Sony RM-V202A User's manual

Sony RM-V202A User's manual
2-050-358-11(1)
RM-V202A
Remote Commander
Searching for the Correct Code
If you have tried all the code numbers listed for your component and
you still cannot get the Commander to work (or if your component is
not listed in the “Component code numbers” table), try these steps.
Operating Instructions
使用說明書
© 2004 Sony Corporation
Before starting the Search function
Printed in China
Set each component to the following status to enable the Search function.
TV: power-on
Other components: power-off
English
Setting Up the Remote Commander
About Presetting the Commander
The Commander is preset at the factory to operate Sony brand
components.
If you are using the Commander with a Sony component, you will
not need to preset the Commander before you start using it.
To set up the Commander to use with other (non-Sony) manufacturers’
components, or to use with a component that is not preset at the
factory, you will need to follow the instructions in this manual to preset
the Commander with the correct code number for your component(s).
(See the supplied “Component code numbers” table also.)
Component that can be preset Button Factory setting
TV
VCR/Cable box/DVD/TV
TV
VCR
CBL
DVD
Sony TV
Sony VHS VCR (VTR3)
—
Sony DVD player
Notes
• The Commander can be set up to operate only one component per
button – unless their code numbers happen to be the same. For
example, you cannot set up the Commander to operate a Sony TV
and a Panasonic TV simultaneously (because they use different
code numbers).
• You may not be able to operate even a Sony brand component with
the factory presetting. In such a case, follow the procedure in
“Setting the Code.”
Installing the Batteries
Before replacing the batteries, have new ones ready
beforehand.
Slide open the battery compartment and insert two size AA (R6)
batteries (not supplied).
Be sure to line up the + and – on the batteries with the + and – on the
battery compartment.
1
Notes on Using the Remote Commander
• If after trying all the codes listed for your component you still
cannot get the Commander to work properly, try the search
method described in “Searching for the Correct Code.”
2
• If the electrolyte inside the battery should leak, wipe the
contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the electrolyte
from leaking, remove the batteries when you plan not to use the
Commander for a long period of time.
• Replace both batteries with new ones.
• Do not take more than 3 minutes to replace the batteries; otherwise,
your code number settings will be erased.
Notes on Batteries
• Do not mix old batteries with new ones or mix different types of
batteries together.
1 button.
4 Repeat step 3 until the correct code number is found.
Follow steps 1 and 2 below for each component you plan to use with
the Commander.
Keep trying until your component operates as follows:
• TV: power-off
• Other components: power-on
• TV without a power switch: the Channel + function works.
Step 1: Entering the Code Number
1 See the supplied “Component code numbers” table, and find the
three-digit code number for the desired component.
If more than one code number is listed, use the number that is
listed first to complete the steps below.
For example, if you are setting up a Philips TV, you would use the
code number 086.
If your component is not listed, see “Searching for the Correct Code.”
2 While pressing the S (SET) button,
3 Press the button of the component
that you want to set up.
TV
VCR
CBL
DVD
Note
On the VCR, CBL and DVD buttons, “VCR,” “Cable box,” and
“DVD player” are assigned respectively at the factory. But you
can also assign other components on these buttons. For details, see
“Changing the Component Type on the VCR, CBL and DVD
buttons.”
4 Enter the component’s code number.
For example, if you are entering the
code for a Philips TV, you would
press -86.
0
8
6
Your Code Number
5 Press and release the t button to store
the code number in the Commander’s
memory.
6 Go to “Step 2: Checking if the Code Number Works” to finish
setting up.
If you press a wrong button in step 4
to check if that button works.
For example, press the 1 button to see if it works on your component.
3 Check that the other buttons of the Commander are operating the
You can program the Channel Macro function on any of the buttons
listed below (macro keys).
For example, instead of pressing 1, 2, and then ENT button to
change the TV channel, you can perform these operations by
pressing only the N button.
