Samsung LT-P468W Quick start guide

Add to my manuals
2 Pages

advertisement

Samsung LT-P468W Quick start guide | Manualzz
BN68-00683C-00Eng_QG
6/4/04
5:30 PM
Page 2
Selecting the Video Signal-Source
Connecting VHF/UHF
You can connect different cable systems to your TV, including cable without a cable box, and cable with a cable
box that descrambles some or all channels.
1
Antennas with 300-ohm Flat Twin Leads
Press the [MENU] button.
The menu will be displayed.
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300-ohm twin flat leads, follow
the directions below.
Channel
2
Press the […/†] buttons to move to
<Channel>, then press the [ENTER]
button.
Air/CATV
: Air
Auto Program
Add/Delete
Fine Tune
LNA
: On
√
√
√
√
√
Move
Return
The <Channel> menu will be displayed.
3
Enter
Press the […/†] buttons to move to
<Air/CATV>, then press the
[ENTER] button.
The signal source menu will be displayed.
Channel
4
Press the […/†] buttons to move to
signal source of your choice, then
press the [ENTER] button.
Press the [EXIT] button to finish.
√
√
√
√
Air/CATV
: AirAir
STD
Auto Program
HRC
Add/Delete
IRC
Fine Tune
LNA
: On
Move
Enter
Note
STD, HRC and IRC identify various types of
cable TV systems.
Contact your local cable
company to identify the
type of cable system that
exists in your particular
area.
At this point the signal
source has been selected. Proceed to “Storing
Channels Automatically”
(next page).
Return
1
Place the wires from the twin leads under the screws on
the 300-75 ohm adaptor (not supplied). Use a screwdriver to
tighten the screws.
2
Plug the adaptor into the VHF/UHF terminal on the bottom of
the back panel.
Antennas with 75-ohm Round Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300-ohm twin flat leads, follow
the directions below.
Storing Channels Automatically
Plug the antenna lead into the VHF/UHF terminal on the bottom of the back panel.
The AUTO PROGRAM feature automatically stores all of the available Air/CATV channels in the memory.
1
2
Press the [AUTO PROG.] button while viewing a TV program.
Press the [MENU] button.
The menu will be displayed.
Press the [ENTER] button, then select <Start> to
commence.
Press the […/†] buttons to move to
<Channel>, then press the [ENTER]
button.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals
before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most
electronics shops).
The <Channel> menu will be displayed.
Channel
3
4
Press the […/†] button to move to
<Auto Program>, then press the
[ENTER] button.
Air/CATV
: Air
Auto Program
Add/Delete
Fine Tune
LNA
: On
√
√
√
√
√
Move
Return
The <Auto Program> menu will be displayed.
Press the [ENTER] button and
select <Start> to begin the Auto
Program function.
Press the [EXIT] button to finish.
Enter
1
Connect both antenna leads to the combiner.
2
Plug the combiner into the VHF/UHF terminal on the bottom
of the rear panel.
Auto Program
Air 13
Start
Enter
Return
BN68-00683C-00
BN68-00683C-00Eng_QG
6/4/04
5:30 PM
Page 4
Connecting Cable TV
You can connect different cable systems to your TV, including cable without a cable box, and cable with a cable
box that descrambles some or all channels.
Cable without a Cable Box
5
Connect another cable between the
other OUT terminal on the splitter and
the A–IN terminal on the RF (A/B)
switch.
Splitter
If you want to connect cable, and you do not need to use a cable box:
6
Plug the incoming cable into the VHF/UHF antenna terminal
on back of the TV.
Connect the last coaxial cable
between the OUT terminal on the RF
(A/B) switch and the VHF/UHF terminal on the rear of the TV.
Splitter
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the
“B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the
cable box’s output channel, which is usually channel 3 or 4.)
Connecting to a Cable Box that Descrambles All Channels
Find the cable that is connected to the ANTENNA OUT terminal on your cable box.
2
Connect the other end of this cable to the VHF/UHF antenna
terminal on the back of the TV.
Plug & Play Feature
When the TV is initially powered On, four basic customer settings proceed automatically and subsequently:
Setting the language, Video signal source, Auto program and Clock.
1
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will
need a two-way splitter, an RF (A/B) switch and four lengths of coaxial cable. (These items are available at most electronics stores.)
1
Press the [POWER] button to turn on the TV.
Plug & Play
2
Press the […/†] buttons to move to language of your choice,
then press the [ENTER] button.
The signal source setup menu will be displayed after a moment.
Find and disconnect the cable that is connected to the ANTENNA IN terminal on your cable box.
This terminal might be labeled “ANT IN”, “VHF IN” or simply, “IN”.
3
English
Français
Español
Português
Move
Enter
Skip
Press the […/†] buttons to move to signal source of your
choice: <Air, STD, HRD and IRC>, then press the [ENTER]
button.
Air/CATV
Air
STD
HRC
IRC
Move
Enter
Skip
Auto Program
Connect this cable to a two-way splitter.
Incoming Cable
Connect a coaxial cable between an
OUTPUT terminal on the splitter and
the IN terminal on the cable box.
Connect a coaxial cable between the
ANTENNA OUT terminal on the cable
box and the B–IN terminal on the
RF(A/B) switch.
Air 13
Press the [ENTER] button then select <START>.
4
The TV will begin memorizing all of the available channels.
To stop, press the [ENTER] button again.
In a moment the <Clock Set> menu will be displayed.
Start
Enter
Skip
Clock Set
Incoming Cable
Hour
Splitter
Cable Box
4
Language
Plug & Play
Splitter
3
Plug & Play
The message <Plug & Play> is displayed.
In a moment the Language menu will be displayed.
The <Auto Program> menu will be displayed after a moment.
2
TV
RF(A/B)
Switch
Cable Box
1
RF(A/B)
Switch
Cable Box
5
12
Cable Box
RF(A/B)
Switch
6
am/pm
00
am
Press the […/†/œ/√] buttons to set the current time.
Move
Splitter
Minute
Press the [MENU] button to finish.
Adjust
Enjoy your watching
Skip

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement