Samsung | HW-MS6500 | Samsung 回音壁条形音响 HW-MS6500 Quick start guide

USER MANUAL
HW-MS6500
SAFETY INFORMATION
SAFETY WARNINGS
•• To prevent injury, this apparatus must be
securely attached to the floor/wall in
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
accordance with the installation instructions.
NOT REMOVE THE COVER (OR BACK).
•• This product contains chemicals known to the
NO USER-SERVICEABLE PARTS ARE INSIDE.
State of California to cause cancer and birth
REFER SERVICING TO QUALIFIED SERVICE
defects or other reproductive harm.
PERSONNEL.
CAUTION
CAUTION
•• Do not expose this apparatus to dripping or
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
splashing. Do not put objects filled with
liquids, such as vases, on the apparatus.
This symbol indicates that high voltage
is present inside. It is dangerous to make
any kind of contact with any internal
part of this product.
This symbol indicates that this product
comes with important literature
concerning operation and maintenance.
•• To turn this apparatus off completely, you
must pull the power plug out of the wall
socket. Consequently, the power plug must
be easily and readily accessible at all times.
FCC NOTE (for U.S.A):
Class B FCC Statement
The included module(s) has been tested and
Class II product : This symbol indicates
that a safety connection to electrical
earth (ground) is not required.
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
AC voltage : Rated voltage marked with
this symbol is AC voltage.
reasonable protection against harmful
interference in a residential installation. This
DC voltage : Rated voltage marked with
this symbol is DC voltage.
equipment generates, uses and can radiate radio
Caution. Consult Instructions for use :
This symbol instructs the user to consult
the user manual for further safety
related information.
frequency energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
WARNING
•• To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one of the following measures:
ENG - ii
Important Safety Instructions
•• Reorienting or relocating the receiving
antenna.
Read these operating instructions carefully
•• Increasing the separation between the
before using the unit. Follow all the safety
equipment and receiver.
•• Connecting the equipment to an outlet that is
on a different circuit than the radio or TV.
instructions listed below. Keep these operating
instructions handy for future reference.
1. Read these instructions.
•• Consulting the dealer or an experienced
2. Keep these Instructions.
radio/TV technician for help.
3. Heed all warnings.
4. Follow all instructions.
FCC Radiation Exposure Statement :
5. Do not use this apparatus near water.
This equipment complies with FCC radiation
6. Clean only with dry cloth.
exposure limits set forth for an uncontrolled
7. Do not block any ventilation openings.
environment.
Install in accordance with the manufacturer’s
This equipment should be installed and operated
so there is at least 8 inches (20 cm) between the
radiator and your body. This device and its
instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
antenna(s) must not be co-located or operated in
apparatus (including amplifiers) that produce
conjunction with any other antenna or
heat.
transmitter.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug.
FCC Caution :
A polarized plug has two blades with one
•• Any changes or modifications not expressly
wider than the other. A grounding type plug
approved by the party responsible for
has two blades and a third grounding prong.
compliance could void the user’s authority to
The wide blade or the third prong are
operate this equipment. This device complies
provided for your safety. If the provided plug
with Part 15 of the FCC Rules. Operation is
does not fit into your outlet, consult an
subject to the following two conditions: (1)
electrician for replacement of the obsolete
This device may not cause harmful
interference, and (2) this device must accept
any interference received, including
outlet.
10.Protect the power cord from being walked
on or pinched particularly at plugs,
interference that may cause undesired
convenience receptacles, and the point
operation.
•• This product satisfies FCC regulations when
shielded cables and connectors are used to
where they exit from the apparatus.
11.Only use attachments/accessories specified
by the manufacturer.
connect the unit to other equipment. To
prevent electromagnetic interference with
electric appliances, such as radios and
televisions, use shielded cables and
connectors for connections.
ENG - iii
12.Use only with the cart, stand,
2. During thunderstorms, disconnect the AC
tripod, bracket, or table
plug from the wall outlet. Voltage peaks due
specified by the manufacturer,
to lightning could damage the unit.
or sold with the apparatus.
3. Do not expose the unit to direct sunlight or
When a cart is used, use caution when
other heat sources. This could lead to
moving the cart/apparatus combination to
overheating and cause the unit to
avoid injury from tip-over.
malfunction.
13.Unplug this apparatus during lightning
4. Protect the product from moisture (i.e.
storms or when unused for long periods of
vases), and excess heat (e.g. a fireplace) or
time.
equipment creating strong magnetic or
14.Refer all servicing to qualified service
electric fields. Unplug the power cable from
personnel. Servicing is required when the
the AC wall socket if the unit malfunctions.
apparatus has been damaged in any way,
Your product is not intended for industrial
such as power-supply cord or plug is
use. It is for personal use only. Condensation
damaged, liquid has been spilled or objects
may occur if your product has been stored in
have fallen into the apparatus, the apparatus
cold temperatures. If transporting the unit
has been exposed to rain or moisture, does
during the winter, wait approximately
not operate normally, or has been dropped.
2 hours until the unit has reached room
temperature before using.
5. The battery used with this product contains
PRECAUTIONS
chemicals that are harmful to the
environment. Do not dispose of the battery
in the general household trash. Do not
1. Ensure that the AC power supply in your
expose the battery to excess heat, direct
house complies with the power
sunlight, or fire. Do not short circuit,
requirements listed on the identification
sticker located on the back of your product.
Install your product horizontally, on a
suitable base (furniture), with enough space
around it for ventilation (3~4 inches). Make
sure the ventilation slots are not covered. Do
not place the unit on amplifiers or other
equipment which may become hot. This unit
is designed for continuous use. To fully turn
off the unit, disconnect the AC plug from the
wall outlet. Unplug the unit if you intend to
leave it unused for a long period of time.
ENG - iv
disassemble, or overheat the battery.
Danger of explosion if the battery is replaced
incorrectly. Replace only with the same or
equivalent type.
ABOUT THIS MANUAL
The user manual has two parts: this simple paper USER MANUAL and a detailed FULL MANUAL you can
download.
USER MANUAL
See this manual for safety instructions, product installation,
components, connections, and product specifications.
FULL MANUAL
You can access the Full Manual on Samsung’s on-line customer
support center by scanning the QR code. To see the manual on
your PC or mobile device, download the manual in document
format from the website. (http://www.samsung.com/support)
Design, specifications and App screen are subject to change without prior notice.
ENG - v
CONTENTS
01
Checking the Components
2
Inserting Batteries before using the Remote Control (AA batteries X 2) -------------------------- 2
02
03
Product Overview
3
Front Panel / Right Side Panel of the Soundbar
-------------------------- 3
Bottom Panel of the Soundbar
-------------------------- 3
Connecting the Soundbar
Connecting Electrical Power
04
05
06
4
-------------------------- 4
Connecting to your TV
5
Method 1. Connecting with a Cable
–– Connecting using an Optical Cable
–– Connecting a TV using an HDMI Cable
-------------------------- 5
-------------------------- 5
-------------------------- 6
Method 2. Connecting Wirelessly
–– Connecting a TV via Bluetooth
–– Connecting via Wi-Fi
-------------------------- 7
-------------------------- 7
-------------------------- 8
Connecting an External Device
11
Connecting using an Optical or Analog Audio (AUX) Cable
-------------------------- 11
Connecting using an HDMI Cable
-------------------------- 12
Connecting a Mobile Device
13
Method 1. Connecting via Bluetooth
-------------------------- 13
Method 2. Connecting via Wi-Fi (Wireless Network)
-------------------------- 14
ENG - vi
07
08
3
4
5
7
7
8
09
Using the Remote Control
16
How to Use the Remote Control
-------------------------- 16
Adjusting the Soundbar volume with a TV remote control
-------------------------- 18
Installing the Wall Mount
19
Installation Precautions
-------------------------- 19
Wallmount Components
-------------------------- 19
Assembling the Holder-Cable
-------------------------- 21
Installing the Holder Foot
-------------------------- 22
Software Update
22
10Troubleshooting
23
11License
24
12
Open Source License Notice
24
13
Important Notes About Service
24
14
Specifications and Guide
25
Specifications
-------------------------- 25
3
ENG - vii
01 CHECKING THE COMPONENTS
SMART
MODE
Surround
SOUND
MODE
VOL
BASS
SOUNDBAR
Soundbar Main Unit
Holder-Cable
(AH61-04173A)
Remote Control
/ Batteries
(AH59-02759A)
Holder-Foot (2 EA)
(AH96-04069A)
Power Cord
(3903-001188)
Optical Cable
(AH39-00779A)
Screw
(for Holder-Foot : 2 EA)
(for Holder-Cable : 1 EA)
(6001-001961)
•• For Soundbar wall mounting components, see page 19.
•• See page 21 for instructions on how to use the Holder-Cable.
•• To purchase additional components or optional cables, contact a Samsung Service Center or
Samsung Customer Care.
Inserting Batteries before using the Remote Control (AA batteries X 2)
Slide the battery cover in the direction of the arrow until it is completely removed. Insert 2 AA batteries
(1.5V) oriented so that their polarity is correct. Slide the battery cover back into position.
ENG - 2
02 PRODUCT OVERVIEW
Front Panel / Right Side Panel of the Soundbar
Right Side of the Soundbar
Position the product
Power
Volume
so that the
SAMSUNG logo is
located on the top.
Display
Bottom Panel of the Soundbar
POWER
OUT
(For TV)
POWER
IN
DIGITAL AUDIO IN
(OPTICAL)
WIRELESS
AUX IN
HDMI IN
HDMI OUT
(TV-ARC)
Wi-Fi SETUP SPK ADD
POWER
OUT
(For TV)
POWER
IN
Source
Selects the source input mode. (D.IN / AUX / HDMI / WIFI / BT)
•• To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and
POWER OUT
(For TV)
Connect the power cord of a Samsung TV connected to the Soundbar and mounted on
the wall using a Wall Mount Kit (WMN300SB - not supplied).
POWER IN
D.IN
WIRELESS
AUX
hold the
(Source) button for more than 5 seconds.
Connect the Soundbar's AC power cable.
Connect to the digital (optical) output of an external device.
Attach the wireless dongle that connects the Soundbar to surround speakers and a
subwoofer wirelessly. (The surround speaker, subwoofer, and wireless dongle are sold
separately.)
Connect to the Analog output of an external device.
ENG - 3
HDMI IN
HDMI OUT
Wi-Fi SETUP
/ SPK ADD
Inputs digital video and audio signals simultaneously using an HDMI cable.
Connect to the HDMI output of an external device.
Connect to the HDMI (ARC) jack on a TV.
Connect to a wireless network (Wi-Fi) via the Samsung Multiroom app.
03 CONNECTING THE SOUNDBAR
Connecting Electrical Power
•• For more information about the required electrical power and power consumption, refer to the
label attached to the product. (Label : Bottom of the Soundbar Main Unit)
•• Connect the supplied power cable to the
Power Cord
POWER IN jack.
POWER
IN
POWER
OUT
(For TV)
Connecting
Electrical Power
POWER
IN
Bottom of the
Soundbar Main Unit
POWER
OUT
(For TV)
POWER
OUT
(For TV)
POWER
IN
•• The POWER OUT jack is used to provide power to a
Samsung TV mounted on the wall using a Wall Mount
Kit (WMN300SB - not supplied).
•• The POWER OUT jack can connect only to Samsung
TVs that use a 2-pin power cord and consume 400 W
or less. (Connecting the jack to a device that consumes
more than 400 W may damage the Soundbar or cause
a malfunction.)
POWER
IN
Bottom of the Soundbar Main Unit
For a list of Samsung TVs that are compatible with the
WMN300SB Wall Mount Kit and the POWER OUT jack,
see the WMN300SB Wall Mount Kit user manual.
You can view the manual on line at
http://www.samsung.com/support.
ENG - 4
04 CONNECTING TO YOUR TV
Hear TV sound from your Soundbar through wired or wireless connections.
•• When the Soundbar is connected to a selected Samsung TVs, the Soundbar can be controlled using
the TV’s remote control.
–– When using optical cable, this feature can be supported by 2017 Samsung Smart TVs that
support Bluetooth.
–– This function also allows you to use the TV menu to adjust the sound field and various settings
as well as the volume and mute.
Method 1. Connecting with a Cable
Connecting using an Optical Cable
Bottom of the Soundbar
DIGITAL AUDIO IN
(OPTICAL)
OPTICAL OUT
Optical Cable
WIRELESS
AUX IN
D.IN
Right Side of the Soundbar
1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV
with a digital optical cable.
2. Press the
(Source) button on the right side panel or remote control, and then select the
“D.IN” mode.
Auto Power Link
Auto Power Link automatically turns on the Soundbar when the TV is turned on.
1. Connect the Soundbar and a TV with a digital optical cable.
2. Press the
(Source) button on the right side panel or on the remote control, and then select
“D.IN”.
ENG - 5
3. Press the Left button on the remote control for 5 seconds to turn Auto Power
Link on or off.
•• Auto Power Link is set to ON by default.
(To turn off this function, turn off Auto Power using the Soundbar.)
•• Depending on the connected device, Auto Power Link may not function.
•• This function is only available in the “D.IN” mode.
Connecting a TV using an HDMI Cable
Bottom of the Soundbar
Connect to the HDMI IN
(ARC) port of your TV.
HDMI IN
HDMI IN
(ARC)
HDMI Cable
HDMI OUT
(not supplied)
(TV-ARC)
Connect to the HDMI OUT (TV-ARC)
port of the Soundbar main unit.
TV
ARC
Right Side of the
Soundbar
1. With the Soundbar and TV turned on, connect the HDMI cable (not supplied) as shown in the figure.
2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV
sound.
•• If TV sound is inaudible, press the
(Source) button on the remote control or on the right side
of the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence,
and TV sound is played.
•• If “TV ARC” does not appear in the display window of the Soundbar main unit, confirm that the
cable is connected to the correct port.
•• Use the volume buttons on the TV’s remote control to change the volume of the Soundbar.
ENG - 6
Method 2. Connecting Wirelessly
Connecting a TV via Bluetooth
When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
•• Only one TV can be connected at a time.
The initial connection
1. Press the
(Source) button on the right side panel or on the remote control, and then select
“BT”.
2. Change “BT” to “BT PAIRING”.
•• If “BT READY” appears, press and hold the
(Source) button on the right side panel of the
Soundbar or on the remote control for more than 5 seconds to display “BT PAIRING”.
3. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)
4. Select “[AV] Samsung Soundbar MSxxxx” from the list on TV’s screen.
An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV Bluetooth device list.
To connect to the Soundbar, select the message and establish a connection.
•• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.
5. You can now hear TV sound from the Soundbar.
If the device fails to connect
•• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar MSxxxx”) appears in
the list, delete it.
•• In “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side
panel of the Soundbar or on the remote control to switch to “BT PAIRING” mode.
Then, select “[AV] Samsung Soundbar MSxxxx” from the TV’s search list.
What are the BT READY and BT PAIRING statuses?
•• BT READY : In this mode, you can search for previously connected TVs or connect to the Soundbar
from a previously connected mobile device.
•• BT PAIRING : In this mode, you can connect to a new device. (While in “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side of the Soundbar or on the remote
control.)
ENG - 7
S
NOTES
•• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
•• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 32.8 ft.
•• The Soundbar automatically turns off after 5 minutes in the Ready state.
•• The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:
–– If there is a strong electrical field around the Soundbar.
–– If several Bluetooth devices are simultaneously paired with the Soundbar.
–– If the Bluetooth device is turned off, not in place, or malfunctions.
•• Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
Disconnecting the Soundbar from the TV
Press the
(Source) button on the right side panel or on the remote control and switch to any mode
but “BT”.
•• Disconnecting takes time because the TV must receive a response from the Soundbar.
(The time required may differ, depending on the TV model.)
•• To cancel automatic Bluetooth connection between the Soundbar and TV, press the
p (Play/Pause) button on the remote control for 5 seconds in “BT READY” status. (Toggle On → Off)
Connecting via Wi-Fi
Pre-connection Checklist
1. Confirm that your Samsung smart TV was released after 2014. This function is compatible only
with Samsung smart TVs released after 2014.
2. Make sure your Wireless router (Wi-Fi) is ready and working.
S
3. Make sure that the TV is connected to the Wireless router (your Wi-Fi network).
F
F
ENG - 8
Step 1 : Connecting the Soundbar to Wi-Fi
1. Press the
(Source) button on the right side of the Soundbar or on the remote control to select
“WIFI” mode.
•• When using selected Samsung TV (2016 or 2017 Samsung smart TVs that support Bluetooth.)
–– If you select “WIFI” mode when the TV is turned on, the TV screen displays a pop-up
window providing instructions on how to automatically connect the Soundbar to a wireless
router (Wi-Fi). Refer to instructions in the pop-up window of TV.
WIFI
2. Connect your mobile device (smartphone, tablet etc.) to the Wi-Fi network the TV is connected to.
3. Install and launch the Samsung Multiroom app on your mobile device (smartphone, tablet etc.).
Samsung Multiroom app
Android
iOS
4. Follow the instructions in the app screen on the mobile device to connect the Soundbar to your
Wi-Fi network.
Step 2 : Configuring Settings on the TV
•• If the TV disconnects from your wireless network after you change the input source to the
Soundbar, use the TV menu to connect the TV to the network again.
For TVs released in 2017
1. Home menu  Settings (
)  Sound  Sound Output  Select [AV] Soundbar MSxxxx (Wi-Fi)
2. The Soundbar outputs TV sound.
For TVs released in 2016
1. Home menu  Settings (
)  Sound  Sound Output  Select [AV] Samsung Soundbar MSxxxx
(Wi-Fi)
2. The Soundbar outputs TV sound.
ENG - 9
For TVs released in 2015
1. Home menu  Sound  Speaker List  Select [AV] Samsung Soundbar MSxxxx (Wi-Fi)
2. The Soundbar outputs TV sound.
For TVs released in 2014
1. Home menu  Sound  Speaker Settings  Select Multiroom Link - Settings 
Soundbar+Surround.
2. From the Soundbar menu item, select “[AV] Samsung Soundbar MSxxxx” and then select “OK”.
3. Home menu  Sound  Speaker Settings  Select TV Sound Output  Multiroom Link
Speaker Settings
Multiroom Link
TV Sound Output
Multiroom Link
TV Speaker
• TV Installation Type
TV SoundConnect
• Samsung Audio Device List
• Add New Device
Multiroom Link
• Settings
Soundbar+Surround
3
Stand
Soundbar
On
Soundbar+Surround
Bluetooth Headphone
• Bluetooth Headphone List
OK
[AV] Samsung Soundbar MSxxxx[AV] Samsung Soundbar MSxxxx
c
1
2
Don’t Use
OK
Volume Level
Speaker Test
Edit Na
4. The Soundbar outputs TV sound.
NOTES
•• The TV and Soundbar must be connected to the same wireless network (Wi-Fi).
•• If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi
connection between the TV and Soundbar. Contact your Internet service provider for details.
•• If the 5GHz Wi-Fi connection is not smooth, use the 2.4GHz bandwidth.
ENG - 10
05 CONNECTING AN EXTERNAL DEVICE
Connect to an external device via a wired or wireless network to play the external device’s sound
through the Soundbar.
Connecting using an Optical or Analog Audio (AUX) Cable
Right Side of the Soundbar
BD / DVD player / Set-top box /
Game console
DIGITAL AUDIO IN
(OPTICAL)
2
OPTICAL OUT
Optical Cable
WIRELESS
OR
AUX IN
R - AUDIO - L
Audio (AUX) Cable
(not supplied)
Bottom of the Soundbar
Optical Cable
XX Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source
Device using a digital optical cable.
YY Select “D.IN” mode by pressing the
(Source) button on the right side panel or on the remote
control.
OR
Audio (AUX) Cable
XX Connect AUX IN (Audio) on the main unit to the AUDIO OUT jack of the Source Device using an audio
cable.
YY Select “AUX” mode by pressing
(Source) button on the right side panel or on the remote control.
ENG - 11
Connecting using an HDMI Cable
Bottom of the Soundbar
External Device
HDMI IN
HDMI OUT
HDMI Cable
(not supplied)
HDMI OUT
(TV-ARC)
HDMI IN
(ARC)
HDMI Cable
(not supplied)
HDMI
Right Side of the
Soundbar
1. Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the
HDMI OUT jack on your digital device.
2. Connect an HDMI cable (not supplied) from the HDMI OUT (TV-ARC) jack on the back of the
product to the HDMI IN jack on your TV.
3. Press the
(Source) button on the right side panel or on the remote control, and then select
“HDMI”.
4. “HDMI” mode is displayed on the Soundbar display panel and sound plays.
ENG - 12
06 CONNECTING A MOBILE DEVICE
Method 1. Connecting via Bluetooth
When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of
cabling.
•• You cannot connect more than one Bluetooth device at a time.
Bluetooth device
The initial connection
1. Press the
(Source) button on the right side panel or on the remote control, and then select
“BT”.
2. Change “BT” to “BT PAIRING”.
•• If “BT READY” appears, press and hold the
(Source) button on the right side panel of the
Soundbar or on the remote control for more than 5 seconds to display “BT PAIRING”.
3. Select “[AV] Samsung Soundbar MSxxxx” from the list.
•• When a Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT”
appears in the front display.
4. Play music files from the device, connected via Bluetooth, through the Soundbar.
If the device fails to connect
•• If the previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar MSxxxx”) appears in
the list, delete it.
•• In “BT” mode, press and hold the
(Source) button for more than 5 seconds on the right side
panel of the Soundbar or on the remote control to switch to “BT PAIRING” mode.
Then, select “[AV] Samsung Soundbar MSxxxx” from the Bluetooth device search list.
For more information about Bluetooth connections, refer to “Connecting a TV via
Bluetooth” on pages 7 ~ 8.
ENG - 13
Method 2. Connecting via Wi-Fi (Wireless Network)
•• Connect a single Soundbar to Wi-Fi to access a variety of music streaming services and Internet
radio. Connect multiple Soundbars to Wi-Fi to use grouped playback or stereo sound mode.
•• To connect a Soundbar to a mobile device via a wireless network (Wi-Fi), the Samsung Multiroom
app is required.
Mobile device
The initial connection
1. Press the
(Source) button on the right side of the Soundbar or on the remote control to select
“WIFI” mode.
WIFI
2. Install and launch the Samsung Multiroom app on your mobile device (e.g. smartphone or tablet).
Samsung Multiroom app
Android
iOS
3. Follow the instructions in the app screen on the mobile device to connect the Soundbar to Wi-Fi.
ENG - 14
Installing an additional Soundbar when Samsung wireless speakers are already in use
1. On the Home screen of the Samsung Multiroom app, select Settings (
) at the top, and then
select “Add Speaker”
2. To connect the Soundbar to 2 Samsung wireless speakers and configure a surround sound system,
follow the steps shown below. (You cannot set up a surround sound system using one audio device
and one Soundbar.)
XX Touch to go to the list of all speakers.
YY Touch on the right of the Soundbar model name.
ZZ Touch Surround Setup. Select Done after dragging the speaker to the desired location.
[[ The Surround connection is complete.
Soundbar
NOTE
•• To connect an additional SWA-9000S (not supplied), disconnect the Samsung wireless speakers
from the Soundbar to disable the surround sound system. (If connecting the surround speakers
without disconnecting SWA-9000S, sound is played via both the Samsung wireless speaker and the
Surround speaker.)
ENG - 15
07 USING THE REMOTE CONTROL
How to Use the Remote Control
Turns the Soundbar on and off.
Power
You can select from TREBLE, SYNC,
REAR LEVEL, or REAR SPEAKER ON/OFF.
Sound Control
Control TREBLE, and then use the
••
SMART
MODE
Surround
SOUND
MODE
••
VOL
BASS
Surround
Surround
SOUNDBAR
SOUND
••
MODE
SOUND
MODE
Surround
SOUND
MODE
SOUND
MODE
You can select the desired sound effect
VOL by choosing
BASSSTANDARD, MUSIC, CLEAR VOICE,
SPORTS, or MOVIE.
VOL
BASS
SOUND MODE
VOL
VOL
Up/Down buttons to adjust the volume
within the -6 to +6 range.
If the video and audio between the TV and
your Soundbar are not synchronized, select
SYNC in Sound Control, and then set audio
delay between 0~300 milliseconds by
using the Up/Down buttons.
If surround speakers (not supplied) are
connected, select REAR LEVEL and use the
Up/Down
buttons to adjust the volume
SMART
MODE
SMART
within
the -6 to +6 range.
MODE
The REAR SPEAKER function can be turned
ON/OFF by using the Up/Down buttons.
Audio Sync is only supported in some
functions.
VO
The Surround Sound function adds depth and a sense of space to sound.
SMART
Each time
MODEyou press this button, ON and OFF alternate.
SMART
•• ON : Play sound over all the speakers.
MODE
•• OFF : You can hear the sound of the original source channel from several speakers.
Surround
Surround
Surround
•• To adjust the TREBLE volume, select Sound
Surround
•• DRC (Dynamic Range Control)
Lets you apply dynamic range control to Dolby Digital tracks. If you press and hold the
SOUND MODE button while in standby mode, DRC (Dynamic Range Control) turns on
or off. With the DRC turned on, loud sound is reduced. (The sound may be distorted.)
BASS
BASS
VOL
ENG - 16
Press to select a source connected to the Soundbar.
•• BT PAIRING mode
To turn on “BT PAIRING” mode in “BT” mode, press and hold the
for more than 5 seconds. See page 13 for details.
Source
(Source) button
Press the p button to pause a music file temporarily.
If you press the button again, the music file plays.
Play / Pause
(BT/Wi-Fi)
SMART
MODE
Surround
Press the indicated areas to select Up/Down/Left/Right.
SMART
SOUND
MODE
MODE
Surround
Up/Down/
SMART
MODE
Surround
SOUND
MODE
Left/Right
SOUND
MODE
Press Up/Down/Left/Right on the button to select or set functions.
•• Repeat
To use the repeat function, press the Up button.
VOL
BASS
VOL
VOL
BASS
BASS
•• Music Skip
Press the Right button to select the next music file. Press the Left button to select
the previous music file.
•• Anynet+ / Auto Power Link
You can turn Anynet+ and Auto Power Link on or off.
Anynet+ and Auto Power Link are controlled by the Right and Left buttons
respectively.
–– Anynet+ : If the Soundbar is connected to a Samsung TV through an HDMI cable,
you can control your Soundbar with the Samsung TV’s remote control.
Press and hold the Right button for 5 seconds to toggle Anynet+ ON and OFF.
–– Auto Power Link : If the Soundbar is connected to your TV through a digital
optical cable, the Soundbar can automatically turn on when you turn on your TV.
Press and hold the Left button for 5 seconds to toggle Auto Power Link ON and
OFF.
–– Anynet+ / Auto Power Link are set to ON by default.
Surround
SMART
MODE
Automatically optimizes sound effects to suit the scene currently playing.
The mode turns on or off each time the button is pressed.
SMART MODE
SOUND
MODE
VOL
BASS
ENG - 17
SO
SO
M UN
OD D
E
BA
SS
BA
SS
D
N
U
SO
VO
L
BA
R
BA
R
SO
U
N
VO
L
D
BA
R
D
N
SO
U
VO
L
Su
rro
un
d
SM
M AR
OD T
E
SM
M AR
OD T
E
SO
M UN
OD D
E
Su
rro
un
d
SO
M UN
OD D
E
BA
SS
BA
SS
D
N
U
SO
VO
L
BA
R
Su
rro
un
d
SM
M AR
OD T
E
SM
M AR
OD T
E
SO
M UN
OD D
E
BASS
Su
rro
un
d
VOL
U
N
VO
L
Push the button up or down to adjust the BASS volume within the -6 to +6 range.
To set the BASS volume level to 0, press the button.
•• When a Subwoofer (not supplied) is connected, the BASS button switches to the
Subwoofer Key. Push the button up or down to adjust the subwoofer volume either to -12
or within the -6 to +6 range. To set the subwoofer volume level to 0, press the button.
VOL
D
BA
R
BA
SS
Su
rro
un
d
BA
SS
D
BA
R
SO
U
N
VO
L
SO
SOUND
MODE
SO
M UN
OD D
E
SM
M AR
OD T
E
SM
M AR
OD T
E
Su
rro
un
d
BA
SS
D
BA
R
SMART
MODE
U
N
VO
L
D
BA
R
U
N
SO
M UN
OD D
E
SM
M AR
OD T
E
BASS
BASS
Surround
SO
VO
L
BA
SS
Su
rro
un
d
VOL
SO
M UN
OD D
E
SM
M AR
OD T
E
SO
M UN
OD D
E
Su
rro
un
d
SOUND
MODE
Push the button up or down to adjust the volume.
•• Mute
Press the VOL button to mute the sound. Press it again to unmute the sound.
Adjusting the Soundbar volume with a TV remote control
Use the TV menu to set the TV speaker on a Samsung TV to external speakers.
(For more information, see the TV’s user manual.)
•• After installing the Soundbar, you can adjust the Soundbar’s volume using the IR remote control
that came with a Samsung TV. (If you do not want to use this function, when the Soundbar is on,
press and hold the Surround button for 5 seconds. “OFF-TV REMOTE” appears in the Soundbar’s
display and the function turns off.) To adjust the volume using only the Samsung TV remote control,
press and hold the Surround button for more than 5 seconds until “SAMSUNG-TV REMOTE”
appears in the Soundbar display.
–– Each time the Surround button is held for 5 seconds, the mode switches in the following order:
“SAMSUNG-TV REMOTE” (Default mode) → “OFF-TV REMOTE” → “ALL-TV REMOTE”.
•• To adjust the Soundbar volume with the remote control that came with a TV made by a third party
manufacturer, turn the Soundbar on, press and hold the Surround button for 5 seconds
(“OFF-TV REMOTE” appears on the Soundbar’s display), release the Surround button, and then
press and hold the Surround button again for more than 5 seconds. (“ALL-TV REMOTE” appears on
the Soundbar’s display.)
–– This function may not be available, depending on the remote control.
–– For manufacturers that support this feature, refer to the FULL MANUAL
for your Soundbar on the Samsung web site (www.samsung.com/support).
–– This volume control function works with IR TV remotes only. It does not work with Bluetooth
TV remotes (remotes that require pairing).
ENG - 18
BA
R
D
08 INSTALLING THE
WALL MOUNT
Wallmount Components
450mm
Installation Precautions
Wall Mount Guide (AH63-04369B)
•• Install on a vertical wall only.
•• Do not install in a place with high
temperature or humidity.
•• Verify whether the wall is strong enough to
support the product’s weight. If not, reinforce
Holder-Screw (2 EA)
Screw (2 EA)
(AH61-04110A)
(6001-001202)
the wall or choose another installation point.
•• Purchase and use the fixing screws or
anchors appropriate for the kind of wall you
have (plaster board, iron board, wood, etc.).
If possible, fix the support screws into wall
Bracket-Wall Mount (2 EA)
studs.
(AH61-04119A)
•• Purchase wall mounting screws according to
the type and thickness of the wall you want to
mount the Soundbar on.
1. Place the Wall Mount Guide against the wall
–– Diameter: M5
surface.
–– Length: 1 3/8 inches or longer
•• The Wall Mount Guide must be level.
recommended.
•• If your TV is mounted on the wall, install
•• Connect cables from the unit to external
the Soundbar at least 2 inches (5 cm)
devices before you install the Soundbar on
below the TV.
the wall.
•• Make sure the unit is turned off and
unplugged before you install it. Otherwise, it
may cause an electric shock.
2 inches or more
ENG - 19
2. Align the Paper Template’s Center Line with
5. Push a screw (not supplied) through each
the center of your TV (if you are mounting
Holder-Screw, and then screw each screw
the Soundbar below your TV), and then fix
firmly into a support screw hole.
the Wall Mount Guide to the wall using tape.
•• If you are not mounting below a TV, place
the Center Line in the center of the
installation area.
6. Install the 2 Bracket-Wall Mounts in the
correct orientation on the bottom of the
450mm
Soundbar, using 2 Screws.
Center Line
3. Use a sharp object, such as a pen or pencil, to
mark the holes’ positions, and then remove
the Wall mount Guide.
450mm
CENTER LINE
•• When assembling, make sure the hanger
part of the Bracket-Wall Mounts are
located behind the rear of the Soundbar.
4. Using an appropriately sized drill bit, drill a
hole in the wall at each marking.
Rear of Soundbar
•• If the markings do not correspond to the
positions of studs, make sure you insert
appropriate anchors or mollies into the
holes before you insert the support
screws. If you use anchors or mollies,
make sure the holes you drill are large
enough for the anchors or mollies you
use.
Right end of Soundbar
ENG - 20
Assembling the Holder-Cable
7. Install the Soundbar with the attached
Bracket-Wall Mounts by hanging the
Bracket-Wall Mounts on the Holder-Screws
on the wall.
As shown in the image, use the supplied Screw to
fix the Holder-Cable to the Soundbar, and then
use the Holder-Cable to organize any cables.
HDMI
IN
OUT
HDMI C)
(TV-AR
L AUDIO
DIGITA AL)
(OPTIC
8. Slide the Soundbar down as shown below so
IN
LESS
WIRE
R
POWET
OU
(For TV)
that the Bracket-Wall Mounts rest securely
AUX IN
R
POWE
IN
on the Holder-Screws.
•• Insert the Holder-Screws into the wide
Holder-Cable
(bottom) part of the Bracket-Wall
Mounts, and then slide the Bracket-Wall
Mounts down so that Bracket-Wall
Mounts rest securely on the Holder-
OUT
HDMI C)
(TV-AR
Screws.
DIO IN
L AU
DIGITA AL)
(OPTIC
LESS
WIRE
R
POWET
OU )
(For TV
AUX IN
R
POWE
IN
Wi-Fi SETUP
HDMI
IN
OUT
HDMI
(TV-ARC)
AUDIO
DIGITAL )
(OPTICAL
S
WIRELES
POWER
OUT
(For TV)
AUX IN
POWER
IN
ENG - 21
IN
SPK ADD
Installing the Holder Foot
If you are not mounting the Soundbar on the wall,
use the 2 provided screws to attach the 2 Holder
09 SOFTWARE
UPDATE
Feet to the bottom of the Soundbar as shown
below.
When the Soundbar is connected to the Internet,
•• Note that the stands of certain Samsung TVs
are designed to provide a fixed place for the
Soundbar. To finalize the installation of the
software updates automatically occur even when
the Soundbar is turned off.
•• To use the Auto Update function, the
Soundbar, you place the Holder Feet of the
Soundbar must be connected to the Internet.
Soundbar on the legs of the stand.
The Wi-Fi connection to the Soundbar will be
terminated if its power cord is disconnected
or the power is cut off. If the power is cut off,
turn on the Soundbar and reconnect it.
ADD
P SPK
Wi-Fi SETU
Wi-Fi SETUP
HDMI
SPK ADD
IN
OUT
HDMI
(TV-ARC)
AUDIO
DIGITAL
(OPTICAL)
IN
WIRELESS
POWER
OUT
(For TV)
AUX IN
POWER
IN
Place Soundbar
ENG - 22
10 TROUBLESHOOTING
Refer to the table below if this product does not function properly. If the problem you are experiencing
is not listed below or if the instructions below do not help, turn off the product, disconnect the power
cord, and contact Samsung Electronics at 1-800-SAMSUNG (1-800-726-7864).
The unit will not turn on.
Cannot connect to the TV.
Is the power cord plugged into the outlet?
If connected via a wired network
;; Connect the power plug to the outlet.
;; Check if the cable is connected correctly.
(Check the port name to make sure that
A function does not work when the button
is pressed.
the cable is connected to the correct port.)
(See the corresponding page regarding
each connection method.)
Is there static electricity in the air?
;; Press the
;; Disconnect the power plug and connect it
(Source) button on the right
side of the Soundbar or on the remote
again.
control to check if the mode is correct.
Sound dropouts occur in BT mode.
If connected via a wireless network
;; Connected via Bluetooth
;; See the Bluetooth connection sections on
1. Switch the Soundbar to “BT PAIRING”
pages 7 and 13.
mode, and then use the TV to search
Sound is not produced.
again. (See page 7 for details.)
;; Connected via Wi-Fi
Is the Mute function on?
1. Check if the TV is a compatible model.
;; Press the VOL button to cancel the
•• Only Samsung smart TVs released
function.
after 2014 are supported.
Is the volume set to minimum?
2. Check if the TV is connected to Wi-Fi.
;; Adjust the Volume.
•• If the TV is not connected to Wi-Fi, use
The remote control does not work.
the network menu on the TV to
establish a connection. (See the TV
Are the batteries drained?
user manual.)
;; Replace with new batteries.
Is the distance between the remote control and
Soundbar main unit too far?
3. Check if the Soundbar is connected to
Wi-Fi.
•• When connected, the Soundbar is
;; Move the remote control closer to the
found in the list of speakers when
Soundbar main unit.
Samsung Multiroom app is run on the
mobile device (e.g. smartphone or
tablet). (See page 14 for details.)
ENG - 23
4. Check for a DFS channel.
•• If your wireless router (Wi-Fi) is using a
DFS channel, you cannot establish a
Wi-Fi connection between the TV and
Soundbar. Contact your Internet
service provider for details.
12 OPEN SOURCE
LICENSE NOTICE
For further information on Open Sources used in
this product, please visit the website:
11 LICENSE
http://opensource.samsung.com
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio, Pro Logic,
and the double-D symbol are trademarks of Dolby
Laboratories.
13 IMPORTANT
NOTES ABOUT
SERVICE
•• Figures and illustrations in this User Manual
are provided for reference only and may differ
from actual product appearance.
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS
Licensing Limited. DTS, the Symbol, DTS in
combination with the Symbol, and DTS Digital
Surround are registered trademarks or
trademarks of DTS, Inc. in the United States
and/or other countries. © DTS, Inc. All Rights
Reserved.
•• An administration fee may be charged if
either:
a. An engineer is called out to your home at
your request and there is no defect in the
product.
b. You bring the unit to a repair center and
there is no defect in the product.
•• You will be advised of the amount of the
administration fee before any work is done or
a home visit is made.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
•• If you have a problem with this product, we
strongly recommend you read the appropriate
section of this manual, visit the Support page
for your product at www.samsung.com, or call
Samsung Product Support (1-800-726-7864)
to find an answer before you contact a service
•• The Spotify Software is subject to third party
licenses found here :
www.spotify.com/connect/third-partylicenses.
•• For more information about Spotify Connect,
please visit www.spotify.com/connect
ENG - 24
center for a repair.
14 SPECIFICATIONS AND GUIDE
Specifications
GENERAL
Weight
14.3 lbs (6.5 kg)
Dimensions
(W x H x D)
45.7 x 3.1 x 6.6 inches
Operating Temperature Range
+41°F to +95°F (+5°C to +35°C)
Operating Humidity Range
10 % ~ 75 %
(1160.0 x 80.0 x 168.0 mm)
1080p, 1080i, 720p, 576p, 480p
HDMI
Video
2160p@24/25/30Hz 4:4:4
2160p@60/50Hz 4:2:0
Speaker
Woofer x 6, Tweeter x 3, 4ohm
LPCM 2ch, Dolby Audio™ (supporting
Supported play formats
Dolby® Digital), DTS
NOTES
•• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
•• Weight and dimensions are approximate.
•• For more information about the power supply and power consumption, refer to the label attached
to the product. (Label : Bottom of the Soundbar Main Unit)
•• Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call
(877) 278 - 0799
Precaution : The product will restart automatically if you turn on/off Wi-Fi/Ethernet.
Wi-Fi/Ethernet
Port deactivation method
Press Wi-Fi SETUP button on the product for
30 seconds to turn Wi-Fi/Ethernet On / Off.
Bluetooth
Port deactivation method
Press SPK ADD button on the product for
30 seconds to turn Bluetooth On / Off.
ENG - 25
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG and delivered new, in the original carton to the original
consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited
warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the
United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and
service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original
dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service
center. Transportation of the product to and from the service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or
reconditioned parts or products if found to be defective during the limited warranty period specified above.
All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG.
Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer.
SAMSUNG’s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand
name are set forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products,
if provided, are on an “AS IS” basis.
Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and
except to the extent otherwise expressly provided for in this statement, noncommercial use of this product, and
shall not apply to the following, including, but not limited to: damage which occurs in shipment; delivery and
installation; applications and uses for which this product was not intended; altered product or serial numbers;
cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of
products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs,
external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result in
service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to
follow operating instructions, cleaning, maintenance and environmental instructions that are covered and
prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to
noise, echo, interference or other signal transmission and delivery problems. SAMSUNG does not warrant
uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO
WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY
PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR
CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE
LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS
PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST
SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND
CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND
LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO OTHERS AND
THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG
NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT EXTEND TO
ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR
EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
To obtain warranty service, please contact SAMSUNG customer care center.
The benefits of this Limited Warranty extend only to the original purchaser of Samsung products from an authorized
Samsung reseller. THIS LIMITED WARRANTY SHALL NOT APPLY TO ANY SAMSUNG PRODUCTS PURCHASED
FROM UNAUTHORIZED RESELLERS OR RETAILERS, EXCEPT IN STATES WHERE SUCH RESTRICTION MAY BE
PROHIBITED. For a list of Samsung authorized retailers, please go to:
http://www.samsung.com/us/peaceofmind/authorized_resellers.html.
The party responsible for product compliance:
Samsung Electronics Co., LTD.
America QA lab of Samsung
19 Chapin Rd. Building D,
Pine Brook, New Jersey 07058
QUESTIONS OR COMMENTS?
COUNTRY
IN THE US
CALL
1-800-SAMSUNG
(726-7864)
OR VISIT US ONLINE AT
WRITE
www.samsung.com/us/support
Samsung Electronics America, Inc.
85 Challenger Road
Ridgefield Park, NJ 07660
© 2017 Samsung Electronics Co., Ltd. All rights reserved.
AH68-02995Q-05
AH68-02995Q-05
Download PDF

advertising