Samsung | GN7A2IFXD | Samsung GN7A2IFXD GEO Built in, 5 Burner Gas Cooktop User Manual

GB
Installation and
User Manual
GN7A2IFXD
Gas cooktop
P/N : 50553-44070
GB
Contents
Preface........................................................4
Safety Warning...................................... 5-10
- Safety Warning.......................................... 5
- Installation................................................. 6
- Child and People Safety............................ 7
- During Use.................................................8
- Cleaning & Service.................................. 10
- Environmental Information...................... 10
Instructions for use and maintenance.....11-19
- Description of the appliance.................... 11
- How to Use the Appliance........................12
- Safety and Energy saving advice............ 14
- Cleaning and Maintenance......................16
- Troubleshooting....................................... 18
- Application for Service............................. 19
Technical instructions.......................... 20-27
- Technical instructions.............................. 20
- Engineers technical data......................... 21
- Positioning............................................... 22
- Installing the appliance............................ 23
- Gas Connection...................................... 24
- Electrical Connection.............................. 25
- Gas Conversion.......................................26
- Burner Features...................................... 27
3
Preface
Safety Warning
Thank you for choosing a Samsung gas cooktop.
To use this appliance correctly and prevent any potential risk, read these instructions before
using the appliance.
Keep these instructions in a place where you can find them easily.
If you are unsure of any of the information contained in these instructions, please contact the
Samsung customer care center.
These instructions are only valid for the countries of destination, the identification symbols
which are indicated on the cover of the instruction manual.
The manufacturer shall not be responsible for any damages to persons or property caused by
incorrect installation or use of the appliance.
The appliance has been certified for use in countries other than those marked on the
appliance.
The manufacturer also reserves the right to make any modifications to the products as may
be considered necessary or useful, also in the interests of the user, without jeopardising the
main functional and safety feafures of the products themselves.
The appliance is designed for a domestic environment and not a commercial one.
■ Your safety is of the utmost importance to Samsung.
■ You must read warnings carefully before installing or using the appliance.
■ This instruction booklet must be kept with the appliance for any future reference.
If the appliance is sold or transferred to another person, ensure the booklet is passed on to
the new user.
■ The manufacturer declines any liability should these safety measures not be observed.
■ The following marks are made to be easily understood so that you can prevent any
accident caused by misuse in advance, and use the appliance more conveniently.
■ Read the following contents thoroughly and ensure you understand them before reading
the instructions.
Danger/Warning
Neglect of this mark may result in severe personal injury or
death.
Caution
Neglect of this mark may result in minor personal injury or
property damage.
■ The following marks mean as follow:
General Danger, Warning and Caution
No Access
No Fire Tool
Must Do
Danger
■ If gas seems to leak, take the actions as follow :
- Do not turn on the light.
- Do not switch on/off any electrical appliance and do not touch any electric plug.
- Do not use a telephone.
1 Stop using the product and close the middle valve.
2 Open the window to ventilate.
3 Contact our service center by using a phone outside.
* The fuel gas contains mercaptan, so that you can smell the gas leak (smell of rotten garlic
or egg) even where only 1/1000 of the gas is in the air.
4
5
Installation
Child and People Safety
Warning
Warning
■ This appliance shall be installed in
accordance with regulations in force
and only used in a well ventilated
space.
■ Prior to installation, ensure that the
gas and electrical supply complies
with the type stated on the rating
plate.
■ Where this appliance is installed in
marine craft or in caravans, it shall not
be used as a space heater.
■ The gas pipe and electrical cable
must be installed in such a way that
they do not touch any parts or the
appliance.
■ Do not allow children to play near or with the appliance.
The appliance gets hot when it is in use.
Children should be kept away until it has cooled.
Caution
■ This appliance is designed to be operated by adults.
■ Children can also injure themselves by pulling pans or pots off the appliance.
Caution
■ This appliance should be installed by a qualified technician or installer.
■ The adjustment conditions for this appliance are stated on the label or data plate.
■ Remove all packaging before using the appliance.
■ After unpacking the appliance, make sure the product is not damaged and that the
connection cord is in perfect condition. Otherwise, contact the dealer before installing
the appliance.
■ The adjacent furniture and all materials used in the installation must be able to
withstand a minimum temperature of 85˚C above the ambient temperature of the
room it is located in, whilst in use.
■ In the event of burner flames being accidentally extinguished, turn off the burner
control and do not attempt to re-ignite the burner for at least one minute.
■T
he use of a gas cooking appliance results in the production of heat and moisture in the
room in which it is installed. Ensure that the kitchen is well ventilated: keep natural
ventilation holes open or install a mechanical ventilation device (mechanical extractor hood).
■ Prolonged intensive use of the appliance may call for additional ventilation, for
example opening of a window, or more effective ventilation, for example increasing
the level of mechanical ventilation where present.
6
■ This appliance is not intended for use by children or other persons whose physical,
sensory or mental capabilities or lack of experience and knowledge prevents them
from using the appliance safety without supervision or instruction by a responsible
person to ensure that they can use the appliance safety.
7
During Use
During Use (Continued)
Warning
■ Only use the appliance for preparing
food.
■ Do not use or store flammable
materials in the appliance storage
drawer or near this appliance.
■ Perishable food, plastic items and
aerosols may be affected by heat and
should not stored above or below the
appliance.
■ Do not spray aerosols in the vicinity of
this appliance while it is in operaiton.
■ Ensure the control knobs are in the
‘OFF’ position when not in use.
■ Do not modify this appliance.
■T
he use of a gas cooking appliance results
in the production of heat and moisture in
the room in which it is installed. Ensure
that the kitchen is well ventilated : keep
natural ventilation holes open or install a
mechanical ventilation device
(mechanical
extractor hood).
■ Do not use this appliance if it is in
contact with water. Do not operate
this appliance with wet hands.
Caution
■ The heating and cooking surfaces of
the appliance become hot when they
are in use, take all due precautions.
■ Do not use large cloths, tea towels or
similar as the ends could touch the
flames and catch fire.
■ Never leave the appliance unattended
when cooking with oil and fats. If fat
and oil overheats, it can ignite
extremely quickly.
■ Unstable or misshapen pans should
not be used on the appliance as they
can cause an accident by tipping or
spillage.
8
■ This appliance is intended for domestic cooking only. It is not designed for commercial or
industrial purposes.
■ Prolonged intensive use of the appliance may call for additional ventilation, for example
opening of a window, or increasing the level of mechanical ventilation where present.
■ Use heat-resistant pot holders or gloves when handling hot pots and pans.
■ Do not let pot holders come near open flames when lifting cookware.
■ Take care not to let pot holders or gloves get damp or wet, as this causes heat to transfer
through the material quicker with the risk of burning yourself.
■ Only ever use the burners after placing pots and pans on them. Do not heat up any empty
pots or pans.
■ Never use plastic or aluminium foil dishes on the appliance.
■ When using other electrical appliances, ensure the cable does not come into contact with
the appliance surfaces of the cooking appliance.
■ If you have any mechanical parts eg. an artifical heart in your body, consult a doctor before
using the appliance.
■ Do not use a towel or other bulky cloth in place of a pot holder. Such cloths can catch fire
on a hot burner.
■ When using glass cookware, make sure it is designed for top plate cooking.
■ To minimise the possibility of burns, ignition of flammable materials and spillage, turn
cookware handles toward the side or center of the top plate without extending over
adjacent burners.
■ Always turn burner controls off before removing cookware.
■ Carefully watch foods being fried at a high flame setting.
■ Always heat fat slowly and watch as it heats.
■ Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh
foods can cause hot fat to bubble up and over the sides of the pan.
■ Never try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool.
9
Cleaning & Service
Description of the appliance
Warning
2
■ Never use abrasive or caustic
cleaning agents.
■ B
efore attempting to clean the appliance, it should be disconnected from the mains
and cooled.
■ You should not use a steam jet or any other high pressure cleaning equipment to
clean the appliance.
Environmental Information
■ After installation, please dispose of the packaging
with due regard to safety and the environment.
■ When disposing of an old appliance, make it
unusable, by cutting off the cable.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
■ This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
■ Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take this item
for environmentally safe recycling.
■ Business users should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
10
3
12
13
■ This appliance should only be
repaired or serviced by an authorised
Service Engineer and only genuine
approved spare parts should
be used.
Caution
11
14
1
6
7
8
9
5
10
4
7. Control knob for center
rear burner
(Semi-rapid burner)
8. Control knob for center
front burner
(Semi-rapid burner)
9. Control knob for right rear
burner (Rapid burner)
1. Top plate
2. Triple crown burner
3. Semi-rapid burner
4. Auxiliary burner
5. Rapid burner
6. C
ontrol knob for left burner
(Triple crown burner)
Burner
Triple crown
10. Control knob for right
front burner
(Auxiliary burner)
11. Pan support left (Cast iron)
12. Pan support center (Cast iron)
13. Pan support right (Cast iron)
14. W
ok pan support
(Only use for triple crown burner)
Auxiliary, Semi-rapid and Rapid
16-1
16. Burner lid
16-1. Inner Burner lid
16-2. Outer Burner lid
17. Flame Spreader
18. Burner Cup
19. Ignition Electrode
20. Flame supervision device
16
16-2
17
18
19
20
Wok pan support
21
Knob
21. Wok pan support
22. Pan support (left)
(Cast iron)
23
24
25
22
11
23. Control knob
24. Sealing ring
25. Valve
How to Use the Appliance
Turn off
Turn on
1
Preparation
The following symbols will appear on the control panel, next to each control handle :
Circle : gas off
Small flame : minimum setting
Large flame : maximum setting
Ignition position
■ The minimum setting is at the end of the anti-clockwise rotation of the control handle.
■ All operation positions must be selected between the maximum and minimum position.
■ The symbol on the control panel, next to the control handle will indicate which burner it operates.
2
How to Use the Appliance (Continued)
3
Extinguishment
■ Turn the control handle to clockwise, to setting ‘O’ (off position)
Ignition & Adjustment
■ Right after extinguishment, the appliance is still hot. Be careful not to
burn yourself.
■ Place a pot or a pan on the corresponding cooking position.
■ Fully press down the control handle for the corresponding cooking position and turn it to the
left, to the ignition position, and hold it there for a few seconds at most until the burner ignites.
■ After igniting, keep the control handle pressed for about 5~8seconds more because the heat
sensor that opens the gas channel has to warm up first. Set control handle to the position you
want.
■ If the burner does not light, repeat the process.
■ The flame size can be set continuously between maximum and minimum by slowing turning the
control handle.
■ This appliance is fitted with a flame supervision device which cuts off
the supply of gas to a burner if the flame goes out, for example if food
has boiled over, or if there is a sudden draught.
■ In the event of the burner flames being accidentally extinguished, turn
off the burner control and do not attemp to re-ignite the burner for at
least one minute.
■ If the igniters are dirty, this makes the burner harder to light, so you
should keep them as clean as possible. Do this with a small brush and
make sure that the ignition device is not hit or knocked violently.
■ The flame supervision device shall not be operated for more than 15
seconds. If after 15 seconds the burner has not lit, stop operating the
device and open the compartment door and/or wait at least one minute
before attempting to reignite the burner.
12
13
Safety and Energy saving advice
Safety and Energy saving advice (Continued)
- The diameter of the bottom of the pan should correspond to that of the burner.
BURNERS
Triple-Crown
Rapid
Semi-Rapid
Auxiliary
Φ min.
200mm
200mm
130mm
100mm
PANS
■ Do not use cookware on the
appliance that overlaps the
edge.
Φ max.
260mm
240mm
180mm
120mm
NO
YES
Do not use small diameter cookware on
large burners.
The flame should never come up the
sides of the cookware.
Avoid cooking without a lid or with the
lid half off
- as this wastes energy
Always use cookware that are
suitable for each burner, as to
avoid wasting gas and
discolouring the cookware.
Always place the lid on the
cookware.
Do not use a pan with a convex or
concave bottom.
Only use pots, saucepans and
frying pans with a thick, flat
bottom.
Do not place cookware on one side of a
burner, as it could tip over.
Do not use cookware with a large diameter
on the burners near the controls, which
when placed on the middle of the burner
may touch the controls or be so close to
them that they increase the temperature in
this area and may cause damage.
Never place cookware directly on top of
the burner.
Always place the cookware
right over the burners, not to
one side.
Do not place anything, eg. flame tamer,
asbestos mat, between pan and pan
support as serious damage to the
appliance may result.
Do not use excessive weight and do not
hit the hob with heavy objects.
This “WOK PAN SUPPORT” allows you to use
receptacles with a concave base.
■ “WOK PAN SUPPORT” is only for triple crown burner.
■ The manufacture declines all responsibility
CONCAVE PAN
if this additional wok pan support is not
Φ min.
Φ max.
used or are used incorrectly.
180mm
220mm
Place the cookware on top of
the trivet.
Handle cookware carefully
when they are on the burner.
■ It is not permitted to use roasting pans, frying pans or grill stones heated
simultaneously by several burners because the resulting heat build-up
may damage the appliance.
■ Do not touch the top plate and trivet while using or for a certain period
after using.
■ As soon as a liquid starts boiling, turn down the flame so that it will
barely keep the liquid simmering.
14
15
Cleaning and Maintenance
Cleaning and Maintenance (Continued)
■ Cleaning operations must only be carried out when the appliance is cool.
■ The appliance should be disconnected from your mains supply before
commencing any cleaning process.
■ Clean the appliance regularly, preferably after each use.
■ Abrasive cleaners or sharp objects will damage the appliance surface;
you should clean it using water and a little washing up liquid.
Soft Clothing
Sponge Brush
Soft Clothing
Usable
Nylon Brush
Soft cloth
Edible Oil
Nylon Brush
Soft Clothing
Soft Clothing
Soft Clothing
Acidic/Alkali
Metal Brush
Detergent
Sponge Brush
Sponge Brush
Neutral DetergentSponge Brush
Sponge Brush
neutral Detergent
Abrasive
Edible
Oil
Unusable
Metal Brush
Soft Clothing
Nylon Brush
Nylon Brush
Soft Clothing
Soft Clothing
Nylon Brush
Sponge Brush
Edible Oil
Sponge Brush
Edible Oil
Sponge Brush
Edible Oil
Thinner/Benzene
Acidic/Alkali
Detergent
neutral Detergent
neutral Detergent
neutral Detergent
neutral Detergent
Abrasive
Abrasive
neutral Detergent
neutral Detergent
Abrasive
Nylon Brush
Metal
Brush
Nylon
Brush
Metal Brush
Nylon Brush
Metal
NylonBrush
Brush
Edible Oil
Metal Brush
Metal Brush
Metal Brush
Edible Oil
Acidic/Alkali
Detergent
Acidic/Alkali
Edible
Oil
Detergent
Acidic/Alkali
Edible Oil
Detergent
Acidic/Alkali
Acidic/Alkali
Detergent
Detergent
Abrasive
Thinner/Benzene
Thinner/Benzene
Abrasive
Thinner/Benzene
Abrasive
Thinner/Benzene
Thinner/Benzene
Abrasive
Acidic/Alkali
Detergent
Metal Brush
Acidic/Alkali
Detergent
Abrasive
■ Remove the burner lids and Flame Spreaders by pulling them upwards and away
from the top plate.
■ Soak them in hot water and a little detergent.
■ After cleaning and washing them, wipe and dry them carefully. Make sure that the
flame holes are clean and completely dry.
■ Wipe the fixed parts of the burner cup with a damp cloth and dry afterwards.
■ Gently wipe the Ignition device and flame supervision device with a well wrung-out
cloth and wipe dry with a clean cloth.
■ Before placing the burners back on the top plate, make sure that the injector is not
blocked.
Thinner/Benzene
Thinner/Benzene
Pan support, Control handles
neutral Detergent
BURNERS
■ Re-assemble the Auxiliary, Semi-Rapid, Rapid and
Triple-Crown burners as follows :
Thinner/Benzene
■ Take off the Pan support.
■ Clean these and the control handles with a damp cloth, washing up liquid and warm
water. For stubbon soiling, soak beforehand.
■ Dry everything with a clean soft cloth.
Top plate
■ Regularly wipe over the top plate using a soft cloth well wrung out in warm water to
which a little washing up liquid has been added.
■ Dry the top plate thoroughly after cleaning.
■ Thoroughly remove salty foods or liquids from the hob as soon as possible to avoid
the risk of corrosion.
■ Stainless steel parts of the appliance may become discoloured over time. This is
normal because of the high temperatures. Each time the appliance is used these
parts should be cleaned with a product that is suitable for stainless steel.
16
16-1
16
16-2
17
18
1. Place the flame spreader (17) on to the burner cup (18) so that the ignition device and the flame
supervision device extend through their respective holes in the flame spreader.
The flame spreader must click into place correctly.
2. Position the burner lid (16,16-1,16-2) onto the flame speader (17) so that the retaining pins fit
into their respective recesses.
Replace parts in the correct order after cleaning.
- Do not mix up the top and bottom.
- The locating pins must fit exactly into the notches.
17
Troubleshooting
Application for Service
■ Repairs to the gas and electrical components of this appliance must only be carried out by
a suitably qualified and competent person to ensure safety.
■ However, some minor problems can be resolved as follows :
Problem
Not ignited
Probable cause
No Spark.
If you have any comments or questions regarding a Samsung products,
contact the SAMSUNG customer care center.
Region
Solution
Check the electricity supply
Country
Customer Care
Center (TEL)
BELGIUM
02 201 2418
CZECH
REPUBLIC
800 726 786
Assemble the lid correctly.
DENMARK
70 70 19 70
The gas supply is closed.
Open the gas supply completely.
FINLAND
030-6227 515
The gas supply is not completely
open.
Open the gas supply completely.
FRANCE
The burner lid is badly assembled.
Assemble the lid correctly.
The ignition plug is contaminated
with alien substance.
Wipe such alien substance with
dried clothing.
The burners are wet.
Dry the burners lids carefully.
The holes in the flame spreader are
clogged.
Clean the flame spreader.
Noise made when
combusted and ignited
The burner lid is badly assembled.
Assemble the burner lid
correctly.
Flame goes out when
in use.
The flame supervision device is
contaminated with alien substance.
Clean the flame supervision
device.
Product being cooked has boiled
over and extinguished the flame.
Turn off burner knob. Wait 60
seconds and reignite zone.
A strong draught may have blown
the flame out
Please turn off zone and check
cooking area for draught such as
open windows. Wait 60 seconds
and reignite zone
The holes in the flame spreader are
clogged.
Clean the flame spreader.
Different gas is used.
Check the gas used.
Unstable Flame
The burner lid is badly assembled.
Assemble the burner lid
correctly.
Gas Smell
A gas tap has been left on.
Check to see if any gas taps are
on.
There may be a leak between the
coupling and the gas bottle.
Make sure that the connection is
airtight.
The burner lid is badly assembled.
Badly ignited
Yellow Flame
■ If problem is not solved, please contact the Samsung customer care
center.
18
GERMANY
Web Site
www.
samsung.be
www.
samsung.com/cz
www.
samsung.com/dk
www.
samsung.com/fi
3260 SAMSUNG or
www.
08 25 08 65 65
samsung.com/fr
(€ 0,15/Min)
01805 - 121213
(€ 0,14/Min)
www.
samsung.de
06-80-SAMSUNG
www.
(7267864)
samsung.com/hu
800-SAMSUNG
www.
ITALIA
(7267864)
samsung.com/it
www.
LUXEMBURG 02 261 03 710
samsung.lu
0900
20
200
88
www.
Europe NETHERLANDS
(€ 0,10/Min)
samsung.nl
www.
NORWAY
815-56 480
samsung.com/no
www.
POLAND
0 801 801 881
samsung.com/pl
www.
PORTUGAL
80 8 200 128
samsung.com/pt
www.
SLOVAKIA 0800-SAMSUNG
(726786)
samsung.com/sk
HUNGARY
SPAIN
902 10 11 30
www.
samsung.com/es
FAX no.
N/A
Asia
Pacific
SAMSUNG ELECTRÓNICS IBÉRIA, S.A
Ciencies, 55-65 (Polígono Pedrosa)
08908 HOSPITALET DE LLOBREGAT (Barcelona)
Samsung Electronics Nordic AB
SE -19427 Kanalvägen 10A, Upplands Väsby, Sweden
Samsung Electronics U.K. Ltd. Customer Care Centre PO
Box 17243 Edinburgh, EH11 4YB United Kingdom
www.
0771-400 200
N/A
samsung.com/se
0330
SAMSUNG
www.
0870
U.K
(7267864)
samsung.com/uk
7221127
Republic of
www.
+44 (0)870
0818 717 100
Ireland
samsung.com/uk
7221127
http://www.
Switzerland 0800-SAMSUNG
N/A
(7267864)
samsung.com/ch/
www.
+7-495- 117105 Россия, Москва, Варшавское ш., д. 26
RUSSIA
8-800-555-5555
samsung.ru
783-0556
www.
+7 (3272) 050051 4th floor, 172 Dostyk Ave. Almaty Republic of
KAZAHSTAN 8-800-080-1188
samsung.kz
58-59-66 Kazakhstan
www.
+998-71- 100-742 12fl.,International Business Center,107B,Amir
UZBEKISTAN 8-800-120-0400
samsung.uz
120-7208 Temur str., Tashkent,Uzbekistan
www.
+380 (44) 30A, Spaska St, Floor 3, Kiev 04070, Ukraine
UKRAINE
8-800-502-0000 samsung.com/ur
537 59 48
www.
+370 52 Zemaites 21, Vilnius, LT-2009, Lithuania
LITHUANIA
8-800-77777
samsung.lt
139 770
http://www.samsung.
+371 7
J. Alunana 2, Riga, LV-1340, Latvia
LATVIA
800-7267
com/lv/index.htm
50 84 80
www.
ESTONIA
800-7267
samsung.ee
www.
(612)
Samsung Electronics Australia
AUSTRALIA
1300 362 603
samsung.com/au 9763 5750 7 Parkview Drive, Homebush Bay NSW 2127
Samsung
Malaysia Electronics Sdn. Bhd.
www.
03MALAYSIA
1800-88-9999 samsung.com/my
Level 1, Block 3B, Plaza Sentral, Jalan Stesen
22636759 3B-1-1.
Sentral 5, KL Sentral , 50470, Kuala Lumpur, Malaysia
SWEDEN
CIS
Address
Samsung Electronics Benelux B.V.
N/A
Medialaan 50, 1800 Vilvoorde, Belgium
Distributor
pro Českou republiku Samsung Zrt., česka
N/A
organizační složka, Sokolovská 394/17, Praha 8, 180 00
Samsung
Electronics
Nordic AB
N/A
SE -19427 Kanalvägen 10A, Upplands Väsby, Sweden
Samsung Electronics Nordic AB
N/A
SE -19427 Kanalvägen 10A, Upplands Väsby, Sweden
Samsung Service Consommateurs
01 48
rue des Vanesses BP 50116 - Villepinte -95950
63 06 38 66
ROISSY cedex, France
Electronics GmbH
01805 - Samsung
House, Am Kronberger Hang 6, 65824
121214 Samsung
Schwalbach/Ts., Deutschland
Samsung Electronics Magyar Rt.
N/A
Szépvölgyi Business Park, 1037 Budapest, Szépvölgyi út 35-37
02
Samsung Electronics Italia S.p.A
92141801 Via C. Donat Cattin, 5, 20063, Cernusco Sul Naviglio (MI)
Samsung Electronics Benelux B.V.
N/A
Medialaan 50, 1800 VilvoordeBelgium
Samsung
Electronics Benelux B.V.
N/A
Postbus 681 2600AR Delft Nederland
Samsung Electronics Nordic AB
N/A
SE -19427 Kanalvägen 10A, Upplands Väsby, Sweden
+48-22- Samsung Electronics Polska sp. Z o.o.
607 4448 Dział Obsługi Klienta02-678 Warszawa; ul. Szturmowa 2a
SAMSUNG ELECTRÓNICA PORTUGUESA, S.A
N/A
Rua Cesario Verde, no 5-4, Piso2795-753 Queijas-Portugal
Vajnorská 100/B, Bratislava, 831 04
N/A
THAILAND
1800-29-323202www.
689-3232
samsung.com/th
Thai Samsung Electronics Co.,Ltd Service Department 1,6
floor Boonmitr Building 138 Silom Rd., Suriyawong
Bangrak Bangkok 10500
02689-3298 บริษัท ไทยซัมซุงอิเล็คโทรนิคส์ จำกัด
เลขที่ 138 อาคารบุญมิตร ชั้น 1,6 ถนนสีลม
แขวงสุริยวงศ์ เขตบางรัก กรุงเทพฯ 10500
19
Remark
Technical instructions
■ Do not modify this appliance.
Engineers technical data
Appliance Specification
■ This appliance must be installed by an authorised technician or
installer.
D
■ Prior to installation, ensure that the local distribution conditions
(nature of the gas and gas pressure) and the adjustment of the
appliance are compatible.
H
■ The adjustment conditions for this appliance are stated on the label
(or data plate).
■ This appliance is not connected to a combustion products evacuation
device. It shall be installed and connected in accordance with current
installation regulations. Particular attention shall be given to the
relevant requirements regarding ventilaton.
■ Before installing, turn off the gas and electricity supply to the
appliance.
■ All appliances containing any electrical components must be earthed.
■ Ensure that the gas pipe and electrical cable are installed in such a
way that they do not touch any parts of the appliacne which become
hot.
■ Gas pipe or connector shouldn’t be bent or blocked by any other
appliances.
■ Check the dimensions of the appliance as well as the dimensions of
the gap to be cut in the kitchen unit.
■ The panels located above the work surface, directly next to the
appliance, must be made of non-flammable material. Both the stratified surfacing and the glue used to secure it should be heat resistant,
to prevent deterioration.
■ Turn on appliance tap and light each burners.
Check for a clear blue flame without yellow tipping.
If burners shows any abnormalties check the following :
- Burner lid on correctly
- Flame spreader positioned correctly
- Burner vertically aligned with injector nipple
■ A full operational test and a test for possible leakages must be carried
out by the fitter after installaion.
■ The flexible hose shall be fitted in such a way that it cannot come into
contact with a moveable part of the housing unit and does not pass
through any space susceptible of becoming congested.
20
W
Model
GN7A2IFXD
Pan Support
Cast Iron
Wok pan Support
O (only use for Triple crown burner)
Top Plate
Stainless steel
Control Handle
Silver color
Weight
16kg
Dimension (WxDxH)
750*510*52
Ignition device
Continuous Ignition Type
Gas Connection
1/2 inch female thread
Electric supply
220~240V, 50/60Hz
Burner Feature
Triple-Crown (1EA), Rapid(1EA), Semi-rapid (2EA), Auxiliary (1EA)
○ APPLIANCE CLASS : Class 3
○ APPLIANCE CATEGORY :
BE/FR
GB/IT/PT/LT/ES/CZ/SK
PL
Cat.
II 2E+3+
II 2H3+
II 2E3B/P
P(mbar)
20/25 - 28-30/37
20 - 28-30/37
20-36
HU
NL
Cat.
II 2H3B/P
II 2L3B/P
P(mbar)
25-30
25 - 28-30
21
Positioning
Installing the appliance
1. Remove the pan supports, the burner lid and
flame spreader and carefully turn the
appliance upside down and place it on a
cushioned mat.
Take care that the Ignition devices and flame
supervision devices are not damaged in this
operation.
2. Apply the sealing strip provided around the
edge of the appliance.
3. Do not leave a gap in the sealing agent or
overlap the thickness.
■ Clearance around the gas appliance must comply with the requirement
of AS5601.
CLEARANCES REQUIRED
WHEN FITTING THE HOB
WITHOUT A COOKER HOOD ABOVE
CLEARANCES REQUIRED
WHEN FITTING THE HOB
WITH A COOKER HOOD ABOVE
600mm
700mm
700mm
400mm
55
15
Min0. mm
560m
m
0m
m
400mm
49
0m
m
49
560m
m
400mm
15
Min0. mm
Cut out size
Do not use a silicon sealant to seal the
appliance against the aperture.
Width : 560mm
Depth : 490mm
Thickness : 30~50mm
This will make it difficult to remove the
appliance from the aperture in future,
particularly if it needs to be serviced.
m
55
m
m
m
400mm
FO 0813
FO 0812
■ This appliance is to be built into a kitchen unit or 600mm worktop, providing the
following minimum distances are allowed ;
- The edge of the appliance must be a minimum distance of 55mm from a rear wall.
- A minimum distance of 150mm must be left between the side edges of the appliance and any
adjacent cabinets or walls.
- The minimum distance combustible material can be fitted above the appliance in line with the
edges of the appliance is 400mm. If it is fitted below 400mm a space of 50mm must be allowed
from the edges of the appliance.
- The minimum distance combustible material can be fitted directly above the appliance is 700mm.
(A) SEALING STRIP
(C) SCREW
(B) BRACKET
1. Place the bracket(B) over the holes that match the size
of the screws.There are one set of screw holes in each
corner of the hob(H).
Slightly tighten a screw(C) through the bracket(B) so
that the bracket is attached to the hob, but so that you
can still adjust the position it.
2. Carefully turn the hob back over and then gently lower it
into the aperture hole that you have cut out.
3. On the underneath of the hob, adjust the brackets into a
position that is suitable for your worktop.
Then fully tighten the screws(C) to secure the hob into
position.
40mm
H
a
H
H
H
150mm(MAX)
- This panel(a) must be positioned at a maximum distance of 150mm below the worktop.
H
22
H
H
H
23
Gas Connection
■ This appliance must be installed and connected in accordance with installation regulations in force in the country in which the appliance is to be used.
■ This appliance is supplied to run on natural gas only and cannot be used on
any other type of gas without modification. Conversion for use on LPG and
other gases must only be undertaken by a qualified person.
The gas inlet connection fitting is 1/2 inch female thread.
Gas distributed by pipe ; natural gas, propane-air gas or butane-air gas
For your safety, you must choose from the three following connection option.
Electrical Connection
■ This appliance must be earthed.
■ This appliance is designed to be connected to a 220~240V, 50/60Hz AC electricity supply.
■ The wires in the mains lead are coloured in accordance with the following code ;
- Green/yellow = Earth
- Blue
= Neutral
- Brown
= Live
■ The wire which is coloured green and yellow must be connected
to the terminal which is marked with the letter E or by the earth
symbol.
■ Connection with a rigid pipe made from copper and with
screw-on mechanical connectors.
Make the connection directly to the end of the elbow fitted on
the appliance.
■ Connection using flexible undulated metal tube with
screw-on connectors. (Fig. A)
You can use a flexible stainless steel pipe available from your
after sales service department.
Elbow
Fig.A
Fig.B
■C
onnection using flexible tube with screw-on connectors.
(Fig.B)
These tubes must not exceed 2 meters in length and must be
accessible along their entire length.
■ WIRING DIAGRAM
N
Elbow
Fig.A
Fig.B
■ For an existing installation, where it is not possible to fit a
Gasket
reinforced, braided, flexible gas hose, the connection can be
made with a flexible gas hose (maximum length 2meters),
Connector
with two clamps.
One on the connector, and the other on the pressure
Clamp
regulator, and a gasket should be fitted between the
connector and the hob’s elbow. (Fig.B)
N
CONNECTOR
N 1
GREEN & YELLOW TO EARTH
Gas supplied by tank or cylinder (butane/propane)
■ For the user’s safety, we advise the connection to be made
with a rigid pipe if this is possible, using a flexible undulated
metal tube with scerw-on connectors (maximum length
2meters) (Fig.A)
BLUE TO NEUTRAL
2
3
L 4
GND
L
5
6
①
②
GREEN TO EARTH
GND
BROWN TO LIVE
 MICRO SWITCHES
 IGNITER
(INPUT: 220V 50~60HZ, OUTPUT: 15.25V)
■Y
ou can obtain the connector and the gasket from your After-Sales Service.
In France, you must use a tube or a pipe featuring the “NF Gaz” logo.
If the installation is difficult, unscrew the Elbow slightly and tighten it after
locating the Elbow.
■ A full operational test and a test for possible leakages must be carried out
by the fitter after installation.
■ Access to the whole length of the connection hose must be possible and
the gas hose must be replaced before its use before the end of service life
(indicated on the hose)
24
Ignition
Electrode
25
L
Gas Conversion
1
2
Burner Features
■ Take precautions on the operations and adjustments to be carried out when
converting from one gas to another.
■ All work must be carried out by a qualified technician.
■ Before you begin, turn off the gas and electricity supply to the appliance.
Change the injector of the burners.
(Also same method on Triple crown burner)
Remove the pan support, Burner lid and Flame spreader.
Injector
Unscrew the injector using a 7 mm box spanner and replace it with
the stipulated injector for new gas supply. ( see table 1. Page 27.)
Carefully reassemble the all components.
After injectors are replaced, it is advisable to strongly tighten the
injector in place.
Adjusting of the taps of the cooking hob burners for
reduced consumption
➀ Turn the taps down to minimum.
Control handle
Tap
Sealing ring
Tap
by-pass screw
➁ Remove the control handles from taps.
➂ Adjusting the by-pass screw.
- For converting G20 into G30, the screw must be
screwed down fully tight.
- At this stage, light up the burners and turn the
control handles from max position to minimum
position to check flame stability.
- For converting G30 into G20, please change all
valve into new one.
➃ Replace the control handles on the taps.
■D
o not dismantle the tap shaft : in the event of a malfunction, change the whole tap.
■ Before placing the burners back on the top place, make sure that the injector is
not blocked.
■ A full operational test and a test for possible leakages must be carried out after
gas conversion. (such as soap water or gas detector)
■ After completing conversion, a qualified technician or installer has to mark “V”
on the right gas category
to match with the setting
0063
in rating plate.
GN7A2IFXD
S/N:
Remove the previous
G20/20mbar
220-240V 50/60Hz, Pmax 1W
setting “V” mark.
∑Qn G20: 11.3kW G30: 807g/h G31: 781g/h
G20-20mbar
26
G30/29mbar
G31/37mbar
GB Cat.: II2H3+
(Table 1)
Nominal heat input and flow rates see below at 15˚C at 1,013 mbar.
COUN- TYPE OF
TRY
GAS
BURNER
POSITION
Injector make
GB,IT
(1/100 mm)
FR,HU G-30
BE,LT
heat input
BUTANE Nominal
(Kw) (Hs)
NL,PT
ES,CZ 29 mbar Nominal flow rates
SK
(g/h)
Injector make
(1/100 mm)
G-30
heat input
PL BUTANE Nominal
(Kw) (Hs)
37 mbar Nominal flow rates
(g/h)
Injector make
GB,IT
(1/100 mm)
FR,BE G-31
heat input
LT,PT PROPANE Nominal
(Kw) (Hs)
ES,CZ 37 mbar
Nominal flow rates
SK
(g/h)
Injector make
GB,IT
(1/100 mm)
FR,BE G-20
heat rating
LT,PT NATURAL Nominal
(Kw) (Hs)
PL,ES 20 mbar
Nominal flow rates
CZ,SK
(L/h)
Injector make
(1/100 mm)
G-20
heat input
HU NATURAL Nominal
(Kw) (Hs)
25 mbar Nominal flow rates
(L/h)
Injector make
(1/100 mm)
G-25
heat input
NL NATURAL Nominal
(Kw) (Hs)
25 mbar Nominal flow rates
(L/h)
Triple-Crown
(3.8KW)
Max
Min
Rapid
Max
98
Min
Semi-rapid
Max
85
Min
Auxiliary
Max
65
Min
50
-
3.8
1.15
3.0
0.74
1.75
0.43
1.0
0.37
267
193
211
53
120
31
71
25
93
80
62
47
1.29
3.0
0.81
1.75
0.47
1.0
0.38
259
185
203
58
125
33
71
25
85
65
50
1.12
3.0
0.71
1.75
0.41
1.0
0.33
254
177
199
49
118
28
68
23
119
97
72
1.38
3.0
1.14
1.75
0.63
1.0
0.45
361
129
271
79
166
54
91
30
110
91
68
1.59
3.0
1.33
1.75
0.57
1.0
0.49
350
129
271
79
166
54
91
30
122
94
72
1.2
3.0
0.6
1.75
0.49
1.0
0.28
421
132
332
66
193
54
110
31
Burner
Calibrated orifice 1/100mm
Auxiliary
31
Semi-rapid
34
Rapid
43
60
- Aeration adjustment none
27
11.3
-
3.8
Triple-Crown
11.3
-
3.8
137
11.3
-
3.8
128
11.3
-
3.8
135
11.3
-
3.8
98
Total
65
11.3
Download PDF

advertising