Whirlpool | ADG 2900 | Installation | Whirlpool ADG 2900 Installation

1Gb00079
28-11-2002
18:50
Pagina 1
I N S TA L L AT I O N I N S T R U C T I O N S
FOR PREFINISHED & INTEGRATED (SINGLE & DOUBLE) MODELS
(NOTE: FOR INTEGRATED PANEL PREPARATION INSTRUCTIONS REFER TO SUPPLIED SHEET)
DOUBLE MODELS
NOTE
1.
2.
3.
4.
TO THE INSTALLER
Read these instructions completely and carefully.
Installation of this
requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
At the completion of the
installation, the Installer must perform Final Check List as per Section 11
of these Installation Instructions.
Remove all packaging materials supplied with the
.
R
R
R
5.
NOTE TO THE CONSUMER
Keep these Installation Instructions with your User Guide for future reference.
anchored before it is operated.
R
must be securely
MODELS Prefinished Integrated
These instructions must be followed precisely to ensure correct venting and operation of the
the event of a fault related to the incorrect installation, the installer will be liable for any repairs.
SINGLE MODELS
R
. In
R
Before installing the
, remove the house fuse or open the circuit breaker. Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations.
R
The
MUST be installed to allow for future removal from the enclosure if service is required. The
installer is responsible for the
installation. Improper installation is not covered under the Warranty.
R
R
If the
is to be relocated from one installation to another it must be kept upright to avoid damage
from water spillage.
MODELS Prefinished Integrated
(page 2 of 8)
BEFORE YOU START - DOUBLE & SINGLE MODELS
PARTS SUPPLIED
DOUBLE MODELS (INTEGRATED & PREFINISHED)
INSTALLATION PREPARATION
ELECTRICAL INFORMATION
ELECTRICAL PREPARATION
A) The switched power outlet for the appliance should be
installed in a cabinet or on a wall adjacent to the under bench
space in which the appliance is to be installed. Note: The
power outlet must be accessible after installation.
B) The power outlet should be positioned between 150mm and
450mm from the
cavity.
POWER SUPPLY CORD
A) Care should be taken when the appliance is installed or
removed, to reduce the likelihood of damage to the power
supply cord.
B) If the power supply cord is damaged, it must be replaced by
the Manufacturer, Service Agent or a similarly qualified
person, in order to avoid a hazard.
PLUMBING & DRAINAGE PREPARATION
A) A readily accessible valve must be installed in the water
supply pipe.
B) If the supply pressure exceeds 1000kPa, then a pressure
limiting valve must be used.
C) Review Plumbing Options on pages 3-4. Choose a method that
best suits your needs.
EARTHING INSTRUCTIONS
A) This appliance must be earthed. In the event of malfunction
or breakdown, earthing will reduce the risk of electric shock
by providing a path of least resistance for electric current.
R
CAVITY PREPARATION
A) If installing multiple products side by side a minimum 2.5mm
clearance must be maintained around the
's.
B) On corner installations, ensure that there is a gap between
the adjacent cabinetry (e.g.door knobs) and the sides of the
open
. A 12.7mm minimum gap is recommended.
C) Where the
is installed under a bench top, it is
required that bare wood surrounding the
is
sealed with an oil based paint or polyurethane to prevent
possible steam damage. The air in the cavity can get very hot
oC)
and humid (saturated at 65
D) Ensure the cavity sides are plumb (vertical) as this will assist
with levelling the
.
E) Ensure the cavity provides sufficient material to secure the
using the mounting tabs (refer to step 1, page 5).
If there is nothing to screw to, add something. See page 3 or
4 for screw locations.
F) The services hole MUST be immediately adjacent to the rear
lower corner of the cabinetry. If not, the hoses will prevent
the
being pushed back into the cavity all the
way. The hole can be located on either side depending on the
location of the services.
R
R
R
R
SINGLE MODELS (INTEGRATED & PREFINISHED)
R
R
R
TOOLS NEEDED
Wooden Chopping Board
Tape Measure
Spirit Level
Safety Glasses
Utility Knife
Pencil
Sandpaper
Drill & No.2 Phillips Bit
No.2 Phillips Screwdriver
Flat Screwdriver
Adjustable Wrench or M5 Socket
Ø50mm Hole Saw
Side Cutting Pliers
Improper connection of the equipment-earthing conductor
can result in a risk of electric shock. Check with a qualified
electrician or service representative if you are in doubt as to
whether the appliance is properly earthed.
B) This appliance is equipped with a power supply cord having
an equipment-earthing conductor and an earthing plug. The
power supply plug must be plugged into an appropriate
outlet that is installed and earthed in accordance with all
local Codes and Regulations.
Do not modify the power supply plug provided with the
appliance - if it will not fit the outlet, have a proper outlet
installed by a qualified electrician. Do not use an extension
cord, adaptor plug or multiple outlet box.
1Gb00079
28-11-2002
18:50
Pagina 2
(page 3 of 8)
DOUBLE MODEL
SERVICE'S SPECIFICATION
PLUMBING OPTIONS
THE CAVITY
Option 1
*
Min thickness of cavity
sides is 16mm
82.5mm
+
90°
R
and Standpipe Ø38mm with Air Gap.
14mm
From front
of cabinetry
+
640.5mm
#
Water Softener Models
Refer to your
softener.
R
50
5m
m
Water Connection
Recommended COLD (Maximum 60°C).
3/4 " BSP (GB20) to suit flat washer.
820mm-880mm
R
*For an Integrated
the product depth is specified with an
18mm Integrated Door Panel thickness.
R
Option 2
with Waste Disposal.
Standpipe Ø38mm with Air Gap.
Ø50mm
services hol
can be either
+
side, immediatel
adjacent to
corner
+
e
y
+
+
97mm
User Guide on how to set up your water
580mm
throughout cavity
Water Pressure
Water Softener Models
Other Models
Maximum
1000kPa (145 p.s.i.)
1000kPa (145 p.s.i.)
Minimum
100kPa (14.5 p.s.i.)
30kPa (4.3 p.s.i.)
Drain Connection
Drain Hose Joiner to suit
Ø19mm ± 2mm waste tee.
600mm
R
PLEASE NOTE: It is NOT recommended to connect the
to any part of the Waste Disposal System.
+
These marks indicate
mounting tab
crew locations (refer to step 1 page 5)
Option 3
Electrical Connection
230-240 VAC power outlet
9Amps Minimum.
R
using Sink Trap with Drain Hose Joiner.
Toe Kick Depth
Prefinished 50-65mm; Integrated 67mm less the Toe Kick Panel
thickness (Minimum Panel thickness using the supplied screws is 9mm).
# Door Front Height
Prefinished 717.5mm; Integrated 717.5mm minimum.
Length of Services
Drain hose - 2250mm
Inlet hose - 1750mm
Power supply cord - 1965mm
NOTE: Services approximately exit product
189mm from left; 550mm from front; 793mm from top.
NOTE: All depth measurements are taken from the front
face of the adjacent cabinetry.
Ensure the edges of the services hole are smooth or
covered.
NOTE: Prefinished Model is shown. There is no variation in plumbing
between Prefinished products and Integrated products. Option 1
and 2 are the preferred options. Options 1 & 2 or use of a Dual Inlet
Airgap satisfy Kosher requirements.
(page 4 of 8)
SINGLE MODEL
PLUMBING OPTIONS
THE CAVITY
SERVICE'S SPECIFICATION
Option 1
and Standpipe Ø38mm with Air Gap.
Ø50mm services hole can be either side,
immediately adjacent to corner
*
410mm
90°
505
Min thickness
of cavity
sides is 16mm
mm
+
+
97mm +
+
580mm
throughout cavity
67mm
*For an Integrated the product depth is specified with an 18mm
Integrated Door Panel thickness.
600mm
Option 2
with Waste Disposal.
Standpipe Ø38mm with Air Gap.
Water Connection
Recommended COLD (Maximum 60°C).
3/4 " BSP (GB20) to suit flat washer.
Water Softener Models
Refer to your
softener.
User Guide on how to set up your water
+
These marks indicate mounting tab
screw locations (refer to step 1 page 5)
Water Pressure
Water Softener Models
Other Models
Maximum
1000kPa (145 p.s.i.)
1000kPa (145 p.s.i.)
Drain Connection
Drain Hose Joiner to suit
Ø19mm ± 2mm waste tee.
Electrical Connection
230-240 VAC power outlet
4.5Amps Minimum.
Weight
Full 42kg Prefinished
Empty 28kg Prefinished
Length of Services
Drain hose - 2250mm
Inlet hose - 1750mm
Power supply cord - 1965mm
NOTE: Services approximately exit product
189mm from left; 550mm from front;
393mm from top.
Minimum
100kPa (14.5 p.s.i.)
30kPa (4.3 p.s.i.)
NOTE: All depth measurements are taken from the front
face of the adjacent cabinetry.
NOTE: To align drawer front to adjacent cabinetry, the
product to counter top clearance can be increased
from 3mm.
PLEASE NOTE: It is NOT recommended to connect the
to any part of the Waste Disposal System.
Option 3
using Sink Trap with Drain Hose Joiner.
Ensure the edges of the services hole are smooth or covered.
Cabinetry must
not extend beyond
cavity base
NOTE: Prefinished Model is shown. There is no variation in plumbing
between Prefinished products and Integrated products. Option 1 and
2 are the preferred options. Options 1 & 2 or use of a Dual Inlet
Airgap satisfy Kosher requirements.
1Gb00079
28-11-2002
18:50
Pagina 3
READ THESE INSTRUCTIONS
COMPLETELY AND CAREFULLY.
INSTALLATION INSTRUCTIONS
(page 5 of 8)
R
PLEASE NOTE: Your model of
may differ from the model shown in the installation diagrams. Installation is similar for Integrated & Prefinished products for either Single or Double models.
Information referring to Single models only is highlighted in blue. Installation diagrams have been simplified to enable clearer instruction. FOR INTEGRATED PRODUCTS FOLLOW THE INTEGRATED PANEL PREPARATION
INSTRUCTIONS, BEFORE MOVING THE PRODUCT INTO THE CAVITY.
1 MOVING THE PRODUCT INTO THE CAVITY
2 REMOVING THE TUB
3
ADJUSTING THE FEET
DOUBLE MODELS ONLY
R
must be free to close completely.
With overlapping integrated drawer fronts
a 2.5mm clearance must be maintained
between drawer front and cabinetry.
1
4
6
The product should NOT support
any part of the kitchen cabinetry.
3
Be careful of
sharp edges.
8
MOUNTING TAB OPTIONS
The mounting tabs are in pairs, one on each side of the product. They
are used to secure the product to the cavity sides. Installation requires
two sets of tab pairs be used, for example A and B tab pairs. All tabs
would be optimum. A minimum installation requires that the B
mounting tabs be used.
9
7
4
DOUBLE MODELS ONLY C Mounting Tab Option
If the top installation tabs C are to be used, fit to the chassis by
inserting into the top slots as shown. Ensure the tabs are fully
locked in place.
SINGLE MODELS ONLY. Gently open the drawer and mark
the chassis position on the cavity, before removing the
tub.
5
Open the drawer (Bottom drawer in DOUBLE MODELS).
Release the tub by depressing the right hand tub clip and
pushing it back 30mm. Repeat on the left hand side.
2
Check cavity for any obstructions that may interfere with sliding the
product back. Loosen the feet DOUBLE MODELS ONLY.
6
Lift the tub up off the drawer runners.
Push product into cavity to suit adjacent cabinetry. Do not push
middle of drawer(s). Ensure inlet, drain hose(s) and power supply
cord are not restricted or damaged by carefully pulling them
through the services hole, while the product is being pushed back
into the cavity.
7
Slide both runners back into the product.
3
8
Place the tub onto the floor.
For SINGLE MODELS, depending on the height of the
cavity, the tub will need to be supported, eg. on a chair.
1
4
MINIMUM CLEARANCE TO
UNDERSIDE OF COUNTER 2.5mm
5
2
DO NOT push
middle of
drawers.
(SINGLE MODELS ONLY). The product
may move. Mark chassis position on
cavity.
SECURING THE PRODUCT
5
REFITTING THE TUB
6
10
DOUBLE MODELS ONLY
Adjust the height of the product to suit the cabinetry, by
turning the feet from inside the product using a wrench or
M5 socket. TIP - gently take the load off each foot using
the slide and then turn by hand.
NOTE: For integrated products, align the top of the
upper panel with the top of the adjacent cabinetry.
The product must be levelled to within 2.5mm from
front to back, and side to side. TIP - Place a spirit level
on the drawer runners to level the product.
(page 6 of 8)
CONNECTING THE DRAIN HOSE(S)
R
Before refitting the tub, ensure the hoses are not
twisted and the latches at the rear of each drawer
runner are facing forward.
9
with Hose Joiner (see Plumbing Options).
Remember to slip the wire clip(s) on the drain hose(s) first.
The Drain Hose
support must be
used.
15a
Ensure the Drain
Hose(s) are fully
extended.
11
12
13
NOTE - SINGLE MODELS do
not have top tabs.
Drain Hose joiner
MUST NOT support weight of
hoses. Keep
excess length of
Drain Hose on the
side
of the Drain Hose
support.
R
14
10
SINGLE MODELS ONLY
Check the position of the chassis is still where
marked on the cavity, before securing the
product.
11
There are four 16mm round holes, two on the
left and right hand side of the sound
insulation. To secure the product to the
cabinetry use a 16mm Phillips screw in each
hole.
12
DOUBLE MODELS ONLY
Screw the two top tabs to the underside of
bench. Use the supplied Phillips 16mm screws.
Tabs can accommodate a maximum of 19mm
vertical gap.
16
15b
Minimum hole size
to be connected
to the drain system is 16mm.
Ensure the tub clips on both sides are reset.
13
While the tub is removed, it can be rotated or
turned upside down. This will cause the hoses to
become twisted. Reverse the direction to unwind
the hoses before refitting the tub.
14
To refit the tub, make sure both of the latches at
the rear of each drawer runner are facing forward.
Ensure hoses are hooping upward. Place the tub on
the half open drawer runners and close the drawer.
Check the tub clips have reset on both sides of the
tub. If not, pull the tub clips forward until the tub
clip button is reset.
15a
Slip a wire clip over each drain hose, then push the hoses into the Drain Hose
Joiner firmly, 5 clicks. Position the wire clip(s) between the two positioning ribs
on the Drain Hose Joiner.
15b
Attach the Drain Hose Joiner to the waste tee (see Plumbing Options). Ensure a
snug fit. If required a hose clamp may be used.
16
When using the standpipe option (see Plumbing Options), hose(s) should not
extend further than 120mm down the standpipe, in order to prevent siphoning.
Attach the Drain Hose Support to the cabinetry (with the screw supplied) to
prevent siphoning and to keep the drain hose(s) from kinking. If required, the
Drain Hose(s) may be trimmed to a suitable length.
1Gb00079
7
28-11-2002
18:50
Pagina 4
CONNECTING THE INLET HOSE & POWER SUPPLY
8
MEASURING THE TOE KICK
9
(page 7 of 8)
TRIMMING THE TOE KICK
DOUBLE MODELS ONLY
DOUBLE MODELS ONLY
IMPORTANT - Before cutting ensure the Toe Kick is positioned on a
wooden chopping board to avoid damage to surrounding area.
DO NOT plug the product in at this stage.
20
18
21
17
19
Remove all sharp edges
DO NOT cut the inlet hose.
22
17
18
Connect the Inlet Hose to the water supply. Ensure the sealing
washer is in place. The hose coupling must be tightened a further
half turn after seal contact. TIP - Turn the water valve ON to check
for any leaks.
Bottom edge
of tub side
Ensure there is a power outlet in reach of the power supply cord. If
there is not a suitable outlet available then have one installed by a
qualified electrician.
19
Partially open the bottom drawer. Turn
Prefinished Toe Kick upside down and hold
vertically against the bottom edge of the
Tub side (not the drawer front).
Mark the position of the bottom edge of the
Tub side on the Toe Kick.
NOTE: SINGLE MODELS DO NOT HAVE A TOE KICK TO INSTALL.
PROCEED TO STEP 11 FINAL CHECK LIST.
Choose the nearest groove to the pencil mark
which will result in the shortest Toe Kick.
10 FITTING TOE KICK TO PRODUCT
DOUBLE MODELS ONLY
20
On the chosen groove cut down the vertical ribs at the centre and
the ends using a knife. Cut along full length with a knife. Turn Toe
Kick over, bend and then cut from front. Sand or scrap bottom edge
to remove rough patches.
21
To avoid a cutting hazard remove all sharp edges after trimming.
22
Remove Toe Kick tabs by snapping them off.
(page 8 of 8)
11 FINAL CHECK LIST - DOUBLE & SINGLE MODELS
Ensure product is level, securely fastened to the cabinetry and opens and closes
freely. The
must be free to close with no resistance from the
cabinetry.
R
Ensure inlet hose to valve connection is tightened a further half turn after seal
contact.
Ensure any knockouts or plugs in drain connection have been drilled out and
drain connection has been made.
TROUBLE SHOOTING
Excessive water remaining above the filter plate,
after the rinse cycle; check for kinked drain hoses or
blocked waste connection.
No water supply; check water is connected, ON and
there is water pressure.
R
Turn ON the power and water supply.
The
should beep and light up.
R
23
Open the drawer(s) and check operation of Wash Programme Control Panel and
check the sprayarm(s) are in place and free to rotate.
On the Wash Programme Control Panel select Rinse and close the drawer(s). Start
the programme by pressing the Start/Pause button.
After the Rinse programme has finished, ensure machine has run and drained
correctly.
24
Check water supply and drainage connection for leakage.
does not light up when the tub is
opened; ensure power is connected and is switched
ON.
Water around water supply and drainage connections
- check connections, existing plumbing and hoses for
leaks.
If a fault occurs, consult the Fault Code Section of
the User Guide.
If unable to resolve, contact your Customer Care
Centre.
Repeat for each Drawer.
LEAVE ALL LITERATURE WITH CUSTOMER.
DO NOT over tighten screws.
Overtightening will damage
the plastic mounting detail.
12 CUSTOMER SUPPORT
23
Partly open bottom drawer. Position Toe Kick
behind door and slide onto the mounting rails on
the underside of tub.
If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the
24
Close bottom drawer, check if flush with adjacent
cabinetry. If required open drawer and adjust.
Note: Clearance between Toe kick and floor must
be 12mm minimum.
Before contacting our After-Sales Service, take note of the following:
When Toe Kick is in position, open bottom drawer
and gently fasten the Toe Kick screws, on each
side.
water supply tap, then call our After-Sales Service (see guarantee).
• The nature of the fault.
• The appliance type and model.
• The service code (the number indicated on the adhesive rating plate).
Whirlpool is a registered trademark of Whirlpool USA
5019 102 00079
Download PDF

advertising