KitchenAid KSCX 3610 Instruction for Use

KSCX 3610
Instructions for use
1 Product description
4
2 Important notes
8
Important information for the correct disposal of the product
in accordance with EC directive 2002/96/EC
8
Building-in
9
3 Before first use
11
4 Using for the first time
12
5 Preparing coffee (using coffee beans)
13
6 Changing the quantity of coffee in the cup
15
7 Regulating the coffee mill
15
8 Preparing espresso coffee using ground coffee
(instead of beans)
16
9 Hot water delivery
17
10 Preparing cappuccinos (using steam)
17
11 Cleaning and maintenance
18
12 Changing and setting the menu parameters
20
13 Changing the language
22
14 Meaning of messages and what to do
23
15 Problems that can be resolved before calling
the Customer Care Centre
24
After-Sales Service
26
1 Product description
B
Q
C
I
L
D
V
N
G
E
O
H
F
P
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.
Main ON/OFF switch
Lights
Steam spout
Water tank (removable)
Cup tray
Drip tray (removable)
Service door
Coffee spout (adjustable in height)
Control panel
Bean container lid
Central ground coffee lid
Infuser
Power cable
Cappuccino maker (removable)
Cappuccino maker nozzle
(removable)
Measure for pre-ground coffee
Coffee grounds container
(removable)
Grinding coarseness regulator
Coffee beans container
Compartment for measure
Ground coffee funnel
Mobile drawer
Accessories holder
J
K
T
S
R
U
M
A
W
4
1 Product description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5
1 Product description
17
18
19
20
21
22
23
24
25
26
27
6
1 Product description
Control Panel
1. Display
2. Appliance ON/OFF knob
3. Coffee taste selection button
4. One or two cups short coffee button
5. One or two cups standard coffee button
6. One or two cups long coffee button
7. Button to select ground coffee or, if the MENU
light is on, to display the next parameter on the
menu
8. Button to select hot water or OK to confirm
9. Button to rinse the appliance or, if the MENU
light is on, to change the menu parameters
10. Button to activate or deactivate menu
parameter setting mode (MENU)
11. MENU light
12. Steam knob
then release.
They work just like a
switch.
To use the knobs,
turn them clockwise…
7
2 Important notes
READ THESE INSTRUCTIONS CAREFULLY AND
KEEP FOR FUTURE CONSULTATION!
• This appliance is designed to "make espresso
coffee" and "heat drinks". Use with care to avoid
scalds from the water and steam jets or through
incorrect use.
• This appliance is intended for domestic use only.
Any other use is considered improper and thus
dangerous.
• Do not hang to the appliance when it is
extracted.
• The manufacturer is not liable for damage
caused by improper, incorrect or unreasonable
use of the appliance.
• When using the appliance, do not touch the hot
surfaces. Use the knobs or handles.
• Never touch the appliance with any wet part of
the body or operate it with bare feet.
• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety. Children should be supervised to
ensure that they do not play with the appliance.
• In the event of failure or malfunction, unplug the
appliance from the mains and do not tamper
with it in any way. If it requires repair, contact
an authorised service centre only and ask for
original spare parts to be used. Failure to
respect the above could reduce the safety of
the appliance.
• This appliance may be installed above a
conventional built oven provided it is fitted with
a cooling blower on the top side. The nominal
power of the oven shall not be more than 3Kw.
• Do not rest objects containing liquids,
inflammable or corrosive materials; use the
accessories holder to contain coffee accessories
(for example coffee measure). Do not rest big
objects that may block the movement of the
appliance or unstable objects.
• Avoid exposing the appliance to atmospheric
agents.
• The parts which could come into contact with
coffee or milk conform to the provisions of the
EEC directive 1935/2004 relating to materials
suitable for contact with foodstuffs.
• This appliance conforms to EC directive
2004/108/EC on Electromagnetic Compatibility
(EMC).
Important information for the correct disposal of the product in
accordance with EC directive 2002/96/EC
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused by inappropriate waste handling of
this product.
The symbol
on the product, or on the documents accompanying the product, indicates that this
appliance may not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact
your local city office, your household waste disposal service or the shop where you purchased the
product.
8
Building-in
Please check the minimum measures (mm) necessary to the proper installation of the appliance.
The coffee maker must be installed in a column unit, which must in turn be securely fixed to the wall with
standard brackets.
Fasten metal strip
using the two screws.
.
Min
ventilation passageway
80
450
455
20
550
.
Min
560
50
850
368
80
Min.
361
74
527
Minimum distance
595
ATTENTION:
• Important: the appliance should be disconnected from the mains during installation or
maintenance work.
• The kitchen units coming into direct contact with the appliance must be heat resistant (min. 80°C).
• To ensure correct ventilation, leave an opening at the bottom of the unit (following the sizes in the
drawing).
9
.
Min
Building-in
1
2
16
Lean the bars to the surface of the furniture.
Fix the bars with the screws provided; then
completely extract the two bars.
In case of installation above a "warmer drawer",
use the top of the latter as a reference for the
coffee maker runners. In this case, there will be no
support surface.
Put the appliance on its housing and fasten it with
the screws.
3
4
1
10
mm
x. 350
appro
Fix the power cord with the special clip, to avoid
the cord entangling when extracting or inserting
the appliance. The power cord must be long
enough to allow the extraction of the appliance for
refilling the coffee bean container.
Regulations require that the appliance must be
earthed. The electrical connection must be
made by a qualified electrician in compliance
with the manufacturer’s instructions and
applicable local regulations.
To align the appliance correctly, put the spacers
under the bar’s support.
10
3 Before first use
• After removing the packaging, make sure the
product is complete and undamaged. If in
doubt, do not use the appliance and contact a
qualified professional.
• Installation must be carried out by a qualified
techncian and in compliance with current
regulations.
• Packing elements (plastic bags, polystyrene etc)
must not be left within reach of children as they
may represent a hazard.
• Never install the appliance in environments
where the temperature may reach 0°C or lower
(the appliance may be damaged if the water
freezes).
• Make sure the mains voltage corresponds to the
voltage indicated on the appliance rating plate.
Connect the appliance to an efficiently earthed
socket with a minimum current rating of 10A
only. The manufacturer may not be considered
liable for possible incidents caused by the failure
to adequately earth the mains.
• If the power socket does not match the plug on
the appliance, have the socket replaced with a
suitable type by a qualified professional.
• Observance of safety directives requires that a
multi pole switch with a minimum contact gap
of 3 mm be used for the installation.
• Do not use multiple plug adapters or extension
leads.
• The power cable on this appliance must not be
replaced by the user as this operation requires
the use of special tools. If the cable is damaged
or requires replacing, contact an authorised
service centre only to avoid all risks.
For the electrical connection use a H05 VV-F
type cable as indicated in the table below:
To learn how to operate the appliance correctly,
when you use it for the first time, follow the stepby-step instructions given in the following chapters.
Amount x Size
Conductors
220-240 V ~ +
• You should personalise water hardness as soon
as possible following the instructions in
paragraph 12.6.
• The appliance's DATA PLATE is positioned on
the side of the coffee maker so that it remains
visible after installation when the machine is
removed from its housing.
~
3 x 1.0 mm2
11
4 Using for the first time
The first time you turn on the appliance and every time that it is plugged in, when you turn the main ON/OFF
knob clockwise (A), the appliance makes a SELF-DIAGNOSIS operation and then turns itself off. To turn it on
again, rotate the ON/OFF knob (2) clockwise on the control panel.
1. The first time you use the appliance, select the language.
Press the main ON/OFF switch on the rear side of the appliance; the lights on the front side and the
display illuminate. Wait for the appliance to display:
PRESS OK TO INSTALL ENGLISH
Press the
button for at least 3 seconds until the appliance displays:
ENGLISH INSTALLED
The appliance then displays the setting message in English.
2. After a few seconds, the appliance displays:
FILL TANK
To fill, remove the tank (fig. 1), rinse and fill with fresh water. Never exceed the MAX line. (When
removing the tank, the cappuccino maker must always be positioned towards the centre of the
appliance, otherwise the tank cannot be removed).
Put the tank back and push as far as it will go.
Move the cappuccino maker outwards (fig. 2) and place a cup underneath it.
3. The appliance now displays:
PRESS OK
Press the
button. After a few seconds, a little water runs out of the cappuccino maker. When the
cup contains about 30cc of water, the water stops running and it switches off.
4. The appliance now displays:
TURNING OFF PLEASE WAIT .. .
and it goes off.
5. Extract the appliance by pulling it outwards taking care to use the special handles, open the lid and the
container with coffee beans (fig. 3), then close the lid and push the appliance inwards the appliance.
IMPORTANT: to prevent malfunction, never fill with ground coffee, freeze dried coffee, caramelised
beans or anything else which could damage the appliance.
6. Turn the ON/OFF knob (fig. 4), The appliance displays:
HEATING UP PLEASE WAIT ...
to indicate that preheating is underway.
7. When preheating is complete, the appliance displays:
RINSING COMPLETE PLEASE WAIT ...
and performs an automatic rinse cycle (a little hot water runs out of the spouts and is collected in the
drip tray beneath).
Tip: if you want to make a short coffee (less than 60 cc), to make it hotter, fill the cup with this hot rinsing
water first. Leave it for a few seconds then empty it to warm the cup.
8. The appliance now displays the ready message:
READY STANDARD TASTE
12
5 Preparing coffee (using coffee beans)
1. The appliance is preset to make coffee with a standard strength. ‘You can also choose coffee with
different strengths. To choose the required strength, press the
button (fig.5): and the selected
coffee strength will be displayed.
2. Place 1 cup under the spouts to make 1 coffee (fig. 6) or 2 cups for 2 coffees (fig. 7). For a creamier
coffee, lower the spouts to bring them as close to the cups as possible (fig. 8).
3. Press the
button to make a short coffee, the
button for a standard coffee and the
button
for a long coffee (fig. 9).
To make 2 coffees, press the button twice (within 2 seconds).
To change the quantity of coffee delivered automatically into the cup, follow the instructions
in chapter 6.
(The appliance now grinds the beans and starts running off the coffee into the cup. Once the desired
quantity has been reached, the appliance automatically stops delivering the coffee and ejects the
grounds into the special container).
4. After a few seconds, the ready message is displayed again and you can make another coffee.
5. To turn the appliance off, turn the main knob to the OFF position.
Before switching off, the appliance performs an automatic rinse cycle (a little hot water runs out from
the spouts and is collected in the drip tray beneath). Take care to avoid scalds.
Once switched off, the lights will not shut off immediately and the cooling span motor
operates to avoid condensation in the housing. After about 30 minutes, the appliance
switches completely off.
NOTE 1: If the coffee is delivered a drop at a time or not at all, turn the grinding coarseness regulator (fig. 10)
one click clockwise (see chapter 7).
Turn one click at a time until the coffee is delivered satisfactorily.
NOTE 2: If the coffee is delivered too fast and is not creamy enough, turn the grinding coarseness regulator
(fig. 10) one click anticlockwise (see chapter 7).
Avoid turning the grinding coarseness regulator excessively otherwise when you select 2 cups, the coffee
may run out in drips.
NOTE 3: Tips to make hotter coffee:
• When you turn the appliance on, if you want to make a short coffee (less than 60 cc), use the hot
rinse-through water to preheat the cups.
If 2/3 minutes have passed, since you last made coffee, before making coffee again you must preheat
the infuser by pressing the
button (fig. 11).
Run off the water into the underlying drip tray or alternatively use this water to fill (and then empty)
the cup to be used for the coffee, so as to preheat it.
• Unless preheated, do not use cups that are too thick, as they will absorb too much heat.
• Use cups that have been preheated by rinsing them with hot water or by leaving them for at least 20
minutes on the cup warmer tray on top of the appliance with the appliance on.
NOTE 4: while the appliance is making the coffee, delivery can be stopped at any time by pressing the
,
or
button as previously selected.
NOTE 5: as soon as delivery is complete, to increase the quantity of coffee, simply press and hold the
,
or
button as previously selected, until the desired quantity is reached (this operation must
be performed within 3 seconds from when coffee delivery from the spouts ceases).
13
5 Preparing coffee (using coffee beans)
NOTE 6: when the appliance displays:
FILL TANK
the water tank must be refilled or the appliance will not make coffee.
(It is normal for there to be a little water left in the tank when the message is displayed).
NOTE 7: the appliance counts the number of coffees made.
Every 14 single coffees (or 7 doubles) the appliance displays:
EMPTY GROUNDS CONTAINER
indicating that the grounds container is full and must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance continues to
display the message and cannot make coffee.
To clean, open the service door at the front by pulling the coffee spout (fig. 12),
remove the drip tray (fig. 13), empty and clean. When proceeding, always
completely extract the drip tray, to avoid it falling when removing the grounds
container.
Empty the grounds container and clean thoroughly, making sure all residues
deposited on the bottom are removed.
IMPORTANT: when removing the drip tray, the grounds container MUST be
emptied, even if it is not completely full. If this is not done, when next making
coffee the grounds in the container may exceed the maximum level and block the
appliance.
NOTE 8: while the appliance is running off coffee, never remove the water tank. If it is removed, the
appliance will not be able to make the coffee.
When using the appliance for the first time, 4-5 cups of coffee need to be made before the
appliance starts to give satisfying results.
If the appliance malfunctions, do not contact the Customer Care Centre straight away.
The problem can almost always be resolved by following the instructions indicated in chapters 14 and 15.
If this is not the case, or for further explanations, contact the Customer Care Centre by calling the number
listed on page 2 of the enclosed sheet.
If your country is not listed on the sheet, call the number indicated on the warranty.
14
6 Changing the quantity of coffee in the cup
The appliance is factory preset to automatically deliver the following quantities of coffee:
- short (when the
button is pressed);
- standard (when the
button is pressed);
- long (when the
button is pressed);
To change these quantities, proceed as follows:
- press the button corresponding to the quantity you want to change (
,
or
) for at least 8
seconds until the message "PROGRAM QUANTITY" is displayed;
- when the coffee in the cup reaches the required level, press the same button again to memorise the
new amount.
7 Regulating the coffee mill
However, after making the first few coffees, if you find that coffee delivery is either too fast or too slow (in
drips), the grinding coarseness regulator can be adjusted (fig. 10).
Turning it 1 click (1 number) clockwise speeds up coffee delivery (without drips).
Turning it 1 click anticlockwise slows down delivery giving a creamier appearance to the coffee.
These adjustments will only be evident after at least 2 cups of coffee have been run off.
The grinding coarseness regulator must only be turned when the coffee mill is on.
Turn anticlockwise to obtain finer ground coffee, slower delivery and a creamier
appearance.
Turn clockwise for coarser ground coffee and faster delivery (not a drop at a time).
(Coffee has been used to factory test the appliance and it is therefore completely normal for there to be
traces of coffee in the mill. This appliance is however guaranteed to be new).
15
8 Preparing espresso coffee using ground coffee
(instead of beans)
• Press the
(fig. 14) button to select the ground coffee function. This disables the coffee mill
function.
The appliance displays
READY PRE-GROUND
• Extract the appliance by pulling it using the special handles (fig. 3).
• Lift the central lid, place one level measure of ground coffee in the funnel (see fig. 15). Close the lid,
push the appliance to replace it and proceed as described in chapter 5. Note: You can make just one
coffee at a time by pressing the
,
or
button once only.
NOTE 1: Never add the ground coffee when the appliance is off to avoid it being dispersed inside the
appliance.
NOTE 2: Never add more than one level measured scoop, otherwise either the appliance
will not make the coffee, the ground coffee will be lost inside the appliance, dirtying it, or
the coffee will run off in drips and the message "GROUND TOO FINE ADJUST GRINDER
AND PRESS OK" will be displayed. A little water comes out from the steam spout.
NOTE 3: When dosing the quantity of coffee to be added, use the measure supplied only.
NOTE 4: Use ground coffee for espresso coffee makers only. Do not use coffee beans, freeze-dried
coffee or other materials that could damage the appliance.
NOTE 5: If the funnel blocks due to moisture inside the appliance or if more than one measuring scoop of
pre-ground coffee has been used, use a knife to push the coffee down (Fig. 16), then remove and clean the
infuser and appliance as described in chapter 11.2 "Cleaning the infuser".
• Once the coffee has been delivered, to go back to making coffee using beans, deactivate the ground
coffee function by pressing the
button again (the light goes off and the coffee mill is enabled for
operation again).
16
9 Hot water delivery
• Always make sure the appliance is ready.
• Turn the cappuccino maker towards the outside of the appliance and place a container under it (fig. 2).
• Press the
(fig. 17). The appliance displays:
HOT WATER PRESS OK
• Press the
/
button again (fig. 17) for hot water.
• Hot water runs off from the cappuccino maker and starts to fill the container underneath. You should
not run off hot water for more than 2 minutes at a time.To interrupt hot water delivery, press the
button again (fig. 17) and place the cappuccino maker in the original position near the centre of the
appliance.
Note: if you accidentally push the
/
button, push any other button to abort the function or wait
until the appliance automatically turns back to the main menu.
10 Preparing cappuccinos (using steam)
• Move the cappuccino maker outwards (fig. 2).
• Place an empty container under the cappuccino maker. Turn the steam knob (fig. 18). The appliance
displays:
STEAM press OK
• Press the
button (fig. 17) for steam.
Allow the steam mixed with water to run off for a few seconds until steam only is given off.
• To interrupt steam delivery, turn the steam knob counter clockwise the steam knob (fig. 18).
Note: if you accidentally turn the steam knob, push any button, except the
button, to abort the
function or wait until the appliance automatically turns back to the main menu.
• Empty the container then fill it with about 100 grams of milk for each cappuccino to be prepared. In
choosing the size of the container, bear in mind that the milk doubles or triples in volume. You are
recommended to use semi-skimmed milk at refrigerator temperature.
• Dip the cappuccino maker into the milk (fig. 2), taking care not to immerse the raised line on the
cappuccino maker (indicated by the arrow in fig. 19). Press the steam button (beware of burns). Steam
is discharged from the cappuccino maker, giving the milk a creamy frothy appearance.
To obtain a creamier froth, dip the cappuccino maker into the milk and rotate the container with slow
movements from the bottom upwards. (You should not discharge steam for more than two minutes at
a time).
• Once the required temperature is reached, interrupt steam delivery by pressing the steam button (fig.
18). Prepare the coffee as described above, using large enough cups, then fill with the frothed milk
prepared previously. The cappuccino is ready. Sweeten to taste and, if desired, sprinkle the froth with a
little cocoa powder.
IMPORTANT: always clean the cappuccino maker immediately after use. Proceed as follows:
• Discharge a little steam for a few seconds by pressing the steam button. This empties any milk left
inside the steam spout.
IMPORTANT: to guarantee hygiene, you are recommended to follow this procedure each time you
make cappuccino to avoid milk stagnating in the milk circuit.
17
10 Preparing cappuccinos (using steam)
• Press the steam button.
• Wait a couple of minutes for the cappuccino maker to cool down then with one hand hold the
cappuccino spout handle firm and with the other unscrew the cappuccino maker itself by rotating
clockwise and extracting downwards (fig. 20).
• Remove the nozzle from the steam spout by pulling it downwards (fig. 21).
• Carefully wash the cappuccino maker and steam nozzle in warm water.
• Make sure the two holes shown in fig. 22 are not blocked. If necessary, clean with a pin.
• Replace the steam nozzle by inserting it and vigorously turning it upwards into the steam spout.
• Replace the cappuccino maker by pushing it upwards and turning it counter-clockwise.
11 Cleaning and maintenance
Before performing any cleaning operations, leave the appliance to cool down, switch off the main switch
and unplug from the mains socket.
Do not use solvents or abrasive cleaning products to clean the appliance. A soft damp cloth will suffice.
NEVER wash ANY of the components of the appliance in a dishwasher.
11.1 Cleaning the coffee maker
Clean the grounds container (as described in chapter 5, note 7) whenever it requires emptying.
The water tank should also be cleaned regularly.
The drip tray is fitted with a level indicator (red) showing the level of water it contains.
When the indicator starts to become visible (a few millimetres under the drip tray), the drip tray must be
emptied and cleaned.
Check that the holes in the coffee spout are not blocked. To unblock them, scrape the dry coffee residues
away with a needle (fig. 23).
11.2 Cleaning the infuser
The infuser must be cleaned regularly to avoid the build-up of coffee encrustations which could cause
malfunction.
Proceed as follows:
• turn the appliance off by rotating the
knob counter-clockwise (fig. 4) (do not switch off the main
switch or unplug) and wait for the display to go off;
• open the service door (fig. 12);
• remove the drip tray and the grounds container (fig. 13) and clean;
• press the two red release buttons on the infuser sideways and towards the centre (fig. 24) and pull it
out;
• IMPORTANT: THE INFUSER CAN ONLY BE REMOVED WHEN THE APPLIANCE IS OFF.
ATTEMPTING TO REMOVE THE INFUSER WITH THE APPLIANCE ON MAY CAUSE SERIOUS
DAMAGE.
18
11 Cleaning and maintenance
• Wash the infuser under running water, without using detergents. Never wash the infuser in the
dishwasher;
• clean the inside of the appliance thoroughly. To remove coffee encrustations from the inside of the
appliance, scrape with a plastic or wooden fork (fig. 25) then vacuum up the residues with a vacuum
cleaner (fig. 26);
• replace the infuser by sliding it onto the supports and pin at the bottom, then push the PUSH symbol
fully in until it clicks into place.
Infuser
Push the PUSH symbol fully
in until it clicks into place.
After having heard the click,
check that the red buttons
have snapped out.
Support
Bottom pipe on the infuser.
The pin must be inserted into the
bottom pipe on the infuser.
Pin
Check that the two red buttons have snapped out, otherwise the door cannot be closed.
The two red buttons
have snapped out
CORRECTLY
The two red buttons
have not snapped out
INCORRECT
CORRECT
NOTE 1: If the infuser is not inserted correctly until it clicks into place and the two red buttons have not
snapped out, the service door cannot be closed.
NOTE 2: If it is hard to insert the infuser, before inserting it squeeze it to the right size by pressing it
forcefully from the top and bottom simultaneously, as shown in figure 27.
NOTE 3: If it is still hard to insert the infuser, leave it out of the appliance, close the service door, unplug
from the mains then plug in again.
Wait for all the lights to go off, then open the door and replace the infuser.
• replace the drip tray, complete with the grounds container;
• close the service door.
19
12 Changing and setting the menu parameters
The following menu parameters and functions can be changed by the user:
• Clock
• Auto-start time
• Descaling process
• Coffee temperature
• Length of time the appliance remains on
• Water hardness Factory default values
12.1 Setting the clock
To set the clock, proceed as follows:
• Press the
(the light over the button comes on) then press the
appliance displays
button repeatedly until the
CLOCK 00:00
• Press the
rapidly).
• Press the
button to set the clock. (If you hold the
, button down, the time is changed
button to confirm the value;
• Press the
button to exit programming mode or
to change other parameters.
When the appliance is in stand-by, you can see the hour by pressing any one of the buttons (except
the ON/OFF button).
12.2 Setting auto-start time
This enables you to set automatic start times.
• Make sure the clock on the appliance is set as described above.
• Press the
button then press the
button repeatedly until the appliance displays:
START TIME 00:00
• Press the
button to set the auto-start time. (If you hold the
changed rapidly).
• Press the
button to confirm the value,
• Press
once and the appliance displays the message:
, button down, the time is
AUTO-START NO
Press the
• Press the
• Press the
button to modify the function (the appliance displays AUTO-START YES);
button to activate auto-start;
button to exit programming mode or the
button to change other parameters.
12.3 Descaling
Over time, the continuous heating up of the water used to make the coffee leads to lime scale building up
in the inner circuits of the appliance.
When the appliance displays the message:
DESCALE
you should perform the descale cycle.
Proceed as follows:
• make sure the appliance is ready.
• press the
button (the light over the button comes on) then press the
until the appliance displays:
DESCALE NO
• Press
and the appliance displays the message:
• Press the
button to start the descale programme.
DESCALE YES
20
button repeatedly
12 Changing and setting the menu parameters
• Empty the tank and pour in the contents of one bottle (125 ml) of DURGOL descaler plus one litre of
water.
For subsequent descaling operations, descaling solution can be purchased from authorised technical
service centres.
NB: Make sure splashes of descaler do not fall onto surfaces sensitive to acid such as marble, limestone and
glaze.
• Place a container with a minimum capacity of 1.5 litres under the cappuccino maker (fig. 2);
• The descaling solution will run out of the cappuccino maker and start to fill the container underneath
• The descale programme automatically performs a series of run offs and pauses to remove lime scale
deposits from inside the coffee maker.
• After about 30 minutes, the appliance displays:
RINSING FILL WATER TANK
The appliance must now be rinsed through to eliminate residues of descaling solution from inside the
appliance. Proceed as follows:
• Remove the water tank, rinse and fill with clean water.
• Reposition the tank: the appliance display RINSING PRESS OK.
• Empty the collection container (under the cappuccino maker) full of liquid and then put it back under
the cappuccino maker.
• Press the
button (fig. 17).
Hot water is run off from the cappuccino maker into the container below and the appliance displays:
RINSING
• When the water tank is empty, the appliance displays the message:
RINSE COMPLETE PRESS OK BUTTON
• Press the
button (fig. 17) and refill the water tank with clean water.The descale programme is now
terminated and the appliance is ready to make coffee again.
NOTE: if the descaling cycle is interrupted before completion, the appliance continues to display the
descale message and the programme must be started again from the beginning.
IMPORTANT: FAILURE TO DESCALE THE APPLIANCE REGULARLY INVALIDATES THE GUARANTEE.
12.4 Changing coffee temperature
To change the temperature of the coffee, proceed as follows:
• Press the
button (the light over the button comes on) then press the
until the appliance displays:
button repeatedly
TEMPERATURe MEDIUM
• Press the
• Press the
• Press the
button until the appliance displays the required coffee temperature
button to confirm the temperature selected;
button to exit programming mode or
to change other parameters.
12.5 Changing the length of time the appliance remains on
The appliance is factory preset to go off automatically one hour after the last coffee has been made.
The number of hours the appliance remains on can be increased as follows:
• Press the
button (the light over the button comes on) then press the
button repeatedly
until the appliance displays:
OFF AFTER 1 HOUR
• Press the
• Press the
• Press the
button to change the number of hours the appliance remains on
button to confirm the value;
button to exit programming mode or
to change other parameters.
21
12 Changing and setting the menu parameters
12.6 Setting water hardness
The appliance is preset to display the descale message after a set period of time, based on a set water
hardness. You can make descaling less frequent by programming the appliance based on the actual lime
content in the water used. Proceed as follows:
• Remove the "Total Hardness Test" strip from its packaging then dip it fully in the water for a few
seconds, Remove it and wait around 30 seconds (until it changes colour and a number of red dots are
formed);
• Turn the appliance on by pressing the
• Press the
button then press the
button (fig. 4).
button repeatedly until the appliance displays:
WATER HARDNESS 4
• Press the
button repeatedly until the number coincides with the number of red squares on the
test strip (for example, if there are 3 red squares on the test strip, press the button until WATER
HARDNESS 3 is displayed).
• Press the
button to confirm the value. The coffee maker is now programmed to provide the
descaling warning when necessary, based on the actual hardness of the water.
12.7 Resetting factory default settings
If you change the original values, the factory default values can be reset as follows:
• Press the
, button then press the
button repeatedly until the appliance displays:
RESET TO DEFAULT NO
• Press the
• Press the
• Press the
button and the appliance displays “RESET TO DEFAULT YES”;
button to reset the factory default values;
button to exit programming mode or
to change other parameters.
13 Changing the language
To change the language, proceed as follows:
• Press the
button for at least 5 seconds until the appliance displays:
PRESS OK TO INSTALL ENGLISH
and press the
button for at least 3 seconds to confirm. The appliance then displays the setting
message in English.
22
14 Meaning of messages and what to do
MESSAGE
MEANING
• The water tank is empty or is
positioned incorrectly.
FILL TANK
GROUND TOO FINE
ADJUST MILL AND
PRESS THE OK BUTTON
• The tank is dirty or encrusted
with lime scale.
EMPTY GROUNDS CONTAINER
ADD PRE-GROUND COFFEE
FILL BEAN CONTAINER
DESCALE
PRESS NEXT+ CHANGE
• Empty the grounds container
and clean as described in
chapter 5, note 7, then
replace.
• Open the service door and
insert the grounds container.
• After cleaning, the grounds
container has not been
replaced.
• With the ground coffee
• Add the ground coffee as
function selected, ground
described in chapter 8.
coffee has not been poured
into the funnel.
• The coffee beans have run out. • Fill bean container.
• If the coffee grinder is very
• Contact an authorised service
noisy, this means a small stone
centre.
in the coffee beans has blocked
the mill.
• This indicates the presence of
lime scale in the appliance.
• After cleaning, the infuser has
probably been left out of the
coffee maker.
• The service door is open.
CLOSE DOOR
INSERT INFUSER
• Fill the water tank as described
in chapter 5, note 6 and insert
it fully.
• Rinse or descale the tank.
• The appliance cannot make
• Press the OK button (fig. 17).
coffee.
• The coffee runs off too slowly. • Turn the grinding regulator (fig.
10) one click clockwise (see
chapter 7).
• The grounds container is full.
INSERT GROUNDS CONTAINER
WHAT TO DO
• After cleaning, the infuser has
probably been left out of the
coffee maker.
• The inside of the appliance is
very dirty.
GENERAL ALARM
23
• The descaling procedure,
described in chapter 12.3,
needs to be performed as
soon as possible.
• Leave the service door closed
and the infuser out of the
appliance, then follow the
instructions displayed.
• If the service door cannot be
closed, check that the infuser
is inserted correctly (chapter
11.2 - note 1).
• Insert the infuser, see chapter
11.2.
• Thoroughly clean the inside of
the appliance, as described in
chapter 11.2. If the message is
still displayed after cleaning,
contact a service centre.
15 Problems that can be resolved before calling the Customer
Care Centre
If the appliance is not working properly, the causes of the malfunction can be identified and resolved by
referring to chapter 14. If, on the other hand, no message is displayed, run the following checks before
calling the customer care centre.
PROBLEM
The coffee is not hot
CAUSE
SOLUTION
• The cups have not been
preheated.
•
The coffee is not creamy •
enough
•
• Heat the cups by rinsing them in hot
water or leaving them for at least 20
minutes on the cup warmer tray on the
lid (see note 3, chapter 5).
• Heat the infuser by pressing the
The infuser is too cold
button before making the coffee (fig.
11, see note 3, chapter 5).
The coffee is ground too
• Turn the grinding regulator one click
coarsely
anticlockwise (see chapter 7).
Wrong type of coffee
• Use a type of coffee for espresso coffee
makers.
The coffee is ground too finely. • Turn the grinding regulator one click
clockwise (see chapter 7).
The coffee runs out too
slowly.
•
The coffee runs out too
quickly.
• The coffee is ground too
coarsely.
• Turn the grinding regulator one click
anticlockwise (see chapter 7).
The coffee does not
come out of one of the
spouts.
When the steam button
is pressed, no steam
comes out of the
cappuccino maker.
• The spout holes are blocked.
• Scrape off the dry coffee residues with
a needle (fig. 23).
• The holes in the cappuccino
maker and steam nozzle are
clogged.
• Clean the holes in the cappuccino
maker and the steam nozzle (see
chapter 10 - fig. 22).
When the
,
or
, button is pressed,
the appliance does not
deliver coffee, but only
water.
• The ground coffee may be
blocked in the funnel.
• Remove the ground coffee inside the
funnel using a knife (see chapter 8 note 5). Then clean the infuser and the
inside of the appliance (see description
in chapter 11.2).
When the
knob is
turned, the appliance
does not switch on.
The infuser cannot be
removed for cleaning.
• The appliance is not plugged in • Check that the power cable is plugged
or the main switch on the rear
into the mains socket and the main
side of the appliance is not
switch is in the ON position.
switched on.
• The appliance is on. The
• Turn the appliance off and remove the
infuser can only be removed if
infuser (see chapter 11.2).
the appliance is off.
IMPORTANT: the infuser can only be
removed if the appliance is off.
Attempting to remove the infuser when
the appliance is on may cause serious
damage.
24
15 Problems that can be resolved before calling the Customer
Care Centre
PROBLEM
CAUSE
SOLUTION
Ground coffee is being
• Too much ground coffee has
used (not beans) and the
been added.
appliance does not pour
the coffee.
• The
button has not
been pressed and the
appliance has used both the
ground coffee added and the
coffee ground by the mill.
• Ground coffee has been added
when the appliance is off.
The coffee does not run • The holes in the spouts are
out from the spouts, but
clogged with dry coffee.
from around the service • The mobile container inside
door.
the service door is blocked
and cannot swing.
25
• Remove the infuser and thoroughly
clean the inside of the appliance, as
described in chapter 11.2. Repeat the
operation using a maximum of 1
measure of ground coffee.
• Thoroughly clean the inside of the
appliance, as described in chapter 11.2.
Repeat the operation, first pressing the
button as described in chapter 8.
• Remove the infuser and thoroughly
clean the inside of the appliance, as
described in chapter 11.2. Repeat the
operation, but switch the appliance on
first
• Scrape the holes with a needle (see
chapter 11.1, Fig. 23).
• Thoroughly clean the mobile container,
particularly near the hinges to ensure
they are free to swing smoothly.
After-Sales Service
Before contacting the Customer Care Centre:
Switch the appliance on again to see if the problem
has been eliminated. If it has not, switch off the
appliance and repeat the operation after one hour.
If your appliance still does not work properly after
carrying out the checks listed in the
troubleshooting guide and switching the appliance
on again, contact the Customer Care Centre,
clearly explaining the problem and specifying:
• the appliance type and serial number (given on
the rating plate).
• the type of fault.
• the model.
• the Service number (the number after the word
SERVICE on the rating plate inside the appliance).
• your full address.
• your telephone number and area code.
26
Printed in Italy
11/07
5019 744 02005
n
GB