Electrolux EBE1200 User manual

Electrolux EBE1200 User manual
English
MOBILE SPLIT AIR CONDITIONER
ELECTRONIC
[J CONTENTS
Introduction ........... ae PE 1
Technical Specifications ................. E EEK KKKKKEE 2
Description oii ee 3
Installation ore rreco. 4
Installation of Outdoor UNit .............e o eeceoncorcecccrareoorarecere rarveíe. 4
Electrical Connection ...........eoee.conrcorceoccroverecareercrrer rene о 6
Operation .................—e_e._e.ererererecererrrreererrerrericer cree 7
Use of Wireless Remote Control .................. iii, 9
On-unit Indicators and Controls ..................—_—e—__e_eeeerreeeescenecoo 10
Remote Control......................000000000 00e sa aa ae eee a eee ana eee 0 11
Operation Procedure ......................020000000e 0 sance ac a ane aa nee nes 12
Tuming on the Air Conditioner.................0100 00000 nee eee a ses ses 00006 12
Fan Operation ............000200000 00040 eee ee sa 0 ses sea aa ee aa sea en 010000 12
Cooling Operation .............0..000000000 00 00e aa sea ea ea an eat Tes 000005 12
Cooling Operation With Auto Fan Mode .............0.0000000 5000 a caca na ac 0006 12
Dry Operation ............e_eereeoerseecorvecrecenerorariocerrereorecec. 13
Selecting the Temperature ...............r—rreorerevsaccvareceoererrr eee. 13
| FEEL Function ...........—.es_.onercormeverararecorenraer ee. RAA 13
Timer Operation ...............000000000 00 eee ee 0000 can ae see ne 1e a TA 100006 13
Timer Operating Modes ................200000 00000 a 00000000 seed 0 0000000 14
Sleep Function ...........ec_eeeeeoerserreroverererevecarrererereero rte. 15
Room Temperature Display ..............ecoerrrecsrecccooracarervecaca rene. 15
Current Clock Time Set ........coeeocorcceerececrerooccacreroerrerrvacerere. 15
Lock Mode Function ..........o _.eeeereeecorooreroredorrercernerrerecererer 16
Tuming Off the Air Conditioner ...........e.-..—eeeeecserrereerrrerer rene. 16
On-unit Operation ............_eoeereceeccccorerecarrraacrrr area ren ree. 16
Precautions ..................eeceeerececerscoervresrerrerserrrcnecer acer. 17
Care and Maintenance ....................eoencccrrerreareecec rre cane: 17
Moving and STONING... RE 18
Before Calling For Service ............... iii 19
[} INTRODUCTION
. This new split mobile air conditioner consists of an indoor and outdoor unit, interconnected
o by a flexible hose. The indoor unit is equipped with four castors for easy mobility.
|
|
The air conditioner you have purchased is factory-charged and ready for use. No special
installation is required; just follow the simple instructions and enjoy this fully featured,
versatile air conditioner.
| The electronic model gives the user the choice of local or remote control operation, precise
| temperature setting and control, timer operation and a built-in protection system for
trouble-free and energy-efficient operation.
PLEASE READ THESE INSTRUCTIONS
BEFORE OPERATING THE AIR CONDITIONER
WARNING:
* This air conditioner must be grounded to protect against electrical shocks.
* Electrical connections and power cord replacement should be done only by an authorized
electrician and in accordance with electrical regulations and local codes.
* Do not expose the indoor unit to rain.
IMPORTANT NOTES:
When using this air conditioner for the first time, please do the following:
1. Read the instruction manual and familiarize yourself with the controls.
Plug the electric cord into a power socket, protected by the proper fuse.
Check that all control functions operate properly, using the remote controller.
Repeat step 3 when the remote control unit is in its compartment.
oh LW
Disconnect the electrical cord from the power socket, wait 3 minutes and reconnect the
unit.
English 1
tate
[|
English 2
TECHNICAL SPECIFICATIONS
Cooling capacity (I) W / Btu/hr 3100 / 10600
Power consumption wo 1300
Dehumidification | Uhr 1.6
Air delivery m°/hr / CFM 370 / 220
Indoor fan speeds | | 3 + Auto
Connecting tube length mm 1900
Electrical supply V/Ph/Hz 220-240/1/50
Fuse rating amp 15 (delayed action)
Dimensions, indoor unit (HxWxD) mm 603x470x341
Dimensions, outdoor unit (HxWxD) mm 490x440x188
Weight: indoor / outdoor unit Kg 40 / 10
(1) Capacity based on test conditions of:
Indoor: 27°C/80°F DB - 19°C/67°F WB
Outdoor: 35°C/95°F DB - 24°C/72°F WB
In accordance with: ISO / DIS 5151.2
Actual cooling capacity might vary according to local
environmental conditions.
Optimal operation temperature:
Indoor: 21-34*C/70-93*F.
Outdoor: 20-42°C/68-108°F.
о 0 мо сы о ю =
— —
-—-
N
>
[] DESCRIPTION
Figure 1
interconnecting hose
Indicators and controls
Adjustable supply air grille
Castors
Service cover
Carrying handle - indoor uni
Carrying handle - outdoor unit
Attaching pins
Condenser fan grille
. Condensate overflow outlet
. Water basin
Remote control compartment
Figure 2
| 12. Air filter handle
13.
14.
15.
16.
17.
Return air intake
interconnecting hose
Power cord
Keyholes
Drain tube with plug
Figure 3
18.
19.
Remote control
suction pad
7
\
10) (9) (17)
Figure 1. Indoor á Outdoor Unit Component Description
Figure 3. Accessories
English 3
L] INSTALLATION
English 4
This mobile split air conditioner can be installed by the customer, as follows:
Choose an appropriate place for the air conditioner indoor unit near an exterior opening
(window or door). A grounded 15-amps/220-V electrical outlet should be within 2.5 meters
of the indoor unit.
Determine whether the outdoor unit is to be suspended from the window or the wall, or
placed on the floor near a doorway. Be sure the outdoor unit is stable and well supported
at its place of installation (see Figure 4).
The outdoor unit must be installed with the rear grille facing the wall at a minimum distance
of 100 mm.
Be sure the outdoor unit is set so that its handle and hose are on top. To assure proper
condensate drainage, make sure the unit is installed in a leveled position.
In high humidity conditions, the outdoor unit condensate basin (6) may overflow. If
condensate leak occurs, it is recommended to use a permanent drain tube. Remove plug
(7 see Figure 4), located under the unit, and fit instead a 13-mm OD hose (8), routed to
a drainage point.
Indoor unit
Window
Outdoor unit, wall mounted
Outdoor unit, floor mounted
interconnecting hose
Condensate basin
Plug
‘Drain tube
NORA WON =
Figure 4. Installation
INSTALLATION OF OUTDOOR UNIT
A standard kit (Figure 7), supplied with the air conditioner for supporting the outdoor unit,
makes it possible to mount it either from a window sill (Figure 5) or on the wall (Figure 6).
1. Siip the unit handle over the sliding bracket (2)(Figure 7) of the unit support (see Figures
5 ando).
2. For window mounting, refer to figure 5. Place the fixed support (3) (Figure 7) on the win-
dow frame, drill three holes in the window frame and mount the support securely with
three screws.
3. Place the sliding bracket (2) so that its slots (4) fit into the matching studs (6) in the fixed
support (3). Secure sliding bracket with wing nuts (5) (Figure 7). Suspend the outdoor
unit on the sliding bracket.
4. Slide the unit to the most suitable place (minimum 100 mm from wall) and tighten the two
wing nuts (5) (Figure 7).
>. Place the securing bracket (7) (Figure 7) in place and tighten it. Verify that the unit is well
supported, stable and secured.
м о ль ею
Sliding bracket
Fixed support
Slots
Wing nuts
Studs
Securing bracket
Figure 7. Outdoor unit supporting kit
English 5
6. For wall mounting, refer to Figure 6. Place fixed bracket (3) against wali, drill three holes
in the wall and fasten with three screws; verify that the support is level.
7. Engage the sliding bracket with the two holes over the two studs and tighten the wing
nuts (5). Install the securing bracket (7). Verify that the unit is well supported and stable.
8. Prepare a slot in the lower part of door or window frame for the interconnecting hose loc-
English 6
tion (see Figures 8, 9, 10, 11).
Pass the interconnecting hose which contains the refrigerant tubing, cable and drain tube
through a window or door opening. Be sure not to subject the interconnecting hose to any
over-stress, avoid sharp bends or forced twisting. Before operation, close the window or
door; use the suction pads if needed.
NOTE: !f the air conditioner is to be used periodically in alternate rooms, it is recommended
to cover the opening in the door or window. Additional mounting kits are available from your
local dealer.
When transporting the unit, make sure to keep it in vertical position (discharge grille on top).
Also, when removing outdoor unit, empty the water accumulated at the bottom by tilting to
one side.
Figure 8 Figure 9 Figure 10 Figure 11
ELECTRICAL CONNECTION
Before plugging in, please check that:
1. Socket and mains correspond to data given in specifications.
2. Plug fits the socket; if not, change socket.
3. Socketis properly grounded. The manufacturer is not responsible for any damage in-
curred due to failure of following normal safety procedures.
CUITS 7 e
ONE US
L] OPERATION
In order to obtain maximum comfort and economy, please make sure that:
* Doors and windows of room to be conditioned are closed.
* Air outlet and inlet openings on the unit are free of any obstruction.
* Shade the room from direct sun rays and avoid excessive heat sources in the room.
MODES OF OPERATION, FUNCTIONS AND FEATURES
0
+
COOL
Cools, dehumidifies and filters the room air. Maintains desired room temperature.
DRY
Dehumidifies and softly cools the room. In DRY Mode, the air conditioner operates atan
increased dehumidifying power. This function is recommended for use when
temperature is rather low but the humidity is high.
FAN
Recirculates and filters the room air. Maintains constant air movementin the room.
AUTO FAN
The air conditioner automatically selects the FAN speed in accordance with the room
temperature. At the start, the unit operates at high fan speed. As the room air
approaches the desired temperature, the fan switches to a lower speed, for quieter
operation.
| FEEL
Switches the temperature sensing point to the place where the remote controlis located
(generally the temperature sensor is located behind the intake grille of the air
conditioner). This function is designed to provide a personalized environment by
transmitting the temperature control command from the location next to you. The
communication between the Remote Control and the unit is done via infra-red signal.
Therefore, in using this function, the Remote Control should always be aimed, without
obstructions, atthe air conditioner.
TIMER
Real time contro! and display, automatically turns the air conditioner ON and OFF
according to the time of day setting, ensuring comfort conditions before returning home,
without wasting electricity; it turns off the air conditioner automatically when sleeping.
English 7
SLEEP
Designed to create comfortable sleeping conditions. When in COOLING mode, the
temperature rises one degree centigrade above the set point after each consecutive
hour, up to three hours, from the start of the mode. The temperature rise prevents the
feeling of over-cooling while sleeping (when your body is at rest). When in SLEEP
mode, the air conditioner will be automatically turned off after seven hours. The resultis
a more comfortable and invigorating sleep, which leaves you feeling fresh and
energetic in the morning.
ROOM TEMPERATURE
Measures and displays room temperature.
FILTER INDICATION
Filter indicator on the indoor unit display is turned on when the filter requires cleaning.
After cleaning and reinstalling the filter, the system should be reset.
E
BUZZER INDICATOR
A soft buzzer will sound atthe indoor unit display to indicate that a command sentby the
remote control has been accepted and stored in the unit's memory.
This feature may be easily canceled by the user from the display panel.
@
ON-UNIT OPERATION
The air conditioner can be turned on or off directiy from the indoor unit display panel
without the use of the remote control.
3-MIN. DELAYED RUN
The compressor is protected by a three-minute delayed restart.
MEMORY
The microprocessor retains the last data entry, whether or not the unit is plugged in.
Therefore, when the unit restarts after a power disruption or failure, it will resume
operation in the same mode as before the power disruption.
= г тих
а“ аа
LE FE
LOCK
Freezes the last operation setting on the remote control. When LOCK is activated, the
remote control will be unable to control the air conditioner.
English 8
[J USE OF WIRELESS REMOTE CONTROL
PRIOR TO OPERATION
(Refer to Figure 12)
| Prior to operating your air A
a conditioner, make sure that: ,
* The indoor unit is properly con-
+
же,
nected to the power supply
Indicator (A) on the unit's display
is lit, meaning that the air condi- uu
tioner is ready to accept your ``
remote control commands. > 7
* The red tab protecting the ^^--------
remote control battery has been
removed.
* For clock setting see page 15.
REMOTE CONTROL COM-
PARTMENT
| Use the remote control compart- ntrol lication
| ment when unit is not in use. Figure 12. Remote Control Applicatio
Remote control can be flipped in
or out of its compartment.
* Aim at the infrared signal receiver at the room air conditioner when operating.
The remote control signal can be received at a distance of up to 8 m.
Be sure that no obstructions exist between the remote control and the signal receptor.
Do not drop or throw the remote control unit.
* Do not place the remote control unit in a location exposed to direct sunlight, or next to a
heating unit, or any other heat source.
* Do not expose the air conditioner signal receiver (H) to a strong light such as fluorescent
lamp or sunlight.
English 9
[1 ON-UNIT INDICATORS AND CONTROLS (Refer to Figure 13)
English 10
STAND-BY INDICATOR
Lights up when the air condi-
tioner is connected to power
and ready to receive the
remote control commands.
OPERATION INDICATOR
Lights up during operation.
Blinks to announce that the
remote control infrared signal
has been received and stored.
Blinks continuously when com-
pressor operates in its high-
pressure protection mode.
. TIMER INDICATOR
Lights up during Timer and
Sieep operation.
FILTER & WATER OVER-
FLOW INDICATOR
Lights up when air filter
requires cleaning. Blinks dur-
ing water overflow .
COOLING INDICATOR
Lights up only when button (F)
is pressed.
COOL / ON / OFF - UNIT
OPERATION BUTTON
Used to switch the unit
to positions: ON, OFF, and
COOLING without the use of
the remote control.
. RESET/CANCEL BUTTON
Press to turn off the FILTER in-
dicator and to reset the filter
function, after the clean filter
has been reinstalied.
Press to cancel the buzzer an-
nouncer, if elected.
. SIGNAL RECEIVER
Receives signals from the
remote control.
na. El co
—
Figure 13. On-unit Indicators and Controls
[|] REMOTE CONTROL. (Refer to Figure 14)
EN START/STOP button
EEN Operation mode selection
button
JE FAN SPEED and AUTO FAN
button
ER Temperature set UP
button (+) =
EN Temperature set DOWN fo —
button (-) ASHES bd [2H
10:30* 12:00 10: 16 AM
K | FEEL temperature sensing a LH
button — 723 N
—— Y
SLEEP button > = S rad, A
N _7
EEN ROOM temperature button pu ира 5,
| CS)
I TIMER select button en ©
|
{td TIMER set button u в & 8 LL
co up (+) — FE) ED
|
6 66
TIMER SET button °
TIMER CLEAR bution
о
(6)—
EEE TIMER set down (-) button (+ | ня)
Om
DT
«
4
=
EEE LOCK button N
EE] LCD display
Figure 14. Remote Contro! Unit
ELY | FEEL sensor
Infrared signal transmitter
Transmission sign
English 11
Cee ae,
[1 OPERATION PROCEDURE (Refer to Figure 13 & 14)
TURNING ON THE AIR CONDITIONER
Press START/STOP button (1) to turn the air
conditioner on. Indicator (B) on the air ОА Délé
conditioner will light up, indicating that the LA A
unit is in operation. (1-17 вх
Note that the LCD operation display (15) wili % A
always show the last mode of operation and 3 "
the previous function used. ит |
= IEEE |
VENTILATING OPÉRATION
Select the FAN mode by pressing MODE r EII
button (2). Switch to the desired fan speed 5 + ® & |=
È (fa A rouen 11.51 АМ
by pressing FAN speed button (3). EC EEE hah AM
COOLING OPERATION
Select the COOLING mode by pressing REX on
MODE button (2). Switch to the desired fan AS + sé |
speed or to AUTO fan by pressing button rds" cdi TE
(3). Select suitable temperature setting.
E,
ПТ
COOLING OPERATION WITH AUTO
FAN MODE
This operation starts with the highest air flow
in order to quickly lower the room
temperature. It will then automatically switch
to the low air flow to quietly maintain the
selected temperature.
(AE = Sel:
A "Mp
dj ihe] RIO
© rss |U-Z4LE
ue 7 23e it
e
English 12
ro
DRY OPERATION
| Select the DRY mode by pressing MODE eG —
button (2). Select the suitable temperature Ex RO |2
| setting. While in DRY mode, the air 0" CEE TaD av
! conditioner will operate at low fan speed, Е © eu (TE Te
| regardiess of the fan setting on the LCD ue 8 aye AM
* operation display. The fan might stop — |
| operating from time to time to prevent = =
| over-cooling. `
SELECTING THE TEMPERATURE
Press temperature button (4) or (5) to , - en
change the temperature setting on the LCD AA We E
operation display (15). The temperature ac Em (II À:
setting is shown in degrees centigrade. A ON TOO FM HU
higher number indicates a higher room pue % A
temperature; a lower number indicates a | el a
lower room temperature.
| FEEL FUNCTION
Press | FEEL button (6) to activate the |
FEEL function. Thermometer sign and
temperature set-up will appear on the LCD
operation display (15). Select suitable AE Ge | A
| temperature setting. Make sure that the a TEA mn —
remote control unit is aimed at the air eo E db
conditioner, with the | FEEL sensor (16) in Е %
front. Prevent the | FEEL sensor from being = ei A
affected by heat sources such as lamps, =8 - 1
heaters, direct sun, etc., or from being ¡ — =>
directly affected by the air conditioner air
flow. These may cause the sensor to
transmit the wrong temperature data, thereby
disturbing of the | FEEL function.
TIMER OPERATION
| Press TIMER select button (9) to activate he (A. <a (2)
' timer operation mode. Each time the TIMER EI
button (9) is pressed, one of the following
four types of operation modes will appear on
the LCD display. The operation modes are
sequenced in the direction of arrow. Indicator
(C) on the air conditioner will light up during
TIMER operation.
£9
|
A ; + As
DIE ES
„”
NOTE: After power failure (when the unit is in TIMER mode) the unit will be turned
automatically to STAND BY mode and the timer operation will be cancelled. To resume the
timer operation follow the instructions above.
English 13
English 14
TIMER OPERATING MODES
1. TIMER ON ВЫ fl. TIMER OFF
a a
ON {CY OFF |
—
—
Al
T— PE
——
—
—
—
———
—
—
—
bebe
HE {HR (20e
"ON | ® OFF IRENA ES
PS
EM EN
ON [CJ OFF.
ii. TIMER ON AND OFF
<Q
|, TIMER ON
This mode enables you to set a starting operating time. Press the TIMER
button (9) til! the ON sign blinks. Starting time can be adjusted using the up
and down buttons (10) and (11), respectively. Press SET button (12) to acti-
vate the timer.
Example: Operation is restored at 10:30 AM.
1. TIMER OFF
This mode enables you to set the time at which timer stops
Press the timer button (9) twice, the OFF sign will blink. Time can be ad-
justed using the up and down buttons (10) and (11), respectively. Press
SET button (12) to activate the timer.
Example : Operation stops at 12:00 PM.
. TIMER ON AND OFF
This mode enables you to set the start and stop time of operation. Press the
TIMER button (9) till the OFF sign blinks, by pressing again the ON sign will
blink. Time can be adjusted by using the up and down buttons (10) and
(11), respectively. Press SET button (12) to activate the timer.
Example: Operation is restored at 10:30 AM and stops at 12:00 PM.
IV.CLEAR
Use this mode to cancel timer operation. Press CLEAR button (13), timer
operation will terminate and the LCD display will be cleared for each timer
mode. When CLEAR button is pressed timer indicator (C) will turn OFF.
NOTE: lf timer button (9) is selected and neither time adjust, SET, or CLEAR buttons are
pressed within 15 seconds, the timer operation will be canceled and the last set-up will be
displayed.
SLEEP FUNCTION
Press SLEEP button (7) to select the SLEEP Cu ==
function. When the sleep function is activated A x= A ё E =
the air conditioner will be automatically TU т (EEE AM
turned OFF after seven hours. If at the LON ASR OFT
same time TIMER OFF is activated, as well, ен a ии ° A
the air conditioner will be turned OFF S
according to the TIMER setting. Su =
To cancel the SLEEP function press one of
the following :
—* START/STOP button (1)
* SUEEP button (7)
ROOM TEMPERATURE DISPLAY
By pressing the ROOM temperature button
(8), the measured room temperature and the
room temperature sign will be displayed for 5
seconds. For permanent display of the room
temperature, hold ROOM Temperature button
(8) for at least 4 seconds before releasing it.
ny
1 om
[>
“IR
GA
pa
en
e
J
ET f
Coral ors
Sp Lf 216
y
x
PCR Al
‚x
>
Lit
СР
“on
wi, али"
+ =
a
а он i
1
Lal
Lot
EB:
]
i
I
| OT ;
”
To cancel the Room Temperature display,
press one of the following:
* Another pressing on room temperature button (8).
* Change of MODE button (2)
NOTE: Room temperature range is between 0°C and 36°C in 1°C increments. Display should
show "HI" or "LOW" fo represent temperature above 36°C or below 2°C.
CURRENT CLOCK TIME SET
Clock setting is performed when batteries are >= DE E
inserted. The remote contro! displays the = = =
setting and the clock display will blink 217 a |
"00:00" or "12:00 AM" (AM sign will blink НН РО
too) till a new time is set. For clock setting, = < de E
use buttons (10) (11) for setting the hours o | =>. E
and minutes, respectively, and then press |= Y
timer SET button (12). The clock setting can
also be performed by pressing timer SET
button (12) and timer CLEAR button 13) for
5 seconds. The clock display will blink; for a
new setting follow the steps described above.
English 15
Rr a
LOCK MODE FUNCTION
By pressing lock button (14) the remote
control will lock the last operation setting. AN
function buttons will be inoperative including
START/STOP bution. By pressing lock button
(14) again, the remote control will be
released from its locked mode. When lock
mode is functioning, the transmission sign
(18) will be on.
AX: Qed]
ENT DG
MEE
TURNING OFF THE AIR CONDITIONER
Press START/STOP button (1) to turn OFF
the air conditioner. indicator (B ) on the air
conditioner will be turned off. Indicator (A)
will stay lit, indicating that the air conditioner
is in STAND-BY mode and ready to accept
any new command from the remote control.
The remote control LCD will display the
clock time and room temperature. The last
operating set-up will be kept for the next
operation.
ON-UNIT OPERATION
If the remote control cannot be operated, the
air conditioner can be turned on for cooling
or completely turned off, by pressing MODE
button (F) on the air conditioner. Indicator
(E) will light up to indicate if the air
conditioner operates in cooling
English 16
[1 PRECAUTIONS
* This air conditioner has been manufactured for domestic environments and should not be
used for any other purpose.
| * Do not obstruct the air discharge and inlet of the air conditioner.
* If repair is needed, contact only the nearest authorized service center; do not consider
unauthorized service.
* This air conditioner is to be used by adults only. Do not allow children to play with it.
* Always ground the unit.
* Make sure the unit is installed in a levelled position.
* Before cleaning or performing any maintenance operations, always disconnect the electric
power supply plug from the socket.
* Do not place any strain on the power cord when moving the unit.
* The air conditioner should not be installed at a place having any combustible gases, oil or
sulphur in the atmosphere, or near any possible sources of heat.
* Do not place hot or heavy objects on the air conditioner.
* Clean air filter periodically.
* The air conditioner should be transported in an upright position. After transporting, wait at
least one hour before turning the unit on.
* Move the unit with caution over carpets and rugs.
* Incase of damage to the power cord, it should be replaced or repaired only by an authorized
technician.
* This unit conforms to EEC Directive of Electromagnetic compatibility (89/336/EEC)
[1 CARE AND MAINTENANCE
WARNING:
Before performing any maintenance procedure, make sure to disconnect the air conditioner
from the power supply.
CLEANING THE AIR FILTER (See Figure 2)
The filter is located at the back of the indoor unit. Slide the filter up, pulling on the filter
handle (12). Rinse the filter with tap water, dry it and re-install it in place. Clean at least
once during the season, or as necessary.
DO NOT OPERATE THE UNIT WITHOUT FILTERS!
CLEANING OUTDOOR UNIT CONDENSATE BASIN (see Figure 15)
Remove the water basin (2) by unscrewing the four screws (3) on each side of the basin.
a Clean the basin with water, dry and reinstall.
English 17
CLEANING THE AIR CONDITIONER
* Wipe the unit with a soft dry cloth or clean it, using a vacuum cleaner.
* Do not use hot water or volatile materials which could damage the surface of the air
conditioner.
AT THE BEGINNING OF THE SEASON
* Make sure there are no obstacles blocking the flow of inlet or outlet air.
* Make sure the power supply is properly connected.
PROTECT THE ELECTRONIC SYSTEM
* Indoor unit and remote contro! must be at least 1 meter away from a TV, radio or any other
home electronic appliance.
* Protect the inner unit from direct sun or lighting.
REMOTE CONTROL BATTERY CHANGE
* Remove the batteries from the remote control as shown in Figure 12
* Use two 1.5-Volt, size AAA batteries.
[1 MOVING AND STORING
Before carrying or storing, tilt the outdoor unit to emply it from any remaining condensate
water. The indoor and outdoor units should be joined together (Figure 16) when moving or
storing the air conditioner. To join the units, insert pins (8) of the outdoor unit into the
keyholes (16) of the indoor unit (see Figures 1 and 2).
rm
Figure 15. Removal of Condensate Basin Figure 16. Units Joined for Moving and Storing
English 18
[1 BEFORE CALLING FOR SERVICE
Before calling for service, please check the following common malfunctions and correct as
needed.
PROBLEM CAUSE REMEDY
— The unit does not — Power failure — Check main fuse
operate; standby — Plug is disconnected — Insert plug
indicator does not
light up.
— Unit does not oper- — Remote control malfunc- — Check remote control
ate; stand-by tions. batteries.
indicator lights. — Try to operate from a
closer distance.
— Start from on-unit con-
trols.
~ Perform reset operation
by pressing buttons
(10),(11),(12),(13) for 5
seconds.
— Unit operates for — Improper temperature set- - Decrease temperature
only brief periods in ting. setting.
cooling or dry mode.
— Unit does not — Drainage tube is blocked — Remove obstruction
dehumidify; water — Water pan is full. — Empty through drain
overfiow indicator tube. (Fig. 2-17)
blinks.
— Unit functions but — Window is open. - Close window.
does not perform — Heat-source present in — Remove source of heat.
efficiently. room.
- Unit capacity insufficient — Consult your dealer.
for load or room size.
~ Improper temp. setting. — Adjust temp. setting
— Air filter is blocked. — Clean filter.
English 19
PROBLEM CAUSE REMEDY
— Unit does not re- — IR signal does not reach — Check for obstruction
spond properly to unit. between unit and
remote control com- remote control, clear if
mand. needed.
— Distance between remote — Get closer to unit.
contro! and unit is too big
or aimed at from im-
proper angle.
— IR receiver on unit is ex- — Dim lights, fluorescente
posed to a strong light specially.
source.
— Operating indicator - Compressor operates at — Normai operation of the
blinks. high pressure air conditioner.
— Open a door or window.
— Filter indicator lights — Air filter is contaminated. — Clean filter, reinstall
up. and reset indicator.
~ Noise from the out- — The outdoor condensate — Regular operation of
door unit pump is operating with- the air conditioner
out water.
J
English 20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement