour system while recording on the HDD. When
playing a VIDEO CD, be sure to set “Colour System” to
“PAL” (page 90).
TOOLS
VISUAL
SEARCH
Searching by Thumbnail (Visual
Search)
HDD
+RW
-RWVR -RWVideo
+R
-R
Each chapter is displayed as a thumbnail. You can
search for the desired scene visually.
1
Press VISUAL SEARCH during playback.
VISUAL SEARCH
9 World Sports
Chapter 4(30)
0:12:45
2
Select a scene using </,, and press
ENTER.
Playback of the selected scene is started.
56
Searching by title number or time
code
HDD
DVD
+RW
VCD
-RWVR -RWVideo
CD
+R
-R
DATA DVD DATA CD
3
Press SET.
The recorder starts playback from the selected
number.
b Note
“Title Search” is not applicable to the HDD.
You can search a disc by title, chapter, scene or
track. As titles and tracks are assigned individual
numbers, select the title or track by entering its
number. You can also search for a scene using the
time code.
Press TOOLS during playback to select a
search method, and press ENTER.
Playback
1
“Title Search” (for DVDs)
“Chapter Search” (for HDD/DVDs)
“Track Search” (for CDs/DATA CDs)
“Search” (for VIDEO CDs)
“Album Search” (for DATA DVDs/DATA
CDs)
“Time Search” (for HDD/DVDs): Searches
for a starting point by entering the time code.
“File Search” (for DATA DVDs/DATA CDs)
The display for entering the number appears.
Example: Title Search
Title : -- (21)
The number in parentheses indicates the total
number of titles, tracks, etc.
2
Press the number buttons to select the
number of the title, chapter, track, time
code, etc., you want.
For example: Time Search
To find a scene at 2 hours, 10 minutes, and 20
seconds, enter “21020.”
If you make a mistake, press CLEAR to
cancel the number, then select another
number.
57
Playing MP3 Audio Tracks
or JPEG Image Files
Selecting an MP3 album or track
1
Press TITLE LIST.
The album list appears.
To change the page, press
DATA DVD DATA CD
You can play MP3 audio tracks and JPEG image
files on DATA CDs (CD-ROMs/CD-Rs/CDRWs) or JPEG image files on DATA DVDs
(DVD-ROMs/DVD+RWs/DVD+Rs/DVD-RWs/
DVD-Rs).
1
2
3
4
5
6
7
8
9
.
TITLE LIST
Music Album
2
1
Opera
Classic
2
Symphony
Classic
3
Samba
Dance
4
Live
Jazz
5
Piano
Jazz
6
My heart
Pop music
7
Paradise
Pop music
8
The Best
Pop music
Select an album, and press ENTER.
The sub-menu appears.
3
0
DISPLAY
/
Select “View Album,” and press ENTER.
The track list appears.
To change the page, press
TIME/TEXT
/
.
TITLE LIST
</M/m/,,
ENTER
/
TITLE LIST
8 The Best
1
01 Holiday
2
02 Lonely
>
M
H
3
03 Candy
4
04 Rainy day
5
05 Station
6
06 Magic
x
7
07 Moon
8
08 Butterfly
TOOLS
.
m
4
1
Insert a disc.
See “Inserting a Disc” on page 25.
2
“Play”: Plays the track.
“Play Beginning”: Plays the beginning of the
track.
“Track Data”: Shows data about the track
such as artist and album name.
Press H.
For MP3 discs, playback starts from the first
MP3 audio track on the disc.
For JPEG files, a slideshow of the pictures on
the disc begins.
If the DATA CD contains both MP3 audio
tracks and JPEG image files, playback starts
from the JPEG image files the first time H is
pressed.
58
Select a track, and press ENTER.
To stop playback
Press x.
To fast forward or review a track
Press m/M during playback.
To go to the previous or next MP3 audio track
Press . or > during playback. If you
repeatedly press . or >, you will go to the
previous or next album.
To go to the previous or next album
To stop viewing the JPEG image
Press
Press x.
during playback.
/
z Hint
Press the
To view the previous or next picture
(audio) button to switch between stereo
or monaural audio tracks.
Press ./> while the picture is displayed.
To rotate a picture
Selecting a JPEG album or image
1
Press TITLE LIST.
To change the slideshow speed
/
.
TITLE LIST
Photo Album
1
Flowers
ROOT
2
Aquarium
Summer
3
Festival
Summer
4
Hiking
Summer
5
Tennis match
Summer
6
Zoo
Summer
7
Consert
Winter
8
Party
Winter
To go to the previous or next album
Press
Select an album, and press ENTER.
The sub-menu appears.
3
Select “View Album,” and press ENTER.
The image list appears.
To change the page, press
/
.
TITLE LIST
6 Zoo
/
while the JPEG image is displayed.
z Hints
• If you are playing a DATA CD that has both MP3 and
JPEG files, you can switch between photo and music
albums by using the </, buttons when the album
list is displayed.
• You can rotate a JPEG image by using the </,
buttons when the image is displayed.
• Press DISPLAY repeatedly to show information about
the JPEG album or image on your TV screen. Then
press TIME/TEXT to toggle between the current
selected image number and album number.
b Notes
1
2
3
4
5
6
7
8
9
10
11
12
DSC00029 25.11.2005 15:50
4
Press TOOLS while the album list or image list is
displayed to select “Slideshow Speed,” and press
ENTER. Then select the speed from “Fast”
(quick), “Normal,” and “Slow.”
Playback
The album list appears.
To change the page, press
2
Press TOOLS while the image is displayed to
select “Rotate Right” or “Rotate Left,” and press
ENTER.
Select an image, and press ENTER.
“View Image”: Shows the image on the entire
screen.
“Slideshow”: Shows the images in the album
as a slideshow.
“Image Data”: Shows data about when the
picture was taken.
• If the DVD disc, such as a disc from a DVD video
camera, contains both video and JPEG images, only the
video can be played back.
• Some JPEG files, especially files of three million
pixels or more, may lengthen the slideshow interval.
• Rotated JPEG images will not be saved when you press
x or switch to another folder.
• Images larger than 720 × 480 will be reduced to 720 ×
480 when displayed.
• Images larger than 4 mega bytes cannot be displayed.
• Progressive JPEG images cannot be displayed.
• When you attempt to play a broken file or a file that
does not satisfy the play conditions,
appears but
the recorder cannot play the file.
,continued
59
About MP3 audio tracks and JPEG
image files
MP3 audio tracks or JPEG image
files that the recorder can play
MP3 is audio compression technology that
satisfies certain ISO/MPEG regulations. JPEG is
image compression technology.
You can play MP3 (MPEG1 Audio Layer 3)
format audio tracks and JPEG image files on
DATA CDs (CD-ROMs/CD-Rs/CD-RWs) or
JPEG image files on DATA DVDs (DVD-ROMs/
DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs).
DATA CDs must be recorded according to
ISO9660 Level 1, Level 2 or Joliet format for the
recorder to recognize the MP3 tracks. DATA
DVDs must be recorded in Universal Disc Format
(UDF). You can also play discs recorded in
MultiSession.
See the instructions supplied with the CD-R/CDRW/DVD-R/DVD-RW drives and the recording
software (not supplied) for details on the recording
format.
The recorder can play the following tracks and
files:
– MP3 audio tracks with the extension “.MP3,”
“.mp3,” or “.Mp3.”
– JPEG image files with the extension “.JPEG,”
“.jpg,” “.JPG,” “.Jpg,” “.jpeg,” or “.Jpeg.”
– JPEG image files that conform to the DCF*
image file format.
Note on MultiSession/Border discs
If MP3 audio tracks or JPEG image files are
recorded in the first session/border, the recorder
will also play MP3 audio tracks or JPEG image
files in other sessions/borders. If audio tracks and
images in Music CD format or Video CD format
are recorded in the first session/border, only the
first session/border will be played back.
b Note
The recorder may not be able to play some DATA CDs/
DATA DVDs created in the Packet Write format.
60
* “Design rule for Camera File system”: Image standards
for digital cameras regulated by JEITA (Japan
Electronics and Information Technology Industries
Association).
b Notes
• The recorder will play any data with the extension
“.MP3,” “.mp3,” “.Mp3,” “.JPEG,” “.jpg,” “.JPG,”
“.Jpg,” “.jpeg,” or “.Jpeg” even if they are not in MP3
or JPEG format. Playing these data may generate a loud
noise which could damage your speaker system.
• The recorder does not conform to audio tracks in
mp3PRO format.
• Some files cannot be played.
• The letters that cannot be displayed are replaced with
“*.”
About playback order of albums,
tracks, and files
Albums play in the following order:
Structure of disc contents
Tree 1
Tree 2
Tree 3
Tree 4
Tree 5
b Notes
Playback
• Depending on the software you use to create the DATA
DVD/DATA CD, the playback order may differ from
the above illustration.
• No more than a total of 199 individual folders can be
played. (Folders that do not contain JPEG/MP3 files
are counted as well.)
• No more than a total of 999 folders and files can be
played. (Files other than JPEG/MP3 files, and folders
that do not contain JPEG/MP3 files are counted as
well.)
• No more than 200 folders and files can be recognized
in a single folder. (Folders that do not contain JPEG/
MP3 files are counted as well.)
• Proceeding to the next or another album may take some
time.
• This recorder supports MP3 audio bit rates up to 160
kbps.
ROOT
Album
z Hints
• If you add numbers (01, 02, 03, etc.) to the front of the
track/file names when you store the tracks (or files) in
a disc, the tracks and files will be played in that order.
• Since a disc with many trees takes longer to start
playback, it is recommended that you create albums
with no more than two trees.
MP3 audio track/
JPEG image file
When you insert a DATA CD/DATA DVD and
press H, the numbered tracks (or files) are
played sequentially, from 1 through 7. For
JPEG image files, press
to go to the next
album. (For instance, when you want to go from
1 to 2.) Any sub-albums/tracks (or files)
contained within a currently selected album take
priority over the next album in the same tree.
(Example: C contains D so 4 is played before
5.) When you press TITLE LIST and the list of
album names appears (page 28), the album names
are arranged in the following order: A t B t
C t D t F t G. Albums that do not
contain tracks (or files) (such as album E) do not
appear in the list.
61
To create and edit Playlist titles
Erasing and Editing
Before Editing
This recorder offers various edit options for
various disc types. Before you edit, check the disc
type in the front panel display, and select the
option available for your disc (page 8).
b Notes
• You may lose the edited contents if you remove the disc
or a timer recording starts while editing.
• DVD discs created by DVD video cameras cannot be
edited on this recorder.
Edit options for the HDD and DVDRWs (VR mode)
A Playlist is a group of Playlist titles created from
the original title for editing purposes. When you
create a Playlist, only the control information
necessary for playback, such as the playback
order, is stored on the disc. Since the original titles
are left unaltered, Playlist titles can be re-edited.
Example: You have recorded the final few
matches of a football tournament on a DVD-RW
(VR mode). You want to create a digest with the
goal scenes and other highlights, but you also want
to keep the original recording.
Original
Playlist
HDD -RWVR
You can enjoy advanced edit functions. First you
have two options for the HDD and DVD-RWs
(VR mode): editing either the original recording
(called the “original”), or the playback
information created from the original (called a
“Playlist”). Since each is different in nature and
offers different merits, read the following and
select the one that better suits your needs.
To edit original titles
Edits made to the original titles are final. If you
plan to retain an unaltered original recording,
create and edit a Playlist (see below). The edit
functions available for original titles are:
– Labelling a title (page 63).
– Setting protection against erasure (page 63).
– Erasing a title (page 63).
– Erasing multiple titles (page 65).
– Erasing a section of a title (A-B Erase) (page 64).
– Erasing all titles on the disc (page 66).
– Erasing a chapter (page 64).
– Dividing one title into two titles (HDD only)
(page 65).
62
In this case, you can compile highlight scenes as a
Playlist title. You can even rearrange the scene
order within the Playlist title (“Creating and
Editing a Playlist” on page 67).
The advanced edit functions available for Playlist
titles are:
– Setting protection against erasure (HDD only)
(page 63).
– Labelling a title (page 63).
– Erasing a title (page 63).
– Erasing multiple titles (page 65).
– Erasing a section of a title (A-B Erase) (page 64).
– Rearranging the title order (DVD-RWs (VR
mode) only) (page 68).
– Dividing a title into multiple titles (page 65).
– Combining multiple titles into one title
(page 69).
– Erasing a chapter (page 64).
z Hint
You can display the disc’s Playlist titles in the Title List
(Playlist), or the original titles in the Title List (Original).
To switch the two Title Lists, press TOOLS while a Title
List is displayed, and select “Original” or “Playlist.”
b Notes
• The Playlist title calls up data from the original titles for
playback. When an original title is used for a Playlist
title, the original title cannot be erased.
• If a message appears and indicates that the disc’s
control information is full, erase or edit unnecessary
titles.
• Playlist titles containing titles recorded with the “CopyOnce” copy protection signal cannot be dubbed or
moved (page 72).
Erasing and Editing a Title
HDD
+RW
-RWVR -RWVideo
+R
-R
This section explains the basic edit functions. Note
that editing is irreversible. To edit the HDD or
DVD-RWs (VR mode) without changing the
original recordings, create a Playlist title
(page 67).
Edit options for DVD+RWs/DVDRWs (Video mode)/DVD+Rs/DVD-Rs
-RWVideo
+R
-R
You can perform simple edits. Since Video mode
titles are actual recordings on the disc, you cannot
undo any edits you make. The edit functions
available for Video mode titles are:
– Setting protection against erasure (page 63).
– Labelling a title (page 63).
– Erasing a title (page 63).
– Erasing multiple titles (page 65).
– Erasing a section of a title (A-B Erase)
(DVD+RWs only) (page 64).
– Erasing all titles on the disc (page 66).
– Erasing titles to open up disc space (Disc Map)
(DVD+RWs and DVD-RWs (Video mode)
only) (page 66).
b Notes
• When editing a DVD+R or DVD-R, finish all editing
before finalizing the disc. You cannot edit a finalized
disc.
• The available disc space does not increase even when
you erase titles for DVD+Rs and DVD-Rs.
• If a message appears and indicates that the disc’s
control information is full, erase or edit unnecessary
titles.
1
2
3
4
5
6
7
8
9
0
TITLE LIST
</M/m/,,
ENTER
Erasing and Editing
+RW
TOOLS
.
m
>
M
X
CHAPTER
MARK
1
CHAPTER
MARK ERASE
Press TITLE LIST.
For HDD titles or DVD-RWs in VR mode,
press TOOLS and select “Original” or
“Playlist” from the TOOLS menu to switch
the Title Lists, if necessary.
2
Select a title, and press ENTER.
The sub-menu appears.
3
Select an option, and press ENTER.
You can make the following edits to the title.
“Erase”: Erases the selected title. Select “OK”
when asked for confirmation.
“Protect”: Protects the title. Select “On” when
the Protection display appears. “ ” appears
next to the protected title. To cancel the
protection, select “Off.”
,continued
63
“Title Name”: Allows you to enter or re-enter
a title name (page 33).
“Set Thumbnail”: Changes the title’s
thumbnail picture that appears in the Title List
(page 30).
“A-B Erase”: Erases a section of the title
(page 64).
“Delete Chapter”: Erases chapter units of the
title while viewing thumbnails (see below).
“Divide”: Divides a title into two titles
(page 65).
z Hints
• You can erase multiple titles at one time (page 65), or
erase all of the titles on the disc at once (page 66).
• You can automatically erase titles that have already
played.
• You can label or re-label DVDs (page 34).
3
Select “OK,” and press ENTER.
The display asks for confirmation.
4
Select “Yes,” and press ENTER.
Erasing a section of a title
(A-B Erase)
HDD
+RW
-RWVR
You can select a section (scene) in a title and erase
it. Note that erasing scenes in a title cannot be
undone.
1
After step 2 of “Erasing and Editing a
Title,” select “A-B Erase” and press
ENTER.
The display for setting point A appears.
• To return to the beginning of the title, press
X and then press ..
b Note
DVD-RW (VR mode) playlist titles cannot be protected.
A–B Erase (Set point A)
5 Weather
Erasing a chapter (Delete Chapter)
HDD -RWVR
Thumbnails are displayed for each chapter. You
can easily select and erase a section in a title.
Note that erasing a chapter cannot be undone.
Playback point
1
After step 2 of “Erasing and Editing a
Title,” select “Delete Chapter,” and press
ENTER.
2
2
Select a thumbnail of the chapter using
</,, and press ENTER.
3
The display for setting point B appears.
Chapter 4(30)
0:12:45
Cancel
Reset All
• To cancel the selection, press ENTER again.
• To erase multiple chapters, repeat step 2.
• To reset all selections, select “Reset All.”
64
Select point B by pressing m/M, and
press ENTER.
The display asks for confirmation.
• To reset either point A or B, select “Change
A” or “Change B,” and go to step 2 or 3.
• To preview the title without scenes to be
erased, select “Preview” (except for
DVD+RWs).
Delete Selected Chapters 9 World Sports
OK
Select point A by pressing m/M, and
press ENTER.
4
Select “OK,” and press ENTER.
The scene is erased, and the display asks
whether to erase another scene.
• To continue, select “Yes,” and repeat from
step 2.
• To finish, select “No.”
z Hint
A chapter mark is inserted after the scene was erased. The
chapter mark divides the title into separate chapters on
either side of the mark.
b Notes
• Images or sound may be momentarily interrupted at the
point where you erase a section of a title.
• Sections shorter than five seconds may not be erased.
• For DVD+RWs, the erased section may be slightly
different from the points you selected.
5
When you finish selecting titles, select
“OK,” and press ENTER.
The list of the titles to be erased appears for
confirmation.
• To change the selection, select “Change,”
and repeat from step 3.
6
Select “OK” and press ENTER.
The titles are erased.
Dividing a title (Divide)
Erasing multiple titles (Erase
Titles)
+RW
-RWVR -RWVideo
+R
-R
You can select and erase more than one title at one
time using the TOOLS menu.
1
2
Press TITLE LIST.
Press TOOLS to select “Erase Titles,” and
press ENTER.
The display for selecting titles to be erased
appears.
3
Select a title, and press ENTER.
A check mark appears in the check box next to
the selected title.
• To clear the check mark, press ENTER
again.
• To clear all of check marks, select “Reset
All.”
Erase Titles
Select the titles to erase.
4
If you want to dub a long title to a disc but do not
want to reduce the picture quality, divide the title
into two shorter titles. Note that dividing a title
cannot be undone.
* Only playlist titles can be divided for DVD-RW (VR
mode).
1
Press TITLE LIST.
Erasing and Editing
HDD
HDD -RWVR *
Press TOOLS and select “Original” or
“Playlist” from the TOOLS menu to switch
the Title Lists, if necessary.
2
Select a title, and press ENTER.
The sub-menu appears.
3
Select “Divide,” and press ENTER.
The display for setting the dividing point
appears. The title starts to play in the
background.
• To return to the beginning of the title, press
X and then press ..
OK
12
Tennis
28.10
11
Travel
26.10
10
Mystry
25.10
9
World Sports
19.10
8
Family
17.10
Cancel
Divide
1 Vacation
Reset All
Repeat step 3 to select all of the titles you
want to erase.
,continued
65
4
Select the dividing point by pressing m/
M, and press ENTER.
The display asks for confirmation.
• To change the dividing point, select
“Change.”
5
+RW
Select “OK,” and press ENTER.
The display for entering the title name
appears.
• To use the same title name as before, select
“No.”
6
Erasing titles to open up disc
space (Disc Map)
Select “Yes,” and press ENTER to enter a
new name.
Follow the explanations on page 33. After you
enter a new name, the title is divided in two.
When recording on a DVD+RW or DVD-RW
(Video mode), the recorder searches for the largest
open space and records there. Before you start,
check the disc status by using Disc Map, and erase
titles to create a space large enough for the
recording.
1
2
1
+RW
-RWVR -RWVideo
+R
Insert a disc and press TITLE LIST.
Press TOOLS to select “Disc Map,” and
press ENTER.
The “Disc Map” display appears.
• To check the open space, select the space by
pressing </,.
Erasing all titles on the disc
HDD
-RWVideo
-R
Disc Map
Press TOOLS to select “Disc Info,” and
press ENTER.
Empty Title
HQ: 0H30M
LP : 1H30M
HSP: 0H45M
EP : 2H00M
SP : 1H00M
SLP: 3H00M
2.3 GB
LSP: 1H15M
SEP: 4H00M
The “Disc Information” display appears.
2
3
Select “Erase All,” and press ENTER.
Select “OK,” and press ENTER.
Erase
All titles on the disc are erased (except the
protected titles).
Cancel
• When b or B appears on either side of the
screen, you can scroll sideways by pressing
</,.
3
Select a title by pressing </,, and
press ENTER.
The display for selecting titles to be erased
appears.
• To cancel the selection, press ENTER again.
• To erase more titles, repeat step 3.
Disc Map
2 Journey
Fri 17.9.2004 20:00 (1H00M)
Erase
Selected title
66
SP 0.6GB
Cancel
4
Select “Erase,” and press ENTER.
The display asks for confirmation.
5
Select “OK,” and press ENTER.
The selected titles are erased, freeing up disc
space.
• To change the selection, select “Change.”
Creating chapters manually
HDD
-RWVR
You can manually insert a chapter mark at any
point you like during playback or recording.
HDD -RWVR
Playlist edit allows you to edit or re-edit without
changing the actual recordings. You can create up
to 97 Playlist titles.
b Note
Once you create a Playlist title from original titles, you
will be unable to erase or edit the original titles.
1
2
Each time you press the button, “Marking...”
appears on the screen and the scenes to the left and
right of the mark become separate chapters.
Press TITLE LIST.
Press TOOLS to select “Create Playlist,”
and press ENTER.
Create Playlist
Select a title to start capturing.
Scene List
ORIGINAL
To erase chapter marks
You can combine two chapters by erasing the
chapter mark during playback.
Press ./> to search for a chapter number, and
while displaying the chapter containing the
chapter mark you want to erase, press CHAPTER
MARK ERASE.
The current chapter combines with the previous
chapter.
b Notes
• When dubbing, any chapter marks you enter will be
erased.
• To insert a chapter mark manually during recording, set
“Auto Chapter” in “Features” setup to “Off.”
3
Cancel
12
Tennis
28.10
11
Travel
26.10
10
Mystry
25.10
9
World Sports
19.10
8
Family
17.10
7
Nature
15.10
Erasing and Editing
Press CHAPTER MARK at the point where you
want to divide the title into chapters.
Creating and Editing a
Playlist
Select the title you want to include in the
Playlist title, and press ENTER.
The sub-menu appears.
“Capture”: Adds a section of the title to the
Playlist title as one scene.
“Capture All”: Adds the entire title to the
Playlist title as one scene. After capturing the
title, go to step 8.
4
Select “Capture,” and press ENTER.
The display for setting the start point (IN)
appears. The title starts to play in the
background.
• To return to the beginning of the title, press
X and then press ..
Capture(Set IN point)
9 World Sports
,continued
67
5
Select the IN point by pressing m/M,
and press ENTER.
9
The display for setting the end point (OUT)
appears, and the title continues to play in the
background.
6
Select the OUT point by pressing m/M,
and press ENTER.
The display asks for confirmation.
To reset the IN or OUT point, select “Change
IN” or “Change OUT” and repeat step 5 or 6.
To view the selected scene, select “Preview.”
7
Select “OK,” and press ENTER.
The Scene List menu appears with all of the
selected scenes.
Total duration of
the selected scene
Scene List
Total number of scenes
Total 0:13:19
Scenes 1
When you finish editing the Scene List,
select “OK,” and press ENTER.
The display for entering the title name
appears. To enter a new name, select “Enter”
(page 33).
10 Select “OK” to use the default name, and
press ENTER.
To play the Playlist title
Press TOOLS while the Title List menu is turned
on. Then, select “Playlist” and press ENTER.
When the Title List (Playlist) menu appears, select
a title and press H.
z Hint
When a Playlist title is created, the IN and OUT points
will become chapter marks, and each scene will become
a chapter.
OK
1
World Sports
Quit
0:10:26 - 0:23:45
Add
b Note
The picture may pause when the edited scene is played.
Preview
• To add more scenes, select “Add” and go to
step 3.
• To preview all of the captured scenes in the
listed order, select “Preview.”
8
Select the scene you want to re-edit, and
press ENTER.
The sub-menu appears.
“Move”: Changes the scene order.
“Erase”: Erases the scene. The selection is
cancelled.
“Preview”: Displays thumbnail pictures of the
scenes.
“Change IN”: Allows you to change the IN
point, and repeat from step 5.
“Change OUT”: Allows you to change the
OUT point, and repeat from step 6.
Moving a Playlist title (Change
Order)
-RWVR
You can change the Playlist title order within the
Title List (Playlist).
1
Press TITLE LIST to turn on the Title List
(Playlist) menu.
If the Title List (Original) menu appears, press
TOOLS and select “Playlist.”
2
Select the title you want to move, and
press ENTER.
The sub-menu appears.
3
Select “Change Order,” and press ENTER.
Change Order
1
Vacation
15.9
Cancel
Where do you want to move this title?
2
4
Journey
17.9
Select a new location for the title by
pressing M/m, and press ENTER.
The title moves to the new location.
68
Combining multiple Playlist titles
(Combine)
6
The display for selecting a title name from
among the selected titles appears.
To enter a new name, select “Enter Text,” and
follow the explanations on page 33.
To change the selection, select “Change” and
go to step 3.
HDD -RWVR
1
Press TITLE LIST to turn on the Title List
(Playlist) menu.
If the Title List (Original) menu appears, press
TOOLS and select “Playlist.”
2
Press TOOLS to select “Combine,” and
press ENTER.
The display for selecting titles appears.
Select a title, and press ENTER.
A number indicating the order in which you
selected the title appears.
To cancel the selection, press ENTER again.
Select the titles to combine.
4
Select a name, and press ENTER.
The titles are combined.
b Note
When the number of chapters in the title to be combined
exceeds the limit, the chapters at the end are combined
into a single chapter.
Dividing a Playlist title (Divide)
HDD -RWVR
Combine
1
7
OK
4
Yacht
25. 9
3
Cruising
25. 9
2
Journey
17. 9
1
Vacation
15. 9
Cancel
You can divide a Playlist title. For operations, see
page 65.
Erasing and Editing
3
Select “OK,” and press ENTER.
Reset All
Repeat step 3 to select all of the titles you
want to combine.
To cancel all of the selections, select “Reset
All.”
5
Select “OK,” and press ENTER.
The list of titles to be combined appears.
To change the selection, select “Change” and
go to step 3.
Combine
Combine the titles in the following order.
1
4
Yacht
25. 9
2
3
Cruising
25. 9
OK
Change
Cancel
69
Dubbing (HDD y DVD)
Before Dubbing
HDD
+RW
-RWVR -RWVideo
+R
-R
In this section, “dubbing” refers to “copying a
recorded title on the internal hard disk drive
(HDD) to another disc, or vice versa.” You can
select to dub one title at a time (Title Dubbing –
see “Dubbing a single title (Title Dub)” on
page 72), or multiple titles all at once (Multiple
Title Dubbing – see “Dubbing multiple titles (Dub
Selected Titles)” on page 73).
Before you start, read the following precautions,
which are common to both dubbing methods.
If you want to record from a digital video camera
connected to the DV IN jack, see “DV Dubbing”
on page 75. To record from equipment connected
to the LINE IN jacks, see “Recording from
connected equipment without a timer” on page 47.
Before you start…
• Select the disc type according to your needs
(page 8). This recorder can record on various
discs.
• You cannot record both the main and sub sound
on a DVD+RW, DVD-RW (Video mode),
DVD+R, or DVD-R. For bilingual programs, set
“DVD Bilingual Rec.” to either “Main” (default)
or “Sub” in “Options” setup (page 91).
• Timer recordings and Synchro-Recording do not
start during dubbing. Before you start, check the
Timer List menu to see if there is any timer
recording due to start during dubbing.
• When “Auto Chapter” of “Features” setup is set
to “On,” chapter marks are automatically
inserted at approximately 6-minute intervals
while dubbing from the HDD to a DVD, or when
the recorder detects picture and sound changes
while dubbing from a DVD to the HDD. The
chapter marks in the dubbing source are not
retained in the dubbed title.
70
• For a title whose picture size (16:9 or 4:3) is
mixed:
– When dubbed from the HDD to DVD-RW
(Video mode) or DVD-R, the picture size is
determined by the setting in “DVD Rec.
Picture Size” (page 42).
– When dubbed from HDD to DVD+RW or
DVD+R, the picture size is always 4:3.
– When dubbed from HDD to DVD-RW (VR
mode), the originally recorded picture size is
retained.
z Hints
• When you dub a Playlist title, it is recorded as an
Original title.
• When dubbed from a DVD to the HDD, the picture size
and the sound types originally recorded are retained.
b Notes
• To play a dubbed disc on other DVD equipment,
finalize the disc (page 35).
