Samsung | DVD-P450 | Samsung DVD-P450 User Manual

00708H_P450_XSA/RAD_eng_Cover
2/26/05
11:22 PM
Page 3
DVD Player
DVD-P450
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 2
Precautions
1. Setting up
- Refer to the identification label located on the rear of your
player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation
holes. (7~10cm) Do not block ventilation holes on any of the
components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before moving the player.
- Before connecting other components to this player, be sure
to turn them off.
- Be sure to remove the disc and turn off the player after use,
especially if you don’t use it for a long time.
EZ VIEW
STANDBY/ON
PLAY
EZ VIEW
STANDBY/ON
LOADING
PLAY
EZ VIEW
STANDBY/ON
LOADING
PLAY
LOADING
2. For your safety
- This product utilizes a laser. Use of controls or adjustments
or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
- Do not open covers and do not repair yourself.
Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use but for domestic
purposes. Use of this product is for personal use only.
- Do not put any container filled with liquid or any small metal
objects on the player.
- Exterior influences such as lightning and static electricity can
affect normal operation of this player. If this occurs, turn the
player off and on again with the POWER button, or
disconnect and then reconnect the AC power cord to the AC
power outlet. The player will operate normally.
- When condensation forms inside the player due to sharp
changes in temperature, the player may not operate
correctly. If this occurs, leave the player at room temperature
until the inside of the player becomes dry and operational.
4. Disc
- Do not use record-cleaning sprays, benzene, thinner, or
other volatile solvents that may cause damage to the disc
surface.
- Do not touch the disc’s signal surface. Hold by the edges or
by one edge and the hole in the center.
- Wipe the dirt away gently; never wipe a cloth back and forth
over the disc.
ENG-2
STANDBY/ON
EZ VIEW
PLAY
LOADING
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 3
5. Environmental info
- The battery used in this product contains chemicals that
are harmful to the environment.
- So, dispose of batteries in the proper manner, according to
federal, state, and local regulations.
The product unit accompanying this user manual is licensed under certain intellectual property
rights of certain third parties. This license is limited to private non-commercial use by end-user
consumers for licensed contents. No rights are granted for commercial use. The license does not
cover any product unit other than this product unit and the license does not extend to any
unlicensed product unit or process conforming to ISO/OUR 11172-3 or ISO/OUR 13818-3 used or
sold in combination with this product unit. The license only covers the use of this product unit to
encode and/or decode audio files conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No
rights are granted under this license for product features or functions that do not conform to the
ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
ENG-3
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 4
Before you start
Accessories
Remote
Control
User’s Manual
Batteries for
Remote Control
(AAA Size)
Install Batteries in the Remote control
1
Open the battery
cover on the back of
the remote control.
2
Insert two AAA batteries.
Make sure that the
polarities (+ and -) are
aligned correctly.
3
Replace the battery
cover.
If the remote control doesn’t operate properly:
- Check the polarity + - of the batteries (Dry-Cell)
- Check if the batteries are drained.
- Check if remote control sensor is blocked by obstacles.
- Check if there is any fluorescent lighting nearby.
ENG-4
Video/Audio
Cable
00708H_P450_XSA/RAD_eng_1
2/26/05
TA B L E
OF
11:26 PM
Page 5
CONTENTS
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 1: Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 2: Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 3: Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the Search and Skip Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the Display Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using the Disc and Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using the Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Slow Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Program Play & Random Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Chapter 4: Advanced Functions
Adjusting the Aspect Ratio (EZ View). . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Selecting the Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Selecting the Subtitle Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changing the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Using the Instant Replay/Skip Function . . . . . . . . . . . . . . . . . . . . . . . . . 31
Using the Bookmark Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the Zoom Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
How to insert a Memory Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
DVD AUDIO Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Clips Menu for MP3/WMA/JPEG/MPEG4 . . . . . . . . . . . . . . . . . . . . . . . 39
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
MP3/WMA Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Chapter 5: Changing Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Setting Up the Language Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Setting Up the Audio Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Setting Up the Display Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Setting Up the Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Chapter 6: Reference
Firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
ENG-5
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 6
Chapter 1
SETUP
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound
reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Program Play (CD)
You can program tracks to play in desired order.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional
interlaced picture.
Note
- Discs which cannot be played with this
player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• Super Audio CD(except CD layer)
• CDGs play audio only, not graphics.
- Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy
protection. Because of this, you should only connect
your DVD player directly to your TV, not to a VCR.
Connecting to a VCR results in a distorted picture
from copy-protected DVD discs.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
MP3/WMA
This unit can play discs created from MP3/WMA files.
PROGRESSIVE SCAN OUTPUTS
EZ VIEW (DVD)
Easy View enables picture adjustment to match your
TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Instant Replay (DVD)
This function is used to replay the previous 10
seconds of a movie from the current position.
Instant Skip (DVD)
This function skips playback ahead 10 seconds.
MPEG4
This unit can play MPEG4 formats within an avi file.
DVD AUDIO
DVD AUDIO is a format specifically designed to provide
the highest possible audio fidelity capable on DVD.
(525p/625p)
“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IN CASE OF 525 OR 625 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS RECOMMENDED
THAT THE USER SWITCH THE CONNECTION TO
THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE
ARE QUESTIONS REGARDING YOUR TV SET
COMPATIBILITY WITH THIS MODEL 525p AND 625p
DVD PLAYER, PLEASE CONTACT SAMSUNG'S
CUSTOMER SERVICE CENTER.”
Memory Card
Multi card slot to support 10 types of memory cards:
Memory Stick, Memory Stick-Pro, Memory Stick Duo,
SD, Mini SD Card and XD-Picture Card, MMC,
RS-MMC, Smart Media Card, Compact Flash.
ENG-6
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 7
SETUP
Setup
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Disc Types (Logos)
Recording Types
DVD
Audio
+
Video
VIDEO-CD
Audio
+
Video
AUDIO-CD
Disc Size
Max. Playing Time
12 Cm
Single-sided 240 min.
Double-sided 480 min.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
12 Cm
74 min.
Audio
+
Video
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
12 Cm
400 min.
Disc Markings
~
PAL
DIGITAL
SOUND
- CD is recorded as a Digital Signal with
better audio quality, less distortion and
less deterioration of audio quality over
time.
- DVD AUDIO is a format specifically
designed to provide the highest
possible audio fidelity capable on
DVD.
Region Number
Play Region Number
PAL broadcast system in U.K, France, Germany, etc.
Dolby Digital disc
STEREO
- DVD contains excellent sound and
video due to Dolby Digital and
MPEG-2 system.
- Various screen and audio functions
can be easily selected through the
on-screen menu.
- Video with CD sound, VHS quality &
MPEG-1 compression technology.
Audio
DVD-AUDIO
Characteristics
Stereo disc
Digital Audio disc
Both the DVD player and the discs are
coded by region. These regional
codes must match in order for the disc
to play. If the codes do not match, the
disc will not play.
The Region Number for this player
is described on the rear panel of the
player.
DTS disc
DivX Certification
MP3 disc
DVD AUDIO disc
You must only insert one DVD disc at a time.
Inserting two or more discs will not allow
playback and may cause damage to the DVD
player.
ENG-7
DivX, DivX Certified, and
associated logos are
trademarks of DivXNetworks,
Inc and are used under
license.
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 8
SETUP
Description
Front Panel Controls
9
1
2
3
1.
STANDBY/ON (
)
When the unit is first plugged in, the indicator lights. When
STANDBY/ON is pressed on, the indicator goes out and
the player is turned on.
2.
DISC TRAY
Place the disc here.
3.
OPEN/CLOSE (
)
Press to open and close the disc tray.
4.
DISPLAY
Operation indicators are displayed here.
5.
MULTI CARD INPUT
Insert a Memory Card.
4
2.
Total playing time/Displays various
messages concerning operations
such as PLAY, STOP, LOAD ...
no dISC: No disc loaded.
OPEN: The disc tray is open.
LOAd: Player is loading disc information.
7
8
EZ VIEW
The aspect ratio of a picture can easily be adjusted to
your TV's screen size (16:9 or 4:3).
7.
STOP (
)
Stops disc play.
8.
SKIP (
) / SEARCH
Use to forward skip a scene or music.
9.
SKIP (
) / SEARCH
Use to reverse skip a scene or music.
10. PLAY/PAUSE (
)
Begin or pause disc play.
1
Chapter/Track number indicator
6
6.
Front Panel Display
1.
5
10
2
ENG-8
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 9
SETUP
Setup
Rear Panel
1
1
2
3
4
1.
DIGITAL AUDIO OUT JACKS
- Use either an optical or coaxial digital cable to connect
to a compatible Dolby Digital receiver.
- Use either an optical or coaxial digital cable to connect
to an A/V Amplifier that contains a Dolby Digital,
MPEG2 or DTS decoder.
2.
COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide PR, PB and Y video.
- If Component(P-SCAN) Video Output is selected in
Setup Menu, progressive scan mode will work.
- If Component(I-SCAN) Video Output is selected in
Setup Menu, interlaced scan mode will work.
3.
AUDIO OUT JACKS
Connect to the Audio input jacks of your television or
audio/video receiver.
5
4.
VIDEO OUT JACK
- Use a video cable to connect to the Video input jack on
your television.
- The Video Output in Setup Menu must be set to
COMPOSITE/S-VIDEO.
5.
S-VIDEO OUT JACK
- Use the S-Video cable to connect this jack to the
S-Video jack on your television for higher picture
quality.
- The Video Output in Setup Menu must be set to
COMPOSITE/S-VIDEO.
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan(P-SCAN).
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the
TV’s menu system.
- If Component(P-SCAN) Video Output is selected in Setup Menu, Video and S-Video Outputs do not work.
- See pages 53 ~ 54 to get more information on how to use the setup menu.
ENG-9
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 10
SETUP
Tour of the Remote Control
1
11
1.
DVD POWER Button
Turns the power on or off.
2.
NUMBER Buttons
3.
PROG Button
Allows you to program a specific order.
4.
STEP Button
Advances play one frame at a time.
5.
SEARCH/SKIP Buttons (
,
/
/
Allow you to search forward/backward through a disc.
Use to skip the title, chapter or track.
6.
STOP Button (
7.
MENU Button
Brings up the DVD player’s menu.
8.
RETURN Button
Returns to a previous menu.
9.
DVD/M.CARD button
Use to operate DVD/M.CARD.
2
3
4
12
13
14
5
6
7
15
16
8
17
18
)
)
10. SUBTITLE Button
11. OPEN/CLOSE (
) Button
To open and close the disc tray.
12. CLEAR Button
Use to remove menus or status displays from the screen.
9
19
10
20
21
22
13. INSTANT REPLAY Button
This function is used to replay the previous 10 seconds of a
movie from the current position.
14. INSTANT SKIP Button
This function skips playback ahead 10 seconds.
15. PLAY/PAUSE Button (
Begin/Pause disc play.
)
16. INFO Button
Displays the current disc mode.
17. DISC MENU Button
Brings up the Disc menu.
…†œ√ Buttons
18. ENTER/…
This button functions as a toggle switch.
19. EZ VIEW Button
The aspect ratio of a picture can easily be adjusted according
to the screen size of your TV (16:9 or 4:3).
20. REPEAT Button
Allows you to repeat play a title, chapter, track, or disc.
21. ANGLE Button
Use to access various camera angles on a DVD.
22. AUDIO Button
Use this button to access various audio functions on a disc.
ENG-10
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 11
Chapter 2
CONNECTIONS
Choosing a Connection
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any
cables.
- Refer to the user’s manual of the additional components (such as a TV) you are connecting for
more information on those particular components.
Connection to a TV (Video)
1
Using video/audio cables, connect the VIDEO (yellow)/AUDIO
(red and white) OUT terminals on the rear of the DVD player to
the VIDEO (yellow)/AUDIO (red and white) IN terminals of
your TV.
2
Turn on the DVD player and TV.
WHITE
RED
Audio
Cable
RED
WHITE
YELLOW
Video
Cable
YELLOW
3
Press the input selector on your TV remote control until the
Video signal from the DVD player appears on the TV screen.
Note
- Noise may be generated if the audio cable placed too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 15 to 16)
- The number and position of terminals may vary depending on your TV set. Please refer to the user's manual
of your TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD
player.
ENG-11
Connections
The following shows examples of connections commonly used to connect the DVD player with a TV
and other components.
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 12
CONNECTIONS
Connection to a TV (S-Video)
- Connecting to your TV using an S-Video cable.
- You will enjoy high quality images. S-Video separates the picture element into black and white(Y)
and color(C) signals to present clearer images than regular video input mode. (Audio signals are
delivered through the audio output.)
1
Using an S-Video cable (not included), connect the S-VIDEO
OUT terminal on the rear of the DVD player to the
S-VIDEO IN terminal of your TV.
2
Using the audio cables, connect the AUDIO (red and white)
OUT terminals on the rear of the DVD player to the AUDIO (red
and white) IN terminals of your TV.
Turn on the DVD player and TV.
RED
3
Press the input selector on your TV remote control until the SVideo signal from the DVD player appears on your TV screen.
WHITE
Audio Cable
RED
S-Video Cable
(not included)
WHITE
4
Set the Video Output to COMPOSITE/S-VIDEO in the Display
Setup menu. (See pages 53 to 54)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 15 to 16)
- The number and position of terminals may vary depending on the TV set.
Please refer to the user's manual of your TV.
ENG-12
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 13
CONNECTIONS
Connection to a TV (Interlace)
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminals on the rear of the DVD
player to the COMPONENT IN terminals of your TV.
2
Using the audio cables, connect the AUDIO (red and white)
OUT terminals on the rear of the DVD player to the AUDIO (red
and white) IN terminals of your TV.
Turn on the DVD player and TV.
RED
3
RED
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
BLUE
GREEN
WHITE
Audio Cable
RED
WHITE
RED BLUE
GREEN
Component cable
(not included)
4
Set the Video Output to Component(I-SCAN) in the Display
Setup menu. (See pages 53 to 54)
Note
- If Video output is incorrectly set to COMPOSITE/S-VIDEO with the Component cables connected, the
screen will turn red.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 15 to 16)
- The component terminal of your TV may be marked “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y”
depending on the manufacturer. The number and position of terminals may vary depending on the TV set.
Please refer to the user's manual of your TV.
ENG-13
Connections
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates
the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean
images. (Audio signals are delivered through the audio output.)
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 14
CONNECTIONS
Connection to a TV (Progressive)
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminals on the rear of the DVD
player to the COMPONENT IN terminals of your TV.
2
Using the audio cables, connect the AUDIO (red and white)
OUT terminals on the rear of the DVD player to the AUDIO (red
and white) IN terminals of your TV.
Turn on the DVD player and TV.
RED
3
RED
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
BLUE
GREEN
WHITE
Audio Cable
RED
WHITE
RED BLUE
GREEN
Component cable
(not included)
4
Set the Video Output to Component(P-SCAN) in the Display
Setup menu. (See pages 53 to 54)
To see the progressive video output,
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings
in the TV’s menu system.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method.
Progressive scanning method provides better and clearer picture quality.
ENG-14
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 15
CONNECTIONS
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and white)
OUT terminals on the rear of the DVD player to the AUDIO (red
and white) IN terminals of the Amplifier.
Connections
2
Using the video signal cable(s), connect the VIDEO, S-VIDEO
or COMPONENT OUT terminals on the rear of the DVD player
to the VIDEO, S-VIDEO or COMPONENT IN terminal of your
TV as described on pages 11 to 14.
3
RED
Turn on the DVD player, TV, and Amplifier.
WHITE
Audio Cable
RED
WHITE
2-Channel stereo amp
4
Press the input select button of the Amplifier to select external
input in order to hear sound from the DVD player.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier.(See pages 51 to 52)
- The position of terminals may vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
ENG-15
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 16
CONNECTIONS
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
If using an optical cable (not included), connect the DIGITAL
AUDIO OUT (OPTICAL) terminal on the rear of the DVD player
to the DIGITAL AUDIO IN (OPTICAL) terminal of the Amplifier.
If using a coaxial cable (not included), connect the DIGITAL
AUDIO OUT (COAXIAL) terminal on the rear of the DVD player
to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO, S-VIDEO
or COMPONENT OUT terminals on the rear of the DVD player
to the VIDEO, S-VIDEO or COMPONENT IN terminal of your
TV as described on pages 11 to 14.
or
3
Coaxial Cable
(not included)
Optical Cable
(not included)
Turn on the DVD player, TV, and Amplifier.
Dolby digital or
DTS amp
4
Press the input select button of the Amplifier to select external
input in order to hear sound from the DVD player.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Note
- When you connect the DVD player to DTS Amplifier and play a DTS disc, set the DTS to On in Audio
Setup menu. If it is set to Off, sound will not be heard, or there will be a loud sound.
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 51 to 52)
- The position of terminals may vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
ENG-16
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 17
Chapter 3
BASIC FUNCTIONS
Playing a Disc
Before Play
- Turn on your TV and set it to the correct Video Input on the TV's remote control.
- If you connected an external Audio System, turn on your Audio System and set it to the correct
Audio Input.
Playback
1
Press the OPEN/CLOSE
( ) button.
The STANDBY indicator
light goes out and the tray
opens.
2
Place a disc gently into the
tray with the disc’s label
facing up.
▼
RESUME function
3
When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE ( ) button again, it will pick up
where you left off. (unless the disc is removed
or the player is unplugged, or if you press the
STOP ( ) button twice.)
Press the PLAY/PAUSE ( )
button or OPEN/CLOSE ( )
button to close the disc tray.
ENG-17
Basic Functions
After plugging in the player, the first time you press the DVD POWER button, this
screen comes up: If you want to select a language, press a NUMBER button.
(This screen will only appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings may change whenever you
turn the power on or off. Therefore, make sure that you select the language you want to
use.
Once you select a menu language, you can change it by pressing the
button on the
front panel of the unit for more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where you can reset your
preferred language.
00708H_P450_XSA/RAD_eng_1
2/26/05
11:26 PM
Page 18
BASIC FUNCTIONS
4
Stopping Play
Press the STOP ( ) button
during play.
Note
- If the player is left in the stop mode for more than
one minute without any user interaction, a screen
saver will be activated. Press the PLAY/PAUSE
( ) button to resume normal play.
- If the player is left in the stop mode for more than
30 minutes, the power will automatically turn off.
(Automatic Power-Off Function)
5
Removing Disc
Press the OPEN/CLOSE
( ) button.
▼
Screen stops, no sound.
To resume, press the PLAY/PAUSE (
once again.
6
Pausing Play
Press the PLAY/PAUSE
( ) or STEP button on the
remote control during play.
) button
Note
If the player is left for about 5 minutes in pause
mode, it will stop.
Each time the button is pressed, a new frame
will appear.
No sound is heard during STEP mode.
Press the PLAY/PAUSE ( ) button to resume
normal play.
You can only perform step motion play in the
forward direction.
▼
7
Step Motion Play (Except
CD/DVD-AUDIO)
Press the STEP button on
the remote control during
play.
Slow Motion Play (Except
CD/DVD-AUDIO)
Press and hold the
SEARCH ( ) button to
choose the play speed
between 1/8, 1/4 and 1/2 of
normal during PAUSE or
STEP mode.
No sound is heard during slow mode.
Press the PLAY/PAUSE ( ) button to resume
normal play.
Reverse slow motion play will not work.
▼
8
Note
This (
ENG-18
) icon indicates an invalid button press.
00708H_P450_XSA/RAD_eng_1
2/26/05
11:27 PM
Page 19
BASIC FUNCTIONS
Using the Search and Skip Functions
During play, you can search quickly through a chapter or track, and use the skip function to jump to
the next selection.
Searching through a Chapter or Track
▼
If you want to search at a faster speed on the
DVD, VCD, CD or DVD-AUDIO, press and hold
the button.
During play, press the
SEARCH ( or ) button
on the remote control for
more than 1 second.
DVD
2X, 8X, 32X, 128X
VCD
4X, 8X
CD/DVD-AUDIO
2X, 4X, 8X
- The speed marked in this function may be
different from the actual playback speed.
- No sound is hearing during search mode
(Except CD).
Skipping Chapters or Tracks
During play, press the SKIP
(
or
) button.
- When playing a DVD, if you press the SKIP ( )
button, it moves to the next chapter. If you press
the SKIP ( ) button, it moves to the beginning
of the chapter. One more press makes it move to
the beginning of the previous chapter.
- When playing a VCD 2.0 in Menu Off mode, or a
VCD 1.1 or a CD/DVD-AUDIO, if you press the
SKIP ( ) button, it moves to the next track. If
you press the SKIP ( ) button, it moves to the
beginning of the track. One more press makes it
move to the beginning of the previous track.
- If a track exceeds 15 minutes when playing a
VCD and you press the SKIP ( ) button, it
moves forward 5 minutes. If you press the SKIP
( ) button, it moves backward 5 minutes.
Note
When playing VCD 2.0, this function works only
when the menu is off. Select Menu Off by pressing
the DISC MENU button.
ENG-19
Basic Functions
Note
00708H_P450_XSA/RAD_eng_1
2/26/05
11:27 PM
Page 20
BASIC FUNCTIONS
Using the Display Function
When Playing a DVD/VCD/CD/MPEG4
▼
You can select Info in the function menu by
pressing the MENU button.
1
During play, press the
INFO button on the remote
control.
2
DVD
Press the …/† buttons to
select the desired item.
01
02
0:00:13
ENG 5.1CH
Off
▼
VCD
01
0:00:43
CD
01
0:00:48
MPEG4
01
0:00:13
MP3 1/8
On
640x272
ENG-20
When playing VCD 2.0, this function works only
when the menu is off. Select Menu Off by
pressing the DISC MENU button.
00708H_P450_XSA/RAD_eng_1
2/26/05
11:27 PM
Page 21
BASIC FUNCTIONS
▼
You may use the number buttons of the remote
control to directly access a title, chapter or to
start the playback from a desired time.
3
Press the œ/√ buttons to
make the desired setup,
then press the ENTER
button.
4
To make the screen
disappear, press the INFO
button again.
To access the desired title when there is more than one in the disc.
For example, if there is more than one movie on a DVD, each movie will be identified.
Most DVD discs are recorded in chapters so that you can quickly find a specific passage (similar to
tracks on an audio CD).
Allows playback of the film from a desired time. You must enter the starting time as a reference.
The time search function does not operate on some discs.
Refers to the film's soundtrack language. In the example, the soundtrack is played in English
5.1CH.
A DVD disc can have up to eight different soundtracks.
The MP3, AC3 and WMA are supported.(DivX)
Refers to the subtitle languages available in the disc.
You will be able to choose the subtitle languages or, if you prefer, turn them off from the screen.
A DVD disc can have up to 32 different subtitles.
(DivX)
File Size has a relationship with resolution of a title. The larger file size is, the higher resolution is
displayed.
If the file resolution is small, it scales up automatically. So you can see the larger screen.
ENG-21
Basic Functions
Note
00708H_P450_XSA/RAD_eng_1
2/26/05
11:27 PM
Page 22
BASIC FUNCTIONS
Using the Disc and Title Menu
Using the Disc Menu (DVD)
1
During the playback of a
DVD disc, press the MENU
button on the remote
control.
2
Press the …/† buttons to
select Disc Menu, then
press the √ or ENTER
button.
Press ENTER key
for Disc Menu
Note
- Depending on a disc, the Disc Menu may not
work.
- You can also use the Disc Menu, using the DISC
MENU button on the remote control.
- In VCD 2.0 the DISC MENU button is used to
select Menu On or Menu Off mode.
Using the Title Menu (DVD)
1
During the playback of a
DVD disc, press the MENU
button on the remote
control.
2
Press the …/† buttons to
select Title Menu, then
press the √ or ENTER
button.
Press ENTER key
for Title Menu
Note
- Depending on a disc, the Title Menu may not
work.
- Title Menu will only be displayed if there are at
least two titles in the disc.
ENG-22
00708H_P450_XSA/RAD_eng_1
2/26/05
11:27 PM
Page 23
BASIC FUNCTIONS
Using the Function Menu
Using the Function Menu (DVD/VCD)
1
Press the MENU button
during playback.
2
Press the …/† buttons to
select one of the five
functions. Then press the
√ or ENTER button to
access the function.
Info
Zoom
Bookmark
Repeat
EZ View
You can also directly select these functions
using their respective buttons on the remote
control.
▼
3
Basic Functions
Press the …/† buttons to
select Function, then press
the √ or ENTER button.
- Info (See pages 20 to 21)
- Zoom (See page 34)
- Bookmark
(See pages 32 to 33)
- Repeat (See pages 24 to 25)
- EZ View
(See pages 27 to 28)
Note
When playing VCD 2.0, this function works only
when the menu is off. Select Menu Off by pressing
the DISC MENU button.
ENG-23
00708H_P450_XSA/RAD_eng_1
2/26/05
11:27 PM
Page 24
BASIC FUNCTIONS
Repeat Play
Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.
When playing a DVD/VCD/CD
1
Press the REPEAT button
on the remote control.
Repeat screen appears.
DVD repeats play by chapter or title, CD and
VCD repeat play by disc or track.
Chapter ( ): repeats the chapter that is
playing.
Title ( ): repeats the title that is playing.
Disc ( ): repeats the disc that is playing.
Track ( ): repeats the track that is playing.
A-B: repeats a segment of the disc that you
select.
▼
2
DVD
Press the œ/√ buttons to
select Chapter, Title or A-B,
then press the ENTER
button.
Off
01
T
01 A-B
REPEAT
ENTER
01 A-B
REPEAT
ENTER
VCD/CD
Off
T
01
D
Using the A-B Repeat function
1. Press the REPEAT button on the remote control.
2. Press the œ/√ buttons to select A-B.
3. Press the ENTER button at the point where you want repeat play to start (A).
B is automatically highlighted.
4. Press the ENTER button at the point where you want the repeat play to stop (B).
- To return to normal play, press the CLEAR button.
Note
A-B REPEAT does not allow you to set point (B) until at least 5 seconds of playback time has
elapsed after point (A) has been set.
3
To return to normal play,
press REPEAT button
again, then press the œ/√
buttons to select Off and
press ENTER button.
DVD
Off
01
T
01 A-B
REPEAT
ENTER
VCD/CD
Off
T
01
D
01 A-B
REPEAT
ENTER
Note
- Depending on a disc, the Repeat function may
not work.
- When playing VCD 2.0, this function works only
when the menu is off. Select Menu Off by
pressing the DISC MENU button.
ENG-24
00708H_P450_XSA/RAD_eng_1
2/26/05
11:27 PM
Page 25
BASIC FUNCTIONS
Slow Repeat Play
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments
being played etc., so you can study them more closely.
When playing a DVD/VCD
1
During play, press the
PLAY/PAUSE ( ) button.
Basic Functions
2
Press and hold the
SEARCH ( ) button to
choose the play speed
between 1/8, 1/4 and 1/2 of
normal during PAUSE or
STEP mode.
▼
The disc will play from A to B repeatedly at the
speed you chose.
▼
3
To set A-B REPEAT, set (A) first, then set (B)
after the following slow play time has elapsed:
1/8x: wait 40 seconds, then press B
Press the REPEAT button
on the remote control.
Press the œ/√ buttons to
select A-B.
4
Press the ENTER button at
the point where you want
repeat play to start (A).
B is automatically
highlighted. Press the
ENTER button at the point
where you want the repeat
play to stop (B).
1/4x: wait 20 seconds, then press B
1/2x: wait 10 seconds, then press B
5
To return to normal play,
press the CLEAR button
and then press the
PLAY/PAUSE ( ) button.
Note
When playing VCD 2.0, this function works only
when the menu is off. Select Menu Off by pressing
the DISC MENU button.
ENG-25
00708H_P450_XSA/RAD_eng_1
2/26/05
11:27 PM
Page 26
BASIC FUNCTIONS
Program Play & Random Play
Program Play (CD)
Program Play allows you to select the order in which you want tracks to play.
1
During play, press the
PROG button.
2
Press the œ/√ buttons to
select PROGRAM.
Press the ENTER button.
PROGRAM
œ√
RANDOM
▼
3
Press the …/†/œ/√ buttons
to select the first track to
add to the program.
Press the ENTER button.
The selection numbers
appear in the Program
Order box.
PROGRAM 01
Track
01
05
09
13
02
06
10
14
03
07
11
15
Program Order
04
08
12
16
------
------
------
------
- To return to the previous menu screen, press
the RETURN button.
- To cancel the selected program order, press
the CLEAR button.
- This unit can support a maximum of 20
programmed tracks.
4
Press the PLAY/PAUSE
( ) button.
The disc will be played in
programmed order.
Random Play (CD)
Random Play plays a disc's tracks in random order.
1
Press the PROG button.
2
Press the œ/√ buttons to
select RANDOM.
Press the ENTER button.
PROGRAM
œ√
RANDOM
Note
- Depending on a disc, the Program and Random
Play functions may not work.
- While in playback mode, press the CLEAR button
on the remote control to cancel Program Play or
Random Play.
ENG-26
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 27
Chapter 4
A D VA N C E D F U N C T I O N S
Adjusting the Aspect Ratio (EZ View)
To play back using aspect ratio (DVD)
▼
Press the EZ VIEW
button.
- The screen size
changes when the
button is pressed
repeatedly.
- The screen zoom mode
operates differently
depending on the screen
setting in the Display
Setup menu.
- To ensure correct
operation of the EZ
VIEW button, you should
set the correct aspect
ratio in the Display
Setup menu.
(See pages 53 to 54).
WIDE SCREEN
EZ VIEW
To make the aspect ratio bar disappear,
press the CLEAR button.
If you are using a 16:9 TV
For 4:3 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
ENG-27
Advanced
Functions
For 16:9 aspect ratio discs
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 28
A D VA N C E D F U N C T I O N S
If you are using a 4:3 TV
For 16:9 aspect ratio discs
For 4:3 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio.
The black bars will appear at the top and bottom of the
screen.
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- 4:3 Pan Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears.
The picture will look vertically stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
Note
This function may behave differently depending on the type of disc.
ENG-28
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 29
A D VA N C E D F U N C T I O N S
Selecting the Audio Language
You can select a desired audio language quickly and easily with the AUDIO button.
Using the AUDIO button (DVD/VCD/CD/MPEG4)
1
Press the AUDIO button.
The Audio changes when
the button is pressed
repeatedly.
- The audio languages
are represented by
abbreviations.
DVD
ENG DOLBY DIGITAL 5.1CH
AUDIO
VCD/CD
When playing a VCD or CD,
you can select among
Stereo, Right or Left.
2
To remove the AUDIO
icon, press the CLEAR or
RETURN button.
AUDIO
Advanced
Functions
√ buttons to
Press the œ/√
select the desired Audio on
a MPEG4 then press the
ENTER .
Stereo
MPEG4
PCM 1/2
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio
languages.
- To have the same audio language come up
whenever you play a DVD; Refer to “Using the
Audio Language” on page 49.
ENG-29
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 30
A D VA N C E D F U N C T I O N S
Selecting the Subtitle Language
You can select a desired subtitle quickly and easily with the SUBTITLE button.
Using the SUBTITLE button (DVD/MPEG4)
1
Press the SUBTITLE
button.
The subtitle changes when
the button is pressed
repeatedly.
The subtitle languages are
represented by
abbreviations.
DVD
Off
√ buttons to
Press the œ/√
select the desired subtitle
language on a MPEG4 then
press the ENTER .
2
To remove the SUBTITLE
icon, press the CLEAR or
RETURN button.
SUBTITLE
MPEG4
1/8
Note
- Depending on DVDs, you can change the
desired subtitle in the Disc Menu. Press the
DISC MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all
DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD;
Refer to “Using the Subtitle Language” on page
50.
ENG-30
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 31
A D VA N C E D F U N C T I O N S
Changing the Camera Angle
When a DVD contains multiple angles of a particular scene, you can use the ANGLE
function.
Using the ANGLE button (DVD)
If the disc contains multiple angles, the ANGLE appears on the screen.
1
Press the ANGLE button,
then the ANGLE icon will
appear with the current
angle number and the
number of angles
available.
2
4/6
ANGLE
Press the ANGLE button
repeatedly to select the
desired angle. To remove
the ANGLE icon, press the
CLEAR or RETURN
button.
Note
If the disc has only one angle, this feature won’t
work. Currently, very few discs have this
feature.
Using the Instant Replay function (DVD)
If you miss a scene, you can see it again using this function.
Press the INSTANT
REPLAY button.
- The current scene
moves backward about
10 seconds, and plays
back.
Using the Instant Skip function (DVD)
Use this function to skip playback about 10 seconds ahead of the current scene.
Press the INSTANT SKIP
button.
- Playback will skip ahead
10 seconds.
Note
Depending on the disc, these functions may not
work.
ENG-31
Advanced
Functions
Using the Instant Replay/Skip Function
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 32
A D VA N C E D F U N C T I O N S
Using the Bookmark Function
This feature lets you bookmark sections of a DVD or VCD (Menu Off mode) so you can quickly find
them at a later time.
Using the Bookmark Function (DVD/VCD)
1
During play, press the
MENU button on the
remote control.
2
† buttons to
Press the …/†
select Function, then
press the √ or ENTER
button.
Info
Zoom
Bookmark
Repeat
EZ View
3
† buttons to
Press the …/†
select Bookmark, then
press the √ or ENTER
button.
Info
Zoom
Bookmark
Repeat
EZ View
4
When you reach the
scene you want to mark,
press the ENTER button.
Up to three scenes may
be marked at a time.
Note
- When playing VCD 2.0, this function works only
when the menu is off. Select Menu Off by
pressing the DISC MENU button.
- Depending on a disc, the Bookmark function may
not work.
ENG-32
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 33
A D VA N C E D F U N C T I O N S
Recalling a Marked Scene
1~3
The first 1~3 steps are the
same as those for “Using
the Bookmark Function”
on page 32.
4
Press the œ/√ buttons to
select a marked scene.
5
Press the PLAY/PAUSE
(
) button to skip to
the marked scene.
Advanced
Functions
Clearing a Bookmark
1~3
The first 1~3 steps are the
same as those for “Using
the Bookmark Function”
on page 32.
4
Press the œ/√ buttons to
select the bookmark
number you want to delete.
5
Press the CLEAR button
to delete a bookmark
number.
ENG-33
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 34
A D VA N C E D F U N C T I O N S
Using the Zoom Function
Using the Zoom Function (DVD/VCD)
1
During play or pause
mode, press the MENU
button on the remote
control.
2
† buttons to
Press the …/†
select Function, then
press the √ or ENTER
button.
Info
Zoom
Bookmark
Repeat
EZ View
3
† buttons to
Press the …/†
select Zoom, then press
the √ or ENTER button.
Info
Zoom
Bookmark
Repeat
EZ View
▼
4
† or œ/√
Press the …/†
buttons to select the part
of the screen you want to
zoom in on.
Press the ENTER button.
During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
During VCD play, press ENTER to zoom in
2X/Normal in order.
Note
When playing VCD 2.0, this function works only
when the menu is off. Select Menu Off by pressing
the DISC MENU button.
ENG-34
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 35
A D VA N C E D F U N C T I O N S
How to insert a Memory Card
This unit accepts 10 different types of Memory Cards
Insert the Memory Card correctly with the label facing up, otherwise it may not work.
Multi card slot to support 10 types of memory cards: Memory Stick, Memory Stick-Pro, Memory Stick Duo,
SD, Mini SD Card and XD-Picture Card, MMC, RS-MMC, Smart Media Card, Compact Flash.
When cards are inserted in two slots, the card which is inserted first has a priority on playback.
Note
- If it is not fully inserted, the “Memory Card” will not work. Some memory cards may not be perfomed
correctly.
- If you remove the “Memory Card” during Memory Card operation, the recorded data may become
corrupted. It is better to remove it after pressing DVD/M.CARD button to return to DVD/CD Mode.
- DVD/CD cannot be played in the Memory Card mode. If you press the DVD/M.CARD or OPEN/CLOSE
button in M.CARD mode, the system will automatically enter the DVD/CD mode.
- When pressing the DVD/M.CARD button to play the disc again, the player doesn’t remember where you
stopped.
When playing a Memory Card
1
Insert a Memory Card.
2
Press the DVD/M.CARD
button on the remote
control.
3
Depending on the file type stored on the Memory card,
audio files will be played the same way as MP3/WMA files
and picture files will be played the same way as Picture
CD’s files. (See pages 39 to 45)
ENG-35
Advanced
Functions
- Memory Stick Duo, Mini SD, and RS-MMC must be inserted into a slot using adapter. But some Memory
cards may not be performed correctly depending on the adapter condition.
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 36
A D VA N C E D F U N C T I O N S
DVD AUDIO Playback
1
Open the disc tray.
Place the DVD AUDIO disc on the tray.
- Place the DVD AUDIO disc with the labeled side up.
Close the tray.
- The tray closes and disc plays.
▼
You can select Info in the function menu by
pressing the MENU button.
2
During play, press the INFO
button on the remote
control.
3
Press the …/† buttons to
select the desired item.
DVD-AUDIO
01
01
01
0:00:13
▼
You may use the number buttons of the remote
control to directly access a Group, Track, Page
or to start the playback from the desired time.
4
Press the œ/√ buttons to
make the desired setup and
then press the ENTER
button.
5
To make the screen
disappear, press the INFO
button again.
ENG-36
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 37
A D VA N C E D F U N C T I O N S
Note
Most DVD AUDIO discs are recorded in Groups you can change Groups with this Function.
Bonus Group playback.
Some DVD AUDIO discs have Bonus groups. If you want to play a Bonus group, you must enter the
Bonus Group code. The code is usually on the DVD AUDIO disc case.
To access the desired Track when there is more than one on the DVD AUDIO disc.
If pages are included with the DVD-AUDIO disc, you can see this icon.
To access the desired page, you can use this Function.
Slide
V-zone
If a slide show is included with the DVD-AUDIO disc, you can see this icon.
If a video zone is included with the DVD-AUDIO disc, you can see this icon.
Allows playback of music from a desired time by using the number buttons.
Page, Index Function
Note
Depending on a disc, this function may not work.
Use Page icon of display
function to skip the Page
when there is more than one
in a group.
- Some DVD-AUDIO discs
include a slide show. In the
slide show mode, this
function can not be used.
- PAGE is still images.
You can see the still
images when a DVDAUDIO disc is played back.
ENG-37
Advanced
Functions
1
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 38
A D VA N C E D F U N C T I O N S
Repeat Play
1
Press the REPEAT button
on the remote control.
Repeat screen appears.
Press the œ/√ buttons to
select Title, Group, then
press the ENTER button.
Title ( ): repeats the title that is playing.
Group ( ): repeats the group that is playing.
▼
2
DVD-AUDIO
Off
01
01
AUDIO Format Display
1
During DVD AUDIO
playback, press the AUDIO
button to see AUDIO Format
information.
▼
DVD-AUDIO
PPCM 5.1CH
- LPCM : Linear Pulse Code Modulation.
Not compressed Audio data format.
- PPCM : Packet Pulse Code Modulation.
Lossless compressed Audio data
format.
Note
Some DVD-AUDIO discs don’t allow audio
down-mixing.
ENG-38
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 39
A D VA N C E D F U N C T I O N S
Clips Menu for MP3/WMA/JPEG/MPEG4
Discs with MP3/WMA/JPEG/MPEG4 contain individual songs and/or pictures that
can be organized into folders as shown below. They are similar to how you use your
computer to put files into different folders.
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
Off
ROOT
ROOT
WMA
JPEG
MP3
MPEG4
Parent Folder, Current Folder Folders and Files in
Current Folder
and Peer Folders
: Name of currently playing file.
-
: MP3 file icon.
-
: Current Playback Time.
-
: WMA file icon.
-
: Current Playback Mode : There are four
modes. They can be selected in order by
pressing the REPEAT button.
- Off: Normal Playback
- Track: Repeats the current track.
- Folder: Repeats the current folder.
- Random: Files in the disc will be played
in random order.
-
: JPEG file icon.
-
: AVI file icon.
-
: Folder icon.
-
: Current Folder icon.
-
: Disc mode (
: Memory Card Mode)
Folder Selection
The folder can only be selected in the Stop mode.
- To select the Parent Folder
Press the RETURN button to go to the parent folder,
† buttons to select “..” and
or press the …/†
press ENTER to go to the parent folder.
- To select the Peer Folder
Press the œ/√ buttons to highlight the left window.
† buttons to select the desired folder,
Press the …/†
then press ENTER.
Root
WMA
JPEG
Parent Folder
MP3
MUSIC
- To select the Sub-Folder
Press the œ/√ buttons to highlight the right window.
† buttons to select the desired folder,
Press the …/†
then press ENTER.
Current Folder
1st
Sub-Folders
2nd
SONG FILE 1
Peer Folders
SONG FILE 2
SONG FILE 3
MPEG4 FILES
ENG-39
Advanced
Functions
-
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 40
A D VA N C E D F U N C T I O N S
MP3/WMA Playback
1
Open the disc tray.
Place the disc on the tray.
Close the tray.
Off
ROOT
ROOT
WMA
JPEG
MP3
MPEG4
▼
2
† or œ/√
Press the …/†
buttons to select a song
file.
Press ENTER to begin
playback of the song file.
When a disc that contains both MP3 and
WMA files, only one type will play, not
both.
Off
00:00:23
B e c a u s e Yo u
RO
OO
OT
T
R
. .O O T
R
WMA
B eMcAa u s e Y o u
W
JPEG
tus
JCPaEc G
MP3
Sa
M
P d3 D a y u
MPEG4
Wonderful
MPEG4
Note
- Depending on the recording method, some MP3 CD-Rs may not be played.
- It is impossible to write MP3 or JPEG files to a Memory Card in this unit as it is read only.
- Only MP3/WMA Format files with the “ .mp3 and .wma” extensions can be played.
Repeat/Random playback
1
Press the REPEAT button
to change the playback
mode. There are four
modes; Off, Track, Folder
and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same extension
in the current folder.
- Random: Song files which have the same extension will be
played in random order.
To resume normal play, press the CLEAR button.
ENG-40
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 41
A D VA N C E D F U N C T I O N S
MP3/WMA file
When you record MP3 or WMA files on CD-R/Memory Card, please refer to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used. Memory
Card over 4GB use FAT32, which may not be compatible
with this unit.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file
extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters
or less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following
types: Windows MediaTM (registered trade mark of Microsoft
Inc) and SDMITM (registered trade mark of The SDMI
Foundation). You cannot copy such files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or
as an assurance of sound quality. You should note that
certain technologies and methods for MP3 file recording on
CD-Rs prevent optimal playback of these files on your DVD
player (degraded sound quality and in some cases, inability
of the player to read the files).
- This unit can play a maximum of 3000 files and 300 folders
per disc.
ENG-41
Advanced
Functions
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate
of compression/decompression you choose. Getting CD
audio sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to
160 Kbps. However, choosing higher rates, like 192
Kbps or more, only rarely give better sound quality.
Conversely, files with decompression rates below 128 Kbps
will not be played properly.
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate
of compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps.
Conversely, files with decompression rates below 64Kbps
or over 192Kbps will not be played properly.
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 42
A D VA N C E D F U N C T I O N S
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video data. Only AVI format files with the
“.avi” extensions can be played.
1
Open the disc tray.
Place the disc on the tray.
Close the tray.
Off
ROOT
ROOT
WMA
JPEG
MP3
MPEG4
2
† or œ/√
Press the …/†
buttons to select an avi file
(DivX/XviD), then press the
ENTER button.
Off
ROOT
R
. .O O T
WMA
WMA
JPEG
JPEG
MP3
MP3
MPEG4
MPEG4
Repeat Play
1
Press the REPEAT button
to change playback mode.
There are 4 modes, such
as Off, Folder, Title and
A-B .
- Off: Normal Playback
- Folder : Repeats the AVI files which have the same extension
in the current folder.
- Title : repeats the title that is playing.
- A-B : repeats a segment of the file that you select.
ENG-42
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 43
A D VA N C E D F U N C T I O N S
MPEG4 Function Description
Function
Description
During play, press the
or
Skip
button, it moves forward
(
or
)
or backward 5 minutes.
During play, press and hold
SEARCH ( or ) button to
Search
(
or
) search at a faster speed.
(2X,4X,8X)
Allows you to search at a
Slow Motion slower speed in an AVI file.
Play
(1/8X, 1/4X, 1/2X)
Each time the STEP button
Step Motion is pressed, a new frame will
Play
appear.
ZOOM
2X/4X/2X/Normal in order
CD-R AVI file
Reference page
-
-
This unit can play the following video compression formats
within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG4 Simple Profile)
- DivX 5 contents (MPEG4 simple profile plus additional
features such as bi-directional frames. Qpel and GMC are
also supported.)
- XviD MPEG4 compliant Contents.
P 18
This unit supports all resolutions up to maximum below.
P 18
P 34
- These functions may not work depending on MPEG4 file.
DivX3.11 & DivX4 & XviD
DivX5
Bitrate may fluctuate:
Device may skip decoding
the high bitrate portions
and begin decoding again
when Bitrate returns to
normal.
720 x 480 @30fps
720 x 576 @25fps
: Maximum bitrate : 4Mbps
Note
- Some MPEG4 files created on a personal computer may not be played.
That is why Codec Type, Version and Higher resolution over specification is not supported.
- This unit supports subtitle file formats such as .SMI, .SRT, .SUB, .SSA, .ASS, .PSD and .TXT.
ENG-43
Advanced
Functions
- This unit supports CD-R/RW written in MPEG4 in accordance with the “ISO9660 format”.
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 44
A D VA N C E D F U N C T I O N S
Picture CD Playback
Off
1
Select the desired folder.
ROOT
ROOT
WMA
JPEG
MP3
MPEG4
2
Off
† buttons to
Press the …/†
select a Picture file in the
clips menu, then press the
ENTER button.
ROOT
..
WMA
1
JPEG
2
MP3
3
MPEG4
3
Note
- If no buttons on the remote control are pressed
for 10 seconds, the menu will disappear.
ENTER RETURN
Press the INFO button to
display the menu.
Press the œ/√ buttons to
select the menu you want
to view, then press the
ENTER button.
- Press the STOP button to return to the clips
menu.
- When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
Slide Show
Album Screen
•
TIMER:
: Returns to the Album Screen.
• To see the next six pictures, press the
• To see the previous six pictures, press the
ENTER RETURN
button.
button.
Rotation
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
Zoom
† or œ/√ buttons to select the
: Press the …/†
part of the screen you want to zoom in on.
Press the ENTER button. Each time the ENTER
button is pressed, the picture is enlarged up
to 4X. (2X ➝ 4X ➝ 2X ➝ Normal)
•
: The unit enters slide show mode.
• Before beginning the Slide Show, the picture interval must be
set. Press the œ/√ buttons to select a desired icon, then
press the ENTER button.
•
: The pictures change automatically with about a 6
second interval.
•
: The pictures change automatically with
about a 12 second interval.
•
: The pictures change automatically with
about a 18 second interval.
Note
- Depending on a file size, the amount of time between each picture may be different from the set interval
time.
- If you don’t press any button, the slide show will start automatically in about 10 seconds by default.
ENG-44
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 45
A D VA N C E D F U N C T I O N S
JPEG Discs
When playing a CD-R/Memory Card/Picture CD
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
- Some memory cards may not be perfomed correctly.
- The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special characters
(. / = +).
- Only a consecutively written multi-session disc can be played. If there is a blank segment in the multi-session disc, the disc can
be played only up to the blank segment.
- A maximum of 3000 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can be played automatically.
- Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 3000, only 3000 JPEG files can be played.
- If the number of folders in 1 Disc is over 300, only JPEG files in 300 folders can be played.
Advanced
Functions
ENG-45
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
Page 46
Chapter 5
CHANGING SETUP
MENU
Using the Setup Menu
The Setup menu lets you customize your DVD player by allowing you to select various language
preferences, set up a parental level, even adjust the player to the type of television screen you
have.
1
With the unit in Stop
mode, press the MENU
button on the remote
control.
† buttons to
Press the …/†
select Setup, then press
the √ or ENTER button.
Setup
Language Setup
√
Audio Setup
√
Display Setup
√
Parental Setup :
√
DivX(R) Registration
√
Language Setup : Setup of the Language.
Audio Setup : Setup of the Audio Options.
Display Setup : Setup of the Display Options. Use to select which type of screen you want to
watch and several display options.
¨ Parental Setup : Setup of the Parental Level. Allows users to set the level necessary to prevent
children from viewing unsuitable movies such as those with violence, adult
subject matter, etc.
ˆ DivX(R) Registration : Please use the Registration code to register this player with the DivX(R)
Video On Demand format. To learn more, go to www.divx.com/vod.
Œ
´
ˇ
2
† buttons to
Press the …/†
access the different
features. Press the √ or
ENTER button to access
the sub features.
3
To make the setup screen
disappear after setting up,
press the MENU button
again.
Note
Depending on the disc, some Setup menu
selections may not work.
ENG-46
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
CHANGING SETUP
Page 47
MENU
Setting Up the Language Features
If you set the player menu, disc menu, audio and subtitle language in advance, they will come up
automatically every time you watch a movie.
Using the Player Menu Language
1
With the unit in Stop
mode, press the MENU
button.
2
† buttons to
Press the …/†
select Setup, then press
the √ or ENTER button.
Setup
Language Setup
√
Audio Setup
√
Display Setup
√
Parental Setup :
√
DivX(R) Registration
√
Language Setup
√
Audio Setup
√
Display Setup
√
Parental Setup :
√
DivX(R) Registration
√
3
† buttons to
Press the …/†
select Language Setup,
then press the √ or
ENTER button.
Setup
4
: English
√
Disc Menu
: English
√
Audio
: English
√
Subtitle
: Automatic
√
▼
5
† buttons to
Press the …/†
select the desired
language, then press the
√ or ENTER button.
PLAYER MENU LANGUAGE
Player Menu
English
- The language is selected and the screen
returns to Language Setup menu.
- To make the setup menu disappear, press the
MENU button.
Français
Deutsch
Español
Thai
ENG-47
Changing
Setup Menu
† buttons to
Press the …/†
select Player Menu, then
press the √ or ENTER
button.
LANGUAGE SETUP
Player Menu
00708H_P450_XSA/RAD_eng_2
2/27/05
5:10 PM
CHANGING SETUP
Page 48
MENU
Using the Disc Menu Language
This function changes the text language only on the disc menu screens.
1
With the unit in Stop
mode, press the MENU
button.
2
† buttons to
Press the …/†
select Setup, then press
the √ or ENTER button.
Setup
Language Setup
√
Download PDF

advertising