KitchenAid | KHID4 77510 | Instruction for Use | KitchenAid KHID4 77510 Instruction for Use

Instructions for use
Installation diagrams
4
Important safety instructions
6
Safeguarding the environment
9
Declaration of conformity
9
Before use
9
Existing pots and pans
9
Recommended pot bottom widths
9
Installation
10
Electrical connection
10
Instructions for use
12
Cleaning
15
Troubleshooting guide
15
Noises made by the hob
15
After-Sales Service
16
Power level table
16
3
Installation diagrams
180 mm x 230 mm
145 mm
180 mm x 230 mm
210 mm
4
Installation diagrams
770 mm
52 mm
510 mm
0
+1
0
30 mm
750 +2 mm
742 mm
483 mm
R = Min. 6,5 mm
Max. 8 mm
Min. 50 mm
0
490 +2
mm
Min. 10 cm
Min. 5 mm
Min. 3 cm
Max. 6 cm
1
2
X4
3
5
These instructions shall also be available on website: www.kitchenaid.eu
IMPORTANT SAFETY INSTRUCTIONS
YOUR SAFETY AND THAT OF OTHERS IS VERY
IMPORTANT
This manual and the appliance itself provide important safety messages,
to be read and always observed.
This is the danger symbol, regarding safety, warning of potential
risks to users and others.
All safety messages will be preceded by the danger symbol and
the following words:
DANGER
Indicates a hazardous situation which, if
not avoided, will result in serious injury.
WARNING
Indicates a hazardous situation which, if
not avoided, could cause serious injury.
All messages relevant to safety specify the potential risk to which they
refer and indicate how to reduce the risk of injury, damage and electric
shocks due to incorrect use of the appliance.
Make sure to comply with the following:
- Use protective gloves to perform all unpacking and installation
operations.
- The appliance must be disconnected from the power supply before
carrying out any installation operation.
- Installation and maintenance must be carried out by a specialised
technician, in compliance with the manufacturer’s instructions and the
local safety regulations in force. Do not repair or replace any part of
the appliance unless specifically stated in the user manual.
- The appliance must be earthed.
- The power cable must be long enough for connecting the appliance,
fitted in the cabinet, to the power supply.
- For installation to comply with the current safety regulations, an
omnipolar switch with minimum contact gap of 3mm is required.
6
- Do not use multi-sockets or extension cords.
- Do not pull the appliance’s power cable.
- The electrical parts must not be accessible to the user after
installation.
- The appliance is designed solely for domestic use for cooking food.
No other use is permitted (e.g. heating rooms). The Manufacturer
declines any liability for inappropriate use or incorrect setting of the
controls.
- The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Very young (0-3
years) and young children (3-8 years) shall be kept away unless
continuously supervised.
- Children from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge
can use this appliance only if they are supervised or have been given
instructions on safe appliance use and if they understand the hazards
involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
- Do not touch the appliance heating elements during and after use. Do
not allow the appliance to come into contact with cloths or other
flammable materials until all the components have cooled down
completely.
- Do not place flammable materials on or near the appliance.
- Overheated oils and fats catch fire easily. Pay attention when cooking
food products rich in fat and oil.
- A separator panel (not supplied) must be installed in the compartment
under the appliance.
- If the surface is cracked, switch off the appliance to avoid the
possibility of electric shock. (only for appliances with glass surface).
- The appliance is not intended to be operated by means of an external
timer or separate remote control system.
- Unattended cooking on a hob with fat or oil can be dangerous and
may result in fire. NEVER try to extinguish a fire with water, but
switch off the appliance and then cover flame e.g. with a lid or a fire
blanket.
7
Danger of fire: do not store items on the cooking surfaces.
- Do not use steam cleaners.
- Metallic objects such as knives, forks, spoons and lids should not be
placed on the hob surface since they can get hot.
- After use, switch off the hob element by its control and do not rely on
the pan detector. (only for appliances with glass surface).
Disposal of household appliances
- This product is built from recyclable or reusable materials. Disposal must be carried out in accordance
with local regulations for waste disposal. Before scrapping, cut off the power supply cable.
- For further information on the treatment, recovery and recycling of household appliances, contact the
competent local authority, the domestic waste collection service or the shop where you purchased the
product.
8
Safeguarding the environment
Disposal of packing
The packing material is 100% recyclable and
marked with the recycling symbol
. The various
parts of the packing must not be dispersed in the
environment, but disposed of in compliance with
local regulations.
The symbol
on the appliance or the
accompanying documentation indicates that this
product should not be treated as domestic waste but
must be taken to an appropriate collection point for
recycling WEEE.
Disposal
This appliance is marked in conformity with
European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring that this appliance is correctly
disposed of, the user can help prevent potentially
negative consequences for the environment and the
health of people.
Declaration of conformity
Energy saving tips
For optimum results, it is advisable to:
• Use pots and pans with bottom width equal to
that of the cooking zone.
• Only use flat-bottomed pots and pans.
• When possible, keep pot lids on during cooking.
• Use a pressure cooker to to save even more
energy and time.
• Place the pot in the middle of the cooking zone
marked on the hob.
n
This appliance, has been designed, manufactured and marketed in conformity with the safety requirements
of “Low Voltage” Directive 2006/95/EC (replacing 73/23/EEC as amended) and protection requirements of
“EMC” Directive 2004/108/EC.
This appliance meets the eco design requirements of European regulation N. 66/2014, in conformity to the
European standard EN 60350-2.
Before use
IMPORTANT: The cooking zones will not switch on if pots are not the right size.
Only use pots bearing the symbol “INDUCTION SYSTEM” (Figure opposite).
Place the pot on the required cooking zone before switching the hob on.
Existing pots and pans
Use a magnet to check if the pot is suitable for the induction hob: pots and pans are unsuitable if not
magnetically detectable.
- Make sure pots have a smooth bottom, otherwise they could scratch the hob. Check dishes.
- Never place hot pots or pans on the surface of the hob’s control panel. This could result in damage.
OK
NO
Recommended pot bottom widths
L
Ø 21 cm
Max
Flexible Zone
S
Ø 15 cm min ‘ 21 cm max
Min
Ø
12 cm
23 cm
40 cm
9
Ø 14,5 cm
Ø 10 cm min ‘ 14,5 cm max
Installation
After unpacking the product, check for any damage during transport.
In case of problems, contact the dealer or the After-Sales Service.
For built-in dimensions and installation instruction, see the pictures in page 5.
min 5 mm
PREPARING THE CABINET FOR FITTING
WARNING
- Install a separator panel under the hob.
- The lower part of the product must not be accessible after installation.
- Do not fit the separator panel if an undertop oven is installed.
• In order to ensure the correct operation of the product, do not obstruct
the minimum required clearance between the hob and the top of the unit
(min. 5 mm).
• If an undertop oven is installed, make sure the oven is equipped with a
cooling system.
• Do not install the hob above a dishwasher or washing-machine, so that
the electronic circuits do not come into contact with steam or moisture
which could damage them.
min 5 mm
• The distance between the underside of the appliance and the separator
panel must respect the dimensions given in the figure.
min 20 mm
min 5 mm
• In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit
4801 211 00112.
• To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of
the appliance.
Electrical connection
WARNING
- Disconnect the appliance from the power supply.
- Installation must be carried out by qualified personnel who know the current safety and
installation regulations.
- The manufacturer declines all liability for injury to persons or animals and for damage to
property resulting from failure to observe the regulations provided in this chapter.
- The power cable must be long enough to allow the hob to be removed from the worktop.
- Make sure the voltage specified on the dataplate located on the bottom of the appliance is the
same as that of the home.
10
Electrical connection
Connection to the terminal block
For the electrical connection, use an H05RR-F or H05V2V2-F cable as specified in the table below.
Wires
Number x size
220-240 V ~ +
3 x 4 mm
220-240 V 3 ~ +
4 x 1,5 mm2
380-415 V 3N ~ +
5 x 1,5 mm2
380-415 V 2N ~ +
4 x 1,5 mm2
A
380-415 V 3N ~
220-240 V ~
380-415 V 2N ~
220-240 V 3 ~
(Belgium only)
220-240 V ~ (UK and AU)
2
B
C
380-415 V 2N ~
(NL only)
Important:
- Based on the wiring diagram (see figure) either keep or remove the metal jumpers between the screws
on the terminal block L1-L2 and N1-N2.
- If the cable is provided, see the connection instructions attached to the cable.
- Make sure all six screws on the terminal block are tightened after connecting the cables.
Example of jumper present (left) or removed (right). See the wiring diagram for details (the jumpers can be
between L1-L2 and between N1-N2).
Connect the yellow/green earth wire to the terminal with the symbol
This wire must be longer than the other wires.
.
1. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block
hinge (B).
2. Insert the power cable in the cable clamp and connect the wires to the terminal block as indicated in the
connection diagram located near it.
3. Secure the power cable with the cable clamp.
4. Close the cover (C) and screw it on the terminal block with the previously removed screw.
Each time the power is connected, the hob performs an automatic check for a few seconds.
If the hob already has a power cable, follow the instructions attached to the cable. Connect the appliance to
the power supply by means of a multipole switch with minimum contact gap of 3mm.
11
Instructions for use
Control Panel Description
On/Off
Bridge Zone
function
Timer
Power management/Lock
function button
Cooking zone controls and corresponding display
Switching the hob ON/OFF
To switch the hob on, press the
button for approx. 2 seconds until the cooking zone displays light up.
To switch off, press the same button until the displays switch off. All the cooking zones are deactivated
If the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled
down.
If within 10 seconds of switching on, no function is selected, the hob switches off automatically.
Switching on and adjusting cooking zones
0.
Power indicator display
Selected cooking zone indication
Cooking zone positioning
After switching the hob on, activate the required cooking zone by pressing the “+” circular button and
place the pot on the zone.
To increase the power level, push the '+' button. To decrease the poer level push the “-” button.
Deactivation of cooking zones
To switch off the cooking zone, press the corresponding “+” and “-” button for more than 3 seconds.
The cooking zone switches off and, if still hot, the letter “H” appears on the zone display.
12
Instructions for use
Control panel lock
This function locks the controls to prevent accidental activation of the hob. To activate the control panel
lock, switch the hob on and press the Timer button for three seconds; an acoustic signal and a luminous
indicator near the padlock symbol signal activation. The control panel is locked except for the switching
off function. To deactivate the control lock, repeat the activation procedure. The luminous dot goes off and
the hob is active again.
The presence of water, liquid spilled from pots or any objects resting on the button below the symbol can
accidentally activate or deactivate the control panel lock.
Timer
The timer can be used to set the cooking time for a maximum of 99 minutes (1 hour and 39
minutes) for all the cooking zones.
Select the cooking zone to be used with the timer, press the timer and a beep signals the function
(see figure). The display shows “00” and the LED indication comes on. The Timer value can be decreased
and increased by keeping the slider function “+” and “-” buttons pressed. When the set time has elapsed, an
acoustic signal sounds and the cooking zone switches off automatically. To deactivate the timer, keep the
Timer button pressed for at least 3 seconds.
To set the timer for another zone, repeat the above steps. The timer display always shows the timer for the
selected zone or the shortest timer.
To modify or deactivate the timer, press the cooking zone selection button for the timer in question.
CONTROL PANEL WARNINGS.
Residual heat indicator.
The hob is fitted with a residual heat indicator for each cooking zone. These indicators alert the
user when cooking zones are still hot.
If the display shows “H”, the cooking zone is still hot. If the residual heat indicator of a given
cooking zone is lit, that zone can be used, for example, to keep a dish warm or to melt butter.
When the cooking zone cools down, the display goes off.
Incorrect or missing pot indicator.
If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions
for your induction hob, the message “no pot” will appear in the display (see figure at side). If no
pot is detected within 60 seconds, the hob switches off.
Fast boil function (Booster where it is available)
This function, only present on some cooking zones, makes it possible to exploit the hob’s maximum power
(for example to bring water to the boil very quickly).
To activate the function, press the “+” button until “P” appears on the display. After 5 minutes’ use of the
booster function, the appliance automatically sets the zone to level 9.
Power management (Function where it is available)
Thanks to the “Power management” function, the user can set the maximum power the hob can reach, as
required.
This setting is possible at any time and is maintained until the next change.
By setting the required maximum power, the hob automatically adjusts distribution in the various cooking
zones, ensuring that this limit is never exceeded; with the advantage of also being able to manage all the
zones simultaneously, but without overload problems.
4 maximum power levels are available and showed on display: 2.5 – 4.0 – 6.0 – 7.2 kW (7.2 kW is
considered as max power of cooktop)
At the time of purchase, the hob is set to maximum power
After plugging the appliance into the electrical socket, in the first 60 seconds it is possible to set the
required power level by running the following points:
13
Instructions for use
Step
Control panel
Display
1
+
2
Press the Power Management button to confirm
the previous step
The display shows
3
-/+
Press to set the chosen level amongst
the different options available
The light comes on together with the in-use
lights for the individual cooking zones
4
Press the Power Management button to confirm
the previous step
The display shows the set level which
flashes for approximately 2 seconds; after
which the hob emits an acoustic signal
and then turns itself off; it is now ready
for use.
Press for approximately 3 seconds
In case of an error when setting the power, the symbol
appears in the middle and an acoustic signal
sounds for about 5 seconds. In this case repeat the configuration procedure from the beginning. If the error
occurs again, contact the After-Sales Service.
During normal use, if the user tries to increase the maximum available power level when reached, the level
of the zone in use flashes twice and an acoustic signal sounds.
To obtain a higher power in that zone, it is necessary to manually decrease the power level of one or more
already active cooking zones.
Flexible zone
This function can be used to combine two zones and manage them as one single cooking zone. It is perfect
for oval, rectangular and elongated pans (with maximum base dimensions of 40x23 cm). After swiching on
the hob, press the key
: level “0” is shown on the displays of the two cooking zones; both luminous
dots next to the level number are lit, indicating selection of a single zone. To change the power level, move
your finger along the slide touchscreen: the number inside the circle increases/decreases as your finger
slides up/down the tuchscreen, ranging from a min. setting of 1 to a max. of 9. To deactivate the flexible
zone function, press the key: the zones revert to functioning singly. To swetch the cooking zone off, press
OFF.
The booster power level and SENSOR function cannot be used on the same zone when the flexible zone
function is in use. If the timer is set, it will be displayed alongside the hotplate display at the top.
14
Cleaning
WARNING
- Do not use steam cleaners.
- Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator
(“H”) is not displayed.
IMPORTANT: Do not use abrasive sponges or scouring pads. Their use could eventually ruin the glass.
•
•
•
•
After each use, clean the hob (when it is cool) to remove any deposits and stains due to food residuals.
Sugar or foods with a high sugar content damage the hob and must be immediately removed.
Salt, sugar and sand could scratch the glass surface.
Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer’s
instructions).
Troubleshooting guide
•
•
•
•
Read and follow the instructions given in the section “Instructions for use”.
Check that the electricity supply has not been shut off.
Dry the hob thoroughly after cleaning it.
If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table
for instructions.
• If the hob cannot be switched off after using it, disconnect it from the power supply.
ERROR CODE
DESCRIPTION
ERROR
ELIMINATION
POSSIBLE CAUSES
C81, C82
The control panel
switches off because of
excessively high
temperatures
The internal temperature Wait for the hob to cool
of electronic parts is too down before using it
high
again.
F42 or F43
The connection voltage
is wrong
The sensor detects a
discrepancy between the
appliance voltage and
that of the mains supply
F12, F21, F25, F36,
F37, F40, F47, F56,
F58, F60
Call the After-Sales Service and specify the error code
Disconnect the hob from
the mains and check the
electrical
connection
Noises made by the hob
Induction hobs can make whistling or crackling sounds during normal operation, these actually come from
the pots and pans as a result of the characteristics of the bottoms (for example, bottoms made of several
layers of material, or uneven bottoms). These noises vary depending on the pots and pans used and the
amount of food they contain, and are not indicative of a defect of any kind.
In addition, the induction hob is equipped with an internal cooling system to control the temperature of
electronic parts; as a result, during operation and for several minutes after the hob has been switched off,
the noise of the cooling fan will be audible. This is perfectly normal and indeed essential for proper
functioning of the appliance.
15
After-Sales Service
Before contacting the After-Sales Service
1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”.
2. Switch the appliance off and then on again it to see if the problem has been eliminated.
If the problem persists after the above checks, contact the nearest After-Sales Service.
Always specify:
• a brief description of the fault;
• the product type and exact model;
• the Service number (the number after the word Service on the rating plate), located under the appliance
(on the metal plate).
• your full address;
• your telephone number.
If any repairs are required, contact an authorised After-Sales Service Centre (to ensure the use of original
spare parts and correct repairs). Spare parts are available for 10 years.
Power level table
Power level
Type of cooking
Boost Fast heating
Level use
(indicating cooking experience and habits)
Ideal for rapidly increasing the temperature of food to fast boiling in the case
of water or rapidly heating cooking liquids
Max. power
8-9
Frying - boiling
Ideal for browning, starting to cook, frying deep frozen products, fast boiling
7-8
Browning - sautéing boiling - grilling
Ideal for sautéing, maintaining a lively boil, cooking and grilling (for a short
period of time, 5-10 minutes)
6-7
Browning - cooking stewing - sautéing grilling
Ideal for sautéing, maintaining a light boil, cooking and grilling (for a
medium period of time, 10-20 minutes), preheating accessories
4-5
Cooking - stewing sautéing - grilling
Ideal for stewing, maintaining a gentle boil, cooking (for a long period of
time). Creaming pasta
High power
Medium power
3-4
Cooking - simmering thickening - creaming
2-3
1-2
Low power
1
OFF
Melting - defrosting keeping food warm creaming
Zero
Support surface
power
Ideal for long-cooking recipes (rice, sauces, roasts, fish) with liquids (e.g.
water, wines, broth, milk), creaming pasta
Ideal for long-cooking recipes (less than a litre in volume: rice, sauces,
roasts, fish) with liquids (e.g. water, wines, broth, milk)
Ideal for softening butter, gently melting chocolate, thawing small products
and keeping just-cooked food warm (e.g. sauces, soups, minestrone)
Ideal for keeping just-cooked food warm, for creaming risottos and for
keeping serving dishes warm (with induction-suitable accessory)
Hob in stand-by or off mode (possible end-of-cooking residual heat,
indicated by an “H”)
NOTE:
When making quick-cook foods that require perfect heat distribution (e.g. pancakes) on the 28 cm double
cooking zone (where present), use pans no greater than 24 cm in diameter. For delicate cooking (for
example, melting chocolate or butter) use the smaller diameter single zones.
16
Printed in Italy
02/15
400010765294
n
GB
Download PDF

advertising