Aeg-Electrolux | 6310K-M | User manual | Aeg-Electrolux 6310K-M User Manual

6310 K
GB
374 4247 16 / 11.04
INSTRUCTION BOOK
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
1
Service
Congratulations from AEG
Before calling service – Technical advice
Dear Customer,
Sympton
Solution
Congratulations with your new Hob.
The hob is not working
Check your earth leak circuit breaker.
Check fuses.
The hob becomes hot
The ceramic hob will reach a
temperature of 80˚C. It may, however,
become even hotter if you use cooking
utensils with uneven bases or which
does not match the size of the cooking
zone.
The fuses keep blowing
Too many electrical appliances may be
in use at the same time. If the hob is
connected to a 10 Amp fuse group, the
risk of overloading will be
considerable.
The cooking zones do not heat
sufficiently
The cooking utensils must match the
size of the cooking zone. Check that
the cooking utensils have level bases
by holding them against the edge of the
work top, for example. Bring a litre of
water to the boil in a saucepan with a
lid. The cooking zone should be
adjusted to the highest setting.
The boiling time on the 12 cm cooking
zone is approx. 25 min.
The boiling time on the 14 cm cooking
zone is approx. 13 min.
The boiling time on the 18 cm cooking
zone is approx. 10 min.
It is important that you become familiar with the functions and features of
the Hob. You should therefore read these operating instructions as they will
help you get the most out of your new Hob.
Pay extra attention to sections marked
. These are warning texts to help
you avoid accidents.
Keep the operating instructions. They will come in handy if there is
something you are not sure about, and should accompany the Hob if it is
transferred to a new owner.
The structure of the operating instructions enables you to use them as a
reference manual. The first part of the operating instructions contains a
general description of your new product. Then follows a short introduction
of the things to do before you use the Hob for the first time. The section
“How to use” describes how the Hob is used in everyday life. Use this
section until you are familiar with your new Hob. The section “Cleaning
and Maintenance” provides information on both daily and more thorough
cleaning of the individual components of the Hob. Should problems arise
when you use the Hob, you can look in the section “Before calling service”,
where there are instructions on how to remedy some practical and technical
problems yourself.
Enjoy!
Regards,
2
19
Technical specifiacations
Table of contents
Two-phases zero-earth
Cable type 1,5 mm² HO5VV-F.
The cable outside diameter must be
between 7,5 and 10,5 mm.
Contents
no
Your new appliance ...................................................................................... 2
Safety information ........................................................................................ 4
Description of the product ......................................................................... 5
Control button ....................................................................................... 5
Panel .................................................................................................... 5
Glass ceramic surface .......................................................................... 6
Zones .................................................................................................... 6
Pilot light ............................................................................................... 6
Residual heat indicator .......................................................................... 6
Before use .................................................................................................... 7
Operating instructions ................................................................................ 8
Advice and hints for using the cooking zones ....................................... 9
Cleaning and maintenance ....................................................................... 11
Panel .................................................................................................. 11
Stainless steel surfaces ....................................................................... 12
The ceramic glass hob ........................................................................ 12
Tips on the use of the ceramic hob unit .............................................. 13
Service
.................................................................................................. 19
Before calling service – technical advice ........................................... 19
For the user
Cell Voltage 240 V
Electrical connection
240V - 50Hz
Total wattage 6400W
Instant heat effect
Left front
21 cm
Left Back
14 cm
Right back
12/18 cm
Right front
14 cm
Page
2300 W
1200 W
700/1700W
1200 W
This unit is labelled to indicate
conformity with the lowvoltage directive
(73/23/EEC) and the EMC directive
(89/336/EEC).
Unpacking
For the installer
hobs the nameplate.
Write the serial number on the cover
of these operating instructions to make
it easy to find in case of service.
Check that the hob has no faults and
is undamaged on delivery.
Transport damage
Any damage from transport which
you have not carried out yourself must
be reported to the retailer within one
week of receipt.
You will find the serial number of the
Mounting .................................................................................................. 15
Installation .................................................................................................. 17
Technical specifications ............................................................................ 18
Unpacking .................................................................................................. 18
How to read the operating instructions:
1... 2...Step by step
Hint and tips
Safety information
18
Environmental information
3
Safety information
Never leave the hob unattended while
deep fat frying, or heating fats and oils.
The appliance is not intended for use
by young children or infirm persons
without supervision.
These warnings are provided in the
interests of your safety. Ensure you
fully understand them before installing
or using the appliance. Your safety is of
paramount importance. If you are
unsure about the meaning of these
warnings contact the Customer Care
Department for assistance.
Child Safety
Young children should be supervised
to ensure that they do not play
with the appliance
The hob gets hot when it is in use.
Children should be kept away until the
hob has cooled.
Installing
Do not install the hob if the ceramic
glass is damaged or cracked.
This hob must be installed according to
the instructions supplied. Any
installation work must be undertaken
by a qualified competent person.
Do not alter the specifications or
attempt to modify the appliance in any
way.
Maintenance and Cleaning
Only clean this hob in accordance
with the instructions given in this
book.
Service
Repairs carried out by inexperienced
persons may cause injury or serious
malfunction of the appliance. Repairs
must only be carried out by a
qualified/competent person. Contact
your local AEG Service Centre.
During Use
The hob is intended for domestic
cooking only. It is not designed for
commercial/industrial purposes.
Ensure that all the control knobs are in
the OFF position when not in use.
Do not use the hob if it is damaged in
any way, contact your local AEG
Service Centre.
Never use plastic or aluminium dishes
on the hob.
Disposal
Make the hob unusable by cutting off
the cable.
Dispose of any packaging material and
old appliances at an authorised
disposal site.
on the product or on its packaging indicates that this
The symbol
product may not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of
this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
4
Electrical installation
The electrical connection may only be
performed by a qualified electrician/
competent person. The electrical
connection must be carried out in
accordance with prevailing regulations
for appliances using heavy current.
The connection must comply with any
specific requirements specified by the
local electricity supply authority.
There must be no interference with
any of the unit’s electrical parts.
The cable is mounted in the pegs as
shown.
Unscrew the cover while connecting
the cables.
A unit led directly to the power point
or the outlet rose.
More units may be connected via one
or more junction boxes.
The cable must be connected via an
external switch with a contact
separation of at least 3 mm in each
pole.
Please observe these instructions,
otherwise the warranty will not
cover any damage that may occur.
Single-phase zero-earth
Cable type 1,5 mm² HO5VV-F.
The cable outside diameter must be
between 7,5 and 10,5 mm.
17
Description of the product
It is not necessary to attach the
reinforcement beam to the work top
surface, as it is held in place by a
specially designed moulding, which is
incorporated in the hob units flanges.
The units externally measured
length
145 mm:
Cooker hood
Control button
290 mm:
Two-zone ceramic-top electric hob
Two-burner gas hob
Grill
Fryer
Wok
580 mm:
Four-zone ceramic-top electric hob
Four-burner gas hob
Panel
725 mm:
Four-zone ceramic-top electric hob
Installation of a single unit
When mounting a single unit, be it a
half-or full size unit, in a
worktopsurface which is thicker than
30 mm, it is necessary to make a
special notch in both sides of the cutout hole, as shown in the adjacent
drawing.
The purpose of these notches is to
create space for the electrical cables.
Controlbutton for operations
16
5
Mounting
Caution: In order to avoid a hazard this
appliance must be installed according to
these instructions for installation
Glass ceramic surface
The glass ceramic surface has four
zones. When a zone is turned on it
is illuminated at various intervals
depending on the setting chosen.
Even at the highest setting the zone
is disconnected occasionally to
ensure that the surface is not overheated.
The glass is hard, and has been
tempered to withstand heat, cold
and temperature shocks. But like all
glass it is sensitive to impact. Do
not stand on the glass ceramic
surface - it cannot withstand
abnormal loads.
Min. 47 mm
The appliance unit can be mounted in
any type of kitchen with a work top
whose thickness is between 28 mm and
40 mm.
Clearance
The distance between the top side of the
work top and the carpentry underneath
must be at least 47 mm.
Fixing
There are tree single zones and one
double zone.
Screw the fixing brackets out to such an
extent that they can be turned in under
the work top. Tighten the brackets on to
the work top with an ordinary
screwdriver.
Pilot light
Cut-out measurements
Pilot light is activated when either
of the plates are turned on, and will
remain on until the plates are
switched off.
One rectangular hole is sawn out for the
appliance combination chosen.
The depth of the cut-out for any unit is:
490 mm
Length of hole = sum of all units`
externally measured length, less 20 mm.
Zones
Residual-Heat indicator
Each plate has a residual heat
indicator which remains on as long
as the temperature of the plate
exceeds 80˚C, even if the plate is
switched off.
Minimum distance
to wall:
150 mm
Reinforcement
beams
Mounting of Reinforcement
Beams
A reinforcement Beam, with supporting
flanges at each end, is included with
each two-burner unit. For unit
combinations, a reinforcement beam
must be used between each unit.
6
15
Minimum distance
to wall (nonflammable material):
50 mm
Before use
Warning:
Aluminium foil and plastic utensils are
not to be placed on hot surfaces.
The surface may not be used for
storage.
The decorative pattern on the ceramic
surface can become scratched and
marred with use, depending upon
maintenance, but does not adversely
affect performance.
Such blemishes are not covered by the Do not stare at the heating units
when in operation.
warranty.
Spills and melts must be removed
immediately, while the burner is still
warm, using the scraper supplied with
the unit. Especially damaging are melted
plastic, aluminium, or any foodstuff
containing sugar, including natural sugar,
as these can create permanent
“pockmarks” and craters on the ceramic
surface. After scraping polish thoroughly
with the cleaning agent supplied with the
unit.
Utensils which have been in contact with
the above-mentioned melted materials
must be cleaned thoroughly before used
again on the ceramic-top hob unit.
Protection of the glass
ceramic surface
A protective film should be applied
to the glass ceramic surface before
use. This will make it easier to
clean the surface, as well as
preventing substances from being
burnt onto the surface.
This is what to do:
1. Pour a few drops of ceramic
cleaning detergent such as
vitroclen onto a piece
of kitchen roll and rub the
detergent into the entire surface.
2. Polish the surface with a clean
cloth until it is dry.
Defects in the ceramic surface which can
be related to the above are not covered
by the warranty.
Utensils with aluminium bottoms can
cause light spots on the ceramic surface.
These can be removed with the cleaning
agent supplied with the unit.
14
7
Operating instructions
Switch symbols (to the left)
Switch for regulating the plate at
the rear
Pilot light
Switch for regulating the large
plate at the front.
Tips on the use of the
ceramic hob unit
Do not slide saucepans across the
surface of the hob - always lift the pan
when placing it on, or removing it
from the ceramic surface.
Wipe the bottom surface of the pots
and pans with a clean dry cloth before
placing them on the ceramic surface.
This helps to reduce cleaning and
prevents scratching the hob glass.
Switch for regulating the double
plate at the rear
Switch for regulating the small
plate at the front.
Wipe off spills whilst the hob is warm.
Select the highest setting for the
cooking zones until the food is brought
to the boil, then reduce the setting.
Regulating
The regulating of heat is graduation-free
for all plates on a scale from 1 to 12.
“1”
Represents lowest heat
“12” Represents maximum heat.
“0”
Represents “OFF”.
Use saucepans with an even base. An
uneven based saucepan may increase
the electricity consumption by up to
50%.
Small circle: When you switch on the
cooking section it will always be the
small circle that is switched on. Choose
the wanted temperature.
The saucepan should match the
cooking zone or be slightly larger.
Use a tightly fitting lid on the saucepan
to reduce electricity consumption.
From small to big circle (both circles
are on): Turn the button past “12” to
stop. Turn back to the wanted
temperature.
From big to small circle: Turn the
button back to “0”. Switch on again and
choose the wanted temperature.
8
13
Stainless steel surfaces
Clean the appliance after use with a
soft cloth well wrung out in warm
water, use a small amount of liquid
detergent for stubborn soiling.
Stainless steel parts may become straw
coloured with use, use a proprietary
stainless steel cleaner to remove this
straw discolouration.
Never use metal wool, metal sponges
or other abrasive cleaning agents.
The ceramic glass hob
3. Wipe the ceramic hob clean with
a damp cloth or kitchen roll.
Tough stains can be removed by
rubbing the stain hard with
kitchen roll.
4. Wipe off remaining cleaning
agent with a damp cloth.
5. Wipe with a dry cloth, if
required.
Make sure that the ceramic hob is dry
when you heat it up again. Ceramic
hobs can develop rainbow-like stripes
if heated while damp.
Immediately scrape off stains caused
by food which has boiled over using
the scraper supplied with the hob,
spilled sugar, dishes containing sugar
(jam, juice, etc.), melted plastic and
aluminium foil while the ceramic hob
is still hot. If the ceramic hob is
allowed to cool it may become
damaged. A dirty ceramic hob
decreases the heat transfer between
cooking zones and cookware.
over will burn onto the hot
cooking zone.
Advice and hints for using the
cooking zones
If you use the advice below
you will save energy and
make your cleaning tasks
easier.
Saucepans with very
shiny/bright bases will
prolong the cooking time
slightly compared with
cooking utensils with
matt/dark bases.
Adjust the cooking zones
correctly. Select the highest setting
for the cooking zones until the food is
brought to the boil. Then reduce the
setting as far as possible, without the
food going off the boil.
Use a tightly fitting lid on the
saucepan. Without a lid you
use more than three times as
much electricity.
Use level saucepans. An
uneven saucepan may
increase the electricity
consumption by up to 50 per
cent. Check whether your
saucepans have level bases
by placing the item in question
upside down on a work top and
positioning a ruler on the base.
A curved base, both inwards and
outwards, will prolong the
cooking time and increase the
energy consumption
After use the cooking zones should be
wiped with a damp cloth with washing
up liquid. For severe soiling you can
follow these steps:
The saucepan should match
the cooking zone – or be
slightly larger. Remember
that a large saucepan can also
hold small quantities. If the
diameter of the base is too small,
the energy consumption will
increase, and any food boiling
1. Remove stains etc., with the
ceramic hob scraper.
2. Make sure that the ceramic hob
has cooled down. Use a ceramic
cleaning agent, such as vitroclen.
12
9
Cleaning and maintenance
Check whether your cooking utensils
has level bases by placing the item in
question upside down on a work top
and positioning a ruler on the base. A
curved base, both inwards and
outwards, will prolong the cooking
time and increase the energy
consumption. If the diameter of the
base is too small, the energy
consumption will increase, and any
food boiling over will burn onto the
hot cooking zone.
Cooking utensils with very
shiny/bright bases will prolong the
cooking time slightly compared with
cooking utensils with matt/dark bases.
For reasons of hygiene and
safety, the cooking zones
must be kept clean. Grease
stains and spilled food
generate smoke when heated,
and can even cause fire.
The splashguard can be removed to
make it easier to clean the surface.
What to do:
1. Hold the splashguard as shown
in the diagram.
2. Lift the splashguard straight up
3. Clean the top surface as
described in “cleaning the steel
surface”.
Be aware of the two retaining
pegs, which are sharp.
4. Replace the splashguard in
position ENSURE that it is
fitted the correct way round.
Never use hard or sharp
implements to lift off the
splashguard.
Do not wash the splashguard
in a dishwasher.
The hob must not be used
with the splashguard off.
10
11
Download PDF

advertising