Whirlpool AKZM 748/IX Instruction for Use

Add to my manuals
23 Pages

advertisement

Whirlpool AKZM 748/IX Instruction for Use | Manualzz
EN
User and maintenance manual
Manual del Usuario y de Mantenimiento
Manual do utilizador e de manutenção
IMPORTANT SAFETY INSTRUCTIONS
These instructions shall also be available on website: www.whirlpool.eu
YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT
This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
All safety warnings are preceded by the danger symbol and the following terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
All safety warnings give specific details of the potential risk present
and indicate how to reduce risk of injury, damage and electric shock
resulting from improper use of the appliance. Carefully observe the
following instructions:
- Use protective gloves to perform all unpacking and installation
operations.
- The appliance must be disconnected from the power supply before
carrying out any installation work.
- Installation and maintenance must be carried out by a qualified
technician, in compliance with the manufacturer’s instructions and
local safety regulations. Do not repair or replace any part of the
appliance unless specifically stated in the user manual.
- Power cable replacement must be carried out by a qualified
electrician. Contact an authorized service centre.
- Regulations require that the appliance is earthed.
- The power cable must be long enough for connecting the
appliance, once fitted in its housing, to the main power supply.
- For installation to comply with current safety regulations, an allpole disconnect switch with minimum contact gap of 3 mm must
be utilized.
- Do not use multiple plug adaptors if the oven is fitted with a plug.
- Do not use extension leads.
- Do not pull the power supply cable.
- The electrical components must not be accessible to the user after
installation.
EN1
- If the surface of the induction plate is cracked, do not use it and
switch off the appliance to avoid the possibility of electric shock
(only for models with induction function).
- Do not touch the appliance with any wet part of the body and do
not operate it when barefoot.
- This appliance is designed solely for use as a domestic appliance
for cooking food. No other type of use is permitted (e.g.: heating
rooms). The Manufacturer declines all responsibility for
inappropriate use or incorrect setting of the controls.
- The appliance and its accessible parts become hot during use.
Care should be taken to avoid touching heating elements.
Very young (0-3 years) and young children (3-8 years) shall
be kept away unless continuously supervised.
- Children from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and
knowledge can use this appliance only if they are supervised or
have been given instructions on safe appliance use and if they
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children without supervision.
- During and after use, do not touch the heating elements or interior
surfaces of the appliance - risk of burns. Do not allow the appliance
to come into contact with cloths or other flammable materials until
all the components have cooled down completely.
- At the end of cooking, exercise caution when opening the
appliance door, letting the hot air or steam exit gradually before
accessing the oven. When the appliance door is shut, hot air is
vented from the aperture above the control panel. Do not obstruct
the vent apertures.
- Use oven gloves to remove pans and accessories, taking care not to
touch the heating elements.
- Do not place flammable materials in or near the appliance: a fire
may break out if the appliance is inadvertently switched on.
- Do not heat or cook sealed jars or containers in the appliance.
The pressure that builds up inside might cause the jar to explode,
damaging the appliance.
EN2
- Do not use containers made of synthetic materials.
- Overheated oils and fats catch fire easily. Always remain vigilant
when cooking foods rich in fat and oil.
- Never leave the appliance unattended during food drying.
- If alcoholic beverages are used when cooking foods (e.g. rum,
cognac, wine), remember that alcohol evaporates at high
temperatures. As a result, there is a risk that vapours released
by the alcohol may catch fire upon coming into contact with the
electrical heating element.
- Never use steam cleaning equipment.
- Do not touch the oven during the pyrolysis cycle. Keep children
away from the oven during the pyrolysis cycle. Excess spillage must
be removed from the oven cavity before cleaning cycle (only for
ovens with Pyrolysis function).
- Only use the temperature probe recommended for this oven.
- Do not use harsh abrasive cleaners or sharp metal scrapers to clean
the oven door glass since they can scratch the surface, which may
result in shattering of the glass.
- Ensure that the appliance is switched off before replacing the lamp
to avoid the possibility of electric shock.
- Do not use aluminium foil to cover food in the cooking vessel (only
for ovens with cooking vessel supplied).
Scrapping of household appliances
-
This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal
regulations. Before scrapping, cut off the power supply cable.
For further information on the treatment, recovery and recycling of household electrical appliances, contact your
competent local authority, the collection service for household waste or the store where you purchased the appliance.
INSTALLATION
After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly. In
the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the oven
from its polystyrene foam base at the time of installation.
PREPARING THE HOUSING UNIT
•
•
•
•
Kitchen units in contact with the oven must be heat resistant (min 90°C).
Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.
After installation, the bottom of the oven must no longer be accessible.
For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.
ELECTRICAL CONNECTION
Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front
edge of the oven (visible when the door is open).
•
Power cable replacement (type H05 RR-F 3 x 1.5 mm2) must be carried out by a qualified electrician. Contact an
authorized service centre.
EN3
GENERAL RECOMMENDATIONS
Before use:
-
Remove cardboard protection pieces, protective film and adhesive labels from accessories.
Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell and fumes from the
insulating materials and protective grease.
During use:
-
Do not place heavy objects on the door as they could damage it.
Do not cling to the door or hang anything from the handle.
Do not cover the inside of the oven with aluminium foil.
Never pour water into the inside of a hot oven; this could damage the enamel coating.
Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.
Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.
Do not expose the oven to atmospheric agents.
SAFEGUARDING THE ENVIRONMENT
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must
therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
-
This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment
(WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol
on the product or on the accompanying documentation indicates that it should not be treated as
domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic
equipment.
Energy saving tips
-
Only pre-heat the oven if specified in the cooking table or your recipe.
Use dark lacquered or enamelled baking moulds as they absorb heat far better.
Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will continue to cook even
once the oven is switched off.
DECLARATION OF CONFORMITY
-
-
This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.1935/2004
and has been designed, manufactured and sold in conformity with the safety requirements of the “Low Voltage” directive
2006/95/CE (which replaces 73/23/CEE and subsequent amendments), the protection requirements of “EMC” 2004/108/
CE.
This Appliance meets the eco design requirements of European regulations n. 65/2014, and n. 66/2014 in conformity to
the European standard EN 60350-1.
TROUBLESHOOTING GUIDE
The oven does not work:
•
•
Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
Turn off the oven and restart it to see if the fault persists.
The door will not open:
•
•
Turn off the oven and restart it to see if the fault persists.
Important: during self-cleaning, the oven door will not open. Wait until it unlocks automatically (see paragraph “Cleaning
cycle of ovens with pyrolysis function”).
The electronic programmer does not work:
•
If the display shows the letter “ ” followed by a number, contact your nearest After-sales Service. Specify in this case the
number that follows the letter “ ”.
EN4
AFTER-SALES SERVICE
Before calling the After-Sales Service:
1.
See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“.
2.
Switch the appliance off and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.
Always specify:
•
a brief description of the fault;
•
the type and exact model of the oven;
•
the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity
(visible when the oven door is open). The service number is also indicated on the guarantee booklet;
•
your full address;
•
your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used
and repairs carried out correctly).
CLEANING
WARNING
-
Never use steam cleaning equipment.
Only clean the oven when it is cool to the touch.
Disconnect the appliance from the power supply.
Oven exterior
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with
the appliance, clean immediately with a damp microfibre cloth.
•
Clean the surfaces with a damp microfibre cloth. If it is very dirty, add a few drops of washing up detergent to the water.
Finish off with a dry cloth.
Oven interior
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin enamelled surfaces
and the oven door glass.
•
After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove built-up dirt and
stains caused by food residues (e.g. food with a high sugar content).
•
Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.
•
Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate cleaning (see
MAINTENANCE).
•
The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean the roof of the oven.
N.B.: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.) condensation may form
on the inside of the door and around the seal. When the oven is cold, dry the inside of the door with a cloth or sponge.
Accessories:
•
•
Soak the accessories in water with washing up detergent immediately after use, handling them with oven gloves if still
hot.
Food residues can be easily removed using a brush or sponge.
Cleaning the rear wall and catalytic side panels of the oven (if present):
IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven sprays which could
damage the catalytic surface and ruin its self-cleaning properties.
•
Operate the oven empty with the fan-assisted function at 200°C for about one hour
•
Next, leave the appliance to cool down before removing any food residue with a sponge.
Cleaning cycle of ovens with pyrolysis function (if present):
WARNING
-
Do not touch the oven during the pyrolysis cycle.
Keep children away from the oven during the pyrolysis cycle.
This function burns off spatters produced inside the oven during cooking at a temperature of approx. 500°C. At this high
temperature, the deposits turn into a light ash which can be easily wiped away with a damp cloth, when the oven is cool. Do not
select the pyrolysis function after every use, only when the oven is very dirty or produces smoke or fumes while preheating or
cooking.
EN5
•
If the oven is installed below a hob, make sure that all burners or electric hotplates are switched off during the selfcleaning (pyrolysis) function.
•
Remove all accessories before running the pyrolysis function (also the lateral grids).
•
For optimum cleaning of the oven door, remove the worst soiling with a damp sponge before using the pyrolytic function.
•
The appliance is equipped with 2 pyrolysis functions:
1.
Energy-saving cycle (PYRO EXPRESS/ECO): which consumes approximately 25% less energy than the standard cycle.
Select it at regular intervals (after cooking meat on 2 or 3 consecutive occasions).
2.
Standard cycle (PYRO): which is suitable for cleaning a very dirty oven.
•
In any case, after a certain number of uses and depending on how dirty the oven is, a message on the oven display advises
you to run a self-cleaning cycle.
N.B.: during the pyrolysis function, the oven door will not open; it will remain locked until the temperature inside the
oven has returned to an acceptably safe level.
MAINTENANCE
-
WARNING
Use protective gloves.
Ensure the oven is cold before carrying out the following operations.
Disconnect the appliance from the power supply.
REMOVING THE DOOR
To remove the door:
1.
2.
3.
Open the door fully.
Lift the catches and push them forwards as far as they will go (fig. 1).
Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (fig. 2).
To refit the door:
1.
2.
3.
4.
Fig. 1
Insert the hinges in their seats.
Open the door fully.
Lower the two catches.
Close the door.
Fig. 2
MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)
1.
2.
3.
Fig. 3
Remove the side accessory holder grilles (Fig. 3).
Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).
To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to rest on the lateral
supports.
Fig. 4
Fig. 5
REPLACING THE OVEN LAMP
To replace the rear lamp (if present):
1.
Disconnect the oven from the power supply.
2.
Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on.
3.
Reconnect the oven to the power supply.
To replace the side lamp (if present):
1.
Disconnect the oven from the power supply.
2.
Remove the side accessory holder grilles, if present (Fig. 3).
3.
Use a screwdriver to prise off the lamp cover (Fig. 7).
EN6
4.
5.
6.
7.
Fig. 6
Replace the lamp (see note for lamp type) (Fig. 8).
Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).
Refit the side accessory holder grilles.
Reconnect the oven to the power supply.
Fig. 7
Fig. 8
Fig. 9
N.B.:
Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C halogen lamps.
The lamp used in the appliance is specifically designed for electrical appliances and is not suitable for household room
illumination (Commission Regulation (EC) No 244/2009).
Lamps are available from our After-sales Service.
IMPORTANT:
If using halogen lamps, do not handle with bare hands since fingerprints can damage them.
Do not use the oven until the lamp cover has been repositioned.
EN7
INSTRUCTIONS FOR OVEN USE
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
1. Control panel
2. Upper heating element/grill
3. Cooling fan (not visible)
4. Dataplate (not to be removed)
5. Light
6. Fan
7. Turnspit
8. Lower heating element (hidden)
9. Door
10. Position of shelves (the number of shelves is indicated on the front of the oven)
11. Rear wall
N.B.: During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
At the end of cooking, after the oven in switched off, the cooling fan may continue to run for a while.
When the oven door is opened during cooking, the heating elements switch off.
ACCESSORIES SUPPLIED
Fig. A
Fig. B
Fig. C
Fig. D
A. WIRE SHELF: the wire shelf can be used to grill food or as a support for pans, cake tins and other
ovenproof cooking receptacles.
B. DRIP TRAY: the drip tray is designed to be positioned under the wire shelf in order to collect fat or as
an oven tray for cooking meat, fish, vegetables, focaccia, etc.
C. TURNSPIT: for even roasting of large pieces of meat and poultry.
D. SLIDING RUNNERS: to facilitate insertion and removal of accessories.
The number of accessories may vary according to which model is purchased.
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-sales Service.
EN8
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
1.
2.
Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).
The other accessories, like the drip tray and baking tray, are inserted with the raised part on the flat
section “B” facing upwards (Fig. 2).
Fig. 1
Fig. 2
CONTROL PANEL DESCRIPTION
ELECTRONIC PROGRAMMER
1. FUNCTION SELECTOR KNOB: On/off and function selector knob
2. BROWSE KNOB: for browsing the menu and adjusting pre-set values
N.B.: the two knobs are retractable. Press the knobs in the middle and they pop up.
3. BUTTON : to return to the previous screen
4. BUTTON : to select and confirm settings
LIST OF FUNCTIONS
Turn the “Functions” knob to any position and the oven switches on: the display shows the functions or the
associated submenus.
The submenus are available and selectable by turning the knob to the functions GRILL, SPECIALS,
SETTINGS, BREAD/PIZZA, AUTOMATIC OVEN CLEANING.
N.B.: for the list and description of functions, see the specific table at page 14.
DESCRIPTION OF DISPLAY
I
H G
F
E
A
B
A.
B.
C.
D.
E.
F.
G.
H.
I.
C
D
Display of heating elements activated during the various cooking functions
Time management symbols: timer, cooking time, end of cooking time, time
Information regarding selected functions
Automatic BREAD/PIZZA function selected
Indication of door locked during automatic cleaning cycle (pyro-cleaning)
Internal oven temperature
Pyro-cleaning function
Browning
Special functions: Defrost, Keep Warm, Rising
STARTING THE OVEN - SETTING LANGUAGE
At the first switch on of the oven, the display shows: ENGLISH
Turn the “Browse” knob until the desired language is displayed, then press the button
EN9
to confirm.
SETTING TIME
After setting the language, the time must be set on the clock. The two hour digits flash on the display.
1. Turn the “Browse” knob to display the correct hour.
2. Press the button to confirm; the two minute digits flash on the display.
3. Turn the “Browse” knob to display the correct minutes.
4. Press button to confirm.
To change the time, for example following a power cut, see the next paragraph (SETTINGS).
SELECTING COOKING FUNCTIONS
1.
2.
Turn the “Functions” knob to the desired function: the cooking settings are shown on the display.
If the values shown are those desired, press . To change them, proceed as indicated below.
SETTING THE TEMPERATURE/OUTPUT OF THE GRILL
To change the temperature or output of the grill, proceed as follows:
1.
2.
Turn the “Browse” knob to display the desired value.
Press button to confirm.
FAST PREHEATING
1.
2.
3.
4.
Turn the “Functions” knob to the symbol to select the fast preheating function.
Confirm by pressing : the settings are shown on the display.
If the proposed temperature is that desired, press button . To change the temperature, proceed as
described in previous paragraphs. The message PRE appears on the display. When the set temperature
is reached, the corresponding value (e.g. 200°C) appears on the display and the acoustic signal
sounds. At the end of preheating, the oven automatically selects the conventional function .
At this point food can be placed in the oven for cooking.
If you wish to set a different cooking function, turn the “Functions” knob and select the desired
function.
SETTING COOKING TIME
This function can be used to cook food for a set length of time, from a minimum of 1 minute to the
maximum time allowed by the selected function, after which the oven switches off automatically.
1.
2.
3.
Once the temperature is confirmed, the symbol
flashes.
Turn the adjustment knob to display the desired cooking time.
To confirm the cooking time, press button .
EN10
SETTING END OF COOKING TIME / DELAYED START
IMPORTANT: the start delayed setting is not available for the following functions: FAST
PREHEATING, BREAD/PIZZA.
N.B.: with this setting, the selected temperature is reached in a more gradual way, so cooking times
will be slightly longer than stated in the cooking table.
The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and
59 minutes. This can only be done once cooking time has been set.
After setting cooking time, the display shows the end of cooking time (for example 15:45) and the
symbol
flashes.
To delay the end of cooking time, and thus also the cooking start time, proceed as follows:
1. Turn the “Browse” knob to display the time you wish cooking to end (for example 16:00).
2. Confirm the selected value by pressing button : the two dots of end of cooking time flash,
indicating that the setting has been made correctly.
3. The oven will automatically delay the start of cooking so as to finish cooking at the set time.
At any time, however, set values (temperature, grill setting, cooking time) can be changed using
button to go back, followed by the “Browse” knob to change values and button to confirm.
TIMER
This function can be used only with the oven switched off and is useful, for example, for monitoring the
cooking time of pasta. The maximum time which can be set is 23 hours and 59 minutes.
1. With the “Functions” knob at zero, turn the “Browse” knob to display the desired time.
2. Press button to start the countdown. When the set time has elapsed, the display will show “END”
and an acoustic signal will sound. To mute the acoustic signal, press button (the time of day
appears on the display).
SELECTING SPECIAL FUNCTIONS
Turn the “Functions” knob indicator to the symbol
to access a submenu containing three special
functions.
To browse, select and start one of these functions, proceed as follows:
1.
2.
3.
Turn the “Functions” knob to symbol
: the display shows ” DEFROST” along with this function’s
corresponding symbol.
Turn the “Browse” knob to scroll the list of functions: DEFROST, KEEP WARM, RISING.
Press button to confirm.
BROWNING
At the end of cooking, with certain functions, the display indicates the possibility of browning. This
function can only be used when cooking time has been set.
At the end of cooking time, the display shows: “PRESS TO BROWN”. Press button , and the oven starts
a 5-minute browning cycle. This function can be selected consecutively a maximum of twice.
EN11
BREAD/PIZZA FUNCTION SELECTION
Turn the “Function” knob pointer to the symbol
functions for “bread” and “pizza”.
to access a submenu containing the automatic baking
Bread
1.
2.
3.
4.
Turn the “Function” knob to the symbol
: the display shows “BREAD” and AUTO alongside.
Press to select the function.
Turn the “Browse” knob to set the required temperature (between 180°C and 220°C) and confirm with
button .
Turn the “Browse” knob to set the required cooking duration and press to start cooking.
Pizza
1.
2.
3.
4.
5.
Turn the Function knob to the symbol
: the display shows “BREAD”. To select the “PIZZA” function,
proceed as follows:
Turn the “Browse” knob: “PIZZA” appears on the display.
Press to select the function.
Turn the “Browse” knob to set the required temperature (between 220°C and 250°C) and confirm with
button .
Turn the “Browse” knob to set the required cooking duration and press to start cooking.
SETTING
Turn the “Functions” knob indicator to the symbol
settings which can be changed.
to access a submenu containing four display
Language
1.
2.
3.
Turn the “Browse” knob to display LANGUAGE.
Press to acces the setting
Turn the “Browse” knob until desired language is displayed then press the confirmation button
.
Clock
Turn the “Browse” knob to display CLOCK. To change the time of day, see the previous paragraph (SETTING
THE TIME).
Eco
With the ECO mode selected (ON), the display reduces the brightness, showing the clock when the oven is
in a stand-by position for 3 minutes. To view information on the display, simply press a button or turn a knob.
1. Turn the “Browse” knob to display “ECO”.
2. Press to access the setting (ON/OFF).
3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .
4. During a cooking function, if the Eco Mode is activated, the cavity lamp will be switched off after
1 minute of cooking and reactivated for each user interaction.
Acoustic signal
To activate or deactivate the acoustic signal, proceed as follows:
1. Turn the “Browse” knob to display “SOUND”.
2. Press to access the setting (ON/OFF).
3. Turn the “Browse” knob to select the desired setting and confirm by pressing button
.
Brightness
To change the display brightness, proceed as follows:
1. Turn the “Browse” knob to display “BRIGHTNESS”.
2. Press button : number 1 appears on the display.
3. Turn the “Browse” knob to increase or decrease brightness and confirm by pressing
EN12
.
AUTOMATIC OVEN CLEANING
For the description of this function, see the chapter CLEANING and the functions table at page 14.
To activate the oven’s automatic cleaning cycle (pyro-cleaning), proceed as follows:
1. Turn the “Functions” knob to symbol
: the word PYRO appears on the display.
2. Press button to confirm your choice and start the pyro-cleaning cycle.
To select ECO pyro-cleaning, turn the “Browse knob”: the word ECO appears bottom right on the display.
Press button to start the shorter programme.
During pyro-cleaning, the oven door is automatically locked and the symbol appears on the display. The
door remains locked at the end of the cleaning cycle: “COOL” appears on the display, indicating the oven
is still cooling down. When the oven cools to a safe temperature, the symbol switches off and the display
shows “END”.
KEY-LOCK
This function can be used to lock the buttons and knobs on the control panel.
To activate it, press and at the same time for at least 3 seconds. When activated, the functions
associated with the buttons are locked and the display shows a key symbol. This function can also be
activated during cooking. To deactivate it, repeat the above procedure. When the key-lock function is
activated, the oven can be switched off by turning the knob to 0 (zero). In this case, however, the previously
selected function will have to be set again.
EN13
FUNCTION DESCRIPTION TABLE
FUNCTION SELECTOR KNOB
OFF
LAMP
SPECIALS
DEFROST
KEEP WARM
RISING
CONVENTIONAL
CONVECTION
BAKE
GENTLE
CONVECTION
BAKE GENTLE FAN
GRILL
TURBO GRILL
MAXI COOKING
SETTINGS
To stop cooking and switch off the oven.
To switch the oven light on/off.
To speed up defrosting of food. Place food on the middle level. It is advisable to
leave food in its packaging to prevent it from drying on the outside.
For keeping just-cooked food (e.g. meat, fried food, flans) hot and crisp. It is
advisable to place food on the middle level. The function will not activate if the
compartment temperature is above 65°C.
For optimal proving of sweet or savoury dough. To preserve the quality of
proving, the function will not activate if the compartment temperature is
above 40°C. Place dough on the 2nd level. The oven does not have to be
preheated.
To cook any kind of dish on one shelf only. Use the 3rd level. To bake pizzas,
savoury pies and cakes with liquid fillings use the 1st or 2nd level. Preheat the
oven before placing food inside.
For baking cakes with liquid filling (sweet or savoury) on a single shelf. This
function can also be used for cooking on two shelves. Switch the position of
the dishes to cook food more evenly. Use the 3rd shelf to cook on one shelf
only, and the 1st and 4th to cook on two shelves. Preheat the oven before
cooking.
For cooking meat, filled pies (cheesecake, strudel, fruit pies) and stuffed
vegetables on one level only. This function uses discontinuous, delicate fan
assistance, which prevents excessive drying of foods. It is advisable to use 2nd
level. Preheat the oven before cooking.
To grill steak, kebabs and sausages; to gratinate vegetables and toast bread.
Place food on the 4th or 5th level. When grilling meat, it is advisable to use the
drip-tray to collect the cooking juices. Position it on the 3rd/4th level, adding
approx. half a litre of water. The oven does not have to be preheated. During
cooking the oven door must remain closed.
To roast large cuts of meat (legs, roast beef, chicken). Position food on the
middle levels. It is advisable to use the drip-tray to collect the cooking juices.
Position it on the 1st/2nd level, adding approx. half a litre of water. The oven
does not have to be preheated. During cooking, the oven door must remain
closed. With this function the spit can be used, if the relevant accessory is
provided.
To cook large joints of meat (above 2.5 kg). Use the 1st or 3rd shelves,
depending on the size of the joint. The oven does not have to be preheated. It
is advisable to turn the meat over during cooking for more even browning. It is
best to baste the meat every now and again to prevent it from drying out.
To set the display (language, time, brightness, buzzer volume, energy saving).
EN14
FUNCTION SELECTOR KNOB (Continued)
To bake different types and sizes of bread and pizza. This function has two
programmes with predefined settings. settings. Just indicate the required
BREAD/PIZZA values (temperature and time) and the oven will automatically manage the
optimum cooking cycle. Place the dough on the 2nd shelf after preheating the
oven.
To eliminate cooking spatters by means of a cycle at very high temperature
AUTOMATIC (approx. 500°). Two self-cleaning cycles are available: a complete cycle (PYRO)
OVEN
and a shorter cycle (ECO). It is advisable to use the complete cycle only in case
CLEANING
of a very dirty oven, and the shorter cycle if the function is used at regular
intervals.
FAST
PREHEATING
To preheat the oven rapidly.
EN15
COOKING TABLES
Recipe
Function
Pre- Shelf (from
heating bottom)
Yes
2/3
Temp.
(°C)
160-180
30-90 Cake tin on wire shelf
Yes
1-4
160-180
Shelf 4: cake tin on wire
shelf
30-90
Shelf 1: cake tin on wire
shelf
Yes
2
160-200
35-90
Leavened cakes
Filled pies (cheesecake, strudel, apple
pie)
GENTLE
Yes
1-4
160-200
Yes
3
170-180
15-45 Drip-tray / baking tray
Yes
1-4
160-170
Shelf 4: wire shelf
20-45 Shelf 1: drip-tray / baking
tray
Yes
3
180-200
30-40 Drip-tray / baking tray
Shelf 4: pan on wire shelf
35-45 Shelf 1: drip-tray / baking
tray
Choux pastry
Yes
1-4
180-190
Yes
3
90
110-150 Drip-tray / baking tray
Shelf 4: pan on wire shelf
130-150 Shelf 1: drip-tray / baking
tray
Meringues
Bread / Pizza /
Focaccia
Pizza
(Bread)
(Pizza)
Drip-tray / baking tray or
cake tin on wire shelf
Shelf 4: cake tin on wire
shelf (switch levels halfway
35-90 through cooking)
Shelf 1: cake tin on wire
shelf
Biscuits / Tartlets
Bread
Time Accessories and notes
(min)
Yes
1-4
90
Yes
1/2
190-250
15-50 Drip-tray / baking tray
Yes
1-4
190-250
Shelf 4: pan on wire shelf
(switch levels halfway
25-45 through cooking)
Shelf 1: drip-tray / baking
tray
Yes
2
180-220
30-50
Yes
2
220-250
15-30 Drip tray / baking tray
Yes
3
250
Yes
1-4
250
Frozen pizzas
EN16
Drip tray / baking tray or
wire shelf
Shelf 3: drip-tray / baking
tray or wire shelf
Shelf 4: pan on wire shelf
(switch levels halfway
10-20 through cooking)
Shelf 1: drip-tray / baking
tray
10-15
Recipe
Function
Pre- Shelf (from
heating bottom)
Yes
3
Temp.