The macro keys are:
N, m, M, x, X, and zREC.
(During “TV“ or “Cable box“ operations only.)
code number in the Commander’s memory.
6 Check that the Commander is operating the other functions of
your component by pressing the corresponding buttons on the
Commander. If they seem to be working properly, you are done
setting up the Commander.
If the component does not operate properly, repeat steps 1 to 5 and
search for another code.
Note
Be sure to proceed to each next step in the above procedure within
10 seconds; otherwise setting mode will be canceled.
Changing the Component Type on the
VCR, CBL and DVD buttons
At the factory, “VCR” is assigned to the VCR button, “Cable box” is
assigned to the CBL button and “DVD player” to the DVD button. By
completing the following procedure, you can change this setting so
that you can assign any component to these buttons.
2 While pressing the desired macro key, press the buttons required
for the operations in sequence.
For example, to program 1 t 2 t ENT on the N button, hold
down N first, press 1, 2, and ENT in sequence, and then release
N.
• Even if you try to program more than four operations and press the
corresponding buttons in step 2 above, only the first four buttons
that were pressed will be programmed.
• If you try to program only one operation on a macro key, the
setting operation will be rejected.
• You can program the Channel Macro function for up to three
components only. To program a fourth component, first clear all
macro keys for a component.
• If you have programmed the Channel Macro function for TV or
Cable box operation, the button used as a macro key cannot be
used for Fastext buttons.
To change or clear a program
Press the VCR, CBL or DVD button.
When you want to change the setting, or if you are no longer using a
programmed operation, follow the procedure below to overwrite or
clear the program.
Press and release the x (stop) button.
1 Hold down the macro key that you want to change or clear.
Press and release one of the following buttons:
1 to assign a VCR
3 to assign a Cable box
8 to assign a TV
- to assign a DVD
2 After waiting for about three seconds, press the new sequence of
buttons, or, to clear the program, press and release -, and then
press and release ENT.
While pressing the S (SET) button, press the 1 button.
3 Release the macro key.
5 Press and release the t button.
6 Enter the component’s code number by following steps 2 to 6 of
“Entering the Code Number,” or steps 1to 6 of “Searching for the
Correct Code.”
Operating a Component
TV
VCR
CBL
VCR
CBL
DVD
1
2
3
4
5
6
7
1-
8
0
9
2ENT
PROGR
To program a series of operations
1 Press the desired component select button.
(You can select “TV” or “Cable box” only.)
Note
Be sure to wait for about three seconds in step 2 above. While you
are holding down the macro key and waiting, the programmed
signals are transmitted; therefore, if you are aiming the Commander
at your component, the programmed operations may be performed
before you go on with the procedure.
DVD
component on the Commander.
If the Commander Does not Seem to be
Working...
2 Point the Commander directly at the component.
3 Press the button for the function you want to use.
• First, try repeating these setup procedures using the other codes
listed for your component (see the supplied “Component code
numbers” table).
See “Remote Button Descriptions” for complete descriptions of the
buttons on the Commander.
Troubleshooting
If you have problems setting up or using the Commander:
• When setting up the Commander, carefully go through the
procedures described in “Setting the Code.” If the code that is
listed first for your component does not work, try other codes for
that component in the order in which they are listed. If all the
codes fail to work (or if your component is not listed in this
manual), try using the procedures in “Searching for the Correct
Code.”
Operating a Cable box
2 To change the programme.
3 To select double-digit
numbers.
Work in the same way as
your Cable box’s
commander.
4 To change the input mode
(H/V).
8 To move the cursor upward,
downward, to the right or
left.
9 To call up the MENU display.
qd To select a number between
20 and 29.
qf PROGR+:
Programme up.
PROGR–:
Programme down.
qh To operate JUMP,
FLASHBACK or CHANNEL
RETURN function on the
Cable box, depending on the
manufacturer’s setting.
qj To bring up the Master
Guide.
qk To enter the selection.
ql Fastext buttons.
General
S
TV
MENU
GUIDE
OK
1 To set up the Commander,
press S (SET) while pressing
1.
5 2+: Volume up.
2–: Volume down.
7 To mute the volume on the
TV.
qa To turn on and off the power
of the selected component.
qs Component select buttons.
To switch to the operations of
each component, press the
button on which that
component is assigned.
REC
z The number 5 button and
the PROGR+ button each
have a tactile dot for ease of
use.
Notes
If you still cannot get the Commander to work properly, see
“Troubleshooting.”
1 Press the button of the desired
Remote Button Descriptions
The Channel Macro function may not work correctly for some
components.
corresponding functions of the component.
You can write down the code number on the label inside the
battery compartment lid.
• Check that you are aiming the Commander directly at the
component, and that there are no obstructions between the
Commander and the component.
• Make sure the batteries you are using are not worn out, and that
they are inserted correctly.
• Check that the button of the TV, VCR, CBL, or DVD is pressed to
choose your desired component.
• Check that the component has infrared remote capability. For
example, if your component did not come with a remote
commander, it is probably not capable of being controlled by a
remote commander.
• Should any problem persist, reset the Commander to the factory
setting by pressing the 1, t and 2– buttons simultaneously.
Note
5 When the correct code is found, press the t button to store the
1
2
3
4
Setting a channel with a single
button (Channel macro function)
The series of operations that can be programmed must consist of two
to four sequential pressings of the - to 9 buttons or ENT button.
Be patient as you do this; it could take as many as 120 tries before
the correct code number is located.
S
press the 1 button.
1 Turn on the component you want to set up.
2 Aim the Remote Commander at the component and press a button
Notes
3 Press and release the PROGR+ button. Then press and release the
Each time you press the PROGR+ button and then the 1 button, a
new code number will be transmitted.
Step 2: Checking if the Code Number Works
Under normal conditions, batteries will last up to 6 months. If the
Commander does not operate properly, the batteries might be worn
out. Replace the batteries with new ones.
want to set up.
Setting the Code
Press the 1 button while pressing the S (SET) button and then go
back to step 2.
When to replace the batteries
1 While pressing the S (SET) button, press the 1 button.
2 On the Commander, press the button of the component that you
Basically, use this Commander in the same way as the Commanders
supplied with your components.
• Using this Commander will not increase the functions of your
components. The functions of the Commander are limited to the
functions of the components themselves. For example, if your TV
does not have a MUTING function, the % button on this
Commander will not function with your TV.
• Some functions of the component may not work with this
Commander.
Operating a DVD
2 Number buttons: To set items
selected from the screen.
3 To select numbers 10 and
above.
4 To change the sound.
6 To show the current play
status on the screen.
8 To move the cursor upward,
downward, to the left, or to
the right.
9 To display the DVD menu.
0 To record, press N while
pressing zREC.
First release N, then release
zREC.
qd To enter the setting. To set
items selected from the
screen.
Operating a TV
2 To change the programme.
Also to turn on the power.
3 To select double-digit
numbers.
Works in the same way as
your TV’s commander.
4 To change the input mode.
6 To switch to Teletext.
8 To move the cursor upward,
downward, to the right or
left.
9 To call up the MENU display.
qd To select a number between
20 and 29.
qf PROGR+:
Programme up.
PROGR–:
Programme down.
qg To turn on.
To return from Teletext to
TV.
qh To operate JUMP,
FLASHBACK, or CHANNEL
on the TV, depending on the
manufacturer’s setting.
qk To enter the selection.
ql Fastext buttons.
qf PROGR+:
To proceed to the
next location or
song.
Programme up.
PROGR–:
To proceed to the
previous location or
song.
Programme down.
qg To switch the subtitle.
qh To display the title menu.
qj To clear the selected
characters from the screen.
To select the deck.
qk To execute items selected
from the screen.
ql N:
To play.
x:
To stop.
m: To rewind.
M: To fast-forward.
w; X:
To pause.
Specifications
Operable distance
Power requirements
Battery life
Dimensions
Mass
Approx. 7 m (23 ft) (varies depending of the
component of each manufacturer)
Two size AA (R6) batteries (not supplied)
Approx. 6 months (varies depending on
frequency of use)
Approx. 55 × 200 × 32 mm (w/h/d)
(2 1/4 × 7 7/8 × 1 5/16 in)
Approx. 95 g (3.4 oz) (not including
batteries)
Design and specifications are subject to change without notice.
Operating a VCR
2 To change the programme.
3 To select double-digit
numbers.
Works in the same way as
your VCR’s commander.
4 To switch the signals
supplied to the TV.
6 To expose the on-screen
display.
8 To move the cursor upward,
downward, to the left, or to
the right.
9 To call up the MENU display.
0, ql and w;
N:
To play.
x:
To stop.
m:
To rewind.
M:
To fast-forward.
zREC: To record, press N
while pressing
zREC.
X:
To pause.
qd To select a number between
20 and 29.
qf PROGR+:
Programme up.
PROGR–:
Programme down.
qg To change the input mode.
qk To enter the selection.
The validity of the CE marking is restricted to only those countries
where it is legally enforced, mainly in the countries EEA (European
Economic Area).
中文
每按一次 PROGR+ 按鈕,然後按 1 按鈕時,新的代碼將被傳送。
對於您要使用遙控器控制的每一個組成機,請按照下列步驟 1 和 2
進行操作。
設定遙控器
步驟 1:輸入代碼
關於預調遙控器
本遙控器工廠預調為操作 Sony 廠牌的組成機。
如果您正在使用此遙控器控制 Sony 廠牌的組成機,則在使用之前您
不必預調遙控器。
若要設定遙控器用於其他(非 Sony)製造商的組成機,或用於未作工
廠預調的組成機,則您需要按照說明書中的指示用正確的組成機專用
代碼預調遙控器。(您也可以參看附帶的“組成機代碼號數”表。)
能預調的組成機
按鈕
工廠設定
TV
VCR/電纜箱/DVD/TV
TV
VCR
CBL
DVD
Sony TV
Sony VHS VCR (VTR3)
—
Sony DVD 播放機
註
• 遙控器可以設定為每個按鈕只操作一個組成機-除非它們的代碼碰
巧相同。例如,您不能將遙控器設定為同時操作 Sony TV 和
