Whirlpool ART 490 Instruction for UseAdd to my manuals
▼ Scroll to page 2 of 16
501960802030_GB 15-06-2007 15:27 Pagina 19 INSTRUCTIONS FOR USE BEFORE USING YOUR PRODUCT SAFEGUARDING THE ENVIRONMENT GENERAL PRECAUTIONS AND SUGGESTIONS INSTALLATION GENERAL DESCRIPTION OF PRODUCT OPERATION INTRODUCTION TO WINE USING THE WINE CELLAR COMPARTMENT USING THE FREEZER COMPARTMENT MAINTENANCE AND CLEANING TROUBLESHOOTING GUIDE AFTER-SALES SERVICE PRODUCT SHEET CONTROL PANEL REPLACING THE LAMP 19 501960802030_GB 15-06-2007 15:27 Pagina 20 BEFORE USING YOUR PRODUCT You have purchased a wine cellar (wine cooler) combined with a freezer. This appliance is intended for household use only. For best use of your appliance, please read these instructions carefully. In them you will find a description of the appliance and useful tips on keeping wines and food. Keep this booklet for future consultation. 1. After unpacking the appliance, make sure that it is not damaged and that the door closes properly. Inform your retailer of any damage within 24 hours. 2. Wait for at least two hours before switching the appliance on, so that the cooling circuit has time to reach full efficiency. 3. Make sure that the installation and electrical connection are carried out by a qualified engineer according to the manufacturer’s instructions and the local rules in force. 4. Clean the appliance before using it for the first time. SAFEGUARDING THE ENVIRONMENT 1. Packing The packing material is 100% recyclable and is labelled with the recycling symbol. Please dispose of all packing responsibly and carefully. Keep the packaging material (plastic bags, polystyrene parts, etc.) out of the reach of children because it is potentially hazardous. 2. Scrapping/Disposal The appliance has been made with recyclable material. This appliance is marked in conformity with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE). Making sure that it is scrapped correctly helps to prevent any adverse consequences for health and the environment. The symbol on the product, or on the documents accompanying this appliance indicates that this product should not be disposed of as household waste. Please dispose of this appliance at an Electrical & Electronic Equipment Collection point as in accordance with local environmental regulations for waste disposal. When it is scrapped, make it unusable by cutting the power cable and removing the doors and shelves so that children cannot access the inside easily. Scrap it according to the local rules for the disposal of waste and take it to a collection point. Do not leave it unattended even for a few days because it is a source of danger for children. For details of your local Collection Point please contact your Local Authority. 20 Information: This appliance does not use CFC. The refrigerant system contains either R134a (HFC) or R600 (HC). Refer to the rating plate inside the appliance. For appliances with Isobutane (R600a): isobutane is a natural gas which has no effect on the environment but is inflammable. Make sure that the cooling circuit pipes are not damaged. Declaration of conformity • This appliance is intended for storing food and is manufactured in conformity with European regulation(EC) No. 1935/2004. • This appliance has been designed, manufactured and sold in conformity with: - the safety objectives of Low Voltage Directive 2006/95/EC (replacing 73/23/EEC and subsequent amendments); - the protection requirements of the “EMC” 89/336/CEE Directive, modified by Directive 93/68/CEE. The appliance’s electrical safety is only assured when it is correctly connected to an efficient earthing system complying with legal provisions. 501960802030_GB 15-06-2007 15:27 Pagina 21 GENERAL PRECAUTIONS AND SUGGESTIONS • Use the wine cellar compartment for storing wines and the freezer compartment only for storing frozen food, freezing fresh food and for making ice cubes. • During installation, make sure the appliance does not damage the power cable. • Do not store glass containers with liquids in the freezer since they may burst. • Do not eat ice cubes or ice lollies immediately after taking them out of the freezer since they may cause cold burns • Before carrying out any maintenance or cleaning operation, unplug the appliance or disconnect it from the power supply. • Make sure the appliance is not near a heat source. • Do not store or use petrol, flammable liquids or gas in the vicinity of this or other electrical appliances. In fact, the fumes can cause fires or explosions. • To guarantee adequate ventilation, leave a space on both sides and above the appliance and follow the installation instructions. • Keep the appliance ventilation openings free. • All appliances equipped with an ice-maker and water dispenser must be connected to a water supply that only delivers drinking water (with mains water pressure of between 1,7 and 8,1 bars (25 and 117 PSI)). Ice-makers and/or water dispensers not directly connected to the water supply must be filled with drinking water only. • Install and level the appliance on a floor strong enough to take its weight and in a place suitable for its size and use. • For the water connection, use the pipe supplied with the new appliance; do not reuse that of the previous appliance. • The appliance must be handled and installed by two or more persons. • Install the appliance in a dry and wellventilated place. The appliance is arranged for use in places where the temperature comes within the following ranges, according to the climatic class given on the rating plate. The appliance may not work properly if it is left for a long period at a temperature above or below the specified range. Climatic Class SN N ST T Amb. T. (°C) from 10 to 32 from 16 to 32 from 16 to 38 from 16 to 43 Amb. T. (°F) from 50 to 90 from 61 to 90 from 61 to 100 from 61 to 110 • Be careful not to damage the floors (e.g. parquet) when moving the appliance. • Do not use mechanical, electric or chemical means other than those recommended by the Manufacturer to speed up the defrost process. • Do not damage the cooling system of the refrigerator. • Do not use or place electrical appliances inside the product if they are not of the type expressly authorised by the Manufacturer. • This appliance is not designed for use by young children or the infirm without supervision. • To avoid the risk of children becoming trapped and suffocating, do not allow them to play or hide inside the appliance. • Power cable modification or replacement must only be carried out by qualified personnel. • Do not use single/multi adapters or extension cords. • It must be possible to disconnect the appliance from the power supply by unplugging it or by means of a mains double-pole switch installed upstream of the socket. • Make sure the voltage specified on the rating plate corresponds to that of your home. • Do not swallow the contents (non-toxic) of the ice packs (in some models). • The Manufacturer declines any liability if the above advice and precautions are not respected. Important: • If large amounts of bottles are put in the appliance, it may take several days for it to reach a constant temperature. • The bottles can be stored neatly on the wooden racks. Each shelf can bear a maximum weight of 40 Kg. 21 501960802030_GB 15-06-2007 15:27 Pagina 22 GENERAL PRECAUTIONS AND SUGGESTIONS Remember when arranging • Place the bottles in a central position on the rack. • When closing the door make sure that the bottles do not touch the door. • Caution: highly concentrated alcohol must be kept hermetically closed and in a vertical position. • Because of the circulation of air in the refrigerator, different temperature zones form: The colder zones are those near the back wall, the warmer zones are close to the door. • Always store bottled wines individually and not in cases or cardboard boxes. • The wine cellar has a capacity of up to 50 X 0.75 lts bordeaux type bottles. The manufacturer shall not accept any liabilities whatsoever, should the above recommendations and precautions not be taken into consideration. INSTALLATION • Install the appliance away from heat sources. Direct exposure to the sun’s rays or placing the appliance near a heat source (radiators, cookers), increase power consumption and should be avoided. • When this is not possible, the following minimum separations should be respected: - 30 cm from coal or oil cookers; - 3 cm from electric and/or gas cookers. • Clean the inside (see the “Maintenance and cleaning” charter). • Insert or install the accessories/parts supplied. GENERAL DESCRIPTION OF PRODUCT OPERATION This appliance is a wine cellar combined with an electronically controlled freezer with star rating, and therefore allows separate adjustment of the temperature in the compartments. The freezer compartment enables perfect freezing of fresh and cooked food, the production of ice cubes and storing of frozen and deep-frozen food; defrosting is manual. The wine cellar compartment, equipped with automatic defrost, enables the storage of wines. “Vacation” option The electronic control allows the freezer compartment to be left on with the wine cellar compartment switched off. To activate this function, with all the appliance on, press the button (5) for 3 seconds until the wine cellar compartment display (7) goes