Canon VB-M640VE Installation guide

Canon VB-M640VE Installation guide
BIE-7188-000
Caution
ENGLISH
Network Camera
Installation Guide
Please be sure to read the “Safety Precautions” section for correct use. After reading this Installation
Guide, keep it in a readily accessible location for future reference.
* Some cameras are not available in certain countries or regions.
Caution Request a professional installer for all installation work. Never try to install the camera yourself.
Doing so may result in unforeseen accidents such as dropping the camera or electric shock.
Check Included Items
•Do not move the lens unit by hand.
•Do not install on an unstable surface.
•To maximize shock resistant specifications, do not install on insufficiently strong surfaces or surfaces
subject to significant vibration.
•After turning off the power, do not turn the power on again for at least five seconds.
•Take measures to remove static electricity before performing any procedures.
•If there is condensation, please wait to power on, until the condensation dissipates.
•Please waterproof and dust-proof camera, when installing outdoors.
Failure to do so may result in malfunctions.
•Take care not to damage wiring or piping.
Failure to do so may result in damage to peripheral items.
Important
Installation Guide (This document)
•We recommend the installation of a lightning arrester (a surge protection device) as a measure against failures caused by
lightning strikes. Please refer to our website for details.
Dedicated accessory to protect the camera body from direct sunlight.
Heater Unit HU641-VB
Dedicated accessory attached to the interior of VB-M641VE to maintain operation temperature within the dome and
achieve stable operation even in extremely cold environments.
Conduit Adapter CA640-VB
Dedicated accessory used to protect the wiring cable to connect the pipe and the body.
Canon AC Adapter PA-V18
Dedicated AC adapter for this camera.
Symbols Indicating Safety Precautions
This Installation Guide uses the following symbols to indicate important information the user should know in order
to use the product safely. Explanations are provided for each symbol so that users will understand the level of
importance for each. Be sure to observe these items.
Warning
Failure to follow the instructions accompanied by this symbol may result in death or
serious injury.
Caution
Failure to follow the instructions accompanied by this symbol may result in injury.
Failure to follow the instructions accompanied by this symbol may result in property
damage.
Important This symbol indicates important or restricted items.
Note
Contains reference information for operation or additional explanations.
Safety Precautions
Installation Precautions
Warning
•Places in strong direct sunlight, near heat-generating objects, or locations subject to high
temperatures
•Places near fire sources or flammable solvents (alcohol, thinner, fuel, etc.)
•Places subject to oily smoke or steam
•Confined or enclosed places
Failure to do so may result in fire or electric shock.
•
Conduit Adapter
(sold separately)
•If you discover defective conditions such as smoke, strange sounds, heat or strange odors,
immediately stop using the camera and contact your nearest dealer.
Fire or electric shock may result from continued use of the product.
•If thunder starts, stop installation or inspection etc. and do not touch the camera or continue
connecting the cable.
•Do not disassemble or modify the camera.
•Do not damage the connecting cable.
•Do not insert foreign objects such as water or metal into the camera.
•Do not use flammable sprays near the camera.
•Do not leave LAN cables, external power supply, or the power connector for the AC adapter (sold
separately) connected when the camera is not in use for long periods.
•Do not use flammable solvents such as alcohol, paint thinner or benzine when cleaning the camera.
Failure to do so may result in fire or electric shock.
Insulate the ends of cables you are not using.
Failure to insulate will cause fire or electric shock.
Notes on Power Supply
•
Only use the dedicated AC adapter (sold separately) for AC power.
•Do not set any heavy objects on the power cable (or the LAN cable for a PoE power supply).
•Do not pull, forcibly bend, scratch, or modify the power cable (or the LAN cable for a PoE power
supply).
Do not cover or wrap the AC adapter (sold separately) with cloth or blankets.
•
Failure to do so may result in fire or electric shock.
Caution
For installation or inspection of this camera, consult the dealer where you purchased the product.
•This installation should be made by a qualified service person and should conform to all local codes.
•When installing, make sure the surface is capable of withstanding the total weight of the camera and
accessories, and sufficiently reinforce if necessary.
•Be sure to use installation screws designed for the type of surface the camera is to be installed.
•Periodically check the parts and screws for rust and loosening, in order to prevent injuries and
equipment damage due to falling items.
•Do not install in unstable places, places subject to significant vibration or impact, or places subject to
salt damage or corrosive gas.
•Do not install in places subject to strong winds.
•Do not install where snow can accumulate directly on the camera.
•Be sure to attach the safety wire when installing the camera.
Failure to do so may result in the camera falling or other accidents.
•Do not touch the edges of metal parts with bare hands.
•Be careful not to get your fingers caught when installing.
Failure to do so may result in injuries.
The contents of this guide are subject to change without any prior notice.
Dome flange
8
External Dimensions
Dome cover holder
Camera mounting tab slots
18
0
.09
)
Dedicated wrench
Unit: mm (in.)
Camera mounting tabs
4-M
172
Camera
.5
- 4
4(
4.
5
7)
(0
5
4.
.1
8)
(
*2)
10
*5)
(6.7
1,
) (*
8
0.1
8)
1
0.
(
83.5 (3-9/32) (*4)
85.7 (3-3/8) (*3, *4)
*1 Ceiling/Wall mount holes
*2 Junction box fixing holes
*3 Ceiling/Wall mount holes position
*4 Junction box fixing holes position
*5 Camera mounting holes
Unit: mm (in.)
Before Installing the Camera
Set the IP address and other network information on the camera using the “Camera Management Tool” on the
Setup CD-ROM.
For details on how to operate the “Camera Management Tool”, please refer to the “Camera Management Tool
User Manual”.
Removing the dome case and the lens rotation prevention tape
Remove the dome case, then remove the tape preventing the lens from rotating which was attached for shipping.
Dedicated wrench
❷
Dedicated wrench
❸
❶
❹
❺
Others
Operating Environment
Temperature:
– Sunshade Cover (sold separately) necessary when under direct sun exposure
When the heater unit (sold separately) is installed
Operating Temperature Range:
AC: -40°C – +55°C (-40°F – +131°F)
DC, PoE: -10°C – +55°C (+14°F – +131°F)
Start-up Temperature Range:
AC: -30°C – +55°C (-22°F – +131°F)
DC, PoE: -10°C – +55°C (+14°F – +131°F)
When the heater unit (sold separately) is not installed
AC, DC, PoE: -10°C – +55°C (+14°F – +131°F)
Humidity: 5% – 85% (without condensation)
Temperature:
PoE: -10°C – +55°C (+14°F – +131°F)
– Sunshade Cover (sold separately) necessary when under direct sun exposure
Humidity: 5% – 85% (without condensation)
Storage Environment Temperature: -30°C – +60°C (-22°F – +140°F)
Humidity: 5% – 90% (without condensation)
Installation Method
Ceiling mount/Surface mount
Power Supply
PoE: P
oE power supply via LAN connector (IEEE802.3at Type1 compliant)
AC Adapter: PA-V18 (100 – 240 V AC) (sold separately)
External power source: 24 V AC/12 V DC
PoE: PoE power supply via LAN connector (IEEE802.3at Type1 compliant)
Dome cover
(7
Please refer to the installation procedures or the Appendix – Specifications for specifications not listed below.
Network Terminal*
LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))
* Use a category 5 or better LAN cable, 100 m (328 ft.) or less in length.
Audio Input Terminal
3.5 mm ( 0.14 in.) mini-jack connector (monaural)
(Common for LINE IN & MIC IN)
LINE IN (connect to an amplifier microphone) or
MIC IN (connect to a microphone w/o amplifier)
Switch LINE IN/MIC IN in the Setting Page.
Audio Output Terminal 3.5 mm ( 0.14 in.) mini-jack connector (monaural)
(LINE OUT)
LINE OUT (connect to an amplifier speaker)
External Device I/O Terminal
Input x 2, Output x 2
Memory Card *
microSD Memory Card, microSDHC Memory Card, microSDXC Memory Card Compatible.
*T
o insure reliability in the recording speed, it is recommended to use CLASS 10 rated products.
Even when using CLASS 10 products, reliability cannot be guaranteed during heavy access loads (e.g., when
recording and deleting data at the same time).
Rubber seal
Smoked dome cover
131 (5.16)
Specifications
2.4x optical zoom (4x digital zoom) lens (electric drive)
For 16:9 aspect ratios
Horizontal: 111.5° (W) – 46.2° (T)
Vertical: 60.5° (W) – 25.9° (T)
For 4:3 aspect ratios
Horizontal: 111.5° (W) – 46.2° (T)
Vertical: 81.7° (W) – 34.6° (T)
Day Mode (color):
0.02 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
Night Mode (monochrome):
0.001 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
When using the Dome Unit (Smoked) (sold separately)
Day Mode (color):
0.04 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
Night Mode (monochrome):
0.002 lux (F1.2, shutter speed 1/30 sec., when smart shade control is off, 50IRE)
350° (±175°)
150° (±75°)
350° (±175°)
MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
7
1. Dome case lock screw / 2. Interface cover / 3. Dome case / 4. LED (Blue)* / 5. Lens unit / 6. Reset switch /
7. Reboot switch / 8. Memory card slot / 9. Power connection terminal
/
10. External device I/O terminals
/
11. Audio input terminal (Black) (common LINE IN and MIC IN)
/
12. Audio output terminal (White) (LINE OUT)
/ 13. 100Base-TX LAN connector
* On: when powered on, during reboot / Off: during normal use
4.8
(0.19)
Interface
Do not install in the following places:
6
Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Warning
Lens
Viewing Angle
Min. Subject Illumination
Pan Angle Range
Tilt Angle Range
Rotation Angle Range
4
3
Precautions for Use
Sunshade Cover SC640-VB
Caution
2
4.5 (0.18)
18.5 (0.73)
85.7 (3-3/8) (*3)
Smoked dome cover.
•Take care when replacing so as not to scratch the dome cover.
•For proper protection against water and dust, please make sure the screws are firmly tightened during installation.
5
)
Dome Unit DU640-S-VB
Important
97
Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, such as in big-box
stores.
Remove the dome case from the camera, then remove the dome cover holder and dome flange, and replace with
the smoked dome.
1.
Pendant Mounting Kit PC640-VB
Using the Dome Unit (sold separately)
(R
The following accessories can be purchased separately as necessary. Some accessories are not available in
certain countries or regions.
❷
0
Accessories
❶
13
R5
Printed in Japan
When installing the camera outdoors, observe the following precautions to retain
waterproof/dustproof capabilities.
•Use the sunshade cover (sold separately) when installing in a location with direct
sunlight.
•Completely wrap the cable connections and the ends of cables you are not using,
including the connectors, with waterproof tape up to the cable jacket, so as not to
allow water to enter. Please refer to the waterproofing explanation sheet for details on
how to wrap the waterproofing tape.
•When mounting the camera onto a wall or other upright surface, make sure that the
cables and composite pipe are facing down to prevent rain infiltration.
•If wiring by connecting the camera to the composite pipe (3/4 inch NPSM threaded
hole), bridge the gap using the conduit adapter (sold separately). When connecting
the conduit adapter and the pipe, wrap Teflon tape around the tip of the pipe
to prevent water getting in as necessary, clear any debris, and firmly tighten. If
necessary, apply silicon sealant to seal it tightly after attaching the pipe.
•Firmly fix the dome case to the main unit of the camera with the lock screws, taking
care not to pinch cables between the main unit and dome case.
❸
11
10
9
Precautions for Installing the Camera Outdoor
Camera specific functions will be listed using the symbols below.
: VB-M641VE
: VB-M640VE
© CANON INC. 2017
12
1
Dedicated wrench
Symbols Indicating Camera Model
Connect the two heater cables included with the heater unit, to the terminals on the camera side. Next, attach the
heater unit to the camera body and then tighten the screws. Finally, connect the cables to the heater unit.
Part Names
46.0 (1-13/16) (*4)
Camera, Screws (M4) x 4
Template
Setup CD-ROM
Warranty Card
Safety Wire, Screws (M4) x 1
Ceiling Plate
Power Interface Cable
I/O Interface Cable (BK2-0035-000)
Waterproofing Tape
Waterproofing explanation sheet
PoE: Max. approx. 8.9 W*1
AC Adapter PA-V18: Max. approx. 10.5 W (100 V AC)
Max. approx. 10.6 W (240 V AC)
DC: Max. approx. 9.5 W
AC: Max. approx. 9.1 W
Max. approx. 21.7 W*2
*1 Class 0 power sourcing equipment (requests 15.4 W)
*2 When the heater unit (sold separately) is installed
PoE: Max. approx. 8.9 W*
* Class 0 power sourcing equipment (requests 15.4 W)
Weight
Approx. 1620 g (3.58 lb.)
Approx. 1590 g (3.51 lb.)
Impact Resistance
IK10 (20J)
Dust-resistant/
Waterproof SpecificationIP66
85.7 (3-3/8) (*4)
/
Using the Heater Unit (sold separately)
Power Consumption
Using a Memory Card
Remove the dome case and place the memory card in the memory card slot.
To remove the memory card, push it in all the way until the card slightly pops
out and remove.
Important
Memory card slot
•Insert a memory card before installing the camera.
•When using a memory card with the camera for the first time, it is recommended
to format the card after inserting it into the camera (please refer to the “Operation
Guide”).
•Always unmount the memory card before removing it (please refer to the
“Operation Guide”).
Using the Sunshade Cover (sold separately)
The sunshade cover is attached to the camera body together with
the dome case. In order to install it, of the four lock screws for the
dome case, remove the two located at the top of the dome case
beforehand. The dome case lock screws can be removed by
pressing and loosening from the inside of the case.
Dedicated wrench

Connecting the Camera
To prevent cable connections from shorting out, wrap each individual connection with insulating tape, and then
wrap all of the cables with waterproofing tape.
1
Power Connection
Directly attached to ceilings/Directly attached to walls
1 -1
Power can be supplied to the camera in the three ways described below. Please be sure to read the user manual
for the dedicated power supply before use.
1 -2
Ceiling Installation
a
Note
Note
Wrap the cable connection with
waterproof tape.

PoE (Power over Ethernet)
The camera supports PoE functions. Power can be supplied to the camera by using a LAN cable connected to a
PoE HUB that conforms to the IEEE802.3at Type1 standard.
d. I/O interface cable
e. Power interface cable
Important
•Check with your dealer for more information about PoE HUB and Midspan technology.
Midspan (a LAN cable power supply device) is a device that, like a PoE HUB, supplies power to the camera via a LAN
cable.
•Some PoE HUBs allow the limitation of power for each port, but applying limits may interfere with performance. If using
this type of PoE HUB, do not limit the operating power.
•Some PoE HUBs have limits for the total power consumption for the ports, which can interfere with performance when
multiple ports are in use. For more information, check the instruction guide for your PoE HUB.
•
When the camera is connected to both a PoE HUB and an external power supply (12 V DC or 24 V AC), power
from the power supply first connected is given priority. But when both power supplies are connected, according to the
combination, problems such as failure of the network connection may occur. If a problem arises, disable one of the power
supplies.
Wall Installation
4
a. Template
5
1 -3
b
b
❷

External Power Supply
12 V DC or 24 V AC input can be used. Use the included interface cable to connect to the camera power
connection terminal.
❶
1: BROWN Power 24 V AC / 12 V DC non-polar
2: BLUE Power 24 V AC / 12 V DC non-polar
3: GREEN FG (frame ground)
1
Dedicated wrench
3
b. Ceiling plate
If the cables cannot be stored above a ceiling
Interface cover
Remove the interface cover and pass the cable through. You can also use
the conduit adapter (sold separately) to connect with the composite pipe (3/4
inch NPSM threaded hole). If you use the conduit adapter, please refer to the
Installation Guide included with the adapter.
6
External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets have no polarity.
Controls from the Viewer can be used to open and close the circuit between the terminals. Using optical couplers,
the output terminals are isolated from the camera’s internal circuit.
The load connected to the output terminals should be within the following rating range.
Rating between output terminals:
Internal Connection Diagram
Maximum voltage 50 V DC
+3.3 V
Continuous load current at or below 100 mA
1 kΩ
10 kΩ
10 kΩ
On resistance: Max. 30 Ω
•Power supply should conform to all local codes.
•The power supply should also comply with IEC/UL60950-1 (SELV/LPS) standards.
•
Please only use 24 V AC as a power source when using the Heater Unit HU641-VB (sold separately) . PoE,
12 V DC and AC Adapters cannot be used.
d
e
a
External Device Output Terminals (OUT1, OUT2)
Internal controller
3
Installing the Camera
Input terminal
IN1, IN2
External device
Output terminal
OUT1, OUT2
Audio Input/Output Terminals
Each audio input/output terminal has one input system and one output system.
Connecting the camera to an audio input/output device such as a microphone or a speaker with an amplifier
allows you to send/receive audio through the Viewer.
Use the 3.5 mm ( 0.14 in.) monaural mini-jack connector to connect an audio input/output device.

Audio Input Terminal Common LINE IN/MIC IN (monaural input)
Although the camera only has a single audio input system, it supports two types of microphone input: LINE IN and
MIC IN. Before using the audio input, please confirm the [Audio Input] on the Setting Page (please refer to the
“Operation Guide”). LINE IN is selected by default.
Input terminal: 3.5 mm ( 0.14 in.) mini jack (monaural)
•Dynamic MIC IN
Input impedance: 1.5 kΩ ±5%
* Supported microphones: Output impedance: 400 – 600 Ω
•Condenser MIC IN
Input impedance (microphone bias resistance): 2.2 kΩ ±5%
Microphone power supply: plug-in power (voltage: 2.3 V)
* Supported microphones: Condenser microphones with plug-in power support
•LINE IN
Input level: Max. 1 Vp-p
* Use a microphone with an amplifier.

Audio Output Terminal LINE OUT (monaural output)
Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from Viewer.
Output terminal: 3.5 mm ( 0.14 in.) mini jack (monaural)
Output level: Max. 1 Vp-p
* Use a speaker with an amplifier.
12 V DC can be connected in a non-polar configuration.
7
External device
0.1 µF
Important
•The power supply should be within the following voltage range.
•24 V AC: Voltage fluctuation within ±10% of 24 V AC (50 Hz or
60 Hz ±0.5 Hz or less) Current supply capacity of at least 1.0 A per camera
•12 V DC: V
oltage fluctuation within ±10% of 12 V DC Current supply capacity of at least 1.5 A per camera
•When using a 12 V DC battery power supply, be sure to connect resistors of at least 0.5 – 1.0 Ω/20 W in series to the
power line.
•For an external power supply, use a double-insulated device.
Recommended Power Cables [Reference]
Cable (AWG)
Attaching to a junction box
Attach the ceiling plate to the junction box after confirming the fixing holes locations with the external
dimensions diagram.
Dedicated wrench
Mount using the Pendant Mounting Kit (sold separately).
For details please refer to the Installation Guide included with the kit.
1 -1
1 -2
22
20
18
16
5
(16.4)
9
(29.5)
14
(45.9)
23
(75.5)
32
(105.0)
24 V AC maximum cable lengthm
(ft.)
11
(36.1)
18
(59.1)
29
(95.1)
46
(150.9)
64
(210.0)
Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring.
M4 × 4
Screws
(included)
Ceiling pendant mounting
24
12 V DC maximum cable lengthm
(ft.)

AC Adapter
Please use the dedicated AC adapter (sold separately).
Remove the power connector with the attached AC adapter, then connect the power interface cable from the
power connector included in the package, as shown in the following diagram.
Attaching the sunshade cover (sold separately)
❷
Power Interface
Cable
Green
❸
❶
Greater than 25 mm (1.0 in.)
M3*
*Included
with Pendant
Mounting Kit
M4* × 4
External device I/O terminals consist of two input and output systems each. Viewer can be used to check external
device input status and control output to an external device (please refer to the “Operation Guide”).
Use the included I/O interface cable to connect to external device input/output terminals.
1: BROWN External device input 1 IN1 (+)
2: BLACK External device input 1 IN1 (-)
3: RED
External device input 2 IN2 (+)
4: BLACK External device input 2 IN2 (-)
5: ORANGE External device output 1 OUT1
6: YELLOW External device output 1 OUT1
7: GREEN External device output 2 OUT2
8: BLUE External device output 2 OUT2
1
8
8
When the installation has finished, please adjust the angle. For more information, please refer to the
“Operation Guide”.
2

Rebooting/Resetting the Camera
❷
c
M4
Screws (included)
White
External Device I/O Terminals
❹
Dedicated wrench
❶
Blue
AC Adapter
Black
Insulate
Pass necessary cables
for connecting the camera
through the pipe.

Rebooting
To reboot the camera by turning its power off and on, remove the
dome case and press the reboot switch.
❸
External Device Input Terminals (IN1, IN2)
External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative terminals
connected to the camera interior GND. Connecting cables to the positive and negative terminals and opening or
closing the circuit notifies the Viewer.
Important
•When connecting sensors and switches, connect terminals that are electrically isolated from the respective power and
GND.
Note
Rebooting can be done from the camera settings page as well (please refer
to the “Operation Guide”).

LED
c. Safety wire
Brown
Reboot switch
Reset switch
Resetting
To reset the camera to its factory default settings, press the reset
switch and reboot switch while checking the LED display in the
following order.
1) Hold the reset switch down, and press the reboot switch with a
pointed object.
2) After holding down the reset switch for at least three seconds,
release the reboot switch.
3) After the LED starts to blink, release the reset switch. When the
blinking has stopped, the unit has finished resetting.
Only for European Union and EEA (Norway, Iceland and Liechtenstein)
These symbols indicate that this product is not to be disposed of with your household waste, according to
the WEEE Directive (2012/19/EU), the Battery Directive (2006/66/EC) and/or national
legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in accordance with the
Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb =
Lead) is present in this battery or accumulator at a concentration above an applicable
threshold specified in the Battery Directive.
This product should be handed over to a designated collection point, e.g., on an authorized one-for-one
basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and
electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could
have a possible impact on the environment and human health due to potentially hazardous substances that
are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the
effective usage of natural resources.
For more information about the recycling of this product, please contact your local city office, waste authority,
approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www.
canon-europe.com/battery.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement