KitchenAid | KHIP4 77510 | Instruction for Use | KitchenAid KHIP4 77510 Instruction for Use

Instructions for use
Installation diagrams
4
Important safety instructions
6
Safeguarding the environment
9
Eco Design Declaration
9
Before use
9
Using existing pots and pans
10
Recommended pan base diameters
10
Installation10
Electrical connection
11
Instructions for use 12
Cleaning16
Troubleshooting guide
16
After-Sales Service
17
Power level table
18
Functions table
19
Cooking table
20
Installation diagrams
280 mm
180 mm
180 mm
145 mm
Min. 5 cm
Min. 10 cm
Min. 3 cm
Max. 6 cm
R = Min. 6,5 mm
Max. 8 mm
0
750 +2 mm
Min. 50 mm
0
490 +2
mm
0
R = 11,5 mm
773 +2 mm
Min. 50 mm
0
0
513 +2 mm
0
750+2
490+2 mm
mm
R = 11,5 mm
R = Min. 6,5 mm
Max. 8 mm
6 mm
4
Installation diagrams
5 mm
5
These instructions are also available on our website: docs.kitchenaid.eu IMPORTANT SAFETY INSTRUCTIONS
SAFETY IS OUR PRIORITY
This manual and the appliance itself display important safety
messages, which must be read and then observed at all times.
This is the danger symbol, regarding safety, warning of potential
risks to users and others.
All safety messages are preceded by the danger symbol and the
text shown here:
DANGER
Indicates a hazardous situation which, if not
avoided, will result in serious injury.
WARNING
Indicates a hazardous situation which, if not
avoided, could cause serious injury.
All messages relevant to safety specify the potential risk to which they
refer and indicate how to reduce the risk of injury, damage and electric
shock due to incorrect use of the appliance.
Ensure that everyone complies with the following:
-- U
se protective gloves when unpacking and installing.
-- The appliance must remain disconnected from the power supply
before any installation operation is carried out.
-- Installation and maintenance must be carried out by a specialised
technician, in compliance with the manufacturer’s instructions and
the local safety regulations in force. Do not repair or replace any part
of the appliance unless specifically stated in the user manual.
-- The appliance must be earthed.
-- The power cable must be long enough for connecting the appliance
(fitted inside the cabinet) to the power supply.
-- For installation to comply with the current safety regulations, an
omnipolar switch with minimum contact gap of 3 mm is required.
-- Do not use multi-sockets or extension cords.
6
-- Do not pull the appliance’s power cable.
-- The electrical parts must not be accessible to the user after
installation.
-- The appliance is designed solely for domestic use, for cooking food.
No other use is permitted (e.g. heating rooms). The manufacturer
declines any liability for inappropriate use or incorrect setting of the
controls.
-- The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Very young
(0-3 years) and young children (3-8 years) must be kept away unless
continuously supervised.
-- Children aged 8 years and above, and persons with reduced
physical, sensory or mental capabilities or lack of experience and
knowledge can only use this appliance if they are supervised or
have been given instructions on safe appliance use, and if they
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be carried out
by children without supervision.
-- Do not touch the appliance heating elements during or after use. Do
not allow the appliance to come into contact with cloths or other
flammable materials until all the components have cooled down
completely.
-- Do not place flammable materials on or near the appliance.
-- Overheated oils and fats catch fire easily. Pay attention when
cooking food products rich in fat and oil.
-- A separator panel (not supplied) must be installed in the
compartment under the appliance.
-- If the surface is cracked, switch off the appliance to avoid the
possibility of electric shock. (Only for appliances with glass surface.)
-- The appliance is not intended to be operated by means of an
external timer or separate remote control system.
-- Unattended cooking on a hob with fat or oil can be dangerous and
may result in fire. NEVER try to extinguish a fire with water, but
switch off the appliance and then cover the flame with a lid or a fire
blanket, for example.
Danger of fire: do not store items on cooking surfaces.
-- Do not use steam cleaners.
7
-- Metallic objects such as knives, forks, spoons and lids should not be
placed on the hob surface since they can become hot.
-- After use, switch off the hob element at its control, and do not rely
on the pan detector (Only for appliances with glass surface).
Disposal of household appliances
---
This product is built from recyclable or reusable materials. Disposal must be carried out in accordance
with local regulations for waste disposal. Before scrapping, cut off the power supply cable.
For further information on the treatment, recovery and recycling of household appliances, contact the
competent local authority, the domestic waste collection service or the shop where you purchased the
product.
8
Safeguarding the environment
Disposal of packaging materials
Energy saving tips
The packaging material is entirely recyclable and
marked with the recycling symbol ( ). Do not
dispose of the various packaging materials
carelessly, but do so responsibly and in full
compliance with local authority regulations
governing waste disposal.
For optimum results, observe the following advice:
• Use pots and pans whose bottom diameter is
equal to that of the cooking zone.
• Only use flat-bottomed pots and pans.
• If possible, keep pot lids on while cooking
(except for use in “SENSOR” mode).
• Cook vegetables, potatoes, etc. with little water
in order to reduce cooking time.
• Use a pressure cooker to save even more
energy and time (except for use in “SENSOR”
mode).
• Make sure you place the pot or pan in the
centre of the cooking zone outlined on the hob
Scrapping
This appliance is marked in compliance with
European Directive 2012/12/EU on Waste Electrical
and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health.
The symbol on the appliance or accompanying
documentation indicates that this product should
not be disposed of as unsorted municipal waste
but must be taken to a collection point for the
treatment of WEEE.
Eco Design Declaration
This appliance meets the eco design requirements of European regulation N. 66/2014, in conformity with
European standard EN 60350-2.
Before use
IMPORTANT: the cooking zones will not switch on if pots and pans are not of
the correct dimensions. Only use pots bearing the “INDUCTION SYSTEM”
symbol (see figure opposite). Before switching the hob on, position the pot on
the desired cooking zone.
9
Using existing pots and pans
Use a magnet to check whether pots or pans are suitable for use on the induction hob: pots are unsuitable
if they cannot be magnetically detected.
-- Ensure pots have a smooth bottom, otherwise they may scratch the hob’s glass ceramic surface. Check
dishes.
-- Never place hot pots or pans on the hob’s control panel. This could result in damage.
OK
NO
Recommended pan base diameters
XL
Ø 30 cm
Ø 14 cm
30 cm
XL
Ø 28 cm
Ø 18 cm
28 cm
L
Ø 24 cm
Ø 17 cm
24 cm
L
Ø 21 cm
Ø 15 cm
21 cm
M
Ø 18 cm
Ø 14 cm
18 cm
S
Ø 14.5 cm
Ø 11 cm
14.5 cm
IMPORTANT: Refer to the “SENSOR” section for information on the correct pan base diameters for cooking
zones with the SENSOR function. If adapter plates (not provided) are used or a pan is empty, the internal
temperature of the system will exceed the set limit and the power supply to the hob will be switched off.
This happens to protect the internal components from overloading. We recommend switching off the hob
and allowing the cooking zone to cool down to the temperature at which the indicators on the control
panel switch off.
After unpacking the hob, check that there has been no damage during
transport. If in doubt, contact the dealer or After-Sales Service.
PREPARING THE HOUSING UNIT
min 5 mm
Installation
min 20 mm
WARNING
---•
•
•
•
•
•
Install a separator panel under the hob.
The lower part of the product must not be accessible after
installation.
If there is an oven beneath the hob, do not install the separator panel.
min 5 mm
For the distance between the underside of the appliance and the separator panel below, observe the
dimensions given in the figure.
To ensure correct operation of the product, do not obstruct the minimum required clearance between
the hob and the top of the unit.
Cut the worktop to fit before installing the hob and carefully remove any shavings or sawdust.
If there is an oven beneath the hob, check that it has a cooling system.
For flush-mounting, call the After-Sales Service to fit screw kit 4801 211 00112 supplied with the
product.
Do not install the hob over a dishwasher or washing machine as the electronic circuits could be
damaged by steam and humidity.
10
Electrical connection
WARNING
-------
Disconnect the appliance from the mains power supply.
Installation must be carried out by a qualified electrician who is fully aware of current safety and
installation regulations.
The manufacturer shall not be held liable for injury to persons or animals, or for damage to
property resulting from failure to observe the regulations provided in this chapter.
The power supply cable must be long enough to allow the hob to be removed from the worktop.
Ensure that the voltage specified on the appliance rating plate is the same as that of the house
electrical system.
Do not use extension leads.
Connecting to the terminal board
Use an H05RR-F cable (as indicated in the table below) for the electrical connection.
4 x 1.5 mm²
A
B
C
380-415 V 2N ~
220-240 V 3 ~
(Belgium only)
230 V
380-415 V 2 N ~ +
230 V
5 x 1.5 mm²
220-240 V ~
(AU and UK)
230 V
380-415 V 3 N ~ +
230 V
5 x 1.5 mm²
230 V
220-240 V 3 ~ +
230 V
3 x 4 mm²
220-240 V ~
230 V
230 V
230 V
220-240 V ~ +
380-415 V 3 N ~
230 V
Amount x size
230 V
Conductors
380-415 V 2N ~
(NL only)
Connect the yellow/green earth wire to the terminal with the symbol
.
This wire must be longer than the other wires.
1. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block
hinge (B).
2. Strip approx. 70 mm of sheath from the power supply cable.
3. Strip approx. 10 mm of sheath from the wires. Insert the power supply cable into the cable clamp and
connect the wires to the terminal board (as indicated in the diagram) next to the terminal board itself.
4. Secure the power cable with the cable clamp.
5. Close the cover (C) and screw it on the terminal block with the removed screw – point (1).
Each time the hob is connected to the mains it carries out an automatic check which lasts several seconds.
If the hob already has a power cable, follow the instructions on the instruction label attached to the cable.
Connect the appliance to the mains electricity supply using a multipole switch disconnector with
minimum contact gap of 3 mm.
11
Instructions for use
Control panel description
The control panel is equipped with touch controls: to use them, just press the corresponding symbol (a
light touch is sufficient).
To switch the single cooking zone OFF
Switching
the hob
ON/OFF
To select and
activate the
cooking zones
To set the
minute minder
To select one of the
automatic functions
Slide touchscreen
To activate the
flexible zone
function
To enable the
hold function
To lock the
control panel
First use / after a power failure
After connecting the hob to the electrical power supply, the control panel is locked (the indicator light
above the key is ON).
To unlock the control panel, press and hold the key for 3 seconds. The indicator light switches off and
the hob can be used normally.
Switching the hob ON/OFF
To switch the hob on, press and hold down the
key for about 2 seconds: the indicator light above the
key turns on and hyphens appear inside the cooking zone circles.
To switch off, press the same key until the hob switches off. All the cooking zones are deactivated.
Switching the single cooking zone OFF
To switch OFF the single cooking zone, press the
corresponding button.
i The hob automatically switches off if no function is selected within 10 seconds of switching on.
Activating and adjusting cooking zones
Cooking zone timer
55
Cooking zone selection and selected cooking
zone/power level display
0
Slide touchscreen (power adjustment)
After switching the hob on, position a pot on the required cooking zone.
Activate the cooking zone by pressing the relative round key: the round key displays number 0, which
corresponds to the intermediate power level.
12
Instructions for use
If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions
for your induction hob, the message “no pot” will appear in the display (see figure on the left). If no pot is
detected within 60 seconds, the hob switches off.
0. To change the power level, move your finger horizontally on the slide touchscreen: the number inside
the circle will change with just a quick slide of the finger from a minimum of 1 to a maximum of 9. You can
activate the booster function by pressing “BOOST” on the slide touchscreen (“P” on the display). The
“BOOST” power level can be used for up to 10 minutes, after which the appliance automatically switches to
level 9. If more than one cooking zone is on, the slide touchscreen allows you to change the power level of
the selected zone, indicated by the presence of a luminous dot at the bottom right of the power level
indicator. To select a zone, simply press the corresponding round key.
Deactivating cooking zones
Select the cooking zone to be switched off by pressing the corresponding round key (a dot lights up at the
bottom right of the power level indicator). Press OFF on the slide touchscreen.
The cooking zone switches off and, if the zone is still hot, the letter “H” appears in the circle.
“H” is the residual heat indicator. The hob has a residual heat indicator for each cooking zone; these
indicators alert the user when cooking zones are still hot. When the cooking zone cools down, the display
switches off.
Timer selection
The timer can be used to set a max. cooking time of 90 minutes.
Select the cooking zone to be used with the timer (a luminous dot appears at the bottom right of the
power level indicator on the display), then set the required time using the + and - keys of the timer
function: the time in minutes is shown next to the cooking zone display.
A few seconds after the last press, the timer begins the countdown (the cooking zone selection dot starts
flashing).
Once the set time has elapsed, an acoustic signal sounds and the cooking zone switches off automatically.
For the timer associated with the SENSOR function, refer to the description of the function on the
following pages.
Control panel lock
This function locks the hob controls to prevent accidental activation (e.g. during cleaning).
Press the : key for three seconds: an acoustic signal sounds and an indicator light turns on above the
lock symbol to confirm activation. The control panel is locked with the exception of the OFF function. To
unlock the controls, repeat the activation procedure. The luminous dot goes off and the hob is active
again.
IMPORTANT: The presence of water, liquid spilled from pots or any objects resting on the key below the
symbol can accidentally activate or deactivate the control panel Lock function.
Hold
This function allows you to temporarily hold and then resume cooking processes maintaining previous
settings (except for SENSOR function and timer setting). Press the
key:
blinks on the display in
place of the power levels.
To resume cooking, press the
key again.
13
Instructions for use
Flexible zone
This function allows you to use two cooking zones as an extra-large single zone. It is perfect for oval,
rectangular and elongated pans (with maximum base dimensions of 40x18 cm). After switching on the
hob, press the
key: the two cooking zone displays show level “0”; both dots next to the level number
are lit, indicating selection as a single cooking zone. To change the power level, slide your finger on the
touchscreen: the number inside the circle will change with just a quick slide of the finger from a minimum
of 1 to a maximum of 9. To deactivate the flexible zone function, press the
key: the plates resume
operation as two separate cooking zones. To switch off the cooking zone, press OFF.
i The booster power level and SENSOR function cannot be used when the flexible zone function is in
use. If you use the timer, the time will appear next to the display of the highest plate.
Description of automatic functions
The hob features automatic functions for each cooking zone. The symbols of the available functions are
shown next to the selection key of each cooking zone. Every time an automatic function is selected, an
indicator light turns on next to the symbol and the letter “A” appears in the cooking zone display.
SENSOR
The SENSOR function automatically selects the ideal power level to bring water to the boil, and signals
boiling point.
After positioning the pot containing water on the zone displaying the word SENSOR, switch on the hob
and select the zone. Press the
key: “A” appears on the display and the indicator light turns on. An
animation is displayed in the space next to the zone as it heats up.
i To ensure correct operation of the SENSOR function, we recommend that you:
-- use water only (at ambient temperature);
-- do not add salt, ingredients or seasoning (until boiling point);
-- do not change the zone’s power level, remove or move the pot;
-- use pots and pans with base diameter between 24 and 28 cm;
-- fill the pot to at least 1/3 full (about 1 litre) and never to the brim (max. 7 litres);
-- do not use pressure cookers.
For optimum results, please also observe the following advice:
-- do not put the lid on the pot that is being used with the SENSOR function;
-- do not activate the SENSOR function if the zone is still hot (letter “H” on the display).
When the boiling point is reached, the hob emits an acoustic signal. The acoustic signal sounds three
times at regular intervals. After the second signal, a minute counter automatically begins counting the
boiling time. After the third signal, the hob automatically selects a lower power level suitable for
maintaining the boil. From this moment you can add the ingredients, set the timer or change the power
level.
Changing the power level or activating the hold function deactivates the SENSOR function.
-- The hob manages the SENSOR function and booster levels autonomously, therefore, in some cases, it
may not be possible to activate the booster with the SENSOR function already in use;
-- the quality of the cookware may affect the performance of the SENSOR function.
Multifunction key
This key allows you to select the “Simmer”, “Melt” or “Keep warm” function along with a specific cooking
zone.
After selecting the zone, press the
key; the indicator light near the special function symbols next to
each cooking zone indicates the automatic function selected. Press the
key repeatedly to set the
required function.
14
Instructions for use
Simmer
Bring the food to the boil, then press the relative key to select the simmering function;
an appropriate
power level will be set automatically to keep it just under the boil. To deactivate the function, simply press
OFF on the slide touchscreen.
Melt
This function maintains a permanently low temperature in the cooking zone. After positioning the pot/
accessory on the chosen cooking zone, switch on the hob and select the cooking zone. Press the
key
repeatedly to select the function. To deactivate the function, simply press OFF on the slide touchscreen.
Keep warm
Identifies a power level that is suitable for keeping meals warm. After positioning the pot/accessory on the
chosen cooking zone, switch on the hob and select the cooking zone. Press the
key repeatedly to
select the function. To deactivate the function, simply press OFF on the slide touchscreen.
GRIDDLE
This function allows you to grill various types of food using the specific accessory.
i Only use the accessory supplied.
The use of any other accessory may compromise the performance of the function.
Position the accessory on the cooking zone displaying the word “GRIDDLE”. Press the
key. An indicator
light turns on above the key and the letter “A” appears simultaneously on the display.
When the hob has almost finished heating the accessory, a beep will sound three times, once every 30
seconds. You can now put the food in the pot. At the second beep, a minute counter starts to measure the
time that the accessory has been at the ideal temperature for.
i When the GRIDDLE function is in use, the “flexible zone” and “booster” functions cannot be activated
on the same cooking zone.
15
Cleaning
WARNING
---
Never use steam cleaners.
Before cleaning, ensure that the cooking zones are switched off and that the residual heat
indicator (“H”) is not displayed.
IMPORTANT: do not use abrasive sponges or pan scourers as they could ruin the glass surface.
• After each use, clean the hob once it has cooled in order to remove any food residues.
• Sugar and foods with a high sugar content damage the glass ceramic surface and must be
immediately removed.
• Salt, sugar and sand can scratch the glass surface.
• Use a soft cloth, absorbent kitchen wipes or a specialist hob cleaner (see the manufacturer’s
instructions).
Troubleshooting guide
•
•
•
•
•
Read and follow the instructions given in the section “Instructions for use”.
Connect the hob to the electricity supply and check that the supply has not been shut off.
Clean the hob and dry it thoroughly.
If you are unable to turn the hob off after using it, disconnect it from the power supply.
If alphanumeric codes appear on the display when the hob is switched on, consult the following table
for instructions.
ERROR CODE
DESCRIPTION
POSSIBLE CAUSES
REMEDY
The hob switches off,
and after 30 seconds
emits an acoustic
signal every
10 seconds.
Continuous pressure
on control panel area.
Water or utensils on
control panel.
Clean the control
panel.
C81, C82, C83
The control panel
switches off because of
excessively high
temperatures.
The internal
temperature of
electronic parts is too
high.
Wait for the hob to cool
down before using it
again.
F42 or F43
The connection
voltage is wrong.
The sensor detects a
discrepancy between
the appliance voltage
and that of the mains
supply.
Disconnect the hob
from the mains and
check the electrical
connection.
F12, F21, F25, F36, F37,
F40, F47, F56, F58, F60,
F61, F62, F63, F64
Call the After-Sales Service and specify the error code.
16
After-Sales Service
Before contacting the After-Sales Service
1. See whether you can eliminate the problem on your own by referring to the “Troubleshooting guide”.
2. Turn the hob off and on again, and check whether the problem has been eliminated.
If the fault persists after the above checks, contact the nearest After-Sales Service.
Always specify:
• a brief description of the fault;
• the type of product and exact model;
• the Service number (the number after the word “Service” on the rating plate), located under the
appliance (on the metal plate). The Service number is also given in the warranty booklet;
• your full address;
• your telephone number (including area code)..
If any repairs are required, contact an authorised After-Sales Service Centre (to ensure the use of
original replacement parts and correct repairs). Replacement parts will be available for 10 years.
17
Power level table
Type of cooking
Used for
(indicating cooking experience and habits)
Boost
For heating quickly
Ideal for rapidly increasing the temperature to
fast boiling in the case of water, or rapidly
heating cooking liquids.
8-9
Fry/boil
Ideal for browning, starting to cook, frying
deep frozen products, fast boiling.
7-8
For browning –
sautéing – boiling –
grilling
Ideal for sautéing, maintaining a fast boil,
cooking and grilling (for a short period of time,
5-10 minutes).
6-7
For browning – cooking
– stewing
sauté – grill
Ideal for sautéing, maintaining a light boil,
cooking and grilling (for a medium period of
time, 10-20 minutes), preheating.
4-5
Cook/stew
sauté – grill
Ideal for stewing, maintaining a gentle boil,
cooking and grilling (for a long period of time).
Power level
Max.
power
High power
3-4
Medium
power
Cook/simmer/thicken/
cream pasta
2-3
Ideal for long-cooking recipes (quantities
under 1 litre: rice, sauces, roasts, fish) with
liquids (e.g. water, wine, broth, milk).
1-2
Melt/defrost
Ideal for softening butter, gently melting
chocolate; defrosting small products.
1
Keep food warm
Cream risotto
Ideal for keeping small portions of just-cooked
food or serving dishes warm and for creaming
risotto.
Zero
power
Support surface
Hob in stand-by or off mode (possible end-ofcooking residual heat, indicated by an “H”).
Low
power
OFF
Ideal for long-cooking recipes (rice, sauces,
roasts, fish) with liquids (e.g. water, wine, broth,
milk), creaming pasta.
18
Functions table
Function
Description of automatic functions
Simmer
Identifies a power level that is suitable for simmering long-cooking
recipes. Suitable for cooking tomato sauce, ragù, soups, minestrone,
maintaining a constant cooking level; ideal for cooking in a bainmarie (creams) and regenerating cooked food. Prevents food from
boiling over or sticking to the bottom and burning, as often happens
with these recipes. Use this function after bringing the food to the
boil.
Melt
Identifies a power level that is suitable for slowly melting delicate
products without impairing quality (chocolate, butter, etc.).
KEEP WARM
Identifies a power level that is suitable for keeping meals or serving
dishes warm.
Sensor
Automatically senses when the water reaches boiling point and
reduces the power to maintain the boil until the food is added. When
the water reaches boiling point, an acoustic signal indicates when
you can add the desired ingredients (e.g. seasoning, pasta, rice,
vegetables, meat and fish), but also homemade preserves or
accessories to be sterilised.
Flexible zone
This function combines two cooking zones to offer an extra-large
cooking surface for rectangular and oval containers or grilling pans.
To grill large or many food items (fish, kebabs, vegetables, steaks,
sausages).
For cooking recipes with liquids or broth such as roulades and whole
fish in casseroles/fish kettles/pans.
Griddle
Designed to be used exclusively with the accessory supplied. This
function automatically identifies a power level that is ideal for grilling
various types of food.
Wait until the function signals that the accessory is preheated, then
place food on it. The accessory supplied provides uniform heat
distribution that ensures perfect grilling of any type of food (meat,
fish, vegetables); e.g. kebabs, steaks, hamburgers, slices of fish,
würstels, cheese, vegetables.
19
Cooking table
Food
categories
Dishes or type
of cooking
Power level and cooking stage
First stage
Power
Second stage
Power
Fresh pasta
Heating the water
Booster
–9
Cooking the pasta and
maintaining the boil
7-8
Dry pasta
Heating the water
Booster
–9
Cooking the pasta and
maintaining the boil
7-8
Boiled rice
Heating the water
Booster
–9
Cooking the rice and
maintaining the boil
5-6
Risotto
Sautéing and frying
7-8
Maintaining the right
cooking temperature
4-5
Boiled
Heating the water
Booster
–9
Cooking
6-7
Fried
Heating the oil
9
Frying
8-9
Sautéed
Heating the accessory
7-8
Cooking the food
6-7
Stewed
Heating the accessory
7-8
Cooking and
maintaining the
temperature
3-4
Browned
Heating the accessory
7-8
Browning the soffritto
7-8
Roast
Browning the meat
with oil (if with butter:
power level 6)
7-8
Cooking
3-4
Grilled
Preheating the grill
7-8
Grilling on both sides
7-8
Browned
Browning with oil (if
with butter: power
level 6)
7-8
Cooking
4-5
Stewed
Browning with oil (if
with butter: power
level 6)
7-8
Cooking and
maintaining the
temperature
3-4
Pasta, rice
Vegetables
Pulses
Meat
20
Cooking table
Food
categories
Fish
Dishes or type
of cooking
Power level and cooking stage
First stage
Power
Second stage
Power
Grilled
Preheating the grill
7-8
Grilling on both sides
7-8
Stewed
Browning with oil (if
with butter: power
level 6)
7-8
Cooking and
maintaining the
temperature
3-4
Fried
Heating the oil or fat
8-9
Frying, browning
7-8
Frittata
Heating the pan with
butter or fat
6
Grilling on both sides
6-7
Omelettes
Heating the pan with
butter or fat
6
Cooking
5-6
Soft/hard-boiled
Heating the water
Booster
–9
Cooking
5-6
Pancakes
Heating the pan with
butter
6
Grilling on both sides
5-6
Tomato
Browning with oil (if
with butter: power
level 6)
6-7
Cooking
3-4
Ragù
Browning with oil (if
with butter: power
level 6)
6-7
Cooking, maintaining a
light boil
3-4
Béchamel
Preparing the base
(melting butter and
adding flour)
5-6
Bringing to and
maintaining a light boil
3-4
Pastry cream
Bringing milk to the
boil
4-5
Bringing to the desired
consistency
4-5
Puddings
Bringing milk to the
boil
4-5
Bringing to the desired
consistency
2-3
Rice in milk
Heating the milk
5-6
Cooking
2-3
Eggs
Sauces
Desserts
Creams
21
22
23
WHIRLPOOL EUROPE s.r.l. Socio Unico
Printed in Italy
400010909878
GB
Download PDF

advertising