LADEN HCH 990 IX Installation instructions

EXTRACTOR OR FILTERING HOOD INSTALLATION
The minimum distance between the support surface of the recipients on the cooking device and the lowest part of
the hood must not be less than 60 cm in case of electric cookers and 70 cm for gas or combination cookers. If the
installation instructions for the gas cooker specify a greater distance, this must be taken into account. Contact a
qualified technician for installation.
Do not connect the hood to the electrical power supply until installation is completed.
Warning! The exhaust pipe and clamps are not supplied and must be bought separately.
Very heavy product; hood handling and installation must be carried out by at least two persons.
Before beginning installation, decide which version of the hood you wish to use:
Extractor Version: fumes are extracted and expelled to the outside through an exhaust duct fixed to the collar (B) at the top
of the hood.
Warning! If the hood is has a carbon filter fitted, the filter must be removed.
Filter Version: air is filtered through two carbon filters and recycled into the surrounding environment.
Warning! If the hood is not equipped with carbon filters, they must be ordered and fitted before use.
1. Mark a centre-line on the wall from the cooktop to the ceiling.
2. Bearing in mind the minimum heights over the cooktop specified above, mark the height of the hood on the wall with a
pencil
and place the template against the wall on the mark.
3. Using the template supplied, mark the holes, drill them and insert the rawlplugs, partly tighten 1 screw in the top rawlplug.
4. Fix the flue support to the wall as close as possible to the ceiling.
5. Hook the hood.
6. Adjust the position.
7. Fully tighten the top fixing screw.
8. Remove the grease filters and fix the hood from inside using 2 screws and washers.
9. depending on hood version:
Extractor Version:
Fix an exhaust duct with the right diameter to the exhaust outlet of the hood and connect to an exhaust system ducted to the
outside (for fixture and connection of exhaust duct, utilize the most suitable system for the duct purchased).
Filter Version
Install the filter connection F on the collar B and secure with 1 screw.
• Connect the hood to the power supply!
Telescopic flue installation:
10. Fix the telescopic flue tot he support with two screws.
11. Slide the bottom section down into its seat on the top of the hood.
5019 618 33303
D
GB
F
NL
E
P
I
GR
* Only on some models
5019 618 33303
D
GB
F
NL
E
P
I
GR
Replacing bulbs
Disconnect the appliance from the power supply.
Warning! Make sure lamps are cold before touching them.
1. Remove the clip that secures the lamp cover, then prise off
using a small screwdriver or other suitable tool.
2. Replace the burnt-out bulb. Use a 40W max (E14) bulb
only.
3. Refit the lamp cover and secure in place with the clip.
Note: the lamp can also be accessed by removing the grease
filters, but removing the lamp in this way is more difficult.
DESCRIPTION OF HOOD
5
6
3 1
2
4
1. Control panel.
Light
:
move the switch to the right or press the button to switch
on.
Extraction speed
:
Move the switch to the right or press the next button to
increase extraction speed (or open the electric shutter ) .
2. Grease filter (the number of grease filters may vary,
depending on the model).
3. Grease filter handle.
4. Lamp covers (the number and position of lamps and/or
lamp covers may vary, depending on the model).
5. Telescopic flue.
6. Air vent (Filter version only)
Grease filters:
a
Metal grease filters have an unlimited life
and should be washed once a month
either by hand or in a dishwasher at a
low temperature and with a short cycle.
Washing in a dishwasher can cause
grease filters to turn white, but this in no
way affects efficiency.
Removing the filter: push the spring
release handle backwards (b) then
remove the filter downwards (a).
Wash the filter and leave it to dry, proceeding in reverse
order to refit it.
b
Carbon filters (filter hoods only):
Change the carbon filter every four months.
It cannot be washed or regenerated.
Fitting or replacing the carbon filter (filter hoods only).
1. Remove the grease filters.
2.Fit the filter/s over the motor: make sure the pins R on
the manifold match the slots S, then turn clockwise until
locked.
3. Refit the grease filters.
5019 618 33303
D
GB
F
NL
E
P
I
GR
SAFEGUARDING THE ENVIRONMENT
Electrical connections
1. Packing
The packing materials are 100% recyclable and are marked with
the recycling symbol
. Comply with local regulations for
disposal. Packaging materials (plastic bags, polystyrene, etc.) can
be dangerous for children and should be kept well out of their
reach.
2. Product
This appliance is marked in compliance with European Directive
2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE).
By ensuring that this appliance is scrapped suitably, you can help
prevent potentially damaging consequences for the environment
and health.
The mains power supply must correspond to the voltage
indicated on the appliance rating plate located inside the hood. If
provided with a plug, connect the hood to a power socket
complying with current regulations and located in an accessible
area. If it does not have a plug (direct connection to the power
supply) or if the socket is not in an accessible place, fit a suitable
double-pole switch that ensures complete disconnection from
the power supply in category III overvoltage conditions,
complying with the installation rules.
IMPORTANT: Before reconnecting the hood circuit to the
power supply and checking correct operation, always
make sure the power cable is correctly fitted and that it
was NOT crushed in its housing during installation.
The symbol
on the product or the accompanying
documentation indicates that this product should not be treated
as domestic waste but must be taken to a suitable collection
centre for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local
environmental regulations for waste disposal.
For further information on the treatment, recovery and recycling of
this appliance, contact your competent local authority, the collection
service for household waste or the shop where you purchased the
appliance.
Warning! Failure to remove oil/grease (at least once a month) could
result in fire.
Use a soft cloth with a neutral detergent. Never use abrasive
substances or alcohol.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
Declaration of conformity
IMPORTANT!
•
The appliance is not intended for use by young
children or persons with restricted physical, sensory or
mental abilities or without experience and knowledge
of the appliance, unless they are under the supervision
or instruction of a person responsible for their safety.
•
Young children should be supervised to ensure that they
do not play with the appliance.
1. Do not connect the appliance to the mains power supply until
installation has been fully completed. Always disconnect the
hood before cleaning or carrying out maintenance by
unplugging it or switching off the power supply.
2. Do not “flambé” food under the hood. Naked flames could
cause a fire.
3. Do not leave pans unattended when frying. Cooking oil can
catch fire.
4. Regular cleaning and maintenance is essential to correct
functioning and good performance. Regularly remove dirt
deposits. Regularly clean or replace filters. Never use flammable
materials as hoses for extracted air.
5. If the hood is used together with other appliances operating on
gas or other fuels, the negative pressure in the room must not
exceed 4Pa (4 x 10-5 bar). For this reason, make sure the room
is adequately ventilated.
6. Exhaust air must not be conveyed through the same flue used
by the heating system or other appliances powered by gas or
other fuels.
7. The room must be adequately ventilated when the hood is used
together with appliances powered by gas or other fuels.
8. Make sure lamps are cold before touching them.
9. The discharge air must not be ducted to a flue used for
removing fumes produced by appliances using gas or other
fuels, but must have a separate outlet. All national
regulations on air discharge must be observed.
10. The hood is not a shelf, therefore do not overload or place
objects on it
Note: Always wear work gloves for all installation and
maintenance operations.
5019 618 33303
D
GB
F
NL
Cleaning the hood
Before using the hood
To ensure best use of your hood, please read these instructions
carefully and keep them for future reference.
Packaging materials (plastic bags, polystyrene, etc.) can be
dangerous for children and should be kept well out of their
reach.
Make sure the hood has not been damaged during transport.
This product has been designed, manufactured and sold in
conformity to the following standards:
- safety objectives of the “Low Voltage” Directive 2006/95/CE
(which replaces 73/23/CEE and subsequent amendments)
- protection requirements of “EMC” Directive 89/336/EEC
amended by Directive 93/68/EEC.
Troubleshooting guide
The hood does not work:
• Is the plug properly inserted in the power socket?
• Is there a power failure?
The hood is not extracting sufficiently:
• Is the right speed selected?
• Do the filters need cleaning or changing?
• Are the air outlets blocked?
The light does not work:
• Does the lamp need replacing?
• Is the lamp correctly fitted?
AFTER-SALES SERVICE
Before calling the After-Sales Service
1. Check to see if you can fix the problem yourself (see
“Troubleshooting Guide”).
2. Switch the hood off and then on again to check if the
problem has gone.
3. If the problem persists, contact the After-Sales Service.
Specify:
• the nature of the problem,
• the product model given on the dataplate inside the hood,
visible on removing the grease filters.
• your full address,
• your telephone number and area code.
• the Service code (the number under the word SERVICE on
the dataplate inside the hood, behind the grease filter).
If any repairs are necessary, contact an authorised Service Centre (to
ensure the use of original spare parts and correct repair).
Failure to comply with these instructions can compromise the
safety and quality of the product.
E
P
I
GR