(°C)
Time Accessories and notes
(min)
180-190
40-55 Cake tin on wire shelf
Yes
1-4
180-190
Shelf 4: cake tin on wire
shelf (switch levels halfway
40-55 through cooking)
Shelf 1: cake tin on wire
shelf
Yes
3
190-200
20-30 Drip-tray / baking tray
Yes
1-4
180-190
Shelf 4: pan on wire shelf
15-40 Shelf 1: drip-tray / baking
tray
Lasagne / Baked
pasta / Cannelloni /
Flans
Yes
3
190-200
45-65
Drip-tray or pan on wire
shelf
Lamb / Veal / Beef /
Pork 1 kg
Yes
2
180-190
80-120
Drip-tray or pan on wire
shelf
Yes
3
200-220
50-100
Drip-tray or pan on wire
shelf
Yes
2
190-200
80-130
Yes
3
180-200
Yes
2
170-190
-
5
3 (High)
Meat & potato pies
(vegetable pie,
quiche lorraine)
Vols-au-vent / Puff
pastry crackers
Chicken / Rabbit /
Duck 1 kg
GENTLE
GENTLE
Turkey / Goose 3 kg
Baked fish / en papillote (fillet, whole)
Stuffed vegetables
(tomatoes, courgettes, aubergines) GENTLE
Toast
Fish fillets / steaks
-
4
2 (Medium)
Drip-tray or pan on wire
shelf
Drip-tray or pan on wire
40-60
shelf
30-60 Pan on wire shelf
3-6
20-30
20-30
Sausages / Kebabs /
Spare ribs / Hamburgers
2-3
(MediumHigh)
-
5
-
2
-
2
Roast Beef rare 1 kg
-
3
2 (Medium) 35-50
Leg of lamb /
Knuckle
-
3
2 (Medium) 60-90
Roast potatoes
-
3
2 (Medium) 45-55
Roast chicken
1-1.3 kg
15-30
2 (Medium) 55-70
3 (High)
EN17
60-80
Wire shelf
Shelf 4: wire shelf (turn food
halfway through cooking)
Shelf 3: drip-tray with water
Shelf 5: wire shelf (turn food
halfway through cooking)
Shelf 4: drip-tray with water
Shelf 2: wire shelf (turn food
two thirds of the way
through cooking)
Shelf 2: turnspit (if present)
Pan on wire shelf (if
necessary, turn food two
thirds of the way through
cooking)
Drip-tray or pan on wire
shelf (if necessary, turn food
two thirds of the way
through cooking)
Drip-tray / baking tray (if
necessary, turn food two
thirds of the way through
cooking)
Recipe
Gratinated
vegetables
Function
Pre- Shelf (from
heating bottom)
Temp.
(°C)
-
3
3 (High)
Lasagna & Meat
Yes
1-4
200
Carne & Potatoes
Yes
1-4
200
Fish & Vegetables
Yes
1-4
180
Time Accessories and notes
(min)
Drip-tray or pan on wire
10-25
shelf
Shelf 4: pan on wire shelf (if
necessary, turn food two
thirds of the way through
50-100*
cooking)
Shelf 1: drip-tray or pan on
wire shelf
Shelf 4: pan on wire shelf (if
necessary, turn food two
thirds of the way through
45-100*
cooking)
Shelf 1: drip-tray or pan on
wire shelf
Shelf 4: pan on wire shelf
*
30-50*
Shelf 1: drip-tray or pan on
wire shelf
Cooking time is approximate. Food can be removed from the oven at different times depending on
personal preference.
EN18
Tested Recipes Table (in compliance with regulations IEC 60350-1:2011-12 and DIN 3360-12:07:07)
Recipe
Function
Pre- Shelf (from Temp.
heating bottom)
(°C)
Time Accessories and notes
(min)
IEC 60350-1:2011-12 § 7.5.2
Yes
3
170
15-25 Drip-tray / baking tray
Yes
1-4
160
Shelf 4: baking tray (switch levels
25-35 halfway through cooking)
Shelf 1: drip-tray/baking tray
Yes
3
170
20-30 Drip-tray / baking tray
Yes
1-4
160
Shelf 4: baking tray (switch levels
25-35 halfway through cooking)
Shelf 1: drip-tray/baking tray
Yes
2
170
30-40 Cake tin on wire shelf
Yes
2/3
185
55-75 Cake tin on wire shelf
Shelf 4: cake tin on wire shelf
(switch levels halfway through
75-95
cooking)
Shelf 1: cake tin on wire shelf
Shortbread
IEC 60350-1:2011-12 § 7.5.3
Small cakes
IEC 60350-1:2011-12 § 7.6.1
Fatless sponge
cake
IEC 60350-1:2011-12 § 7.6.2
Two apple pies
Yes
1-4
175
-
5
3 (High)
-
5
3 (High) 18-30
-
5
3 (High) 18-30 Shelf 4: drip-tray with water
Yes
3
180
30-40 Drip-tray / baking tray
Yes
1-4
160
Shelf 4: baking tray (switch levels
50-60 halfway through cooking)
Shelf 1: drip-tray/baking tray
-
2
170
Yes
3
170
35-45 Drip-tray / baking tray
160
Shelf 4: baking tray (switch levels
40-50 halfway through cooking)
Shelf 1: drip-tray/baking tray
IEC 60350-1:2011-12 § 9.2
Toast**
3-6
Wire shelf
IEC 60350-1:2011-12 § 9.3
Burgers**
Shelf 5: wire shelf (turn food
halfway through cooking)
DIN 3360-12:07 § 6.5.2.3
Apple cake, yeast
tray cake
DIN 3360-12:07 § 6.6
Roast pork
110-150 Shelf 2: drip-tray
DIN 3360-12:07 annex C
Flat cake
Yes
1-4
The cooking table advises the ideal function and temperature to ensure the best results with all recipes. If
you wish to cook on one shelf only using the fan-assisted function, place food on the third shelf and select
the temperature recommended for the “CONVECTION BAKE” function on more than one shelf.
The indications in the table are without use of the runners. Do the tests without the runners.
** When grilling food, it is advisable leave a space of 3-4 cm from the front edge of the grill to facilitate removal
Energy efficiency class (according to EN 60350-1:2013-07)
To do the test, use the dedicated table.
EN19
RECOMMENDED USE AND TIPS
How to read the cooking table
The table indicates the best function to use for any given food, to be cooked on one or more shelves at the
same time. Cooking times start from the moment food is placed in the oven, excluding pre-heating (where
required). Cooking temperatures and times are purely for guidance and will depend on the amount of food
and type of accessory used. Use the lowest recommended values to begin with and, if the food is not
cooked enough, then move on to higher values. Use the accessories supplied and preferably dark coloured
metal cake tins and oven trays. You can also use pans and accessories in pyrex or stoneware, but bear in
mind that cooking times will be slightly longer. obtain best results, carefully follow the advice given in the
cooking table for the choice of accessories (supplied) to be placed on the various shelves.
Cooking different foods at the same time
Using the “CONVECTION BAKE” function, you can cook different foods which require the same cooking
temperature at the same time (for example: fish and vegetables), using different shelves. Remove the food
which requires less cooking time and leave food which requires longer cooking time in the oven.
Desserts
-
-
Cook delicate desserts with the conventional function on one shelf only. Use dark coloured metal
cake tins and always position them on the wire shelf supplied. To cook on more than one shelf, select
the forced air function and stagger the position of the cake tins on the shelves, aiding optimum
circulation of the hot air.
To check whether a raising cake is cooked, insert a wooden toothpick into the centre of the cake. If
the toothpick comes out clean, the cake is ready.
If using non-stick cake tins, do not butter the edges as the cake may not rise evenly around the edges.
If the cake “sinks” during cooking, set a lower temperature the next time, perhaps reducing the
amount of liquid in the mixture and mixing more gently.
For sweets with moist fillings (cheesecake or fruit pies) use the “CONVECTION BAKE” function. If the
base of the cake is soggy, lower the shelf and sprinkle the bottom of the cake with breadcrumbs or
biscuit crumbs before adding the filling.
Meat
-
Use any kind of oven tray or pyrex dish suited to the size of the piece of meat being cooked. For roast
joints, it is best to add some stock to the bottom of the dish, basting the meat during cooking for
added flavour. When the roast is ready, let it rest in the oven for another 10-15 minutes, or wrap it in
aluminium foil.
When you want to grill meat, choose cuts with an even thickness all over in order to achieve uniform
cooking results. Very thick pieces of meat require longer cooking times. To prevent the meat from
burning on the outside, lower the position of the wire shelf, keeping the food farther away from the
grill. Turn the meat two thirds of the way through cooking.
To collect the cooking juices it is advisable to place a drip-tray with half a litre of water directly under the
grill on which the meat is placed. Top-up when necessary.
Turnspit
Use this accessory to evenly roast large pieces of meat and poultry. Place the meat on the spit rod, tying it
with string if chicken, and check that it is secure before inserting the rod in the seat located on the front
wall of the oven and resting it on the respective support. To prevent smoke and to collect cooking juices,
it is advisable to place a drip-tray with half a litre of water on the first level. The rod has a plastic handle
which must be removed before starting to cook, and used at the end of cooking to avoid burns when
taking the food out of the oven.
Pizza
Lightly grease the trays to ensure the pizza has a crispy base. Scatter the mozzarella over the pizza two
thirds of the way through cooking.
Dough proving function
It is always best to cover the dough with a damp cloth before placing it in the oven. Dough proving time
with this function is reduced by approximately one third compared to proving at room temperature
(20-25°C). Proving time for a 1 Kg batch of pizza dough is around one hour.
EN20
400010742585
GB
ES
PT
Whirlpool® Registered trademark/TM Trademark of Whirlpool, USA
Printed in Italy
02/2012

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions and Answers

Is it okay to cover the bottom of the oven with aluminum foil?
No, it is not recommended to cover the bottom of the oven with aluminum foil.
What should be done before using the oven for the first time?
Remove cardboard protection pieces, protective film, and adhesive labels from accessories. Heat the oven at 200°C for about an hour to eliminate the smell and fumes from insulating materials and protective grease.
How to clean the oven door glass?
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.
Is it okay to hang things from the oven door?
No, it is not recommended to hang anything from the oven door.
What is the recommended power cable type?
H05 RR-F 3 x 1.5 mm2

Related manuals

Download PDF

advertisement