Electrolux | Z5533 | User manual | Electrolux Z5533 User Manual

11047 Electrolux VC
12/11/1998 1:08 pm
Page 1
Title: Electrolux Perfexio ID: English (GBB) Proof No: 06 Page: 1
English
5510 • 5520 • 5525 • 5530
5535 • 5540 • 5550 • 5560
Before you start, please refer to the electrical safety instructions on
page 63 (Great Britain only).
Please keep both flaps open when reading these operating
instructions.
Tools for your Vacuum Cleaner
B Dust bags
C
B
D
w
E
F
X
G
H
I
s
K
Telescopic tube 5510
Back saver tube 5520/25/30/35/40/50/60
Your Vacuum Cleaner features
Hose handle 5510/20/25/30/35/40
Hose handle with remote control 5550/60
A
Carpet/hard floor nozzle
B
Turbo nozzle 5540
C
Power nozzle 5560
D
Crevice nozzle
E
Upholstery nozzle 5510/20/25/30/35/40
F
X Mains cable
Y
z
0
1
2
Cable foot pedal
3
l
m
4
g
K
w
i
5
k
Dust bag full indicator 5530/35/40/50/60
Dusting brush 5510/20/25/30/35/40
Combination nozzle/brush 5550/60
Tool holder 5510/20/25/30/35/40
Ensuring your safety
The cleaner is for domestic use only and has been designed to
ensure maximum safety and performance. Please follow these
simple precautions:
L
M
N
O
P
Q
R
S
T
U
W
• Extend cable and connect to mains ensuring cable is not twisted.
Move foot pedal forward to reel cable in/out as required. Move foot
pedal back to lock extended cable in place. Press foot pedal to
rewind (please hold the plug to prevent it striking you or the machine).
• Press on/off foot pedal to activate cleaner. (Press on/off foot pedal
to place cleaner on standby. Indicator will illuminate 5550/60).
• To increase/decrease suction, adjust control on cleaner body
5510/20/25/30/35/40 or hose handle 5550/60. Suction can
also be regulated on hose handle 5510/20/25/30/35/40 by
opening/closing aperture.
The cleaner is double-insulated so it must not be earthed
G
H
I
J
K
L
The cleaner is only to be used by adults
Always store in a dry place
Do not pick up hot cinders or lighted cigarette ends
Do not use near flammable gases
Getting started
• Check dust bag is in place.
• Insert hose 5510/20/30/35/40 and pins 5550/60 until catch
clicks to engage (Press catch to release).
• Attach telescopic tube 5510 or back saver tube
5520/25/30/35/40/50/60 to hose handle.
• Attach floor nozzle to tube.
• Use back saver tube 5520/25/30/35/40/50/60 in positions
shown for normal cleaning or cleaning under low furniture.
To adjust, press catch and twist lower tube.
Standby/Overheat Indicator: Indicator will ‘illuminate’ when
cleaner is on standby 5550/60, and ‘flash’ if cleaner
overheats 5530/35/40/50/60
Cover release for dust bag/filter compartment
Hose connection
Power outlet (for the use of power driven tools)
5530/35/40/50/60
Back saver carrying handle
Tool holder (for attachment to hose handle)
5510/20/25/30/35/40
N
On/off switch
O
P
Temporary parking position for floor nozzle and extension
tubes when in use
Storage slot for floor nozzle and extension tubes
Getting the best results
Note: Do not use cleaner with a damaged cable. If damaged
the cable should be replaced at an Electrolux Service Centre
All service and repairs must be carried out by authorised
Electrolux service staff
CleanStream filter indicator 5530/35/40/50/60
Hose handle with suction regulator, power nozzle on/off
switch, power nozzle socket 5550/60
Avoid tugging on the mains cable and check cable regularly
for damage
The plug must be removed from the socket-outlet before
cleaning or maintaining the appliance
Dust bag full indicator 5510/20/25
M
Do not use to pick up liquids
Avoid sharp objects
Suction control regulator 5510/20/25/30/35/40
Using Carpet/Hard floor nozzle
v
u
45
Carpets: Use floor nozzle with lever in this position.
Reduce suction power for loose rugs.
Hard floors: Use floor nozzle with lever in this position.
6
Using Turbo nozzle 5540 or Power nozzle 5560
Precautions: Only use nozzle on carpets with a pile depth
under 15 mm. Do not use on animal skins or rugs with long
fringes. To avoid damaging your carpet, do not keep nozzle
stationary whilst brush is rotating. Do not pass nozzle over
mains cable and switch off nozzle immediately after use.
• Attach turbo nozzle 5540 or power nozzle 5560 to tubes.
• Connect power nozzle plug to hose handle socket and use
clips to secure cable to tube 5560.
• Push on/off switch to activate power nozzle 5560.
• Note: Suction can also be regulated on turbo nozzle by
opening/closing air vent 5540.
11047 Electrolux VC
12/11/1998 1:08 pm
Page 2
Title: Electrolux Perfexio ID: English (GBB) Proof No: 06 Page: 2
The Global Appliance Company
Cleaning Turbo nozzle 5540 or Power nozzle 5560
• Disconnect from mains and remove entangled threads from
nozzle by snipping threads with scissors.
• To clean inside nozzle, open cover by unscrewing 5540 or
by releasing catches 5560.
• Remove brush cylinder and supports. Clean as necessary
and replace. To clean wheels, gently lever them from their
mountings. Replace cover ensuring it is properly fastened.
Using combination nozzle/brush 5550/60
• Use in position shown for cleaning upholstery.
• Use in position shown for dusting. Attach to hose handle
for storage.
Dust bag indicator and changing the dust bag
The dust bag should be changed when full.
5510/20/25 the dust bag indicator window will turn red when
filling and completely red when full. 5530/35/40/50/60 the dust
bag indicator window will light up when full. If the dust bag
should accidentally get broken in the cleaner, take cleaner to
Electrolux Service Centre for cleaning.
2
The Micro filter 5510/20/25 should be changed every
fifth dust bag.
To change Micro filter:
G) Open the filter cover.
H) Replace filter and close cover ensuring it is properly fastened.
The CleanStream filter should be cleaned when the indicator
light is on 5530/35/40/50/60.
To clean the CleanStream filter:
I) Open the filter cover and remove filter unit.
J) Rinse the inside (dirty side) of the filter unit under warm tap
water only, keeping the outside dry. Do not use cleaning
agents and avoid touching the delicate filter surface.
Tap the filter frame to remove excess water. Repeat
cleaning procedure four times and allow the filter to air dry.
The original filtering performance is now restored. Replace
the unit back into the cleaner and close cover ensuring it is
properly fastened.
Troubleshooting
To check the dust bag, the cleaner must be switched on,
with all attachments connected and off the floor.
Power: If the electric power does not come on, disconnect
from mains and check plugs, cable and fuses where appropriate.
The dust bag full indicator may signify that the bag is blocked
(occasionally caused by very fine dust) which will cause loss of
suction and may result in overheating. If this occurs change
the dust bag even if it is not full.
The cleaner may switch itself off in event of severe blockage
or excessively dirty filters (on 5530/35/40/50/60 overheat
indicator will flash). In such cases, disconnect from mains and
allow to cool for 30 minutes. Clear blockage and/or replace
filter(s) and restart.
To change the dust bag:
A) Open the cleaner cover.
B) Pull the sliding tab to remove the dust bag.
C) Insert new dust bag by sliding the bag slots into the holder.
Close cover.
We recommend the dust bag is changed:
* After using a carpet cleaning powder.
* If there is a bad smell from the cleaner, then you should also
change the filter.
Note: Use only Electrolux original dust bags and filters:
Micro filter (ref. EF 17)
CleanStream filter (ref. EF 25)
The cleaner features a safety valve. The valve feeds cool air to
the machine in case the hose or tube is blocked. The valve
may also trigger e.g. when vacuum cleaning carpets or other
soft materials. When the nozzle is lifted, the valve is reset.
If the safety valve triggers repeatedly during normal use, check
and remedy any blockage in the hose, tube, nozzle or filters.
The clearing of blocked hoses is not covered by the guarantee.
To avoid blockages and maintain suction efficiency, the floor
nozzles should be cleaned regularly using the hose handle.
Water: If water is sucked into the cleaner the motor must be
changed at an Electrolux Service Centre.
If you have any comments on the cleaner or the Instruction for
Use Booklet please e-mail us on: floorcare@electrolux.se
Dust bag safety device
To avoid damaging the cleaner, do not use it without a dust
bag. A safety device is fitted which prevents the cover closing
without a dust bag. Do not attempt to force cover shut.
Changing the filters
Never use the cleaner without the filters in place. The Motor
Protection filter should be changed twice a year for normal usage.
To change Motor Protection filter:
D) Open the cleaner cover.
E) Remove filter and covering strip.
F) Important: Insert new filter with original covering strip
securely in place. Close cover.
ANY PROBLEMS?
Something missing?
Don’t understand the instructions?
Need more help?
DON’T TAKE
IT BACK TO THE SHOP
We are only a telephone call away.
CUSTOMER HELPLINE
08706 055 055
Download PDF

advertising