off and the green light (6) comes on (“Vacation function”); the freezer display (4) will remain on. For technical reasons the freezer compartment cannot be switched off with only the wine cellar compartment switched on. 22 501960802030_GB 15-06-2007 15:27 Pagina 23 INTRODUCTION TO WINE Storing wine As is well known, wine will keep for a long time; if kept in a suitable place white wines will keep for about two years from the date of harvest, but should be drunk within a year. Light wines can instead be kept for up to two years, while some full-bodied red wines can keep for ten years and raisin wines even twenty years. When you buy a bottle of wine put it in the cellar or another suitable place immediately. Three factors are vital in the process which starts from the cultivation of the grape, through to ripening, harvesting and wine making: light, air humidity and room temperature. If the taste of the wine is to reach full maturity while maintaining the wine’s aroma, it must be stored perfectly by the interaction of these three factors. Storage space Not everyone has an underground storage space which can be used as a cellar. Just recently technology has managed to supply a valid substitute for the classic wine cellar. The Wine Cellar which you have purchased is a special appliance designed to contain and store wines correctly. In fact it should not be used to store fruit, vegetables and tins but only your favourite bottles of wine. So, without having a cellar area, every type of wine can be correctly stored, matured and enjoyed. Storage rules A vital rule for keeping your favourite bottles is that they should be placed on their sides or inclined so that the wine bathes the cork. Many people think that this causes the well-known “cork” smell. In reality contact between the wine and the cork helps the elasticity of the cork so guaranteeing its effectiveness. Being able to take the bottles easily for use avoids accidental shaking which, like vibration, could cause the sediments to suspend again, so altering the appearance of the wine over time. Move your bottles as little as possible and let the wine rest. Also avoid letting the bottles come into contact with the bottom wall because this would not only affect efficient defrosting but could ruin the bottle labels because of the drops of water collected during defrosting. The shelves on which the bottles are placed must be of wood, which efficiently absorbs any vibrations and keeps the bottle away from the wall which transmits the cold. The bottles of wine must also be kept away from substances or places which have a strong smell because this could easily be transmitted to the wine. The temperature The temperature represents a critical factor which is important throughout the wine’s life cycle. It determines wine’s good development while it remains in the bottle to mature. For best storage the temperature must be kept constant in an interval between 8 and 12°C. Rapid and wide changes of temperature must be avoided: too high a temperature dilates the liquids and speeds up the wine maturing, while too low a temperature (below 4 – 5°C) could cause the precipitation of tartrates, which could affect the wine’s appearance. In the extreme case in which the temperature drops below 0°C, the wine may freeze and cause the cork to be expelled. The cork The cork is a fundamental component of a bottle of wine: its quality, chosen by the wine producer, is very important for the maturation of the wine itself. The perfect condition of the cork, in the bottles which we buy, depends exclusively on the standards of use and storage used by the producer or bottler. 23 501960802030_GB 15-06-2007 15:27 Pagina 24 USING THE WINE CELLAR COMPARTMENT Wine cellar compartment defrosting is completely automatic. The appliance can operate at ambient temperatures of between +10°C and +38°C. Optimum performance depends on the climatic class indicated on the rating plate. Switching the appliance on and temperature adjustment. Switch on the power to the appliance. The ideal temperatures for preserving wines and foods are already factory-set. When the appliance is switched on for the first time, the acoustic signal sounds and the red light (10) flashes, indicating that the temperature inside the freezer is still not cold enough for introducing food. The acoustic signal can be deactivated by pressing the button (11) on the control panel. Place food in the freezer only when the red alarm light has gone off. Notes: • 4-5 hours are required for the wine cellar compartment to reach a suitable temperature for storage. • The ambient temperature, frequency of door opening and position of the appliance can affect the temperatures inside the two compartments. These factors should therefore be taken into account when setting temperatures. • The space between the shelves and the rear wall inside the refrigerator ensures the free circulation of air. • Do not place the bottles in direct contact with the rear wall of the wine cellar compartment. • Do not place hot food in the compartments. • Store liquids in closed containers. Temperature adjustment The temperature is factory-set to +10 °C (display 7). To change the temperature setting, press the buttons (8) or (9) on the control panel until obtaining the required value. The temperature will vary 2°C each time the buttons are pressed. Settable temperature limit: • +4 °C coldest temperature • +16 °C warmest temperature Switching off the wine cellar Press the button (5) for more than 3 seconds. The temperature shown on the display (7) goes off and the green light (6) comes on. To reactivate wine cellar operation, press the same button (5) again for more than 3 seconds. Wine cellar compartment alarms The acoustic alarm is activated when the door has been left open for more than 1 minute. If the door is left open for another minute, the inside light will start flashing and switches off 10 minutes after door opening, whereas the acoustic alarm will remain activated. Pressing the Acoustic Alarm button (11) will only silence the acoustic signal, whereas the inside light will continue to behave as described above. To completely deactivate the door open alarm, close the refrigerator door. To replace the lamp, refer to the product sheet. Control panel lock To avoid accidental selections (keys pressed by contact with packets and/or food, or by children) the control panel can be locked by pressing the keys (13) and (14) at the same time for 3 seconds; an acoustic signal will indicate activation of the function. With the “Control Panel Lock” function activated, the entire control panel will be locked except for the “alarm reset” key (11); an acoustic signal sounds and the message “CL” will appear on the freezer temperature display (4) whenever and for the entire time a key is pressed. To unlock the control panel proceed as above, pressing the keys (13) and (14) at the same time for 3 seconds. 24 501960802030_GB 15-06-2007 15:27 Pagina 25 USING THE FREEZER COMPARTMENT The freezer compartment has star rating. It can be used to store frozen foods for the period of time indicated on the food packaging. The freezer can also be used to freeze fresh food by positioning it on the racks; place already frozen food in the lower basket so that it is not in contact with food still to be frozen. The quantity of fresh food that can be frozen in 24 hours is given on the rating plate. Temperature adjustment The temperature is factory-set to -18°C (display 4). To change the temperature setting, press buttons (2) or (3) on the control panel until obtaining the required value. Settable temperature limit: • -17 °C least cold temperature • -24 °C coldest temperature Fast Freeze function. (also called: “Extra Load”, “Super” or “Fast Freezing”) Activate the fast freezing function by pressing the button (13) on the control panel 24 hours before placing a large amount of fresh food in the freezer; the food will then freeze in the quickest possible time. The function is activated when the yellow light (12) is on. The “Fast Freeze function” function is automatically deactivated after 48 hours. In any case, the function can be manually deactivated by pressing the same button again (the yellow light(12) goes off). Important • Wrap and seal the fresh food to be frozen in: aluminium foil, transparent film, waterproof plastic wrap, polyethylene containers with lids end suitable freezer containers. • Arrange the food to be frozen in the top drawer, leaving sufficient space around the packs for the air to circulate freely. Switching off the appliance Press the button (1) for 3 seconds. In this way the appliance switches off although remaining powered; the inside light and all the LEDs on the control panel go off except the Vacation light (6) and displays (4) and (7) which will show “- -” “- -”. To reactivate appliance operation, press the same button again for 3 seconds. 25 501960802030_GB 15-06-2007 15:27 Pagina 26 USING THE FREEZER COMPARTMENT Freezer compartment alarms Freezer compartment temperature alarm When the appliance is working or during the freezing phase, the red warning light (10) may come on in conjunction with an acoustic signal, indicating that the freezer compartment temperature is not optimum for food storage. This can occur in the following cases: • during start-up; • when the appliance is switched on again after defrosting and cleaning; • when too much food is placed in the freezer; • when the freezer door does not close properly. To deactivate the acoustic signal, press the button (11). The red light (10) will automatically go off when optimum temperature conditions are reached. Power failure alarm If a temperature value flashes in the freezer display (4), the acoustic signal sounds and the temperature adjustment keys are locked. This means that a power failure has occurred for a period long enough not to guarantee maintenance of the correct storage temperature. The value shown on the display gives the highest temperature reached by the freezer compartment. To eliminate the alarm and restore control panel operation, press the Acoustic Alarm button (11) and check the food, because the compartment temperature has risen above -9°C (temperature limit for correct food preservation). Note: The freezer compartment can maintain a suitable temperature for preserving food, even in case of a power failure. In any case, it is advisable to avoid opening the compartment door during such periods. Important: For frozen fresh food storage times, comply with the table opposite. When purchasing frozen food products: • Make sure the packaging is not damaged, since the food MONTHS can deteriorate. If the package is swollen or has damp patches, it has not been stored in optimum conditions and may have begun to thaw. 2-6 • Purchase frozen food last and use thermal bags to carry it. F • Place frozen foods in the freezer compartment as soon O as you get home. O • Do not refreeze partially thawed food; consume it D within 24 hours. • Avoid, or reduce temperature variations to the minimum. • Respect the expiry date given on the package. • Always follow the instructions given on the package for storing frozen foods. 26 4-8 6-12 501960802030_GB 15-06-2007 15:27 Pagina 27 USING THE FREEZER COMPARTMENT Removing the baskets Pull the drawers out as far as they go, then lift them slightly and remove. Note: The freezer can also be used without the drawers, in order to obtain a larger space; this is possible by removing them, leaving just the bottom one. Arrange food on the racks. After introducing the food make sure the freezer compartment door closes properly. Making ice cubes • Fill the ice cube tray up to 2/3 with water and place it in the freezer compartment. • Do not use sharp or pointed objects to detach the tray if it is stuck to the bottom of the freezer grill or drawers. • Bend the ice tray slightly to facilitate removal of the cubes. 27 501960802030_GB 15-06-2007 15:27 Pagina 28 MAINTENANCE AND CLEANING Cleaning the freezer compartment Before carrying out any cleaning or maintenance operation, switch the product off by pressing button (1) on the control panel for 3 seconds, then unplug the appliance or disconnect it from the power supply. The freezer should be defrosted once or twice a year, or when too much frost has formed on the refrigerant grills. It is perfectly normal for frost to form on the cooling grills. The amount and rate at which it accumulates depends on the room conditions and how often the door is opened, and tends to form more on the upper grills. It is advisable to defrost when the freezer is nearly empty. If possible, activate the “Fast Freeze” function 24 hours before defrosting, in order to thoroughly freezer the food; this helps to keep it cold whilst outside the freezer during defrosting process. 1. Open the freezer door and remove all the food, wrapping it close together in sheets of newspaper and put it in a very cool place or in a portable cooler. Leave the freezer door open to allow the frost to melt. 2. Pull out the defrost water drain and place a container under the drain. It is advisable to place a cloth in contact with the cabinet under the drain, to absorb any drops of water. 3. Clean the inside of the freezer with a sponge soaked in a solution of lukewarm water and/or mild detergent. Do not use abrasive substances. 4. Rinse and dry thoroughly. 5. Replace the defrost water drain in its position. 6. Close the freezer door. 7. Reconnect the appliance to the power supply and press the button (1) again for 3 seconds. An acoustic signal (temperature alarm) will sound; to deactivate it, press the button (11). When the red light (10) goes off put the food back in the freezer. Note: If the compartment is not used for prolonged periods, it is advisable to leave the freezer door open to prevent the formation of mould, odours and oxidation. 28 501960802030_GB 15-06-2007 15:27 Pagina 29 MAINTENANCE AND CLEANING Cleaning the wine cellar compartment Wine cellar compartment defrosting is completely automatic. Droplets of water on the rear wall inside the wine cellar compartment indicate that the automatic defrost phase is in progress. The defrost water is automatically run into a drain hole and collected in a container where evaporates. Clean the defrost water drain hole regularly using the tool supplied, in order to ensure the constant and correct flow of defrost water. To clean the wine cellar compartment: 1. Press the button (5) on the control panel for 3 seconds. 2. Empty the wine cellar compartment. 3. Clean the inside of the wine cellar with a sponge soaked in a solution of lukewarm water and/or mild detergent. Do not use abrasive substances. 4. Rinse and dry with a soft cloth. 5. Press the button (5) again for 3 seconds to restore wine cellar compartment operation. 6. Clean the oak wood rack with a damp cloth. Note: If the compartment is not used for prolonged periods, it is advisable to leave the refrigerator door open to prevent the formation of mould, odours and oxidation. 29 501960802030_GB 15-06-2007 15:27 Pagina 30 TROUBLESHOOTING GUIDE Before contacting the After-sales Service... Operation problems are often due to minor causes that can be found and fixed without using any tools. Noises from the appliance are normal, since the fans and compressors for controlling its operation switch on and off automatically. Some noises can be reduced by: • levelling the appliance and installing it on a flat surface • separating and preventing contact of the appliance with the cabinets • making sure the inside parts are correctly positioned • making sure the bottles and containers are not touching each other Some possible operation noises: • hissing when the appliance is switched on the first time or after a long period. • gurgling when the refrigerant enters the pipes. • humming when the water valve or fan are activated. • rattling when the compressor starts up or when the ice drips in the bucket. • a sudden thud when the compressor starts up or stops. When you hear these noises... ...your appliance is alive!!! 30 501960802030_GB 15-06-2007 15:27 Pagina 31 TROUBLESHOOTING GUIDE 1. The appliance does not work and the displays are off. • Is there a power failure? • Is the plug properly inserted in the socket? • Is the double-pole switch on? • Are the electric circuit safety devices installed in the house fully functional? • Is the power cable damaged? 2. The temperature inside the compartments is not cold enough. • Do the doors close properly? • Is the appliance installed near a heat source? • Is the temperature correctly set? • Is the air circulation through the ventilation grills at the bottom of the appliance obstructed? 3. There is water on the bottom of the wine cellar compartment. • Is the defrost water drain blocked? (refer to “Maintenance and cleaning”) 4. The inside light does not work. - Firstly check point 1, then: • Disconnect the appliance from the power supply. To access the lamp, refer to the instructions and diagram on the attached product sheet. • Check the lamp and, if necessary, replace it with a new one (max. 25 W, available only from the Aftersales Service ). 5. The red light on the control panel remains on and/or the acoustic alarm is activated. The light and alarm are activated for the following reasons: 1. Temperature alarm (red light on and acoustic signal activated) • Large amounts of fresh food have been recently placed in the freezer • The freezer door does not close properly (see the section “Using the freezing compartment") 2. Power failure alarm (red light on, acoustic signal activated and freezer display (4) flashing) • The appliance has undergone a power failure (refer to the section “Using the freezer compartment”) 3. “Faulty freezer sensor” alarm (red led on, acoustic signal activated and the letter C shown on the freezer display(4)) • The freezer compartment temperature sensor is faulty, but the appliance continues to work with an emergency procedure. Call the After-sales Service. 4. “Wine cellar sensors defective” alarm (red light on, acoustic signal activated and the letter C or E is shown on the refrigerator display (7)) • A refrigerator compartment temperature sensor is faulty, but the appliance continues to work with an emergency procedure. Call the After-sales Service. Notes: • If the front edge of the appliance is hot at the door seal edge, this is not a fault and prevents the formation of condensation. • If the temperature cannot be adjusted, make sure the “control panel lock” is not activated AFTER-SALES SERVICE Before contacting the After-sales Service: Switch the appliance on again to see if the problem has been eliminated. If it has not, switch off the appliance and repeat the operation after one hour. If your appliance still does not work properly after carrying out the checks listed in the troubleshooting guide and switching the appliance on again, contact the After-sales Service, clearly explaining the problem and specifying: • the appliance type and serial number (given on the rating plate). • the type of fault. • the model. • the Service number (the number after the word SERVICE on the rating plate inside the appliance). • your full address • your telephone number and area code. Note: If reversing of appliance door opening is carried out by the After-sales Service it is not covered by the warranty. 31 501960802030_GB 15-06-2007 15:27 Pagina 32 PRODUCT SHEET Carefully read the instructions before using the appliance. Red wine White wine Beer and sparkly wine A. Wine cellar compartment 1. Bottle storage shelves • Red wine area – (least cold area) • White wine area – (intermediate area) • Sparkly wine and beer – (coldest area) 2. Light unit (depending on the model) 3. Product control panel (depending on the model) 4. Rating plate (bottom of the cellar side wall) B. Freezer compartment 5. Upper basket (freezing area) 6. Frozen/deep frozen food storage compartment 7. Ice cube tray (inside basket) 8. Freezer compartment inner door Notes: The number of shelves and shape of the accessories may vary according to the model. All shelves can be removed. Caution: The refrigerator/freezer accessories must not be placed in a dishwasher. 32 501960802030_GB 15-06-2007 15:27 Pagina 33 CONTROL PANEL Freezer compartment 1. Appliance “On/Stand-by” button 2. Freezer temperature increase button 3. Freezer temperature decrease button 4. Freezer temperature display 12. “Extra” load function yellow light 13. “Extra” load function button (+ “Control panel lock” function) 10. Red warning light 11. Acoustic alarm deactivation button Wine cellar compartment 5. On/Stand-by wine cellar compartment button 6. Green On/Stand-by wine cellar compartment LED 7. Wine cellar compartment temperature display 8. Wine cellar temperature increase button 9. Wine cellar temperature decrease button 14. “Control panel lock” function button (Child lock) CONTROL PANEL LOCK The control panel can be locked after selecting the temperature of the refrigerator and freezer compartments. Press the keys (13) and (14) at the same time for at least 3 seconds and an acoustic alarm will signal activation of the function. With the “Control panel lock” function activated the entire control panel will remain locked except for the “alarm deactivation" key (11); if any key is pressed, an acoustic signal will sound and the message “CL” will appear on the freezer temperature display while the key is pressed. To unlock the control panel, proceed as above, pressing the buttons (13) and (14) at the same time for at least 3 seconds. Note: The ambient air temperature, frequency of door opening and position of the appliance can affect the temperatures inside the refrigerator and freezer compartments. Therefore these factors should therefore be taken into account when setting temperatures. REPLACING THE LAMP Always disconnect the refrigerator from the power supply before replacing any light bulbs. 1. Loosen the screw and remove the diffuser. 2. When replacing the lamp, remember that this appliance is fitted with a special lamp (max. 25W with bayonet connector, only available from the After-sales Service); to remove the lamp, pull it outwards as indicated by the arrow (do not unscrew it). 33 501960802030_GB 15-06-2007 15:27 Pagina 34 ELECTRICAL CONNECTION FOR GREAT BRITAIN AND IRELAND ONLY Warning - this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows: 1. Remove the fuse cover (A) and fuse (B). 2. Fit replacement 13A fuse into fuse cover. 3. Refit both into plug. Important: The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted. Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug. Replacement fuse covers are available from your local electrical store. For the Republic of Ireland only The information given in respect of Great Britain will frequently apply, but a third type of plug and socket is also used, the 2-pin, side earth type. 34 Socket outlet / plug (valid for both countries) If the fitted plug is not suitable for your socket outlet, please contact After-sales Service for further instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a qualified technician in compliance with the manufactures instructions and current standard safety regulations.
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project