Whirlpool ADP 81 AS SL Instruction for Use
Add to my manuals4 Pages
Whirlpool ADP 81 AS SL is a dishwasher with a variety of features to make dishwashing easier and more efficient. It includes a Half Load option that allows you to wash either the upper or lower rack only, saving time and energy. The Power Clean option provides increased pressure and water coverage in the lower rack for heavily soiled items. You can also delay the start of a wash cycle by up to 24 hours using the Delayed Start feature. Additionally, the dishwasher has indicators to let you know when to add rinse aid and regeneration salt, ensuring optimal performance.
advertisement
▼
Scroll to page 2
of 4
How to use the appliance Further indications are given in the single chapters and in the user instructions. Switch on the appliance Select, save, and supply the detergent Check the rinse aid level Check the regeneration salt level Load the racks Press the ON / OFF button. (The first time you use the appliance and when using a different type of detergent) A BC 1. Select the third programme from the top in the relative table. 2. Press the Start button for about 7 seconds until the display changes. 3. Select the required detergent with the Start button (OFF = powder detergent, 2 in 1, 3 in 1, 4 in 1) (shown on the display). 4. Switch the appliance off and then switch it on again. The selected detergent type will be shown on the display for approximately 3 seconds after switching on. For dosage of powder detergent in compartment A and B refer to the programmes table. Mechanical indicator C. Electric indicator on control panel (if provided). On models with water softener system only. Mechanical indicator D. Electric indicator on control panel (if provided). Refer to the dishwasher loading instructions. Close the dishwasher door, turn on the water tap Select a programme Select additional options The last programme selected will light up. Select the desired programme (using the specific button or knob). The corresponding indicator lamp lights up. If necessary (and if provided). The corresponding indicator lamp lights up. “Change programme in progress” Wash cycle Press the Start button Switch off the appliance Turn off the water tap, unload the racks The selected programme is then memorised (even in the event of power failure). Press the START button for 2 sec. until the Start indicator lamp switches off. Select another programme and press the START button again. - Only open the dishwasher if necessary (Warning: beware of hot steam). - If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted. Only after the START button has switched off: Press the ON / OFF button. All the indicator lamps switch off. Warning: When the door is opened steam comes out! Unload the appliance, starting from the lower rack. Dishwasher loading instructions and racks provided depending on the model B Upper rack: Crockery holder (A): Depending on the position, for long-handles utensils, cups and plates. Glass holder (B): Long-stemmed glasses. Long-handled utensils (e.g. carving forks, knives) must be arranged with the sharp end facing in towards the appliance. A Half Load: Load the upper rack (see description of Options). Place the cutlery basket (C), if provided, in the upper rack. Rack height adjustment (also when loaded): Pull the two rack handles (D) Lower adjustment: outwards and lower the rack. Pull the two rack handles (D) upwards until the rack clicks Upper adjustment: into place (factory setting). C The rack must be level on both sides. D D Retainer open Removing the top rack to provide clearance for large items of crockery in the bottom rack: Open the rack guide retainers (E) on the right and left and remove the top rack. When the upper rack is in place the retainers must always be closed. Retainer closed E E Lower rack: Depending on the model with fixed, tilting (F) or tilting split plate holders (G). Half Load: Load the lower rack (see description of Options). Greater washing power, particularly for plates and saucepans. F F H Power Clean load Increased wash power in the dedicated area (H) and high flexibility for lower rack loading. G Cutlery basket (I): J Grid (J) to keep items separate. Sharp knives and forks that might cause injury must be placed in the cutlery basket with the sharp end facing downwards. I C Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a dishwasher, for example wooden items, aluminium, tin, hand-decorated crockery (unglazed), silver cutlery. What to do if... If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see also the corresponding chapter in the user instructions). Problem The appliance is not working If crockery is not perfectly dry If crockery is not perfectly clean Cause Remedy • No water supply. • Open the tap. • The appliance does not load sufficient water. • Clean the water supply tap filter. • Ensure there are no kinks in the water hose. • There is a power failure. • • • • • Starting the selected programme. • The programme can be set to “0” to start. • Insufficient rinse aid. • Increase dosage *. • Residual water in cavities. • Load crockery at an angle. • The water jet does not reach the crockery. • Arrange crockery so that items do not touch each other. Load crockery upside down. • Insufficient detergent. • Follow recommended detergent dosage. • Unsuitable programme. • Select a more intense wash cycle. • Spray arms blocked. • The spray arms must be able to turn freely. • Spray arm nozzles clogged. • Remove any impurities obstructing the water flow *. Insert the plug into the mains socket. Press the Start button. Close the door. Check the safety circuit breaker. • Incorrect detergent/detergent too old. • Use a good quality detergent. Sandy or grainy residues Colour of plastic parts faded • Clogged filters. • Check filters regularly/if necessary clean *. • Filters incorrectly assembled. • Insert the filter correctly *. • Tomato/carrot juice, ... • Depending on the material, if necessary use a detergent with a greater whitening power. • Streaks on the crockery/glasses. • Increase the rinse aid dosage *. • Streaks on glasses. • Reduce the rinse aid dosage *. • Layer of salt on crockery/glasses. • Close the salt container lid properly *. • Insufficient water softening, calcium deposits. • Change water hardness setting, if necessary add salt *. Deposits on crockery • Removable • Not removable Opaque glasses/ glasses • Cannot be washed in the dishwasher. not sparkling • Use suitable glasses. Rust on cutlery • Not made of stainless steel. • Use suitable cutlery. Identifying appliance faults • The START indicator lamp flashes. • Indicator F... (if provided). • Ensure the filter assembly is not clogged and that there is no interruption to the water supply (if necessary, clean the filters *). Start the programme again. Press the START button for 2 seconds, until the START indicator lamp switches off. Select a new programme and press the Start button again. If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water supply tap, then call our After-Sales Service (see guarantee). Before contacting our After-Sales Service, take note of the following: • The nature of the fault • The appliance type and model • The service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side. Before using the dishwasher, read the user instructions! GB Quick Reference Guide ADP 81 AS Wash cycle Programme selection button Pre-Rinse Washing Options On / Off button Drying 3) Power Clean 4) An increased pressure combined with additional spray level offers better cleaning result and more flexibility of dish loading in the lower rack. Start button Time and failure display Switches “on” when the dishwasher is operating. Flashes when a fault occurs. Switches off at the end of the programme. Indicates in hours the time remaining until the start of the wash cycle. Switches off when the programme starts and indicates the time remaining in hours and minutes. “F....” Identification of faults for service technician Indicators “Delayed start” button The wash cycle can be programmed to start after 1 - 24 hours. With each successive touch of the button, the delayed start indicator increases by 1 hour, and after 24 returns to 00. Then press the Start button. The dishwasher will start at the set time. Add rinse aid Add regeneration salt Only add regeneration salt immediately before starting a wash programme. “Half load - Multizone” button Load the upper or lower rack only. This function can be used with any programme. Press once = upper rack (the indication lamp/symbol comes on) Press twice = lower rack (the indication lamp/symbol comes on) Press 3 times = Off (half load function deactivated). When washing without the top rack, press the “Half Load” button twice, or “Lower rack wash” (the corresponding LED/symbol comes on). Detergent light No light = detergent in powder or The symbol lights up = tablets 2 in 1 or The symbol lights up = tablets 3 in 1.... X in 1 (For adjustment refer to “How to use the appliance”) Programme chart Programmes Consumption 3) Loading instructions A B Litres AquaSteam 4) 40-70°C Lightly, normally or heavily soiled crockery, including pots and pans. X X 7-17 Pre-Rinse cold Crockery to be washed later. - - 4.0 0.03 14 Party Glass 40°C Light soiling, for example glasses and cups. X - 10.0 0.85 100 Rapid 30 min 40°C Lightly soiled crockery with no dried-on food. X - 10.0 0.65 30 Bio 1) 4) 50°C Normally soiled crockery. X X 13.0 1.05 170 55°C Normally soiled crockery, gentle and quiet programme thanks to the low spray pressure (39dbA). X X 13.0 1.20 290 Overnight 1) 2) Detergent 2) Reference programme for energy label EN 50242. Refer to “User instructions”. 3) kWh Minutes 0.99-1.75 65-220 The data relevant to programmes are values obtained in the laboratory in conformity with Standard EN 50242. In practice there may be time variations or leaps depending on different loads, function options, sensor calibration (only for sensorcontrolled programmes) water temperatures or hardness and different power supply voltages. These programmes can be used with the “Power Clean” option. 4) Important information for Test Laboratories: For detailed information on the EN comparison test and other tests, contact the following address: “[email protected]”. Whirlpool is a registered trademark of Whirlpool USA 5019 396 01619 (We reserve the right to make technical modifications)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
Frequently Answers and Questions
What should I do if the dishes are not drying properly?
There might be insufficient rinse aid. Increase the dosage by following the instructions in the user manual.
How do I use the half-load function?
To use the half-load function, press the "Half load - Multizone" button either once for the upper rack or twice for the lower rack. The corresponding indicator lamp will light up.
What is the "Power Clean" option and how do I use it?
The "Power Clean" option provides better cleaning results and more flexibility for loading dishes in the lower rack. It combines increased pressure with an additional spray level. To use it, press the "Power Clean" button before starting a wash cycle.
What should I do if the dishes are not clean after a wash cycle?
There might be insufficient detergent. Follow the recommended dosage instructions provided in the user manual.
What is the "Delayed start" function and how do I use it?
The "Delayed start" function allows you to program the wash cycle to start after a delay of 1 to 24 hours. Press the "Delayed start" button repeatedly until the desired delay time is set, then press the "Start" button.