SAFETY INSTRUCTIONS
EN
IMPORTANT TO BE READ AND
OBSERVED
Download the complete instruction WARNING: Unattended cooking on a
manual on http://d
ocs.whirlpool.eu or hob with fat or oil can be dangerous - risk
call the phone number shown on the of fire. NEVER try to extinguish a fire with
warranty booklet.
water: instead, switch off the appliance
and then cover flame e.g. with a lid or a
Before using the appliance, read these
fire blanket.
safety instructions. Keep them nearby for
Do not use the hob as a work surface or
future reference.
support. Keep clothes or other flammable
These instructions and the appliance
materials away from the appliance, unitl
itself provide important safety warnings,
all the components have cooled down
to be observed at all times. The
completely - risk of fire.
manufacturer declines any liability for
failure to observe these safety instructions, PERMITTED USE
for inappropriate use of the appliance or CAUTION: the appliance is not intended
to be operated by means of an external
incorrect setting of controls.
Very young children (0-3 years) should switching device, such as a timer, or
be kept away from the appliance. Young separate remote controlled system.
children (3-8 years) should be kept away This appliance is intended to be used in
from the appliance unless continuously household and similar applications such
supervised. Children from 8 years old and as: staff kitchen areas in shops, offices and
above and persons with reduced physical, other working environments; farm
sensory or mental capabilities or lack of houses; by clients in hotels, motels, bed &
and
other
residential
experience and knowledge can use this breakfast
environments.
appliance only if they are supervised or
have been given instructions on safe use No other use is permitted (e.g. heating
and understand the hazards involved. rooms).
Children must not play with the appliance. This appliance is not for professional
Cleaning and user maintenance must not use. Do not use the appliance outdoors.
be carried out by children without INSTALLATION
The appliance must be handled and
supervision.
installed
by two or more persons - risk of
WARNING: The appliance and its
injury.
Use
protective gloves to unpack
accessible parts become hot during use.
and
install
risk of cuts.
Care should be taken to avoid touching
Installation,
including water supply (if
heating elements.
any),
electrical
connections and repairs
Children less than 8 years of age shall be
must
be
carried
out by a qualified
kept away unless continuously supervised.
technician.
Do
not
repair
or replace any
WARNING: If the hob surface is cracked,
part
of
the
appliance
unless
specifically
do not use the appliance - risk of electric
stated
in
the
user
manual.
Keep
children
shock.
away
from
the
installation
site.
After
WARNING: Danger of fire: Do not store
unpacking
the
appliance,
make
sure
that
items on the cooking surfaces.
it
has
not
been
damaged
during
transport.
CAUTION: The cooking process has to
be supervised. A short cooking process In the event of problems, contact the
dealer or your nearest After-sales Service.
has to be supervised continuously.
Once installed, packaging waste (plastic,
styrofoam parts etc.) must be stored out
of reach of children - risk of suffocation.
The appliance must be disconnected
from the power supply before any
installation operation - risk of electric
shock. During installation, make sure the
appliance does not damage the power
cable - risk of fire or electric shock. Only
activate the appliance when the
installation has been completed.
Carry out all cabinet cutting operations
before fitting the appliance and remove
all wood chips and sawdust.
If the appliance is not installed above
an oven, a separator panel (not included)
must be installed in the compartment
under the appliance.
ELECTRICAL WARNINGS
Do not use abrasive or corrosive
products, chlorine-based cleaners or pan
scourers.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is
marked with the recycle symbol .
The various parts of the packaging must therefore be
disposed of responsibly and in full compliance with
local authority regulations governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable
or reusable materials. Dispose of it in accordance
with local waste disposal regulations. For further
information on the treatment, recovery and recycling
of household electrical appliances, contact your local
authority, the collection service for household waste
or the store where you purchased the appliance. This
appliance is marked in compliance with European
Directive 2012/19/EU, Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent negative consequences for the
environment and human health.
It must be possible to disconnect the The symbol on the product or on the accompanying
indicates that it should not be treated
appliance from the power supply by documentation
as domestic waste but must be taken to an appropriate
unplugging it if plug is accessible, or by a collection center for the recycling of electrical and
multi-pole switch installed upstream of electronic equipment.
the socket in accordance with the wiring ENERGY SAVING TIPS
Make the most of your hot plate’s residual heat by
rules and the appliance must be earthed switching it off a few minutes before you finish cooking.
in conformity with national electrical The base of your pot or pan should cover the hot plate
completely; a container that is smaller than the hot
safety standards.
plate will cause energy to be wasted.
Do not use extension leads, multiple Cover your pots and pans with tight-fitting lids while
sockets or adapters. The electrical cooking and use as little water as possible. Cooking with
lid off will greatly increase energy consumption.
components must not be accessible to the
Use only flat-bottomed pots and pans.
the user after installation. Do not use the DECLARATION OF CONFORMITY
appliance when you are wet or barefoot. This appliance meets the Ecodesign requirements of
Do not operate this appliance if it has a European Regulation n. 66/2014, in compliance with
damaged power cable or plug, if it is not the European standard EN 60350‑2.
working properly, or if it has been
damaged or dropped.
If the supply cord is damaged, it must
be replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a
hazard - risk of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched off and disconnected from the
power supply before performing any
maintenance operation; never use steam
cleaning equipment - risk of electric
shock.
EN
INSTALLATION
• The cooktop must be set into a worktop between 20 mm and 50 mm deep.
• There must be nothing between the cooktop and the oven (cross rails, brackets, etc.).
• If the cooktop is to be installed next to a column unit, leave a distance of at least 100 mm from the edge
of the cooktop to the side of the column unit.
• For built-in dimensions and installation see the picture in this paragraph.
• Apply the supplied gasket to the cooktop (unless it has already been fitted), after having cleaned its surface.
• We recommend you seal the internal edges of the worktop with wood glue or silicone.
• Do not install the cooktop near a dishwasher or washing machine, so that the electronic circuits do not
come into contact with steam or moisture, which could damage them.
• ATTENTION: to install the hob on other surfaces than wood (marble, plastic, ceramic, marble, stone,
etc.) remember to ask After Sales Service for the fixing plates (fig. 2) .
PLACING THE HOB
Important: remove any protective film before installing the hob.
Make sure that the opening in the worktop for the hob is cut according to the dimensions given in the drawing,
paying attention to the tolerance range. The hob should not be forced into the worktop. Forcing the glassceramic top may cause it to crack (even at a later date)!
• If the worktop is made of wood, use the appropriate brackets, spring clips and screws provided.
• Position the 4 clips (A), if not alreay fitted, around the cooktop frame, in the slots provided, see Fig. 1.
• Measure the centre of the vertical sides of the cut out a shown in Fig. 2.
• Position the centre of the brackets (C) on the centre of the side previously identified.
• The upper edge of the brackets must be flush with the worktop surface.
• Secure using the 4 screws (B)provided that should screwed into the pre-prepared holes.
• Insert the cook hob into the pre-prepared hole ensuring that the clips (A) lodge into the bracket slots provided
(C Fig. 4 e 5).
• If the worktop is made of marble, plastic, ceramic, stone, etc., the hob must be secured with special
brackets (C) (fig. 2). Fit the hob into the worktop (fig. 1). Place the 4 brackets (C) in position shown in fig. 6.
Fasten the 4 screws (E) in the positions (D) (fig. 6).
C
3
C
A
4
C
E
D
B
A
5
1
2
6
DIMENSIONS AND DISTANCES TO BE MAINTAINED
40 mm
580 X 510 mm
580 mm
0
560 +2 mm
510 mm
Min. 50 mm
0
490 +2
482 mm
552 mm
R = Min. 6,5 mm
Max. 16 mm
mm
min 20 mm
ELECTRICAL CONNECTION
Electrical connection must be made before connecting the appliance to the electricity supply.
Installation must be carried out by qualified personnel who know the current safety and installation regulations.
Specifically, installation must be carried out in compliance with the regulations of the local electricity supply
company. Regulations require that the appliance be earthed. Connection to the mains must be carried out by a
qualified technician in accordance with the manufacturer's instructions and in compliance with local regulations.
The installer is responsible for connecting appliances correctly to the mains and for observing the safety
regulations. After the oven has been installed, the electrical components must be inaccessible. Important: do
not connect the oven to the power supply before you have finished connecting the oven and cooktop. Before
connecting the oven (or box) to the power supply, make sure that the hob is among the ones listed in the hob/
oven pairing product sheet provided.
CONNECTION TO THE TERMINAL BLOCK
Make sure that the voltage indicated on the rating plate is the same as the mains voltage. Technical data
is given on the rating plate on the edge of the hob and also below:
POWER SUPPLY
VOLTAGE
NUMBER OF WIRES
X DIMENSION
230V ~ +
H05 RR-F 3 x 2,5 mm2
230V 3~ +
H05 RR-F 4 x 1,5 mm2
H
F
G
7
8
NOTE: the yellow/green earth wire must be connected to the terminal with the symbol
and must be longer
than the other wires.
• Connect the connectors of the hob (G) to the connectors of the oven (F) matching the colours and alignment
of the housing guides visible on the top of the connectors (fig. 7).
• Then make the connection by pushing the connectors all the way in, making sure that the tongue clicks into
place.
• Unscrew the nut of the ground screw (H) (fig. 8) on the top covering of the oven and insert the yellow/green
ground cable, leaving the washer in place. Screw the nut back onto the screw and tighten it as far as it will go.
Important: if the connection and colour coding of the hob terminals do not comply with the data given on the
hob/oven pairing product sheet located on the top of the oven, please request the adapter kit code AMC 873,
available from After Sales Service.
EN
PRODUCT DESCRIPTION
1.Radiant cooking zone Ø 145
2.Radiant cooking zone Ø 210
3
2
3.Radiant cooking zone Ø 145
4.Radiant cooking zone Ø 180
4
1
FIRST TIME USE
Before use, remove:
• adhesives stuck on the hob;
• cardboard guards and protective plastic film;
• check whether the hob has been damaged during
transport. If in doubt, contact the After Sales Service.
DAILY USE
SWITCHING THE HOB ON/OFF
To use the hob, turn the knob(s) clockwise and set it/
them to the required power.
To turn the hob off, turn the knob(s) back to position
“0”.
The hob is fitted with residual heat indicators. These
light up when the cooking zones reach temperatures
that could cause burns. These indicators remains alight
after the cooking zones are switched off, and turn off
only when the zones are no longer hot enough to be
dangerous.
IMPORTANT: To avoid a permanent damage the hob:
• do not use pots with bottoms that are not flat;
• do not use metal pots with enamelled bottom;
• do not place hot pots/pans over the control panel.
ACCESSORY
Child guard AMH 122. This
accessory can be obtained
from the After Sales Service
under code number 4819 310
18436 or from your dealer
under
reference
number
017124.
MAINTENANCE AND CLEANING
Disconnect the appliance from the power • Sugar or foods with a high sugar content can damage
the hob and must be immediately removed.
supply.
• Salt, sugar and sand could scratch the glass surface.
• Use a soft cloth, absorbent kitchen paper or a specific
• Do not use steam cleaning equipment.
hob cleaner (follow the Manufacturer’s instructions).
• Do not use abrasive sponges or scouring pads as
• Spills of liquid in the cooking zones can cause the
they may damage the glass.
pots to move or vibrate.
• After each use, clean the hob (when it is cool) to
• After cleaning the hob, dry thoroughly.
remove any deposits and stains from food residue.
TROUBLESHOOTING
If the hob will not operate correctly, before calling the • Turn the hob off and on again, to make sure that the
After-Sales Service, refer to the Troubleshooting Guide
problem has been solved.
to determine the problem.
• Make sure that the knob is not turned to “0”. Turn the
multi-pole switch to “Off” for a few minutes and then
• Read and follow the instructions given in the section
turn it back to “On”.
“Daily use”.
• Check that the electricity supply has not been shut If after the above checks the fault still occurs, get in
off.
touch with the nearest After Sales Service.
AFTER-SALES SERVICE
In order to receive a more complete assistance, please
register your product on www.whirlpool.com/
register.
BEFORE CALLING THE AFTER-SALES SERVICE:
1.See if you can solve the problem by yourself
with the help of the suggestions given in the
TROUBLESHOOTING.
2.Switch the appliance off and back on again to see if • the service number (number after the word Service
on the rating plate). The service number is also
the fault persists.
indicated on the guarantee booklet;
Type: XXX
Mod.: XXX
XXXXXXXXXXXXXXXXXXXX
Made in X
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXX
01
XXXX XXX XXXXX
XX XXXX XXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
IF AFTER THE ABOVE CHECKS THE FAULT STILL
OCCURS, GET IN TOUCH WITH THE NEAREST AFTERSALES SERVICE.
To receive assistance, call the number shown on the • your full address;
warranty booklet or follow the instructions on the • your telephone number.
website www.whirlpool.com.
If any repairs are required, please contact an authorized
When contacting our Client After sales service, always after-sales service (to guarantee that original spare
specify:
parts will be used and repairs carried out correctly).
• a brief description of the fault;
• the type and exact model of the appliance;
400011314284
">