• The recorder may not function as described depending
on the disc status. Follow the instructions that appear on
the screen.
• You cannot dub from DVD VIDEOs to the HDD.
• Thumbnails that you have set for the originally
recorded title (page 30) will not be retained in the
dubbed title.
About “Dub Mode”
With this recorder, the recording mode for
dubbing is displayed as “Dub Mode.” Two
dubbing method are available: High-speed
Dubbing and Rec Mode Conversion Dubbing.
Read the following and select according to the
required time, disc space, and picture quality.
Dubbing at high-speed (High-speed Dubbing)
HDD , +RW / -RWVR / -RWVideo / +R /
-R
Allows you to dub what you have stored in the
HDD to a high-speed DVD (8x-speed
DVD+RWs/6x-speed DVD-RWs/16x-speed
DVD+Rs/16x-speed DVD-Rs, or slower versions
of each disc type), without changing the recording
mode.
Set “Dub Mode” to “Fast” in “Title Dub” or “Dub
Selected Titles” display (page 72). You cannot
select “Fast” when titles that cannot be dubbed at
high speed are selected (such as the titles displayed
in “Notes” below). The minimum required time is
as follows (approximate).
Required times for High-speed Dubbing from
HDD to DVD (for 60-minute programme)*1
Speed*2 6x
6x*3
8x*4
8x*4
Highspeed
DVD+
RW
Highspeed
DVD-R
High- DVD+R
speed (Double
DVD+R Layer)
2.4x
HQ
10 min. 10 min. 8 min. 8 min. 25 min.
HSP
6 min. 6 min. 5 min. 5 min. 16 min.
40 sec. 40 sec.
40 sec.
SP
5 min. 5 min. 3 min. 3 min. 12 min.
45 sec. 45 sec. 30 sec.
LSP
4 min. 4 min. 3 min. 3 min. 10 min.
LP
3 min. 3 min. 2 min. 2 min. 8 min.
20 sec. 20 sec. 30 sec. 30 sec. 20 sec.
EP
2 min. 2 min. 2 min. 2 min. 6 min.
30 sec. 30 sec.
15 sec.
SLP
1 min. 60
60
1 min. 60
40 sec. min.*5 15 sec. min.*5 min.*5
SEP
1 min. 60
56 sec. 60
60
15 sec. min.*5
min.*5 min.*5
*1
*2
*3
*4
*5
The values in the above table are for reference only.
Actual times for dubbing also require time for creating
disc’s control information and other data.
This is the maximum recording speed of this recorder.
The value may vary depending on the disc condition.
Also, this recorder may be unable to record at the
maximum speed for discs that support recording
speeds exceeding the maximum value.
The maximum drive speed of this recorder is 6x when
using 6x-speed or faster DVD+RWs.
The maximum drive speed of this recorder is 8x when
using 8x-speed or faster DVD+Rs/DVD-Rs.
High-speed dubbing is not available when dubbing
titles recorded in SLP and SEP mode to DVD+RWs
and DVD+Rs.
• High-speed Dubbing is not available for the following
titles:
– Titles recorded in HQ+.
– Titles that contain both main and sub sounds (except
DVD-RWs (VR mode)).
– Titles recorded in mixed picture size (4:3 and 16:9
etc.), (except DVD-RWs (VR mode)).
• When dubbed to a DVD-RW (Video mode)/
DVD+RW/DVD+R/DVD-R, remnants of edited titles
may remain on the disc. If you edit a title, use the Rec
Mode Conversion Dubbing method. This will smooth
out the pauses between the scenes.
• When playing a dubbed DVD+R DL disc, the video and
audio may be momentarily interrupted at the point
where the layers switch.
Rec Mode Conversion Dubbing
HDD n +RW / -RWVR / -RWVideo /
+R
/
-R
Allows you to dub from the HDD to a DVD or vice
versa, in a dubbing mode that differs from the
original recordings. For example, when you dub
an HQ title (data size is large) in SP mode, you can
reduce the data size, saving more titles using less
space.
Select a mode different from the original recording
in “Dub Mode” in the steps of “Dubbing a single
title (Title Dub)” on page 72 or “Dubbing multiple
titles (Dub Selected Titles)” on page 73.
When a title recorded to HDD in HQ or HQ+ mode
is converted to another mode, the recorder
automatically assigns an appropriate bit rate, thus
retaining the original picture quality as much as
possible.
Dubbing (HDD y DVD)
Rec.
mode
Highspeed
DVDRW
b Notes
b Note
The picture quality will not improve even if a title is
converted to a recording mode of better picture quality.
,continued
71
Dubbing restriction
You cannot dub movies and other DVD Videos to
the HDD. Also, when dubbing from a DVD to the
HDD, a gray, blank screen will be recorded for
scenes that contain a copy protection signal.
Copy
protection
signals
Copy-Once
HDD
HDD
,
,
Copy-Free
(No copy
protection
signal)
Dubbing
,
HDD
+RW
-RWVR -RWVideo
+R
-R
Dubbing a single title (Title Dub)
+RW
-RWVR
-RWVideo
+R
-R
-RWVR
Dubbing
*
* CPRM-compatible DVD-RWs (VR mode) only
CPRM (Content Protection for Recordable Media) is a
coding technology that protects copyrights for images.
1
Insert the DVD that you are going to dub to
or from.
2
3
Press HDD or DVD to select the source.
4
Select a title, and press ENTER.
Press TITLE LIST to turn on the Title List
menu.
The sub-menu appears.
5
Select “Dubbing,” and press ENTER.
The display for selecting the dubbing mode
appears.
If a title with
(page 72) is selected in the
title list, a confirmation screen is displayed.
To “Move,” select “Yes.”
Move
HDD , -RWVR
Titles containing “Copy-Once” copy protection
signals can be moved only from HDD to DVDRW (VR mode)* (after the title is moved, the
original title in the HDD is erased). The “Move”
function is performed using the same procedure as
dubbing (page 72). Titles containing “CopyOnce” copy protection signals are indicated with
.
Title Dub
2.0GB
2.6GB
This title will be dubbed. Set the dub mode.
1 World Cup Final
b Notes
Dub Mode
SP 2.0GB
• The following titles in the HDD cannot be moved.
– Protected titles
– Playlist titles
– Original titles referenced from the playlist
• If the move operation is stopped before completion, the
title in the HDD is not erased.
Rec Mode: SP
Start
Cancel
A Size of the title (approximate)
B Direction of dubbing
C Available space on the disc to be
dubbed (approximate)
* CPRM-compatible DVD-RWs (VR mode) only.
D Information about the title to be dubbed
E Dubbing mode and the space that
remains after dubbing (approximate)
6
72
Select “Dub Mode.”
7
Select a dubbing mode by pressing M/m.
Fast*
HQ
SEP
HSP
SLP
SP
EP
LSP
LP
* Appears when High-speed Dubbing is available
for the title (page 70).
8
Select “Start,” and press ENTER.
The dubbing indication appears in the front
panel display (page 32).
To automatically adjust the dubbing mode
(Auto Dub Mode)
A maximum of 30 selected titles can be dubbed at
once. You can select the dubbing mode for each
title.
1
Insert the DVD that you are going to dub to
or from.
2
3
Press HDD or DVD to select the source.
4
Press TOOLS to select “Dub Selected
Titles,” and press ENTER.
Dub Selected Titles
Cancel
5
Select “Auto Dub Mode” and press ENTER to
start dubbing. To manually select another dubbing
mode, select “Reset,” and go to step 7.
z Hints
• If disc space is still insufficient for the selected dubbing
mode, erase unnecessary parts of the title, or free up
disc space by erasing titles on the disc (page 66).
• You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned off.
Start
Cancel
4 World Tour – Asia 3
25.6
3 World Cup Final
20.6
2 World Tour – Asia 2
18.6
1 World Tour – Asia 1
11.6
Settings
Reset
Select titles in the order you want to dub,
and press ENTER.
The titles are numbered in the selected order.
To cancel the selection, press ENTER again.
If a title with
(page 72) is selected in the
title list, a confirmation screen is displayed.
To “Move,” select “Yes.”
To stop dubbing
Press TOOLS to select “Stop Dubbing,” and press
ENTER. When asked for confirmation, select
“Yes,” and press ENTER.
4.6GB
ORIGINAL
There is not enough memory for the dubbing.
Select "Auto Dub Mode" or adjust the mode.
Reset
0.0GB
Select title(s) in the order you want to dub them.
Title Dub
Auto Dub Mode
Press TITLE LIST to turn on the Title List
menu.
Dubbing (HDD y DVD)
If there is not enough available space on the target
disc, the recorder automatically selects a dubbing
mode with lower picture quality according to the
available space. If there is insufficient disc space
in the selected dubbing mode, the following
display appears after step 8.
Dubbing multiple titles (Dub
Selected Titles)
6
Repeat step 5 to select all of the titles you
want to dub.
To make adjustments for each of the titles,
select “Settings” (see “To adjust the settings
for each title” below). To cancel all of the
selections, select “Reset,” and go to step 5.
7
Select “Start,” and press ENTER.
The dubbing indication appears in the front
panel display (page 32).
,continued
73
To adjust the settings for each title
You can make detailed settings for each of the
selected titles during Multiple Title Dubbing.
1
In step 6 of “Dubbing multiple titles (Dub
Selected Titles)” on page 73, select “Settings”
and press ENTER.
The following display for making the
adjustments appears.
To re-select titles, select “Change,” and go to
step 5 of “Dubbing multiple titles (Dub
Selected Titles)” above. To have the recorder
adjust the dubbing mode so all of the selected
titles fit in, select “Auto mode.”
To automatically adjust the dubbing mode
(Auto Dub Mode)
If there is not enough available space on the target
disc, the recorder automatically selects a dubbing
mode with lower picture quality according to the
available space. The same dubbing mode is set for
all of the titles. If disc space is insufficient for the
selected dubbing mode, the following display
appears after step 7 of “Dubbing multiple titles
(Dub Selected Titles)” on page 73.
Dub Selected Titles
There is not enough memory. Select
"Auto Dub Mode" or change the selection.
Auto Dub Mode
Dub Selected Titles
2.1GB
Adjust the settings for the dubbing here.
Start
1
World Tour – Asia 1
11.6
Rec Mode: SP
Dub Mode: Fast 0.3GB
Cancel
2
World Tour – Asia 2
18.6
Rec Mode: SP
Dub Mode: Fast 0.3GB
Auto mode
3
World Tour – Asia 3
25.6
Rec Mode: SP
Dub Mode: Fast 0.3GB
4
World Cup Final
Rec Mode: SP
Change
20.6
Dub Mode: Fast 1.2GB
1 Total size of the selected titles
2 Direction of dubbing
3 Available space on the disc to be
dubbed (approximate)
4 Information about the title to be dubbed
(title name, original recording mode,
dubbing mode, and data size after
dubbing)
5 Order of dubbing
74
Change
Cancel
4.6GB
2
Select the title which you want to adjust, and
press ENTER.
The sub-menu appears.
“Dub Mode”: Selects the dubbing mode for
each title (page 70).
“Change Order”: Moves the title to change the
dubbing order. Press M/m to select a new
location, and press ENTER.
“Cancel”: Cancels the title selection. The title
is excluded from dubbing.
3
4
Select an option, and press ENTER.
When you finish making adjustments, select
“Start,” and press ENTER.
Select “Auto Dub Mode” and press ENTER. If
you have selected only one title, select “OK.”
To stop dubbing
Press TOOLS to select “Stop Dubbing,” and press
ENTER. When asked for confirmation, select
“Yes,” and press ENTER.
z Hints
• You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned off.
• You can start Multiple Title Dubbing by selecting
“DUBBING” from the System Menu.
b Notes
DV Dubbing
Before DV Dubbing
This section explains dubbing with a digital video
camera via the DV IN jack on the front panel. If
you want to dub by way of the LINE IN jacks, see
“Recording from connected equipment without a
timer” on page 47.
To record from the DV IN jack
Hookups
DVD recorder
to DV IN
DV Dubbing
The DV IN jack on this recorder conforms to the
i.LINK standard. You can connect any other
equipment that has an i.LINK (DV) jack, and
record digital signals.
Follow the instructions in “Preparing for DV
dubbing,” and then move on to the section on
dubbing. For more information about i.LINK, see
“About i.LINK” on page 101.
• The DV IN jack is for input only. It will not output
signals.
• You cannot use the DV IN jack when:
– your digital video camera does not work with this
recorder. Connect the camera to the LINE IN jack
and follow the instructions of “Recording from
connected equipment without a timer” on page 47.
– the input signal is not in DVC-SD format. Do not
connect a MICRO MV format digital video camera
even if it has an i.LINK jack.
– the images on the tape contain copy protection
signals, which limit recording.
• If you want to play the disc on other DVD equipment,
finalize the disc (page 35).
z Hint
If you plan to do additional editing on a disc after the
initial dub, use the DV IN jack and record on a DVD-RW
(VR mode) or HDD.
i.LINK cable (not supplied)
Preparing for DV dubbing
You can connect a digital video camera to the DV
IN jack on the recorder to record or edit from a
DV/Digital8 format tape. Operation is
straightforward because the recorder will fast
forward and rewind the tape for you – you do not
need to operate your digital video camera. Do the
following to start using the “DV Edit” functions of
this recorder.
See the instruction manual supplied with the
digital video camera as well before connecting.
DV output
Digital video camera
: Signal flow
1
Press HDD or DVD to select the recording
destination.
If you select DVD, insert a disc (see “Inserting
a Disc” on page 25).
2
Insert the source DV/Digital8 format tape
into your digital video camera.
For the recorder to record or edit, your digital
video camera must be set to video playback
mode.
,continued
75
3
Press INPUT SELECT on the remote
repeatedly to select “DV.”
The front panel display changes as follows:
Programme position
4
L1
L2
L3
DV
Press REC MODE on the remote repeatedly
to select the recording mode.
The recording mode changes as follows:
HQ
SEP
HSP
SLP
SP
EP
LSP
LP
For details about the recording mode, see
page 37.
5
Press TOOLS on the remote to select “DV
Audio Input,” and press ENTER. Then,
select the setting for the audio input.
“Stereo1” (default): Records original sound
only. Normally select this when dubbing a DV
format tape.
“Mix”: Records both stereo 1 and 2.
“Stereo2”: Records additional audio only.
Select “Mix” or “Stereo2” only if you have
added a second audio channel when recording
with your digital video camera.
You are ready to start dubbing. Select one of
the dubbing methods on the following pages.
z Hints
• You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned
off.
• You can adjust the settings for the recording picture
before recording. See “Adjusting the recording picture
quality and size” on page 42.
76
b Notes
• You cannot connect more than one piece of digital
video equipment to the recorder.
• You cannot control the recorder using another device
or another recorder of the same model.
• You cannot record date, time, or the contents of the
cassette memory onto the disc.
• If you record from a DV/Digital8 format tape that is
recorded in multiple sound tracks, such as a tape with
multiple sampling frequencies (48 kHz, 44.1 kHz, or
32 kHz), no sound or an unnatural sound will be output
when playing back the sampling frequency switch
point on the disc.
• In order to use this recorder’s “Auto Chapter” setting
(pages 77, 78), be sure to correctly set the clock on your
digital video camera before shooting.
• The recorded picture may be momentarily affected if
the picture size of the source image changes, or if there
is nothing recorded on the tape.
b Notes
Recording an Entire DV
Format Tape (One Touch
Dubbing)
HDD
+RW
-RWVR -RWVideo
+R
• When a blank space between the recordings on the tape
continues for more than five minutes, One Touch
Dubbing ends automatically.
• The recorder records a blank for five minutes before it
stops dubbing. To stop the blank recording, press
x REC STOP.
-R
You can record the entire contents of a DV/
Digital8 format tape onto a disc with a single press
of the ONE-TOUCH DUB button on the recorder.
The recorder controls the digital video camera for
the whole process, and completes the recording.
DV Dubbing
How chapters are created
The contents dubbed to the HDD or DVD become
a single title. When “Auto Chapter” of “Features”
setup is set to “On,” this title is divided into
chapters. When dubbing to the HDD or a DVDRW (VR mode), each shooting session on the tape
becomes a chapter on the disc. For other discs, the
recorder divides the title into chapters at
approximately 6-minute intervals.
Follow steps 1 to 5 of “Preparing for DV
dubbing” on page 75, and press ONE-TOUCH
DUB on the recorder.
The recorder rewinds the tape and then starts
recording the tape contents.
When the recording is finished, the recorder
rewinds the tape in the digital video camera.
To stop during recording
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
z Hints
• If you set “Finalize Disc” of “One Touch Dubbing” to
“Auto” in “Features” setup (page 90), the recorded disc
(except DVD-RW (VR mode)) will automatically be
finalized after recording is finished.
• You can play back a previously recorded title on the
HDD while One Touch Dubbing is in progress.
77
2
Program Edit
HDD
+RW
-RWVR -RWVideo
The display asks if you want to start selecting
scenes.
+R
-R
Scenes Selection
Do you want to select a scene?
You can select scenes from a DV/Digital8 format
tape, and then automatically record selected
scenes to the HDD or a DVD.
Start
Connect your digital video camera and
prepare for recording
m
Select and edit the scenes you want to dub
Using the recorder’s remote control, fast forward
or rewind the tape to select the scenes. At this
point, the selected scenes are not copied to the
disc. The recorder only remembers the IN and
OUT points of the scenes that you selected for
dubbing. You can also reset, erase, or change the
order of the scenes.
m
Dub the selected scenes
After you have selected the scenes, the recorder
will fast forward and rewind the tape
automatically and record the scenes to the HDD or
a DVD.
How chapters are created
The contents dubbed to the HDD or DVD become
a single title. When “Auto Chapter” of “Features”
setup is set to “On,” this title is divided into
chapters. When dubbing to the HDD or a DVDRW (VR mode), each shooting session on the tape
becomes a chapter on the disc. For other discs, the
recorder divides the title into chapters at
approximately 6-minute intervals.
78
Follow steps 1 to 5 of “Preparing for DV
dubbing” on page 75, and press SYSTEM
MENU.
Cancel
• If you have previously saved a programme,
the display asks if you want to edit an
existing programme or to create a new
programme. To resume editing the existing
programme, select “Saved Data,” and go to
step 6.
To use this function, you will do the following:
1
Select “DV EDIT,” and press ENTER.
3
Select “Start,” and press ENTER.
The display for setting the IN point (start of
the scene) appears.
The scene starts to play in the background.
Select scene(Set IN point)
Controlling...
4
Select the IN point by pressing m/M,
and press ENTER.
The display for setting the OUT point (end of
the scene) appears. The scene starts to play in
the background from the IN point.
5
Select the OUT point by pressing m/M,
and press ENTER.
The display asks if you want to add the
selected scene to the Scene List menu.
To preview the scene, select “Preview.”
To reset either the IN or OUT point, select
“Change IN” or “Change OUT,” and repeat
from step 4.
Scenes Selection
Do you want to capture the scene
between IN 0:00:30 and OUT 0:00:52?
OK
Cancel
Preview
Change IN
Change OUT
6
Select “OK,” and press ENTER.
A new Scene List menu appears with the
selected scene.
To add a scene, select “Add.”
DV EDIT
Total 0:00:22
Scenes 1
SCENE LIST
OK
0:00:30-0:00:52
0H00M22S
1
Quit
9
Select “OK,” and press ENTER.
The default title name is fixed, and the display
asks if you want to start recording.
To change the disc media, select “Media” and
press M/m. To change the dubbing mode,
select “Dub Mode” and press M/m.
DV Dubbing
2.6GB
Change the dubbing mode if necessary.
Select "Start" to start dubbing.
Add
Media
Dub Mode
DVD
SP 0.8GB
Start
Cancel
A Thumbnail picture
Data capacity required for the dubbing
B Time information
10 Select “Start,” and press ENTER.
C Total duration of the program
D Total number of scenes
When you finish adding scenes, select the
scene you want to edit, and press ENTER.
The sub-menu appears.
“Move”: Changes the scene order. Follow the
explanations on the screen to change the order
by pressing M/m and ENTER.
“Erase”: Erases the scene. When asked for
confirmation, select “OK.”
“Preview”: Plays the selected scene.
“Change IN”: Changes the start of the scene.
Repeat from step 4.
“Change OUT”: Changes the end of the scene.
Repeat from step 5.
8
When you finish editing the Scene List,
select “OK,” and press ENTER.
The display for entering the title name
appears. To enter a new name, select “Enter,”
and follow the explanations on page 33.
Title Name
Enter the title name.
DV 11.10.03 13:30 - 12.11.03 16:46
OK
Enter
DV Dubbing
7
The recorder starts recording the tape contents
as programmed.
• If the recording does not fit due to the
dubbing mode you selected, the display asks
if you want to continue.
To change the dubbing mode, select “Reset”
and repeat from step 9.
To have the recorder adjust the dubbing
mode, select “Auto Dub Mode.”
• If there is not enough disc space even after
changing the dubbing mode, the display
asks if you want to record halfway.
To continue, select “OK.”
To stop during recording
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
b Notes
• Contents recorded to the HDD or a DVD may not be
recorded as programmed if the tape’s time code is not
sequential or there are blanks between the recordings
on the tape. In this case, see “Recording from
connected equipment without a timer” on page 47.
• The start and end points of a programme may be
different from what you have set if the source DV/
Digital8 format tape is in any of the following
conditions:
– Recording mode was changed during the recording.
– There is a blank space in the recorded portion of the
tape.
• If you set the beginning of the tape as the IN point and
the end point as the OUT point, the IN and OUT points
may move slightly during dubbing.
• You cannot set a scene to be shorter than one second.
79
2
Press PROG +/– to select the programme
position.
Settings and Adjustments
Selected programme position
Aerial Reception and
Language Settings
(Settings)
The “Settings” setup helps you to make tuner,
clock, and programme position settings for the
recorder.
1
2
3
Settings - Channel Setting
Select “Settings,” and press ENTER.
BG
Normal / CATV :
Normal
Channel Set :
C2
Station Name :
3
CDE
Audio :
NICAM
AFT :
On
Settings - Channel Setting
4
The options of “Settings” appear. The default
settings are underlined.
To turn off the display, press SYSTEM
MENU repeatedly.
Prog. 8
Select “System,” and press ENTER.
Press SYSTEM MENU while the recorder is
in stop mode.
Select “SETUP,” and press ENTER.
System :
System :
BG
BG
Normal / CATV :
Normal
DK
Channel Set :
C
I3
Station Name :
AAB
L
Audio :
NICAM
AFT :
On
Prog. 8
Select an available TV system, BG, DK, I, or
L, and press ENTER (page 81).
BG
• Malaysia, Singapore, Thailand
• Middle East
• Australia, New Zealand
DK
Do not select this.
I
• Hong Kong
• South Africa
L
Do not select this.
SETUP
Settings
Channel Setting
Video
Channel List
Audio
TV Guide Page
Features
Clock
Options
Language
Easy Setup
5
Select “Normal/CATV,” and press ENTER.
Settings - Channel Setting
Channel Setting
Presets programme positions manually.
If some programme positions could not be set
using the “Easy Setup” function, you can set them
manually.
If there is no sound or if the picture is distorted, the
wrong tuner system may have been preset during
“Easy Setup.” Set the correct tuner system
manually in the steps below.
1
Select “Channel Setting” in “Settings,” and
press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
C3
Station Name :
80
AAB
Audio :
NICAM
AFT :
On
Prog. 1
System :
BG
Normal / CATV :
Normal
Normal
Channel Set :
3
C
CATV
Station Name :
CDE
Audio :
NICAM
AFT :
On
Prog. 8
6
Select “Normal,” and press ENTER.
To set CATV (Cable Television) channels,
select “CATV.”
7
Select “Channel Set,” and press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
3
C
C2
Station Name :
CDE
Audio :
NICAM
AFT :
On
Prog. 8
8
9
Press M/m repeatedly until the channel you
want is displayed, then press ENTER.
The channels are scanned in the order shown
in the table on page 81.
• If you know the number of the channel you
want, press the number buttons. For
example, for channel 5, first press “0” and
then press “5.” Then press ENTER.
Select “Audio,” and press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
C5
Station Name :
CDE
NICAM
Audio :
NICAM
Standard
AFT :
On
Receivable channels
TV system
Channel coverage
BG
• Malaysia,
Singapore,
Thailand
• Middle East
• Australia, New
Zealand
E2 - E12 VHF
A - H VHF
AS0 - AS12 VHF
NZ1 - NZ11 VHF
E21 - E69 UHF
AS28 - AS69 UHF
Prog. 8
S1 - S20 CATV
S1 - S46 CATV
S21 - S41 HYPER
NICAM
Normally, select this.
Standard
Select this if the sound from
NICAM broadcasts is not
clear.
S01 - S05 CATV
I
• Hong Kong
• South Africa
A - J VHF
4 - 13 VHF
B21 - B69 UHF
S1 - S20 CATV
10 Select “NICAM,” and press ENTER.
11 Select “AFT” and press ENTER.
System :
BG
Normal / CATV :
Normal
Channel Set :
C5
Station Name :
CDE
Audio:
CDE
NICAM
On
AFT :
Off
On
Off
S01 - S05 CATV
Prog. 8
Turns on the Auto Fine
Tuning function. Normally,
select this.
Allows you to adjust the
pictures manually.
12 Select “On” to turn on AFT, and press
ENTER.
• If the Auto Fine Tuning function does not
work effectively, select “Off” and press
ENTER. When the fine tuning bar appears,
press </, to obtain a clearer picture, and
press ENTER.
• To preset another channel, repeat from step
2.
For customers in Australia and New Zealand
• Australia
Channel Set number
Channel
C2
AS0
C3
AS1
C4
AS2
S44
AS3
S46
AS4
S1
AS5
S6
AS5A
C5
AS6
C6
AS7
C7
AS8
C8
AS9
C9
AS9A
C10
AS10
C11
AS11
C12
AS12
C28
AS28
C29
AS29
,continued
Settings and Adjustments
Settings - Channel Setting
S21 - S41 HYPER
81
82
Channel Set number
Channel
Channel Set number
Channel
C30
AS30
C62
AS67
C31
AS31
C63
AS68
C31, C32
AS32
C64
AS69
C32
AS33
S1 - S20
S1 - S20
C33
AS34
C34
AS35
C35
AS36
C36
AS37
C37
AS38
C38
AS39
C38, C39
AS40
C39
AS41
C40
AS42
C41
AS43
C42
AS44
C43
AS45
C44
AS46
C45
AS47
• New Zealand
Channel Set number
Channel
C2
NZ1
C3
NZ2
C4
NZ3
C5
NZ4
C6
NZ5
C7
NZ6
C8
NZ7
C9
NZ8
C10
NZ9
C11
NZ10
C12
NZ11
C21 - C69
E21 - E69
S1 - S46
S1 - S46
C45, C46
AS48
C46
AS49
C47
AS50
Station Name
C48
AS51
C49
AS52
C50
AS53
Changes or enters a new station name (up to 5
characters). The recorder must receive channel
information for station names to appear
automatically.
C51
AS54
1
C52
AS55
C52, C53
AS56
C53
AS57
C54
AS58
C55
AS59
C56
AS60
C57
AS61
C58
AS62
C59
AS63
C59, C60
AS64
C60
AS65
C61
AS66
Select “Channel Setting” in “Settings,” and
press ENTER.
Settings - Channel Setting
System :
BG
Normal / CATV :
Normal
Channel Set :
2
Prog. 1
C3
Station Name :
AAB
Audio :
NICAM
AFT :
On
Press PROG +/– to select the programme
position for which you want to change or enter
a station name.
3
Select “Station Name,” and press ENTER.
The display for entering characters appears.
3
Input Station Name
Press M/m until the selected channel row
moves to the desired programme position.
The selected channel is inserted at the new
programme position.
Settings - Channel List
1
6
"A"
Prog
Channel
Name
2
Back
7
"a"
1
C3
AAB
3
Clear All
8
Symbol
2
C12
3
C21
4
C5
5
C23
6
C24
4
Space
5
9
Cancel
0
Finish
To enter characters, see page 33.
4
Select “Finish,” and press ENTER.
Channel List (Changing/Disabling
the channels)
1
Select “Channel List” in “Settings,” and press
ENTER.
Settings - Channel List
2
Prog
Channel
1
C3
AAB
2
C5
FGH
3
C12
4
C21
5
C23
6
C24
Name
PQR
Press M/m to select the row containing the
programme position you want to change or
disable.
To change, press ENTER and go to step 3.
To disable, press CLEAR and go to step 5.
The disabled positions will be skipped when
you press PROG +/–.
Press ENTER to confirm the setting.
To change or disable the programme position
of another station, repeat from step 2.
b Note
Be sure to correctly select the programme position you
want to disable. If you disable the wrong programme
position by mistake, you need to reset that channel
manually.
TV Guide Page
Some broadcast systems ensure a Teletext
service* in which the complete programmes and
their data (title, date, channel, recording start time,
etc.) are stored day by day. A TV guide page
corresponds to each day of the week. When
recording a programme, the recorder
automatically takes the programme name from the
Teletext pages and stores it as the title name. The
TV guide page numbers depend entirely on the
broadcast itself and may be subject to change. If
so, you may have to set those TV guide page
numbers manually in the TV Guide Page menu.
Settings and Adjustments
Changes or disables the programme positions after
setting the channels. If any programme positions
are unused or contain unwanted channels, you can
disable them.
You can also change station names. If the station
names are not displayed, you can enter them
manually.
4
5
FGH
PQR
* This feature mostly likely cannot be used because it
requires a service that is provided in limited areas only.
1
Select “TV Guide Page” in “Settings,” and
press , or ENTER.
The TV Guide Page menu appears.
To display other pages for programme
positions 7 to 99, press M/m repeatedly.
,continued
83
2
Select the programme position for which you
want to set or change the TV guide page by
pressing PROG +/–.
• The TV guide page numbers (Example:
P301) appear automatically when the
recorder detects them.
Settings - TV Guide Page
Sun
P 301
Mon
P 302
Tue
P 303
Wed
P 304
Thu
P 305
Fri
P 306
Sat
P 307
Prog. 4
• If no page numbers are detected (P000), you
have to set the appropriate TV guide page
number manually.
Settings - TV Guide Page
3
Sun
P 000
Mon
P 000
Tue
P 000
Wed
P 000
Thu
P 000
Fri
P 000
Sat
P 000
Prog. 4
Clock
Select the TV guide page number you want to
modify, and press ENTER.
Settings - TV Guide Page
4
Sun
PP 000
0 0
Mon
P 000
Tue
P 000
Wed
P 000
Thu
P 000
Fri
P 000
Sat
P 000
b Notes
• In step 4 above, enter “000” if you do not want to use
the TV guide page number for automatic labelling. The
recorder will instead store a default title name
(programme position, start time - stop time).
• Refer to the Teletext information on your TV screen to
obtain the TV guide page number with programme
titles and their start times.
• If the Teletext TV guide has a page which always
shows the programmes for the current day, this page
should be input for all days.
• If you start recording more than three minutes before
the programme is scheduled to start, the correct label
information may not be transferred.
• Note that this function may not work correctly with
programmes broadcast from some stations.
• If the broadcast system updates the Teletext
information at the moment recording starts, the title
label may not correspond to the recorded programme.
In this case, you may have to manually enter the correct
title (page 33).
Prog. 4
0
Press the number buttons or </M/m/, to
enter the TV guide page number, and press
ENTER to confirm the setting.
• If you make a mistake, press CLEAR to reenter the correct number.
Auto Adjust (Auto Clock Set)
This function cannot be used in your area.
Present Time (Manual Clock Set)
Set the clock manually.
1
Select “Clock” in “Settings,” and press
ENTER.
2
Select “Present Time,” and press ENTER.
Clock - Present Time
Set the time and date manually.
Sat 1
3
To set or change another TV guide page
number, repeat steps 3 and 4 above.
z Hint
To view Teletext information on your TV screen during
a broadcast, switch to your TV’s tuner by pressing
t TV/VIDEO (page 18).
1
2005
0 : 00
Press M/m to set the day, and press ,.
Set the month, year, hour, and minutes in
sequence. Press </, to select the item to be
set, then press M/m to set the numbers. The
day of the week is set automatically.
To change the numbers, press < to return to
the item to be changed, and press M/m.
4
Press ENTER to start the clock.
z Hint
To change the numbers in step 3, press < to return to the
item to be changed, and select the numbers by pressing
M/m.
84
Language
OSD (On-Screen Display)
Video Settings (Video)
Switches the language for the DVD menu.
Video settings will adjust items related to the
image, such as size and colour.
Choose the settings according to the type of TV,
tuner, or decoder connected to the DVD recorder.
Audio (DVD VIDEO only)
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
Switches the display language on the screen.
DVD Menu (DVD VIDEO only)
Switches the language of the sound track.
When you select “Original,” the language given
priority in the disc is selected.
Subtitle (DVD VIDEO only)
Switches the language of the subtitles recorded on
the disc.
When you select “Audio Follow,” the subtitle
language changes according to the language you
selected for the sound track.
Select “Video,” and press ENTER.
The “Video” setup appears with the following
options. The default settings are underlined.
SETUP
z Hint
If you select “Others” in “DVD Menu,” “Subtitle,” or
“Audio,” select and enter a language code from
“Language Code List” on page 108 using the number
buttons.
TV Type :
16 : 9
Video
Pause Mode :
Auto
Audio
Progressive Mode :
Auto
Features
Line Input
Options
Easy Setup
TV Type
Sets the picture size when playing back a title
recorded from 16:9 size video (page 42) or a 16:9
size commercial DVD video.
Select the playback picture size according to the
type of connected TV (wide-screen/wide mode
TV or conventional 4:3 screen TV).
16:9
Select this when connecting to a
wide-screen TV or TV with a wide
mode function.
4:3 Letter
Box
Select this when connecting to a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the screen.
4:3 Pan
Scan
Select this when connecting to a
4:3 screen TV. Automatically
displays a wide picture on the
entire screen and cuts off the
portions that do not fit.
,continued
Settings and Adjustments
b Note
If you select a language in “DVD Menu,” “Subtitle,” or
“Audio” that is not recorded on the DVD VIDEO, one of
the recorded languages will be automatically selected.
Settings
85
16:9
Auto
Automatically detects the software
type (Film-based or Video-based)
and selects the appropriate
conversion mode. Normally select
this position.
Video
Fixes the conversion mode to the
mode for Video-based software.
4:3 Letter Box
4:3 Pan Scan
b Note
Depending on the disc, “4:3 Letter Box” may be selected
automatically instead of “4:3 Pan Scan” or vice versa.
Pause Mode (HDD/DVDs only)
Selects the picture quality in pause mode.
Auto
Frame
The picture, including subjects
that move dynamically, is output
with no jitter. Normally select this
position.
The picture, including subjects
that do not move dynamically, is
output in high resolution.
Progressive Mode
DVD software can be divided into two types: film
based software and video based software. Video
based software is derived from TV, such as
dramas and sit-coms, and displays images at 30
frames/60 fields (25 frames/50 fields) per second.
Film based software is derived from film and
displays images at 24 frames per second. Some
DVD software contains both Video and Film.
In order for these images to appear natural on your
screen when output in progressive mode (50 or 60
frames per second), the progressive video signal
needs to be converted to match the type of DVD
software that you are watching.
You can fine-tune the progressive 525p/625p
video signal that is output when you press
PROGRESSIVE (“PROGRESSIVE” lights up).
Note that you must connect to a progressive
format TV using the COMPONENT VIDEO OUT
jacks (page 14).
86
Line Input
Sets the method of inputting video signals from
the LINE IN jacks on the rear panel of the
recorder. Select an option for each of the items
below according to the combination of jacks and
methods that you are going to use.
Line1 Input
Selects a method of inputting video signals for the
LINE IN 1 jack on the rear panel of the recorder.
Video
Inputs video signals.
S Video
Inputs S video signals.
Line3 Input
Selects a method of inputting video signals for the
LINE IN 3 jack on the rear panel of the recorder.
The pictures will not be clear if this setting does
not match the type of video input signal.
Video
Inputs video signals.
S Video
Inputs S video signals.
Audio Settings (Audio)
The “Audio” setup allows you to adjust the sound
according to the playback and connection
conditions.
Audio DRC (Dynamic Range Control) (DVDs
only)
Makes the sound clear when the volume is turned
down when playing a DVD that conforms to
“Audio DRC.” This affects the output from the
following jacks:
– LINE OUT R-AUDIO-L jacks
– DIGITAL OUT (OPTICAL or COAXIAL) jack
only when “Dolby Digital” is set to “D-PCM”
(page 88).
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
Standard
Normally select this position.
Select “Audio,” and press ENTER.
TV Mode
Makes low sounds clear even if
you turn the volume down.
Wide
Range
Gives you the feeling of being at a
live performance.
The “Audio” setup appears with the following
options. The default settings are underlined.
SETUP
Settings
Audio ATT :
Off
Video
Audio DRC :
Standard
Audio
Downmix :
Dolby Surround
Features
Audio Connection
Options
Easy Setup
If the playback sound is distorted, set this item to
“On.” The recorder reduces the audio output level.
This function affects the output of the following
jacks:
– LINE OUT R-AUDIO-L jacks
On
Select this when the playback
sound from the speakers is
distorted.
Off
Normally select this position.
Switches the method for mixing down to two
channels when you play a DVD which has rear
sound elements (channels) or is recorded in Dolby
Digital format. For details on the rear signal
components, see “4. Displaying the Playing Time
and Play Information” on page 31. This function
affects the output of the following jacks:
– LINE OUT R-AUDIO-L jacks
– DIGITAL OUT (OPTICAL or COAXIAL) jack
when “Dolby Digital” is set to “D-PCM”
(page 88).
Dolby
Surround
Normally select this position.
Multi-channel audio signals are
output to two channels for
enjoying surround sounds.
Normal
Multi-channel audio signals are
downmixed to two channels for
use with your stereo.
,continued
Settings and Adjustments
Audio ATT (attenuation)
Downmix (DVDs only)
87
Audio Connection
The following setup items switch the method of
outputting audio signals when you connect a
component such as an amplifier (receiver) with a
digital input jack.
For connection details, see “Step 4: Connecting
the Audio Cords” on page 16.
Select “Dolby Digital,” “MPEG,” “DTS,” and
“48kHz/96kHz PCM” after setting “Digital Out”
to “On.”
If you connect a component that does not accept
the selected audio signal, a loud noise (or no
sound) will come out from the speakers, and may
affect your ears or cause speaker damage.
1
Select “Audio Connection” in “Audio,” and
press ENTER.
• MPEG (DVD VIDEO only)
Selects the type of MPEG audio signal.
PCM
Select this when the recorder is
connected to an audio component
without a built-in MPEG decoder.
If you play MPEG audio sound
tracks, the recorder outputs stereo
signals via the DIGITAL OUT
(COAXIAL or OPTICAL) jack.
MPEG
Select this when the recorder is
connected to an audio component
with a built-in MPEG decoder.
• DTS (DVD VIDEO only)
Selects whether or not to output DTS signals.
On
Select this when the recorder is
connected to an audio component
with a built-in DTS decoder.
Off
Select this when the recorder is
connected to an audio component
without a built-in DTS decoder.
Audio - Audio Connection
Digital Out :
2
3
4
On
Dolby Digital :
D-PCM
MPEG :
PCM
DTS :
Off
48kHz/96kHz PCM :
48kHz/16bit
Select “Digital Out,” and press ENTER.
On
Normally select this position.
Off
The influence of the digital
circuit upon the analogue
circuit is minimal.
Select “On,” and press ENTER.
Set the digital output signal.
• Dolby Digital (HDD/DVDs only)
Selects the type of Dolby Digital signal.
88
D-PCM
Select this when the recorder is
connected to an audio component
lacking a built-in Dolby Digital
decoder. The surround effects of
output signals are determined by
the “Downmix” setting item in
“Audio” setup.
Dolby
Digital
Select this when the recorder is
connected to an audio component
with a built-in Dolby Digital
decoder.
• 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
48kHz/
16bit
The DVD video audio signal is
converted to 48kHz/16bit and
output.
96kHz/
24bit
All signals containing 96kHz/
24bit are output without
conversion. However, the signals
are output at 48kHz/16bit if
copyright-protected signals are
contained.
b Notes
• “48kHz/96kHz PCM” setting has no effect when audio
signals are output from the LINE 2 OUT (R-AUDIOL) jacks. If the sampling frequency is 96kHz, signals
are simply converted to 96kHz analog signals and
output.
• When you use the DIGITAL OUT (COAXIAL or
OPTICAL) jack to listen to MPEG audio signals and
set “MPEG” to “MPEG” in “Audio” setup, no sound
will come from your speakers if you select one of the
TVS modes.
b Notes
Recording and Parental
Control Settings (Features)
The “Features” setup allows you to adjust
recording and parental control settings.
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
Select “Features,” and press ENTER.
The “Features” setup appears with the
following options. The default settings are
underlined.
• The actual chapter mark interval may vary depending
on the amount of information contained in the video to
be recorded.
• Chapter marks are automatically inserted where the
recordings start on the tape when “Auto Chapter” is set
to “On” during DV dubbing to the HDD or a DVD-RW
(VR mode).
Parental Control (DVD VIDEO only)
Playback of some DVD VIDEOs can be limited
according to a predetermined level, such as the age
of the users. Scenes may be blocked or replaced
with different scenes.
1
Select “Parental Control” in “Features,” and
press ENTER.
• If you have not entered a password, the
display for registering a new password
appears.
SETUP
Features - Parental Control
Settings
Auto Chapter :
Video
Parental Control
Audio
One Touch Dubbing
Features
Synchro Rec
Record to HDD
Options
HQ Setting
HQ
Colour System
PAL
Screen Saver
On
Enter a new password.
OK
Cancel
• When you have already registered a
password, the display for entering the
password appears.
Auto Chapter
Selects whether to automatically divide a
recording (a title) into chapters during recording
or dubbing.
On
Off
For the HDD or a DVD-RW (VR
mode), the recorder detects
changes in the picture and sound
and automatically inserts chapter
marks.
For other recordable discs, the
recorder inserts chapter marks at
approximately 6-minute intervals.
No chapter mark is inserted.
Features - Parental Control
Enter your password.
Settings and Adjustments
Easy Setup
On
OK
Cancel
2
Enter your four-digit password using the
number buttons, then select “OK” and press
ENTER.
Features - Parental Control
Level :
Off
Standard :
USA
Password
,continued
89
3
Select “Standard,” and press , or ENTER.
The selection items for “Standard” are
displayed.
Features - Parental Control
4
5
Level :
Off
Standard :
USA
USA
Password
Others
Select a geographic area as the playback
limitation level, and press ENTER.
The area is selected.
• When you select “Others,” press the number
buttons to select and enter an area code in
the table (page 108). Then select “OK” and
press ENTER.
Select “Level,” and press ENTER.
The selection items for “Level” are displayed.
One Touch Dubbing
Displays the following options for the One Touch
Dub function.
Finalize Disc (for all recordable discs except
DVD-RW in VR mode)
Selects whether or not to finalize the disc
automatically following One Touch Dubbing
(page 77).
Auto
Automatically finalizes the disc
following One Touch Dubbing.
Manual
Allows you to finalize the disc
manually.
Synchro Rec
Selects the recording destination used for
Synchro-Recording (page 46).
Features - Parental Control
Level :
Off
Standard :
8
Password
7
Record to
HDD
Records to the HDD.
Record to
DVD
Records to DVDs.
6
5
4
The lower the value, the stricter the limitation.
Discs rated higher than the selected level will
be restricted.
6
Select the level, and press ENTER.
The Parental Control setting is complete.
To cancel the Parental Control setting for the
disc, set “Level” to “Off” in step 6.
To change the password, select “Password” in
step 3, and press ENTER. When the display
for registering a password appears, enter a
new four-digit password using the number
buttons, then select “OK” and press ENTER.
b Notes
• If you forget your password, you will have to reset it by
selecting “Parental Control” of “Factory Setup” in
“Options” setup (page 92).
• When you play discs which do not have the Parental
Control function, playback cannot be limited on this
recorder.
• Depending on the disc, you may be asked to change the
Parental Control level while playing the disc. In this
case, enter your password, then change the level.
90
HQ Setting (HDD only)
Selects the HQ mode used for recording on the
HDD (page 37).
HQ+
Records in higher quality
(approximate 15 Mbps).
HQ
Records in the standard HQ mode.
Colour System
Selects the colour system when playing VIDEO
CDs (including Super VIDEO CDs).
PAL
Plays a disc in PAL colour system.
NTSC
Plays a disc in NTSC colour
system.
Screen Saver
The screen saver image appears when you do not
use the recorder for more than 10 minutes while an
on-screen display, such as the System Menu, is
displayed on your TV screen. The screen saver
image helps prevent your display device from
becoming damaged (ghosting).
On
Turns on the screen saver function.
Off
Turns off the function.
b Note
Disc and Remote Control
Settings/Factory Settings
(Options)
The “Options” setup allows you to set up other
operational settings.
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
Select “Options,” and press ENTER.
The “Options” setup appears with the
following options. The default settings are
underlined.
SETUP
Format DVD-RW :
VR
Video
HDD Bilingual Rec. :
Main
Audio
DVD Bilingual Rec. :
Main
Features
Dimmer :
Normal
Options
Power Save :
Off
Auto Display :
On
Command Mode :
DVD3
Easy Setup
Factory Setup
DVD Bilingual Rec. (for all recordable discs
except DVD-RW in VR mode)
Selects the sound to be recorded on the recordable
disc. This setting is not necessary when recording
on DVD-RWs (VR mode) that record both the
main and sub sounds.
Main
Records the main sound for the
bilingual programme.
Sub
Records the sub sound for the
bilingual programme.
Dimmer
Adjusts the lighting of the front panel display.
Normal
Bright lighting.
Power
Save
Low lighting. Turns off the
lighting when the power is off.
b Note
When “Power Save” in “Options” setup is set to “On,”
the front panel display is turned off during standby
regardless of this setting.
Format DVD-RW (DVD-RW only)
Power Save
The recorder automatically starts formatting in
VR mode or Video mode, whichever is selected
below, when a new, unformatted DVD-RW is
inserted.
Selects whether this recorder is in power save
mode when the power is turned off (standby).
VR
Automatically formats the disc in
VR mode.
Video
Automatically formats the disc in
Video mode.
On
Sets to power save mode. The
front panel display is off when the
recorder is in standby.
Off
Does not set to power save mode.
Normally, select this.
Settings and Adjustments
Settings
If you set the recording mode to be changed while
dubbing from a DVD to the HDD, the sound recorded in
the source (DVD) is applied regardless of this setting.
b Note
HDD Bilingual Rec. (HDD only)
Selects the sound to be recorded on the HDD.
Main
Records the main sound for the
bilingual programme.
Sub
Records the sub sound for the
bilingual programme.
Main+Sub
Records the main and sub sounds
for the bilingual programme.
Power Save mode does not function while Synchro
Recording is set, even when “Power Save” is set to “On.”
,continued
91
Auto Display
On
Automatically displays
information on the screen when
the recorder is turned on, etc.
Off
Displays information only when
DISPLAY is pressed.
Command Mode
Changes the Command Mode of the recorder if
other DVD equipment is assigned the same
Command Mode. Be sure to match the Command
Mode switch on the remote to the setting made
here. For details, see “If you have a Sony DVD
player or more than one Sony DVD recorder” on
page 20.
Easy Setup
(Resetting the Recorder)
Select this to run the “Easy Setup” programme.
1
Press SYSTEM MENU while the recorder is
in stop mode.
2
3
Select “SETUP,” and press ENTER.
Select “Easy Setup,” and press ENTER.
SETUP
Settings
Video
Audio
DVD1
DVD2
DVD3
Select this if the default Command
Mode conflicts with other DVD
equipment.
Select this if the default Command
Mode conflicts with other DVD
equipment.
The default Command Mode of
the recorder.
Factory Setup
Allows you to select the setup settings by group,
and return them to their default settings. Note that
all of your previous settings will be lost.
92
1
Select “Factory Setup” in “Options,” and
press , or ENTER.
The display for selecting a group of settings
appears.
2
Select the group of settings you want to return
to default from “Settings,” “Video,” “Audio,”
“Features,” “Options,” “Parental Control,”
and “All,” and press , or ENTER.
3
Select “Start,” and press ENTER.
The selected settings return to their default
settings.
4
Press ENTER when “Finish” appears.
Features
Options
Easy Setup
4
5
6
Easy Setup
Press ENTER.
Select “Start.”
Follow the instructions for “Easy Setup”
(page 21) from step 2.
Additional Information
Troubleshooting
If you experience any of the following difficulties
while using the recorder, use this troubleshooting
guide to help remedy the problem before
requesting repairs. Should any problem persist,
consult your nearest Sony dealer.
Power
The power does not turn on.
, Check that the power cord (mains lead) is
connected securely.
Picture
There is no picture.
Re-connect all connecting cords securely.
The connecting cords are damaged.
Check the connection to your TV (page 13).
Switch the input selector on your TV (such as to
“VCR”) so that the signal from the recorder
appears on the TV screen.
, This recorder cannot record NTSC signals.
, When playing a double-layer DVD, the video
and audio may be momentarily interrupted at the
point where the layers switch.
Picture noise appears.
, If the picture output signal from your recorder
passes through your VCR to get to your TV, or if
you are connected to a combination TV/VIDEO
player, the copy-protection signal applied to
some DVD programmes could affect picture
quality. If you still experience this problem even
when you connect your recorder directly to your
TV, try connecting your recorder to your TV’s S
VIDEO input.
TV programme reception does not fill the
screen.
, Set the channel manually in “Channel Setting” in
“Settings” setup (page 80).
, Select the correct source using the INPUT
SELECT button, or select a channel of any TV
programme using the PROG +/– buttons.
TV programme pictures are distorted.
, Reorient the TV aerial.
, Adjust the picture (see the TV’s instruction
manual).
, Place the recorder and TV farther apart.
, Place the TV and any bunched aerial cables
farther apart.
, The RF cable is connected to the AERIAL OUT
jack on the recorder. Connect the cable to the
AERIAL IN jack.
Additional Information
,
,
,
,
, You have set the recorder to progressive format
(the PROGRESSIVE indicator lights up) even
though your TV cannot accept the progressive
signal. In this case, press PROGRESSIVE until
the PROGRESSIVE indicator turns off.
, Even if your TV is compatible with progressive
format (525p/625p) signals, the image may be
affected when you set the recorder to progressive
format. In this case, press PROGRESSIVE so
that the PROGRESSIVE indicator turns off and
the recorder is set to normal (interlace) format.
, You are playing a DVD recorded in a colour
system that is different from your TV.
, Noise may appear in the pictures recorded on the
HDD, which is due to the characteristics of
HDD, and is not a malfunction.
, When playing a double-layer DVD, the video
and audio may be momentarily interrupted at the
point where the layers switch.
TV channels cannot be changed.
, The channel is disabled (page 83).
, A timer recording started, which changed the
channels.
,continued
93
The picture from equipment connected to the
recorder’s input jack does not appear on the
screen.
, If the equipment is connected to the LINE IN 1
jacks, select “L1” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the LINE 2 IN
jacks, select “L2” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the LINE IN 3
jacks, select “L3” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the DV IN jack,
(this is usually for a digital video camera
connection), select “DV” in the front panel
display by pressing PROG +/– or INPUT
SELECT.
The playback picture or TV programme from
the equipment connected through the recorder
is distorted.
, If the playback picture output from a DVD
player, VCR, or tuner goes through your recorder
before reaching your TV, the copy-protection
signal applied to some programmes could affect
picture quality. Disconnect the playback
equipment in question and connect it directly to
your TV.
The picture does not fill the screen.
, Set “TV Type” in “Video” setup in accordance
with the screen size of your TV (page 85).
The picture does not fill the screen, even
though the picture size is set in “TV Type” in
“Video” setup.
, The picture size of the title is fixed.
94
Sound
There is no sound.
, Re-connect all connections securely.
, The connecting cord is damaged.
, The input source setting on the amplifier or the
connection to the amplifier is incorrect.
, The recorder is in reverse play, fast-forward,
slow motion, or pause mode.
, If the audio signal does not come through the
DIGITAL OUT (OPTICAL or COAXIAL)
jacks, check the “Audio Connection” settings in
“Audio” setup (page 88).
Sound distortion occurs.
, Set “Audio ATT” in “Audio” setup to “On”
(page 87).
Sound is noisy.
, When playing a CD with DTS sound tracks,
noise will come from the LINE OUT R-AUDIOL jacks (page 52).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“Audio DRC” in “Audio” setup to “TV Mode”
(page 87).
, Set “Audio ATT” in “Audio” setup to “Off”
(page 87).
, One of the TVS effects is selected (page 51).
An alternate audio track cannot be recorded.
, When recording from connected equipment, set
“Line Audio Input” in TOOLS menu to
“Bilingual” (page 47).
, Multilingual tracks (main and sub) cannot be
recorded on DVD+RWs, DVD-RWs (Video
mode), DVD+Rs, or DVD-Rs. To record the
language, select “Main” or “Sub” of “DVD
Bilingual Rec.” in “Options” setup before
recording (page 91). To record both the main and
sub sounds, record on a DVD-RW (VR mode).
, Any discs other than the HDD or DVD-RWs
(VR mode) cannot be used for recording both
main and sub sounds. To record on the HDD, set
“HDD Bilingual Rec.” in “Options” setup to
“Main+Sub” (page 91).
, If you have connected an AV amplifier to the
DIGITAL OUT (OPTICAL or COAXIAL) jacks
and want to change the audio track for a DVDRW (VR mode) during playback, set “Dolby
Digital” of “Audio Connection” in “Audio”
setup to “D-PCM” (page 88).
Playback
The recorder does not play any type of disc
(except HDD).
The recorder does not start playback from the
beginning.
, Resume play was activated (page 50).
, You have inserted a DVD whose Title menu or
DVD menu automatically appears on the TV
screen when it is first inserted. Use the menu to
start playback.
The recorder starts playing automatically.
, The DVD VIDEO features an auto playback
function.
, Multilingual tracks are not recorded on the DVD
being played.
, The DVD VIDEO prohibits the changing of the
language for the sound track.
, Try changing the language using the DVD
VIDEO’s menu.
The subtitle language cannot be changed or
turned off.
, Multilingual subtitles are not recorded on the
DVD VIDEO.
, The DVD VIDEO prohibits changing of the
subtitles.
, Try changing the subtitle using the DVD
VIDEO’s menu.
, The subtitles cannot be changed for the titles
recorded on this recorder.
The angles cannot be changed.
, Multi-angles are not recorded on the DVD
VIDEO being played.
, You are trying to change the angles when “
”
does not appear on the TV screen (page 51).
, The DVD VIDEO prohibits changing angles.
, Try changing the angle using the DVD VIDEO’s
menu.
, The angles cannot be changed for the titles
recorded on this recorder.
The MP3 audio tracks do not play.
Additional Information
, The disc is upside down. Insert the disc with the
labelled side facing up.
, The disc is not correctly inserted.
, Moisture has condensed inside the recorder.
Remove the disc and leave the recorder turned on
for about half an hour until the moisture
evaporates.
, If the disc was recorded on another recorder, the
recorder cannot play the disc if it was not
finalized (page 35).
The language for the sound track cannot be
changed.
, The MP3 audio tracks are not recorded in a
format that the recorder can play (page 58).
The JPEG image files do not play.
, The JPEG image files are not recorded in a
format that the recorder can play (page 58).
, Progressive JPEG images cannot be played.
Playback stops automatically.
, If the DVD has an auto pause signal, the recorder
stops playback at the auto pause signal.
TV Pause does not work.
, You are recording to the HDD or the HDD is full.
Some functions such as Stop, Search, or Slowmotion Play cannot be performed.
, Depending on the DVD, you may not be able to
do some of the operations above. See the
instruction manual supplied with the disc.
,continued
95
Recording/Timer recording/
Editing
The programme position cannot be changed
from the programme position you are
recording.
, Set the TV’s input source to “TV.”
Recording does not start immediately after you
press z REC.
, Operate the recorder only after “LOAD,”
“FORMAT,” or “INFOWRITE” disappears
from the front panel display.
Nothing was recorded even though you set the
timer setting correctly.
, There was a power failure during recording.
, The recorder’s internal clock stopped due to a
power failure that lasted for more than 1 hour.
Reset the clock (page 84).
, The channel was disabled after the timer
recording was set. See “Channel Setting” on
page 80.
, Disconnect the power cord (mains lead) from the
mains, and connect it again.
, The programme contains copy protection signals
that restrict copying.
, Other timer setting overlapped the timer setting
(page 45).
, There is no DVD inside the recorder.
, There is not enough disc space for the recording.
, The recorder was in the process of DV Dubbing.
Recording does not stop immediately after you
press x REC STOP.
, It will take a few seconds for the recorder to input
disc data before recording can stop.
Recording does not stop after you press x.
, Open the remote’s cover and press x REC
STOP.
Timer recording is not complete or did not start
from the beginning.
, There was a power failure during recording. If
the power recovers when there is a timer
recording, the recorder resumes recording.
Should the power failure continue for more than
1 hour, reset the clock (page 84).
, Other timer setting overlapped the timer setting
(page 45).
, Disc space was not enough.
Contents previously recorded were erased.
, Data that has been recorded on a DVD with a PC
will be erased from the disc when the disc is
inserted.
, “Auto Title Erase” in the TOOLS menu (appears
when you press TOOLS while the Timer List
menu is turned on) is set to “On” (page 45).
, The title was updated and recorded over
(page 39).
Recording from the equipment
with a timer
Nothing was recorded even though you set the
Synchro-Rec setting correctly.
, You forgot to turn off the connected equipment.
Turn off the connected equipment and set the
recorder to Synchro-Rec standby mode
(page 46).
, The recorder was not set to the SynchroRecording standby mode. Press SYNCHRO
REC to have the recorder stand by for recording.
Make sure the SYNCHRO REC indicator lights
up on the front panel (page 46).
, The recorder is connected to the TV output jack
of the connected equipment.
Synchro-Recording does not complete.
, The timer setting for the connected equipment
overlapped the recorder’s timer setting
(page 47).
, There was a power failure during the recording.
The recorder automatically starts recording
when the satellite receiver is turned on.
, The Synchro-Rec function was activated. Turn
off the satellite receiver and cancel the SynchroRec function (page 46).
96
Display
The clock has stopped.
, Set the clock again (page 84).
, The clock stopped due to a power failure that
lasted for more than 1 hour. Reset the clock
(page 84).
The TIMER REC indicator is flashing.
, The disc does not have enough space.
, Insert a recordable disc inside the recorder.
The recording mode indication is incorrect.
, When the recording or dubbing is less than three
minutes, the recording mode indication may be
displayed incorrectly. The actual recording itself
is correctly made in the selected recording mode.
, After playing titles recorded in SLP and SEP
mode, the recording mode indication may
change depending on the recorded programme.
The clock does not appear in the front panel
display.
, The same command mode is set for both the
equipment and recorder. Set a different
command mode for the recorder (page 20).
Others
The recorder does not operate properly.
, Restart the recorder. Press down [/1 on the
recorder for more than ten seconds until
“WELCOME” appears in the front panel display.
, When static electricity, etc., causes the recorder
to operate abnormally, turn off the recorder and
wait until the clock appears in the front panel
display. Then, unplug the recorder and after
leaving it off for a while, plug it in again.
Five numbers or letters are displayed in the
front panel display.
, The self-diagnosis function was activated (see
the table on page 98).
The disc tray does not open after you press Z
(open/close).
, It may take a few seconds for the disc tray to
open after you have recorded or edited a DVD.
This is because the recorder is adding disc data to
the disc.
Remote control
The remote does not function.
, Batteries are weak.
, The remote is too far from the recorder.
, The remote’s manufacturer code returned to the
default setting when you replaced the batteries.
Reset the code (page 18).
, Turn on the recorder.
, The remote is not pointed at the remote sensor on
the recorder.
, Different command modes are set for the
recorder and remote. Set the same command
mode (page 20). The default command mode
setting for this recorder and the supplied remote
is DVD3.
, Set the TV/DVD switch to DVD (page 19).
The disc tray does not open and “TRAY
LOCKED” appears in the front panel display.
Additional Information
, “Dimmer” in “Options” setup is set to “Power
Save” (page 91).
, The “Power Save” in “Options” setup was set to
“On,” and the recorder is in standby (page 91).
Other Sony equipment responds to the remote.
, Contact your Sony dealer or local authorized
Sony service facility.
“RECOVERY” appears in the front panel
display.
, The recorder’s recovery function was activated
when the recorder was turned on because the
power was turned off or failed during recording.
Leave the recorder on until “RECOVERY”
disappears from the front panel display.
,continued
97
“HDD ERROR” appears in the front panel
display.
, The hard disk error occurred. Press down @/1 on
the recorder for ten seconds until “WELCOME”
appears in the front panel display. If this does not
resolve the problem, format the recorder’s HDD
by pressing down the HDD button on the
recorder for more than ten seconds until
“FORMAT” appears in the front panel display.
Note that all the contents recorded on the HDD
will be erased. If this does not fix the problem,
contact your nearest Sony dealer.
“FAN ERROR” appears in the front panel
display.
, Check that the vent on the rear of the recorder is
not blocked. Then, immediately disconnect the
AC power cord (mains lead). Leave the recorder
off for a while, then re-connect the power cord
(mains lead), and press [/1 on the recorder.
The disc tray does not open and you cannot
remove the disc after you press Z (open/
close).
, Turn off the recorder. Once the clock appears in
the front panel display, disconnect the power
cord (mains lead). (If the recorder does not turn
off or if the clock does not appear in the front
panel display, disconnect the power cord (mains
lead) anyway.) Connect the power cord (mains
lead) again while pressing down A on the
recorder, and release the button when the disc
tray opens. Then, keep [/1 on the recorder
pressed for about ten seconds until
“WELCOME” appears in the front panel display.
“LOCKED” appears in the front panel display.
, The disc tray is locked. Cancel the Child Lock
(page 50).
98
Self-diagnosis Function
(When letters/numbers
appear in the display)
When the self-diagnosis function is activated to
prevent the recorder from malfunctioning, a fivecharacter service number (e.g., C 13 00) with a
combination of a letter and four numbers appears
in the front panel display. In this case, check the
following table.
First three
characters of
the service
number
Cause and/or corrective
action
C 13
There is a problem in the HDD.
, Contact your nearest Sony
dealer or local authorized
service facility.
The DVD is dirty.
, Clean the disc with a soft
cloth.
C 31
The DVD/CD is not inserted
correctly.
, Re-insert the disc correctly.
E XX
(xx is a number)
To prevent a malfunction, the
recorder has performed the selfdiagnosis function.
, Contact your nearest Sony
dealer or local authorized
Sony service facility and
give the five-character
service number.
Example: E 61 10
On cleaning discs
Notes About This Recorder
Do not use a commercially available cleaning
disc. It may cause a malfunction.
On operation
Notes about the discs
• If the recorder is brought directly from a cold to
a warm location, or is placed in a very damp
room, moisture may condense on the lenses
inside the recorder. Should this occur, the
recorder may not operate properly. In this case,
remove the disc and leave the recorder turned on
for about half an hour until the moisture
evaporates.
• When you move the recorder, take out any discs.
If you don’t, the disc may be damaged.
On adjusting volume
Do not turn up the volume while listening to a
section with very low level inputs or no audio
signals. If you do, the speakers may be damaged
when a peak level section is played.
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface. Dust,
fingerprints, or scratches on the disc may cause
it to malfunction.
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, or leave it in a car
parked in direct sunlight as the temperature may
rise considerably inside the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth. Wipe the
disc from the centre out.
On cleaning
About repairing the hard disk drive
• It may be necessary to access data stored on the
hard disk for testing purposes; there is no
intention to copy or store the data, titles or any
other information.
• If replacement or initialization (format) is
required, the hard disk will be formatted at our
discretion. In this case, please note that all of the
contents recorded there will be erased (including
any data found to violate copyright law).
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
• Do not use the following discs.
– A disc that has a non-standard shape (e.g.,
card, heart).
– A disc with a label or sticker on it.
– A disc that has cellophane tape or sticker
adhesive on it.
Additional Information
Clean the cabinet, panel, and controls with a soft
cloth slightly moistened with a mild detergent
solution. Do not use any type of abrasive pad,
scouring powder or solvent such as alcohol or
benzine.
99
General
Specifications
System
Laser: Semiconductor laser
Channel coverage:
PAL/SECAM (B/G, D/K, I, L)
VHF: E2 to E12, R1 to R12, F2 to F10, Italian
A to H, Ireland A to J, South Africa 4 to 13/
UHF: E21 to E69, R21 to R69, B21 to B69,
F21 to F69/CATV: S01 to S05, S1 to S20,
France B to Q/HYPER: S21 to S41
For details, see “Receivable channels” (page 81).
The above channel coverage merely ensures the
channel reception within these ranges. It does not
guarantee the ability to receive signals in all
circumstances.
Video reception: Frequency synthesizer system
Audio reception: Split carrier system
Aerial out: 75-ohm asymmetrical aerial socket
Timer: Clock: Quartz locked/Timer indication:
24-hour cycle (digital)/Power back-up
duration: 1 hour
Video recording format: MPEG Video
Audio recording format/applicable bit
rate: Dolby Digital 2 ch/256 kbps
Inputs and outputs
LINE OUT
(AUDIO): Phono jack/2 Vrms/10 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y:1.0 Vp-p,
C: 0.3 Vp-p (PAL)
LINE IN 1/2/3
(AUDIO): Phono jack/2 Vrms/more than
22 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y:1.0 Vp-p,
C: 0.3 Vp-p (PAL)
DV IN: 4-pin/i.LINK S100
DIGITAL OUT (OPTICAL): Optical output jack/
–18 dBm (wave length: 660 nm)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT
(Y, PB/CB, PR/CR):
Phono jack/Y: 1.0 Vp-p, PB/CB: 0.7 Vp-p,
PR/CR: 0.7 Vp-p
100
Power requirements: 220-240 V AC, 50/
60 Hz
Power consumption:
RDR-HX710: 51 W
RDR-HX910: 55 W
Dimensions (approx.): 430 × 75 × 328 mm
(width/height/depth) incl. projecting parts
Hard disk drive capacity:
RDR-HX710: 160 GB
RDR-HX910: 250 GB
Mass (approx.): 5.0 kg
Operating temperature: 5ºC to 35ºC
Operating humidity: 25% to 80%
Supplied accessories:
Audio/video cord (1)
Power cord (mains lead) (1)
Aerial cable (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
Specifications and design are subject to change
without notice.
Compatible colour systems
This recorder is designed to record using the PAL
colour system and play back using the PAL or
NTSC colour systems.
The signals of the SECAM colour system can be
received or recorded but played back in the PAL
colour system only. Recording of video sources
based on other colour systems cannot be
guaranteed.
About i.LINK
The DV IN jack on this recorder is an i.LINKcompliant DV IN jack. This section describes the
i.LINK standard and its features.
What is i.LINK?
b Note
Normally, only one piece of equipment can be connected
to this recorder by the i.LINK cable (DV connecting
cable). When connecting this recorder to i.LINKcompatible equipment having two or more i.LINK jacks
(DV jacks), see the instruction manual of the equipment
to be connected.
About the name “i.LINK”
i.LINK is a more familiar term for IEEE 1394 data
transport bus proposed by SONY, and is a
trademark approved by many corporations.
IEEE 1394 is an international standard
standardized by the Institute of Electrical and
Electronics Engineers.
i.LINK’s maximum baud rate varies according to
the equipment. Three maximum baud rates are
defined:
S100 (approx. 100 Mbps*)
S200 (approx. 200 Mbps)
S400 (approx. 400 Mbps)
The baud rate is listed under “Specifications” in
the instruction manual of each equipment. It is
also indicated near the i.LINK jack on some
equipment.
The maximum baud rate of equipment on which it
is not indicated such as this unit is “S100.”
When units are connected to equipment having a
different maximum baud rate, the baud rate
sometimes differs from the indicated baud rate.
* What is Mbps?
Mbps stands for megabits per second, or the amount of
data that can be sent or received in one second. For
example, a baud rate of 100 Mbps means that 100
megabits of data can be sent in one second.
i.LINK functions on this recorder
For details on how to dub when this recorder is
connected to other video equipment having DV
jacks, see page 75.
The DV jack on this recorder can only input DVCSD signals. It cannot output signals. The DV jack
will not accept MICRO MV signals from
equipment such as a MICRO MV digital video
camera with an i.LINK jack.
For further precautions, see the notes on page 75.
For details on precautions when connecting this
recorder, also see the instruction manuals for the
equipment to be connected.
Additional Information
i.LINK is a digital serial interface for handling
digital video, digital audio and other data in two
directions between equipment having the i.LINK
jack, and for controlling other equipment.
i.LINK-compatible equipment can be connected
by a single i.LINK cable. Possible applications are
operations and data transactions with various
digital AV equipment. When two or more i.LINKcompatible equipment are connected to this
recorder in a daisy chain, operations and data
transactions are possible with not only the
equipment that this recorder is connected to but
also with other devices via the directly connected
equipment.
Note, however, that the method of operation
sometimes varies according to the characteristics
and specifications of the equipment to be
connected, and that operations and data
transactions are sometimes not possible on some
connected equipment.
i.LINK baud rate
Required i.LINK cable
Use the Sony i.LINK 4-pin-to-4-pin cable (during
DV dubbing).
i.LINK and
are trademarks.
101
Guide to Parts and Controls
For more information, see the pages in parentheses.
Remote
A TV/DVD switch (18)
B Z (open/close) button (25)
C [/1 (on/standby) button (21)
1
2
3
4
5
6
7
8
9
0
D HDD button (27)
DVD button (25)
E PROG (programme) +/– buttons (27)
The + button has a tactile dot*.
F Number buttons (41, 56)
SET button (41)
The number 5 button has a tactile dot*.
G
2 (volume) +/– buttons (18)
H CLEAR/-/-- (ten digit) button (41)
I
(audio) button (51)
(subtitle) button (51)
The
(audio) button has a tactile dot*.
J INPUT SELECT button (47, 75)
t TV/VIDEO button (18)
K DISPLAY button (31)
TIME/TEXT button (31)
L [TIMER] button (39, 41)
M SUR (surround) button (51)
N SYSTEM MENU button (78, 80)
TITLE LIST button (28, 49, 58, 63)
TIMER LIST button (44)
O TOP MENU button (49)
P MENU button (49)
Q </M/m/,/ENTER button (21)
R O RETURN button (44)
S TOOLS button (25)
T
(instant replay)/
buttons (28, 58)
(instant advance)
U ./> (previous/next) buttons (51)
V mc
(51)
102
/
CM (search) buttons
W VISUAL SEARCH button (56)
X H (play) button (49)
X (pause) button (51)
x (stop) button (49)
The H button has a tactile dot*.
Y z REC button (27)
X REC PAUSE button (27)
x REC STOP button (27)
Z REC MODE button (27)
wj CHAPTER MARK/CHAPTER MARK
ERASE buttons (67)
wk SYNCHRO REC button (46)
wl
(wide mode) button (18)
e;
(angle) button (51)
ea COMMAND MODE switch (DVD 1,2,3)
(20)
es PROGRESSIVE button (15)
* Use the tactile dot as a reference when operating the
recorder.
Additional Information
,continued
103
Front panel
A [/1 (on/standby) button (21)
J
B Front panel display (32, 105)
K ONE-TOUCH DUB button (77)
C Disc tray (25)
L SYSTEM MENU button (78, 80)
D TIMER REC indicator (39)
SYNCHRO REC indicator (46)
M TOOLS button (25)
E A (open/close) button (25)
O O RETURN button (44)
F HDD button/indicator (27)
DVD button/indicator (25)
G
(remote sensor) (18)
H H (play) button (49)
X (pause) button (51)
x (stop) button (49)
I z REC button (27)
X REC PAUSE button (27)
x REC STOP button (27)
104
DV IN jack (75)
N </M/m/,/ENTER button (21)
P ./> (previous/next) buttons (51)
Q PROGRAM +/– buttons (27)
The + button has a tactile dot*.
R INPUT SELECT button (47, 75)
S REC MODE button (37)
T LINE 2 IN (S VIDEO/VIDEO/L(MONO)
AUDIO R) jacks (22)
* Use the tactile dot as a reference when operating the
recorder.
Front panel display
HDD
DVD RW
VR
DVD
VCD
NICAM
PROGRESSIVE
A HDD/DVD indicators
Displays the selected media and the
playing/recording/dubbing status.
E Displays the following (32):
•
•
•
•
•
B Disc type*/recording format
C NICAM indicator (38)
Playing time/remaining time
Current title/chapter/track/index number
Recording time/recording mode
Clock
Programme position
F
D Audio signal indicators (31)
(angle) indicator (51)
G PROGRESSIVE indicator (15)
* Displays DATA CDs as “CD.”
Rear panel
AERIAL
IN
DIGITAL
OUT
PCM/DTS/MPEG/
DOLBY DIGITAL
COAXIAL
Additional Information
z Hint
You can turn off the front panel display when the recorder is turned off by setting “Dimmer” to “Power Save” in
“Options” setup (page 91).
COMPONENT
VIDEO OUT
LINE IN
R-AUDIO-L
Y
VIDEO
S VIDEO
1
3
OUT
LINE OUT
R-AUDIO-L
VIDEO
S VIDEO
PB/CB
PR/CR
~ AC IN
OPTICAL
A AERIAL IN/OUT jacks (13)
B COMPONENT VIDEO OUT (Y, PB/CB,
PR/CR) jacks (14)
C AC IN terminal (17)
D LINE OUT (S VIDEO) jack (14)
E LINE OUT (R-AUDIO-L/VIDEO) jacks
(14, 16)
F LINE IN 1/3 (S VIDEO) jack (22)
G LINE IN 1/3 (R-AUDIO-L/VIDEO) jacks
(22)
H DIGITAL OUT (COAXIAL/OPTICAL)
jacks (16)
105
Glossary
Chapter (page 56)
Sections of a picture or a music feature that are
smaller than titles. A title is composed of several
chapters. Depending on the disc, no chapters may
be recorded.
Copy protection signals (page 38)
Copy restriction set by copyright owners, etc.
These signals are included in some software or TV
programmes and restrict recording on this
recorder.
Dolby Digital (page 88)
Digital audio compression technology developed
by Dolby Laboratories. This technology conforms
to multi-channel surround sound. The rear channel
is stereo and there is a discrete subwoofer channel
in this format. Dolby Digital provides the same
discrete channels of high quality digital audio
found in “Dolby Digital” theater surround sound
systems.
Good channel separation is realized because all of
the channel data is recorded discretely, and little
deterioration occurs because all channel data
processing is digital.
DTS (page 88)
Digital audio compression technology by Digital
Theater Systems, Inc. This technology conforms
to multi-channel surround sound. The rear channel
is stereo and there is a discrete subwoofer channel
in this format. DTS provides the same discrete
channels of high quality digital audio.
Good channel separation is realized because all of
the channel data is recorded discretely, and little
deterioration occurs because all channel data
processing is digital.
DVD+R (page 8)
A DVD+R (read “plus R”) is a recordable disc that
is the same size as a DVD VIDEO. Contents can
be recorded only once to a DVD+R, and will have
the same format as a DVD VIDEO.
106
DVD+RW (page 8)
A DVD+RW (read “plus RW”) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
DVD-R (page 8)
A DVD-R is a recordable disc that is the same size
as a DVD VIDEO. Contents can be recorded only
once to a DVD-R, and will have the same format
as a DVD VIDEO.
DVD-RW (page 8)
A DVD-RW is a recordable and rewritable disc
that is the same size as a DVD VIDEO. The DVDRW has two different modes: VR mode and Video
mode. DVDs created in Video mode have the
same format as a DVD VIDEO, while discs
created in VR (Video Recording) mode allow the
contents to be programmed or edited.
DVD VIDEO (page 10)
A disc that contains up to eight hours of moving
pictures on a disc the same diameter as a CD.
The data capacity of a single-layer and singlesided DVD is 4.7 GB (Giga Byte), which is 7
times that of a CD. The data capacity of a doublelayer and single-sided DVD is 8.5 GB, a singlelayer and double-sided DVD is 9.4 GB, and
double-layer and double-sided DVD is 17 GB.
The picture data uses the MPEG 2 format, which
is a worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 (average) of its original size. The DVD
also uses a variable rate coding technology that
changes the data to be allocated according to the
status of the picture. Audio information is
recorded in a multi-channel format, such as Dolby
Digital, allowing you to enjoy a more real audio
presence.
Furthermore, various advanced functions such as
the multi-angle, multilingual, and Parental
Control functions are provided on the DVD.
Hard disk drive (page 2)
A hard disk drive is a whole mechanical system
that consists of disks and drive. Disks are flat,
circular, rigid plates coated with a thin magnetic
media. Magnetic heads record data on the rapidly
spinning disks, and this enables the speedy and
efficient reading and writing of data.
Interlace format (page 15)
Interlace format shows every other line of an
image as a single “field” and is the standard
method for displaying images on television. The
even number field shows the even numbered lines
of an image, and the odd numbered field shows the
odd numbered lines of an image.
MPEG Audio (page 88)
International standard coding system used to
compress audio digital signals authorized by ISO/
IEC. MPEG 2, used on DVDs, conforms to up to
7.1-channel surround.
Original (page 62)
Titles actually recorded on a HDD/DVD-RW (VR
mode). Erasing original titles frees up disc space.
Playlist (page 62)
Progressive format (page 15)
Compared to the Interlace format that alternately
shows every other line of an image (field) to create
one frame, the Progressive format shows the entire
image at once as a single frame. This means that
while the Interlace format can show 25-30 frames/
50-60 fields in one second, the Progressive format
can show 50/60 frames in one second. The overall
picture quality increases and still images, text, and
horizontal lines appear sharper.
Additional Information
Playback information created from the actual
recordings on a HDD/DVD-RW (VR mode). A
Playlist leaves the original titles as they are, and
contains only the information needed to control
playback. A Playlist title takes up very little disc
space.
Title (page 56)
The longest section of a picture or music feature
on a DVD, movie, etc., in video software, or the
entire album in audio software.
Track (page 56)
Sections of a music feature on a CD/VIDEO CD
(the length of a song).
107
Language Code List
For details, see page 85.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1183
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian;
Lettish
1345 Malagasy
1347
1349
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1507
1508
1509
1511
1512
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
Code Area
Code Area
Code Area
Code Area
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2248
2238
2254
2276
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2528
2184
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali;
Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
1436
1463
1481
1482
1483
1489
1491
1495
1498
1501
1502
1503
1505
1506
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan)Oromo
Oriya
Punjabi
Polish
Pashto;
Pushto
Portuguese
Quechua
RhaetoRomance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
SerboCroatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volap k
Wolof
Xhosa
Yoruba
Chinese
Zulu
1703 Not specified
Area Code
For details, see page 89.
108
Argentina
Australia
Austria
Belgium
Brazil
Canada
Chile
China
Denmark
Finland
France
Germany
India
Indonesia
Italy
Japan
Korea
Malaysia
Mexico
Netherlands
New Zealand
Norway
Pakistan
Philippines
Portugal
Russia
Singapore
Spain
Sweden
Switzerland
Thailand
United
Kingdom
Index
Words in quotations appear in
the on-screen displays.
Numerics
16:9 21, 85
4:3 Letter Box 21, 85
4:3 Pan Scan 21, 85
“48kHz/96kHz PCM” 88
A
“A-B Erase” 64
Adjusting
playback picture 53
playback sound 54
recording picture 42
Aerial 13
“AFT” 81
Album 31, 61
Album number 31
“Album Search” 57
Angle 51
Area code 108
“Audio” 85
Audio 51, 87
“Audio Connection” 21
Audio cord 16
“Audio DRC” 87
“Audio Filter” 54
“Audio Settings” 54
“Auto Chapter” 89
Auto Clock Set 84
“Auto Display” 92
“Auto Title Erase” 45
“AV SYNC” 54
B
Batteries 18
“Bilingual” 46, 47
Bilingual recording 38
“BNR” 53
“Brightness” 43, 53
C
D
“C NR” 53
“Capture” 67
“Capture All” 67
“CATV” 80
CD 10
“Change IN” 68, 79
“Change OUT” 68, 79
“Channel List” 83
“Channel Setting” 80
Chapter 31, 43, 67, 106
CHAPTER MARK 67
CHAPTER MARK ERASE
67
Chapter number 31
“Chapter Search” 57
Chasing Playback 55
“Check Overlap” 45
Checking/changing/
cancelling timer settings
(Timer List) 44
Child Lock 50
Cleaning discs 99
Clock 21, 84
“Colour” 43, 53
“Colour System” 90
Colour systems 100
“Combine” 69
“Command Mode” 20, 92
Component video input 14
COMPONENT VIDEO OUT
14
Connecting 14
the aerial cable 13
the audio cords 16
the video cords 14
“Contrast” 43, 53
Controlling TVs with the
remote 18
Copy control signals 38
Copy protection 106
Copy-Free 38
Copy-Never 38
Copy-Once 38
CPRM 8
“Create Playlist” 67
Creating chapters 67
DATA CD 10
“Digital Out” 88
Digital video camera 75
“Dimmer” 91
“Disc Info” 25, 34, 66
Disc Map 66
Disc Settings 25, 34, 66, 91
Disc space 26
Disc types 8
Display
front panel display 32,
105
“Divide” 65
Dolby Digital 16, 88, 106
“Downmix” 87
DTS 88, 106
“Dub Mode” 70, 79
Dubbing
“Dub Mode” 70
High-speed Dubbing 70
Rec Mode Conversion
Dubbing 71
“Settings” 74
“DV Audio Input” 76
DV Dubbing 75
One Touch Dubbing 77,
90
Program Edit 78
“DV EDIT” 78
DV IN 75
“DVD Bilingual Rec.” 91
“DVD Menu” 85
“DVD Rec. Picture Size” 43
DVD VIDEO 10, 106
DVD+R 8, 106
DVD+RW 8, 106
DVD-R 8, 106
DVD-RW 8, 106
DVD-RWs (Video mode) 63
“DVE” 53
,continued
109
E
L
Easy Setup 21, 92
Editing 62, 67
DV Edit 75
Enter characters 33
“Erase” 44, 63, 68, 79
“Erase All” 66
“Erase Titles” 65
“Extend Rec” 40
Labelling 34
Language 85
LINE 2 IN 23
“Line Audio Input” 46, 47
LINE IN 1 or 3 22
“Line Input” 86
“Line1 Input” 86
“Line3 Input” 86
F
M
“Factory Setup” 92
“Features” 89
“File Search” 57
“Finalize” 36
“Finalize Disc” 90
Finalizing 35, 36
“Format” 25
“Format DVD-RW” 91
Formatting 25
Freeze Frame 52
Front panel 104
Front panel display 32, 105
Manual Clock Set 84
MENU 49
Menu
DVD’s Menu 49
Top menu 49
“Mix” 76
“MNR” 53
“Modify” 44
“Move” 68, 79
MP3 audio tracks 58
MPEG 88, 107
G
GB 26
G-Code 41
NICAM 38, 81
“Normal” 80
Number buttons 34, 41
H
O
Handling discs 99
“HDD Bilingual Rec.” 91
“Hue” 53
One Touch Dubbing 77, 90
On-screen display
“OSD” language 21, 85
“Options” 91
Original 29, 62, 107
I
i.LINK 101
INPUT SELECT 47, 76
Interlace 15, 107
Interlace format 107
J
JPEG image files 58
110
N
P
Page mode 29
Parental Control 50, 89
Parts and controls 102
“Pause Mode” 86
“PB Video Equalizer” 53
PBC 49
Picture quality 42, 53
Picture size 42
“Play Beginning” 50
Play mode 31
Playable discs 10
Playback 10, 31, 49, 51, 52
fast forward 52
fast reverse 52
freeze frame 52
instant advance 51
instant replay 51
JPEG image files 58
MP3 audio tracks 58
resume play 50
scan audio 50
slow-motion play 52
Playing status bar 31
Playlist 29, 62, 67, 107
Power cord (mains lead) 17
“Power Save” 91
“Preview” 68, 79
Program Edit 78
Progressive 15, 107
“Progressive Mode” 86
“Protect” 63
“Protect Disc” 35
Protection
disc 34
title 63
Q
Quick guide to disc types 8
Quick Timer 42
R
Rear panel 105
REC 27
“Rec Mode” 42
Rec Mode Adjust 40
“Rec NR” 43
REC PAUSE 27
“Rec Settings” 42
REC STOP 77
“Rec Video Equalizer” 43
Recordable discs 8
Recording 37, 46, 89
picture adjustment 42
recording format 8
recording mode 28, 37
recording time 28
“Update” 39
while watching another
programme 27
Recording time 37
RECOVERY 97
Region code 11
Remaining time 31
Remote 18, 102
Resetting the recorder 92
Resume Play 50
S
S VIDEO 14
Scan Audio 50
Scene List 68
Screen Saver 90
“Search” 57
Searching
fast reverse/fast forward
51
locating the beginning of
the title/chapter/
track 51
scan audio 50
search mode 56
visual search 56
SET 19, 34
“Set Thumbnail” 64
“Settings” 80
Simultaneous Rec and Play 55
Slow-motion play 52
Sort 30
Sound quality 54
“Station Name” 83
“Stereo1” 76
“Stereo2” 76
Subtitle 51, 85
Super VIDEO CD 10
Surround 51
Synchro Rec 46
“System” 80
T
Teletext 27, 83
Thumbnail picture 30
“Time Search” 57
TIME/TEXT 32
TIMER 39
Timer List 44
Timer recording
check/change/cancel 44
G-Code 41
manual setting 39
Rec Mode Adjust 40
Synchro Rec 46
Title 31, 107
TITLE LIST 49
Title List 28, 49
Sort 30
Thumbnail 30
“Title Name” 64
Title number 31
“Title Search” 57
TOP MENU 49
Track 107
“Track Search” 57
Troubleshooting 93
Tuner System 21
“TV Guide Page” 83
TV Pause 54
TV system 80
“TV Type” 21, 85
TV/DVD switch 18
TV/VIDEO 27
TVS (TV Virtual Surround)
51
U
“Unfinalize” 36
Unfinalizing 36
Usable discs 8, 10
V
“Video” 85
VIDEO CD 10
Video cord 14
Video input 14
Video mode 8
“Video Settings” 53
Visual Search 56
VR mode 8, 62
Y
“Y NR” 53
Z
ZWEITON 38
111
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Sony Corporation Printed in Malaysia
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement