Whirlpool ADG 689 IX Instruction for Use


Add to my manuals
10 Pages

advertisement

Whirlpool ADG 689 IX Instruction for Use | Manualzz
3GB94607.fm Page 13 Thursday, June 5, 2003 9:52 AM
INSTRUCTIONS FOR USE
BEFORE USING THE DISHWASHER/
CONNECTIONS
ELECTRICAL CONNECTION
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
HOW TO FILL THE SALT CONTAINER
HOW TO FILL THE RINSE AID DISPENSER
HOW TO FILL THE DETERGENT DISPENSER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
13
Black process 45.0° 100.0 LPI
3GB94607.fm Page 14 Thursday, June 5, 2003 9:52 AM
BEFORE USING THE DISHWASHER/
CONNECTIONS
1. Removing the packaging and controls:
After unpacking, make sure that the dishwasher is
undamaged and that the door closes correctly.
If in doubt, contact a qualified technician or your
local retailer.
• Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
• This dishwasher has been factory tested to ensure
it functions correctly.
Such testing may leave slight water marks that will
disappear with the first wash.
2. Water and electrical connections:
All water and electrical connections must be
carried out by a qualified technician in compliance
with the manufacturer's instructions (refer to the
enclosed installation booklet) and current local
safety regulations.
The appliance must only be used in the household
for the prescribed uses.
Do not use the dishwasher if it has been damaged in
transit. Consult your local retailer or our After-Sales
Service.
(Refer to the separate installation
instructions booklet)
3. Water inlet and drain:
• Observe any special regulations issued by your local
Water Board.
Water supply pressure: 0.3 - 10 bar.
• Make sure the inlet and drain hoses are kink-free
and are not crushed.
• If the hose length is not sufficient, please contact
your local dealer or our After-Sales Service.
• The inlet hose must be securely clamped to the
water tap to prevent leaks.
• The inlet water temperature varies according to
the model installed. Inlet hose marked “25°C Max”:
maximum temperature 25°C.
All other models: maximum temperature 60°C.
• When installing the appliance, make sure the drain
water discharges correctly (if necessary, remove
the wire gauze from the sink siphon).
• Fix the drain hose to the spigot with a clamp to
prevent it from coming off during operation.
14
Black process 45.0° 100.0 LPI
For appliances with water-stop system only: if the
water connections are made correctly, the waterstop system safeguards your home against damage
caused by flooding.
4. Electrical connection:
• Closely adhere to local Electricity Board
regulations.
• Voltage information is shown on the rating plate
mounted inside the door on the right hand side.
• The appliance must be earthed as prescribed by law.
• Do not use extension leads or multiple adapters.
• Before carrying out maintenance, disconnect the
mains plug.
• If necessary, the power cable may be replaced with
one the same obtained from our After-Sales
Service. The power cable must only be replaced by
a qualified technician.
• For Austria: if the apparatus is series connected to
a fault current switch, this must be sensitive to the
pulsating current.
3GB94607.fm Page 15 Thursday, June 5, 2003 9:52 AM
ELECTRICAL CONNECTION
1) For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A 13amp
fused plug, to change a fuse in this type of plug use an A.S.T.A.
approved fuse to BS 1362 type and proceed as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the fuse
cover is lost the plug must not be used until a correct replacement is
fitted.
Correct replacement are identified by the colour insert or the colour
embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical
store.
2) For the Republic of Ireland only
The information given in respect of Great Britain will frequently
apply, but a third type of plug and socket is also used, the
2-pin, side earth type.
3) Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please contact
Whirlpool Service for further instruction. Please do not attempt to
change plug yourself. This procedure needs to be carried out by a
qualified Whirlpool technician in compliance with the manufactures
instructions and current standard safety regulations.
15
Black process 45.0° 100.0 LPI
3GB94607.fm Page 16 Thursday, June 5, 2003 9:52 AM
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
1. Packing
The packing box may be fully recycled as
confirmed by the recycling symbol
.
2. Energy and water saving tips:
• Do not rinse crockery under running water.
• Always fully load the dishwasher before switching
on.
• If ecological energy sources are available,
such as solar panel heating, heat pumps or
centralised heating systems, the appliance may be
connected to the hot water mains up to a maximum
temperature of 60°C. Make sure the water inlet
hose is of the correct type. Refer to the
“Connections” chapter in these user instructions.
3. Disposal:
The appliance is built from reusable materials. If you
decide to scrap the dishwasher, it must be disposed
of in compliance with local waste disposal laws.
Before scrapping, cut off the power cable so that
the appliance cannot be connected to the mains.
• To prevent situations of potential danger to
children (e.g. danger of suffocation), break the lock
of the door so that it can no longer be closed.
4. Child safety:
• Children must not be allowed to play with the
dishwasher.
• Store the detergent, rinse aid and salt in a dry place
out of the reach of children.
5. Safety warnings:
• The open dishwasher door can only support the
weight of the loaded rack when pulled out.
Do not rest objects on the open door or sit or stand
on it: the appliance may topple over!
• Do not use solvents inside the dishwasher: risk of
explosion!
• Before cleaning or carrying out maintenance,
switch off the appliance, disconnect the mains plug
and turn off the water tap.
• If a fault occurs, switch off the appliance and turn off
the water tap.
• On completion of the programme switch off the
dishwasher and turn off the water tap.
• Repairs and technical modifications must be carried
out exclusively by a qualified technician.
• The water in the dishwasher is not potable.
16
Black process 45.0° 100.0 LPI
• Do not store inflammable liquids near the
dishwasher.
• Do not operate the appliance in the open air.
6. Resistance to frost:
If the appliance is placed in surroundings exposed
to the risk of frost, it must be drained completely.
Turn off the water tap, remove the flexible inlet
and outlet hoses, and let all the water run out.
7. For appliances with water stop system:
The water inlet hose and plastic casing contain
electrical components. Do not therefore cut the
hose or immerse the plastic casing in water.
If the hose is damaged switch off the appliance
immediately.
8. The appliance must be used at temperatures
between 5°C and 45°C.
EC Declaration of conformity:
This appliance has been designed, constructed and
distributed in compliance with the safety
requirements of EC Directives:
• 73/23/EC
• 89/336/EC
• 93/68/EC
Load capacity:
10 place settings.
3GB94607.fm Page 17 Thursday, June 5, 2003 9:52 AM
HOW TO FILL THE SALT CONTAINER
From a water hardness category of 1–2 (medium), before using the dishwasher for the first time, fill the salt
container with regeneration salt (to find out the hardness level of water in your area, contact your local Water
Board or check the last bill you received).
The dishwasher is equipped with an electronic control system that allows you to adjust the water softening system
to suit the local water hardness level.
Adjust the water softening system as follows:
If the water hardness level does not correspond to position h3 on the selector (setting on delivery) or if the water
hardness level changes:
Keep the “Delayed Start” button pressed until the DISPLAY shows the symbol “bS”.
• Press the Start button to access the water hardness level setting (the current value is shown on the display).
• Press the “Delayed Start” button again to select the most appropriate hardness level (h1, h2…h5). Use the
table below to select the correct setting.
• Press the Start button to quit programming mode.
If the water hardness level falls within category 1 (soft), no salt is required.
Hardness
level
German
degrees
French
degrees
1 soft
1 - 2 medium
2 average
3 medium-hard
4 hard
5 extremely hard
°dH
0-4
5-9
10 - 22
23 - 29
30 - 35
36 - 41
°fH
0-7
8 - 15
16 - 30
31 - 45
46 - 60
61 - 80
mmol/l
Clarke scale or
English degrees
°eH
Setting
0 - 0,7
0,9 - 1,6
1,8 - 4,0
4,1 - 5,2
5,4 - 6,3
6,5 - 7,4
0 - 5,0
6,3 - 11,3
12,5 - 27,5
28,8 - 36,3
37,5 - 43,8
45,0 - 51,3
.h0
.h1
.h2
.h3
.h4
.h5
How to fill the salt container
Warning: only use regeneration salts for use domestic dishwashers!
Do not fill the salt container with unsuitable substances, such as detergent,
as this will cause irreparable damage to the water softener system.
1. Remove the lower rack.
2. Unscrew the cap by turning it counter-clockwise.
3. When first using the dishwasher: fill the salt container to the rim
with water.
4. Fill the salt container with regeneration salt to the rim (using the
funnel provided) (when filling for the first time min. 1.5 kg and
max. 2 kg) and stir with a spoon handle.
5. Screw the cap back on by turning it clockwise.
6. Fit the lower rack.
7. If regeneration salt is to be added, immediately start a wash
programme (rinsing alone is not sufficient) in order to eliminate
any residual saline solution straight away and avoid corrosion.
Salt level indicator
The dishwasher is equipped with an electric or visual salt level
indicator (depending on the model installed).
Electric indicator
The salt level indicator lamp on the control panel lights up when the
salt container is empty.
Visual indicator
The float is clearly visible in the cap window when the salt container is
full (see photo).
The float lowers and is no longer visible when the salt container is empty.
17
Black process 45.0° 100.0 LPI
3GB94607.fm Page 18 Thursday, June 5, 2003 9:52 AM
HOW TO FILL THE RINSE AID DISPENSER
The rinse aid facilitates drying and prevents the formation of unsightly
spots and streaks on crockery. Before using the dishwasher for the
first time, fill the rinse aid dispenser. Only use rinse aids recommended
for use in domestic dishwashers.
1. Unscrew the cap A by turning it counter-clockwise (see drawing).
2. Fill the dispenser with rinse aid up to the dotted line “max”
(approx. 140 cc).
Immediately wipe away any rinse aid spilt accidentally! This prevents
the formation of excess suds which may spoil washing results.
3. Close the cover.
A
Thereafter, regularly check the rinse aid level.
How to adjust the rinse aid dosage regulator
Factory setting: medium position.
If you are not satisfied with washing or drying results, change the rinse
aid dosage setting.
1. Unscrew the cap (A) by turning it counter-clockwise (see drawing).
2. If crockery is prone to whitish streaks: reduce the dosage by
turning the dial (B) to a lower setting. If crockery is not perfectly
dry: increase the dosage by turning the dial to a higher setting.
3. Close the cover.
B
Rinse aid level indicator:
Visual indicator:
light
add rinse aid
dark
sufficient rinse aid.
Electric indicator (if provided):
The indicator lamp on the control panel lights up when more rinse aid
needs to be added.
18
Black process 45.0° 100.0 LPI
3GB94607.fm Page 19 Thursday, June 5, 2003 9:52 AM
HOW TO FILL THE DETERGENT DISPENSER
How to fill the detergent dispenser:
Only use detergents recommended for use in domestic dishwashers.
Only fill the detergent dispenser prior to starting a wash
programme.
C
1. Press button (C) to open the cover.
2. How to fill the detergent dispenser.
Programmes with pre-rinse:
- Pour two thirds of the recommended dosage into the large
compartment (B).
- Pour the remaining third into the small compartment (A).
A
B
Programmes without pre-rinse:
- Pour the entire recommended dosage into the large
compartment (B). If the recommended dosage on the
detergent pack is over 45 ml (maximum capacity of the large
compartment), pour the remaining detergent into the small
compartment (A).
3. Close the cover.
Detergent
Use good quality liquid or powder dishwasher detergents and/or
tablets (do not use hand dishwashing detergents).
In order to safeguard the environment, follow the manufacturer's
directions for use. Do not use more than the amount of detergent that
is recommended. Observe the manufacturer's safety warnings.
Keep these products out of reach of children.
If you use detergents in tablet form, follow the manufacturer's
directions for use.
If you use multi-action dishwasher detergents that incorporate rinse
aid and regeneration salt, follow the directions below:
• products that incorporate the rinse aid enhance the detergent
action only with some programs.
• products that do not require using regeneration salt may be
used only in areas with specific water hardness level.
Read the product user instructions carefully. If in doubt, contact the
detergent manufacturer.
The guarantee is not applicable if faults are caused by the use of these
products.
19
Black process 45.0° 100.0 LPI
3GB94607.fm Page 20 Thursday, June 5, 2003 9:52 AM
CARE AND MAINTENANCE
Before cleaning or carrying out maintenance, switch off the appliance,
disconnect the mains plug and turn off the water tap.
Cleaning the outside of the appliance:
To clean the outside of the appliance, use a neutral detergent and a
damp cloth.
Clean the control panel with a damp cloth only.
Do not use abrasive detergents.
Cleaning the inside of the dishwasher:
Regularly wipe the door seal and inside of the door with a damp cloth
to remove any food residue.
Upper spray arm:
1. Slacken the fixing nut (A) (by turning it counter-clockwise) and
detach the spray arm (B) by pulling it down.
2. Rinse the nozzles.
3. To remount the spray arm, align it and then tighten the fixing nut
(by turning it clockwise), paying attention not to bend it.
The fixing nut must be tightened until it clicks!
$
%
Make sure the spray arm rotates freely.
C
Lower spray arm:
1.
2.
3.
4.
Remove the spray arm by pulling it upwards (C).
Disconnect part (E) from (D) by pulling them apart.
Rinse the nozzles.
To remount the spray arm, align it with the mounting and insert it
by pushing it down.
Make sure the spray arm rotates freely.
20
Black process 45.0° 100.0 LPI
D
E
3GB94607.fm Page 21 Thursday, June 5, 2003 9:52 AM
CARE AND MAINTENANCE
Cleaning the filters:
F
1. Rotate the microfilter counter-clockwise (E) and extract it (F).
2. Place the microfilter central filter unit on a flat surface and push the
handle of the microfilter (I).
Extract the filter (I) by pulling it forwards and upwards.
Extract filter (I) from filter (H).
3. Extract the central steel filter (J).
4. Clean all the filters under running water.
Check that no impurities are left inside the dishwasher!
5. Reassemble the microfilter, replace the central steel filter (J) and
refit the microfilter.
E
The filter unit must be correctly assembled to ensure good
wash results!
G
I
H
J
G
21
Black process 45.0° 100.0 LPI
3GB94607.fm Page 22 Thursday, June 5, 2003 9:52 AM
TROUBLESHOOTING GUIDE
FAULT
E1
E2 - E9
DESCRIPTION
The anti-flood system has been tripped (where present).
The system that controls the water level in the dishwasher has been tripped.
E3
The dishwasher is unable to heat the water.
E4
Temperature probe disconnected.
E5
The dishwasher is unable to load water.
E6
The dishwasher is unable to drain water from the tank.
E7
The dishwasher is unable to measure the amount of water loaded precisely.
• Alarms E1, E2, E3, E4, E9 automatically “halt” the wash programme in progress, moving it to end of cycle.
• Alarms E5, E6 interrupt the wash programme in progress and, once the fault has been remedied, allow the
programme to continue.
• Alarm E7 is displayed at the end of the wash programme, which is nonetheless allowed to finish since the
appliance is not prevented from working properly.
To “reset” an alarm, you must:
• open or close the door or switch the dishwasher off and then back on again. After this course of action the
dishwasher may be programmed again.
Should the fault persist, contact an authorized Service Centre.
22
Black process 45.0° 100.0 LPI

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement