Whirlpool AKZ 286 IX Instruction for Use

Add to my manuals
12 Pages

advertisement

Whirlpool AKZ 286 IX Instruction for Use | Manualzz
CONTENTS
GB
INSTALLATION
PAGE
100
ELECTRICAL CONNECTION
PAGE
102
BEFORE USING THE APPLIANCES
PAGE
103
PROTECTING THE ENVIRONMENT
PAGE
103
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
PAGE
103
ENERGY SAVING TIPS
PAGE
104
OVEN ACCESSORIES
PAGE
105
COOKTOP ACCESSORIES
PAGE
105
OVEN FUNCTIONS
PAGE
106
COOKTOP FUNCTIONS
PAGE
107
CLEANING THE OVEN AND ITS ACCESSORIES
PAGE
107
CARE AND MAINTENANCE OF
CONVENTIONAL ELECTRIC COOKTOPS
PAGE
109
CARE AND MAINTENANCE OF THE
GLASS-CERAMIC COOKTOP
PAGE
109
TROUBLESHOOTING GUIDE
PAGE
109
AFTER-SALES SERVICE
PAGE
110
DECLARATION OF CONFORMITY CE
PAGE
110
99
INSTALLATION
Technical information for the installer
OVEN
• After removing the oven from its packaging, before
making the connections place it on the polystyrene
foam base to protect it from damage.
• Do not attempt to lift the oven by the handle.
Lift at the sides as shown in the figure (see arrow).
• Check that the appliance has not been damaged in
transit.
• Oven dimensions and kitchen unit dimensions are
shown in the figure opposite.
• Kitchen units in contact with the oven must be heat
resistant (80° C).
• If plastic laminates or cement are not sufficiently
heat-resistant, warping, bubbling or detachment of
the finish may result.
• Install the oven in the housing, lifting it at the sides,
taking care not to trap the wires of the electrical
supply cable.
•
•
•
•
For correct ventilation, follow the ventilation
opening directions shown in the figure
(500 x 80 mm min). An additional opening of 5 mm
is required between the oven top rim and the
cooktop lower rim: this opening must not be closed
by strips or housing crosspieces.
During oven installation, care must be taken to
ensure that the sides are not touching the front
edges of the housing or adjacent drawers and
doors (see picture).
Carry out the electrical connections between
cooktop and oven (see “Electrical Connection”).
Secure the oven to the kitchen unit with screws (A)
as shown.
100
No Contacts
INSTALLATION
Cooktop
•
•
•
•
The cooktop must be set into a worktop
between 20 mm and 50 mm thick.
There must be nothing between the cooktop
and the oven (cross rails, brackets, etc.).
If the cooktop is to be installed next to a
column unit, leave a distance of at least 100
mm from the edge of the cooktop to the side of
the column unit.
Cut an opening in the worktop of the dimensions
shown in the “Product Description Sheet” supplied
separately.
If not already present, fit the supplied seal to the
cooktop flange after cleaning the contact area as
shown in the top figure.
Cooktop with electric hotplates
•
If the worktop is made of wood, fit the supplied
clips.
1. Position the 4 spring clips (B) and fit them in their
locations on the underside of the cooktop.
2. Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc., the cooktop
must be secured with brackets (C) code
4819 310 18528 (to be requested from After Sales
Service).
1. Position the brackets over the holes and secure
them with the supplied screws.
2. Fit the cooktop into the worktop.
Glass-ceramic cooktop
N.B.: Remove the protective film before installing the
cooktop.
• If the worktop is made of wood, use the supplied
spring clips and screws.
1. Position the 4 clips (D) as shown and at the
specified dimensions.
2. Secure the clips using screws (E).
3. Fit the cooktop into the worktop.
• If the worktop is made of marble, plastic,
ceramics, natural stone, etc., the cooktop must
be secured with brackets (F) code 4819 404 78697
(to be requested from After-Sales Service).
1. Fit the cooktop into the worktop.
2. Position the 4 brackets (F) as shown in the figure,
in accordance with the thickness of the worktop.
3. Fix the 4 screws (G) in holes (H).
101
ELECTRICAL CONNECTION
•
•
Make sure the appliance is installed and
connected to the electricity supply by a
qualified technician in accordance with
the manufacturer’s instructions and in
compliance with local regulations.
The installer is responsible for the correct
electrical connection of the appliances
and the observance of the relative safety
recommendations.
•
•
•
•
Connecting the oven to the power supply
•
•
•
Make sure that the voltage shown on the rating
plate is the same as the power supply voltage in
your home. The service number is located on the
front edge of the oven cavity (visible when the
oven door is open).
Use a type H05RR-F power cord (minum length:
800 mm).
Warning: All the oven’s components operate at
230-240V. When using a 400 V connection,
make sure that the voltage reaching the oven is
230-240V, as illustrated in the side table.
Conductors X
number
1N+
~
2N+
~
3 +
~
3N+
~
Electrical
connection
H05 RR-F 3X4 mmq
H05 RR-F 4X2.5 mmq
H05 RR-F 4X2.5 mmq
H05 RR-F 5X1.5 mmq
Interconnecting cooktop and oven
•
•
•
•
Before connecting the oven to the power supply,
check that the cooktop is among the ones listed in
the cooktop/oven pairing product sheet.
Connect the 3 pole and 4 pole connectors to the
respective connectors on the oven.
The 3 pole connectors (H) is located at the rear
right hand side of the control panel, the 4 pole
connector (J) is located at the top of the oven in the
left hand corner (see figure).
Connect the yellow/green striped earth wire (
)
(K) from the cooktop to the screw located near the
3 pole connector.
WARNING: DO NOT CONNECT TO THE
POWER SUPPLY BEFORE YOU HAVE
FINISHED CONNECTING THE OVEN AND
THE COOKTOP.
Mount the oven in the kitchen unit.
Make sure the power cord is not entrapped.
102
The appliance must be connected to the
electricity supply by means of an all-pole
disconnect switch with minimum contact
gap of 3 mm.
The appliances must be earthed by law.
Do not use multiple plug adapters or
extension leads.
After the oven has been installed, the
electrical components must be
concealed.
BEFORE USING THE APPLIANCES
•
To make the most of your new appliances
read the users instructions carefully and keep
them on hand for consultation in the future.
•
Remove the cardboard protections and the
protective plastic film.
•
Remove the accessories from the oven and
heat it at 200° C for about an hour to
eliminate the smell of protective grease and
insulating materials. Keep the window open
during this procedure.
N.B.: The cooling fan runs continuously at
different speeds according to the
temperature value of the components when
the cooktop or the oven are in use.
Full speed: when the components are hot.
Reduced speed (on/off mode): when the
components are not hot.
The on/off mode must be considered the normal
mode when the fan is at reduced speed.
The fan may continue to run for the time
necessary to ensure sufficient cooling of the
components and adjacent kitchen units after
the appliances have been switched off.
PROTECTING THE ENVIRONMENT
1. Packing
• The packaging material is 100% recyclable
and it is marked with the recycle symbol
( ).
.
2. Appliances
• The appliances are built from recyclable
materials. If you decide to scrap the
appliances please observe local waste
disposal regulations. When you scrap them,
cut off the power cords so that the appliances
cannot be connected to the mains.
PRECAUTIONS AND GENERAL RECOMMENDATIONS
•
Before any maintenance on the appliances
disconnect them from the power supply.
•
Keep children away from the appliances
when they are in use.
•
The oven must be repaired or adjusted only
by a qualified technician.
•
Make sure that the electrical wires of other
electrical appliances near the oven do not
come into contact with hot parts and do not
become entrapped in the oven door.
•
During the cooking process, water
evaporates from food. All ovens require this
steam and other fumes to be vented from the
oven cavity. For reasons of safety and
aesthetics, we have determined that an
opening at the bottom of the door is the
optimum solution.
Consequently, vapour may be seen to be
coming from this area on occasions (see
picture). This is a normal occurrence and the
bottom trim can be cleaned after removal of
the door as described on page 107.
