advertisement
▼
Scroll to page 2
of 24
Instructions for use WASHING MACHINE Contents GB English,1 PT Português,13 GB Installation, 2-3 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data Description of the washing machine and starting a wash cycle, 4-5 Control panel Indicator lights Starting a wash cycle Wash cycles, 6 Table of wash cycles Personalisation, 7 ARXXL 129 S Setting the temperature Setting the spin speed Functions Detergents and laundry, 8 Detergent dispenser drawer Bleach cycle Preparing the laundry Garments requiring special care Load balancing system Precautions and tips, 9 General safety Disposal Opening the porthole door manually Care and maintenance, 10 Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Troubleshooting, 11 Service, 12 1 Installation GB This instruction manual should be kept in a safe place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features. Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washing machine. Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance. Connecting the electricity and water supplies Unpacking and levelling Connecting the water inlet hose Unpacking 1. Remove the washing machine from its packaging. 2. Make sure that the washing machine has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process. 3. Remove the 4 protective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure). 4. Close off the holes using the plastic plugs provided. 5. Keep all the parts in a safe place: you will need them again if the washing machine needs to be moved to another location. Packaging materials should not be used as toys for children. Levelling 1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or anything else. 2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°. 2 A 1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 gas threaded opening (see figure). Before performing the connection, allow the water to run freely until it is perfectly clear. 2. Connect the inlet hose to the washing machine by screwing it onto the corresponding water inlet of the appliance, which is situated on the top righthand side of the rear part of the appliance (see figure). 3. Make sure that the hose is not folded over or bent. The water pressure at the tap must fall within the values indicated in the Technical details table (see next page). If the inlet hose is not long enough, contact a specialised shop or an authorised technician. Never use second-hand hoses. Use the ones supplied with the machine. Do not use extension cords or multiple sockets. Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor; GB The cable should not be bent or compressed. The power supply cable must only be replaced by authorised technicians. Warning! The company shall not be held responsible in the event that these regulations are not respected. The first wash cycle alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater. We advise against the use of hose extensions; if it is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length. Electrical connections Before plugging the appliance into the electricity socket, make sure that: the socket is earthed and complies with all applicable laws; the socket is able to withstand the maximum power load of the appliance as indicated in the Technical data table (see opposite); the power supply voltage falls within the values indicated in the Technical data table (see opposite); the socket is compatible with the plug of the washing machine. If this is not the case, replace the socket or the plug. The washing machine must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain, storms and other weather conditions. When the washing machine has been installed, the electricity socket must be within easy reach. Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using the wash cycle 1. Technical data Model ARXXL 129 S Dimensions width 59.5 cm height 85 cm depth 53,5 cm Capacity from 1 to 7 kg Electrical connections please refer to the technical data plate fixed to the machine Water connections maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 52 litres Spin speed up to 1200 rotations per minute Energy rated programmes according to regulation EN 60456 programme 6; temperature 60°C; using a load of 7 kg. This appliance conforms to the following EC Directives: - 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent modifications - 2002/96/EC - 2006/95/EC (Low Voltage) 3 Description of the washing machine and starting a wash cycle Control panel GB WASH CYCLE PROGRESS/ DELAY TIMER indicator lights SPIN SPEED knob ON/OFF button TEMPERATURE indicator light knob START/PAUSE Detergent dispenser drawer FUNCTION WASH CYCLE knob Detergent dispenser drawer: used to dispense detergents and washing additives (see Detergents and laundry). There is a key which provides a summary of the available wash cycles inside the detergent dispenser drawer; this may be consulted at any time. ON/OFF button: switches the washing machine on and off. WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move. FUNCTION buttons with indicator light: used to select the available functions. The indicator light corresponding to the selected function will remain lit. TEMPERATURE knob: sets the temperature or the cold wash cycle (see Personalisation). SPIN SPEED knob: sets the spin speed or exclude the spin cycle completely (see Personalisation). 4 DOOR LOCKED buttons with indicator lights button with indicator light WASH CYCLE PROGRESS/DELAY TIMER indicator lights: used to monitor the progress of the wash cycle. The illuminated indicator light shows which phase is in progress. If the Delay Timer function has been set, the time remaining until the wash cycle starts will be indicated (see next page). DOOR LOCKED indicator light: indicates whether the door may be opened or not (see next page). START/PAUSE button with indicator light: starts or temporarily interrupts the wash cycles. N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the indicator light is switched off, the DOOR LOCKED door may be opened. To start the wash cycle from the point at which it was interrupted, press this button again. Indicator lights The indicator lights provide important information. This is what they can tell you: Delayed start If the DELAY TIMER function has been activated (see Personalisation), after the wash cycle has been started the indicator light corresponding to the selected delay period will begin to flash: Wash cycle phase indicator lights Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress. Wash Rinse Spin Drain End of wash cycle As time passes, the remaining delay will be displayed and the corresponding indicator light will flash: Once the set delay has elapsed, the flashing indicator light will switch off and the selected wash cycle will begin. Function buttons and corresponding indicator lights When a function is selected, the corresponding indicator light will illuminate. If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated. If a function which is incompatible with another function selected previously, only the most recent selection will remain active. Door locked indicator light If this indicator light is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damage, wait for the indicator light to switch off before you open the appliance door. N.B. If the DELAY TIMER function is activated, the door cannot be opened; pause the machine by pressing the START/PAUSE button if you wish to open it. If the START/PAUSE indicator light (orange) flashes rapidly at the same time as the function indicator light, this indicates a problem has occurred (see Troubleshooting). Starting a wash cycle 1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then they will switch off and the START/PAUSE indicator light will pulse. 2. Load the laundry and close the door. 3. Set the WASH CYCLE knob to the desired programme. 4. Set the washing temperature (see Personalisation). 5. Set the spin speed (see Personalisation). 6. Measure out the detergent and washing additives (see Detergents and laundry). 7. Select the desired functions. 8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle. indicator light will switch on. The DOOR LOCKED indicator light will switch 9. At the end of the wash cycle the off, indicating that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch the washing machine off by pressing the ON/OFF button. 5 GB Wash cycles Table of wash cycles Wash cycles GB Detergents Max temp. (°C) Max. speed (rpm) Bleach Wash Fabric softener 90° 1200 l l l 7 170 60° 1200 - l l 7 153 7 Goodnigt cycle: Lightly soiled delicate colours. 8 Baby cycle: Heavily soiled delicate colours. 40° 800 - l l 4 290 40° 800 - l l 2 118 9 Shirts 40° 600 - l l 2 70 10 Silk/Curtains: For garments in silk and viscose, lingerie. 11 Wool: For wool, cashmere, etc. 30° 0 - l l 2 55 40° 600 - l l 1,5 55 Description of the wash cycle Max. load (kg) Cycle duration Special cycles 6 Sanitizing cycle: Extremely soiled whites. 6 Sanitizing cycle (1): Heavily soiled whites and resistant colours. Everyday wash cycles (Daily) 1 Cotton: Heavily soiled whites and resistant colours. 1 Cotton (2): Heavily soiled whites and delicate colours. 2 Coloured Cottons (3): Lightly soiled whites and delicate colours. 3 Synthetics resistents: Heavily soiled resistant colours. 3 Synthetics delicates: Lightly soiled resistant colours. Mix 30': To refresh lightly soiled garments quickly (not suitable 4 for wool, silk and clothes which require washing by hand). Mix 15': To refresh lightly soiled garments quickly (not suitable 5 for wool, silk and clothes which require washing by hand). 60° 1200 l l l 7 122 40° 1200 l l l 7 115 40° 1200 l l l 7 85 60° 800 - l l 3 85 40° 800 - l l 3 70 30° 800 - l l 3 30 30° 800 - l l 1,5 15 - 1200 - - l 7 36 Partial wash cycles A Rinse B Light rinse - 800 - - l 3 31 C Spin D Light spin - 1200 - - - 7 16 - 800 - - - 3 12 E Drain no spin - 0 - - - 7 2 The information contained in the table is intended as a guide only. For all Test Institutes: 1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 6 with a temperature of 60°C. 2) Long wash cycle for cottons: set wash cycle 1 with a temperature of 40°C. 3) Short wash cycle for cottons: set wash cycle 2 with a temperature of 40°C. Specials wash cycles Sanitizing cycle (wash cycle 6). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach. Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled Detergent dispenser drawer). Goodnigt cycle (wash cycle 7). This is a silent cycle which can be run at night, when the electricity prices are lower. The wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water in the drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin cycle and drain the water automatically after 8 hours. Baby cycle (wash cycle 8). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special disinfecting additives added to the detergent. At the end of the wash cycle, the machine will slowly rotate the drum to prevent the formation of creases; to end the cycle press the START/PAUSE button. Mix 30(wash cycle 4) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and therefore saves both energy and time. By selecting this wash cycle (4 at 30°C), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 3 kg. Mix 15(wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics together (except for wool and silk items), with a maximum load of 1.5 kg. 6 Personalisation Setting the temperature GB Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles). The temperature may be lowered, or even set to a cold wash ( ). The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle. Setting the spin speed Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle. The maximum spin speeds available for each wash cycle are as follows: Wash cycles Maximum spin speed Cottons 1200 rpm Synthetics 800 rpm Wool 600 rpm Silk drain only The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol . The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed set for each wash cycle. Functions The various wash functions available with this washing machine will help to achieve the desired results, every time. To activate the functions: 1. Press the button corresponding to the desired function; 2. the function is enabled when the corresponding indicator light is illuminated. Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the selected wash cycle. Delay timer This timer delays the start time of the wash cycle by up to 12 hours. Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button is pressed, the function will be disabled. N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it. This option is enabled with all programmes. Easy iron By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end of the cycle the washing machine will perform slow rotations of the drum; the EASY IRON and START/ phase will remain lit in a fixed manner. To end the cycle, press PAUSE indicator lights will flash (orange) and the the START/PAUSE button or the EASY IRON button. For the Silk wash cycle, the machine will end the cycle while the laundry is soaking, the EASY IRON and START/ PAUSE indicator lights will flash (orange) and the RINSE phase will remain lit in a fixed manner. To drain the water so that the laundry may be removed, press the START/PAUSE button or the EASY IRON button. This function may not be used in conjunction with wash cycles 4, 5, 6, 7, 8, 11, C, D, E. Extra rinse By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly useful for sensitive skin. This function may not be used in conjunction with wash cycles 4, 5, C, D, E. Super Wash Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this function offers a high-performance wash. This function may not be used in conjunction with wash cycles 4, 5, 6, 10, 11, A, B, C, D, E. 7 Detergents and laundry GB Detergent dispenser drawer Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution. Do not use hand washing detergents because these create too much foam. Open the detergent dispenser drawer and 3 pour in the detergent or washing additive, as follows. MAX 1 2 compartment 1: Detergent for the wash cycle (powder or liquid) Liquid detergent should only be poured in immediately prior to the start of the wash cycle. compartment 2: Additives (fabric softeners, etc.) The fabric softener should not overflow the grid. extra compartment 3: Bleach Bleach cycle Bleaching may only be performed in conjunction with wash cycles 1, 2, 6. Pour the bleach into extra compartment 3; pour the detergent and softener into the corresponding compartments, then select one of the abovementioned wash cycles. This option is recommended only for very soiled cotton garments. Preparing the laundry Divide the laundry according to: - the type of fabric/the symbol on the label - the colours: separate coloured garments from whites. Empty all garment pockets and check the buttons. Do not exceed the listed values, which refer to the weight of the laundry when dry: Durable fabrics: max. 7 kg Synthetic fabrics: max. 3 kg Delicate fabrics: max. 2 kg Wool: max. 1.5 kg 8 How much does your laundry weigh? 1 1 1 1 1 sheet 400-500 g pillow case 150-200 g tablecloth 400-500 g bathrobe 900-1200 g towel 150-250 g Garments requiring special care Shirts: use special wash cycle 9 to wash shirts in various fabrics and colours. It guarantees maximum care is taken of the garments and minimises the formation of creases. Silk: use special wash cycle 10 to wash all silk garments. We recommend the use of special detergent which has been designed to wash delicate clothes. Curtains: fold curtains and place them in a pillow case or mesh bag. Use wash cycle 10. Wool: Hotpoint/Ariston is the only washing machine manufacturer to have been awarded the prestigious Woolmark Platinum Care endorsement (M.0508) by the Woolmark Company, which means that all woollen garments may be washed in the washing machine, even those which state hand wash only on the label. Wash cycle 11 therefore offers complete peace of mind when washing woollen garments in the washing machine (max. load 1.5 kg) and guarantees optimal performance. Load balancing system Before every spin cycle, to avoid excessive vibrations and to distribute the load in a uniform manner, the drum rotates continuously at a speed which is slightly greater than the washing rotation speed. If, after several attempts, the load is not balanced correctly, the machine spins at a reduced spin speed. If the load is excessively unbalanced, the washing machine performs the distribution process instead of spinning. To encourage improved load distribution and balance, we recommend small and large garments are mixed in the load. Precautions and tips This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. Opening the porthole door manually General safety This appliance was designed for domestic use only. The washing machine must only be used by adults, in accordance with the instructions provided in this manual. Do not touch the machine when barefoot or with wet or damp hands or feet. Do not pull on the power supply cable when unplugging the appliance from the electricity socket. Hold the plug and pull. Do not open the detergent dispenser drawer while the machine is in operation. Do not touch the drained water as it may reach extremely high temperatures. Never force the porthole door. This could damage the safety lock mechanism designed to prevent accidental opening. GB In the event that it is not possible to open the porthole door due to a powercut, and if you wish to remove the laundry, proceed as follows: 20 1. remove the plug from the electrical socket. 2. make sure the water level inside the machine is lower than the door opening; if it is not, remove excess water using the drain hose, collecting it in a bucket as indicated in the figure. 3. using a screwdriver, remove the cover panel on the lower front part of the washing machine (see figure). If the appliance breaks down, do not under any circumstances access the internal mechanisms in an attempt to repair it yourself. Always keep children well away from the appliance while it is operating. The door can become quite hot during the wash cycle. If the appliance has to be moved, work in a group of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy. Before loading laundry into the washing machine, make sure the drum is empty. Disposal Disposing of the packaging materials: observe local regulations so that the packaging may be re-used. The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment, requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out "wheeled bin" symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. 4. pull outwards using the tab as indicated in the figure, until the plastic tie-rod is freed from its stop position; pull downwards and open the door at the same time. 5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance. 9 Care and maintenance GB Cutting off the water and electricity supplies Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks. Unplug the washing machine when cleaning it and during all maintenance work. Cleaning the washing machine The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives. Cleaning the detergent dispenser drawer Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently. 1 2 Cleaning the pump The washing machine is fitted with a self-cleaning pump which does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber which protects the pump, situated in its bottom part. Make sure the wash cycle has finished and unplug the appliance. To access the pre-chamber: 1. using a screwdriver, remove the cover panel on the lower front part of the washing machine (see figure); 2. unscrew the lid by rotating it anti-clockwise (see figure): a little water may trickle out. This is perfectly normal; Caring for the door and drum of your appliance Always leave the porthole door ajar in order to prevent unpleasant odours from forming. 3. clean the inside thoroughly; 4. screw the lid back on; 5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance. Checking the water inlet hose Check the inlet hose at least once a year. If there are any cracks, it should be replaced immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open. Never use second-hand hoses. 10 Troubleshooting Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make sure that the problem cannot be not solved easily using the following list. GB Problem: Possible causes / Solutions: The washing machine does not switch on. The appliance is not plugged into the socket fully, or is not making contact. There is no power in the house. The wash cycle does not start. The washing machine door is not closed properly. The ON/OFF button has not been pressed. The START/PAUSE button has not been pressed. The water tap has not been opened. A delayed start has been set (see Personalisation). The washing machine does not take in water (the indicator light for the first wash cycle stage flashes rapidly). The water inlet hose is not connected to the tap. The hose is bent. The water tap has not been opened. There is no water supply in the house. The pressure is too low. The START/PAUSE button has not been pressed. The washing machine continuously takes in and drains water. The drain hose is not fitted at a height between 65 and 100 cm from the floor (see Installation). The free end of the hose is under water (see Installation). The wall drainage system is not fitted with a breather pipe. If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the Assistance Service. If the dwelling is on one of the upper floors of a building, there may be problems relating to water drainage, causing the washing machine to fill with water and drain continuously. Special anti-draining valves are available in shops and help to avoid this inconvenience. The washing machine does not drain or spin. The wash cycle does not include draining: some wash cycles require the drain phase to be started manually. The EASY IRON function has been activated: To complete the wash cycle, press the START/PAUSE button (Personalisation). The drain hose is bent (see Installation). The drainage duct is clogged. The washing machine vibrates a lot during the spin cycle. The drum was not unlocked correctly during installation (see Installation). The washing machine is not level (see Installation). The washing machine is trapped between cabinets and walls (see Installation). The washing machine leaks. The water inlet hose is not screwed on properly (see Installation). The detergent dispenser drawer is blocked (for cleaning instructions, see Care and maintenance). The drain hose is not fixed properly (see Installation). The START/PAUSE indicator light (orange) and the function indicator lights flash rapidly. Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again. If the problem persists, contact the Technical Assistance Service. There is too much foam. The detergent is not suitable for machine washing (it should display the text for washing machines or hand and machine wash, or the like). Too much detergent was used. 11 Service Before calling for Assistance: Check whether you can solve the problem alone (see Troubleshooting); Restart the programme to check whether the problem has been solved; If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. GB Always request the assistance of authorised technicians. Have the following information to hand: the type of problem; the appliance model (Mod.); the serial number (S/N). This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the front of the appliance by opening the door. 12 Instruções para utilização MÁQUINA DE LAVAR ROUPA Sumário PT Português PT Instalação, 14-15 Desembalar e nivelar Ligações hidráulicas e eléctricas Primeiro ciclo de lavagem Dados técnicos Descrição da máquina de lavar roupa e como iniciar um programa, 16-17 Painel de comandos Indicadores luminosos Iniciar um programa Programas, 18 Tabela dos programas Personalizações, 19 ARXXL 129 S Seleccione a temperatura Seleccione a centrifugação Funções Detergentes e roupa, 20 Gaveta dos detergentes Ciclo para branquear Preparar a roupa Peças especiais Sistema de balanceamento da carga Precauções e conselhos, 21 Segurança geral Eliminação Abertura manual da porta de vidro Manutenção e cuidados, 22 Interromper a alimentação de água e de corrente eléctrica Limpar a máquina de lavar roupa Limpar a gaveta dos detergentes Cuidados com a porta de vidro e o tambor Limpar a bomba Verificar o tubo de alimentação de água Anomalias e soluções, 23 Assistência, 24 13 Instalação PT É importante guardar este manual para poder consultá-lo a qualquer momento. Se a máquina for vendida, cedida ou transferida, certifique-se que este manual permaneça com a máquina para informar o novo proprietário acerca do seu funcionamento e das respectivas advertências. Um cuidadoso nivelamento dá estabilidade à máquina e evita vibrações, ruídos e deslocamentos durante o funcionamento. Se houver tapete ou alcatifa, regule os pés em modo que embaixo da máquina de lavar roupa deixe um espaço suficiente para ventilação. Leia com atenção estas instruções: há importantes informações acerca da instalação, da utilização e da segurança. Ligações hidráulicas e eléctricas Ligação do tubo de alimentação da água Desembalar e nivelar Desembalar 1. Tire a máquina de lavar roupa da embalagem. 2. Verifique se a máquina de lavar roupa sofreu danos no transporte. Se estiver danificada não efectue a sua ligação e contacte o revendedor. 3. Tire os 4 parafusos de protecção para o transporte e a borrachinha com o respectivo calço, situados na parte traseira (veja a figura). 4. Tampe os furos com as tampas em plástico fornecidas. 5. Guarde todas as peças: se for necessário transportar a máquina de lavar roupa, terão de ser montadas outra vez. Embalagens não são brinquedos para as crianças! Nivelamento 1. Instale a máquina de lavar roupa sobre um pavimento plano e rígido, sem encostá-la em paredes, móveis nem outro. 2. Se o pavimento não for perfeitamente horizontal, para compensar qualquer irregularidade, desatarraxe ou atarraxe os pés dianteiros (veja a figura); o ângulo de inclinação, medido no plano de trabalho, não deve ultrapassar 2°. 14 A 1. Coloque a guarnição A na ponta do tubo de alimentação e atarraxe-o numa torneira de água fria com bocal de rosca de 3/4 gás (veja a figura). Antes de realizar esta ligação, deixe a água escorrer até estar límpida. 2. Ligue o tubo de alimentação na máquina de lavar roupa atarraxando-o no apropriado fornecimento da água, na parte traseira, em cima à direita (veja a figura). 3. Tome cuidado para o tubo não ser dobrado nem esmagado. A pressão hídrica da torneira deve ser entre os valores da tabela dos Dados técnicos (veja a página ao lado). Se o comprimento do tubo de alimentação não for suficiente, contacte uma oficina especializada ou um técnico autorizado. Nunca utilize tubos já usados. Utilize aqueles fornecidos com a máquina. Ligação do tubo de descarga 65 - 100 cm Ligue o tubo de descarga, sem dobrá-lo, a um conduto de descarga ou a uma descarga de parede colocados entre 65 e 100 cm do chão; Não empregue extensões nem fichas múltiplas. PT O cabo não deve ser dobrado nem apertado. O cabo de alimentação deve ser substituído somente por técnicos autorizados. Atenção! O fabricante declina toda a responsabilidade se estas regras não forem respeitadas. Primeiro ciclo de lavagem em alternativa, coloque na beira de um lavabo ou de uma banheira, prendendo na torneira a guia fornecida (veja a figura). A ponta solta do tubo de descarga não deve permanecer emergida na água. É desaconselhado empregar tubos de extensão; mas se for indispensável, a extensão deve ter o mesmo diâmetro do tubo original e não medir mais de 150 cm de comprimento. Depois da instalação, antes de usar, efectue um ciclo de lavagem com detergente mas sem roupa, defina o programa 1. Dados técnicos Ligação eléctrica Antes de ligar a ficha na tomada eléctrica, certifiquese que: a tomada tenha uma ligação à terra e seja nos termos da legislação; a tomada tenha a capacidade para suportar a carga máxima de potência da máquina, indicada na tabela dos Dados técnicos (veja ao lado); a tensão de alimentação seja entre os valores indicados na tabela dos Dados técnicos (veja ao lado); a tomada seja compatível com a ficha da máquina de lavar roupa. Se não for, substitua a tomada ou a ficha. Esta máquina de lavar roupa não deve ser instalada ao aberto, nem mesmo abrigada, porque é muito perigoso deixá-la exposta à chuva e às tempestades. Depois de ter instalado a máquina de lavar roupa, o acesso à tomada eléctrica deve ser fácil. Modelo ARXXL 129 S Medidas largura 59,5 cm. altura 85 cm. profundidade 53,5 cm. Capacidade de 1 a 7 kg. Ligações eléctricas veja a placa das características técnicas colocada na máquina Ligações hídricas pressão máxima 1 MPa (10 bars) pressão mínima 0,05 MPa (0,5 bar) capacidade do tambor 52 litros Velocidade da centrifugação até 1.200 rotações por minuto Programas de controlo segundo a norma EN 60456 programa 6; temperatura 60°C; realizado com carga de 7 kg. Esta aparelhagem é em conformidade com as seguintes Directivas Comunitárias: - 89/336/CEE dl 03/05/89 (Compatibilidade Electromagnética) e posteriores modificações. - 2002/96/CE - 2006/95/CE (Baixa Tensão) 15 Descrição da máquina de lavar roupa e como iniciar um programa PT Painel de comandos Indicadores LUMINOSOS DE AVANÇO DO CICLO/ INÍCIO POSTERIOR Selector de CENTRIFUGAÇÃO Tecla de LIGA/ DESLIGA Selector da TEMPERATURA Gaveta dos detergentes Teclas com indicadores luminosos de FUNÇÕES Indicador luminoso PORTA BLOQUEADA Tecla com indicador luminoso INÍCIO/ PAUSA Selector de PROGRAMAS Gaveta dos detergentes: para colocar detergentes e aditivos (veja Detergentes e roupa). Dentro da gaveta dos detergentes está situado um indicador, com o qual é possível consultar em qualquer momento um esquema sintético dos programas. Tecla de LIGA/DESLIGA: para ligar e desligar a máquina de lavar roupa. Selector de PROGRAMAS: para programar os programas. Durante o programa o selector permanece parado. Teclas com indicadores luminosos de FUNÇÕES: para seleccionar as funções disponíveis. O indicador luminoso correspondente à função seleccionada permanecerá aceso. Selector de CENTRIFUGAÇÃO: para seleccionar a centrifugação ou desactivá-la (veja Personalizações). Selector da TEMPERATURA: para definir a temperatura ou a lavagem a frio (veja Personalizações). 16 Indicadores LUMINOSOS DE AVANÇO DO CICLO/ INÍCIO POSTERIOR: para seguir o estado do avanço do programa de lavagem. O indicador luminoso aceso indica a fase em curso. Se tiver sido seleccionada a função Início posterior, indicarão o tempo que falta para iniciar o programa (veja a página ao lado). Indicador luminoso PORTA BLOQUEADA: para saber se a porta de vidro pode ser aberta (veja a página ao lado). Tecla com indicador luminoso INÍCIO/PAUSA: para activar os programas ou interrompê-los momentaneamente. Obs.: para colocar em pausa a lavagem em curso, carregar nesta tecla, o respectivo indicador luminoso ficará intermitente com uma luz laranja enquanto aquele da fase em curso ficará aceso fixo. Se o estiver apagado, indicador PORTA BLOQUEADA será possível abrir a porta de vidro. Para fazer iniciar a lavagem do ponto em que foi interrompida, carregar novamente nesta tecla. Indicadores luminosos Os indicadores luminosos fornecem informações importantes. Vejamos o que significam: Início posterior Se tiver sido activada a função Início posterior (veja Personalizações) depois de ter iniciado o programa, começará a lampejar o indicador luminoso relativo ao atraso seleccionado. Indicadores luminosos fase em curso Uma vez seleccionado e iniciado o ciclo de lavagem desejado, os indicadores luminosos se acenderão progressivamente para indicar o estado de avanço: PT Lavagem Enxaguamento Centrifugação Descarga Final da Lavagem Com o passar do tempo será mostrado a atraso restante, mediante o respectivo indicador luminoso aceso intermitente: Depois de ter passado o atraso seleccionado, o indicador luminoso intermitente irá desligar-se e começará o programa estabelecido. Iniciar um programa Teclas função e respectivos indicadores luminosos Ao seleccionar uma função o respectivo indicador luminoso se acenderá. Se a função seleccionada não for compatível com o programa definido, o indicador luminoso se acenderá intermitente e a função não será activada. Se for seleccionada uma função incompatível com outra anteriormente seleccionada, permanecerá activa somente a última seleccionada. Indicador luminoso porta bloqueada: O indicador luminoso aceso indica que a porta está trancada para impedir aberturas acidentais; para evitar danos é necessário aguardar que o indicador luminoso se apague antes de abrir a porta. Obs.: se estiver activa a função INÍCIO POSTERIOR a porta não poderá ser aberta, para abrir, colocar a máquina em pausa carregando na tecla INÍCIO/PAUSA. A intermitência rápida do indicador luminoso INÍCIO/ PAUSA (laranja) contemporâneo ao indicador das funções, sinaliza uma anomalia (veja Anomalias e soluções). 1. Para ligar a máquina de lavar roupa, mete na tecla de LIGA/DESLIGA. Todos os indicadores luminosos se acenderão por alguns segundos, em seguida apagam-se e ficará intermitente o indicador luminoso INÍCIO/PAUSA. 2. Coloque a roupa dentro da máquina e feche a porta. 3. Seleccione mediante o selector de PROGRAMAS o programa que desejar. 4. Seleccione a temperatura de lavagem (veja as Personalizações). 5. Seleccione a velocidade de centrifugação (veja as Personalizações). 6. Colocar detergentes e aditivos (veja Detergentes e roupa). 7. Seleccionar as funções desejadas. 8. Iniciar o programa carregando na tecla INÍCIO/PAUSA e o respectivo indicador luminoso permanecerá aceso fixo de cor verde. Para anular o ciclo programado, colocar a máquina em pausa carregando na tecla INÍCIO/PAUSA e escolher um novo ciclo. . O indicador luminoso PORTA BLOQUEADA irá desligar-se indicado 9. No fim do programa, irá iluminar-se o indicador que a porta pode ser aberta. Retire a roupa lavada de dentro e deixe a porta entreaberta para deixar o tambor enxugar-se. Para desligar a máquina de lavar roupa, mete na tecla de LIGA/DESLIGA. 17 Programas Tabela dos programas Programas PT Descrição do Programa Velocità Temp. max. max. (rotações (°C) por minuto) Detergentes Lixívia Lavagem Amaciador Carga Duração max. ciclo (Kg) Programas Especiais 6 Higienização: peças brancas extremamente sujas. 6 Higienização (1): brancos e coloridos resistentes muito sujos. 90° 1200 l l l 7 170 60° 1200 - l l 7 153 7 Ciclo Boa Noite: coloridos delicados pouco sujos. 8 Ciclo Bébés: coloridos delicados muito sujos. 40° 800 - l l 4 290 40° 800 - l l 2 118 9 Camisas 40° 600 - l l 2 70 10 Seda / Cortinas: para roupas de seda, viscosa, lingerie. 11 Lã: para lã, cashmere, etc. 30° 0 - l l 2 55 40° 600 - l l 1,5 55 60° 1200 l l l 7 122 115 Programas para todos os dias (Quotidiano) 1 Algodão: brancos e coloridos resistentes muito sujos. 1 Algodão (2): brancos e coloridos delicados muito sujos. 40° 1200 l l l 7 2 Algodão Coloridos (3): brancos pouco sujos e cores delicadas. 3 Sintéticos: coloridos delicados muito sujos. 40° 1200 l l l 7 85 60° 800 - l l 3 85 3 Sintéticos delicados: coloridos resistentes pouco sujos. Mix 30': para refrescar rapidamente roupas levemente sujas (não é 4 indicado para lã, seda e roupas que deve ser lavadas à mão). Mix 15': para refrescar rapidamente roupas levemente sujas (não é 5 indicado para lã, seda e roupas que deve ser lavadas à mão). 40° 800 - l l 3 70 30° 800 - l l 3 30 30° 800 - l l 1,5 15 - 1200 - - l 7 36 Programas Parciais A Enxaguamento B Enxaguamento Delicado C Centrifugação D Centrifugação Delicada E Descarga - 800 - - l 3 31 - 1200 - - - 7 16 - 800 - - - 3 12 - 0 - - - 7 2 Os dados apresentados na tabela têm valor indicativo. Para todos Test Institutes: 1) Programa de controlo segundo a norma EN 60456: configurar o programa 6 com uma temperatura de 60ºC. 2) Programa longo para algodão: configurar o programa 1 com uma temperatura de 40ºC. 3) Programa curto para algodão: configurar o programa 2 com uma temperatura de 40ºC. Programas especiais Higienização (programa 6). Um programa higienizante com alta temperatura que prevê o uso de lixívia com temperaturas superiores aos 60ºC. Para branquear, deite a lixívia, os detergentes e os aditivos nos respectivos compartimentos (veja o parágrafo Gaveta dos detergentes). Ciclo Boa noite (programa 7). É um ciclo silencioso que pode trabalhar de noite, quando a tarifa energética é reduzida. O programa foi estudado para roupas sintéticas e de algodão. No fim do ciclo, a máquina irá parar com água no tambor; para efectuar a centrifugação e a descarga mete na tecla INÍCIO/PAUSA, caso contrário, depois de 8 horas a máquina efectuará automaticamente a centrifugação e a descarga da água. Ciclo Bébés (programa 8). Programa para remover a sujidade típica das roupas das crianças, garantindo a remoção do detergente para evitar alergias na pele delicada das crianças. O ciclo foi estudado para reduzir as bactérias utilizando uma maior quantidade de água e optimizando o efeito de aditivos específicos higienizantes, acrescentados ao detergente. No fim da lavagem, a máquina efectuará lentas rotações do tambor para evitar a formação de dobras; para terminar o ciclo, mete na tecla INÍCIO/PAUSA. Mix 30' (programa 4) foi estudado para lavar peças levemente sujas em pouco tempo: leva apenas 30 minutos e, desta maneira, economiza energia e tempo. Se regular o programa (4 a 30°C) será possível lavar juntos tecidos de natureza diferente (excepto lã e seda), com uma carga máxima de 3 Kg. Mix 15' (programa 5) foi estudado para lavar peças levemente sujas em pouco tempo: leva apenas 15 minutos e, desta maneira, economiza energia e tempo. Se regular o programa (5 a 30°C) será possível lavar juntos tecidos de natureza diferente (excepto lã e seda), com uma carga máxima de 1,5 Kg. 18 Personalizações Seleccione a temperatura Gire o selector da TEMPERATURA para seleccionar a temperatura de lavagem (veja a Tabela dos programas). A temperatura pode ser diminuída até a lavagem a frio ( ). A máquina impedirá automaticamente a configuração de uma temperatura superior à máxima prevista para cada um dos programas. Seleccione a centrifugação Gire o selector da CENTRIFUGAÇÃO para seleccionar a velocidade de centrifugação do programa seleccionado. As velocidades máximas que há para os programas são: Programas Velocidade máxima Algodão 1200 rotações por minuto Sintéticos 800 rotações por minuto Lã 600 rotações por minuto Seda somente descarga A velocidade de centrifugação pode ser diminuída, ou excluída se seleccionar o símbolo . A máquina impedirá automaticamente a realização de uma centrifugação superior à máxima de cada um dos programas. Funções As várias funções de lavagem da máquina de lavar roupa possibilitam obter-se a limpeza e o branco que desejar. Para activar as funções: 1. mete na tecla relativa à função desejada; 2. o respectivo indicador luminoso acende-se para avisar que a função está activada. Observação: Se um indicador luminoso acender-se intermitente, significa que a respectiva função não pode ser seleccionada para o programa definido. Início posterior Atrasa o início da máquina de até 12 horas. Mete várias vezes na tecla até acender-se o indicador luminoso correspondente ao atraso desejado. A quinta vez que carregar na tecla, a função se desactivará. Obs.: Depois de ter carregado na tecla INÍCIO/PAUSA, será possível mudar o valor do atraso somente para diminui-lo. É activo com todos os programas. Engomar fácil Seleccionando esta função, a lavagem e a centrifugação serão oportunamente modificadas para reduzir a formação de rugas. No fim do ciclo, a máquina de lavar roupa efectuará lentas rotações do tambor; o indicador luminoso da função ENGOMAR FÁCIL e aquele de INÍCIO/PAUSA ficarão intermitentes (laranja) e a fase permanecerá acesa fixa. Para terminar o ciclo, carregar no botão INÍCIO/PAUSA ou na tecla ENGOMAR FÁCIL. No programa Seda a máquina terminará o ciclo com a roupa de molho e o indicador luminoso da função ENGOMAR FÁCIL e aquele de INÍCIO/PAUSA ficarão intermitentes (laranja) e a fase ENXAGUAMENTO permanecerá acesa fixa. Para descarregar a água e poder retirar a roupa é necessário carregar na tecla INÍCIO/ PAUSA ou na tecla ENGOMAR FÁCIL. Não pode ser activada nos programas 4, 5, 6, 7, 8, 11, C, D, E. Enxaguamento extra Seleccionando esta função aumenta-se a eficácia da enxaguamento e garante-se a máxima remoção do detergente. É útil para quem tem a pele particularmente sensível. Não pode ser activada nos programas 4, 5, C, D, E. Super lavagem Graças ao uso de uma maior quantidade de água na fase inicial do ciclo e a uma maior duração, esta função garante uma lavagem de alto desempenho. Não pode ser activada nos programas 4, 5, 6, 10, 11, A, B, C, D, E. 19 PT Detergentes e roupa PT Gaveta dos detergentes O bom resultado da lavagem depende também do emprego da dose certa de detergente: com excessos não se lava de maneira mais eficaz, mas contribui-se para formar crostas nas peças internas da máquina de lavar roupa e poluir o meio ambiente. Não use detergentes para lavagem à mão, porque formam espuma demais. Tire a gaveta dos detergentes e deite o 3 detergente ou o aditivo da seguinte maneira: MAX 1 2 gaveta 1: Detergente para lavagem (em pó ou líquido) O detergente líquido deve ser deitado somente depois da máquina ter arrancado. gaveta 2: Aditivos (amaciador etc.) O aditivo amaciador não deve ultrapassar a grade. gaveta adicional 3: Água de Javel Ciclo para branquear O branqueamento pode ser efectuado somente com os programas 1, 2, 6. Deite a água de javel no recipiente adicional 3, o detergente e o produto amaciador nos respectivos recipientes, em seguida programar um dos programas acima indicados. É indicado apenas para roupas de algodão muito sujas. Preparar a roupa Divida a roupa em função: - do tipo de tecido / do símbolo na etiqueta. - das cores: separe as peças coloridas das brancas. Esvazie as algibeiras e verifique se há botões soltos. Não ultrapasse os valores indicados que se referem ao peso da roupa enxuta: Tecidos resistentes: máx. 7 kg. Tecidos sintéticos: máx. 3 kg. Tecidos delicados: máx. 2 kg. Lã: máx. 1,5 kg. 20 Quanto pesa a roupa? 1 1 1 1 1 lençol 400 - 500 g. fronha 150 - 200 g. toalha de mesa 400 - 500 g. roupão 900 - 1200 g. toalha de rosto 150 - 250 g. Peças especiais Camisas: Utilize o programa específico 9 para lavar camisas de vários tipos de tecido e cores. Garante a máxima limpeza minimizando a formação de dobras. Seda: utilize o programa específico 10 para lavar todas as roupas de seda. Aconselha-se o uso de um detergente específico para tecidos delicados. Cortinas: dobre-as bem e coloque-as dentro de uma fronha ou de um saquinho de rede. Utilize o programa 10. Lã: a Hotpoint/Ariston é a única máquina de lavar roupa que obteve o prestigioso reconhecimento Woolmark Platinum Care (M0508) por parte da The Woolmark Company, que certifica a lavagem à máquina de todas as roupas de lã, mesmo daquelas . Com o com etiqueta lavar somente à mão programa 11 teremos portanto a absoluta tranquilidade de lavar à máquina todas as peças de lã (max. 1,5 kg) com a garantia das melhores performances. Sistema de balanceamento da carga Antes de cada centrigfugação, para evitar vibrações excessivas e para distribuir a carga em modo uniforme, o tambor efectua algumas rotações a uma velocidade levemente superior àquela de lavagem. Se no fim de repetidas tentativas a carga ainda não estiver correctamente balanceada, a máquina efectuará a centrifugação com uma velocidade inferior àquela prevista. No caso de um excessivo desbalanceamento, a máquina de lavar roupa efectuará a distribuição ao invés da centrifugação. Para favorecer uma melhor distribuição da carga e o seu correcto balanceamento, aconselha-se misturar peças grandes com peças pequenas. Precauções e conselhos Esta máquina de lavar roupa foi projectada e fabricada em conformidade com os regulamentos internacionais de segurança. Estas advertências são fornecidas por razões de segurança e devem ser lidas com atenção. Abertura manual da porta de vidro Caso não seja possível abrir a porta de vidro por falta de energia eléctrica e quiser pendurar a roupa lavada, proceda da seguinte maneira: Segurança geral Este aparelho foi projectado exclusivamente para um uso doméstico. Esta máquina de lavar roupa deve ser utilizada somente por pessoas adultas e conforme as instruções apresentadas neste manual. Não toque na máquina com os pés descalços nem com as mãos ou os pés molhados ou húmidos. Não puxe o cabo eléctrico para tirar a ficha da tomada, pegue a ficha mesmo. Não abra a gaveta dos detergentes enquanto a máquina estiver a funcionar. Não toque a água de descarga, que poderá chegar a temperaturas altas. Em nenhum caso force a porta para abri-la: poderá danificar o mecanismo de segurança que a protege contra aberturas acidentais. 20 1. tire a ficha da tomada de corrente. 2. verifique que o nível de água no interior da máquina seja inferior respeito à abertura da porta de vidro; caso contrário, tirar a água em excesso através do tubo de descarga recolhendo-a num balde como indicado na figura. 3. tire o painel de cobertura da parte dianteira da máquina de lavar roupa com ajuda de uma chave de fendas(veja a figura). Se houver avarias, em nenhum caso mexa nos mecanismos internos para tentar reparar. Verifique sempre que criança não se aproximem da máquina a funcionar. Durante a lavagem a porta de vidro tende a aquecer-se. Se for preciso deslocá-la, são precisas pelo menos duas ou três pessoas, com a máxima atenção. Nunca sozinho porque a máquina é muito pesada. Antes de colocar a roupa verifique que o tambor esteja vazio. Eliminação Eliminação do material de embalagem: obedeça os regulamentos locais, de maneira que as embalagens possam ser reutilizadas. A directiva Europeia 2002/96/CE referente à gestão de resíduos de aparelhos eléctricos e electrónicos, prevê que os electrodomésticos não devem ser escoados no fluxo normal dos resíduos sólidos urbanos. Os aparelhos desactualizados devem ser recolhidos separadamente para optimizar a taxa de recuperação e reciclagem dos materiais que os compõem e impedir potenciais danos para a saúde humana e para o ambiente. O símbolo constituído por um contentor de lixo barrado com uma cruz deve ser colocado em todos os produtos por forma a recordar a obrigatoriedade de recolha separada. Os consumidores devem contactar as autoridades locais ou os pontos de venda para solicitar informação referente ao local apropriado onde devem depositar os electrodomésticos velhos. 4. utilizando a lingueta indicada na figura, puxe para o exterior até liberar o tirante de plástico do fecho; puxá-lo sucessivamente para baixo e contemporaneamente abrir a porta. 5. monte outra vez o painel, certifique-se, antes de empurrá-la na máquina, que os ganchos foram colocados nas respectivas ranhuras. 21 PT Manutenção e cuidados PT Interromper a alimentação de água e de corrente eléctrica Feche a torneira da água depois de cada lavagem. Desta maneira diminuiu-se o desgaste do sistema hidráulico da máquina de lavar roupa e elimina-se o risco de inundação. Limpar a bomba Esta máquina de lavar roupa é equipada com uma bomba com limpeza automática que não precisa de operações de manutenção. Entretanto pode acontecer que pequenos objectos (moedinhas, botões) caiam na pré-câmara que protege a bomba, situada na parte inferior da mesma. Tire a ficha da tomada eléctrica quando for limpar a máquina de lavar roupa e durante os trabalhos de manutenção. Certifique-se que o ciclo de lavagem tenha terminado e tire a ficha da tomada. Limpar a máquina de lavar roupa Para obter acesso à pré-câmara: A parte externa e as peças em borracha podem ser limpas com um pano molhado com água morna e sabão. Não empregue solventes nem abrasivos. Limpar a gaveta dos detergentes Para tirar a gaveta, erga-a e puxe-a para fora (veja a figura). Lave-a com água corrente; esta limpeza deve ser efectuada frequentemente. 1 2 1. tire o painel de cobertura da parte dianteira da máquina de lavar roupa com ajuda de uma chave de fendas (veja a figura); 2. desenrosque a tampa girando-a no sentido anti-horário (veja a figura). é normal que perca um pouco de água; Cuidados com a porta de vidro e o tambor Deixe a porta sempre entreaberta para evitar que se formem odores desagradáveis. 3. limpe o interior com cuidado; 4. enrosque outra vez a tampa; 5. monte outra vez o painel, certifique-se, antes de empurrá-la na máquina, que os ganchos foram colocados nas respectivas ranhuras. Verificar o tubo de alimentação de água Verifique o tubo de alimentação pelo menos uma vez por ano. Se houver rachaduras ou fendas, será necessário substitui-lo: durante as lavagens as fortes pressões podem provocar repentinas quebras. Nunca utilize tubos já usados. 22 Anomalias e soluções Pode acontecer que a máquina de lavar roupa não funcione. Antes de telefonar para a Assistência Técnica (veja Assistência), verifique se não se trata de um problema fácil de resolver com ajuda da seguinte lista. PT Anomalias: Possíveis causas / Solução: A máquina de lavar roupa não liga. A ficha não está colocada na tomada eléctrica, ou não o suficiente para haver contacto. Em casa não há corrente. O ciclo de lavagem não inicia. A porta de vidro não está bem fechada. O botão LIGA/DESLIGA não foi pressionado. O botão INÍCIO/PAUSA não foi pressionado. A torneira da água não está aberta. Foi programado um início posterior (veja as Personalizações). A máquina de lavar roupa não carrega a água (o indicador luminoso da primeira fase de lavagem pisca rapidamente). O tubo de alimentação de água não está ligado na torneira. O tubo está dobrado. A torneira da água não está aberta. Está a faltar água em casa. Não há suficiente pressão. O botão INÍCIO/PAUSA não foi pressionado. A máquina de lavar roupa carrega e descarrega água continuamente. O tubo de descarga não está instalado entre 65 e 100 cm de altura do chão (veja Instalação). A ponta do tubo de descarga está imersa na água (veja Instalação). Da descarga na parede não foi sangrado o ar. Se depois destas verificações o problema não for resolvido, feche a torneira da água, desligue a máquina de lavar roupa e chame a assistência técnica. Se a morada encontrar-se nos últimos andares de um edifício, é possível que aconteçam fenómenos de sifão por causa dos quais a máquina de lavar roupa carrega e descarrega água continuamente. Para eliminar este inconveniente, há a disposição no comércio apropriadas válvulas contra o efeito sifão. A máquina de lavar roupa não descarrega ou nem realiza centrifugação. No programa não há descarga: com alguns programas será necessário iniciar a descarga manualmente. Está activa a função ENGOMAR FÁCIL: para completar o programa mete na tecla INÍCIO/PAUSA (veja as Personalizações). O tubo de descarga está dobrado (veja Instalação). A conduta de descarga está entupida. A máquina de lavar roupa vibra muito durante a centrifugação. O tambor, no momento da instalação, não foi liberado correctamente (veja Instalação). A máquina não está nivelada (veja Instalação). A máquina está apertada entre móveis e parede (veja Instalação). Da máquina de lavar roupa está a perder água. O tubo de alimentação da água não está bem enroscado (veja Instalação). O gaveta dos detergentes está entupida (para limpá-la veja Manutenção e cuidados). O tubo de descarga não está fixado correctamente (veja Instalação). O indicador luminoso INÍCIO/ PAUSA (laranja) e os indicadores das funções piscam rapidamente. Desligue a máquina e tire a ficha da tomada, aguarde aproximadamente 1 minuto e volte a ligá-la. Se a anomalia persistir, contacte a Assistência Técnica. Está a formar-se demasiada espuma. O detergente não é específico para máquina de lavar roupa (deve haver a escrita para máquina de lavar, à mão e para máquina de lavar ou similares). A dose foi excessiva. 23 Assistência 195068705.00 01/2008 - Xerox Business Services Antes de contactar a Assistência Técnica: Verifique se consegue resolver a anomalia sozinho (veja Anomalias e soluções); Reinicie o programa para verificar se o inconveniente foi resolvido; Em caso negativo, contacte a o Centro de Assistência técnica autorizada no número de telefone indicado no certificado de garantia. PT Nunca recorra a técnicos não autorizados. Comunique: o tipo de anomalia; o modelo da máquina (Mod.); o número de série (S/N). Estas informações encontram-se na placa colocada na parte traseira da máquina de lavar roupa e na parte anterior abrindo a porta de vidro. 24
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project