EN
Quick guide
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.hotpoint.eu/register
Before using the appliance carefully read the Safety Instructions.
CONTROL PANEL
1 On/Off button (Reset if long pressed)
2 Programme selection Knob
3 Start/Pausa
Options Buttons*
4 Dryness Level
5 Timed Drying
6 Start Delay
7 Gentle
8 Crease Care (Key Lock if long pressed)
9 Cycle End
END
9
1
180’
120’
9h
90’
6h
60’
30’
8
3h
DEMO
3“
1h
h
2
4
5
6
3
7
*Note: some models may have the wording in full instead of the icons
INDICATORS
Dryness Level: . Iron Dry Hanger Dry - Cupboard Dry Extra Dry
Cycle Phase:
Drying - Cool Down - END End of Cycle
Empty Water tank Clean Door filter Clean Bottom filter Refer to Troubleshooting Section:
Failure: Call after Sales Service. DEMO Demo Mode
FIRST TIME USE
PROGRAMMES
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dyrer is properly fixed,
either to the dryers's water tank or to the domestic sewage
system.
The dryer should be installed in environment in a room
temperature range of 20°to 23°C for optimum performance. But
will function if the room is between 14 and 30°C. Before you use
your dryer ensure that it has been in a upright position for at
least 6 hours.
Should you wish to change the opening side of the door, please
contact our After-sales Service. (See phone number in the
warranty booklet).
1.Mixed
kg 4 Time 106'
This programme is ideal for drying cotton and synthetic fabrics
together.
2.Eco cotton
kg Max* Time 215'
Standard cotton programme, suitable to dry normally wet
cotton laundry. Most efficient programme in terms of energy
consumption for drying cotton laundry. The values on the Energy
Label are based on this programme.
3.Synthetics
kg 4 Time 96'
This programme is suitable for synthetic garments or cotton
blends/synthetic.
4.Wool kg 1 Time 62'
Programme for drying wool clothing. It is advisable to turn the
garments inside out before drying. Leave to dry naturally the heaviest
edges that are still damp.
5.Silk kg 0,5 Time 66'
Gentle drying of silk garments.
6.Anti Allergy
kg Max* Time 252'
This cycle has the “Allergy UK” approval of “The British Allergy
Foundation” attesting the effective reduction and elimination of
allergens. It can be used both with damp load (drying and treatment)
and dry load (half load only).
7.Daily
kg 2 Time 140'
Ideal for drying garments of cotton blends or synthetics spun at
high speed in the washing machine.
8.Cuddly toys Kg 2.5 Time 220'
The cycle preserves the original appearance and brilliance of the
cuddly toys at best. Remove all accessories before proceeding
with drying. Every single piece must not exceed 600 gr.
DAILY USE
Doing this will keep your machine working at its BEST!
Remember to empty your water tank after each drying cycle.
Remember to clean your filters after each drying cycle. (Refer to
section Care & Maintanence).
1. Open the door and load garments. Always refer to instructions
on clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door filter.
2. Close the door.
3. Press the button On/Off.
4. Select the programme according to the laundry type.
5. Select the options, if necessary.
6. To start the cycle, press the Start/Pause button.
7. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry.
8. Turn the machine off by pressing the button On/Off, open the
door and pull clothing out. If the machine is not switched off
manually, after about a quarter of an hour from the cycle end, the
appliance turns off automatically to save energy.
*MAX LOAD 8 Kg
If this last stage is not carried out immediately, some machines
You can download the
Instructions,
User
Manual,CARE
ProductLABEL
Fiche and Energy data by:
and/or some programmes/options
are Safety
equipped
with Crease
Care
xxxx
Visiting
ourthe
website
- docs.hotpoint.eu
system. For some• hours,
after
end of
drying, the drum rotates
Always check the care labels, especially when placing garments in
• Using
QR Code
at regular intervals
to prevent
the formation of creases.
the tumble
the firstbooklet).
time. Below
Alternatively,
contact
After-sales
Service
numberdryer
in thefor
warranty
When are the most commonly
In case of power •failure,
it is necessary
toour
press
the button
Start/(See phone
used
symbols:
contacting
our
After-sales
Service,
please
state
the
codes
provided
on
your
product’s
identifi
cation
plate.
Pause to restart the cycle.
May be tumble dried.
xxxxxxxxxxxx
OPENING OF THE DOOR DURING THE CYCLE
During operation, it is possible to open the door. After having
closed it, press the button Start/Pause again to restart the dryer.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
9.Refresh
A short programme suitable for refreshing fibres and
garments by means of fresh air. Do not use with garments that are
still wet. It can be used on with any load size but is more effective
with small loads. The cycle duration is about 20 minutes.
10.Duvet Time 179'
Programme intended to dry bulky garments, as single duvet.
11.Bed & Bath Kg Max* Time 240'
This programme is intended for drying cotton towels and
sheets.
12.Fitness Kg 4 Time 96''
For drying sports garments made of synthetics or cotton.
13.Baby
kg 2 Time 107'
A programme intended to dry garments and linen of newborn babies (cotton and chenille), as well as delicate garments.
Do not dry garments having plastic covering.
14.Jeans
kg 3 Time 127'
For drying cotton jeans-wear and garments made of robust
cotton, like denim, such as trousers and jackets.
15.Shirts
kg 3 Time 137'
This is a programme for Shirts made from cotton or cotton
blend/synthetics.
OPTIONS
After selecting the programme, the various options can be
set, if necessary
Dryness Level
Press the related button several times to obtain a different
level of residual moisture on garments. An indicator signals the
level being selected.
Iron Dry: a very delicate ironing. Suitable for making ironing
of garments easier immediately after the end of the cycle.
Hanger Dry: a level intended for delicate garments ready to
be hanged.
Cupboard Dry: the garments are ready to be folded and put
away.
Extra Dry: used for garments to be worn at the end of the
cycle.
h Start Delay
This option allows you to set the delay of the cycle start. Press
the corresponding button several times to obtain the required
delay. After having reached the max. settable time, the option is
reset by pressing the button again. An indicator on the control
panel signals the time being selected. After having pressed the
button Start/Pause, the machine signals the remaining time
for the cycle start. In case of door opening, after closing, it is
necessary to press the button Start/Pause.
Timed drying
This option allows to set the drying time. Press the
corresponding button to set the required time for drying. After
having reached the max. settable time, a further pressure of the
button resets the option. An indicator on the control panel signals
the time being selected.
OPTIONS BUTTONS
These buttons serves to personalise the selected programme
according to personal requirements. Not all options are available
for all programmes. Some options are incompatible with the
ones previously set. The buzzer and/or blinking indicators will
signal the incompatibility. If the option is available, the option
indicator will stay on. Some options may be kept in the memory
of the programme if selected in the previous drying.
Cycle End
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you are not sure to hear the normal sound at the
end of the cycle. This option remains in memory if selected in the
previous drying.
Gentle
Enables a more gentle treatment of the laundry by reducing the
drying temperature.
Key Lock
This option makes all machine controls inaccesible, except the
button On/Off. When the machine is on: to activate the option,
keep the button pressed until the indicator goes on.
To disable the option, keep the button pressed until the indicator
goes off. This option remains in memory if selected in the previous
drying.
Crease Care
This option add a crease treatment at the end of the cycle
by means of a periodic rotation of the drum (duration up to 10
hours). It is particularly suitable when it is not possible to remove
the laundry as soon as the drying ends. If this option is used
together with the Start Delay, the crease treatment is added
also in the Start Delay phase. This option remains in memory if
selected in the previous drying.
EN
Quick guide
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
CARE AND
In orderMANTENANCE
to receive a more complete assistance,
TRANSPORT AND HANDLING
BeforeNever
usinglift
the
carefully
read
Safety Instructions.
registerduring
your product
Unplugplease
the dryer
the on
cleaning and maintenance
theappliance
dryer by holding
it at
thethe
worktop.
www.hotpoint.eu/register
procedures.
1. Unplug the dryer.
Emptying the water tank after each cycle (see Fig. A)
2. Make sure that door and water tank are properly closed.
3. If the drain hose is connected to your sewage system, fix the
Pull the container out of the dryer and and empty it into a sink
drain hose on the rear of the dryer again (see Installation Guide).
or other suitable drain, then place it back. Do not use the dryer
without having inserted the container back in place.
Cleaning the door filter after each cycle (see Fig. B)
Pull the filter out and clean it by removing the lint from the filter
surface under running water or using a vacuum cleaner. Do not
use the dryer without having reinserted the filter in place.
Remove the door filter as described below:
1. Open the door and pull upwards.
2. Open the filter and
remove lint from all its parts. Replace it correctly.
Ensure it is completely inserted flush with the dryer seal.
Cleaning the bottom filter when the relevant indicator
turns on (see Fig. C)
Pull the filter out and remove the lint from its surface by
washing it under runing water or by using a vacuum cleaner.
However, it is advisable to clean this filter after each cycle to
optimise drying performance. Do not use the dryer without
having inserted the filter in place first.
Remove the bottom filter as described below:
1. Open the lower door.
2. Take the handle and pull the lower filter out.
3. Open the rear side of the filter and remove the lint from the
Power consumption
inner surface of the mesh.
off-mode (Po) - Watts
0.50
4. Clean the bottom filter chamber avoiding the direct contact
with the leaves.
left-on mode (Pl) - Watts
1.00
5. Close the rear side of the lower filter and place it back by
Programs
Kg
kWh
Minutes
checking it is perfectly integrated in place.
8
2.53
215
6. Lower the filter handle and close the bottom door.
Eco Cotton *
7. Make sure the air intake is free.
4
1.39
127
Eco Cotton
The filters are essential parts for drying. They are intended
to collect the lint formed during drying process. In case
of clogged filters, the air flow inside the dryer would be
seriously affected: the drying times would be longer, the
energy consumption would increase and the dryer could be
damaged. If these procedures are not carried out properly,
the dryer may not start.
Synthetics
4
1.18
116
*This is the reference programme for the energy label and suitable to
dry normal wet cotton laundry. This is the most efficient programme
in terms of energy consumption for drying wet cotton laundry.
(Standard/Default starting configuration)
Heat Pump System
The heat pump contains fluorinated greenhouse gases,
contained in a hermetically sealed unit. This sealed unit contains
0.15 kg of the F gas R134a. GWP = 1430 (1 t CO2).
PRODUCT DESCRIPTION
A
1. Water bottle
2. Air Intake
3. Bottom filter
4. Door filter
1
B
C
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.hotpoint.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identification plate.
4
2
3
xxxx
xxxxxxxxxxxx
EN
Quick guide
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
TROUBLESHOOTING
In order to receive a more complete assistance,
Beforethe
using
the appliance
carefully
thesolved
Safety
please register
product
on refer to the table below. Often
Before contacting
theyour
Service
Centre,
malfunctions
are minor
and read
can be
inInstructions.
few minutes
www.hotpoint.eu/register
Malfunction
The tumble
dryer does not
turn on.
The tumble
dryer does not
start
The drying
times are very
long
Possible cause
The plug is not inserted into the socket.
Solution
Insert the plug into the socket.
The plug is faulty.
Try to plug another appliance in the same socket. Do not use
connecting electrical devices to the socket, as adapters or extensions
A power failure occurred.
Await the reactivation of the power supply.
The door is open.
Close the door.
For machines equipped with this function: await the end of the delay
set or switch the machine off to reset it. Refer to the section Options.
A time delay for the cycle start was set.
The button Start/Pause was not pressed to start Press the button Start/Pause.
the program.
The function Key Lock was enabled (in case of
machines equipped with this option).
Refer to the option section and, if the Key Lock is present, disable it.
Switching the machine off is not enough to disable this option.
An appropriate maintenance was not carried
out.
The programme, the time and/or the drying
level set are not suitable for the type and the
amount of load inserted into the dryer.
Refer to the section Care & Maintenance and perform the operations
described.
The garments are too wet.
Carry out a washing cycle with higher spin speed to remove as much
water as possible.
Refer to the programme section to check the max. load for each
programme.
In case of power failure, it is necessary to press the button Start/Pause
to restart the cycle.
The dryer may be overloaded.
The programme A power failure occurred might have occurred.
did not end.
Lights on or flashing
Refer to the section programmes and options to find the programme
and the options most suitable for the type of load.
Water tank
The water tank is full.
Emtpy the water tank. Refer to the section Care & Maintenance.
Door filter
and/or bottom
filter*
Failure of the air flow necessary for machine
operation.
Clean the door filter and the bottom one and check whether air
intake is free. Carrying out these operations improperly may cause
damages.
Bottom filter*
The bottom filter requires cleaning.
Clean the bottom filter. Refer to section Care & Maintanence.
Disable the DEMO mode. The following actions must be carried out
in sequence, without breaks. Switch the machine on and then switch
The dryer is in DEMO mode. The DEMO
it off again. Press the Start/Pause button until the buzzer is heard.
indicator is on.
Switch the machine on again. The “DEMO” indicator flashes and then
turns off.
The presence of wrench Switch
symbolthe
signals
malfunction.
Carry
out the
described.
dryera off
and unplug
it. Open
theoperations
door immediately
and
Switch the dryer off and pull
unplug
it. Open
the
door the
immediately
and pullWait
landry
out,
to allow
laundry
out,
to
allow
heat
to
dissipate.
for
about
15
The presence
the heat to dissipate. Wait
for about
one hour.the
Reconnect
the power
dryer to
the power
supply,
load
END
minutes.
Reconnect
dryer to the
supply,
load the
laundry
of wrench
the laundry
and restart the
drying
cycle.
The
machine
sensors
detected
a
failure.
and
restart
the
drying
cycle.
If
the
problem
still
occurs,
contact
symbol signals a
the After-Sales Service Centre and communicate the letters and
180’
malfunction.
digits flashing on the display.
120’
9h
For instance: F3 and E2
DEMO
The cycle lasts
few minutes.
90’
60’
30’
6h
3h
DEMO
1h
If the problem still occurs, contact the After-Sales Service Centre and communicate the
number and the position of the flashing LEDs, starting from the bottom and the left column.
e.g.:
First, left column, LEDs No. 1 and 3 on.
Central column, LED No. 1 on.
h
*Note: some models are self-cleaning and not equipped with bottom filter. Please refer to the section Care & Maintenance.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.hotpoint.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identification plate.
W11247965
09/2018
xxxx
xxxxxxxxxxxx
">
