Zanussi | ZOP38903XK | User manual | ZANUSSI ZOP38903XK User Manual

EN
User manual
Oven
ZOP38903
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _
Product description _ _ _ _ _ _ _ _ _ _ _ _ _
Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Clock functions _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2
3
5
6
6
8
Additional functions _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 10
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ 16
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 19
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20
Environment concerns _ _ _ _ _ _ _ _ _ _ _ 21
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always
keep the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are supervised by an adult or a person who is responsible for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep children and pets away from the appliance when it operates
or when it cools down. Accessible parts are hot.
• If the appliance has a child safety device, we recommend that you
activate it.
• Cleaning and user maintenance shall not be made by children
without supervision.
General Safety
• Internally the appliance becomes hot when in operation. Do not
touch the heating elements that are in the appliance. Always use
oven gloves to remove or put in accessories or ovenware.
• Do not use a steam cleaner to clean the appliance.
2
www.zanussi.com
• Before maintenance cut the power supply.
• Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the glass door since they can scratch the surface, which
may result in shattering of the glass.
• Excess spillage must be removed before the pyrolytic cleaning.
Remove all parts from the oven.
• To remove the shelf supports first pull the front of the shelf support and then the rear end away from the side walls. Install the
shelf supports in the opposite sequence.
Safety instructions
Installation
Warning! Only a qualified person must
install this appliance.
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Obey the installation instruction supplied
with the appliance.
• Always be careful when you move the appliance because it is heavy. Always wear safety
gloves.
• Do not pull the appliance by the handle.
• Keep the minimum distance from the other
appliances and units.
• Make sure that the appliance is installed below and adjacent safe structures.
• The sides of the appliance must stay adjacent to appliances or to units with the same
height.
Electrical connection
Warning! Risk of fire and electrical shock.
• All electrical connections should be made by
a qualified electrician.
• The appliance must be earthed.
• Make sure that the electrical information on
the rating plate agrees with the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
www.zanussi.com
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Contact the
Service or an electrician to change a damaged mains cable.
• Do not let mains cables to come in touch
with the appliance door, specially when the
door is hot.
• The shock protection of live and insulated
parts must be fastened in such a way that it
cannot be removed without tools.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• If the mains socket is loose, do not connect
the mains plug.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Use only correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips
and contactors.
• The electrical installation must have an isolation device which lets you disconnect the appliance from the mains at all poles. The isolation device must have a contact opening
width of minimum 3 mm.
3
• Fully close the appliance door, before you
connect the mains plug to the mains socket.
Use
Warning! Risk of injury, burns or electric
shock or explosion.
• Use this appliance in a household environment.
• Do not change the specification of this appliance.
• Make sure that the ventilation openings are
not blocked.
• Do not let the appliance stay unattended
during operation.
• Deactivate the appliance after each use.
• Be careful, when you open the appliance
door while the appliance is in operation. Hot
air can release.
• Do not operate the appliance with wet hands
or when it has contact with water.
• Do not apply pressure on the open door.
• Do not use the appliance as a work surface
or as a storage surface.
• Always keep the appliance door closed when
the appliance is in operation.
• Open the appliance door carefully. The use
of ingredients with alcohol can cause a mixture of alcohol and air.
• Do not let sparks or open flames to come in
contact with the appliance when you open
the door.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
Warning! Risk of damage to the
appliance.
• To prevent damage or discoloration to the
enamel:
– do not put ovenware or other objects in the
appliance directly on the bottom.
– do not put aluminium foil directly on the
bottom of the appliance.
– do not put water directly into the hot appliance.
4
– do not keep moist dishes and food in the
appliance after you finish the cooking.
– be careful when you remove or install the
accessories.
• Discoloration of the enamel has no effect on
the performance of the appliance. It is not a
defect in the sense of the warranty law.
• Use a deep pan for moist cakes. Fruit juices
cause stains that can be permanent.
Care and Cleaning
Warning! Risk of injury, fire or damage to
the appliance.
• Before maintenance, deactivate the appliance and disconnect the mains plug from the
mains socket.
• Make sure the appliance is cold. There is the
risk that the glass panels can break.
• Replace immediately the door glass panels
when they are damaged. Contact the Service.
• Be careful when you remove the door from
the appliance. The door is heavy!
• Clean regularly the appliance to prevent the
deterioration of the surface material.
• Remaining fat or food in the appliance can
cause fire.
• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
• If you use an oven spray, obey the safety instructions on the packaging.
• Do not clean the catalytic enamel (if applicable) with any kind of detergent.
Pyrolytic cleaning
Warning! Risk of fire and burns.
• Before carrying out a Pyrolitic self-cleaning
function or the First Use function please remove from the oven cavity:
– Any excess food residues, oil or grease
spills / deposits.
– Any removable objects (including shelves,
side rails etc., provided with the product)
www.zanussi.com
•
•
•
•
•
particularly any non-stick pots, pans, trays,
utensils etc.
Read carefully all the instructions for Pyrolytic
cleaning.
Keep children away from the appliance while
the Pyrolytic cleaning is in operation. The appliance becomes very hot.
Pyrolitic cleaning is a high temperature operation that can release fumes from cooking
residues and construction materials, as such
consumers are strongly advised to:
– Provide good ventilation during and after
each Pyrolytic cleaning.
– Provide good ventilation during and after
the first use at maximum temperature operation.
– Remove any pets (especially birds) from
the vicinity of the appliance location during
and after the Pyrolytic cleaning and first
use maximum temperature operation to a
well ventilated area.
Unlike all humans, some birds and reptiles
can be extremely sensitive to potential fumes
emitted during the cleaning process of all Pyrolytic Ovens.
Small pets can also be highly sensitive to the
localized temperature changes in the vicinity
of all Pyrolytic Ovens when the Pyrolytic self
cleaning program is in operation.
• Non-stick surfaces on pots, pans, trays,
utensils etc., can be damaged by the high
temperature Pyrolytic cleaning operation of
all Pyrolytic Ovens and can be also a source
for low level harmful fumes.
• Fumes released from all Pyrolytic Ovens /
Cooking Residues as described are not
harmful to humans, including infants or persons with medical conditions.
Internal light
• The type of light bulb or halogen lamp used
for this appliance, is only for household appliances. Do not use it for house lighting.
Warning! Risk of electrical shock.
• Before replacing the lamp, disconnect the
appliance from the power supply.
• Only use lamps with the same specifications.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Product description
2 Grill
3 Oven lamp
1
2
5
3
4
7
3
4
2
1
6
5
1 Electronic programmer
www.zanussi.com
4 Fan
5 Shelf support, removable
6 Rating plate
7 Shelf positions
Oven accessories
• Wire shelf
For cookware, cake tins, roasts.
• Aluminium baking tray
For cakes and biscuits.
• Grill- / Roasting pan
To bake and roast or as pan to collect fat.
5
Before first use
Warning! Refer to the Safety chapters.
Initial cleaning
• Remove all accessories and removable shelf
supports (if applicable).
• Clean the appliance before first use.
Important! Refer to the chapter "Care and
cleaning".
Setting and changing the time
You must set the time before you operate
the oven.
When you connect the oven to the electrical
supply or after a power cut, the symbol
flashes.
Press the + or - button to set the correct time.
After approximately 5 seconds, the flashing
stops and the display shows the time of day
you set.
Preheating
Preheat the empty appliance to burn off the remaining grease.
1. Set the function
and the maximum
temperature.
2. Let the appliance operate for 45 minutes.
3. Set the function
and the maximum
temperature.
4. Let the appliance operate for 15 minutes.
Accessories can become hotter than usually.
The appliance can emit an odour and smoke.
This is normal. Make sure that the airflow is sufficient.
Changing the time
1. Press
again and again until the symbol
flashes.
2. Press the + or - button to set the correct
time.
2
1
Daily use
Warning! Refer to the Safety chapters.
Display
1
2
3
1 Cooking function
2 Temperature
3 Time
6
www.zanussi.com
Button
Function
Description
On / off
To activate or deactivate the appliance.
Selection
To set an oven function.
Fast Heat Up
To activate the Fast Heat Up function.
Pyrolysis
To start the pyrolytic cleaning.
Clock
To set a clock function.
Minus, plus
/
To set the time and temperature.
Setting an oven function
3.
To change the temperature, press + or -.
Changing the temperature
To change the temperature when the appliance
operates:
1. Press the button
. The symbol ° flashes.
1
1.
2.
2. Press the button + or - to change the temperature.
2
Activate the appliance.
again and again until the symbol
Press
for the necessary oven function flashes.
The display shows the default temperature.
If you do not change the temperature in approximately five seconds, the appliance
starts to operate.
When you set an oven function, the temperature symbol flashes. The symbol
shows that the temperature in the appliance increases.
When the appliance is at the set temperature,
an acoustic signal sounds and the temperature
symbol stops flashing.
Oven functions
Oven Function
Application
Light
To activate the oven lamp without a cooking function.
True Fan Cooking
To roast or roast and bake food with the same cooking temperature, on more than one shelf, without flavour transference.
Conventional Cooking
To bake and roast on one oven level. The top and bottom heating elements operate at the same time.
Grilling
To grill flat food items in the middle of the shelf. To make toast.
Turbo Grilling
To cook large pieces of meat. The grill element and the oven fan
operate one after the other and circulate hot air around the food.
Pizza Setting
To make pizza, quiche or pie.
www.zanussi.com
7
Oven Function
Application
Fast Grilling
To grill flat food items in large quantities. To make toast. The full
grill element operates.
Bottom Heat
To bake cakes with crispy or crusty bottom. Only the bottom
heating element operates.
Meat
To roast meat. The top and bottom heating elements operate at
the same time.
Keep Warm
To keep the food warm.
Defrost
To thaw frozen food. Suitable for defrosting delicate food, e.g.
cream-filled gateaux, iced cakes, pastries, bread and other food
made of yeast dough.
Pyrolysis
To clean the oven. The high temperature burns off the residual
dirt. You can then remove it with a cloth when the appliance is
cold.
Residual heat function
With the Duration
function, the oven deactivates automatically some minutes before the
time period ends. The oven uses the residual
heat to complete the cooking without energy
consumption.
1.
Set an oven function. If necessary, change
the temperature.
2.
. The display shows
Press the button
FHU. The Fast Heat Up function starts to
operate.
3.
When the Fast Heat Up function is completed, an acoustic signal sounds. FHU
goes out. The set oven function continues
to operate.
Put the food in the oven.
Important! The residual heat function is
is more than
applicable only if the Duration
20 minutes.
Fast Heat Up function
With the Fast Heat Up function you decrease
the preheating time. You can use it with each
oven function except Keep Warm and Defrost.
The Fast Heat Up function works only if the
necessary temperature is 100 °C higher than
the current temperature in the oven.
Important! Do not put the food into the oven
until the Fast Heat Up function is completed.
4.
Clock functions
Clock function
Time of day
Minute Minder
Duration
8
Application
To set, change or check the time of day.
To set a countdown time. This function has no effect on the operation of
the oven.
To set how long the appliance must operate.
www.zanussi.com
Clock function
End
Application
To set when the appliance must be deactivated.
You can use Duration
and End
at
the same time to set the time when the appliance must be activated and then deactivated.
, then End
.
First set Duration
3.
Setting the clock functions
Press + or - to set the necessary clock
function.
The display shows the symbol for the clock
function you set. When the set time ends,
the symbol flashes and an acoustic signal
sounds for two minutes.
With the Duration
and End
functions, the appliance deactivates automatically.
2
1
1.
and End
, set an oven
For Duration
function and temperature. This is not nec. Refer to
essary for the Minute Minder
"Setting an oven function".
2.
again and again until the symbol
Press
for the necessary clock function flashes.
4.
5.
Press a button to stop the signal.
Deactivate the appliance.
Cancelling the clock functions
1. Press
again and again until the symbol
for the necessary clock function and
flash in the display.
2. Press and hold the button - until the clock
function goes out.
Additional functions
Child Lock
When the Child Lock is on you cannot operate the appliance. The oven door blocks
when the Child Lock is activated.
Activating the Child Lock
1. Press
to deactivate the appliance.
2.
and - at the same time, until the
Press
display shows SAFE. The Child Lock is on.
Deactivating the Child Lock
To deactivate the Child Lock, do the same
steps again.
Button sound
Deactivating the control beep
1. Press
to deactivate the appliance.
2.
and + at the
Press and hold the buttons
same time for approximately 2 seconds,
until an acoustic signal sounds.
www.zanussi.com
The control beep is deactivated.
Activating the control beep
To activate the control beep, do the same steps
again.
It is not possible to deactivate the sound
of the ON / OFF button.
Automatic switch-off
For safety reasons the appliance deactivates
after some time:
• If an oven function operates.
• If you do not change the oven temperature.
Oven temperature
Switch-off time
30 - 115 °C
12.0 h
120 - 195 °C
8.5 h
200 - 245 °C
5.5 h
250 - maximum °C
3.0 h
9
After an automatic switch-off, deactivate the
appliance fully. Then you can activate it again.
Important! The automatic switch-off
deactivates if you set the Duration or End
function.
Error code
If some parameters are not correct, the control
unit stops the functions which operate and the
display shows the related error code. Refer to
the chapter "What to do if".
the appliance cool. If you deactivate the appliance, the cooling fan continues to operate until
the temperature in the appliance cools down.
Safety thermostat
Incorrect operation of the appliance or defective components can cause dangerous overheating. To prevent this, the oven has a safety
thermostat which interrupts the power supply.
The oven activates again automatically when
the temperature drops.
Cooling fan
When the appliance operates, the cooling fan
activates automatically to keep the surfaces of
Helpful hints and tips
• The appliance has five shelf levels. Count the
shelf levels from the bottom of the appliance
floor.
• The appliance has a special system which
circulates the air and constantly recycles the
steam. With this system you can cook in a
steamy environment and keep the food soft
inside and crusty outside. It decreases the
cooking time and energy consumption to a
minimum.
• Moisture can condense in the appliance or
on the door glass panels. This is normal. Always stand back from the appliance when
you open the appliance door while cooking.
To decrease the condensation, operate the
appliance for 10 minutes before cooking.
• Clean the moisture after each use of the appliance.
• Do not put the objects directly on the appliance floor and do not put aluminium foil on
the components when you cook. This can
change the baking results and cause damage to the enamel.
• If you use two baking trays at the same time,
keep one empty level between them.
Cooking meat and fish
• Use a deep pan for very fatty food to prevent
the oven from stains that can be permanent.
• Leave the meat for approximately 15 minutes
before carving so that the juice does not
seep out.
• To prevent too much smoke in the oven during roasting, add some water into the deep
pan. To prevent the smoke condensation,
add water each time after it dries up.
Cooking times
Cooking times depend on the type of food, its
consistency, and volume.
Initially, monitor the performance when you
cook. Find the best settings (heat setting, cooking time, etc.) for your cookware, recipes and
quantities when you use this appliance.
Baking cakes
• Do not open the oven door before 3/4 of the
set cooking time is up.
Baking and roasting table
CAKES
10
www.zanussi.com
Conventional Cooking
True Fan Cooking
Cooking
time [min]
Notes
160
45 - 60
In a cake mould
160
20 - 30
In a cake mould
2
165
80 - 100
In a 26 cm cake
mould
170
2 (left and
right)
160
80 - 100
In two 20 cm cake
moulds on a wire
shelf1)
3
175
2
150
60 - 80
In a baking tray
Jam-tart
2
170
2 (left and
right)
165
30 - 40
In a 26 cm cake
mould
Sponge cake
2
170
2
150
40 - 50
In a 26 cm cake
mould
Christmas cake /
Rich fruit cake
2
160
2
150
90 - 120
In a 20 cm cake
mould1)
Plum cake
1
175
2
160
50 - 60
In a bread tin1)
Small cakes one level
3
170
3
150 160
20 - 30
In a baking tray1)
Small cakes two levels
-
-
2 and 4
140 150
25 - 35
In a baking tray1)
Small cakes three levels
-
-
1, 3 and 5
140 150
30 - 45
In a baking tray1)
Biscuits / pastry
stripes - one level
3
140
3
140 150
25 - 45
In a baking tray
Biscuits / pastry
stripes - two levels
-
-
2 and 4
140 150
35 - 40
In a baking tray
Biscuits / pastry
stripes - three
levels
-
-
1, 3 and 5
140 150
35 - 45
In a baking tray
Meringues - one
level
3
120
3
120
80 - 100
In a baking tray
Meringues - two
levels
-
-
2 and 4
120
80 - 100
In a baking tray1)
Buns
3
190
3
190
12 - 20
In a baking tray1)
Eclairs - one level
3
190
3
170
25 - 35
In a baking tray
Eclairs - two levels
-
-
2 and 4
170
35 - 45
In a baking tray
TYPE OF DISH
Shelf position
Temp
[°C]
Shelf position
Temp
[°C]
Whisked recipes
2
170
3 (2 and 4)
Shortbread
dough
2
170
3 (2 and 4)
Buttermilk
cheesecake
1
170
Apple cake (Apple pie)
2
Strudel
www.zanussi.com
11
TYPE OF DISH
Conventional Cooking
True Fan Cooking
Cooking
time [min]
Notes
Shelf position
Temp
[°C]
Shelf position
Temp
[°C]
Plate tarts
2
180
2
170
45 - 70
In a 20 cm cake
mould
Rich fruit cake
1
160
2
150
110 - 120
In a 24 cm cake
mould
Victoria sandwich
1
170
2
160
30 - 50
In a 20 cm cake
mould1)
1) Preheat for 10 minutes.
BREAD AND PIZZA
TYPE OF DISH
Conventional Cooking
True Fan Cooking
Cooking
time [min]
Notes
Shelf position
Temp
[°C]
Shelf position
Temp
[°C]
White bread
1
190
1
190
60 - 70
Rye bread
1
190
1
180
30 - 45
In a bread tin
Bread rolls
2
190
2 (2 and 4)
180
25 - 40
6 - 8 rolls in a baking tray1)
Pizza
1
230 250
1
230 250
10 - 20
In a baking tray or a
deep pan1)
Scones
3
200
3
190
10 - 20
In a baking tray1)
Cooking
time [min]
Notes
1 - 2 pieces, 500
gr per piece1)
1) Preheat for 10 minutes.
FLANS
TYPE OF DISH
Conventional Cooking
True Fan Cooking
Shelf position
Temp
[°C]
Shelf position
Temp
[°C]
Pasta flan
2
200
2
180
40 - 50
In a mould
Vegetable flan
2
200
2
175
45 - 60
In a mould
Quiches
1
180
1
180
50 - 60
In a mould1)
Lasagne
2
180 190
2
180 190
25 - 40
In a mould1)
Cannelloni
2
180 190
2
180 190
25 - 40
In a mould1)
1) Preheat for 10 minutes.
MEAT
12
www.zanussi.com
Conventional Cooking
True Fan Cooking
Cooking
time [min]
Notes
190
50 - 70
On a wire shelf
180
90 - 120
On a wire shelf
2
175
90 - 120
On a wire shelf
2
200
50 - 60
On a wire shelf
210
2
200
60 - 70
On a wire shelf
2
210
2
200
70 - 75
On a wire shelf
Shoulder of pork
2
180
2
170
120 - 150
With rind
Shin of pork
2
180
2
160
100 - 120
2 pieces
Lamb
2
190
2
175
110 - 130
Leg
Chicken
2
220
2
200
70 - 85
Whole
Turkey
2
180
2
160
210 - 240
Whole
Duck
2
175
2
220
120 - 150
Whole
Goose
2
175
1
160
150 - 200
Whole
Rabbit
2
190
2
175
60 - 80
Cut in pieces
Hare
2
190
2
175
150 - 200
Cut in pieces
Pheasant
2
190
2
175
90 - 120
Whole
Cooking
time [min]
Notes
TYPE OF DISH
Shelf position
Temp
[°C]
Shelf position
Temp
[°C]
Beef
2
200
2
Pork
2
180
2
Veal
2
190
English roast
beef, rare
2
210
English roast
beef, medium
2
English roast
beef, well done
FISH
TYPE OF DISH
Conventional Cooking
True Fan Cooking
Shelf position
Temp
[°C]
Shelf position
Temp
[°C]
Trout / Sea
bream
2
190
2
175
40 - 55
3 - 4 fish
Tuna fish / Salmon
2
190
2
175
35 - 60
4 - 6 fillets
Grilling
Preheat the empty oven for 10 minutes,
before cooking.
Quantity
TYPE OF DISH
Fillet steaks
www.zanussi.com
Grilling
Cooking time [min]
Pieces
[g]
Shelf position
Temp [°C]
1st side
2nd side
4
800
4
max.
12 - 15
12 - 14
13
Quantity
TYPE OF DISH
Grilling
Cooking time [min]
Pieces
[g]
Shelf position
Temp [°C]
1st side
2nd side
Beef steaks
4
600
4
max.
10 - 12
6-8
Sausages
8
-
4
max.
12 - 15
10 - 12
Pork chops
4
600
4
max.
12 - 16
12 - 14
Chicken (cut in 2)
2
1000
4
max.
30 - 35
25 - 30
Kebabs
4
-
4
max.
10 - 15
10 - 12
Breast of chicken
4
400
4
max.
12 - 15
12 - 14
Hamburger
6
600
4
max.
20 - 30
-
Fish fillet
4
400
4
max.
12 - 14
10 - 12
Toasted sandwiches
4-6
-
4
max.
5-7
-
Toast
4-6
-
4
max.
2-4
2-3
Turbo Grilling
Beef
TYPE OF DISH
Quantity
Shelf position
Temperature
[°C]
Time [min]
Roast beef or fillet, rare
per cm of thickness
1
190 - 200 1)
5-6
Roast beef or fillet, medium
per cm of thickness
1
180 - 190 1)
6-8
Roast beef or fillet, well
done
per cm of thickness
1
170 - 180 1)
8 - 10
TYPE OF DISH
Quantity
Shelf position
Temperature
[°C]
Time [min]
Shoulder, neck, ham
joint
1 - 1.5 kg
1
160 - 180
90 - 120
1) Preheat the oven.
Pork
Chop, spare rib
1 - 1.5 kg
1
170 - 180
60 - 90
Meat loaf
750 g - 1 kg
1
160 - 170
50 - 60
Pork knuckle (precooked)
750 g - 1 kg
1
150 - 170
90 - 120
Veal
TYPE OF DISH
Roast veal
Knuckle of veal
14
Quantity
Shelf position
Temperature [°C]
Time [min]
1 kg
1
160 - 180
90 - 120
1.5 - 2 kg
1
160 - 180
120 - 150
www.zanussi.com
Lamb
TYPE OF DISH
Quantity
Shelf position
Temperature [°C]
Time [min]
Leg of lamb, roast
lamb
1 - 1.5 kg
1
150 - 170
100 - 120
Saddle of lamb
1 - 1.5 kg
1
160 - 180
40 - 60
Poultry
Quantity
Shelf position
Temperature [°C]
Time [min]
Poultry portions
TYPE OF DISH
200 - 250 g each
1
200 - 220
30 - 50
Chicken , half
400 - 500 g each
1
190 - 210
35 - 50
Chicken, poulard
1 - 1.5 kg
1
190 - 210
50 - 70
Duck
1.5 - 2 kg
1
180 - 200
80 - 100
Goose
3.5 - 5 kg
1
160 - 180
120 - 180
Turkey
2.5 - 3.5 kg
1
160 - 180
120 - 150
Turkey
4 - 6 kg
1
140 - 160
150 - 240
Quantity
Shelf position
Temperature [°C]
Time [min]
1 - 1.5 kg
1
210 - 220
40 - 60
Fish (steamed)
TYPE OF DISH
Whole fish
Defrosting
[g]
Defrosting
time [min]
Further defrosting
time [min]
Notes
Chicken
1000
100 - 140
20 - 30
Place the chicken on an upturned saucer placed on a
large plate. Turn halfway
through.
Meat
1000
100 - 140
20 - 30
Turn halfway through.
Meat
500
90 - 120
20 - 30
Turn halfway through.
Trout
150
25 - 35
10 - 15
-
Strawberries
300
30 - 40
10 - 20
-
Butter
250
30 - 40
10 - 15
-
TYPE OF DISH
Cream
2 x 200
80 - 100
10 - 15
Cream can also be whipped
when still slightly frozen in places.
Gateau
1400
60
60
-
Drying - True Fan Cooking
Cover the oven shelves with baking parchment.
www.zanussi.com
15
VEGETABLES
TYPE OF DISH
Shelf position
Temperature [°C]
Time [hr]
1/4
60 - 70
6-8
3
1/4
60 - 70
5-6
3
1/4
60 - 70
5-6
Mushrooms
3
1/4
50 - 60
6-8
Herbs
3
1/4
40 - 50
2-3
Temperature [°C]
Time [hr]
1 level
2 levels
Beans
3
Peppers
Vegetables for
soup
FRUIT
TYPE OF DISH
Shelf position
1 level
2 levels
Plums
3
1/4
60 - 70
8 - 10
Apricots
3
1/4
60 - 70
8 - 10
Apple slices
3
1/4
60 - 70
6-8
Pears
3
1/4
60 - 70
6-9
Care and cleaning
Warning! Refer to the Safety chapters.
• Clean the front of the appliance with a soft
cloth with warm water and a cleaning agent.
• To clean metal surfaces use a usual cleaning
agent.
• Clean the oven interior after each use. Then
you can remove dirt more easily and it does
not burn on.
• Clean stubborn dirt with a special oven
cleaner.
• Clean all oven accessories after each use
and let them dry. Use a soft cloth with warm
water and a cleaning agent.
• If you have nonstick accessories, do not
clean them using aggressive agents, sharpedged objects or a dishwasher. It can destroy nonstick coating.
Stainless steel or aluminium appliances:
Clean the oven door with a wet sponge only.
Dry it with a soft cloth.
16
Do not use steel wool, acids or abrasive materials, as they can cause damage to the oven surface. Clean the oven control panel with the
same precautions.
Shelf supports
You can remove the shelf supports to clean the
side walls.
Removing the shelf supports
2
1
1 Pull the front of
the shelf support
away from the side
wall.
2 Pull the rear end
of the shelf support
away from the side
wall and remove it.
www.zanussi.com
Installing the shelf supports
Install the shelf supports in the opposite sequence.
The rounded ends of the shelf supports
must point to the front.
Pyrolysis
appliance increases. The symbol
flashes.
After some minutes the door locks. The
.
display shows the symbol
When the Pyrolysis is completed, the display
shows the time of day. The oven door stays
locked. When the appliance is cool again, an
acoustic signal sounds and the door unlocks.
Warning! The appliance becomes very
hot. There is a risk of burns.
Caution! If a hob is installed with the
appliance, do not use it at the same times
as the Pyrolysis function. It can cause damage
to the appliance.
1.
Remove the removable shelf supports (if
applicable) and accessories from the appliance. Refer to "Removing the shelf supports".
Caution! Do not let the removable shelf
supports stay in the appliance during the
Pyrolysis. There is a risk of damage.
2.
3.
Remove the worst dirt manually.
Fully close the oven door.
The cleaning procedure cannot start if you
do not close the oven door.
4.
5.
6.
again and again until the display
Press
.
shows
– The display shows P1 and
one after
the other.
– An acoustic signal sounds as a reminder
to remove all accessories and shelf supports from the oven.
– The clock display shows 1:30.
– Duration
flashes.
flashes, press + or - to set the
When
necessary procedure:
• P1 - if the oven is not very dirty. The procedure is 1 h 30 min long.
• P2 - if the oven is more dirty. The procedure is 2 h 30 min long.
to start the procedure.
Press
The bars on the symbol come on one by
one to show that the temperature in the
www.zanussi.com
To stop the Pyrolysis before it is comple.
ted, press
Setting the end time for the Pyrolysis
1.
2.
3.
You can use the End
function to delay
the start of the procedure.
Start the Pyrolysis procedure.
again and again until the symbol
Press
flashes. The display shows the time for
the end of the Pyrolysis.
Press + or - to adjust the time for the end
of the Pyrolysis.
Oven lamp
Warning! Be careful when you change
the oven lamp. There is a risk of electrical
shock.
Before you change the oven lamp:
• Deactivate the oven.
• Remove the fuses in the fuse box or deactivate the circuit breaker.
Put a cloth on the bottom of the oven to
prevent damage to the oven light and
glass cover.
Always hold the halogen lamp with a cloth to
prevent grease residue from burning on the
lamp.
1.
2.
3.
4.
Turn the glass cover counterclockwise to
remove it.
Clean the glass cover.
Replace the oven light bulb with an applicable 300 °C heat-resistant oven light
bulb.
Use the same oven lamp type.
Install the glass cover.
17
Cleaning the oven door
The oven door has four glass panels. You can
remove the oven door and the internal glass
panels to clean them.
90°
The oven door can close if you try to remove the glass panels before you remove
the oven door.
Caution! Do not use the appliance
without the glass panels.
Removing the oven door and the glass
panels
5 Release the locking system to remove
the glass panels.
1
1 Open the door
fully and hold the two
door hinges.
2 Lift and turn the
levers on the two
hinges.
6 Turn the two fasteners by 90° and remove them from their
seats.
2
7 Carefully lift (step
1) and remove (step
2) the glass panels
one by one. Start
from the top panel.
Clean the glass panels with water and soap.
Dry the glass panels carefully.
Installing the door and the glass panels
3 Close the oven
4 Put the door on a
door to the first open- soft cloth on a stable
ing position (halfway). surface.
Then pull forward and
remove the door from
its seat.
18
When the cleaning is completed, install the
glass panels and the oven door. Do the above
steps in the opposite sequence.
www.zanussi.com
3
1 2
Make sure that you put the glass panels (1, 2
and 3) back in the correct sequence. The middle panel (2) has a decorative frame. The
screen-printing zone must face the inner side
of the door. Make sure that after the installation
the surface of the glass panel frame (2) on the
screen-printing zones is not rough when you
touch it.
Make sure that you install the top panel in the
seats correctly.
What to do if…
Warning! Refer to the Safety chapters.
Problem
Possible cause
Remedy
The oven does not heat up.
The appliance is deactivated.
Activate the appliance.
The oven does not heat up.
The clock is not set.
Set the clock.
The oven does not heat up.
The necessary settings are not
set.
Make sure that the settings are correct.
The oven does not heat up.
The automatic switch-off is on.
Refer to "Automatic switch-off".
The oven does not heat up.
The Child Lock is on.
Refer to "Deactivating the Child Lock".
The oven does not heat up.
The fuse in the fuse box is released.
Do a check of the fuse. If the fuse is
released more than one time, contact
a qualified electrician.
The oven lamp does not operate.
The oven lamp is defective.
Replace the oven lamp.
The oven does not heat up.
The fan does not operate. The
display shows
or
.
The demo mode is activated.
1.
2.
Deactivate the appliance.
3.
Press and hold the buttons
and
at the same time until the
acoustic signal sounds again and
the indicator goes out.
www.zanussi.com
Press and hold the button
for
approximately two seconds. An
acoustic signal sounds.
19
Problem
Possible cause
The display shows an error
code.
Remedy
There is an electronic fault.
1.
2.
Deactivate the appliance with the
house fuse or the safety switch in
the fuse box and activate it again.
If the display shows the error
code again, contact the service
centre.
It takes too long to cook the
dishes, or they cook too quickly.
The temperature is too low or too
high.
• Adjust the temperature if necessary.
• Follow the advice in the manual.
Steam and condensation collect on the food and in the
oven.
You left the dish in the oven for
too long.
Do not keep the dishes in the appliance for longer than 15 - 20 minutes
after the cooking ends.
If you cannot find a solution to the problem
yourself, contact your dealer or the service centre.
The necessary data for the service centre is on
the rating plate. The rating plate is on the front
frame of the appliance cavity.
We recommend that you write the data here:
Model (MOD.)
.........................................
Product number (PNC)
.........................................
Serial number (S.N.)
.........................................
Installation
Warning! Refer to the Safety chapters.
Building In
548
558
20
min. 550
590
573
20
min. 560
589
594
5
20
www.zanussi.com
Electrical installation
Warning! Only a qualified person must do
the electrical installation.
600
The manufacturer is not responsible if you
do not follow the safety precautions from
the chapter "Safety Information".
min. 550
20
This appliance is supplied with a main plug and
a main cable.
min. 560
Cable
Cable types applicable for installation or replacement: H07 RN-F, H05 RN-F, H05 RRF,
H05 VV-F, H05 V2V2-F (T90), H05 BB-F.
For the section of the cable refer to the total
power (on the rating plate) and to the table:
Total power
A
B
Section of the cable
maximum 1380 W
3 x 0.75 mm²
maximum 2300 W
3 x 1 mm²
maximum 3680 W
3 x 1.5 mm²
The earth cord (green / yellow cable) must be 2
cm longer than phase and neutral cables (blue
and brown cables).
Environment concerns
The symbol on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
www.zanussi.com
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
21
Packaging material
The packaging material is environmentallyfriendly and recyclable. Plastic parts are marked
22
with international abbreviations such as PE, PS,
etc. Dispose of the packaging material in the
containers provided for this purpose at your local waste management facility.
www.zanussi.com
www.zanussi.com
23
397286201-B-032013
www.zanussi.com/shop
Download PDF

advertising