advertisement
▼
Scroll to page 2
of 8
31902047GB.fm Page 92 Wednesday, May 21, 2008 6:28 PM INSTRUCTION FOR USE BEFORE USING THE GLASS CERAMIC HOB INSTALLATION ELECTRICAL CONNECTIONS ENERGY SAVING TIPS SAFEGUARDING THE ENVIRONMENT PRECAUTIONS AND GENERAL ADVICE HOB ACCESSORIES CARE AND MAINTENANCE OF THE GLASS CERAMIC HOB TROUBLESHOOTING GUIDE AFTER-SALES SERVICE 92 31902047GB.fm Page 93 Wednesday, May 21, 2008 6:28 PM BEFORE USING THE GLASS CERAMIC HOB CAUTION: This cooktop complies with all applicable safety and electromagnetic compatibility legislation. However, persons with pacemaker should keep at a safe distance from the appliance. This is because it is not possible to guarantee that all pacemakers on the market comply with the standards in compliance with which this appliance was tested so it is not possible to provide an absolute guarantee of the absence of potentially harmful interference. • To make the most of your new appliance, please read the user instructions carefully and keep them handy for future consultation. INSTALLATION Hob • The hob must be set into a worktop between 20 mm and 50 mm deep • For the distance between the underside of the glass ceramic hob and the cupboard or separating panel, observe the dimensions given in figure “A”. • If the hob is to be installed next to a column unit, leave a distance of at least 100 mm from the edge of the hob. • Make an opening in the worktop of the dimensions shown in the Product Description Sheet supplied separately. • Apply the supplied gasket to the hob (unless it has already been fitted), after having cleaned its surface. Important In order to prevent the electronic circuits from overheating, and therefore from being damaged, we recommend the following: • Do not install the hob near a dishwasher or washing machine, so that the electronic circuits do not come into contact with steam or moisture, which could damage them. If an oven (which must be of our manufacture) is to be installed under the hob, ensure it is equipped with a cooling system and observe the distances given in figure “B”. There must be nothing between the hob and the oven (cross rails, panels, brackets, etc.). If the oven has a self-cleaning function (pyrolysis), do not use the hob whilst this function is selected. If the temperature of the electronic circuits exceeds the maximum permitted temperature, the hob will switch off automatically; in this case, wait for a few minutes until the internal temperature of the electronic circuits reaches a tolerable level, at which point it will be possible to switch the hob on again. • Switch the hob off after use. Rear wall Front A B 93 31902047GB.fm Page 94 Wednesday, May 21, 2008 6:28 PM INSTALLATION Assembly A) If the worktop is made of wood, use the appropriate brackets, spring clips and screws provided. • Position the 4 clips (A) around the hob frame, in the slots provided, see Fig. 1 • Measure the centre of the vertical sides of the cut out a shown in Fig. 2. • Position the centre of the brackets (C) on the centre of the side previously identified. • The upper edge of the brackets must be flush with the worktop surface. • Secure by means of the 4 screws (B) provided, using the pre-drilled holes. • Insert the hob into the pre-prepared hole ensuring that the clips (A) lodge into the bracket slots provided (C Fig. 4 e 5). • If the worktop is made of marble, ceramic, stone, plastic materials, etc., order the installation kit, code 4812 310 19277 from an authorized after-sales service. Fig. 1 A Fig. 2 C B Fig. 3 A Fig. 4 Fig. 5 94 31902047GB.fm Page 95 Wednesday, May 21, 2008 6:28 PM ELECTRICAL CONNECTIONS Electrical connection must be made before connecting the appliance to the electricity supply. The appliance must be installed by a qualified electrician who is fully aware of current safety and installation regulations. Specifically, installation must be carried out in compliance with the regulations of the local electricity supply company. Make sure that the voltage indicated on the rating plate corresponds to the voltage in your home. Regulations require that the appliance be earthed: use conductors (including the earth conductor) of the appropriate size only. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the above regulations. For the electrical connection use a H05 RR-F type cable as indicated in the table below: Power supply voltage. Conductors Amount x size 230V ~ + 3 X 2.5 mm2 230-240V ~ + 3 X 2.5 mm2 (Australia only) 230V 3~ + 4 X 1.5 mm2 400V 3N ~ + 5 X 1.5 mm2 400V 2N ~ + 4 X 1.5 mm2 If the hob comes already supplied with a power supply cable, see the diagram for connection to the mains electricity supply. The appliance must be connected to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm. Attention: the power supply cable must be long enough to allow the hob to be removed from the worktop and must be positioned so as to avoid damage or overheating caused by contact with the base. Connecting to the terminal board N.B.: the yellow/green earth wire must be connected to the terminal with the symbol and must be longer than the other wires. • Open the terminal board as shown on the cover “A” • Remove approx. 70 mm of the cable sheath from the power supply cable (B). • Strip approx. 10 mm of sheath from the wires. Then insert the power supply cable into the cable clamp and connect the wires to the terminal block as indicated in the connection diagram placed close to the terminal block itself. • Secure the power supply cable (B) by means of the cable clamp. • Close the terminal board with the cover (A) securing it with the screw provided. • After the electrical connection, fit the hob from the top and hook it to the support springs, following the diagram. Each time the hob is connected to the mains it carries out an automatic check which lasts several seconds. 95 31902047GB.fm Page 96 Wednesday, May 21, 2008 6:28 PM ENERGY SAVING TIPS • Use pots and pans whose bottom diameter is equal to that of the cooking zone or slightly larger. • Only use flat-bottomed pots and pans. • If possible, keep pot lids on when cooking. • Cook vegetables, potatoes, etc. with little water in order to cut down cooking time. • A pressure cooker allows you to save even more energy and time. NO! TO OBTAIN THE BEST RESULTS: • Make sure you place the pot or pan in the centre of the cooking zone outlined on the glass ceramic induction hob. SAFEGUARDING THE ENVIRONMENT 1. Packing • The packaging material is 100% recyclable and marked with the recycling symbol ( ). 2. Products This appliance is marked in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent potentially damaging consequences for the environment and health. The symbol on the appliance or accompanying documentation indicates that this product should not be disposed of as unsorted municipal waste but must be taken to a collection point for the treatment of WEEE. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local authority, the household waste disposal service or the shop where you purchased the product 96 Declaration of conformity • This cooktop is suitable for contact with foodstuffs and complies with EEC (CE) Regulation n. 1935/2004 • The appliances are designed solely for use as cooking appliances. Any other use of the appliances (e.g. for room heating) is considered as improper use and potentially dangerous. • The appliances are designed, built and sold in compliance with: • safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments). • the protection requirements of Directive 89/336/EEC pertaining to “Electromagnetic Compatibility”. • the requirements of Directive 93/68/EEC. 31902047GB.fm Page 97 Wednesday, May 21, 2008 6:28 PM PRECAUTIONS AND GENERAL ADVICE Warning: Accessible parts become very hot when the appliance is in operation. Keep children away from the appliance in order to avoid the risk of scalding and burns. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning use of the appliance by a person responsible for their safety. • Before any maintenance on the appliance, disconnect it from the electrical power supply. • Keep children away from the appliance when it is in use and also when it has been just switched off. • The appliances must be repaired or adjusted exclusively by a qualified technician. • Make sure that the electrical wires of other electrical appliances near the hob do not come into contact with hot parts. • the cooking zones will not switch on if pots and pans are not of the correct dimensions or cannot be magnetically detected. To check that pots and pans are made of ferrous material, use a magnet. If a pot or pan is removed from the cooking zone, it will switch off and a “U“ will appear on the display”. The cooking zone will remain off until another pot or pan is placed on it. • Do not switch on the hotplates/cooking zones when there is no pan in position. • Never clean the appliance with high pressure water or steam cleaning equipment. • If liquid spills or boils over, the hob may switch off: to enable it to be switched back on again, carefully dry the controls zone. • The hob features different size hotplates/ cooking zones. Use pots whose base diameter is the same as that of the hotplate/cooking zone. • Do not place metal objects such as knives, forks, spoons or lids on the hob surface since they can become very hot. To avoid permanently damaging the glass ceramic hob, do not use: - pots with bottoms that are not perfectly flat; - metal pots with enamelled bottom. • When finished cooking, press button . • Do not use the hob as a work surface or a support surface. • Do not leave the appliance unattended when frying food -risk of fire. • If the glass ceramic surface should break or crack to due violent impact (falling objects, etc.), disconnect the appliance from the mains and contact After-sales Service immediately. • Do not place food wrapped in aluminium foil, plastic containers or cloths on the hot cooking zones. • Do not drag pans across the glass ceramic surface - risk of scratches. • Avoid spilling sugar and similar substances on the hob. When necessary, clean the hob immediately following the care and maintenance instructions in this handbook. • If the hob is fitted with halogen lamps, do not stare at them when they are switched on. • Never heat canned foods on the hob without first having opened the can. HOB ACCESSORIES Child guard accessory AMH 122 This accessory can be obtained from the After-sales Service under Part N° 4819 310 18436. 97 31902047GB.fm Page 98 Wednesday, May 21, 2008 6:28 PM CARE AND MAINTENANCE OF THE GLASS CERAMIC HOB Clean the hob, when it is cool, after each use. This will prevent the build-up of dirt and make cleaning easier. Important: never clean the appliance with high pressure water or steam cleaning equipment. • Use a clean cloth, absorbent kitchen wipes and washing up liquid or a specific glass ceramic cleaner. • Remove baked-on dirt with the supplied scraper tool and specific cleaning products. • Food spills should be cleaned off before they bake onto the glass ceramic surface. • Foods with high sugar content (toffee, fruit juice, jam, etc.) that boil over while cooking, or spattered sugar stains must be immediately removed using a scraper. • Do not use abrasive products, bleach, oven-cleaner spray or pan scourers. The hob should be treated periodically with a proprietary brand of protective wax for glass ceramic hobs. Important Periodically check for dust under the appliance, near the cooling air inlet or the outlet openings. This could hinder the ventilation and cooling of the electronic module and decrease the effectiveness of the hob. TROUBLESHOOTING GUIDE hob not working • • • 1. 2. 98 When pressing the control buttons, did you follow the instructions in the section “Using the hob” in the enclosed ”Product Description Sheet”? Is there perhaps a power failure? Did you dry the hob carefully after cleaning it? If a cooking zone has been selected and an “F” or an “ER” appear on the display followed by a number, contact the After-sales Service and inform them of the “F” or “ER” on the display. - With the exception of the message “F03” or “ER03” that identifies the incorrect cleaning of the controls area. - To solve the problem follow the instruction in the ICleaning and maintenance of the glass ceramic hobI paragraph”. If one of the following codes is displayed when the hob On button is pressed: ER22, ER25, ER31, ER36, ER47, E2, E5, E6, E7, E9 contact the After-sales Service and inform them of the code displayed. 3. If the hob does not work following intensive use, the hob internal temperature is too high. Wait a few minutes until the hob cools down. The display shows the code “F21” or “ER21”. Important! If you are not able to turn the glass ceramic hob off after using it, disconnect it immediately from the power supply. 31902047GB.fm Page 99 Wednesday, May 21, 2008 6:28 PM AFTER-SALES SERVICE Before contacting After-sales Service 1. Try to solve the problem (see “Troubleshooting Guide”). 2. Turn off the appliance and switch it back on again to see if the fault persists. If after the above checks the fault persists, contact the nearest After-sales Service. If any repairs are required, please contact an authorized After-sales Service as indicated in the warranty. Failure to comply with these instructions may compromise the safety and quality of the product. Always specify: • a brief description of the fault; • the precise type and model of the appliances, • the service number (the number after the word “Service” on the data plate), located under the hob or on the Product Description Sheet. The service number is also indicated on the warranty booklet, • your complete address and phone number. 99
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project