Whirlpool | AMD 054 | Instruction for Use | Whirlpool AMD 054 Instruction for Use

BEFORE USING THE APPLIANCE
To make the most out of your new appliance, please read the user instructions carefully and keep them
handy for future consultation.
SAFETY PRECAUTIONS
• Never block the air inlet or outlet of indoor and
outdoor unit.
• Physically or mentally disabled people, children
and people without any experience with the
product are only allowed to use the appliance if
they have had specific training on how to
operate the appliance by a person responsible
for their security and well-being. The appliance
is not intended for use by disabled people and
very young children without supervision.
• Children should be supervised to ensure that
they do not play with the appliance (including
remote control).
• The Installation and service/repair must be
performed by a qualified technician, in
compliance with the producer's instructions and
following local safety norms. Do not repair or
replace any parts of the appliance unless it is
specifically written in the user instructions.
• Do not pull the power supply cord to remove it
from the socket. Do not twist or press the
power supply cord, and make sure it is not
broken.
• Do not touch the power plug, circuit breaker
and emergency button when your hands are
wet.
• Do not insert your fingers or foreign substances
into the air inlet/outlet of indoor&outdoor unit.
AIR CONDITIONER PRECAUTIONS
Please strictly follow the below instructions:
• Long and direct exposure to cool air might be
harmful to health. It is advisable to set the
louvers in order to avoid direct cool air and
deflect it within the room.
• Upon malfunctioning first turn the appliance off
by pressing the ON/OFF button on the remote
control, then disconnect it from power supply.
• Do not switch the appliance on and off too often
as this can damage the appliance.
• Do not place any objects on the outdoor unit.
• Disconnect the air conditioner from the power
supply if it is to be left unused for a long period
of time or during a thunder/lightning storm.
• This product contains Fluorinated Greenhouse
Gases covered by the Kyoto Protocol, the
refrigerant gas being in a hermetically sealed
system. Refrigerant gas: R410a has a Global
Warming Potential (GWP) 1975.
29
SAFEGUARDING THE ENVIRONMENT
• This appliance has been made of recyclable or
re-usable material. Scrapping must be carried
out in compliance with local waste disposal
regulations. Before scrapping it, make sure to
cut off the mains cord so that the appliance
cannot be re-used.
• For more detailed information on handling and
recycling of this product, contact your local
authorities who deal with the separate collection
of rubbish or the shop where you bought the
appliance.
SCRAPPING OF APPLIANCE
• This appliance is marked according to the
European Directive 2002/96/EC, Waste
Electrical and Electronic Equipment (WEEE).
• By ensuring that this product is disposed of
correctly, you will help to prevent potentially
negative consequences for the environment and
for human health.
• The symbol
on the product or on the
documents accompanying the product indicates
that this appliance should not be treated as
household waste, but must be given to the
appropriate local gathering place where electric
and electronic appliances are stored and
recycled.
SCRAPPING OF PACKAGING
• The packaging can be 100% recycled as
confirmed by the recycling symbol
. The
various parts of the packaging must not be
dispersed in the environment, but must be
scrapped in line with local authority regulations.
30
PRODUCT DESCRIPTION
Indoor unit
1. Air Intake
2. Front Panel
3. Display panel
4. Air Outlet
5. Electrical box
6. On/off switch
7. Vertical Adjustment Louver
8. Horizontal Adjustment Louver
9. Air Filter
10. Remote Control
Outdoor unit
11. Air Intake
12. Pipes and Power Connection Cord
13. Drain Hose
14. Air Outlet
Images in the user instructions are based on external views of standard models, shape and design vary
according to the model.
31
CONTROL PANEL DISPLAY INDICATORS
DESCRIPTION
Temperature indicator (1)
Displays set and room temperature.
Running indicator (2)
It lights up in white when connecting to power supply.
It lights up in white during operation.
Heating indicator (3)
It lights up during heating mode.
Cooling indicator (4)
It lights up during cooling mode.
Dehumidifying indicator (5)
It lights up during Dehumidifying mode
Super Silent indicator (6)
It lights up during Super Silent mode
Signal Receptor (7)
32
REMOTE CONTROL FUNCTIONS
AND INDICATORS
1.
ON/OFF BUTTON
Starts and/or Stops the appliance by pressing
this button.
2-3. TEMPERATURE SETTING BUTTONS
Used to set temperature.
Used to set time for clock.
Used to set time in timer mode.
4.
5.
6.
7.
1
MODE BUTTON
Used to select the operation mode.
3
2
BUTTON
Used to set 6th sense operation.
4
5
8
6
BUTTON
Used to set or cancel around U operation
FAN BUTTON
Used to select fan speed.
11
7
12
15
9
10
14
13
8.
SWING BUTTON
Used to stop or start vertical adjustment
louver swinging and sets the desired
up/down airflow direction.
9.
POWER SAVE BUTTON
Used to set or cancel power save operation
13.
AUTO CLEAN BUTTON
Used to set or cancel auto clean operation.
10
T-ON/T-OFF BUTTON
Used to set or cancel the timer operation.
14.
CLOCK BUTTON
Used to set the current time.
11.
JET and LIGHT BUTTON
Used to start or stop the fast cooling and
heating operation.
Used to turn on/off display light on indoor
unit.
15.
SLEEP BUTTON
Used to set or cancel Sleep operation.
16.
SUPER SILENT BUTTON
Used to set or cancel the super silent
operation.
12.
16
INFO °C BUTTON
Used to display room temperature or set
temperature on indoor unit control panel.
33
INDICATOR SYMBOLS ON RC DISPLAY
indicator
Cooling indicator
1
Dehumidifying indicator
Sleep indicator
Fan only indicator
Around U indicator
Heating indicator
Jet indicator
FAN
Auto fan speed
FAN
High fan speed
FAN
Medium-High fan speed
FAN
Medium fan speed
Temperature display
FAN
Low-Medium fan speed
Set temperature dispaly indicator
FAN
Low fan speed
Room temperature display indicator
Auto clean indicator
Front panel display light on indicator
Swing indicator
Super silent indicator
Lock indicator
Anti-freeze indicator
Signal transmission
Display set timer
Display current time
°F
Cold plasma generation indicator
34
STORAGE AND TIPS FOR USING THE
REMOTE CONTROL
How to insert the batteries
1. Gently press down on the battery cover and
push in the direction of the arrow to remove, as
shown.
2. Put 2 AAA batteries (1.5V) into the
compartment. Ensure that "+" and "-" polarity is
correctly positioned.
3. Close the battery cover on the remote control.
1
How to remove the batteries
Remove the battery cover in the direction of the
arrow.
Press the positive pole of the battery softly with
your fingers, then draw the batteries out of the
compartment.
All this should be done by adults, children are
forbidden to remove the batteries from the
remote control in order to avoid danger of
swallow.
2
3
Disposal of the batteries
Please discard the batteries as sorted municipal
waste at the accessible collection point.
Precautions
• When replacing the batteries, do not use new
batteries with old batteries, or different types of
batteries as this may cause the remote control
to malfunction.
• If you do not expect to use the remote control
for some time, take the batteries out to prevent
leakage of battery acid in the remote control.
• Operate the remote control within effective
range. Keep the remote control at least 1 meter
from any TV set or HI-FI equipment.
• If the remote control does not work normally,
take the batteries out and reinstall after 30
seconds. If it still does not work install new
batteries.
• To operate the appliance by remote control,
point the remote control at the receiving device
on the indoor unit, to ensure receiving
sensibility.
• To send a message from remote control, the
symbol
will flash for 1 second. On receipt
of the message, the appliance will emit a beep.
• The remote control will operate the air
conditioner at a distance of up to 7m.
• Each time the batteries are replaced in the
remote control, the remote control is pre-set at
6th Sense mode.
Signal receptor
35
OPERATING MODE DESCRIPTION
General Operation:
1. Turning on
Press On-Off button, when the appliance receives
the signal, the RUNNING indicator on indoor unit
dispaly lights up. During mode changes wait a few
seconds and repeat the operation if the appliance
does not respond at once. When setting the
heating operation, air flow will start after 2-5
minutes.
Cold Plasma Generator
This function is active when the product power on,
icon
displays on remote control. It generates
hydrogen(H) and oxygen(O2) and neutralizes
viruses, bacteria and allergens by decomposing
such harmful particles. It creates a healthy
environment by improving the air quality in your
home and it makes you breathe better.
2. Selecting mode
Each time the Mode button is pressed, the
operation mode is changed in sequence:
6th SENSE mode
COOLING mode
DEHUMIDIFYING mode
FAN only mode
HEATING mode
3. Setting FAN speed
Each time the Fan button is pressed, the fan speed
is changed in sequence:
Only low fan speed is available under
Dehumidifying mode.
Auto
FAN
Auto fan speed
FAN
Low fan speed
FAN
Low-Medium fan speed
FAN
Medium fan speed
FAN
Medium-High fan speed
FAN
High fan speed
4. Setting temperature
+ Press once to raise temperature setting by 1 °C
- Press once to lower temperature setting by 1 °C
When pressing + or - button and hold it down,
the number will change rapidly.
Range of available set temperature: 16°C~30°C
*Note: In 6th SENSE mode the temperature
cannot be set.
36
AIRFLOW DIRECTION CONTROL
5. Airflow direction control
Vertical airflow is automatically adjusted to a
certain angle in accordance with the operation
mode after turning on the appliance. The direction
of airflow can be also adjusted to your own
requirement by pressing the Swing button of the
remote control.
Vertical airflow control (using the remote
control)
Each time the Swing button is pressed, vertical
airflow is changed in sequence:
When the vertical adjustment louver starts to
swing up and down, if this button is pressed, the
louver will stop at current position. When the
status is switched from off to , if this button is
pressed again 2 seconds later, status will switch to
off status directly; if this button is pressed again
within 2 seconds, the change of swing status will
follow the sequence stated above.
Press SWING button continuously for more than
2s, the main unit will swing back and forth from up
to down, and then loosen the button, the unit will
stop swinging and present position of louver will
be kept immediately.
Horizontal airflow control (with hands)
Turn the control rods of the horizontal adjustment
louvers to change horizontal air flow as shown.
Note: The shape of the appliance may look
different from that of the air conditioner you have
selected.
A - Do not turn the vertical adjustment louvers
manually, otherwise malfunction may occur. If
that happens, turn off the appliance first and
cut off the power supply, then restore power
supply again.
B - It is better not to let the vertical adjustment
louver tilt downward for a long time at
COOLING or DRY mode to prevent
condensed water from dripping.
control rod of horizontal
adjustment louvers
37
MODE AND FUNCTION DESCRIPTIONS
6th SENSE MODE
Press the
button,
will display, the appliance
enters 6th sense mode directly.
In this mode, temperature and fan speed will be
automatically set based on the actual room
temperature.
Heat pump models
Indoor
temperature
Operation mode
22°C or below
HEATING
22°C-26°C
FAN or keep previous mode
26°C or over
COOLING
Button is ineffective in Jet and Sleep mode.
Note: Temperature will not be displayed on front
panel and remote control under this mode.
What you can do in 6th sense mode
Your feeling
button
adjustment procedure
Uncomfortable because of unsuitable
air flow volume.
Indoor fan speed alternates among High, Medium
and Low each time this button is pressed.
Uncomfortable because of unsuitable
air flow direction.
Please refer to the previous chapter "Airflow
direction control"
Around U function
When you press this button,
will display,
remote control transmits the actual room
temperature around it to the indoor unit,
and the appliance will operate according to this
temperature to let you feel more comfortable.
Please keep the remote control in a location
where it can transmit the signal to the indoor unit
properly.
Press once to set and press again to cancel.
38
JET and LIGHT functions
Each time the JET (Light) button is is pressed, the
operation status is changed in sequence:
• Under COOLING and HEATING mode:
JETon / LIGHTon
JEToff / LIGHTon
JEToff / LIGHTon
JEToff / LIGHToff
• Under other mode:
LIGHToff
LIGHTon
Note:
Each time the batteries are replaced in the remote
control, the RC is pre-set at Light on.
JET mode
• JET mode is used to start or stop fast cooling or
fast heating.
will display on remote control under this
mode. The appliance will blow at super high fan
speed to cool or heat your room quickly and
effectively.
• In JET mode, you can set temperature and
airflow direction
SLEEP mode
This function gives you a more comfortable
environment for sleep. There are 3 sleep modes
for your choice.
Each time this button is is pressed, the operation
status is changed in sequence:
Note:
• Jet function is not available in 6th Sense, Fan
only, and Dehumidifying mode.
• When switching the mode or changing fan
speed, this function will be canceled
automatically.
LIGHT Function
Press this button to turn on or turn off display light
on indoor unit control panel.
You can press this button to turn off the running
indicator light when the appliance is off.
will display on remote control when front panel
display lights up.
STANDARD SLEEP
6th SENSE SLEEP
SLEEP mode off
DIY SLEEP
STANDARD SLEEP mode
1 will display on remote control during this
mode.
• When you set this mode under COOLING
or DEHUMIDIFYING operation, the
appliance will let the set temperature raise
for 1°C for the first hour and another 1°C for
the second hour, then remain constant.
• When you set this mode under HEATING
operation,the appliance will let the set
temperature lower 1°C for the first hour and
another 1°C for the second hour, then
remain constant.
CLOCK function
You can set clock by pressing CLOCK button, then
using + and – buttons to set the correct time,
press CLOCK button again, the clock is set.
Pressing CLOCK button, signal
blink. Within 5
seconds, the value can be adjusted
+ Press once to raise time setting by 1 minute
– Press once to lower time setting by 1 minute
if continuously press + or – buttons, the number
will change rapidly.
12:00 is the default time to display after inserting
batteries.
6th SENSE SLEEP mode
2 will display on remote control during this
mode.
The appliance will change the set temperature
automatically according to the actual room
temperature
39
DIY SLEEP mode
3 will display on remote control during this
mode.
This mode allows you to set your own sleep
mode.
How to set your own sleep mode
• Under this mode, press SUPER SILENT
button and hold it till the temperature display
blinks, you can see "1 hour" is displayed
under it.
• Use + and – buttons to set your desired
temperature and confirm it by pressing
SUPER SILENT button.
• Then the time will automatically change to
"2 hour" and temperature display keeps
blinking, repeat above operation to set your
desired temperature for hour 3~8.
• Once you confirm the setting for hour 8,
your own sleep mode is set and the remote
control display will go back to previous
setting.
Note: During above operations, if there is no
button pressed within 10s or press "on-off"
button, "mode" button, "timer" button,"clock"
or "sleep" button, it will quit setting status
automatically and display previous setting.
How to check your own sleep mode setting
Follow above operations to enter setting status,
just press SUPER SILENT button continuously to
check the temperature for each hour.
How to change your own sleep mode setting
same as "set your own sleep mode".
Note:
• Fan speed and airflow direction can be adjusted.
• Under FAN only and 6th SENSE mode, this
function is not available.
• Only STANDARD SLEEP is available under
Dehumidifying operation.
40
AUTO CLEAN function
• Pressing this button in COOL or DRY mode,the
icon
is displayed and the AUTO CLEAN
function is set. After turning off the appliance,
the indoor fan will keep running for 10 minutes
to eliminate moisture in indoor unit, thus
creating a healthy, mould-free environment. In
this period, you can press this button to stop
indoor fan directly.
• Pressing this button again cancels AUTO CLEAN
function, indoor unit fan will be off directly after
turning off the appliance.
Note: AUTO CLEAN fucntion is not available in
6th SENSE,FAN only and HEATING mode.
INFO °C function
By pressing this button, you can select to display
the set temperature or room temperature on front
panel.
When the appliance is powered on for the first
time,
will be displayed on remote control and
the set temperature will be displayed on control
panel.
Pressing this button, the icon on remote control
will be changed to
, and the indoor room
temperature will be displayed on control panel. It
will go back to set temperature after 5 seconds or
once receiving other operation signal.
Note: only set temperature is displayed on remote
control.
POWER SAVE & ANTI-FREEZE mode
POWER SAVE mode is available under
COOLING and HEATING operation.
POWER SAVE mode under COOLING
operation
When pressing this button, "SE" will display on
front panel and remote control. The appliance will
automatically adjust the set temperature according
to the actual room temperature to let the room
temperature reach a comfortable temperature
zone (24°C ~ 28°C) as quickly as possible. This
mode consumes less energy but still gives you the
comfortable cool.
operate keeping a constant temperature of 8°C
when you are not at home, or in your chalet during
winter time not to let water tubes freeze. When
you are back home, you will not feel so cold, and
don't need to wait for a long time to get the warm
room environment after back to HEATING
operation.
Change mode or press the power save button
again to cancel this function.
POWER SAVE mode under HEATING
operation: ANTI-FREEZE
When pressing this button,
will display on
remote control, temperature is set at 8°C. This
function is designed for areas with very cold winter.
You can set this function to let the appliance
Note: Fan speed and temperature can not be
adjusted under this mode.
41
TIMER function
The T-On/T-Off button allows you to set TIMER
ON function and TIMER OFF function separately.
It is convenient to set the timer on by pressing the
left side of this button to achieve a comfortable
room temperature at the time you get home. You
can also set timer off automatically to enjoy a good
sleep at night by pressing right side of this button.
How to set TIMER ON
TIMER ON button can be used to set the timer
programming as wished in order to switch on the
appliance at your desired time.
I) Press the left side of T-On/T-Off button, icon
will conceal, "ON " flashes on the LCD,
within 5 seconds, you can press the + or –
buttons to select your desired time for appliance
on.
+ Press once to raise time setting by 1 minute
– Press once to lower time setting by 1 minute
if continuously press + or – buttons, the number
will change rapidly.
Note: If you don't set the time in 5 seconds after
you press the button, the remote control will exit
the TIMER ON mode automatically.
II) When your desired time is displayed on remote
control, press the press the left side of T-On/TOff button to confirm it. A "beep" can be heard"
and "ON" indicator stops flashing.
TIMER ON
How to cancel TIMER ON
Press the left side of T-On/T-Off button again, a
"beep" can be heard and the "ON" indicator
disappears, this function has been canceled.
How to set TIMER OFF
TIMER OFF setting is similar to TIMER ON setting,
press the right side of T-On/T-Off button to set
TIMER OFF. You can make the appliance switch off
automatically at your desired time.
+ Increase
– Decrease
Note: Make sure the clock is set correctly before
doing the timer on and timer off setting.
42
TIMER OFF
SUPER SILENT function
Press this button to let the unit operating with low
noise to get a quiet and comfortable room
environment.
will display on remote control and symbol
will be displayed on indoor unit during SUPER
SILENT mode.
Note: this function is only available when the
product is off. Front panel temperature display will
change accordingly when turning on the appliance.
Factory setting is based on °C.
EMERGENCY OPERATION
Under emergency situation or when remote
control is missing, you can control the unit by
pressing the on/off swith located on the indoor
unit.
• Turn on the appliance: when the unit is off, press
this button, it will start up and operate in 6th
SENSE mode.
• Turn off the appliance: when the unit is on, press
this button, the unit will stop working.
Note: Super silent function will be off when
pressing FAN button.
CHILD LOCK function
Press + and – buttons simultaneously to lock or
unlock the buttons of remote control.
If the remote control is locked, icon
will be
displayed, and no functions can be activated by
pressing buttons.
Press + and – buttons simultaneously again to
unlock it.
Switch between °C and °F
After pressing On/Off button to turn off the
appliance, you can press MODE and – buttons
simultaneously to switch between °C and °F.
on/off switch
PROTECTION
Operating condition
The protective device may trip and stop the
appliance in the cases listed below.
seconds may occur before it starts to operate. If all
operation has stopped, press ON/OFF button
again to restart. Timer should be set again if it has
been cancelled.
Outdoor air temperature is over 24°C
Outdoor air temperature is below -7°C
Room temperature is over 27°C
Outdoor air temperature is over *43°C
Cooling
Room temperature is below 21°C
Dehumidifying Room temperature is below 18°C
Heating
Features of COOLING mode
Anti-freezing
When the temperature of the indoor heat
exchanger drops to 0° or below, compressor will
stop working to protect the appliance.
Noise pollution
• Install the appliance at a place that can bear its
weight in order to operate more quietly.
• Install the outdoor unit at a place where the air
discharged and the operation noise would not
disturb your neighbours.
• Do not place any obstacles in front of the air
outlet of the outdoor unit lest it increases the
noise level.
Features of HEATING mode
Preheating
In order to prevent cool air blowing, 2-5 minutes
are necessary to preheat the indoor unit at
HEATING operation start. The indoor fan will not
work during preheating.
Defrosting
In HEATING operation the appliance will defrost
(de-ice) automatically to raise efficiency. This
procedure usually lasts 6-10 minutes. During
defrosting, fan stops running and "H1" will display
on front panel.
After defrosting is completeed, it returns to
HEATING mode automatically.
Features of protection device
Wait at least 3 minutes before restarting the unit
after operation stops or changing mode during
operation. After connecting to power supply and
turning on the appliance immediately, a delay of 20
43
MAINTENANCE
Clean front panel of Indoor Unit
1. Disconnect from the power supply
Turn off the appliance first before disconnecting
from power supply.
2. Remove the front panel
Open the front panel as shown by the arrow
(Fig. A).
Pull the slots at the side of the front panel with
force to take out the front panel (Fig. B).
3. Clean the front panel
Wipe it with a soft and dry cloth. Use lukewarm
water (below 40°C) to clean if the appliance is very
dirty. After cleaning let it dry.
4. Refit and close the front panel.
Refit and close the front panel by pushing it
downward.
Fig. A
Note:
• Do not use substances such as gasoline or
polishing powder to clean the appliance.
• Do not sprinkle water onto the indoor unit
Dangerous! Electric shock!
Fig. B
Clean Air filter
It is necessary to clean the air filter after using it for
about 100 hours.Clean the air filter every two weeks if
the air conditioner operates in an extremely dusty
environment.
1. Disconnect from the power supply
Turn off the appliance first before disconnecting
from power supply.
2. Take out air filter (Fig. C).
1. Open the front panel.
2. Press the handle of the filter gently.
3. Slide out the filter.
3. Cleaning the air filter (Fig. D)
If the filter is very dirty, clean it with a solution of
lukewarm water and neutral detergent.
After cleaning let it dry.
4. Refit the filter and close the front panel.
Fig. C
Note:
• To avoid injury, do not touch the fins of indoor
unit with your fingers after removing the filter.
• Do not attempt to clean the inside of the air
conditioner by yourself.
• Do not clean the filter in washing machine.
• Extra filters:
Your product also has a HEPA filter and a 3 in 1
combo filter. These filters remove small particles,
neutralizes viruses and allergens and eliminates
odours. To maintain the efficiency of the filters, we
advise you to replace these filters every 2-3 years
by contacting a Whirlpool Authorized Service
Centre.
Fig. D
44
TROUBLESHOOTING
Operation problems are often due to minor causes, please check and refer to the
following chart before contacting the service. This may save time and unnecessary
expenses.
Problem
Does not work
Troubleshooting
•
•
•
•
•
•
Is there a power failure?
Is the protection device trip or fuse blown?
Is the plug loose in the socket?
Is the remote control working normally?
Check if you have set the Timer Off function.
Please wait for 3 minutes and start again, protection device may be preventing
• Are the intakes and outlets of the indoor or outdoor unit blocked?
• Is the temperature set properly?
No air blows out of • Indoor fan will not work to prevent blowing of cold air for the first several
minutes when heating process starts.
indoor unit.
• In heating mode, indoor fan will stop air blowing during defrosting.
• In dehumidify mode, the fan on the indoor unit may stop to prevent evaporation
of condensing water and rise of temperature.
Can not adjust
• Is the appliance operating under 6th Sense or Power Save mode? Temperature
temperature setting
can not be adjusted under these modes.
Can not adjust Fan
speed
• Is the appliance operating under dehumidifying or power save mode? Fan speed
can not be adjusted under these modes.
Ineffective control
• Has there been a strong interference (from excessive static electricity discharge,
power supply voltage abnormality)? Note that operation will be abnormal, in this
case unplug from the power supply and re-plug after 2-3 seconds.
Does not operate
immediately
• 3 minute delay will occur when changing mode during operation.
Peculiar smell
• This smell may come from another source such as furniture, cigarette etc, which
is sucked in the unit and blown out with the air.
• Check the air filter if they are very dirty and clean it.
A sound of running
water
• Normal behaviour caused by the flow of refrigerant in the air conditioner.
• Defrosting sound in heating mode.
Cracking sound
• The sound may be generated by the expansion or contraction of the front panel
due to temperature changes.
Mist sprays from
the outlet
• Mist is present in the room with low temperature. Normal behaviour due to
cool air discharged from indoor unit during COOLING or DRY operation
mode.
Remote control
doesn't work
• Is the remote control in range and not blocked by any obstacles?
• Check the battery in the remote control. If low, replace the battery.
• Check the remote control for damage.
Error code is
indicated
• If error code such as E2, E4, E5, E6, F1, F2 F3, F4, F5, H3, H4, H5, HC, L9, LP,
PL, PH, appears on the indoor unit display, turn of the appliance and disconnect
from power supply, then contact the nearest Whirlpool Authorized Service
Center. (H1 and SE is not error code, H1 is the indicator of defrosting during
heating, SE is the indicator of power save function).
Note: If the problems still have, turn off the appliance and disconnect from power supply,
then contact the nearest Whirlpool Authorized Service Center. Do not attempt to move,
repair, disassemble, or modify the appliance by yourself.
45
INSTALLATION SERVICE
Before installation
1. Please read this manual carefully before
installation.
2. The appliance must be installed according to
national wiring rules and according to this
manual by qualified technicians.
3. Any change of installation position must be
handled by professionals;
4. Check the product to verify that it has not been
damaged before installation.
5. Mount with the lowest moving parts of indoor
unit at least 2.5 m above floor or grade Level.
6. After installing, the consumer must operate the
appliance correctly according to this manual,
keep a suitable storage for maintenance and
move of it in the future.
SAFETY PRECAUTION
1. The power supply must be of rated voltage
with special circuitry for the appliance. The
normal operating range of voltage is
90%~110% of rated voltage. The diameter of
the power cord must comply with
requirements.
2. The user power supply shall have a reliable
grounding terminal. It is prohibited to connect
the grounding wire to the following items: 1)
Water Supply Pipe 2) Gas Pipe 3) Sewage Pipe
4) Other positions that are considered unsafe
3. Ensure safe grounding and a grounding wire
connected with the special grounding system of
the building, installed by professionals. The
appliance must be fitted with electrical leakage
protection switch and an air switch with
sufficient capacity (Refer to the following
chart). The air switch must also have a
magnetic and a thermal tripping function to
ensure protection in case of short-circuit and
overload.
Model
Required Capacity of air break
switch
9k
12k
16A
16A
5. If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person in order to
avoid a hazard.
6. An all-pole disconnection switch having a
contact separation of at least 3mm in all poles
should be connected in fixed wiring.
7. Risk of electric shock can cause injury or death:
Disconnect all electric power supplies before
servicing.
8. The connection of power cord and the cable
connection between indoor unit and outdoor
unit shall be in accordance with the wiring
diagram attached on the appliance.
9. Once installation is completed, the electric
components must not be accessible to the
users.
10. Use two or more people to move and install
the appliance to avoid excessive weight hazard.
11. After unpacking the air conditioner, keep all
packaging materials well out of the reach of
children.
12. According to the character of refrigerant
(R410a), the pressure of the tube is very high,
so be sure to careful when you install and
repair the appliance.
4. Make sure that the power supply cord is long
enough to allow the right connection. Do not
use any extension cord for power supply.
46
INSTALLATION INSTRUCTIONS
Installation diagram
Distance from ceiling
should be over 150mm
Distance from wall
should be over 150mm
Distance from the wall
should be over 150mm
Indoor unit
Distance from floor
should be over 2500mm
Outdoor unit
Air intake distance from
the wall should be over
300mm
Air intake distance from
the wall should be over
300mm
A
sho ir ou
uld tlet
be dist
ove anc
r 2 e fr
000 om
mm th
ew
all
Over 500mm
NOTE: The figure above is only a simple presentation of the unit, it may not match the external
appearance of the product you purchased. Installation must be performed in accordance with the national
wiring standards by authorized service people only.
47
Select the best location
Location for Installing Indoor Unit
• Where there is no obstacle near the air outlet
and air can be easily blown to every corner of
room.
• Where piping and wall hole can be easily
arranged.
• Observe the required distance from ceiling and
wall according to the installation diagram.
• Where the air filter can easily be removed.
• Keep the unit and remote control 1m or more
from television, radio etc.
• To prevent the effects of a fluorescent lamp,
keep the unit as far as possible from it.
• Do not put anything near the air inlet that could
obstruct it.
• In a place that can bear the weight and will not
increase operating noise and vibrations.
• The indoor unit is not suitable to be installed in
areas used for laundry.
Indoor unit
Height should
be less than 5m
Pipe length is
5~15 meters
Location for Installing Outdoor Unit
• Install in a convenient and well-ventilated place.
• Avoid installing it where flammable gas could
leak.
• Observe the required distance from the wall
according to the installation diagram.
• The distance between Indoor and outdoor unit
should be 5 meters and can go up to maximum
15 meters with additional refrigerant charge.
• Do not install the outdoor unit in a dirty or
greasy place, near a vulcanization gas exit.
• Avoid installing it at the roadside where it could
be soiled with muddy water.
• A fixed base where operating noise will not
increase.
• Where the air outlet is not obstructed.
• The installation position shall be able to
withstand the weight and vibration of the
outdoor unit and ensure safe installation;
• Where drained water does not become any
problem.
Outdoor unit
Outdoor unit
Height should be less
than 5m
Pipe length is
5~15 meters
Indoor unit
Model
Standard tubing
Length (m)
Limit of Tubing
Length (m)
9K/12K
5
15
Limit of Elevation
Required extra
Difference H (m) refrigerant when the
connecting tube over
5m (g/m)
5
48
20
INDOOR UNIT INSTALLATION
1. Installing the Mounting Plate
• Select a location to install the mounting plate
according to the indoor unit location and piping
direction.
• Adjust the mounting plate horizontally with a
gradienter or plumb line.
• Drill holes 32mm in deep on the wall to fix the
plate.
• Insert the plastic plugs in the hole, then fix the
mounting plate with tapping screws.
• Check that the mounting plate is well fixed.
Then drill a hole for piping.
Mark on the middle
Gradienter
NOTE: The shape of your mounting plate may be different from the one above, but installation method is
similar.
Wall hole sleeve
(hard polythene tube
prepared by user)
Outdoor
Indoor
2. Drill a Hole for Piping
• Decide the position of the hole for piping
according to the location of mounting plate.
• Drill a hole on the wall. The hole should slightly
be inclined downward toward outside.
• Install a sleeve through the wall hole to keep the
wall tidy and clean.
5mm
(downward
inclination)
3. Indoor Unit Piping Installation
• Fit the piping (liquid and gas pipe) and cables
through the wall hole from outside or fit them
from inside after completing indoor piping and
cables connections so as to connect to outdoor unit.
• Decide whether saw off the plastic part in accordance with the piping direction (as shown below).
Piping direction
trough
4
Unloading
piece
Saw the unloading piece off
along the trough
1
3
2
NOTE:
When fixing the pipe along directions 1, 2 or 4, saw the corresponding plastic part off the indoor unit base.
• After connecting the piping as required, install the drain hose. Then connect the power connecting
cable. After connecting, wrap the piping, cable and drain hose together with thermal insulating
materials.
NOTE: Do not connect to power supply during installation.
49
IMPORTANT:
Piping Joints Thermal Insulation:
Wrap the piping joints with thermal insulating materials and then wrap with a vinyl tape.
Wrapped with vinyl type
Thermal insulation
Thermal Insulation piping:
a. Place the drain hose under the piping.
b. Insulation material: polythene foam over 6mm in
thickness.
Large pipe
Thermally
insulated tube
Power connecting
cable
NOTE: Drain hose is prepared by user.
• Drain hose should point downward for easy
drain flow. Do not twist the drain pipe, leave it
sticking out or waving around, do not immerse
the end in water. If an extension drain hose is
connected to the drain pipe, make sure to be
thermally insulated when passing it through the
indoor unit.
• When the piping is directed to the right, piping,
power cable and drain hose should be thermally
insulated and fixed at the rear of the unit.
Small pipe
Drain hose
(prepared by user)
Piping Connection:
a. Connect indoor unit pipes with two wrenches.
Pay special attention to the torque allowed as
shown below to prevent the pipes, connectors
and flare nuts from being deformed and
damaged.
b. At first fingers-tighten them, then use the
wrenches.
Pipe size
Torque
Nut width
Min. thickness
Liquid Side (1/4 inch)
1.5~2kg.m
17mm
0.5mm
Gas Side (3/8 inch)
3.1~3.5kg.m
22mm
0.7mm
Gas Side (1/2 inch)
5.0~5.5kg.m
24mm
0.8mm
Gas Side (5/8 inch)
6.0~6.5kg.m
27mm
0.8mm
50
4. Connecting the Cable
• Indoor Unit
1) Open the front panel, remove the covering
plate by loosening the screw.
2) Connect the power connecting cord to the
indoor unit by connecting the wires to the
terminals on the control board individually as
follows.
3) Secure the power connecting cord on the
control board with cable clamp.
4) Refit the covering plate and tighten the screw.
Covering plate
Blue
Black
Yellow
-Green
Brown
NOTE: (depending on the model)
It is necessary to remove the cabinet to perform
connections with the indoor unit terminal.
Cable Clamp
• Outdoor Unit
1) Remove the access door from the unit by
loosening the screw. Connect the wires to
the terminals on the control board individually
in accordance with the indoor unit
connection.
2) Secure the power connecting cord on the
control board with cable clamp.
3) Refit the access door in the original
position and tighten the screw.
Power
connection
cable
access door
Blue
Black
Cable Clamp
Yellow-Green
Brown
Power
connection
cable
CAUTION:
1. Make sure that the colour of wires and the terminal number of the outdoor unit are the same as those
of the indoor unit.
2. Use an individual power circuit specifically for the air conditioner. As for the wiring method, refer to
the circuit diagram on the appliance.
3. Check that the cable specification conforms to the table as follows.
4. Check the wires and make sure that they are all tightly fastened after cable connection.
The cable should be tighly fastened by cable clamp.
5. Be sure to install an earth leakage circuit breaker in a wet or moist area.
Cable Specifications
Type
Capacity
(Btu/h)
Power cord
Power connecting cable
Main power
supply (Note)
9k
H05VV-F, 3G 1.5 mm²
H07RN-F, 4G 1.5 mm²
To indoor
12k
H05VV-F, 3G 1.5 mm²
H07RN-F, 4G 1.5 mm²
To indoor
Inverter
51
OUTDOOR UNIT INSTALLATION
1. Install Drain Port and Drain Hose
The condensate drains from the outdoor unit when
the unit operates in heating mode. In order not to
disturb your neighbours and protect the
environment, install a drain port and a drain hose to
direct the condensate water. Just install the drain
port on the chassis of the outdoor unit, then
connect a drain hose to the port as shown in the
figure on the right .
2. Install and Fix Outdoor Unit
Chassis
Fix with bolts and nuts tightly on a flat and strong
Drain port
floor. If installed on the wall or roof, make sure to
fix the supporter well to prevent it from shaking due
to serious vibration or strong wind.
Drain hose
(prepare by user)
3. Outdoor Unit Piping Connection
• Remove the valve caps from the 2-way and 3-way valve.
• Connect the pipes to the 2-way and 3-way valves separately according to the required torque.
4. Outdoor Unit Cable Connection (see previous page)
52
AIR PURGING
Air containing moisture remaining in the refrigeration cycle may cause a malfunction on the compressor.
After connecting the indoor and outdoor units, evacuate air and moisture from refrigerant cycle using a
vacuum pump, as shown below.
Note: Because the system pressure is high and also to protect the environment, be sure not to discharge
the refrigerant to the air directly.
Connect to indoor unit
3-way valve diagram
Open position
Vacuum pump
Connect to outdoor unit
Spindle
Needle
r unit
Indoo
Service port cap
Refrigerant flow direction
2-way valve
Valve core
3-way valve
(6) Open 1/4 turn
(7) Turn to fully open the valve
(7) Turn to fully
open the valve
Valve cap
(1) Turn
Service port
(1) Turn
(8) Tighten
(8) Tighten
(2) Turn
(8) Tighten
Valve cap
How to Purge Air Tubes:
1. Unscrew and remove caps from 2 and 3-way valves.
2. Unscrew and remove cap from service valve.
3. Connect vacuum pump flexible hose to the service valve.
4. Start vacuum pump for 10-15 minutes until it reaches an absolute vacuum of 10 mm Hg.
5. With vacuum pump still running close the low pressure knob on vacuum pump manifold. Then stop
vacuum pump.
6. Open 2-way valve 1/4 turn, then close it after 10 seconds. Check tightness of all joints using liquid soap
or an electronic leak detector.
7. Turn 2 and 3-way valves stem. Disconnect vacuum pump flexible hose.
8. Replace and tighten all valve caps.
53
Download PDF

advertising