Aeg C9500G-CMI User Manual

Aeg C9500G-CMI User Manual
x GB
x FR
INSTRUCTIONS BOOKLET
tip. Montagnani - Modena - Cod. 535017 1003
- MADE IN ITALY
NOTICE D'EMPLOI
ET ENTRETIEN
mod.
GB
GENERAL INFORMATION
DESTINED TO THE END USER
RECCOMANDATIONS AND PRECAUTIONS
ENVIRONMENT PROTECTION
ATTENTION:
- Before using the appliance, do not forget to remove the plastic
films protecting some parts of the appliance (facia-panel, parts
in stainless steel, etc.)
- Do not use the appliance as a space heater.
- When the appliance is not in use, we recommend to disconnect
the current and to close the gas general tap.
Packing disposal
Sort packing into different materials (cardboard, polystyrene
etc.) and dispose of them in accordance with local waste
disposal laws.
This appliance complies with the following European Directives:
- 73/23/EEC regarding "Low Voltage".
- 89/336/EEC regarding "Electromagnetic Disturbances".
- 90/396/EEC regarding “Gas appliances”
- 89/109/EEC regarding "Materials in contact with food"
- Moreover the above mentioned Directives comply with Directive
93/68/EEC.
- This household appliance has been designed for cooking and
it must therefore be used for this purpose only.
IN CASE OF FIRE:
• In case of fire, close immediately the main valve of the gas
pipe line, disconnect current and never pour water on firing oil
in any case.
• Do not store flammable products or aerosol containers near the
burners, and do not vaporize them near lighted burners.
FOR YOUR SAFETY AND THE ONE OF YOUR CHILDREN.
• Do not store items that are attractive to children above or near
the appliance.
• Keep children well away from the appliance: do not forget that
some parts of the appliance or of the pans become very hot and
dangerous during use, and also for all the time necessary to cool
down.
• In order to avoid any unintentional fall down, pan handles should
be turned to the back of the cooker, not out to the room or over
adjacent burners.
• When cooking, do not use clothes with large flaving and
flammable sleeves; in case of firing you can suffer very serious
harms.
DEAR CUSTOMER,
• Carefully read these instructions before using the appliance and
keep them for future consultation.
• Keep potentially hazardous packaging (plastic bags, polystyrene
etc.) out of the reach of children.
WARRANTY
Your new appliance is covered by a warranty.
The warranty certificate is herewith enclosed. If it is missing, ask
the retailer for it indicating purchasing date, model, and data plate
number which are printed on the data nameplate identifing the
appliance.
Keep the part destined to you, and in case of necessity, show it
to the Technical Service together with the receipt bill.
If you do not follow this procedure, the technical service will be
compelled to charge you with all the fees of each eventual reparation.
You can find the original spare parts only in our Technical Service
and Spare Parts Authorised Centres.
WARNING - OVEN:
When the oven or the grill are in use, accessible parts can
become very hot; it is necessary to keep children well away
from the appliance.
- Never cook food on the lower wall of the oven.
- In case of careless use, in proximity of the oven door hinges,
there is hurt danger.
- Do not let children sit down or play with the oven door. Do not
use the drop down door as a stool to reach above cabinets.
WARMING CABINET
You must not place inflammable materials or plastic utensils in the
warming cabinet (placed below the oven).
TECHNICAL AFTER SALES SERVICE
Before leaving the factory, this appliance has been tested and set
up by skilled personal, in order to give the best performance
results.
Each reparation or set up that could be necessary afterwards,
must be carried out with a great care and attention.
For this reason, we reccommend you to keep always in touch with
the Sales Centre or with our nearer After Sales Service. Specify
always the kind of problem and the model of your appliance.
FOR APPLIANCES WHIT GLASS COVER LID
While using the appliancemake sure that the glass lid does not
touch any pan. After use never close the glass lid while the burners
or the electric hotplates are still hot
2
GB
USE OF THE GAS OVEN
WORK-TOP USE
The first time the oven is used, it may give off acrid smells, caused
by the first heating of isolating panels glue surrounding the oven
(it is necessary to heat up the oven at the maximum
temperature for about 30-40 minutes with closed door).
It is something normal, and in case it will occur, wait for the smoke
to stop before introducing the food into the oven.
The oven is fitted with: a rod shelf for cooking food contained in
oven dishes or placed directly on the rod shelf itself, a drip-tray
for cooking sweets, biscuits, pizzas, etc., or for collecting juices
and fats from food cooked directly on the rod shelf.
warnings: do not cook foods on the bottom in the base of
the oven.
USING GAS BURNERS
The following symbols are on the control panel next to each knob:
.73/23/EEC
.89/336/EEC
.90/396/EEC
.89/109/EEC
.93/68/EEC
- Black circle
gas off
- Large flame
maximum setting
- Small flame
minimum setting
The minimum position is at the end of the anti-clockwise rotation
of the knob. All operation positions must be chosen between the
positions of max. and min., never choose them between max. and
off.
GAS OVEN
MANUAL IGNITION OF OVEN BURNER
To ignite the oven burner, simply insert a match through the
opening (fig. 2) and then turn the tap to the maximum setting as
shown in figure 1.
MANUAL IGNITION
To turn on a burner, approach a match to it, press the knob
corresponding to the selected burner and turn it anticlockwise to
the max position.
Fig. 1
ELECTRIC IGNITION (optional)
To turn on a burner, press the knob corresponding to the selected
burner and turn it anticlockwise to the max position; simultaneously
pressing the electric ignition button on the control panel marked
with symbol
.
In case there is no electric current, the burner can also be lighted
using a match.
= CLOSED
Pos.1 : 140°C = MINIMUM
210
8
0
17
3
0
25
2
= GRILL
4
5
6 7
AUTOMATIC ELECTRIC IGNITION (optional)
To turn on a burner, press the knob corresponding to the selected
burner and turn it anticlockwise to the max position. Keeping the
knob pressed, the electric automatic ignition of the burner will be
started up.
In case there is no electric current, the burner can also be lighted
using a match.
140
1
Pos.8 : 250°C = MAXIMUM
Fig. 2
APPLIANCES WITH SAFETY VALVE (optional)
Follow the same procedure described above to ignite the burners.
In this case, however, once you have turned the knob to the open
setting, hold it pressed in for 10 seconds.
If for any reason the burner flame goes out, the safety valve
automatically shuts off the gas supply to the burner in question.
After making sure that the burner has lit properly, gently close the
oven door. To obtain the temperature required, simply turn the
pointer of the knob to the chosen number .
ENERGY SAVING TIPS
• The diameter of the pan bottom should be the same as that of
the burner. The burner flame must never come out from the pans
diameter.
• Use flat-bottomed pans only.
• Whenever possible, keep a lid on the pan while cooking.
You will not need as much heat.
• Cook vegetables, potatoes, etc. with as little water as possible
to reduce cooking times.
BURNERS
RAPIDE
SEMIRAPIDE
AUXILIARY
TRIPLE CROWN
ULTRARAPID
3
WARNING: Do not operate the ignition for more than 15
seconds. If the burner fails to ignite, leave the oven door open
for at least 1 minute before pressing the knob again.
Electric ignition of oven burner (optional)
The oven door must always be completely open, before the
burner ignition.
Turn the knob anti-clockwise to the maximum position, then press
button
to ignite the burner.
In case there is no electric current, the burner can also be lighted
using a match. (fig 2).
PANS
Ø min.
Ø max
180 mm
320 mm
120 mm
220 mm
80 mm
180 mm
220 mm
320 mm
220 mm
320 mm
Fig. 3
3
GB
Automatic electric ignition (optional)
The oven door must always be completely open, before the
burner ignition
To ignite the burner, press the knob and turn it anti-clockwise to
the maximum position. Keep it pressed to start up the automatic
ignition of the burner.
In case there is no electric current, the burner can also be lighted
using a match.(fig 2).
to ignite the burner.
In case there is no electric current, the burner can also be lighted
using a match.
Automatic electric ignition (optional)
The oven door must always be completely open, before the
burner ignition.
To ignite the burner, press the knob and turn it clockwise to the
grill position
. Keep it pressed to start up the automatic ignition
of the burner.
In case there is no electric current, the burner can also be lighted
using a match (fig.4).
Burner with safety device
For burners fitted with safety device, it it necessary to keep on
pressing the concerned knob for about 10 seconds after the ignition
(fig.3). In this way the safety valve will be started up. If for any
reason the burner flame goes out, repeat the procedure as
described above.
When you will be sure that the burner is on, close softly the oven
door.
To obtain the desired temperature, turn the knob index to the
selected number (tab.B).
Burner with safety device
Repeat the above mentioned procedure, and press the oven knob
at the same time. When the burner is on, keep the knob pressed
for about 10 seconds (fig.3). In this way the safety valve will be
started up. If for any reason the burner flame goes out, repeat the
procedure as described above..
Temperature °C
140 °C
150 °C
160 °C
170 °C
190 °C
210 °C
230 °C
250 °C
Heat the oven 5 minutes before introducing the food.
8
6 7
220
190
175
235
190
200
200
180
290
200
200
250
230
5
0
25
.
210
Fig. A
0
17
WARNINGS: To turn the oven light on, press switch
TEMP.°C
4
185-210
250
220
220
230
235
220
235
225
235
200-225
200-225
FOOD
PASTRY
FRUITCAKE
MARGHERITACAKE
BRIOCHES
SCONES
RING-SHAPEDCAKE
PUFF-PASTE
GRAPESCAKE
STRUDEL
SAVOIABISCUIT
APPLEFRITTER
PUDDING
TOAST
BREAD
210
3
TEMP.°C
140
FOOD
MEAT
ROASTEDPORK
ROASTEDBEEF
ROASTEDVEAL
ROASTEDLAMB
ROASTEDHARE
ROASTEDRABBIT
ROASTEDTURKEY
ROASTEDGOOSE
ROASTEDDUCK
ROASTEDCHICKEN
ROAST-BEEF
FISH
WARNING:
Do not use the grill burner and the oven burner at one and
the same time, other than for the exclusive purpose of
preheating the oven (max 10/20 minutes)
0
25
2
Wait at least 15 minutes before introducing the food, in order to
reach the desired temperature. Below you will find an indicative
cooking table (TAB.C).
TAB. C
140
1
NOTE :
In some models the grill knob is separated from the thermostat
knob.(fig A).
0
17
TAB. B
Knob position
1
2
3
4
5
6
7
8
WARNING: Do not operate the ignition for more than 15
seconds. If the burner fails to ignite, leave the oven door
open for at least 1 minute before pressing the knob again.
NOTE:
The grill must be used with the door half-open (see fig5 A).
Fit the deflector S onto the centring pins N on the top of the oven
opening (fig.5 B ). Then gently close the oven door against the
deflector.
USE OF THE GAS GRILL
(ACCORDING TO THE MODELS)
Manual ignition of the grill
Open the oven door, then turn the oven knob to the right and place
it on the grill position
.
Bring a light match near the holes of the burner placed on the
oven upper part (fig.4).
Use of the gas grill with the oven door closed
Some models are designed for the grill to be used with the oven
door completely closed.
In this case the deflector S shown in fig. 5B is not
supplied.
USE OF THE ELECTRIC GRILL
(ACCORDING TO THE MODELS)
In some other appliances the electric grill can be operated turning
the knob clockwise on position
(fig C-D).
A warning light on the control panel will light up to inform you that
the grill is on.
Note: In some models the grill knob is separated from the
thermostat knob. (fig C)
Fig. 4
Electric ignition of grill burner (optional)
The oven door must always be completely open, before the
burner ignition.
Turn the knob clockwise to the grill position
, then press button
Ø
WARNING:
Do not use the grill burner and the oven burner at one and
the same time, other than for the exclusive purpose of
preheating the oven (max 10/20 minutes)
4
4
Ø
GB
Fig. 6 A
Fig. 6
grill
working light
R
L
F
M
1
P
H
G
I
2
8
3
G
4
5
6 7
Fig. D
Fig. C
R
F
L
Fig. 6 B
second
level
480 mm
mm
240
TURNSPIT single
For utilization of the turnspit follow the instructions described .
- Put the food in spit L (see fig. 7), paying attention to block it within
the two forks F and to balance it, in order to avoid any unnecessary
effort in motor R.
- Put the spit on support G, after having put its opposite end into
hole P of motor R.
- Place the drip-tray with a little water under the spit.
For some models, the turnspit must be used with the oven
door open; in this case, fit the deflector S onto the centring
pins N on the top of the oven opening (fig.5 B ).
- To remote the spit, operate in the opposite direction using knob
S and protecting glove in isolating wool (fig.7).
SURFACE BAKING GRILL
(480x240)
NOTE:
The grill must be used with the door half-open (see fig5 A).
Fit the deflector S onto the centring pins N on the top of the oven
opening (fig.5 B ). Then gently close the oven door against the
deflector.
0
25
140
Use of the electric grill with the oven door closed
Some models are designed for the grill to be used with the oven
door completely closed.
In this case the deflector S shown in fig. 5B is not
supplied.
0
17
210
Fig. 5 A
A
Fig. 5 B
R
P
N
S
F
L
S
Fig. 7
G
USE OF THE TURNSPIT
For the functions of the turnspit turning the knob on the position
(fig E) or on the symbol
(fig C) when the thermostat is
separate or, in some models, press the marked button with the
symbol
.
TURNSPIT multilpe
For utilization of the turnspit follow the instructions described.
- Thread the chicken or the cubes of meat for roasting on the
spit L , ensuring that it is gripped safely between the two forks
F and balancing it properly to avoid unnecessary strain on the
trasmission R (fig 6).
- Put the spit on the support G, after having introduced its
opposite end in the socket P of the transmission R (fig 6)
- Put the support G completely into the oven so that the bar I
goes into the socket H of the turnspit motor M (fig 6A).
- Place the drip-tray with some water under the turnspit, on the
lowest level.
- For some models, the turnspit must be used with the oven door
open; in this case, fit the deflector S onto the centring pins N
on the top of the oven opening (fig.5 B ).
- when removing the spit, wear oven mitts, pull out support G
and use the handgrip A operating in the contrary way (fig 6B).
INSTRUCTIONS FOR USE OF CONTROL DEVICES
(ACCORDING TO THE MODELS)
MINUTES COUNTERS (Fig.8 )
Turn the knob clockwise to set the desired cooking time.
The minutes minder can be adjusted from 1 to 60 minutes.
A sound signal will inform you that the chosen time is up.
10
50
15
45
20
40
35
30
25
Fig. 8
PCI "Campanil"TR 259 Analogic
Setting the clock
Press the control knob and turn clockwise.
1
2
Alarm programme adjustement
Turn the knob clockwise without pressing it in. At the end of the
programmed time an alarm will sound. To cancel it, turn the knob
to the bell.
3
8
55
5
4
Fig. E
5
5
5
6 7
GB
This appliance must be earthed by law. Before connecting
the appliance to the electrical supply, check that the earth
system in your house is working correctly.
Check that unit voltage and power, marked on the rating plate
applied on the appliance, are correct for the supply. It is necessary
that the feeding network is protected by a powerful switch able to
disconnect completely the network with a contacts separation of
at least 3 mm. Be sure that the earth wire green/yellow is not
interrupted by the switch.
Important: The wires in the mains lead are so coloured:
- green/yellow = earth " "
- blue
= neutral “N”
- brown
= live “L”
The wire coloured green/yellow must be connected to the terminal
in the plug which is marked with letter 'E' or by the earth symbol
or coloured green or green/yellow. The wire coloured blue must
be connected to the terminal which is marked with letter 'N' or
coloured black. The wire coloured brown must be connected to
the terminal which is marked with letter 'L' or coloured red. The
supply cable must not come into contact with any component the
temperature of which exceeds the ambient temperature by 50°C.
If a plug is used for connection, the plug to be connected to the
supply cable and the socket to which it is connected must be of
the same type (conforming to the standards). Easy access to the
plug or the switch is ensured once the appliance is installed. Ensure
that there is sufficient cable allowed for any subsequent removal
of the unit. If the plug is non-rewireable, pay attention to the
following points: the plug must never be cut by the supply cord.
There is shock hazard when this plug is inserted in a socket-outlet
elsewhere in the house. Never use the plug without the fuse cover
fitted. Referring to the pertinent spare parts, apply to the appliance's
supplier. The manufacturer declines all responsibility for any
damage to persons or things caused by failure to observe
the rules indicated above.
VI VII
Timer setting
This function is permanently activated and it will be immediately
set with +/- buttons.
During setting the units are 10 seconds.
During count down the timer takes priority on the display.
The units are seconds.
The maximum time is 99 minutes.
The relay contact (when available) is closed during the count down
only.
Reset timer
Press “+” and “-” buttons together and release “+” button first.
Applance type
Signal
The signal after time out will stay 7 minutes if it has not been reset
with the “+” button (one touch only).
Aii gas
All gas + elett. grill
Signal frequency
When the display shows the time of day, the signal frequency can
be selected by pressing the “-” button. Three different frequencies
are selectable.
S
R
P
F
L
S
G
Supply single-phase 230 V~
Type of cable
section
Rubber H05 RR-F 3 x 0,75 mm2
3 x 2,5 mm2
Rubber H05 RR-F
55
5
50
45
40
REPLACEMENT OF THE CABLE
In case the cable is damaged, replace it in accordance with the
following instructions:
- open the box of the supply board as described on the picture
below;
- unscrew screw “A” fixing the cable;
- replace the cable with one of the same lenght and in accordance
with the features described on the table; switch the appliance
off, and close the gas tap
- the ‘green-yellow” earth wire must be connected to the terminal
“
“ and it must be about 10 mm longer thean the live wires;
- the “blue” neutral wire must be connected to the terminal marked
with letter “N”;
- the live wire must be connected to the terminal marked with letter
“L”.
Fig. 9
N
10
V
Time setting
Press the left button.
Set the time with buttons “+” and “-”.
This function remains activated 7 seconds after the last +/operation.
B5
A5
15
VIII
IV
On
The display flashes.
A
20
X
IX
III
Functions
B
L
25
II
ELECTRONIC TIMER FOR COOKER (Fig. 9)
F
30
I
35
XI
XII
E
L
1 Time of the day
2 Timing and insertion
3 Signal timng and insertion
B
R
N
L
A
F
M
ELECTRICAL CONNECTION
P
H
G
I
Connection of the appliance to the power mains should be done
by a licensed electrician familiar with local safety regulations.
R
A
6
G
6
GB
XI
XII
INSTRUCTIONS DESTINED TO THE USER
CARE AND MAINTENANCE
I
1450/1500
610
895
WARNINGS
The technical data are indicated on the data nameplate placed
on the rear of the appliance.
The adjustment conditions are stated on the label applied on the
packaging and on the appliance.
Do not use the oven door handle to move the appliance, such as
to remove it from the packaging.
The appliance is in class 1 or class 2 subclass 1.
GRIDS AND BURNERS
To clean the work-top burners, remove them by pulling upwards
and soak them for about 10 minutes in hot water with a little
detergent. After having cleaned and washed them, wipe them
carefully.
Make sure that no burner hole is clogged.
Clean the burners once a week or more frequently if necessary.
MAKE SURE YOU HAVE ASSEMBLED THE BURNERS IN A
RIGHT WAY.
INSTALLATION
IMPORTANT: The coating of the furniture must be able to withstand
high temperatures (min. 90°C).
If the appliance is to be installed near units, leave the minimum
gaps specified in the table below.
OVEN DOOR
For some models, the oven door can be disassembled in the
following way:
hinges A are provided, for this purpose, with two movable jumpers
B; these, once hooked to the hinges slots C, when the door is
completely opened, block them. After that lift the door outward
carring out the two movements shown in the picture. To do that,
operate on the door sides next to the hinges. In order to reassemble the door, introduce the hinges in their relevant slots.
Before closing the door, do not forget to remove the movable
jumpers B.
Attention, in proximity of the oven door hinges, there is hurt danger.
H05 RR-F
H05 RR-F
850/900
VI VII
ENAMELLED SURFACES
Clean with a damp sponge using soap and water.
Grease can be easily removed using hot water or a specific
cleansing agent for enamelled surfaces. Do not use abrasive
cleansers.
Do not leave any acid or alkaline substances (lemon juice, vinegar,
salt, etc.) on the enamel.
Clean the parts in stainless steel with specific cleansers for
stainless steel surfaces.
These detergents must be applied using a soft cloth.
100
V
N
min.50mm
mn
i2.0mm
mn
i.100
mm
min.50mm
mn
i2.0mm
min. 400 mm
VIII
IV
IMPORTANT
Periodically check the external gas connection hole and
replace it when it shows any sign of deterioration. Do not
attempt to repair the gas hose under any cincumstances.
910/960
IX
III
OVERALL DIMENSIONS
min. 650 mm
X
II
Before cleaning the appliance, disconnect the gas general
tap and unplug the appliance or disconnect power at the
main circuit breaker of the electrical system.
Do not clean the appliance surfaces when still hot.
B C
L
A
N
The cooker is fitted with 4 legs for an eventual alignment in height
with the furniture. To assemble them, it is necessary to raise the
cooker and to screw the four legs into the suitable threadings
placed on the corners on the bottom of the appliance .
OVEN
Clean the enamelled parts with a damp sponge using soap and
water. Grease can be easily removed using hot water or a specific
cleansing agent for enamelled surfaces.
Do not use abrasive cleansers.
A
895
7
7
GB
The appliance must be connected to the gas piping in a workmanlike
way and in conformity with the regulations in force which lay down
the installation of a safety valve at the end of the piping.
For butane and propane a pressure reducer conforming to the
standards in force may perform this task.
The seal gaskets must be in accordance with rules.
Once the gas appliance has been connected, check the connection
seal by means of soapy water.
The end of the attachment is threaded.
The possible connections are:
ROOMS VENTILATION
GAS APPLIANCES
This appliance is not connected to a device to vent the combustion
products. It must therefore be installed and connected in conformity
with the installation standards in force.
Particular attention must be paid to the standards on ventilation
of the room.
1/2”
- by rigid pipe in iron or copper
- by flexible tube in stainless steel with continuing wall, with
mechanical connection in accordance with rules. The tube must
be directly connected to the manifold elbow (see Fig.34).
- by the insertion of a rubber tube in accordance with rules.
This tube must be connected directly on the push-on connector,
concerning the gas used, and it must be blocked with a band.
In the last case, check the tube's printed date of expiry and
replace it before this date.
VENTILATION OF ROOMS
Remember that this appliance can be installed and work in wellventilated rooms only, according to the standards in force, such
as to allow, with openings on the external walls or with special
ducts, a correct natural or forced ventilation ensuring permanently
and sufficiently both the entry of the air needed for correct
combustion and the removal of spent air.
In particular when there is only this gas appliance in the room,
there must be a hood over the appliance to ensure the natural and
direct removal of spent air, with a vertical straight duct of length
equal to at least twice the diameter and a minimum section of at
least 100 cm2.
For the indispensable entry of fresh air into the room there must
be a similar 100 cm2 opening directly to the outside, situated at
a height near floor level so that it is not blocked either inside or
outside the wall and so as not to cause disturbances to correct
burners combustion and to the regular removal of spent air and
with a difference of height with respect to the outlet opening of at
least 180 cm.
Remember that the quantity of air necessary for combustion must
never be less than 2m3/h for each kW of power (see total power
in kW on the appliance data plate).
In all other cases, i.e. when there are other gas appliances in the
same room, or when natural direct ventilation is not possible and
natural indirect or forced ventilation must be installed, contact a
qualified specialist who will install and make the ventilation system,
scrupulously observing the regulations contained in the standards
in force.
The openings must be so positioned that there are no draughts
of air which cannot be tolerated by the occupants.
Moreover to eliminate combustion products, it is forbidden to use
flues already used by other appliances.
WARNINGS
Concerning rubber flexible tubes (max. length 1500 mm), we
remember you:
1 - to avoid the tube to be narrowed or crushed
2 - do not submit it to traction or torsion efforts
3 - to avoid contact with sharp edges, etc...
4 - to avoid contact with parts reaching temperatures over 70°C
the ambient temperature
5 - to ensure that they can be checked for all their length.
c
HOSE
ATTACHMENT
FOR LIQUID
GAS
F
HOSE
ATTACHMENT
FOR NATURAL
GAS
F
Fig. 10
min. 180 cm.
min. 180 cm.
electrical fan
min. 100cm2.
B C
If the connecting tube must be passed behind the appliance,
observe the regulations of the picture, making sure in the last case
that the tube is kept in support A.
A
min. 100cm2.
GAS CONNECTION
STOP
We recommend to check wether the appliance has been foreseen
for the kind of gas distributed.
INLET
895
8
8
GB
GAS ADJUSTMENT
"
If the appliance is foreseen to operate with a type of gas different
from the suitable supply gas, proceed as follows: change the
injectors, adjust the minimum flow of the burners, change the
push-on connector.
In order to change the work-top injectors, it is necessary to act as
follows: remove the grids, remove burners and flame-spreaders
(see fig.A), change the injector (see fig.B) and replace it with
another one suitable for the new type of gas (see table D). Reassemble everything in the opposite direction, paying attention to
place the flame-spreader in the right way on the burner.
¦
C
FIG.F
FIG.G
TAB. D
Kind of gas
A
B
NATURAL
To change the oven injector, it is necessary to act as follows: open
the oven door, remove the lower side of the oven (see fig.C),
unscrew screw C and disassemble the oven burner (see fig.D).
Change the injector (see fig.E) and replace it with another one
suitable for the new gas type (see table D).
Re-assemble everything in the opposite direction, paying attention
to place the burner in the right way on its rear slot.
F
G.P.L.
BUTANE
PROPANE
NATURAL
G.P.L.
BUTANE
PROPANE
F
GENERAL INJECTORS TABLE
mbar Nozzle
Burners
Power Watt Consum.
N. Position-type
max. min.
max.
1.15 Rapide
3000 750
286 l/h
20
0.97 Semi rapide
1750 480
167 l/h
0.72 Auxiliary
1000 330
95 l/h
1.28 Triple crown
3300 1300 315 l/h
1.45 UltraRapide
3600 1500 343 l/h
1.20 Fish
2900 1500 277 l/h
1.50 Oven
4300
389 l/h
1.45 Grill
3800
344 l/h
30
0.85 Rapide
3000 750
219 g/h
28
0.65 Semi rapide
1750 480
128 g/h
37
0.50 Auxiliary
1000 330
73 g/h
0.93 Triple crown
3300 1300 241 g/h
0.96 UltraRapide
3600 1500 262 g/h
0.85 Fish
2900 1500 211 g/h
1.00 Oven
4300
313 g/h
0.95 Grill
2800
277 g/h
with separated thermostat
20
1.25 Grill
2800
253 l/h
30
0.75 Grill
2800
204 g/h
28
37
MINIMUM FLOW ADJUSTMENT FOR WORK-TOP TAPS
In order to adjust the minimum, act as follows: switch the burner
on, and turn the knob towards the minimum flow position .
Remove the knob from the tap, introduce a little screwdriver in the
tap rod (fig. 11).
Attention: in taps with security valve, the minimum adjusting screw
“Z” is placed outside the rod tap (fig. 12).
FIG.C
C
Z
FIG.D
Fig. 11
FIG.E
MINIMUM FLOW ADJUSTMENT FOR OVEN THERMOSTAT
In order to adjust the minimum, act as follows: switch the burner
on turning the knob to the maximum position.
Remove the knob and unscrew of some turns the by-pass screw
(fig. H).
Assemble the knob and let the oven warm up for 15 minutes; after
that turn the knob to the minimum position.
To change the grill injector, it is necessary to act as follows: open
the oven door, unscrew screw C and disassemble the grill burner
(see fig.F). Change the injector (see fig.G) and replace it with
another one suitable for the new gas type (see table D).
Re-assemble everything in the opposite direction, paying attention
to place the burner in the right way on its rear slot.
9
Fig. 12
Unscrew the adjusting screw in order to increase the flow or screw
it to decrease the flow.
The right adjustment is obtained when the flame has a length of
about 3 or 4 mm.
For butane/propane gas, the adjusting screw must be tight screwed.
Make sure that the flame does not go out passing quickly from
the max. flow
to the minimum flow
and viceversa .
Assemble the knob again.
9
GB
DISASSEMBLE OF WORK-TOP
In case it is necessary to repair or replace the inside components,
act as follows:remove the glass lid from its position slipping off it
upwards.
Remove the grids, remove burners and flame-spreaders (see
fig. 13), unscrew the visible screws “V” placed on the work-top
(see fig. 14). Disassemble the work-top by unscrewing the 4 rear
screws “A” (see fig. 15 ).
After having removed the knob once again, making sure that the
thermostat rod has not been moved, screw slightly the above
mentioned by-pass screw, to obtain a flame of 3 or 4 mm of length.
For butane/propane gas, the adjusting screw must be tight screwed.
Make sure that the flame does not extinguish passing quickly from
the maximum flow to the minimum flow, and closing and opening
the oven door (the oven door must be closed softly).
Attention: for taps with safety device, the minimum adjusting screw
“T” is on the outside of the tap rod (fig. I ).
A
T
Fig. H
B
V
Fig. 14
Fig. 13
Fig. I
REGULATION AIR ADJUSTER
REGULATION OF AIR ADJUSTER (oven burner )
To do this,
- Unscrews the screw (A ) in order to rotate the metal ring at the
end of the burner (fig L ).
In this way, entrace of the air increases or descreases, obtaining
a correct flame.
Be sure that the flame does not lift or light back or present a
yellow colouration .
A
Fig. 15
- To disassemble the control panel, unscrew the 4 internal screws
(B) fixing the control panel to the oven face ( fig 16 ).
REGULATION OF AIR ADJUSTER (grill burner )
To do this,
- Unscrews the screw (A ) in order to slip it forwards or backwards
(fig M).
In this way, entrace of the air increases or descreases, obtaining
a correct flame.
Be sure that the flame does not lift or light back or present a
yellow colouration .
B
GREASING OF TAPS
WARNING:This operation must be carried out by skilled staff.
If a tap becomes hard to be turned, grease it using a specific
grease withstanding high temperatures. Act as follows: switch the
appliance off, and close the gas tap open the work-top and
disassemble also the control panel as described on the previous
paragraph. Unscrew the two fixing screws from the burner body
(see picture) and remove the cone.
A
Clean the cone and its slot by means of a cloth soaked with diluent.
Slightly grease the cone with the relevant grease, put it in its slot,
and turn it some times. Remove the cone again, remove the
exceeding grease making sure the gas entries are not obstructed
by grease residuals. Assemble everything carefully in the opposite
direction check the connection seal by means of soapy water.
A
Fig. L
C
Fig. 16
Fig. M
APPLIANCE MAINTENANCE
Z
TAPS REPLACEMENT
Act as follows: switch the appliance off, and close the general tap
open the work-top and disassemble also the control panel as
described on the previous paragraph. Unscrew screw nut D of the
gas tube supplying the burner. Unscrew screw V fixing the tap to
the bridle and remove it (see picture).
Note: Every time the tap is replaced, it is necessary to replace the
seal gasket too check the connection seal by means of soapy
water (see picture).
WARNINGS
Isolate the cooker from the electricity supply before attempting to
replace the oven lamp.
The oven lamp used is of a special type withstanding high
temperatures. To replace it, act as follows: disassemble the
protecting glass (A) and replace the burnt lamp with one of the
same type. Reassemble the protecting glass.
E 14
25 W - 230 V~
T300°C
D
C
15
V
A
7
10
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement