Hotpoint BCI480.C Instruction for Use

Instructions for Installation and Use
Dishwasher
Model BCI 480
D 1509)50-4
2
D 1509)50-4
Contents
Electrical Connection
For Your Safety
Installation
Getting to know your Dishwasher
The Controls
How to use your Dishwasher
Programme Chart
Before Using your Dishwasher
Loading your Dishwasher
Care and Cleaning
Troubleshooting
Information for Test Labs
After Sales Service
Hotpoint Guarantee
Notes
Key Contacts
4
5
6
7
7
8
9
10-11
12
13
14
15
16
17
18-19
Back Cover
Retention of this Instruction Book
This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of
the appliance.
If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book is also
provided so the new owner can become familiar with the appliance and safety warnings.
If the Book is lost or damaged a copy may be obtained from:
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.
3
D 1509)50-4
Electrical Connection
WARNING: This appliance must be earthed.
Fuses
Your appliance comes fitted with a plug and a 13A fuse. If
you need to replace the fuse, only those rated at 13A and
ASTA approved to BS1362 should be used. If you lose
the fuse cover, a replacement may be obtained from your
local authorised Service Centre or Electrical company.
Correct replacement is identified by colour coding or the
marking on base of plug.
it is open, this could damage the door or cause the
appliance to tip forward.
Once the appliance has been installed, the power
supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be
replaced by the manufacturer or its Technical Assistance
Service in order to prevent all potential hazards. (See
Assistance)
WARNING: DO NOT use the plug unless the fuse
cover is fitted.
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Changing the Plug
Safety Information
Cut off and dispose of the supplied plug if it does not
fit your socket.
To avoid a shock hazard DO NOT insert the
discarded plug into a socket anywhere else.
Wires in the mains lead are coloured accordance with the
following code:
Green/Yellow Earth
Blue
Neutral
Brown
Live
If you change the plug, the colour of the wires in the
mains lead may not correspond with the terminal
markings in the plug, which if not coloured, could be:
EARTH
NEUTRAL
LIVE
‘E’ or
‘N’
‘L’
At the time of delivery...
All functions of your dishwasher have been thoroughly
tested at the factory. A small number of water marks
may have been left as a result, they will disappear when
the appliance is used for the first time.
- This appliance should only be connected to a 230/240V
AC source, via a properly installed earthed socket.
- Use the dishwasher solely in a domestic environment.
- DO NOT stand or place heavy objects on the door when
it is open, this could damage the door or cause the
appliance to tip forward.
If your family includes children...
- DO NOT allow children to play with the appliance or
tamper with its controls.
- Keep detergents and rinse aids away from children.
Keep children away from the open door of a
dishwasher, there could still be some detergent left
inside.
Changing the Mains Lead
A lead can be ordered from Hotpoint Service
UK: 08709 066 066 or
Republic of Ireland: 1850 302 220
- If you have damaged the existing lead or require a
longer one a charge will be made. It is strongly advised
that this work is carried out by a qualified electrician.
- If the domestic wiring includes a residual currentoperated circuit breaker, ensure that it conforms to the
latest regulations.
The dishwasher must not be connected to the electricity
supply while installation is being carried out.
- This appliance should only be connected to a 230/240V
AC source, via a properly installed earthed socket.
- Use the dishwasher solely in a domestic environment.
- DO NOT stand or place heavy objects on the door when
4
CAUTION:
The dishwasher meets the requirements set out by the
regulations in force concerning safety and electrical
equipment.
Any technical checks should be conducted exclusively by
a trained and authorised technician: Repairs carried out
by unaithorised persons will invalidate the guarantee, as
well as posing a potential hazard to the user.
The manufacturer declines all responsibility for
damage to persons or property resulting from failure to
observe the above precautions, from tampering with even
a single component or from the use of non-original spare
parts.
D 1509)50-4
For your Safety
This manual forms an integral part of the appliance. It must always be kept handy for reference. Read through all the
instructions contained in this manual before using the dishwasher.
Installation must be performed by a qualified technician, in compliance with the regulations in force, including the
prevention and elimination of radio frequency interference.
The dishwasher is designed for washing and drying dishes, any other use shall be considered improper. The
manufacturer declines all responsibility for uses other than those described above.
1. Seperate the various
packaging materials and
dispose of safely - DO
NOT leave discarded
packaging material
around the home.
2. After removing the
packaging, check to
make
sure
your
appliance is intact. If in
doubt,
contact
a
qualified professional.
3. DO NOT use extension
leads and multiple plugs.
If the electricity supply
wire is not long enough,
then have it replaced
with one of the correct
length and remember
that it should be free of
bends or dangerous
kinks.
4. If the supply cord is
damaged, it must be
replaced
by
the
manufacturer, its service
agent in order to avoid a
hazard.
5. The mains plug must be
easily accessible after
installation.
6. If the appliance is not
operating properly or if
maintenance operations
are
necessary,
disconnect
the
dishwasher from the
mains power supply
(unplug it!).
7. DO
NOT
install
outdoors, not even if the
area is covered by a
roof: it is extremely
dangerous to leave it
exposed to rain and
thunderstorms.
8. If installed on a carpeted
or covered floor, ensure
that the openings on the
underside are not
obstructed.
9. Do not touch the heating
element during or
straight after a wash
cycle.
10. If the appliance
malfunctions, turn off
the water inlet tap and
disconnect the plug
from the wall socket.
Then read the section
entitled
"Troubleshooting". If
you cannot resolve the
problem, then call
Hotpoint Service (see
KEY CONTACTS, back
page).
11. The door should not be
left in the open position
since this could present
a tripping hazard.
The dishwasher is intended for use by adults. DO
NOT allow children to come near or play with the controls.
Keep children away from detergents and clear of the
dishwasher door when open.
Keep all packaging material away from children.
1. DO NOT use solvents, such as alcohol or turpentine
which may cause an explosion.
2. DO NOT load dishes to wash that are soiled with ash,
wax or paints.
3. DO NOT lean, sit or stand on any part of the dishwasher
- this could cause injury and/or damage the appliance.
4. DO NOT drink any water residues from inside the
dishwasher.
The rating plate, featuring
the technical data, serial
number and markings, is
visibly positioned on the
inner edge of the door.
DO NOT remove the rating
plate.
5
D 1509)50-4
Installation
Choose where you want to
install your dishwasher, you
can place it so that its sides
or back panel are side by
side with furniture or up
against the wall. (See the
built-in instructions for the
measures). The dishwasher
is provided with water supply
and drain hoses, which can
be directed towards the left
or right to facilitate
appropriate installation.
Levelling
Once the appliance is
positioned, adjust the feet by
screwing them in or out
depending on how high you
want it and to level it so that
it is horizontal. Make sure
that it is not inclined more
than 2 degrees. If the
appliance is level, it will help
ensure its correct operation.
It is strongly recommended
to use a new hose to
connect the dishwasher to
the water supply line, and the
old hose-set should not be
reused. Asking to specilized
shop or an authorized
service technician (see
Service).
Condensation-proof tape
On some models, a
transparent condensationproof adhesive tape has been
provided.
It should be stuck onto the
lower side of your wooden
worktop to protect it from the
formation of condensation.
When not provided, this tape
can be requested as a spare
part from authorised
retailers.
Anti-flooding protection
To ensure floods do not
Height Adjustment
Insert the appliance into the occur, the dishwasher:
cutout and then adjust the - is provided with a special
height using the screws system which blocks the
located on the front bottom water supply in the event of
part of the machine. Use a anomalies or leaks from
screwdriver to turn the inside the appliance.
screws in the clockwise or - is provided with a Water
anti-clockwise direction to Stop safety device, in other
increase or decrease the words it has a water inlet
height respectively.
hose that consists of a
transparent hose on the
outside and a red hose on
Cold water connection
Connect the cold water the inside: both the hoses
supply hose, and making can withstand extremely high
sure that it is fastened tightly pressure. If the internal hose
in place. If the water hoses breaks, the external hose
are new or have been out of becomes a bright red colour
use for an extended period and carries the water instead,
of time, let the water run to thus avoiding any leakage.
make sure it is clear and free
of impurities before making
the connection. If this
precaution is not taken, the
water inlet could get blocked,
causing damage to your
dishwasher.
6
It is very important to check
the external hose regularly:
if it is a bright red colour, it
must be replaced by an
authorised technician as
soon as possible (see
Assistance).
WARNING:
HAZARDOUS
VOLTAGE!
Under no circumstance
should the water inlet hose
be cut as it contains live
electrical parts.
Drain hose connection
WARNING: Connect your
dishwasher drain hose to
pipes which connect to the
foul drain system and not to
surface water drains.
IMPORTANT: For the
correct operation of your
dishwasher, it is essential to
comply with the following
information:Standpipe:
Ensure that the hose is not
pushed too far down the
standpipe.
If the end of your drain hose
is fitted with ‘retaining flaps’,
ensure they are inserted fully
into the standpipe. This will
prevent the pipe from
jumping
out
during
installation and use.
DO
NOT
position the
standpipe near
an electrical
outlet.
ENSURE that
the drain hose is not kinked
and it is routed as shown in
the diagram.
The standpipe should have
a bore of at least 38mm (11/
2”). It should be installed as
shown, have a trap fitted and
must discharge into the
same drain system as your
household sink.
It MUST NOT be connected
to a surface water drain.
Sink Waste System:
For under sink drainage:
Before connecting the drain
hose, remove any internal
restrictions - This will
prevent a build up of debris
which could cause a
blockage.
Remove any restrictions
from the waste spigot and
ensure that the sealing bung
is removed. The hose should
be routed, such that it is
raised to a minimum height
of 800mm (31/2”).
NOTE: Ensure the sink
outlet pipe has a minimum
diamtere of 32mm.
1. Untie the end of the GREY
drainage hose from the rear
of the appliance.
2. Reposition the ‘Hooked
End Support’ as required
along the GREY drainage
hose.
3. If fitting an under sink
waste disposal unit, cut out
the membrane, bung or
blanking plug.
Ensure the drain hose is
securely attached, to prevent
it coming away while the
machine is in use and
causing a flood.
D 1509)50-4
Getting to know your Dishwasher
G
E
E. Upper basket
I.
Bottom spray arm
F. Top spray arm
J. Salt container cap
G. Basket height adjuster
K. Washing filter
H. Lower basket
L. Detergent and rinse aid
dispenser
F
K
I
The Controls
ON-OFF Button
Press this button to
switch the appliance on.
ON-OFF Indicator light
This light informs you that
the dishwasher is on.
Wash Programme Selector
Each time this button is
pressed,one of the cycle
indicator lights will come
on in sequence.
Wash Cycle indicator
lights
This light informs you
which cycle you have
selected or the one in
progress.
Low salt indicator light
This light warns you that
it is time to add more salt.
Low rinse aid indicator
light
This light warns you that
it is time to add more rinse
aid.
L
Delayed start select
button
This button delays the
start of the wash cycle
you selected by 2, 4 or 6
hours.
Delayed start indicator
light
This indicates that the
delayed start has been
set
Wash
Programme
Select
button
Delayed Start
button
Wash Cycle
indicator lights
Low Salt
indicator light
ON/OFF
indicator light
Low Rinse Aid
indicator light
7HFKQLFDO FKDUDFWHULVWLFV
:LGWK
FP 'HSWK
FP +HLJKW
FP ª
0DLQV ZDWHU SUHVVXUH
ON/OFF
button
Delayed Start
indicator light
Technical Characteristics
&DSDFLW\
H
J
VWDQGDUG SODFH VHWWLQJV
SVL ª 03D ª EDU
3RZHU YROWDJH
6HH GDWD SODWH
7RWDO DEVRUEHU SRZHU
6HH GDWD SODWH
)XVH
6HH GDWD SODWH
This dishwasher conforms
to the following European
Community Directives:
• 73/23/EEC of
19/02/73 (Low
Voltage) and
subsequent
modifications;
• 89/336/EEC of
03/05/89
(Electromagnetic
Compatibility)
and subsequent
modifications;
• 97/17/C E
(Labelling)
• 02/96/CE
(Waste Electrical
and Electronic
Equipment)
7
D 1509)50-4
How to use your Dishwasher
First of all.
- Turn on the water supply
tap completely.
- Add the correct amount of
detergent.
- Load the baskets correctly.
- Check that the spray
arms rotate freely.
- Close the door securely.
-After performing all the operations described in the previous paragraphs, open the
appliance door and press
ON-OFF button: the ON/OFF
indicator light comes on.
Your appliance is now on and
awaiting instructions.
Select the wash
cycle.
Select the wash cycle by
pressing “Wash Programme Selector” button.
Each time this button is
pressed, one of the Cycle
indicator lights will come on
in sequence, select the wash
cycle most suitable for the
type of dishes to wash (see
‘Programme Chart’).
Close the door and after a
few seconds, you will hear a
short beep: the wash cycle
has begun.
AUTO WASH CYCLES: This
model of dishwasher is
equipped with a special sensor which can be used to assess the level of soiling and
automatically select the
most efficient and economic
wash cycle accordingly. The
duration of the auto wash
cycles may vary due to the
operation of the sensor.
8
Modifying a wash cycle in progress.
There's been a
power failure or you
If you have chosen the opened the
wrong cycle - You can dishwasher door
modify the wash cycle in
progress, if it has only just
started. Open the appliance
door carefully to avoid any
hot water splashes, then
keep “Wash Programme
Selector”button, pressed for
approximately 5 seconds,
until you hear 3 short beeps.
The cycle Indicator light will
come off and at this point,
all the settings will have been
cancelled. You are now free
to re-set the correct wash cycle.
You've left out a dish?
Interrupt the wash cycle by
opening the appliance door
with the utmost care, as
usual, then insert the dish
you had forgotten. When you
shut the appliance door, the
cycle will start up from where
you interrupted it.
Cycle end
The end of the wash cycle
is indicated by a double
beep and the flashing of the
wash cycle indicator light.
Warning:
Open the dishwasher door,
press the ON-OFF button,
unplug the appliance from
the electricity socket to cut
off the power supply; the
power supply cable should
consequently be easily
accessible.
Turn off the water tap.
Wait a few minutes before
unloading the dishes: they
are very hot! If you wait a little while, they dry better due
to the steam.
Empty the lower rack first.
The wash cycle stops and
then restarts when the
electricity comes back on or
when you close the door.
Delayed start
It is possible to delay the
start time of the cycle by 2,
4 or 6 hours.
1. Press the DELAYED
START button: every time
the button is pressed, a beep
is emitted and the selected
delayed start indicator light
illuminates.
2. Select the wash cycle and
shut the door: after the beep
sounds, the timer begins
counting down.
3. Once this time has
elapsed, the indicator light
switches off and the wash
cycle begins.
To adjust the delay time and
select a smaller period of
time, press the DELAYED
START button. To cancel it,
press the button repeatedly
until the selected delayed
start indicator light switches
off. The wash cycle will start
automatically as soon as the
door is shut.
D 1509)50-4
Programme Chart
Select the most suitable programme for the type of dishes and how dirty they are. To select the wash programme see
the chart below:
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce
the amount of detergent used accordingly.
The number and type of wash cycles and options may vary depending on the dishwasher model.
Wash cycle selection
instructions
Detergent
(A) = compartment A
(B) = compartment B
Wash cycle
Extremely soiled dishes
and pans (not to be
used for delicate items).
Drying
Wash cycle
duration
(tolerance
±10%)
Hrs. Min.
Powder
Liquid
Tablets
24 g (A)
3 g (B)
24 ml (A)
3 ml (B)
no
yes
2:00’
27 g (A)
27 ml (A)
no
yes
1:33’
24 g (A)
3 g (B)
24 ml (A)
3 ml (B)
no
yes
2:25’
20 g (A)
20 g (A)
no
yes
0:44’
no
no
no
no
0:12'
20 g (A)
20 g (A)
no
yes
1:30’
Super Wash
Normally soiled pans
and dishes. Standard
daily wash cycle.
Normal
Environmentallyfriendly* wash cycle
with low energy
consumption levels,
suitable for pans and
dishes.
Economic and fast cycle
to be used for slightly
dirty dishes. Run cycle
immediately after use.
Preliminary wash cycle
for dishes while the load
is awaiting completion
with the dishes from the
next meal.
Special cycle to be used
for more delicate items
which are sensitive to
high temperatures. Run
cycle immediately after
use.
Eco*
Rapid & Dry
Soak
Crystal
Note:
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid
1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid
To optimise wash performance and save on energy, try yo use the dishwasher with a full wash load. If it takes
some time to fill your dishwasher, use the soak cycle to avoid caked on food and build up of bad odours.
*The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it
uses less energy and is les harmful to the environment.
9
D 1509)50-4
Before Using your Dishwasher
Adjusting the water
softener.
Hardness of the water
Your dishwasher can adjust
its salt consumption according to the hardness of the
water in your home. This
way, you can optimise and
customise your dishwasher's
salt consumption.
To adjust salt consumption,
do as follows:
1. Unscrew the salt container
cap
2. There is an arrow on the
neck of the container (see
figure): if necessary, turn
the arrow anti-clockwise
from the "-" setting to the
"+" setting.
Select the arrow position
depending on the water
hardness, referring to the
table.
Salt
Filling the salt container.
Always use salt which is
intended for dishwasher use.
The salt container is situated
underneath the lower basket,
fill it up as follows:
1.Pull out the lower basket
completely, unscrew and
remove the container cap
2. If it is the first time you
add the salt, first fill the
container up with water
(you won't have to do this
again next time)
3. Put the dishwasher funnel
on the hole and pour in
approximately two kilos of
salt. It is normal that some
water comes out of the
container.
4. Screw the cap back in
place carefully.
10
To prevent rust
from forming, load
the salt just before
Selector beginning
Salt
aAutonomy
wash
knob
consumption
c y c l e .(cycles/2 kg)
position
(grams/cycle)
0 - 1.7
/
0
/
10 – 25 18 – 44
1.8 – 4.4
-
20
60
25 – 50 45 – 89
4.5 – 8.9
MED
40
40
> 8.9
+
60
25
°dH
°fH
°mmol/l
0 - 10
0 - 17
> 50
> 89
You don't know how
hard the water in your
home is? Ask the
company that supplies
water in your area.
When to add salt.
The salt container should be
filled up when the low salt
indicator light flashes on the
control panel. Your appliance
will remind you to do so for 5
consecutive wash cycles.
When necessary, measure
out the salt before a wash
cycle so that any saline
solution which has leaked
out of the salt dispenser is
removed.
D 1509)50-4
Before Using your Dishwasher
The detergent
Adding detergent
To open lid A, press button
B.
The detergent should be put
into the two containers C and
D.
If using a tablet, put it in
container "D".
Now you can close the lid:
press it down until you hear
it click.
B
D
Only use products
which have been
specifically designed for
dishwashers.
Do not use table salt or
industrial salt, or washing
up liquid.
C
• To obtain the best results
from each washing and
drying cycle, powder
detergent, rinse aid liquid
and salt should be used.
If it won't close
Check whether there is any
detergent residue on the
edges of the dispenser.
Remove the excess.
• Use the right amount of
detergent (see programme
chart).
• Store your detergent and
rinse aid in a cool, dry
place, safely away from
children.
A
Rinse aid.
Rinse aid makes dishes
sparkle more as it improves
their drying. The rinse aid
container is situated on the
inside of the appliance door,
you should refill it when light
“D” indicates that it is empty.
(If your dishwasher is fitted
with a “low rinse aid”
indicator light, fill the
container up when the
indicator light flashes or
lights up).
Filling the rinse aid
container.
To open the dispenser, turn
cap C anticlockwise. Take
care when you pour in the
rinse aid to avoid it
overflowing. You can
regulate the amount of rinse
aid used by the dishwasher,
move the adjuster F which
you will find under lid C.
F
C
D
- The amount of rinse aid
needs to be increased if
the dishes appear dull or
you can see circular stains.
- The amount of rinse aid
needs to be reduced if the
dishes are sticky or you
can see white streaks.
You can choose from six different
positions. It is normally set to 4.
Warning
Three-in-one dishwasher tablets are now available on the market, and combine detergent, salt and rinse aid all in one.
If the water in your area is hard or very hard, we still recommend you pour extra salt into the relevant dispenser to prevent
the formation of white streaks on your dishes or on the interior of the appliance.
Using a three-in-one product means it is no longer necessary to put rinse aid into the relevant container.
If you want to achieve perfectly dry dishes, you may add rinse aid as long as the dosage adjuster is set to no.2.
In any case, please read the manufacturer's instructions on the packet.
If you use only these products, it is normal for the salt and rinse aid indicator lights to flash permanently after a certain
number of cycles.
11
D 1509)50-4
Loading your Dishwasher
First of all.
Before placing dishes in the
baskets, remove all course
food remains. This avoids
blocking the filter, which would
reduce the efficiency of the
wash.
If saucepans and frying pans
are very dirty, allow them to
soak before being washed.
To make it easier to load your
dishes, pull the baskets out.
What goes into the lower
basket?
The lower rack can hold pans,
lids, plates, salad bowls,
cutlery, etc. as seen in the
Loading examples.
Plates and large covers
should be placed at the sides
of the rack, ensuring that they
do not block the rotation of the
upper sprayer arm.
Some dishwasher models are
fitted with tip-up sections,
which can be used in a vertical
position when arranging
plates or in a horizontal
position when arranging pans
and salad bowls.
After loading the dishes,
remember to check that the
spray arms can turn freely
without hitting against any
dishes.
Load examples
upper basket
upper basket
What goes into the upper
basket?
Place
delicate
and
lightweight dishes in the
upper basket: glasses, tea
cups and coffee cups,
saucers and plates - shallow
salad bowls, slightly dirty
frying pans and shallow
pans.
Position lightweight dishes in
such as way as to avoid their
being moved by the spray of
water.
lower basket
lower basket
How to adjust the upper
basket.
The upper basket can be set
in high or low position to
enable you to organise your
dishes effortlessly.
1
2
If the rack is equipped with
the click clack handles* (see
figure), pull them upwards or
downwards to adjust the
height.
Fig. A
The cutlery basket
Knives and other utensils with
sharp edges must be placed
in the cutlery basket with the
points facing downwards, or
they must be positioned
horizontally in the tip-up
compartments on the upper
rack. Position all cutlery items
so that they don't touch.
if the basket is the one with
side inserts, then insert the tea
spoons one by one into the
slots (see figure A).
It is best if you place longer
utensils horizontally at the front
of the upper basket. The grille
element may be positioned in
the basket to separate the
cutlery: place the pieces of cutlery into the appropriate
compartments with the
handles at the bottom.
12
What can I Wash Items not suitable for the dishwasher:
• Cutlery and tableware made from wood or part wood - They may become faded and
unsightly in appearance.
• Avoid washing horn handled and bronze cutlery in the machine.
• Delicate/decorative glassware and vases, special antique or irreplaceable china - the
decorative patterns printed on these items will not be dishwasher proof.
• Plastic objects that are not resistant to hot water.
• Copper and Pewter utensils. Aluminium and Sliver objects.
• Some types of glass can become opaque in appearance after they have been washed
too many times in a dishwasher.
• Highly absorbent materials such as sponges and towels should never be placed in a
dishwasher.
• If in any doubt, check with the manufacturer on items suitability for dishwasher’s.
WARNING: Dishes or cutlery soiled with tobacco ash, wax, lubricating grease or
paint should not be put in the dishwasher.
Our recommendation: In future, only purchase table or kitchenware that has been
confirmed - dishwasher proof.
D 1509)50-4
Care and Cleaning
Unplug the appliance.
Before carrying out any
cleaning or maintenance on
the dishwasher, always
remove the plug from the
electricity socket.
After every wash.
When the wash cycle has
ended, always remember to
turn off the water supply tap
and to leave the appliance
door ajar. This way, moisture
and bad odours will not be
trapped inside.
The filter assembly
• If you want consistent
good results from your
dishwasher, you need to
clean the filter assembly.
• Remove the larger food
particles trapped inside the
cup “C” and the semi-circular
filter A after each wash; pull
the cup handle upwards to
remove them. Just rinse
them under running water.
• The entire filter assembly
should
be
cleaned
thoroughly once a month:
cup C + semi-circular filter
A + cylindrical filter B. Rotate filter “B” anticlockwise to
remove it.
1
B
2
A
C
Cleaning the spray arms.
Food residue may become
encrusted onto the spray
arms and block the holes
where water comes out.
Check the spray arms
regularly and clean them
once in a while.
DO NOT use solvents
or abrasives to clean the
exterior and rubber parts of
your appliance, do not use
solvents or abrasive cleaning
products. Use a cloth
dampened with lukewarm
soapy water only.
If there are any stains on the
surface of the appliance
interior, use a cloth
dampened with water and a
little white vinegar, or a
cleaning product specifically
made for dishwashers.
Going away
If the dishwasher is not
going to be used for some
time, carry out the
following:
• run a cycle with the
dishwasher empty.
• switch off at the electrical
socket and unplug.
• turn off the water supply
tap, disconnect the inlet
hose and allow to drain.
• fill the rinse aid
dispenser.
• leave the door ajar, to
prevent the build up of
unpleasant odours
inside the dishwasher.
The seals.
One of the factors that cause unpleasant odours to form
inside the dishwasher is food
that remains trapped in the
seals. Periodic cleaning
using a damp sponge will
prevent this from occurring.
Disconnecting
the
dishwasher.
When disconnecting the
dishwasher it is important
that tasks are carried out in
the correct sequence.
• switch off at the mains and
remove the plug from the
socket.
• turn off the water supply.
• disconnect drain and water
inlet hose.
• pull out the dishwasher,
carefully, withdrawing
hoses at the same time.
Before using the dishwasher
after a long break, plug in
and switch on at the
electrical socket. Reconnect
the inlet hose and turn on the
water supply tap. Check
there are no deposits of rust
inside the water pipe, if there
are allow water to run from
the supply tap for a few
minutes.
Moving the appliance.
Drain water from the
dishwasher. Secure all loose
parts. Only transport in an
upright position.
• If not kept upright during
transport, any water
remaining inside may
seep into the control
module and cause
subsequent errors with
programme functions.
For cleaning, use a non
metallic brush.
Reassemble the filter parts
(as shown in the figure) and
reinsert the whole assembly
into the dishwasher. Position
it into its housing and press
downwards.
The dishwasher is not to be
used without filters. Improper
replacement of the filters
may reduce the efficiency of
the wash and even damage
your dishwasher.
13
D 1509)50-4
Troubleshooting
Caution
- Do not forget that repairs should only be carried out by a qualified specialist. Improper repairs can lead to considerable equipment
damage, as well as danger to the user.
- The dishwasher must first be disconnected from the electricity supply before any repairs or other work can be carried out. Switch off at the
mains socket and water supply and remove the plug.
Resolving minor problems yourself.
Experience has shown that you can resolve most problems that arise during normal daily usage yourself, without having
to call out a service engineer. Not only does this save costs but it also means the appliance is available for use again
that much sooner. The following list of common occurences and their remedies should help you identify the causes of
most problems.
If the dishwasher won't
start, check...
■ Is the dishwasher plugged
in at the electricity socket
and switched on?
■ Is there a power failure,
check other appliances.
■ Check the fuse.
■ Is the water supply tap
turned on?
■ Is the water inlet hose
connected properly?
■ Is the pressure of the
water supply sufficient?
■ Is the inlet hose kinked?
■ Is the filter on the water
supply hose blocked?
■ Is the dishwasher door
not closed properly?
If water remains inside the
dishwasher, check...
■ the drain hose is not
kinked.
■ the drain syphon is not
obstructed.
■ the dishwasher filters are
not clogged.
If the dishes are not being
cleaned properly, check...
■ the correct amount of
detergent has been added.
■ there is regenerating salt
in the salt container.
■ the dishes have been
loaded correctly.
■ the selected programme
is suitable for the type of
dishes and the degree of
soiling.
■ all filters are clean and
positioned correctly.
■ the spray arm nozzles are
not obstructed.
■ there
is
nothing
obstructing the rotation of
the spray arms.
14
If the dishes fail to dry or
remain dirty, check...
■ there is rinse aid inside the
rinse aid container.
■ the rinse aid dispenser
setting is correct.
■ the detergent being used
is of good quality and has
not lost its effectiveness
(for example, through
incorrect storage, with the
box left open).
If the dishes show signs of
streaking, staining etc.
check...
■ the rinse aid dispenser
setting is not set too high.
If there are visible traces
of rust inside the tank,
check...
■ the cap off the salt
container is securely
closed and that the water
softner setting is correct.
■ the correct amount of
detergent is being used.
Certain detergents can be
more corrosive than
others.
■ the tank is made of steel
and therefore any rust
marks are due to external
elements (fragments of
rust from the tank pipes,
pots, cutlery etc.) Special
products
are
commercially available to
remove such marks.
Error messages
Your dishwasher is equipped
with a safety system which
is able to detect operating
faults.
These faults are reported by
one or two cycle indicator
lights flashing rapidly. Take
a note of which lights are
flashing, turn the appliance
off and call Hotpoint Service
for technical assistance.
Tap off alarm
If you have forgotten to turn
the water tap on, your appliance will remind you of this
by sounding a few short
beeps for a few minutes.
Turn the tap on and your appliance will start up again after a few minutes. Were you
to be absent when these
beeps are sounded, the appliance will be blocked automatically and cycle 3 and 4
indicator lights (eco and
rapid&dry cycle) will flash
rapidly. Turn the appliance
off at the ON-OFF button,
turn on the water tap and
wait approximately 20 seconds before turning the appliance back on.
Re-select the wash cycle and
the appliance will start up
again.
Clogged filter alarm
If the appliance is blocked
and indicator lights 2 (Normal)
and 4 (Rapid & dry) flash rapidly, this means the filter is
clogged by large particles of
food residue. Turn the appliance off, clean the filter thor-
oughly and reposition it in its
seat as illustrated on page
13. Then turn it back on.
Repeat the programming operations and the selected
wash cycle will start up
again.
Water load solenoid
valve malfunction alarm.
If indicator light 3 (eco
cycle) flashes rapidly, turn
the dishwasher off and back
on again after one minute.
If the alarm persists, first
turn off the water tap to
avoid any flooding and then
cut off the electricity supply
and call for technical
assistance.
If after all the checks, the
appliance still does not operate or the problem persists, call Hotpoint Service
(see KEY CONTACTS,
back page) and inform them
of:
- the type of problem
- the abbreviation of the
model name (Mod.) and the
relative numbers (S/N) written on the rating plate
located on the inner edge of
the door.
Switch off at the mains
socket and remove the plug.
Turn off the water supply.
D 1509)50-4
INFORMATION FOR TEST LABS
Load for 9 Standard Settings tests (upper basket at lower position)
Lower basket
Upper basket
,
$
'
'
*
)
i
g
$
h
!
k
!
e
!
!
e
)
+
'
e
f
g
!
Lower basket
Item
Diameter Volum
(approximately)
Type
Item
Diameter/Volum
(approximately)
A
B
soupe plate
23 cm.
cup
0,20 l.
dinner plate
26 cm.
e
f
19 cm.
dessert
plate
oval platter
19 cm.
g
serving
bowl
glass
250 ml.
32 cm.
h
k
saucer
14 cm.
serving
bowl
serving
bowl
13 cm.
C
D
Loading the Rinse Aid
The amount of rinse aid used for each cycle can
be regulated by turning the dose adjuster ‘F’ which
you will find under lid ‘C’.There are 6 different
settings; the normal dosage is setting 5.
Upper basket
Type
i
Loading the detergent
The cleaning detergent should be introduced into
the two containers “Comp.2” and “Comp.3 (see
table at the end of the page).
16 cm.
If the cutlery basket is
equipped with one
removable grid: insert
the cutlery one by one
into the slots, with the Salt adjustment
handles at the bottom.
Hardness of the water
Position them so that
°dH
°fH
°mmol/l
they don't touch.
EN 50242
Selector
knob
position
Salt
consumption
(grams/cycle)
Autonomy
(cycles/2 kg)
0 - 10
0 - 17
0 - 1.7
/
0
/
10 – 25
18 – 44
1.8 – 4.4
-
20
60
25 – 50
45 – 89
4.5 – 8.9
MED
40
40
> 50
> 89
> 8.9
+
60
25
Cycle
Total detergent
Comp.2
Comp.3
Eco
27 gr.
24 gr.
3 gr.
15
D 1509)50-4
After Sales Service
"No company is better positioned to offer an after sales service on a
Hotpoint appliance than us - the manufacturer"
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts and labour
guarantee for the first 12 months. In addition to this you also have the advantage of free
replacement parts for the first 5 years when fitted by a Hotpoint
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales service options:
Repair Service and Information Help Desk
UK: 08709 066066
www.theservicecentre.co.uk
Republic of Ireland: 1850 302 200
Note: Our operators will require the Model number and the Serial number of your appliance.
Available 364 days a year with a fast, effective and value for money service. We have the largest white goods repair
service in the UK with over 1200 of our own fully trained engineers. All repairs include a parts and labour guarantee for
12 months from the date of the repair.
If you require any information or have any questions about your appliance, our operators are on hand with help and
advice.
All this ensures that you will receive the best available after sales service possible.
Extended Warranties
UK: 08709 088 088
www.theservicecentre.co.uk
Republic of Ireland: 1850 502 200
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover plans to give
you total peace of mind.
●
Repair Protection Plan
-
FREE service repairs for a single Hotpoint appliance during the period of cover.
●
Kitchen Cover
-
FREE service repairs for all your Hotpoint appliances less than 8 years old.
Genuine Parts and Accessories UK: 08709 077 077
www.theservicecentre.co.uk
Republic of Ireland: (01) 842 6836
A wide range of genuine parts and accessories are available from our hotline or through our web site.
Genuine parts and accessories, extended warranties and service repairs are all
available on our web-site at:
www.theservicecentre.co.uk
16
D 1509)50-4
Guarantee
"Satisfaction guaranteed or your money back"
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair
service or visit our web-site at www.theservicecentre.co.uk and where necessary, we will arrange
for an engineer to call. If the technical problem is not resolved under this guarantee, we will
replace your machine or, if you prefer, give you your money back.
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free
replacement parts for the first 5 years (except microwaves, selected integrated appliances and
cooker hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint
engineer.
Guarantee terms and conditions
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to
the following provisions that your appliance:
●
Has been installed and used correctly in accordance with this instruction booklet.
●
Has been used solely for domestic purposes and is located on domestic premises (ie. not
for commercial or trade use).
●
Has been properly connected to a suitable electrical supply voltage as stated on the
appliance rating plate.
●
Has not been subject to misuse, accident, modified or repaired by anyone other than one of
our own service engineers.
For pre purchase information on any other Hotpoint product call: 08701 50 60 70
or visit: www.hotpoint.co.uk
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to
use quality recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the
appliance. Dispose of these parts separately to ensure that the appliance can no longer be
plugged into a mains socket and the door cannot be locked shut.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that
old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream.
Old appliances must be collected separately in order to optimise the recovery and recycling of the materials
they contain and reduce the impact on human health and the environment. The crossed out "wheeled bin"
symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or retailer for information concerning the correct disposal of
their old appliance.
17
D 1509)50-4
NOTES
18
D 1509)50-4
NOTES
19
Key Contacts
After Sales Service
Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in
both the appliances and services we offer.
Repair Service and Information Desk
UK: 08709 066 066
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
www.theservicecentre.co.uk
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number:
Serial number:
Extended Warranties
UK: 08709 088 088
(Open 8 to 8 Mon - Sun)
www.theservicecentre.co.uk
Republic of Ireland: 1850 502 200
Genuine Parts and Accessories
UK: 08709 077 077
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)
www.theservicecentre.co.uk
Republic of Ireland: (01) 842 6836
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.
195066853.00
September 2007