KitchenAid | KCBPZ 18120.1 | Setup and user guide | KitchenAid KCBPZ 18120.1 Setup and user guide

Product sheet
Quick Guide
Carefully read the user handbook provided before using the appliance.
Freezer Compartment
I. Control panel
2. LED’s lighting
3. Ice tray
4. Shock Freeze compartment
5. Drawer divider
6. Bottle rack
7. Glass shelves
8. Rating plate with commercial name
9. Area for freezing fresh food or to store
frozen food
10. Area for storing frozen foods
11. Door seal
1
2
9
3
4
5
6
7
10
Note: All shelves, drawers and flaps are removable.
The ideal food storage temperatures are already
factory-set.
8
The characteristics, technical data and images
may vary according to the model.
11
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, it starts
the operation automatically. After starting the
appliance, wait at least 4-6 hours before placing
food into the appliance.
When the appliance is connected to the power
supply, the display lights up and all the icons appear
on the display for approximately 1 second. The
default (factory) values of the fridge compartment
settings light-up.
3
Control panel
Control panel
SHOCK FREEZE button
On/Stand-by
To put the product in Stand-by, press and hold
the button for 3 seconds.
All the icons turn off except On/Standby indicator.
To reactivate the appliance press once (briefly)
this button.
Note: this operation does not disconnect the
appliance from the power supply.
Shock Freeze function
Press to activate/deactivate the Shock Freeze
function (see the Instructions for Use). The
function switches off automatically after about 4-5
hours. Shock Freeze and Fast Freezing functions
can’t be both active at the same time.
OPT TARIFF (NIGHT TIME RATE) button
Press to activate/deactivate the Opt Tariff
function. The Opt Tariff function enables
appliance energy consumption to be
concentrated in the reduced rate hours, generally
at night (see the Instructions for Use).
Temperature display
The display can show either the temperature in
the freezer compartment (between -16°C and 24°C).
Stop Alarm
Press in case of alarm to mute the acoustic alarm
.
ProFreeze technology
ProFreeze technology automatically works to
ensure the optimal conditions to preserve the
stored food.
Freezer compartment temperature
A different temperature can be set using the
“Temperature” button. The storage temperature
can be changed by -1°C with each pressure of the
button: the value changes cyclically between 16°C and -24°C.
Fast Freeze
Long-press the “Freezer” button for 3 seconds 24
hours before placing large amounts of food in the
freezer compartment. When the function is
activated, the symbol
lights up.
This function is automatically deactivated after 50
hours. To speed up freezing times, the bottom
drawer can be removed and food placed directly
on the bottom of the compartment.
Shock Freeze and Fast Freeze functions can’t be
both active at the same time.
Note: food to be frozen must not be touching
already frozen food.
4
What to do if…
Possible causes
Solutions
The control panel is
switched off, the
appliance does not
work.
The appliance could be in
On/Standby mode.
There may be a problem with the
power supply to the appliance.
Activate the appliance with the
On/Standby button. Make sure:
- there is no power cut
- the plug is properly inserted in the
socket and that any double-pole mains
switch is in the correct position (i.e.
allowing the appliance to be powered)
- the household electrical system
protection devices are in good
working order
- the power supply cable is not
damaged.
The inside light does
not work.
The light may need replacing.
Models with LED lights: contact the
authorised Service Centre.
The appliance could be in
On/Standby mode.
Activate the appliance with the
On/Standby button.
The temperature
inside the
compartments is not
low enough.
There could be various causes (see
“Solutions”).
Make sure:
- the doors close properly
- the appliance is not installed near a
heat source
- the set temperature is adequate
- the air circulation through the vents
at the bottom of the appliance is not
obstructed.
The Black Out Alarm
icon remains on, the
Alarm indicator blinks
and the Temperature
display (°C) blinks,
showing the
maximum
temperature reached
during blackout.
Prolonged power failure, able to
cause the inside temperature to
increase to 0°C.
Press the Stop Alarm button the
acoustical alarm stops, the
Temperature Display (°C) blinks and
the Alarm Indicator remains on until a
temperature < -10°C is reached.
The front edge of the
appliance, at the door
striker seal, is hot.
This is not a defect. It prevents
condensation.
No solution is necessary.
5
What to do if…
Possible causes
Solutions
The red led
flashes
and an acoustic signal
sounds.
Door open alarm
Activates when the freezer
compartment door has remained
open for more than 2 minutes.
Close the door or press the Stop Alarm
to mute the acoustical alarm.
The red led
flashes,
an acoustic signal
sounds and the
symbol
is
displayed.
Blackout alarm
Activates when a prolonged power
cut causes the freezer
compartment temperature to rise.
Note: a different product
temperature cannot be set until
the blackout alarm is deactivated.
Before deactivating the acoustic signal,
it is advisable to pay attention to the
temperature shown on the
temperature display, corresponding to
the highest temperature reached in
the freezer compartment during the
power failure. Press the “Stop Alarm”
button briefly to deactivate the
acoustic signal. After pressing the
button, the temperature display shows
the set temperatures again. If the
freezer compartment has not yet
reached the optimum food storage
temperature, the freezer compartment
temperature alarm could be activated
(see freezer compartment temperature
alarm). Check the food before
consuming it.
The red led
lights
up (without flashing),
an acoustic signal
sounds and the
freezer compartment
temperature display
flashes.
Freezer compartment
temperature alarm
The freezer compartment
temperature alarm indicates that
the temperature is not at the
optimum level. This may happen:
with first use, after defrosting
and/or cleaning, if large amounts
of food are placed inside the
freezer or when the freezer door
has not been closed properly.
To deactivate the acoustic signal, press
the Stop Alarm button ; the acoustical
alarm stops, the Temperature Display
(°C) blinks and the Alarm Indicator
remains on until a temperature < -10°C
is reached.
The red led
lights
up, an acoustic signal
sounds and the letter
“F” flashes on the
display.
Malfunction Alarm
The alarm indicates a fault in a
technical component.
Call the authorised Service Centre.
Press the “Stop Alarm” button briefly
to deactivate the acoustic signal.
Note: it is normal for the refrigeration system to produce some noises, such as gurgling and hissing.
6
n
Printed in Italy
05/16
19514595400
GB
Download PDF

advertising