Whirlpool 045 396 85 Instruction for Use

GB
SUMMARY
BEFORE USING THE DISHWASHER
PAGE
81
PROTECTING THE ENVIRONMENT
PAGE
81
PRECAUTIONS AND GENERAL RECOMMENDATIONS
PAGE
81
ENERGY AND WATER SAVING TIPS
PAGE
81
HOW TO FILL THE SALT CONTAINER
PAGE
82
HOW TO FILL THE RINSE AID DISPENSER
PAGE
83
HOW TO FILL THE DETERGENT DISPENSER
PAGE
83
CONNECTIONS
PAGE
84
MAINTENANCE AND CLEANING
PAGE
86
TROUBLESHOOTING GUIDE
PAGE
87
AFTER-SALES SERVICE
PAGE
87
For maximum satisfaction from your dishwasher, carefully read these user
instructions, consult the wash programme chart and the loading guide.
80
BEFORE USING THE DISHWASHER
•
•
After unpacking, make sure the appliance is
undamaged and that the door closes
correctly. Do not use the appliance if it is
damaged. If in doubt, consult your local
retailer.
Keep potentially hazardous packaging
(plastic bags etc.) out of the reach of children.
•
•
This appliance is designed for use in the
home in compliance with its intended
purpose.
All water and electrical connections must be
carried out by a qualified technician in
compliance with the manufacturer’s
instructions (refer to the enclosed installation
booklet) and current local safety regulations.
PROTECTING THE ENVIRONMENT
1. Packing
The packing box may be fully recycled as
confirmed by the recycling symbol
.
2. Appliance
The appliance is built from reusable
materials.
If you decide to scrap the dishwasher, it
must be disposed of in compliance with local
waste disposal laws. Before scrapping, cut
off the power cable so that the appliance
cannot be connected to the mains.
PRECAUTIONS AND GENERAL RECOMMENDATIONS
Child safety
• Do not allow children to play with the
dishwasher.
• Store the detergent, rinse aid and salt in a dry
place out of the reach of children.
General recommendations
• Only use detergents, rinse aids and
regeneration salts (not applicable for
Australia) specially recommended for use in
domestic dishwashers.
• On completion of the wash programme
switch off the dishwasher and turn off the
water tap.
• Before cleaning or carrying out maintenance,
switch off the appliance, disconnect the
mains plug and turn off the water tap.
• If a fault occurs, switch off the appliance and
turn off the water tap.
• The open dishwasher door can only support
the weight of the loaded rack when pulled
out. Do not rest objects on the open door or
sit or stand on it since the appliance may
topple over.
•
•
•
•
If necessary, the power cable may be
replaced with one the same obtained from
our After-Sales Service. The power cable
must only be replaced by a qualified
technician.
For appliances with water-stop system:
The water inlet hose and plastic casing
contain electrical components. Do not
therefore cut the hose or immerse the plastic
casing in water. If the hose is damaged
switch off the appliance immediately.
Do not use solvents inside the dishwasher:
risk of explosion!
Load capacity: -12 place settings
EC Declaration of Conformity
This appliance has been designed,
constructed and distributed in compliance
with the safety requirements of
EC Directives:
• 73/23/EC
• 89/336/EC
• 93/68/EC.
ENERGY AND WATER SAVING TIPS
•
•
Do not rinse crockery under running water.
Always fully load the dishwasher before
switching on.
•
If ecological energy sources are available
such as solar panel heating, heat pumps or
centralised heating systems, the appliance
may be connected to the hot water mains up
to a maximum temperature of 60°C.
Make sure the water inlet hose is of the
correct type. Refer to the “Connections”
chapter in these user instructions.
81
HOW TO FILL THE SALT CONTAINER
(Not applicable for Australia).
Check the water hardness level in your
area. Consult your local Water Board or
check your last water bill.
•
•
•
If the water hardness level exceeds
category 1, before using the dishwasher
for the first time, fill the salt container and
run a wash cycle so that any excess
saline solution discharged is immediately
removed by the water to prevent
corrosion. The pre-rinse cycle is not
sufficient for this purpose.
Check the salt level regularly.
Important: Only use regeneration salts
recommended for use in domestic
dishwashers.
Do not fill the salt container with
detergent as this will cause irreparable
damage to the water softener system.
To fill the salt container:
1. Remove the lower rack.
2. Unscrew the cap by turning it counter-clockwise.
3. If the dishwasher is new, fill the salt container
to the rim with water.
4. Fill the container to the rim with salt
(max. 2 kg) and stir with a spoon handle.
5. Screw the cap back on by turning it
clockwise.
Salt level indicator
The green float is clearly visible in the cap
window when the salt container is full. The green
float lowers and is no longer visible when the salt
container is empty.
82
HOW TO FILL THE RINSE AID DISPENSER
The rinse aid facilitates drying and prevents the
formation of unsightly spots and streaks on
crockery. Before using the dishwasher for the
first time, fill the rinse aid dispenser.
Thereafter, regularly check the rinse aid level.
Only use rinse aids recommended for use in
domestic dishwashers.
1. Open the rinse aid dispenser by turning knob
A counter-clockwise (see diagram) and
pulling it out.
2. Fill with rinse-aid until the visual indicator B
turns dark.
3. Close the rinse aid dispenser.
4. Immediately wipe away any spilt rinse aid
(from metal parts as well) to prevent
excess suds which may spoil washing
results.
Rinse aid level indicator
light = empty
dark = full.
How to adjust the rinse aid dosage
regulator.
(Open the cover and close again following
adjustment).
Factory setting: 3.
If you are not satisfied with washing or drying
results, change the dial setting with a spoon
handle or coin.
If crockery is prone to whitish streaks, reduce the
dosage by turning the dial to a lower setting. If
instead crockery is wet, increase the dosage by
turning the dial to a higher setting.
HOW TO FILL THE DETERGENT DISPENSER
Only use detergents recommended for use in
domestic dishwashers.
If you use detergents in pellet form, follow the
manufacturer’s directions for use.
Always use the recommended dosage stated on
the detergent pack. The use of detergent in
excess of the recommended dosage may cause
pollution. The recommended dosage varies
between different brands.
Only fill the detergent dispenser prior to
starting a wash programme.
For programmes with pre-rinse:
1. Open the detergent dispenser lid.
2. Pour two thirds of the recommended dosage
into the inner compartment A.
3. Pour the remaining third into the small
compartment B.
Note: Remember to close the lid.
For programmes without pre-rinse:
• Pour the entire recommended dosage into
the wider compartment. Adjust detergent
quantity between Min and Max according to
the wash load.
Note: Remember to close the detergent
dispenser lid.
83
CONNECTIONS
Refer to the separate installation instructions
booklet.
Water inlet and drain:
• Strictly follow local Water Board regulations.
• Make sure the inlet and drain hoses are kinkfree and are not crushed.
• If the hose length does not suffice, replace
with similar hoses obtained from your local
dealer or our After-Sales Service.
• The inlet hose must be securely clamped to
the water tap to prevent leaks.
• The inlet water temperature varies according
to the model installed: inlet hose marked
“25° C”.
All other models: maximum temperature 60° C.
• When installing the appliance, make sure the
drain water discharges correctly and, if
necessary, remove the wire gauze from the
sink siphon.
• Secure the drain hose with a clamp to the
siphon to prevent it from dropping off during
operation.
• For appliances with water-stop system only:
if the water connections are made correctly,
the water-stop system safeguards your home
against damage caused by flooding.
84
Electrical connections:
• Closely adhere to local Electricity Board
regulations.
• Voltage information is shown on the rating
plate mounted inside the door on the right
hand side.
• The appliance must be earthed as prescribed
by law.
• Do not use extension leads or multiple
adapters etc.
• Before carrying out maintenance, disconnect
the mains plug.
• Do not use the dishwasher if it has been
damaged in transit. Consult your local retailer
or our After-Sales Service.
• The power cable must only be replaced by a
qualified technician.
CONNECTIONS
1) ELECTRICAL CONNECTIONS
“Warning - this appliance must be
earthed”
This appliance is normally supplied with a
mains lead having a plug fitted in the factory
which has been checked for correct earth
continuity.
If the fitted plug is not suitable for your socket
outlet, or if the machine’s mains lead is not
fitted with a plug, you should fit a suitable new,
good quality plug by following the instructions in
(2) below.
Any unsuitable plug should be cut off and
disposed of in order to avoid a possible shock
hazard should it be inserted into a socket.
2.2 Non-polarized plugs (e.g. 2 pin with side
earth contact)
The wire which is coloured GREEN AND
YELLOW must be connected to the earth
contact. The other two wires should be
connected to the two pins, irrespective of
colour.
3) FUSE REPLACEMENT
If the mains lead of this appliance is fitted with
a BS 1363A 13 amp fused plug, replace the
fuse only with an A.S.T.A. approved type
conforming to BS 1362 and proceed as follows:
2) CONNECTION TO A REWIRABLE
PLUG - to be carried out only by a
qualified electrician
The wires in the mains lead are coloured in
accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN AND YELLOW - “EARTH” (“E”)
To fit a new plug, proceed as follows:
2.1 Polarized Plugs (e.g. 3 pin, 13 amp plug
conforming to BS 1363A)
a. The GREEN AND YELLOW wire must be
connected to the terminal in the plug which
is marked with the letter “E” or by the Earth
symbol
or coloured yellow or green and
yellow.
b. The BLUE wire must be connected to the
terminal which is marked with the letter “N”
or coloured black.
c. The BROWN wire must be connected to the
terminal which is marked with the letter “L”
or coloured red.
1. Remove the fuse cover (A) and the fuse (B).
2. Fit the replacement 13 A fuse into the fuse
cover.
3. Refit both into the plug.
For all other types of plug, the supply socket
should be protected by a 16 A fuse or circuit
breaker at the distribution board
85
MAINTENANCE AND CLEANING
Before cleaning or carrying out maintenance,
switch off the appliance, disconnect the
mains plug.
1. Clean the appliance exterior with a neutral
detergent. Do not use abrasive detergents.
2. Regularly wipe the door seal and inside of the
door with a damp cloth to remove any food
residues.
If the spray nozzles become clogged with
food residues
(clean the spray arms as follows).
1. Unscrew the securing wing-nuts.
2. Remove the spray arms.
3. Clean them under running water.
4. Remount the spray arms and tighten the nuts.
Note: Do not interchange the upper and
lower spray arms. The spray jets must point
upwards.
Cleaning the soil filter:
If necessary, the filter can be cleaned after
each wash programme as follows:
1. Remove the lower rack.
2. Release and pull out the filter.
Separate the fine filter from the coarse filter.
3. Clean all the components.
4. Reassemble and reposition.
86
TROUBLESHOOTING GUIDE
If a fault occurs, before contacting our After-Sales Service, make the following
checks to try and remedy the problem.
Restart the wash programme to see if the
fault repeats:
• Press the On/Off button or push and pull the
program knob to restart the programme.
If the malfunction persists, switch off the
appliance and turn off the water tap. Call our
After-Sales Service.
The appliance will not switch on:
• Power plug properly inserted in the mains
socket?
• Power failure?
• Have you switched the dishwasher on?
• Have you pressed the Start button?
• Tap turned on? If not:
• Turn on the water tap.
• Make sure the water hose filter is not
clogged.
To do this, turn off the water tap, disconnect
the water hose, clean the filter, reconnect
the water hose to the tap and turn on the tap.
• Filters clogged?
Crockery loaded upside down?
When loading large items in particular, make
sure the water circulates and does not collect
inside them.
• Door closed properly?
Crockery still dirty after washing:
• Have you selected the correct programme?
• Have you used the correct amount of
detergent?
• Filters clogged or incorrectly assembled?
• Spray arms blocked or nozzles clogged?
• Salt container cap screwed down?
(Not applicable for Australia).
• Crockery loaded correctly? (the water jets
must spray the entire surface of all items).
Spotted crockery:
• Salt container empty?
(Not applicable for Australia).
• Insufficient detergent?
Spotted glasses and cutlery:
• Too much rinse aid? (Adjust the rinse aid
regulator to a lower setting).
Crockery not dry, calcium stains:
• Insufficient amount of rinse-aid? (adjust the
rinse-aid on a higher setting).
AFTER-SALES SERVICE
Before contacting our After-Sales Service:
•
The service number
(the number after the
word Service on the
adhesive label)
located inside the
door on the right
hand side.
•
Your name, address and telephone number.
1. Try to remedy the problem
(See “Troubleshooting Guide”).
2. Switch off the dishwasher and restart the
wash programme to see if the fault repeats.
If, after carrying out the above checks the
malfunction persists, call our After-Sales
Service and specify:
•
•
The nature of the problem.
The appliance type and model.
87

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project