Privileg PWT 2505 Instruction for Use

CONTENTS
DEFINITION OF USE
BEFORE USING THE WASHING MACHINE
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE
INSTALLATION
ELECTRICAL CONNECTION
BEFORE THE FIRST WASH CYCLE
PREPARATION OF THE LAUNDRY
DETERGENTS AND ADDITIVES
CLEANING THE FILTER/
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
TRANSPORT AND HANDLING
DEFINITION OF USE
This washing machine is exclusively destined to wash
and spin machine washable laundry in quantities which
are usual for private households.
• Observe the instructions given in these Instructions
for Use and the Programme Chart when using the
washing machine.
• Keep these Instructions for Use and the
Programme Chart; if you pass on the washing
machine to another person, also give him/her
Instructions for Use and Programme Chart.
BEFORE USING THE WASHING MACHINE
1. Remove the packaging and check
• Pressure: 100-1000 kPa (1-10 bar).
• Only use new hoses for connecting the washing
machine to the water supply. Used hoses must
not be used anymore and should be discarded.
a. Cut and remove the shrink-wrap.
b. Remove the top protection and the protective
corners.
c. Remove the bottom protection by tilting
and turning the washing machine on one
rear bottom corner. Make sure that the
black plastic part of the bottom protection
(if available on the model) remains in the
packing and not in the machine bottom.
This is important, as otherwise the plastic part could
damage the washing machine during operation.
d. Open the lid by pressing it slightly down while
raising the handle. Remove the polystyrene
cushion (depending on model).
e. Remove the blue protective film from the panel
(depending on model).
• After unpacking, make sure that the washing machine
is undamaged. If in doubt, do not use the washing
machine. Contact After-Sales Service or your local
retailer.
• Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children;
they are potentially dangerous.
• If the appliance was exposed to the cold prior to
delivery, keep it at room temperature for a few
hours before operating.
5. Drain hose
• Connect the drain hose to the siphon or hook it
over the edge of a sink with the “U” bend (see
“Installation”/“Connect the water drain hose”).
• If the washing machine is connected to a built-in
drainage system, ensure the latter is equipped
with a vent to avoid simultaneous loading and
draining of water (siphoning effect).
6. Electrical connection
• Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and the current
standard safety regulations.
• The technical data (voltage, power and fuses) are
given on the rating plate on the rear of the washing
machine.
• The washing machine must be connected exclusively
by means of a socket with an earth connection in
accordance with current regulations. The washing
machine must be earthed by law. The manufacturer
declines all liability for injury to persons or animals or
damage to property deriving directly or indirectly
from failure to observe the directions.
• Do not use extension leads or multi sockets.
• Before any maintenance on the washing machine
disconnect it from the mains supply.
• Access to the mains plug or to disconnection from
the mains supply via a double-pole switch must be
ensured at all times following the installation.
• Do not operate the washing machine if it has been
damaged during transport. Inform the After-Sales
Service.
• Mains cable replacement is only to be carried out
by After-Sales Service.
• The washing machine must be connected to an
effective earthing installation, in compliance with the
regulations in force. In particular, washing machines
installed in premises containing a shower or a bath
must be protected by a differential residual current
device of at least 30 mA. Earthing the washing
machine is obligatory under the law. The
manufacturer declines all liability for injury to persons
or animals or damage to property deriving either
directly or indirectly from failure to observe the
directions in these Instructions for Use.
• The washing machine may only be used in the
household for the prescribed uses.
Dimensions:
Width:
400 mm
Height:
900 mm
Depth:
600 mm
2. Remove the transport bracket
• The washing machine is fitted with transport
screws and a transport bracket to prevent
damage during transport. Before using the
washing machine you must remove the
transport bracket (see “Installation”/“Removal
of transport bracket”).
3. Install the washing machine
• Place the washing machine on a flat and stable
floor surface.
• Adjust the feet to ensure that the machine is
stable and level (see “Installation”/“Adjust the
feet”).
• In case of wooden or so-called “floating floors”
(for instance certain parquet or laminate floors),
place the appliance on a 40 x 60 cm sheet of
plywood at least 3 cm in thickness which is
secured to the floor.
• Make sure that the ventilation openings in the
base of your washing machine (if available on
your model) are not obstructed by a carpet or
other material.
4. Water supply
• Connect the water supply inlet hose in
accordance with the regulations of your local
water company (see “Installation”/“Connect the
water inlet hose”).
• Water supply: Cold water only
• Tap: 3/4” threaded hose connection
GB 2
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
1. Safety instructions
• The symbol
on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as
household waste. Instead it shall be handed over
to the applicable collection point for the recycling
of electrical and electronic equipment.
Disposal must be carried out in accordance with
local environmental regulations for waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where you
purchased the product.
• The washing machine is built from reusable
materials. It must be disposed of in compliance
with current local waste disposal regulations.
• Before scrapping, cut off the power cable so that the
washing machine cannot be connected to the mains.
• Remove detergent from compartment if you
intend scrapping your washing machine.
• The washing machine is appropriate for indoor
use only.
• Do not store flammable fluids near the appliance.
• Do not place electrical appliances on the lid of
your washing machine.
• Children must be supervised to ensure that they
do not play with the appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
• Do not attempt to force the lid open.
• If necessary, the power cable may be replaced
with an identical one obtained from our AfterSales Service. The power cable must only be
replaced by a qualified technician.
• The Manufacturer is not liable for any damage to
laundry resulting from inadequate or incorrect
fabric care instructions which have been
provided with the garment or article.
4. General recommendations
• Do not leave the washing machine connected
when not in use. Turn off the tap.
• Before cleaning or carrying out maintenance
switch off the washing machine and disconnect it
from the mains supply.
2. Packing
• The packaging materials are 100% recyclable and
bear the recycling symbol
. Adhere to local
regulations when disposing of packaging material
5. EC Declaration of Conformity
3. Disposing of packaging and old washing
machines
• This washing machine has been designed,
constructed and distributed in compliance with
the safety requirements of EC Directives:
2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility
Directive
• This appliance is marked according to the
European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
DESCRIPTION OF THE WASHING MACHINE
1. Lid
2. Detergent dispenser
1
3. Drum
2
4. Pump access behind filter
3
5. After-Sales Service sticker (behind the
filter cover)
6. Mobility lever (depending on model)
• To move the washing machine: pull
the handle out a little bit by hand and
pull it out to the stop with the foot.
7. Adjustable feet
4
GB 3
7
6
5
7
INSTALLATION
Removal of transport bracket
The washing machine is fitted with a transport bracket to
avoid any possible damage during transport.
IMPORTANT: Before using the washing machine, the
transport bracket at the back MUST be removed.
A
B
1. Unscrew the two screws “A” and the four screws “B”
with a flat screwdriver or a No. 8 hex nut box spanner.
2. Remove the transport bracket.
3. Replace the four outer screws “B” on the machine and
tighten them.
4. Clip the two seals “C” supplied into the openings “D” of
the washing machine.
1\3
Note: do not forget to replace and tighten the four outer
screws.
2
C
D
Adjust the feet
Install the washing machine on a level surface, near to
electrical, water and drain connections.
If the floor is uneven, adjust the feet (do not insert pieces
of wood, cardboard etc. under the feet):
1. Loosen the locknut using the wrench provided.
2. Adjust the height of the feet by hand.
3. Retighten the locknut by turning it anti-clockwise.
Make sure that the feet are resting correctly on the
floor and that the washing machine is perfectly level
and stable (use a spirit level).
The washing machine can be installed in an area 40 cm wide
and 63 cm deep.
Note: if you install the machine on thick carpet, adjust the
feet to ensure that there is sufficient space under the
machine for the air to circulate.
GB 4
4
Connect the water inlet hose
1. Carefully screw the water inlet hose to the valve on the rear side of
the washing machine (“A”); screw the other end of the hose to the
tap by hand.
A
2. Make sure there are no kinks in the hose.
3. Check water-tightness of tap and washing machine connections by
turning the tap completely on.
If the hose is too short, replace it with a suitable hose available through
our After-Sales Service or your specialist retailer.
Periodically check the hose for brittleness and cracks. Replace it if
necessary by a new hose available through our After-Sales Service or
your specialist retailer.
The washing machine can be connected without a non-return valve.
Water stop anti-flooding system
(see inlet hose type as shown on the right - depending on model)
• Screw the hose to the water supply tap. Turn the tap fully on and
check the water-tightness of the connection.
• The washing machine must not be connected to the mixing tap of a
non-pressurized water heater!
• The inlet hose and the plastic enclosure contain (depending on
model) electrical components: do not cut the hose and do not
immerse the enclosure in water.
• If the flexible hose is damaged, unplug the washing machine from
the mains immediately, turn off the tap and replace the hose.
If the flexible hose is too short, replace it with a 3 m Water Stop hose
(available from After-Sales Service or from your dealer).
Connect the water drain hose
1. Unhook the drain hose from the left clip, see arrow “A” on picture.
Important:
Do NOT loosen the drain hose from the right connection, see
arrow “B” on picture. Otherwise, there is the risk of leakage and of
scalding with hot water.
A
2. Fix the “U” bend (“C”) at the very end of the drain hose.
3. Connect the drain hose to the siphon or hook it over the edge of a
sink with the “U” bend and fix it properly.
Small hand basins are not suitable.
The edge of the sink must be no more than 100 cm from the floor.
If you need to add an extension, use a flexible hose of the same size
and secure the unions with screw-on hose clips.
Maximum overall drain hose length: 2.50 m.
Maximum drain height (“U” bend): 100 cm.
Minimum drain height: 55 cm.
Important:
Make sure there are no kinks in the drain hose and take precautions
against it falling while the washing machine is running.
GB 5
B
C
ELECTRICAL CONNECTION
Do not use extension leads or multi sockets.
Electrical connections must be made in accordance with local regulations.
1) Warning - this washing machine must be earthed
This washing machine is normally supplied with a mains lead having a plug fitted in the factory which has
been checked for correct earth continuity.
If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with a plug,
you should fit a suitable new, good quality plug by following the instructions in (2) below.
Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it be
inserted into a socket.
2) CONNECTION TO A REWIRABLE PLUG - to be carried out only by a qualified electrician
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)
To fit a new plug, proceed as follows:
2.1) Polarized Plugs (e.g. 3 pin, 13 amp plug conforming to
BS 1363A)
a. The GREEN AND YELLOW wire must be connected to the
terminal in the plug which is marked with the letter “E” or by
the Earth symbol
or coloured green and yellow.
b. The BLUE wire must be connected to the terminal which is
marked with the letter “N” or coloured blue.
c.
The BROWN wire must be connected to the terminal
which is marked with the letter “L” or coloured brown.
2.2) Non-polarized plugs (e.g. 2 pin with side earth contact)
The wire which is coloured GREEN AND YELLOW must be connected to the earth contact. The other two
wires should be connected to the two pins, irrespective of colour.
FUSE REPLACEMENT
If the mains lead of this washing machine is fitted with a BS 1363A
13 amp fused plug, replace the fuse only with an A.S.T.A. approved type
conforming to BS 1362 and proceed as follows:
Remove the fuse cover (A) and the fuse (B).
Fit the replacement 13 A fuse into the fuse cover.
Refit both into the plug.
For all other types of plug, the supply socket should be protected by
a 16 A fuse or circuit breaker at the distribution board.
GB 6
BEFORE THE FIRST WASH CYCLE
To remove any residual water used in testing by the manufacturer, we recommend that you carry out a
short wash cycle without laundry.
1. Open the tap.
2. Close the drum flaps.
3. Add a small amount of detergent (maximum 1/3 of the quantity the detergent manufacturer
recommends for lightly soiled laundry) to the main wash chamber
of the detergent dispenser.
4. Close the lid.
5. Select and start programme “Synthetics” at 60°C (see separate the programme chart).
PREPARATION OF THE LAUNDRY
Sort the laundry
2. Empty pockets
Coins, safety pins and similar items can damage
your laundry as well as the washing machine’s
drum and tub.
1. Sort the laundry according to…
• Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics,
wool, handwash items.
3. Fasteners
Close zips and fasten buttons or hooks; loose
belts or ribbons should be tied together.
• Colour
Separate whites and coloureds.
Wash new coloured items separately.
Stain removal
• Blood, milk, egg and other organic substances are
generally removed by the enzyme phase of the
programme.
• To remove red wine, coffee, tea, grass and fruit
stains etc. add a stain remover to the main wash
chamber of the detergent dispenser.
• Particularly stubborn stains should be treated
before the wash.
• Size
Wash items of different sizes in the same load to
improve washing efficiency and distribution in the
drum.
• Fabric delicacy
Wash delicate articles separately: use a special
programme for Pure New Wool
, curtains
and other delicates. Always remove curtain glides
or wash curtains with the glides inside a cotton
bag. Use the special programme for handwash
fabrics. Wash stockings, belts and other small
items or articles with hooks (e.g. bras) in special
cotton bags for washing machines or in zipped
pillow cases.
Dyeing and bleaching
• Only use dyes and bleaches that are suitable for
washing machines.
• Follow the manufacturer’s instructions.
• Plastic and rubber parts of the machine may be
stained by dyes or bleaches.
GB 7
Loading the laundry
1. Open the machine lid by pulling it upwards.
2. Open the drum
- by pushing the drum flap release (for “1a”
and “1b”; models as shown on “1a” have
a fixed drum flap release which will not
compress when pushed).
- by holding the rear drum flap, sliding back
the slider into arrow direction and pushing
the front flap towards the inside of the drum
until the closing mechanism releases (for “1c”).
1a
1b
3. Place the items of laundry into the drum one
by one. Do not exceed the maximum load
of the programmes indicated in the separate
programme chart.
- Overloading the machine will result in
unsatisfactory washing results and creased
laundry.
1c
- Take care that the laundry does not
overhang the drum; if this is the case, push
the laundry down into the drum so that
there is enough free space to close the
drum flaps properly.
- Do not use the flaps to push the laundry
into the drum.
4. To close the drum, hold both flaps in the
middle again (picture “2”), the rear flap over
the front flap.
ATTENTION: make sure that the drum
flaps are properly locked - depending on the
model:
2
- the metal hook must be completely
hooked into the rear door flap - see picture
“2a”, or
- all metal hooks must be properly hooked
inside the rear door flap, and the button
must overlap the edge of the rear door flap
- see picture “2b”.
2a
- the slider of the front flap must slightly
overlap the rear flap - see picture “2c”.
2b
Check that no laundry gets stuck between the flaps,
or between flaps and drum.
2c
GB 8
DETERGENTS AND ADDITIVES
Choice of the right detergents and
additives:
Dosage
Follow the instructions on the detergent pack in
relation to:
- The degree and type of soiling.
- The size of the load.
Full load: follow the detergent
manufacturer’s instructions;
Half load: 3/4 the amount used for a full
load;
Minimum load (about 1 kg): half the
amount used for a full load
- Water hardness in your area (ask for
information from your water company): soft
water requires less detergent than hard water.
The type of detergent depends on:
- Type of fabric (cottons, easy care/synthetics,
delicate items, wool).
- Colour.
- Washing temperature.
- Degree and type of soiling.
• Use only specific detergents for wool and
garments made of microfibres (like sports or
swimwear).
• Do not use liquid detergents when activating the
“Start delay” function (if available on your
machine).
• Do not use liquid detergent for the main wash
when activating the “Prewash” option or
selecting a programme with “Prewash” (if
available on your model).
• Whitish residues on dark fabrics are caused by
insoluble detergents components used in
modern phosphate-free powder detergents. If
you notice this problem, shake or brush the
affected items or use liquid detergents.
• Keep detergents and additives in a safe, dry place
out of the reach of children.
• Use only detergents and additives specifically
produced for domestic washing machines.
• If you use descaling agents, dyes or bleaches,
make sure that they are suitable for washing
machine use.
• Descaler could contain components that can
damage parts of your washing machine.
• Do not use solvents (turpentine, benzine, etc.).
• Do not machine wash fabrics that have been
treated with solvents or flammable liquids.
• Too much detergent can result in excess foam
formation, and the reduction of washing efficiency.
If the washing machine detects excessive foam it
may prevent spinning.
• Insufficient detergent may result in:
grey laundry, deposits on the drum, tub and
heater.
• When using concentrated fabric softeners, add
water in the detergents dispenser up to “MAX”
level mark.
• To prevent dispensing problems when using
highly concentrated powder and liquid
detergents, use the special detergent ball or bag
supplied with the detergent and place it inside
the drum.
(
Where to put detergents and additives
Pour in the detergent:
• Laundry detergent for prewash and main wash
• Laundry detergent for main wash without prewash
• Fabric softeners no more than to “MAX” mark.
• Stain removers
• Water softeners (water hardness class 4)
• Starch (dissolved in water; maximum 100 ml)
Observe the “MAX” level marks for powder detergent
liquid detergent
and fabric softener
.
,
For programmes without prewash and temperatures from cold to
40°C, it is recommended to use liquid detergents to avoid whitish
residues on the laundry.
GB 9
)
Using chlorine bleach
Using starch powder
• Wash your laundry in the desired programme
(Cotton, Synthetics), adding an appropriate
amount of chlorine bleach to the SOFTENER
chamber (close the lid carefully).
• Immediately after end of programme, start the
“Rinse and Spin” programme to eliminate any
residual bleach smell; if you want, you can add
softener.
• Never put both chlorine bleach and softener into
the softener chamber at the same time.
If you want to use starch powder, proceed as follows:
• Wash your laundry in the desired wash programme.
• Prepare the starch solution according to the
starch manufacturer’s instructions.
• Fill the prepared starch solution (maximum
100 ml) into the softener chamber of the
detergent dispenser.
• Close the lid and start programme “Rinse and
Spin”.
CLEANING THE FILTER/
DRAINING RESIDUAL WATER
The washing machine is provided with a self-cleaning
pump. The filter keeps objects like buttons, coins, safetypins
etc. which have been left in the laundry.
We recommend to check and clean the filter regularly, at
least two or three times a year.
Especially:
• if the appliance is not draining properly or if it fails to
perform spin cycles.
• if the “Clean pump” indication lights up.
IMPORTANT: make sure the water has cooled before
draining the appliance.
2
Residual water must be drained also before transporting
the machine.
1. Unplug the washing machine.
2. Open the filter cover with a coin.
3. Place a bowl beneath it.
4. Turn the filter slowly anti-clockwise until the grip is
vertical; do not remove it as yet.
5. Wait until all the water has drained out.
6. Now unscrew the filter completely and extract it.
7. Clean the filter and the filter chamber.
8. Make sure the pump impeller (in the housing behind
the filter) is not obstructed.
9. Insert the filter again and screw it fully down in a
clockwise direction to the stop (until the grip is
horizontal).
10. Pour approximately one litre of water into the washing
machine via the drum and check that water does not
leak from the filter.
11. Close the filter cover.
12. Reconnect the washing machine.
GB 10
6
CARE AND MAINTENANCE
Detergent dispenser
Clean the detergent dispenser regularly, at least three or
four times a year, to prevent detergent build-up:
1. Push in the buttons on each side of the dispenser.
2. Pull the dispenser towards you and remove it.
A small quantity of water can remain in the dispenser. It is
advisable to carry the dispenser in an upright position.
3. Wash the dispenser using running water.
You can also remove the siphon caps in the dispenser for cleaning.
4. Replace the siphon caps in the dispenser (if removed).
Make sure that they lock in place.
5. Replace the dispenser by locating the bottom tabs in the lid
holes and pivot until both of the upper buttons lock.
Note: ensure that the detergent dispenser is correctly
reinstalled.
Water inlet hose filter
Check and clean regularly (at least two or three times a year).
1. Unplug the washing machine.
2. Turn off the tap.
3. Unscrew the hose from the tap.
4. Carefully clean the filter located at the end of hose, without
disassembling it, for example with a tooth-brush.
Note: Do not submerge the hose in water.
5. Screw the flexible hose back onto the tap by hand. Do not use
pliers (risk of squashing the joint).
6. Turn on the tap and check that the connections are
water-tight.
Safety valve
inspection
window
A
7. Plug the washing machine back in.
Water inlet hose (A, B or C, depending on model)
Check regularly for brittleness and cracks. If a inlet hose shows a
damage, replace it by a new hose of the same type, available through
our After-Sales Service or your specialist dealer.
If the inlet hose of your washing machine corresponds with the
model on picture “A”, periodically check the safety valve inspection
window: if it is red, the hose’s waterstop function was triggered, and
the hose must be exchanged by a new one from our After-Sales
Service or your specialist dealer
B
If your supply hose has a transparent hose coating (fig. “B”),
periodically check the colour. If the hose colour intensifies locally,
this is an indication that the hose may have a leak and should be
replaced. Contact our After-Sales Service team or specialist dealer
to obtain a replacement hose.
C
GB 11
Appliance exterior and control panel
Lid seal
• Clean with a soft damp cloth.
• Check the condition of the lid seal periodically
and clean it from time to time with a damp cloth.
• If necessary, a neutral household cleaner can be
applied (do not use aggressive or abrasive products).
Water inlet hose(s)
• Check the hose regularly for brittleness and
cracks. Replace if necessary.
Appliance interior
• After each washing, leave the lid open for some
time to allow the inside of the appliance to dry.
Filter
• If you never or seldom wash your laundry at
95°C, we recommend to occasionally run a 95°C
programme without laundry, adding a small
amount of detergent, to keep the interior of the
appliance clean.
• Check and clean the filter regularly, at least 3 or
4 times a year (see “Cleaning the Filter/ Draining
Residual Water”).
Do not use flammable fluids for cleaning the appliance.
Recovering an object that falls between the drum
and the tub
If an object accidentally falls between the drum and the tub, you
can recover it thanks to one of the removable drum blades:
1. Unplug the washing machine.
2. Remove the laundry from the drum.
3. Close the drum flaps and turn the drum a half-turn.
4. Using a screw-driver, press on the plastic end while sliding
the blade from left to right.
3
5. It will fall into the drum.
6. Open the drum: you can recover the object through the hole
in the drum.
7. Refit the blade from inside the drum:
Position the plastic tip above the hole on the right side of the
drum.
8. Then slide the plastic blade from right to left until it clips.
4
9. Close the drum flaps again, turn the drum through half a turn
and check the positioning of the blade at all its anchorage points.
10. Plug the washing machine in again.
4
7
GB 12
TROUBLESHOOTING GUIDE
Your washing machine is equipped with automatic safety functions which detect and diagnose faults at an early
stage and allow you to react appropriately. These faults are frequently so minor that they can be removed within
a few minutes.
Problem
Causes - Solutions - Tips
Appliance does not start,
no indicator lamps are on
• Plug is not properly inserted in socket.
• Socket or fuse does not function correctly (use a table lamp or similar
appliance to test it).
Appliance does not start
although “Start(Pause)”
has been pressed
• Lid is not properly closed.
• The “Lock buttons” function
has been activated (if available on your
model). To unlock the buttons, push temperature and spin speed button
simultaneously and hold them at least for 3 seconds. The key symbol on
the display disappears and the programme can be started.
Appliance stops during the
programme, and the
“Start(Pause)” light flashes
• “Rinse hold” option is activated (if available on your model) and
(Rinse hold) lights up in the programme sequence indicator terminate “Rinse hold” by pressing “Start(Pause)” or by choosing and
starting “Drain”.
• Programme has been changed - reselect desired programme and press
“Start(Pause)”.
• Programme has been interrupted and eventually lid has been opened close lid and restart programme by pressing “Start(Pause)”.
• The appliance’s safety system has been activated (see “Description of
failure indications”).
• Water tap is not opened or water inlet hose is kinked (“Water tap closed”
indication lights up).
Detergent dispenser
contains residues from
detergent/additives at end
of wash
• Detergent dispenser is not properly installed, or detergent dispenser is
blocked (see “Care and Maintenance”).
• Filter in the water inlet hose is blocked (see “Care and Maintenance”).
Appliance vibrates during
spin cycle
• Washing machine is not level; the feet are not properly adjusted (see
“Installation”).
• The transport bracket has not been removed; before using the washing
machine, the transport bracket must be removed.
Final spin results are poor
The appliance has an imbalance detection and correction system.
If individual heavy items are loaded (e.g. bathrobes), this system may reduce
the spin speed automatically or even interrupt the spin completely in order
to protect the washing machine.
• Heavy items prevented spinning; add smaller articles of laundry and
repeat spin cycle.
• Excessive foam formation prevented spinning; select and start “Rinse &
Spin” programme. Avoid excessive detergent dosing (see “Detergents
and Additives”).
• “Variable spin” button (if available on your model) has been set to a low
spin speed, or “No spin” option (if available on your model) has been
activated.
Programme time is some
longer/shorter than
initially displayed (only for
appliances having a
display which indicates
the remaining
programme time)
Normal capacity of the appliance to adapt to factors that can have an effect
on the wash programme time, e.g.: excess of foam formation, load
imbalance due to heavy items of laundry, prolonged heating time resulting
from reduced inlet water temperature.
Due to such influences, the programme time is recalculated and updated if
necessary. On certain displays (depending on the model), an
animation appears during such update periods.
GB 13
Description of failure indications
Failure indication
lights up
Description - Causes - Solutions
Appliance has no or insufficient water supply. The “Start(Pause)” light flashes.
“Water tap closed”
Check whether:
• Water tap is fully open and water supply pressure is sufficient.
• Kinks are present in water inlet hose.
• Mesh filter of water supply hose is blocked (see “Care and Maintenance”).
• Water hose is frozen up.
• Safety valve inspection window of your water supply hose is red (provided
your appliance has a water supply hose as shown on picture “A” - see
previous chapter “Care and Maintenance”); replace the hose by a new one
available through our After-Sales Service or your specialist dealer.
After problem has been removed, restart programme by pressing “Start
(Pause)”. If the fault occurs again, contact our After-Sales Service (see next
chapter).
“Clean pump”
Waste water is not pumped out. The appliance stops in the corresponding
programme step; unplug it and check whether:
• Kinks are present in the drain hose.
• Filter or pump is blocked (see chapter “Cleaning the Filter/ Draining Residual
Water”; make sure the water has cooled before draining the
appliance).
• The drain hose is frozen up.
After problem has been removed, select and start “Drain” programme or push
“Reset” button for at least 3 seconds; afterwards restart desired programme.
If the fault occurs again, contact our After-Sales-Service (see next chapter).
GB 14
Failure indication
lights up
Indication on display
(if fitted on your
machine)
Appliance stops during the programme.
“bdd”
(in case your washing
machine has no
display: all lamps of the
programme sequence
indicator light up)
“Drum flaps open” (the drum flaps have not been
closed properly).
Push the “Reset”
button for at least 3 seconds
and wait until the “Door open”
lights up.
Open lid and close drum flaps, then select and start
desired programme again. If fault persists, notify our
After-Sales Service.
from “F02” to “F35”
(except “F09”)
“Service”
Description - Causes - Solutions
“Electrical module fault”
Select and start “Drain” programme or push
“Reset” button
for at least 3 seconds.
“F09”
“Water level too high” (after programme
cancellation or false operating). Switch off appliance
and then switch it on again, select programme
“Drain” and start within 15 sec.
“FA”
“Waterstop fault”
Switch off appliance, pull out mains plug and turn
water tap off. Tilt appliance forward carefully to
allow collected water to flow out from the bottom.
Then:
• Plug in the appliance again.
• Turn the water tap on (if water immediately flows
into the appliance without the appliance being
started, there is a failure; turn off the tap and
notify After-Sales Service).
• Select and start the desired programme again.
“Fod”
“Overfoaming”
Too much foam interrupted the wash programme.
• Select and start “Rinse & Spin” programme
.
• Afterwards select and start desired programme
again, using less detergent.
If faults persist, unplug the appliance, turn off the
water tap and contact our After-Sales Service (see
next chapter).
If your washing machine has no time display, check which of the previously described
situations could be the origin of the fault and follow the corresponding instructions.
GB 15
AFTER-SALES SERVICE
Before contacting After-Sales Service:
Specify:
1. Try to remedy the problem yourself (see
“Troubleshooting Guide”).
• The nature of the problem.
• The exact model of the washing machine.
• The service code (number after the word
SERVICE).
2. Restart the programme to check whether the
problem has solved itself.
3. If the machine continues to function incorrectly,
call After-Sales Service.
The After-Sales Service sticker is situated
behind the filter cover or on the rear of the
machine.
• Your full address.
• Your telephone number and area code.
As a priority, you should contact the After-Sales
Service of the retailer who supplied you with the
washing machine.
TRANSPORT AND HANDLING
1. Unplug the washing machine.
2. Turn off the tap.
3. Remove the water supply and drain hose.
4. Eliminate all water from the hoses and the washing machine
(see “Cleaning the Filter/ Draining Residual Water”).
Wait for the water to cool so as to avoid any accidents.
5. To facilitate moving the machine, pull the handle situated at
the bottom front (if available on your model) out a little by
hand and pull it out to the stop with the foot. Afterwards push
the handle back into the original stable position.
6. Fix the transport bracket again for transportation.
7. Transport the washing machine upright.
IMPORTANT: Do not use the washing machine while the handle
is pulled out.
GB 16
5
">