Panasonic TV(因為它們使用不同的代碼)。
• 您甚至可能無法操作有工廠預調的 Sony 廠牌的組成機。若是這
樣,請按照“設定代碼”中的步驟進行操作。
1 參看附帶的“組成機代碼號數”表,並找出您要使用的組成機的三
位數代碼。
如果不止一個代碼被列出,則用列出的第一個代碼以完成下列步
驟。
例如,如果您正在設定 Philips TV,則使用代碼 086。
如果您的組成機未被列出,則參看“尋找正確代碼”。
2 同時按 S(SET)按鈕和 1 按鈕。
3 按您想要設定的組成機的按鈕。
S
TV
VCR
CBL
DVD
註
在 VCR,CBL 和 DVD 按鈕上,工廠設定時分別指定為“錄像
機”,“電纜箱”和“DVD 播放機”。但是,您也可以在這些按鈕
上指定其他的組成機。有關詳細說明,請參看“改變 VCR,CBL 和
DVD 按鈕上的組成機類型”。
4 輸入組成機的代碼。
例如,如果您正在輸入 Philips TV 的
代碼,則按 -86。
0
8
6
您的代碼
5 按住並釋放 t 按鈕,將代碼儲存在遙控器記憶
裝電池
體中。
更換電池之前,請預先準備新電池。
滑動並打開電池室,然後裝入兩個尺寸 AA(R6)電池(不附帶)。
確保電池上的 + 和 - 與電池室中的 + 和 - 相符。
1
4 重複步驟 3 直至找到正確的代碼。
設定代碼
2
6 進入“步驟 2:檢查代碼是否起作用”以完成設定。
如果您在步驟 4 中按錯按鈕
同時按 S(SET)按鈕和 1 按鈕,然後回到步驟 2。
繼續操作直至您的組成機呈現如下操作狀態:
• 電視機:電源關
• 其他組成機:電源開
• 不帶電源開關的電視機:Channel + 功能起作用。
您可以在以下列出的任何按鈕上編輯頻道指令功能(指令鍵)。
例如,您可以只按 N 按鈕,便可改變電視機頻道,而不用先按
1,2,再按 ENT 按鈕。
進行此代碼尋找要有耐心;最多可能要試 120 次才會找到正確的
代碼。
5 當找到正確的代碼時,按 t 按鈕將代碼儲存在遙控器記憶體中。
6 通過按遙控器上相應的按鈕檢查遙控器是否能執行您的組成機的其
他功能。如果這些按鈕正確工作,則您完成了遙控器的設定。
如果您仍然不能讓遙控器正確工作,則參看“故障探尋”。
頻道指令功能可能不能正確地對某些組成機起作用。
註
若要編輯操作系列
在以上操作中,確保在 10 秒鐘之內進行下一步操作;否則,設定模
式將被取消。
1 按想要的組成機選擇用按鈕。
(您只能選擇“電視機”或“電纜箱”。)
改變 VCR,CBL 和 DVD 按鈕上的組成機類型
2 按想要的指令鍵的同時依次按操作需要的按鈕。
例如,若要在 N 按鈕上編輯 1 t 2 t ENT,請首先按住
N,然後依次按 1,2 和 ENT,最後釋放 N 。
工廠設定時,“錄像機”被指定至 VCR 按鈕,“電纜箱”被指定至
CBL 按鈕,“DVD 播放機”被指定至 DVD 按鈕。完成下列步驟,您可
以改變此設定以便您能將任何組成機指定為這些按鈕。
1 同時按 S(SET)按鈕和 1 按鈕。
2 按 VCR,CBL 或 DVD 按鈕。
3 按住並釋放 x(停止)按鈕。
4 按住並釋放下列按鈕之一:
1
3
8
-
1 打開您想要設定的組成機。
的步驟 1 至步驟 6 輸入組成機的代碼。
在正常條件下,電池耐用 6 個月。如果遙控器操作不靈,則電池可能
已耗盡。更換新電池。
註
• 兩個電池都一起換新。
• 切勿花 3 分鐘以上時間更換電池;否則,您的代碼設定將被抹去。
電池須知
• 切勿混用新舊電池或不同類型的電池。
• 如果電池內的電解液漏液,則用布擦拭電池室內污染的地方並更換
新電池。為防止電解液漏液,當您將長期不使用遙控器時,請取下
電池。
您可以把代碼寫在電池室蓋內的標籤上。
如果遙控器不起作用...
• 首先,請用列出的您的組成機專用的其他代碼反覆試試這些設定步
驟(參看“組成機代碼號數”表)。
• 如果試過列出的您組成機的全部代碼之後,您仍然不能使遙控器正
確工作,則試試“尋找正確代碼”中說明的尋找方法。
尋找正確代碼
如果試過列出的您組成機的全部代碼之後,您仍然不能使遙控器起作
用(或如果您的組成機沒列在“組成機代碼號數”表中),則試試下
述方法。
開始尋找功能之前
將每個組成機設定至下列狀態才能執行尋找功能。
電視機:電源開
其他組成機:電源關
1 同時按 S(SET)按鈕和 1 按鈕。
2 在遙控器上,按您想要設定的組成機的按鈕。
3 按住並釋放 PROGR+ 按鈕。然後按住並釋放 1 按鈕。
1 按遙控器上您要控制的組成機的按
• 即使您試著編輯的操作多於四個並在上述步驟 2 中按相應的按鈕,
您也只能編輯所按的前四個按鈕。
• 如果您試著在一個指令鍵上僅編輯一個操作,則設定操作被拒絕。
• 您最多只能為三個組成機編輯頻道指令。若要編輯第四個組成機,
則先清除其中一個組成機的所有指令鍵。
• 如果您已經為電視機或電纜箱操作編輯了頻道指令功能,則用作指
令鍵的按鈕不能用於 Fastext 按鈕。
TV
VCR
CBL
DVD
鈕。
3 按您要使用的功能的按鈕。
使用遙控器的注意事項
一般來說,遙控器的使用方法與您的組成機附帶的遙控器的使用方法
相同。
• 使用本遙控器不會增加您的組成機的功能。遙控器的功能限於組成
機本身的功能。例如,如果您的電視機沒有 MUTING 功能,則本遙
控器上的 % 按鈕不對您的電視機起作用。
• 組成機的某些功能可能無法用本遙控器控制。
4 用於改變輸入模式(H/V)。
1
2
3
1 同時按 S(SET)和 1,用於
設定遙控器。
4
5
6
5 2+: 音量昇。
7
8
9
2–: 音量降。
VCR
1-
CBL
0
DVD
2ENT
PROGR
MENU
GUIDE
7 用於靜調電視機的音量。
qj 用於調出 Master Guide。
qd 用於在 20 和 29 之間選擇數
字。
qk 用於輸入選擇件。
qs 組成機選擇用按鈕。
用於切換到各組成機的操作,
按指定組成機的按鈕。
控制 DVD
z 數字 5 按鈕和 PROGR+ 按鈕
各有一個觸點便於使用。
3 用於選擇 10 和 10 以上的數
字。
控制電視機
2 用於改變頻道。
也可以用於打開電源。
3 用於選擇雙位數。
與您電視機的遙控器上的此按
鈕起相同的作用。
4 用於改變輸入模式。
3 釋放指令鍵。
qd 用於在 20 和 29 之間選擇數
字。
9 用於調出 MENU 顯示。
2 數字按鈕:用於設定在屏幕上
選擇的項目。
ql Fastext 按鈕。
qf PROGR+:
用於進到下一個位置
或曲子。
頻道昇。
PROGR–:
用於進到上一個位置
或曲子。
頻道降。
qf PROGR+:
頻道昇。
PROGR–:
頻道降。
8 用於上下或左右移動游標。
qg 用於轉換副標題。
9 用於顯示 DVD 選單。
qh 用於顯示標題選單。
0 同時按 N 和 zREC,用於錄
影。
首先釋放 N ,然後釋放
zREC。
qj 用於清除在屏幕上選擇的字
符。
用於選擇機座。
qd 用於輸入設定。用於設定在屏
幕上選擇的項目。
qg 用於打開電源。
用於從 Teletext 返回到電視
機。
qk 用於實行在屏幕上選擇的項
目。
ql N: 用於播放。
x:
用於停止。
m: 用於重繞。
qh 根據製造商的設定,用於控制
電視機上的 JUMP,FLASHBACK
或 CHANNEL。
M: 用於快進繞。
w; X:
用於暫停。
qk 用於輸入選擇件。
ql Fastext 按鈕。
規格
控制錄像機
2 用於改變頻道。
如果您在進行設定或使用遙控器時有問題:
• 設定遙控器時,請按照“設定代碼”中的說明小心操作。如果列出
的第一個組成機代碼不起作用,則按照列出的順序逐一試用組成機
的其他代碼。如果所有代碼都不起作用(或者如果在本說明書中未
列出您的組成機),則試著操作“尋找正確代碼”中的步驟。
• 檢查您是否將遙控器對準組成機,並且在遙控器和組成機之間無任
何障礙物。
• 確保您正在使用的電池未耗盡,並且被正確插入。
• 檢查是否按了 TV,VCR,CBL 或 DVD 按鈕選擇您想要的組成機。
• 檢查組成機有無紅外線遙控能力。例如,如果您的組成機不附帶遙
控器,則很可能不能用遙控器控制。
• 如果問題仍存在,則同時按 1,t 和 2– 按鈕將遙控器重設為
工廠設定。
9 用於調出 MENU 顯示。
6 用於在屏幕上顯示當前播放狀
態。
8 用於上下或左右移動游標。
故障探尋
8 用於上下或左右移動游標。
4 用於改變聲音。
2 等待約三秒鐘後,以新的次序按按鈕,或,若要清除編輯內容,按
住並釋放 -,然後按住並釋放 ENT。
確保在上述步驟 2 中等待約三秒鐘。當您按住指令鍵並等待時,已編
輯的訊號被傳送;因此,如果您正將遙控器對著您的組成機,則在您
繼續操作之前已編輯的操作可能被執行。
qf PROGR+:
頻道昇。
PROGR–:
頻道降。
qh 根據製造商的設定,用於控制
電纜箱上的 JUMP,FLASHBACK
或 CHANNEL RETURN 功能。
qa 用於打開和關閉所選組成機的
電源。
OK
6 用於轉換到 Teletext。
2 將遙控器直接對準組成機。
參看“遙控按鈕說明”以瞭解遙控器上按鈕的完整說明。
共同
3 用於選擇雙位數。
與您電纜箱的遙控器上的此按
鈕起相同的作用。
S
TV
1 按住您要改變或清除的指令鍵。
註
控制組成機
2 用於改變頻道。
註
若您想改變設定,或您不再使用一個編輯過的操作,則按照下列步驟
覆蓋或清除編輯內容。
6 按照“輸入代碼”中的步驟 2 至步驟 6,或“尋找正確代碼”中
控制電纜箱
遙控按鈕說明
REC
若要改變或清除編輯內容
指定錄像機
指定電纜箱
指定電視機
指定 DVD
例如,按 1 按鈕檢查此按鈕對您的組成機是否起作用。
何時須更換電池
可以編輯的操作系列必須由 - 至 9 按鈕或 ENT 按鈕的兩次至四
次的連續按壓組成。
註
5 按住並釋放 t 按鈕。
3 檢查遙控器的其他按鈕是否能執行相應的組成機的功能。
指令鍵:
N,m,M,x,X,和 zREC
(僅在“電視機”或“電纜箱”操作過程中。)
如果組成機操作不正常,則重複步驟 1 至 5 並尋找其他代碼。
步驟 2:檢查代碼是否起作用
2 將遙控器對準組成機並按一個按鈕,檢查那個按鈕是否起作用。
用單一按鈕設定頻道(頻道指令功能)
3 用於選擇雙位數。
與您錄像機的遙控器上的此按
鈕起相同的作用。
4 用於轉換提供給電視機的訊
號。
6 用於陳述屏幕顯示。
8 用於上下或左右移動游標。
9 用於調出 MENU 顯示。
0,ql 和 w;
N:
用於播放。
x:
用於停止。
m: 用於重繞。
M: 用於快進繞。
zREC: 同時按 N 和
zREC,用於錄影。
X:
用於暫停。
qd 用於在 20 和 29 之間選擇數
字。
qf PROGR+:
頻道昇。
PROGR–:
頻道降。
qg 用於改變輸入模式。
qk 用於輸入選擇件。
可控制距離
電源要求
電池壽命
尺寸
質量
約 7 m(因各廠牌的組成機而異)
兩個尺寸 AA(R6)電池(不附帶)
約 6 個月(因使用的頻率而異)
約 55 × 200 × 32 mm(寬/高/深)
約 95 g(不含電池)
設計和規格如有變動,恕不另行通知。
CE 標誌的有效性僅限於法律強制的國家,主要為 EEA(歐洲經濟地
區)國家。
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement