KitchenAid | KOLCP 60600 | Instruction for Use | KitchenAid KOLSP 60600 Instruction for Use

Instructions for use
Important safety instructions
4
Installation
8
Safeguarding the environment
9
EC Declaration of conformity
9
Troubleshooting Guide
9
After-Sales Service
10
Cleaning
10
Maintenance
11
Instructions for oven use
13
Functions description table
26
Cooking table
28
Table of Tested Recipes
31
Recommended use and tips
32
These instructions are also available on the website: www.kitchenaid.eu
Important safety instructions
YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT
This manual and the appliance itself provide important safety warnings, to be
read and observed at all times.
This is the danger symbol, pertaining to safety, which alerts users to
potential risks to themselves and others. All safety warnings are
preceded by the danger symbol and the following terms:
DANGER
Indicates a hazardous situation which,
if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which,
if not avoided, could cause serious injury.
All safety warnings give specific details of the potential
risk present and indicate how to reduce risk of injury,
damage and electric shock resulting from improper use
of the appliance. Carefully observe the following
instructions:
•Use protective gloves to perform all unpacking and
installation operations.
•The appliance must be disconnected from the power
supply before carrying out any installation work.
•Installation and maintenance must be carried out by a
qualified technician, in compliance with the
manufacturer’s instructions and local safety
regulations. Do not repair or replace any part of the
appliance unless specifically stated in the user manual.
•Power cable replacement must be carried out by a
qualified electrician. Contact an authorised service
centre.
•Regulations require that the appliance is earthed.
•Once the appliance is fitted in its housing, the power
4
cable must be long enough to connect the appliance to
the main power supply.
•For installation to comply with current safety
regulations, an all-pole disconnect switch with
minimum contact gap of 3 mm must be used.
•Do not use multiple plug adaptors if the oven is fitted
with a plug.
•Do not use extension leads.
•Do not pull the power supply cable.
•The electrical components must not be accessible to
the user after installation.
•If the surface of the induction plate is cracked, do not
use it and switch off the appliance to avoid the
possibility of electric shock (only for models with
induction function).
•Do not touch the appliance with any wet part of the
body and do not operate it when barefoot.
•This appliance is designed solely for use as a domestic
appliance for cooking food. No other type of use is
permitted (e.g.: heating rooms).
The manufacturer declines all responsibility for
inappropriate use or incorrect setting of the controls.
•The appliance and its accessible parts become hot
during use.
•Care should be taken to avoid touching heating
elements.
•Very young (0-3 years) and young children (3-8 years)
shall be kept away unless continuously supervised.
•Children of 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack
of experience and knowledge, can use this appliance
5
only if they are supervised or have been given
instructions on safe appliance use and understand the
hazards involved. Children must not play with the
appliance. Cleaning and user maintenance must not be
performed by children without supervision.
•During and after use, do not touch the heating
elements or interior surfaces of the appliance – risk of
burns. Do not allow the appliance to come into
contact with cloths or other flammable materials until
all the components have cooled down completely.
•At the end of cooking, exercise caution when opening
the appliance door, letting the hot air or steam exit
gradually before accessing the oven. When the
appliance door is shut, hot air is vented from the
aperture above the control panel. Do not obstruct the
vent apertures.
•Use oven gloves to remove pans and accessories,
taking care not to touch the heating elements.
•Do not place flammable materials in or near the
appliance: a fire may break out if the appliance is
inadvertently switched on.
•Do not heat or cook sealed jars or containers in the
appliance.
•The pressure that builds up inside might cause the jar
to explode, damaging the appliance.
•Do not use containers made of synthetic materials.
•Overheated oils and fats catch fire easily. Always
remain vigilant when cooking foods rich in fat and oil.
•Never leave the appliance unattended during food
drying.
•If alcoholic beverages are used when cooking foods
6
(e.g. rum, cognac, wine), remember that alcohol
evaporates at high temperatures. As a result, there is a
risk that vapours released by the alcohol may catch
fire upon coming into contact with the electrical
heating element.
•Never use steam cleaning equipment.
•Do not touch the oven during the pyrolysis cycle.
Keep children away from the oven during the pyrolysis
cycle. Any excess spillage must be removed from the
oven cavity before the cleaning cycle (only for ovens
with Pyrolysis function).
•During and after the pyrolysis cycle, the animals have
to be kept away from the area of the appliance
location (only for ovens with Pyrolysis function).
•Use only the temperature probe recommended for
this oven.
•Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass as they can scratch
the surface, which may result in the glass shattering.
•Ensure that the appliance is switched off before replacing
the lamp to avoid the possibility of electric shock.
•Do not use aluminium foil to cover food in the cooking
vessel (only for ovens with a cooking vessel supplied).
SCRAPPING OF HOUSEHOLD APPLIANCES
• This appliance is manufactured with recyclable or reusable materials. Scrap
the appliance in accordance with local regulations on waste disposal. Before
scrapping, cut off the power cords so that the appliances cannot be
connected to the mains.
• For further information on the treatment, recovery and recycling of
household electrical appliances, contact your competent local authority, the
collection service for household waste or the store where you purchased the
appliance.
7
Installation
After unpacking the oven, make sure that it has not
been damaged during transit and that the oven
door closes properly.
In the event of problems, contact the dealer or
your nearest After-Sales Service. To avoid any
damage, only remove the oven from its
polystyrene foam base at the time of installation.
1. To lower the power absorption setting, turn the
"Functions" knob to "SETTINGS" and select.
2. Confirm with button
3. Select "power" on the menu
4. Confirm with button
5. Select "LOW"
6. Press button
; a message appears on the
display confirming your selection.
Preparing the housing unit
• Kitchen units in contact with the oven must be
heat resistant (min 90°C).
• Carry out all cabinet cutting work before fitting
the oven in the housing and carefully remove all
wood chips and sawdust.
• After installation, the bottom of the oven must
no longer be accessible.
• For correct appliance operation, do not
obstruct the minimum gap between the
worktop and the upper edge of the oven.
Cleaning
Settings
Traditional
Appliance and display settings
Language
Power
Time
Electrical connection
Make sure the power voltage specified on the
appliance dataplate is the same as the mains
voltage. The dataplate is on the front edge of the
oven (visible when the door is open).
• Power cable replacement (type H05 RR-F 3 x
1.5 mm2) must be carried out by a qualified
electrician. Contact an authorized service
centre.
The oven is programmed to operate with power
absorption above 2.5 kW (indicated by "HIGH" in the
settings, as shown in the figure below) which is
compatible with a domestic power supply above 3
kW. If the household has a lower power supply, the
setting must be lowered ("LOW" in the settings). The
table below details the recommended electrical
power settings for the various countries.
COUNTRY
ELECTRICAL POWER
SETTING
GERMANY
HIGH
SPAIN
LOW
FINLAND
HIGH
FRANCE
HIGH
ITALY
LOW
HOLLAND
HIGH
NORWAY
HIGH
SWEDEN
HIGH
U.K.
LOW
BELGIUM
HIGH
Appliance and display settings
High
Low
Over 2.5 kW
GENERAL RECOMMENDATIONS
Before use:
• Remove cardboard protection pieces,
protective film and adhesive labels from the
oven and the accessories.
• Remove the accessories from the oven and heat
it at 200°C for about an hour to eliminate the
smell and fumes from the protective grease and
insulating materials.
During use:
• Do not place heavy objects on the door as they
could damage it.
• Do not cling to the door or hang anything from
the handle.
• Do not cover the inside of the oven with
aluminium foil.
• Do not pour water into the inside of a hot oven;
this could damage the enamel coating.
• Do not drag pots or pans across the bottom of
the oven as this could damage the enamel
coating.
• Make sure that the electrical cables of other
appliances do not touch hot parts of the oven
or become trapped in the door.
• Do not expose the oven to atmospheric agents.
8
Safeguarding the environment
Disposal of packing materials
• The packaging materials are 100% recyclable
and are marked with the recycling symbol
(
).
• The various parts of the packing must therefore
be disposed of responsibly and in full
compliance with local authority regulations
governing waste disposal.
• The symbol
on the product or on the
accompanying documentation indicates that it
should not be treated as domestic waste but
must be taken to an appropriate collection
centre for the recycling of electrical and
electronic equipment.
Energy saving tips
• Only preheat the oven if specified in the
cooking table or your recipe.
• Use dark lacquered or enamelled baking moulds
as they absorb heat far better.
Appliance scrapping
• This appliance is marked according to the
European Directive 2012/19/EU, Waste
Electrical and Electronic Equipment (WEEE).
• By ensuring correct disposal of the product, the
user can help prevent potential negative
consequences for the environment and human
health.
EC Declaration of conformity
• This oven, which is intended to come into contact with foodstuffs, complies with European Regulation
(
) n.1935/2004 and has been designed, manufactured and sold in conformity with the safety
requirements of the "Low Voltage" directive 2006/95/CE (which replaces 73/23/CEE and subsequent
amendments) and the protection requirements of "EMC" directive "EMC" 2004/108/CE.
• This Appliance meets the eco design requirements of European regulations n. 65/2014, and n. 66/2014
in conformity to the European standard EN 60350-1
Troubleshooting Guide
The oven does not work:
• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
• Switch the oven off and then on again to see if the fault has been eliminated.
The electronic programmer does not work:
• If the display shows the letter " F " followed by a number, contact your nearest After-Sales Service.
Specify in this case the number after the letter " F ".
9
After-Sales Service
Before contacting the After-Sales Service:
1. See if you can solve the problem yourself with
the help of the suggestions given in the
"Troubleshooting guide".
2. Switch the appliance off and then on again it to
see if the problem has been eliminated.
• your full address;
• your telephone number.
If the fault persists after the above checks,
contact the nearest After-Sales Service.
If any repairs are required, contact an authorized
Service Centre (to guarantee the use of original
spare parts and correct repair).
Always specify:
• a brief description of the fault;
• the type and exact model of the oven;
• the service number (number after the word
Service on the rating plate), located on the right
hand edge of the oven cavity (visible when the
oven door is open). The service number is also
indicated on the guarantee booklet;
Cleaning
WARNING
- Do not use steam cleaners.
- Only clean the oven when it is cool to the
touch.
- Disconnect the appliance from the mains
power supply.
N.B: during prolonged cooking of foods with a
high water content (e.g. pizza, vegetables,
etc.) condensation may form
on the inside of the door and around the seal.
When the oven is cold, dry the inside of the
door with a cloth or sponge.
Oven exterior
IMPORTANT: do not use corrosive or abrasive
detergents. If any of these products
unintentionally comes into contact with the
appliance, clean immediately with a damp
microfibre cloth.
• Clean the surfaces with a damp microfibre cloth.
If it is very dirty, add a few drops of washing up
detergent to the water. Finish off with a dry
cloth.
Accessories:
• Soak the accessories in water with washing up
detergent immediately after use, handling them
with oven gloves if still hot.
• Food residues can be easily removed using a
washing-up brush or sponge.
Cleaning cycle of ovens with pyrolysis function
(if present):
WARNING
Oven interior
IMPORTANT: do not use abrasive sponges or
metallic scrapers or scourers. Over time, these
can ruin enamelled surfaces and the oven door
glass.
• After every use, allow the oven to cool then
clean it preferably while it is still warm in order
to remove built-up dirt and stains caused by food
residues (e.g. food with a high sugar content).
• Do not use corrosive or abrasive detergents.
• Clean the door glass with a suitable liquid
detergent. The oven door can be removed to
facilitate cleaning (see MAINTENANCE).
- Do not touch the oven during the pyrolysis
cycle.
- Keep children away from the oven during
the pyrolysis cycle
- Keep animals away during and after the
pyrolysis cycle.
This function burns off spatters produced inside the
oven during cooking at a temperature of approx.
500°C. At this high temperature, the deposits turn
into a light ash which can be easily wiped away with
a damp cloth, once the oven is cool.
10
Cleaning
Do not select the pyrolysis function after every use,
only when the oven is very dirty or produces smoke
or fumes while preheating or cooking.
• If the oven is installed below a hob, make sure
that all burners or electric hotplates are switched
off during the self-cleaning (pyrolysis) function.
• Remove all accessories before running the
pyrolysis function (also the lateral grids).
• For optimum cleaning of the oven door, remove
the worst soiling with a damp sponge before
using the pyrolytic function
2. Standard cycle (PYRO): which is suitable for
cleaning a very dirty oven.
• In any case, after a certain number of uses and
depending on how dirty the oven is, a message
on the oven display advises you to run a selfcleaning cycle.
N.B: during the pyrolysis function, the oven
door will not open; it will remain locked until
the temperature inside the oven has returned
to an acceptably safe level.
The appliance is equipped with 2 pyrolysis functions:
1. Energy-saving cycle (PYRO EXPRESS/ECO):
which consumes approximately 25% less energy
than the standard cycle. Select it at regular
intervals (after cooking meat on 2 or 3
consecutive occasions).
Maintenance
WARNING
- Use protective gloves.
- Ensure the oven is cold before carrying out the following
operations.
- Disconnect the appliance from the mains power supply.
REMOVING THE DOOR
To remove the door:
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (fig. 1).
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is
released (D) (fig. 2).
(fig. 1)
To refit the door:
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door.
(fig. 2)
11
Maintenance
REMOVING THE SIDE GRILLES
The side accessory-holder grilles are equipped with two fixing screws (fig. 3)
for optimum stability.
1. Remove the screws and relative plates on the right and left with the aid
of a coin or tool (fig. 4).
2. To remove the grilles, lift them up (1) and turn them (2) as shown in
fig. 5.
REPLACING THE LAMP
To replace the rear lamp (if present):
1. Disconnect the oven from the mains power supply.
2. Unscrew the lamp cover, replace the lamp (see note for lamp type) and
screw the lamp cover back on.
3. Reconnect the oven to the power supply.
N.B:
- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 2040W/230 V type G9, T300°C halogen lamps.
- The lamp used in the appliance is specifically designed for electrical
appliances and is not suitable for household room illumination
(Commission Regulation (EC) No 244/2009).
- Lamps are available from our After-Sales Service.
(fig. 3)
(fig. 4)
IMPORTANT:
- If using halogen lamps, do not handle with bare hands
sincefingerprints can damage them.
- Do not use the oven until the lamp cover has been repositioned.
(fig. 5)
12
Instructions for oven use
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
3
1
6
2
7
5
12
4
13
8
11
10
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Control panel
Upper heating element/grill
Cooling fan (not visible)
Dataplate (not to be removed)
Lamps
Circular heating element (not visible)
Fan
Rotisserie (if supplied)
Bottom heating element (not visible)
Door
Position of shelves (the number of shelves is indicated on the front of the oven)
Rear wall
Meat probe connection
N.B:
- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a
while.
- When the oven door is opened during cooking, the heating elements switch off.
13
Instructions for oven use
ACCESSORIES SUPPLIED
A. WIRE SHELF: the wire shelf can be used to grill food or as a support
for pans, cake tins and other ovenproof cooking receptacles.
(Fig. A)
B. DRIP TRAY: the drip tray is designed to be positioned under the wire
shelf in order to collect fat or as an oven tray for cooking meat, fish,
vegetables, focaccia, etc.
(Fig. B)
C. BAKING TRAY: for cooking all bread and pastry products, but also
roasts, fish en papillotte, etc.
(Fig. C)
D. MEAT PROBE: to measure the core temperature of food during
cooking.
(Fig. D)
E. TURNSPIT: for uniform roasting of large pieces of meat and poultry.
(Fig. E)
F. SLIDING SHELVES (if present): for easier handling of shelves and trays.
(Fig. F)
The number of accessories may vary according to which model is purchased.
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-Sales Service.
14
Instructions for oven use
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).
2. The other accessories, like the drip tray and baking tray, are inserted with the raised part on the flat
section “B” facing upwards (Fig. 2).
(Fig. 1)
(Fig. 2)
CONTROL PANEL DESCRIPTION
DISPLAY
1
3
4
1. FUNCTIONS KNOB: On/off and function selector knob
2. BROWSE KNOB: for browsing the menu and adjusting pre-set values
3. BUTTON
: to return to the previous screen
4. BUTTON
: to select and confirm settings
15
2
Instructions for oven use
LIST OF FUNCTIONS
Turn the "Functions" knob to any position and the oven switches on: the display shows the functions or the
associated submenus.
D
A. Symbol for highlighted function
B. Highlighted function can be selected by pressing
C. Description of highlighted function
D. Other available and selectable functions
Professional
A
Traditional
B
Special functions
Traditional manual cooking functions
C
FUNCTION DETAILS
After selecting the desired function, the display will show further options and related details.
Zone 1
Zone 2
Medium
--:--
GRILL POWER
NO
Grill
PREHEAT.
Start
CURSOR
COOK TIME
Zone 3
--:--
Zone 4
END TIME
Zone 5
To move between the different zones, use the "Browse" knob: the cursor moves to the adjustable values,
following the order described above.
Press button
to select the value, change it by turning the "Browse" knob and confirm with button
FIRST USE - SELECTING A LANGUAGE AND SETTING THE TIME
For correct use of the oven, when it is switched on for the first time you will have to select the desired
language and set the correct time.
Proceed as follows:
1. Turn the "Functions" knob to any position: the display will show the list of the first three available
languages.
2. Turn the "Browse" knob to scroll the list.
3. When the desired language is highlighted, press
will flash 12:00.
to select it. After language selection, the display
4. Set the time by turning the "Browse" knob.
5. Confirm your setting by pressing
.
16
.
Instructions for oven use
SELECTING COOKING FUNCTIONS
TEMPO COTTURA
POTENZA GRILL
NO
PRERISC.
TEMPO COTTURA
POTENZA GRILL
Grill
Avvio
--:--
Media
--:--
Media
NO
--:--
PRERISC.
TEMPO FINE
Grill
Avvio
--:-TEMPO FINE
1. If the oven is off, turn the "Functions" knob; the display will show the cooking functions or associated
submenus.
N.B: for the list and description of functions, see the specific table at page 26.
2. Within the submenus, browse the various options available by turning the "Browse" knob: the chosen
function is highlighted in white in the centre of the screen. To select it, press
.
3. The cooking settings are shown on the display. If the pre-set values are those desired, turn the
“Browse” knob to position the cursor at "Start" and then press
; otherwise, proceed as indicated
above to change them.
SETTING THE TEMPERATURE/OUTPUT OF THE GRILL
To change the temperature or output of the grill, proceed as follows:
1. Check that the cursor is positioned next to the temperature value (zone 1); press button
the parameter to be changed: the temperature values flash.
2. Set the desired value by turning the "Browse" knob and press
3. Turn the "Browse" knob to position the cursor at
"Start" and then press
.
4. The display indicates which shelf food should be
placed on. Do as instructed and press
to
start cooking. The set temperature can also be
changed during cooking by following the same
procedure.
to confirm.
180°C
--:-COOK TIME
TEMPERATURE
NO
PREHEAT.
Conventional
Start
180°C
PREHEAT.
--:--
Conventional
Start
200°C
PREHEAT.
--:--
Conventional
Start
200°C
PREHEAT .
17
--:-END TIME
--:-COOK TIME
TEMPERATURE
NO
--:-END TIME
COOK TIME
TEMPERATURE
NO
--:-END TIME
COOK TIME
TEMPERATURE
NO
to select
Conventional
Start
--:-END TIME
Instructions for oven use
PREHEATING THE OVEN
If you do not wish to preheat the oven, for those functions which allow it, simply change the oven's default
selection as follows:
1. Turn the "Browse" knob to position the cursor
--:-200°C
at preheating.
COOK TIME
TEMPERATURE
2. Press button
to select the setting: "Yes"
flashes on the display.
YES
PREHEAT.
3. Change the setting by turning the "Browse"
knob: "No" appears on the display.
4. To confirm your choice, press button
Conventional
Start
200°C
--:-COOK TIME
TEMPERATURE
YES
PREHEAT.
.
Conventional
Start
--:-COOK TIME
TEMPERATURE
Conventional
NO
Start
PREHEAT.
--:-END TIME
200°C
--:-COOK TIME
TEMPERATURE
Conventional
NO
PREHEAT.
Start
--:-END TIME
FAST PREHEATING
If you wish to preheat the oven quickly before inserting food, proceed as follows:
180°C
TEMPERATURE
Press +/- to adjust ...
Start
18
--:-END TIME
200°C
1. Turn the "Functions" knob to select the fast
preheating function.
2. Confirm by pressing
: the settings are
shown on the display.
3. If the proposed temperature is that desired,
turn the “Browse” knob to position the cursor
at “Start” and then press
. To change the
temperature, proceed as described in previous
paragraphs. An acoustic signal will sound when
the oven has reached the set temperature. At
the end of preheating, the oven automatically
selects the conventional function
.
At this point food can be placed in the oven for
cooking.
4. If you wish to set a different cooking function,
turn the "Functions" knob and select the desired
function..
--:-END TIME
Instructions for oven use
SETTING COOKING TIME
This function can be used to cook food for a set length of time, from a minimum of 1 minute to the
maximum time allowed by the selected function, after which the oven switches off automatically.
1. To select the function, turn the “Browse” knob to
position the cursor at "cook time".
180°C
Conventional
NO
2. Press button
to select the setting; "00:00"
flashes on the display.
Start
PREHEAT.
3. Change the value by turning the "Browse" knob to
display the desired cooking time.
4. Confirm the selected value by pressing button
--:-COOK TIME
TEMPERATURE
.
--:-END TIME
180°C
-00:30
TEMPERATURE
HH:MM
Conventional
NO
Start
PREHEAT.
180°C
00:01
COOK TIME
TEMPERATURE
Conventional
NO
Start
PREHEAT.
180°C
PREHEAT.
19:01
END TIME
-00:30
COOK TIME
TEMPERATURE
NO
19:01
END TIME
Conventional
Start
19:20
END TIME
BROWNING
At the end of cooking, with certain functions, the display indicates the possibility of browning the surface
of your dish. This function can only be used when
cooking time has been set.
At the end of cooking time, the display shows “+/to prolong,
Cooking finished at 20:00
to brown.
+/- to prolong.,
to brown".
Press button
, and the oven starts a 5 minute
browning cycle. This function can only be used
once after cooking.
-00:05
COOK TIME
Browning
20:05
END TIME
Browning until 20:05
19
Instructions for oven use
SETTING END OF COOKING TIME/ DELAYED START
The end of cooking time can be set, delaying the start 180°C
-00:30
COOK TIME
of cooking by up to a maximum of 23 hours and 59
TEMPERATURE
minutes. This can only be done once cooking time
Conventional
NO
19:20
has been set. This setting is only possible when
PREHEAT.
END TIME
Start
preheating is not required for the selected
function. After setting cooking time, the display
-00:30
180°C
shows the end of cooking time (for example 19:20).
HH:MM
TEMPERATURE
To delay the end of cooking time, and thus also the
Conventional
cooking start time, proceed as follows:
NO
19:20
PREHEAT.
END TIME
Start
1. Turn the "Browse" knob to position the cursor at
the end of cooking time.
-00:30
180°C
2. Press button
to select the setting: the end of
COOK TIME
TEMPERATURE
cooking time flashes.
Conventional
NO
20:10
3. To delay the end of cooking time, turn the
PREHEAT.
END TIME
Start
"Browse" knob to set the desired value.
4. Confirm the selected value by pressing button
. 180°C
-00:30
COOK TIME
TEMPERATURE
5. Turn the "Browse" knob to position the cursor at
START and then press
.
Conventional
NO
20:10
6. The display indicates which shelf food should be
PREHEAT.
END TIME
Start
placed on. Do as instructed and press
to start
-00:30
cooking. The oven will start cooking after a period 180°C
COOK TIME
of time calculated so as to finish cooking at the set TEMPERATURE
time (for example, in the case of a dish which
Conventional
NO
20:10
requires a cooking time of 20 minutes, if the end
PREHEAT.
END TIME
Start
of cooking time is set to 20.10, the oven will begin
-00:29
180°C
cooking at 19.50).
COOK TIME
TEMPERATURE
N.B: during the interval before cooking starts,
Conventional
the oven can in any case be switched on by
NO
20:10
PREHEAT.
END TIME
Start
turning the “Browse” knob to position the
cursor at "Start" and then pressing button
.
At any time, set values (temperature, grill setting, cooking time) can be changed as described in
previous paragraphs.
20
Instructions for oven use
TIMER
This function can be used only with the oven switched off and is useful, for example, for monitoring the
cooking time of pasta. The maximum time which can be set is 1 hour 30 minutes.
1. With the oven off, press button
: the
display will show "00:00:00".
2. Turn the "Browse" knob to select the
desired time.
3. Press button
to start the countdown.
When the set time has elapsed, the
display will show "00:00:00" and an
acoustic signal will sound. At this point
the time can be prolonged, proceeding as
described above
, or the timer can be
deactivated by pressing button (the time
of day will be shown on the display).
00 : 00 : 00
(HH) (MM) (SS)
Turn +/- to set the timer,
to Start
00 : 30 : 00
(HH) (MM) (SS)
Turn +/- to set the timer,
to Start
01 : 09 : 00
Timer
PROFESSIONAL FUNCTIONS
Thanks to the professional functions, you can choose from 17 recipes. The oven offers a suitable function
for every type of recipe category and also advises the ideal temperature and shelf for cooking the dish. For
advice on use of these functions, refer to the Recipe Book, which contains a number of recipe ideas that
you can personalize to suit your own taste. The available functions are given below. The time and
temperature for each recipe are indicated on the oven display and/or in the Recipe Book. For
recipes listed in the Professional Roasting Function, there is the option of using the Meat Probe (see
paragraph).
Professional Bakery Function
Traditional Bread
Malt Bread
Pan Pizza
Thin Pizza
Savoury Pie
Baguette
Professional Pastry Function
Patè a Choux
Croissant/Brioches
Sponge Cake
Plum Cake
Short Pastry
Professional Roasting Function
Veal - Pork
Roast Beef Rare
Roast Beef Medium
Roast Chicken
Roast Turkey
Custom (customizable function for cooking meat).
21
Instructions for oven use
MEAT PROBE
The meat probe supplied allows you to measure the exact core
temperature of food during cooking, between 0°and 100°C, in order to
ensure that food is cooked to perfection. Based on the food being
cooked, the required core temperature can be set. It is very important to
position the probe accurately in order to obtain perfect cooking results.
Insert the probe fully into the fleshiest part of the meat, avoiding bones
and fatty parts (fig. A). For poultry, the probe should be inserted
sideways, in the middle of the breast, taking care to ensure the tip does
not end up in a hollow part (fig. B). In the case of meat with very irregular
thickness, check it is cooked properly before removing it from the oven.
Connect the end of the probe in the hole located on the right wall of the
oven chamber.
The probe can be used with the following functions:
• Conventional
• Convection Bake
• Forced Air
• Turbogrill
• Tweli-grill (where present)
• Slow Cooking Meat and Slow Cooking Fish
• Pro Roasting.
If the probe is not inserted, cooking proceeds in the traditional
180°C
mode (fig. 1), otherwise, the display advises that the probe is
TEMPERATURE
not connected (Fig. 2). After the confirmation message, the
display shows all the cooking parameters selected:
YES
- at the top left (zone 1) the oven temperature;
PREHEAT.
- at the top right (zone 3) the desired core temperature of the
food (meat probe, as indicated in Fig. 3).
To start cooking, turn the "Browse" knob to position the cursor
at "Start" and then press
.
The bottom right (zone 4) of the cooking screen shows the
"current" core temperature of food (fig. 4). In the first two
minutes, the desired temperature of food (meat probe, as
indicated in Fig. 4) can be changed. After two minutes, this
indication is replaced by the cooking time (Fig. 5). When the
150°C
desired core temperature for the particular food is reached, a
message to that effect appears on the display for 3 seconds (Fig. TEMPERATURE
6). Subsequently, the oven proposes the option of prolonging
cooking time by turning the "Browse" knob towards +. If no
button is pressed, the oven continues cooking for 6 minutes in
order to ensure excellent results. If cooking time is prolonged,
this is displayed at the top right (zone 3). At the end of cooking,
150°C
the display indicates the possibility of "browning" (for those
TEMPERATURE
functions which allow it).
NOTES:
1. When two minutes have elapsed since the start of cooking, to
change the desired core temperature of food, the meat probe
must be disconnected and then reconnected again.
150°C
2. If the meat probe is inserted before a function has been
TEMPERATURE
selected, only cooking functions without preheating will be
selectable. For recipes which require preheating, insert the food
with the meat probe only after preheating.
3. In "Pro Roasting" preheating is included for all recipes.
Consequently, avoid inserting the meat probe or food before
150°C
preheating has finished.
fig. A
fig. B
--:-COOK TIME
Conventional
--:-END TIME
Fig. 1
Meat probe
has been connected
Fig. 2
100°C
MEAT PROBE
Conventional
Fig. 3
100°C
MEAT PROBE
Conventional
79°C
CURRENT
Fig. 4
00:10
TEMPO COTTURA
Conventional
79°C
CURRENT
Fig. 5
30:00
TEMPERATURE
COOK TIME
Temperature reached
100°C
CURRENT
Fig. 6
22
Instructions for oven use
FAVOURITES
This oven allows you to memorize the settings used to cook
your favourite dishes.
At the end of cooking, if you wish to save the settings used
(function, time, temperature...), press the
button.
At this point, the display shows the message "Presse
save".
Press
to save
to cancel
to
Press button
and the oven will propose the first available
position from 1 to 10. If you wish to customize the position, you
can change the number by turning the "BROWSE" (+/-) knob
before confirming your choice with button
.
2
Press
Forced air
to save
to cancel
When the memory is full or the position is already in use, the
function is overwritten.
Favourite has been saved
If, on the other hand, you do not wish to memorize the settings,
simply press the button
, proceed to another function by
turning the "BROWSE" knob or switch off the oven. To subsequently view saved settings, turn the
"FUNCTIONS" knob until the display shows the symbol
then select one of the stored functions,
turning the "BROWS" (+/-) knob until the desired function is displayed.
Press button
followed by button
to start cooking.
SETTINGS
1. To change some display settings, select "SETTINGS" from the main menu menu by turning the
"Functions" knob.
2. Confirm by pressing
: the display shows which settings can be changed (language, volume of
acoustic signal, display brightness, time, energy saving function, power).
3. The setting to be changed by turning the "Browse" knob.
4. Press button
to confirm.
5. Follow the instructions of the display to change the settings.
6. Press button
; a message appears on the display confirming your selection.
N.B: When the oven is switched off, if the ECOMODE (Energy saving) function is selected (ON), the
display switches off after a few minutes, showing the clock. To view information on the display and switch
the light on again, just press any of the buttons or turn one of the knobs. During a cooking function if the
ECOMODE is activated the cavity lamp will be switched off after 1 minute of cooking and reactivated for
each user interaction. If, on the other hand, the function is not selected (OFF), after a few minutes the
display is merely dimmed.
KEY-LOCK
This function can be used to lock the control panel buttons.
To activate it, press
and
at the same time for at least 3 seconds.
If activated, the functions of the buttons are locked and the display shows a message and the symbol
.
This function can also be activated during cooking.
To deactivate it, repeat the above procedure. When the key-lock function is activated, the oven can only
be switched off by turning the knob to 0 (zero). In this case, however, the previously selected function will
have to be set again.
23
Instructions for oven use
AUTOMATIC OVEN CLEANING
For the description of this function, see the chapter
CLEANING and the functions table on page 24.To
start the oven's automatic cleaning cycle (pyro)
proceed as follows:
Pyro Express
Pyrolytic
3 hour high temperature cleaning
1. Using the "Functions" knob, select "Cleaning".
The display shows "Pyro Express" and "Pyro".
-03:00
TIME
15:00
Cleaning
2. Select one of the two cleaning cycles using the
"Browse" knob. 2. Confirm by pressing
.
END TIME
3. Turn the "Browse" knob to position the cursor at
START, then confirm by pressing
.
1/3
Please switch off cooktop above oven and press
4. The display shows the instructions to be followed
in order to start the cycle. After following each
instruction, confirm with button
.
2/3
Please remove all accessories from the oven and press
3/3
Remove stains from glass with moist sponge, press
24
Instructions for oven use
5. Upon the final confirmation, the oven starts the
cleaning cycle and the door is automatically
locked: a warning and the symbol
are shown
on the display for around three seconds.
Immediately afterwards, the display shows a
progress bar indicating the cleaning cycle
progress.
The door will remain locked
during cleaning
-02:59
TIME
Cleaning
15:00
END TIME
Note: If the oven door is opened before it is
unlocked automatically, a warning message
appears on the display. When the door is
reclosed, the cycle must be started again by
pressing button
.
Please close door
-00:00
TIME
6. At the end of the cycle, the relative message
flashes on the display, after which the cooling bar
indicates cooling in progress.
Finished
The residual temperature is indicated on the
display together with the symbol
15:00
END TIME
257°
.
The door remains locked until the temperature
inside the oven has returned to an acceptably
safe level: the display shows the time of day..
Cooling down
18:32
25
Functions description table
MAIN MENU
Function
Function
Description of Function
SETTINGS
Setting the display (language, time, brightness, volume of acoustic signal, energy saving
function)
PROFESSIONAL
FUNCTIONS Roasting Bakery
Pastry
Specific functions for the type of dish chosen, with the ideal temperature recommended.
The oven chamber is automatically prepared with optimum preheating, and cooking is
managed automatically with a dedicated cycle for each recipe. Option of using the meat
probe accessory for perfect cooking times for Roasting functions. (SEE COOKBOOK).
TRADITIONAL
see TRADITIONAL FUNCTIONS
SPECIALS
see SPECIAL FUNCTIONS
TRADITIONAL FUNCTIONS
FAST PREHEATING
To preheat the oven rapidly.
CONVENTIONAL
To cook any kind of dish on one shelf only. Use the 3rd shelf. To cook pizza, savoury pies
and sweets with liquid fillings, use the 1st or 2nd shelf.
GRILL
To grill steak, kebabs and sausages; to cook vegetables au gratin and toast bread. Place
food on the 4th or 5th shelf. When grilling meat, use the drip tray to collect the cooking
juices.
Position it on the 3rd/4th shelf, adding approx. half a litre of water. The oven does not
have to be preheated. During cooking the oven door must remain closed.
TURBOGRILL
To roast large joints of meat (legs, roast beef, chickens). Position the food on the middle
shelves. Use the drip tray to collect the cooking juices. Position it on the 1st/2nd shelf,
adding approx. half a litre of water. The oven does not have to be preheated. During
cooking the oven door must remain closed. With this function you can also use the
rotisserie, if provided.
FORCED AIR
To cook a variety of food requiring the same cooking temperature on several shelves
(maximum three) at the same time (e.g: fish, vegetables, cakes). This function can be
used to cook different foods without odours being transferred from one food to another.
Use the 3rd shelf to cook on one shelf only, the 1st and 4th to cook on two shelves, and
the 1st, 3rd and 5th to cook on three shelves.
CONVECTION BAKE
To cook meat and pies with liquid filling (savoury or sweet) on a single shelf. Use the 3rd
shelf. Preheat the oven before cooking.
26
Functions description table
SPECIAL FUNCTIONS
Function
Function
Description of Function
DEFROST
To speed up defrosting of food. Place food on the middle shelf. Leave food in its
packaging in order to prevent it from drying out on the outside.
KEEP WARM
For keeping just-cooked food (e.g. meat, fried food, flans) hot and crisp. Place food on
the middle shelf. The function will not activate if the temperature in the oven is above
65°C.
RISING
For optimal rising of sweet or savory dough. Place the dough on the 2nd shelf. The oven
does not have to be preheated. To safeguard the quality of proving, do not activate the
function if the oven is still hot after a cooking cycle.
SLOW COOKING
MEAT
SLOW COOKING
FISH
To gently cook meat (at 90°C) and fish (at 85°C). This function offers slow cooking
which ensures the food remains tender and succulent. Thanks to the low temperature,
the food does not brown on the outside and the end result is similar to steam cooking.
For roast joints, brown in the pan first in order to seal in the meat's natural juices.
Cooking times range from 2 hours for fish weighing 300g to 4-5 hours for fish weighing
3 kg; for meat, times range from 4 hours for 1Kg joints to 6-7 hour for 3 kg joints. For
optimum results, do not open the oven door during cooking, as this results in heat
dispersion; use the meat probe (if provided) or a standard oven thermometer.
YOGHURT
For preparing homemade yoghurt. Use small china jars or aluminium foil baking cups.
Cover with aluminium foil during cooking. Position the drip tray with the containers on
the 1st shelf. The oven does not have to be preheated.
AUTOMATIC
CLEANING
To burn off spatters produced during cooking with an extremely high temperature cycle
(approx. 500°). Two auto-cleaning cycles are available : a complete cycle (PYRO) and a
shorter cycle (EXPRESS). The complete cycle is best used only in the case of very dirty
ovens, while the shorter cycle should be used at regular intervals.
FAVOURITES
To access the 10 favourite functions. For storing and using favourites, see the paragraph
"FAVOURITES".
ECO FORCED AIR
To cook stuffed roasts and meat in pieces on one shelf. This function uses discontinuous,
delicate fan assistance, which prevents excessive drying of foods. In this ECO function
the light remains off during cooking and can be temporarily switched on again by
pressing the confirm button. In order to maximize energy efficiency, it is advisable not to
open the door during cooking. It is advisable to use 3nd level. The oven does not have
to be preheated.
27
Cooking table
Recipe
Function
Preheating
Shelf (from Temperature
Time (min)
bottom)
(°C)
YES
2-3
160 - 180
30 - 90
–
1-4
160 - 180
30 - 90
Accessories
Cake tin on wire shelf
Leavened cakes
Shelf 4: cake tin on wire shelf
Shelf 1: cake tin on wire shelf
–
3
160 - 200
35 - 90
–
1-4
160 - 200
40 - 90
Filled pies (cheesecake,
strudel, fruit pie)
drip tray/ baking tray or
wire shelf + cake tin
Shelf 4: cake tin on wire shelf
Shelf 1: cake tin on wire shelf
YES
3
170 - 180
20 - 45
–
1-4
150 - 170
20 - 45
Biscuits/Tartlets
Drip tray / baking tray
Shelf 4: baking tray
Shelf 1: drip tray
Shelf 5: oven tray on wire
shelf / baking tray
–
1-3-5
150 - 170
20 - 45
–
3
180 - 200
30 - 40
Drip tray / baking tray
–
1-4
180 - 190
35 - 45
Shelf 4: oven tray on wire
shelf / baking tray
Choux buns
Shelf 3: baking tray
Shelf 1: drip tray
Shelf 1: drip tray
Shelf 5: oven tray on wire
shelf / baking tray
–
1-3-5
180 - 190
35 - 45
–
3
90
110 - 150
Drip tray / baking tray
–
1-4
90
140 - 160
Shelf 4: oven tray on wire
shelf / baking tray
Meringues
Shelf 3: baking tray
Shelf 1: drip tray
Shelf 1: drip tray
–
1-3-5
90
140 - 160
YES
1/2
190 - 250
15 - 50
–
1-4
190 - 250
25 - 50
Shelf 5: oven tray on wire
shelf / baking tray
Shelf 3: baking tray
Shelf 1: drip tray
Drip tray / baking tray
Shelf 4: oven tray on wire
shelf / baking tray
Shelf 1: drip tray / baking tray
Bread / Pizza / Focaccia
Shelf 5: oven tray on wire
shelf / baking tray
–
1-3-5
190 - 250
25 - 50
Shelf 3: oven tray on wire
shelf / baking tray
Shelf 1: drip tray
28
Cooking table
Recipe
Function
Preheating
Shelf (from
bottom)
Temperature
Time (min)
(°C)
–
3
250
10 - 20
–
1-4
230 - 250
10 - 25
Frozen pizza
Accessories
Shelf 3: drip tray / baking tray or
wire shelf
Shelf 4: oven tray on wire shelf /
baking tray
Shelf 1: drip tray
Savoury pies
(vegetable pie, quiche)
–
3
180 - 190
40 - 55
–
1-4
180 - 190
45 - 60
Cake tin on wire shelf
Shelf 4: cake tin on wire shelf
Shelf 1: cake tin on wire shelf
Shelf 5: cake tin on wire shelf
–
1-3-5
180 - 190
45 - 60
Shelf 3: cake tin on wire shelf
Shelf 1: drip tray / baking
tray + cake tin
–
3
190 - 200
20 - 30
–
1-4
180 - 190
20 - 40
Vols-au-vent /
Puff pastry crackers
Drip tray / baking tray
Shelf 4: oven tray on wire shelf
Shelf 1: drip tray / baking tray
Shelf 5: oven tray on wire shelf
–
1-3-5
180 - 190
20 - 40
Shelf 3: oven tray on wire shelf /
baking tray
Shelf 1: drip tray
Lasagne / Baked pasta /
Cannelloni / Flans
–
3
190 - 200
45 - 65
Drip tray or oven tray on wire
shelf
Lamb / Veal / Beef /
Pork 1 Kg
–
3
190 - 200
80 - 110
Drip tray or oven tray on wire
shelf
Chicken / Rabbit / Duck 1 Kg
–
3
200 - 230
50 - 100
Drip tray or oven tray on wire
shelf
Turkey / Goose 3 Kg
–
2
190 - 200
80 - 130
Drip tray or oven tray on wire
shelf
Baked fish / en
papillote (fillet, whole)
–
3
180 - 200
40 - 60
Drip tray or oven tray on wire
shelf
Stuffed vegetables
(tomatoes, courgettes,
aubergines)
–
2
180 - 200
50 - 60
Oven tray on wire shelf
Toast
–
5
3 (High)
3-6
wire shelf
Fish fillets / steaks
–
4
Mid
20 - 30
Shelf 4: wire shelf (turn food
halfway through cooking)
15 - 30
Shelf 5: wire shelf (turn food
halfway through cooking)
Shelf 3: drip tray with water
Sausages / Kebabs /
Spare ribs / Hamburgers
–
5
Mid-High
Shelf 4: drip tray with water
29
Cooking table
Recipe
Roast chicken 1-1.3 Kg
Function
Preheating
Shelf (from Temperature
Time (min)
bottom)
(°C)
–
2
Mid
55 - 70
Accessories
Shelf 2: wire shelf (turn food
two thirds of the way
through cooking if
necessary)
Shelf 1: drip tray with water
Liv. 2: Turnspit (if present)
Roast chicken 1-1,3 Kg
–
2
High
60 - 80
Liv. 1:Drip tray with water
Roast Beef rare 1Kg
–
3
Mid
35 - 50
Leg of lamb / Shanks
–
3
Mid
60 - 90
Roast potatoes
–
3
Mid
35 - 55
Vegetable gratin
–
3
High
10 - 25
Lasagne & Meat
–
1-4
200
50 - 100*
Meat & Potatoes
–
1-4
200
45 - 100*
Fish & Vegetables
–
1-4
180
30 - 50*
Oven tray on wire shelf
(turn food two thirds of the
way through cooking if
necessary)
Drip tray or oven tray on
wire shelf (turn food two
thirds of the way through
cooking if necessary)
Drip-tray / baking tray (if
necessary, turn food two
thirds of the way through
cooking)
Drip tray or oven tray on
wire shelf
Shelf 4: oven tray on wire
shelf
Shelf 1: drip tray or oven
tray on wire shelf
Shelf 4: oven tray on wire
shelf
Shelf 1: drip tray or oven
tray on wire shelf
Shelf 4: oven tray on wire
shelf
Shelf 1: drip tray or oven
tray on wire shelf
Shelf 5: oven tray on wire
shelf
Full meal:
Tart (Shelf 5) /
Lasagne (Shelf 3) /
Meat (Shelf 1)
–
Filled roast meats
–
3
200
80 - 120*
Drip tray or oven tray on
wire shelf
Meat cuts (rabbit,
chicken, lamb)
–
3
200
50 - 100 *
Drip tray or oven tray on
wire shelf
1-3-5
190
40 - 120*
Shelf 3: oven tray on wire
shelf
Shelf 1: drip tray or oven
tray on wire shelf
* Cooking time is merely for guidance, and refers to the entire cooking cycle. Remove food at different
times, according to personal preference.
30
Table of Tested Recipes
(in compliance with IEC 60350-1:2011-12 and DIN 3360-12:07:07)
Recipe
Function
Preheating
Shelf
Temperature
(from bottom)
(°C)
Time
(min)
Accessories and note*
Drip tray / baking tray
EC 60350-1:2011-12 § 7.5.2
YES
3
170
15 - 30
–
1-4
150
30 - 45
Shortbread
Shelf 4: baking tray
Shelf 1: Drip tray / baking tray
IEC 60350-1:2011-12 § 7.5.3
YES
3
170
25 - 35
–
1-4
160
30 - 40
Drip tray / baking tray
Shelf 4: baking tray
Small cakes
Shelf 1: drip tray / baking tray
–
1-3-5
160
35 - 45
Shelf 5: oven tray on wire shelf / baking tray
Shelf 3: baking tray
Shelf 1: drip tray / baking tray
YES
2
170
30 - 40
Cake tin on wire shelf
–
1-4
175
75 - 95
EC 60350-1:2011-12 § 7.6.1
Fatless sponge cake
Shelf 4: cake tin on wire shel
Shelf 1: cake tin on wire shelf
IEC 60350:2009-03 § 8.5.2
–
2/3
185
70 - 90
–
1-4
175
75 - 95
2 Apples pies
Cake tin on wire shelf
Shelf 4: cake tin on wire shelf
Shelf 1: cake tin on wire shelf
IEC 60350-1:2011-12 § 9.2
Toast**
–
5
High
3-6
–
5
High
18 - 30
Wire shelf
IEC 60350-1:2011-12 § 9.3
Shelf 5: wire tray (turn food halfway through cooking)
Burgers**
Shelf 4: drip tray with water
DIN 3360-12:07 § 6.5.2.3
Apple cake, yeast tray
cake, Gedeckter
apfelkuchen
–
3
180
35 - 45
–
1-4
160
55 - 65
Drip tray / baking tray
Shelf 4: baking tray
Shelf 1: drip tray / baking tray
DIN 3360-12:07 § 6.6
Pork Roast
–
2
190
150 - 170
Shelf 2: drip-tray
YES
3
170
40 - 50
Drip tray / baking tray
–
1-4
160
45 - 55
DIN 3360-12:07 annex C
(Flat cake)
Shelf 4: baking tray
Shelf 1: drip tray / baking tray
31
Table of Tested Recipes
The cooking table advises the ideal function and cooking temperature to ensure the best results with all
recipes. If you wish to cook on one shelf only using the convection bake function, place food on the third
shelf and select the temperature recommended for the "FORCED AIR" function when cooking on more
than one shelf.
The indications given in the table are intended without the use of the sliding runners. Conduct
tests without the sliding runners.
* When not provided, accessories can be purchased from after sale service.
** When grilling food, leave a space of 3-4 cm at the front to facilitate removal from the oven
Energy efficiency class (in accordance with EN 60350-1:2013-07)
Use the relevant table to conduct tests
Energy consumption and preheating time
Select the function and carry out the test with only the " Preheating" option activated. ("Preheating yes")
Recommended use and tips
How to read the cooking table:
The table indicates the best function to use for any given food, to be cooked on one or more shelves at
the same time. Cooking times start from the moment food is placed in the oven, excluding preheating
(where required). Cooking temperatures and times are purely for guidance and will depend on the amount
of food and type of accessory used. Use the lowest recommended values to begin with and, if the food is
not cooked enough, then move on to higher values. Use the accessories supplied and preferably dark
coloured metal cake tins and oven trays. You can also use pans and accessories in pyrex or stoneware, but
bear in mind that cooking times will be slightly longer. To obtain best results, carefully follow the advice
given in the cooking table for the choice of accessories (supplied) to be placed on the various shelves.
Cooking different foods at the same time
Using the "FORCED AIR" function, you can cook different foods which require the same cooking
temperature at the same time (for example: fish and vegetables), using different shelves. Remove the food
which requires less cooking time and leave food which requires longer cooking time in the oven.
Desserts
- Cook delicate desserts with the conventional function on one shelf only. Use dark coloured metal cake
tins and always position them on the wire shelf supplied. To cook on more than one shelf, select the
forced air function and stagger the position of the cake tins on the shelves, aiding optimum circulation
of the hot air.
- To check whether a raising cake is cooked, insert a wooden toothpick into the centre of the cake. If the
toothpick comes out clean, the cake is ready.
- If using non-stick cake tins, do not butter the edges as the cake may not rise evenly around the edges.
- If the cake "sinks" during cooking, set a lower temperature the next time, perhaps reducing the amount
of liquid in the mixture and mixing more gently.
- For sweets with moist fillings (cheesecake or fruit pies) use the "CONVECTION BAKE" function. If the
base of the cake is soggy, lower the shelf and sprinkle the bottom of the cake with breadcrumbs or
biscuit crumbs before adding the filling.
32
Recommended use and tips
Meat
- Use any kind of oven tray or pyrex dish suited to the size of the piece of meat being cooked. For roast
joints, it is best to add some stock to the bottom of the dish, basting the meat during cooking for added
flavour.
Take great care, as this procedure generates very hot steam. When the roast is ready, let it rest in the
oven for another 10-15 minutes, or wrap it in aluminium foil.
- When you want to grill meat, choose cuts with an even thickness all over in order to achieve uniform
cooking results. Very thick pieces of meat require longer cooking times. To prevent the meat from
burning on the outside, lower the position of the wire shelf, keeping the food farther away from the
grill. Turn the meat two thirds of the way through cooking, taking care to avoid the steam when
opening the oven door.
To collect the cooking juices it is advisable to place a drip-tray with half a litre of water directly under
the grill on which the food is placed. Top-up when necessary.
Tips for dishes cooked using the traditional functions
Recipe
Shelf
(from bottom)
Recommended cooking
temperature (°C)
Recommended end
temperature for
meat probe (°C)
Roast beef rare
2/3
200 - 220
48
Roast beef medium
2/3
170 - 190
60
Roast beef well done
2/3
170 - 190
68
Roast turkey
1/2
150 - 170
75
Roast chicken
2/3
200 - 210
83
Roast pork
2/3
170 - 190
75
Roast veal
2/3
160 - 180
68
Rotisserie (only in some models)
Use this accessory to roast large pieces of meat and poultry. Fit the cradle on the second shelf level. Place
the meat on the rotisserie rod, tying it with kitchen string in the case of poultry, then secure both ends of
the meat with the two purpose-designed forks, ensuring the meat is secure on the rod. Insert the rod in
the aperture on the front wall of the oven and rest it on the support. To prevent smoke and to collect
cooking juices, it is advisable to place the drip-tray with at least half a litre of water on the first shelf. The
rod has a plastic handle which must be removed before starting cooking, and which can be used at the end
of cooking to avoid burns when taking the food out of the oven.
Pizza
Lightly grease the trays to ensure the pizza has a crispy base. Scatter the mozzarella over the pizza two
thirds of the way through cooking.
Rising function (present only in specific models)
It is always best to cover the dough with a damp cloth before placing it in the oven. Dough proving time
with this function is reduced by approximately one third compared to proving at room temperature
(20-25°C). Proving time for a 1 Kg batch of pizza dough is around one hour.
33
Printed in Italy
02/15
400010768077
n
GB
Download PDF

advertising