•
Heavy weights must not be placed on the
open door as this may result in damage to the
cavity and hinges. Max weight: 7 kg (15 lbs).
Fum
es
Ex h
aus
t
Oven
•
•
•
•
Never stand or sit on the oven open door.
Never hang any weight at the handle of the
oven door when open.
Use oven gloves to remove baking trays and
accessories when the oven is hot.
Do not cover the bottom of the oven with
aluminium foil.
Do not place inflammable material in the
oven - risk of fire if the oven is inadvertently
switched on.
103
PRECAUTIONS AND GENERAL RECOMMENDATIONS
Conventional electric / glass-ceramic
cooktop
Specific recommendations for glassceramic cooktops
•
•
•
•
•
•
Do not switch on the hotplates / cooking
areas when there is no pan in position.
The cooktop features hotplates/cooking
areas of different size. Use pans whose base
diameter is the same as or slightly larger than
the diameter of the hotplate/cooking zone.
Use flat-bottomed pans. The use of pans
with concave or convex bottoms is not
recommended.
Do not use the cooktop as a work or support
surface.
Do not leave the appliance unattended when
frying food -risk of fire.
•
•
•
•
•
When using the Fast Boiling function, use
stainless steel pans with double bottom only.
If the glass-ceramic surface should break or
crack due to violent impact (falling objects,
etc.) do not use it and call After-Sales Service
immediately.
Do not place food wrapped in aluminium foil,
plastic containers or cloths on the hot
cooking zones.
Do not drag pans across the glass-ceramic
surface - risk of scratches.
If the cooktop is fitted with halogen lamps, do
not stare at them when they are switched on.
Avoid spilling sugar and similar substances
on the cooktop. Should this happen, clean
the cooktop carefully following the care and
maintenance instructions in this handbook.
ENERGY SAVING TIPS
•
•
•
•
•
Use pots and pans whose bottom diameter is
equal to that of the cooking zone or slightly
larger.
Only use flat-bottomed pots and pans.
If possible, keep the pots covered when
cooking.
Cook vegetables, potatoes, etc. with little
water in order to cut down on cooking time.
A pressure cooker allows you to save even
more energy and time.
NO!
OK!
104
OVEN ACCESSORIES
•
Accessories supplied depend on the model
(refer to the “Product Description Sheet”
supplied separately).
1
Drip tray 1
The drip tray is designed to collect fat and food
particles when it is positioned under the grid; it can
also be used as a griddle to cook meat, chicken and
fish, with or without vegetables. To avoid spatters of
fat and smoke, pour a little water into the drip tray.
2
Baking tray 2
For cooking biscuits, meringues and pizzas.
Grid 3
The grid can be used to grill food or as a support for
baking trays, cake tins and other cooking receptacles.
It can be placed in two different ways (
or
) and
on any of the runners in the oven.
3
Catalytic panels 4
The catalytic panels have a microporous coating that
absorbs fat spatters. We recommend an automatic
cleaning cycle after cooking particularly fatty food.
4
5
1. To clean the oven heat it to 200° C when empty
and leave it switched on for about an hour.
2. At the end of the cycle, when the oven is cool, use
a moist sponge to remove food residues.
Do not use detergent or cleaners - risk of
damaging the catalytic enamel coating.
Spit 5
Use the spit as indicated in the relevant chapter in the
Product Description Sheet supplied separately.
6
Pan Set Kit 6
The set comprises a grid 6a , a drip tray 6b and one
or two tongs 6c .
This accessory must be set on the grid 3 and used
with the Grill function.
6a
6b
6c
.
COOKTOP ACCESSORIES
Child guard accessory AMH 122
This accessory can be obtained from the After-Sales
Service under Part N° 4819 310 18436 or from your
dealer under Ref. 017124.
105
OVEN FUNCTIONS
The functions actually available depend on the
model (see the Product Description Sheet
supplied separately).
STATIC FUNCTION
This function is used to cook food on the same
runner level.
The function allows temperature control; the
temperature can be set in the range of 50° C to
250° C. The default setting is 200° C.
• Preheat the oven until the required temperature
is reached and place the food into the oven
when all the indicators on the scale °C__ are on.
• When using this function, it is advisable to put
the food in the middle of the oven.
GRILL FUNCTION
This function is ideal to grill small pieces of meat
(steaks, sausages) and for making toast.
The function allows five settings, 1, 2, 3, 4, 5, each
corresponding to an increased heating level of the
heating element at the top.
The default setting is 3.
• During cooking, the oven door must be kept
closed.
• Preheat the oven for 3/5 minutes.
• When cooking meat, to avoid spatters of fat and
smoke, pour a little water into the drip tray.
• Turn the food half-way through grilling time.
When this function is selected the spit (if supplied)
is also activated.
“MLTF” FUNCTION (Heat maintenance)
This function keeps one of two temperature levels of
temperature (either 35° C or 60° C) inside the oven.
• Setting the temperature at 35° C is particularly
useful to raise dough for bread and pizza.
• The default setting is 35° C. For this function it
is advisable to use the first shelf level.
• Use the 60° C temperature setting to keep the
food warm once it is cooked.
FAN FUNCTION
This function is especially useful for
simultaneously cooking different foods at more
than one shelf level (for example: fish,
vegetables, pasta).
This function allows temperature control; the
temperature can be set in the range 50° C to 250° C.
The default setting is 160° C.
• If possible choose dishes that require the
same cooking temperature.
• It is not necessary to preheat the oven.
• If the dishes in the oven have different
cooking times, remove completed dishes and
leave remaining foods until cooked.
PASTRY FUNCTION (Static + Fan)
This function is useful when cooking at two levels
and when baking cakes. The function allows
temperature control; the temperature can be set in
the range of 50° C to 250° C.
The default setting is 175° C.
• It is not necessary to preheat the oven.
106
Switch the position of the dishes inside the oven
during cooking time.
• If the dishes in the oven have different cooking
times, remove completed dishes and leave
remaining foods until cooked.
TURBOGRILL FUNCTION (Grill + Fan)
This function is ideal to cook large chunks of meat
(i.e. roast beef, roasts).
The function allows five settings, 1, 2, 3, 4, 5, each
corresponding to an increasing heating level of the
heating element at the top. The default setting is 3.
• Keep the oven door closed while cooking.
• Lay the meat onto the grid and position the drip
tray on the first shelf level. To avoid spatters of fat
and smoke, pour a little water into the drip tray.
• Turn over the meat half-way through cooking time.
•
TURBOFAN FUNCTION
This function is useful when cooking at two runner
levels; the temperature can be set in the range of
50° C to 250° C.
The default setting is 160° C.
This function is ideal for:
• Large fruitcakes
• Timbales
• Stuffed vegetables
• Poultry (weighing more than 3 kg)
It is not necessary to preheat the oven.
PROGRAM FUNCTION
This function is useful to bake pizzas, bread and
focaccia. The function provides 3 cooking programs
(P1, P2, P3) with preset initial temperatures that
can be adjusted by the user.
The maximum temperature values that can be
adjusted by the user are: 240° C for P1, 200° C for
P2 and 190° C for P3 in order to obtain uniform
cooking results.
Each program corresponds to a recipe for the
preparation of the dish you want.
Programme P1 allows rapid preheating with an
initial temperature of 300° C and a cooking
temperature of 240° C.
To improve energy saving and avoid wasting
electricity, there is no preheating if the oven is
already warm, and the cooking temperature is set
automatically (240° C).
For programmes P2 and P3 the initial temperature
is always 220° C.
BOOSTER FUNCTION
This function allows fast preheating of the oven.
The function allows temperature control; the
temperature can be set in the range of 50° C to
250° C.
The default setting is 200° C.
As the temperature in the oven increases, the
indicators -----° C light up in sequence. When the
selected temperature is reached, an acoustic signal
is emitted and the oven switches automatically to
Static Function.
This function is ideal when cooking meat, fish and
poultry.
COOKTOP FUNCTIONS
The cooktop control knobs are marked with a
numerical scale corresponding to different power
settings, and a series of function symbols.
KEEP WARM FUNCTION
This function uses a low power setting so that food
can be kept warm when cooking is finished.
How to operate:
.
1. Turn the knob to
2. To deactivate the Keep Warm function, change
the knob position.
DUAL ZONE FUNCTION
(dependent on model)
This function is available on the front left and rear
left cooking zones. The dual-zone function extends
the heated area of the cooktop so that you can use
large, oval or rectangular pans.
How to operate:
and wait for the residual
1. Turn the knob to
heat indicator for the chosen hotplate to start
flashing.
2. Select the required power by turning the knob
anti-clockwise. The residual heat indicator
remains lit to show that the cooktop is switched
on.
3. To deactivate the function return the knob to “0”.
>>
ICP FUNCTION
(INITIAL COOKING PHASE)
This function accelerates the heating of the
selected cooking zone for a specified amount of
time during the first part of the cooking cycle.
How to operate:
.
1. Turn the knob to
2. Wait until the residual heat indicator starts
flashing, then turn the knob anti-clockwise to the
desired power level. For example: if the power
level is “1”, the cooking zone will operate at full
power for 1 minute, then it will switch to power
level “1” for the remainder of the cooking cycle,
>>
unless the position of the knob is changed. If the
power level is “6”, the cooking zone will operate
at full power for 6 minutes, then will switch to level
“6” for the rest of the cooking cycle, unless the
position of the knob is changed. This applies to all
power levels with the exception of level “10”.
FAST BOILING FUNCTION
This function makes it possible to bring water to the
boil fast; the Fast Boiling function remains active for
a preset time. Once the preset time has elapsed, the
cooktop returns automatically to maximum power
level. The Fast Boiling function can be activated
also once you have already started cooking.
Warning: Make sure you have placed the pan on
the cooking zone before activating the fast boiling
function or the glass-ceramic surface may be
damaged.
Specified performance values for the Fast Boiling
function are guaranteed for all types of glassceramic cooktops.
How to operate:
1. Place the pan on the chosen cooking zone.
.
2. Set the knob to
GENTLE HEAT FUNCTION
Can be used to raise dough, soften hard butter from
the fridge, keep a baby’s bottle or a baby food
warm, for yoghurt making, melting chocolate, etc...
This function is available only when the residual
heat indicator light is on.
How to operate:
1. Make sure that the relative cooking zone
residual heat indicator light is on.
.
2. Turn the knob to
3. To deactivate the function change the knob
position.
This symbol does not correspond to any
cooktop mode; the heating element is not
powered
CLEANING THE OVEN AND ITS ACCESSORIES
•
•
•
•
•
•
•
When you finish cooking wait for the oven to
cool and then clean it to prevent the build-up of
baked-on residues.
If the food residues are baked on, use a specific
oven cleaner and follow the manufacturer’s
instructions.
Clean the exterior of the oven with a sponge
and warm water.
Do not use abrasive cleaners or pan
scourers.
Use a liquid detergent to clean the oven door
window.
Wash the accessories in a dishwasher or in the
sink, using an oven cleaner.
After the oven has been in prolonged use and
when cooking on different levels (especially
food with high water contents such as pizzas,
stuffed vegetables, etc.) condensation may
form on the inside of the door and of the door
seal. When the oven is cool, dry any
condensation with a cloth or a sponge.
107
CLEANING THE OVEN AND ITS ACCESSORIES
Removing the oven door (for cleaning)
1. Open the oven door.
2. Press hinge catches (A) forwards.
3. Lift the catches until they engage and then remove
the door.
4. While you are cleaning the oven, ensure you do
not disengage the hinge retainer catches.
5. Refit the oven door by following the above steps in
reverse order.
How to clean the oven roof, pulling out the grill
element (if fitted) and lowering it as far as it will go
• Do not attempt to clean the oven until it is cool.
1. To clean the oven roof, pull out the grill element
and lower it as far as it will go.
2. Clean the oven roof and then return the grill
element to its original position.
Changing the oven lamp
1.
2.
3.
4.
5.
Disconnect the oven from electrical supply.
Unscrew the lamp cover.
Change the lamp (see N.B.).
Refit the lamp cover.
Reconnect the electrical supply.
Changing the lateral lamp (depending on model)
Disconnect the oven from the electrical supply.
Remove the left hand side grid.
Using a screwdriver, prize off the lamp cover.
Change the lamp (see N.B.).
Reposition the lamp cover and press it against the
oven wall until it clicks into place.
6. Refit the side grid.
7. Reconnect the electrical supply.
1.
2.
3.
4.
5.
N.B.: Use exclusively 25 W 230 V lamps, type E-14,
T300° C, available from After-Sales Service.
.
108
CARE AND MAINTENANCE OF
CONVENTIONAL ELECTRIC COOKTOPS
Before cleaning the cooktop, disconnect it from
the electrical supply and wait until it has cooled.
Care and Maintenance of conventional
electric cooktop
• Use a cloth and warm soapy water.
• Do not use abrasives, corrosive cleaners,
cleaners containing chlorine or pan scourers.
• Do not leave acidic substances on the
cooktop (vinegar, salt, lemon juice, etc.).
Stainless steel cooktop
• Use a proprietary cleaner for stainless steel.
N.B.: prolonged use of the cooktop may result in
slight discoloration of the stainless steel surfaces
around the hotplates. This is caused by the high
temperature of the hotplates.
Cleaning the hotplates
Clean the hotplates when they are warm (not
hot!). Use a cloth moistened with water and salt.
Dry and clean with a cloth moistened with
cooking oil.
CARE AND MAINTENANCE OF THE
GLASS-CERAMIC COOKTOP
Clean the cooktop, when it is cool, after each
use. This will prevent the build-up of dirt and
make cleaning easier.
• Use a clean cloth, absorbent kitchen wipes
and washing up liquid or a specific
glass-ceramic hob cleaner.
• Remove baked-on dirt with the supplied
scraper tool and specific cleaning products.
• Food spills should be cleaned off before they
bake onto the glass-ceramic surface.
• Do not use abrasive products, bleach,
oven-cleaner sprays or pan scourers.
• The cooktop should be treated periodically
with a proprietary brand of protective wax for
glass-ceramic hobs.
TROUBLESHOOTING GUIDE
Oven not working
• Switch the oven off and then on again to see
if the problem persists.
• Check for the presence of mains electrical
power.
• Check that the oven selector is not on
position “0”.
• If the electronic display presents the
message “STOP”, press the button 2 to
reset the oven and then set the clock (see the
Programmer Description Sheet supplied
separately).
• If the electronic display shows the message
“Fxx”, contact the After-Sales Service,
quoting the error code displayed.
Cooktop not working
• Check for the presence of mains electrical
power.
• Check that the control know is not set to “0”.
• Set to “OFF” the all-pole disconnect switch
for a few minutes, then set it back to “ON”.
109
AFTER-SALES SERVICE
•
Before contacting After-Sales Service:
1. Try to solve the problem
(see “Troubleshooting Guide”).
2. Turn off the appliance and restart it to see if the
fault is repeated.
If after the above checks the fault still occurs,
get in touch with the nearest After-Sales Service.
Please give:
• the nature of the problem,
• the exact type and model,
• the service number (number after the word Service
on the rating plate), located under the cooktop or
on the “Product Description” Sheet or, finally, on
the right hand edge of the oven cavity (visible
when the oven door is open). The service number
is also indicated on the guarantee booklet,
• Your complete address (including postal code)
and phone number.
DECLARATION OF CONFORMITY CE
•
•
•
•
These appliances are designed to come into
contact with foodstuffs and they are constructed in
compliance with Directive 89/109/EEC.
They are designed solely for use as domestic
cooking appliances. Any other use of the
appliances (e.g. for room heating) is considered as
improper use and potentially dangerous.
These appliances are designed, built and sold in
compliance with:
- the safety requirements of “Low Voltage”
Directive 73/23/EEC;
- the protection requirements of EMC Directive
89/336/EEC;
- the requirements of Directive 93/68/EEC.
This appliance complies with Class “Y” fire
protection category.
110

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement