Bauknecht ETPI 8540/IN Instructions for use

DEUTSCH
Installation
ENGLISH
Installation
FRANÇAIS
Installation
NEDERLANDS
Installatie
ESPAÑOL
Instalación
PORTUGUÊS
Instalação
ITALIANO
Installazione
ΕΛΛΗΝΙΚΑ
Εγκατάσταση
SVENSKA
Montering
NORSK
Installasjon
DANSK
Montering
SUOMI
Asennus
POLSKI
Instalacja
ČESKY
Instalace
SLOVENSKY
Inštalácia
MAGYAR
Üzembe helyezés
РУССКИЙ
Установка
БЪЛГАРСКИ
ROMÂNĂ
Seite
Page
Page
Pagina
Página
Página
Pagina
Σελίδα
Sidan
Side
Side
Sivu
Strona
Strana
Strana
Oldal
Стр.
7
16
25
35
45
54
63
72
82
90
100
109
118
127
137
146
155
Инсталиране Страница 165
Instalarea
Pagina 175
Bedienungsanleitung
Instructions for use
Mode d'emploi
Gebruiksaanwijzing
Instrucciones de uso
Instruções de utilização
Istruzioni per l’uso
Οδηγίες χρήσης
Bruksanvisning
Bruksanvisning
Brugervejledning
Käyttöohjeet
Instrukcja obsługi
Návod k použití
Návod na použitie
Használati utasítás
Инструкции по
зксплуатации
Инструкции за употреба
Instrucţiuni de utilizare
Seite
Page
Page
Pagina
Página
Página
Pagina
Σελίδα
Sidan
Side
Side
Sivu
Strona
Strana
Strana
Oldal
Стр.
8
17
26
36
46
55
64
73
83
92
101
110
119
128
138
147
156
Страница 166
Pagina 176
860 mm
840
mm
400 mm
832 mm
R = Min. 6,5 mm
Max. 8 mm
mm
+2
30
373 mm
0
-2
380 0 mm
+1
0
52 mm
A
B
R = Min. 6,5 mm
Max. 8 mm
0
750 +2 mm
Min. 50 mm
0
490 +2 mm
510 mm
+1
0
30 mm
52 mm
770 mm
483 mm
742 mm
0
773 +2 mm
R = 11,5 mm
Min. 50 mm
0
0
750+2
0
490+2 mm
mm
513 +2 mm
R = 11,5 mm
6 mm
R = Min. 6,5 mm
Max. 8 mm
2
Min. 10 cm
Min. 5 mm
Min. 5 mm
Min. 3 cm
Max. 6 cm
1
2
3
3
ENGLISH
Installation
Page
2
Instructions for use
Page
IMPORTANT SAFETY INFORMATION
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT
This manual and the appliance itself provide important safety messages, to be read and observed at all times.
This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.
All safety messages will follow the safety alert symbol and either the terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
All messages relevant to safety specify the potential risk to which they refer and
indicate how to reduce the risk of injury, damage and electric shocks due to
incorrect use of the appliance. Make sure to comply with the following:
- The appliance must be disconnected from the power supply before carrying out
any installation operation.
- Installation and maintenance must be carried out by a specialised technician, in
compliance with the manufacturer’s instructions and the local safety regulations
in force. Do not repair or replace any part of the appliance unless specifically
stated in the user manual.
- The appliance must be earthed.
- The power cable must be long enough for connecting the appliance, fitted in the
cabinet, to the power supply.
- For installation to comply with the current safety regulations, an omnipolar
switch with minimum contact gap of 3mm is required.
- Do not use multi-sockets or extension cords.
- Do not pull the appliance’s power cable.
- The electrical parts must not be accessible to the user after installation.
- The appliance is designed solely for domestic use for cooking food. No other use
is permitted (e.g. heating rooms). The Manufacturer declines any liability for
inappropriate use or incorrect setting of the controls.
- The appliance and its accessible parts become hot during use. Care should be
taken to avoid touching heating elements. Children less than 8 years old shall be
kept away unless continuously supervised.
- The accessible parts can become very hot during use. Children must be kept
away from the appliance and watched over to ensure they do not play with it.
- Do not touch the appliance heating elements during and after use. Do not allow
the appliance to come into contact with cloths or other flammable materials
until all the components have cooled sufficiently.
EN13
- Do not place flammable materials on or near the appliance.
- Overheated oils and fats catch fire easily. Pay attention when cooking food
products rich in fat and oil.
- This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
- A separator panel (not supplied) must be installed in the compartment under
the appliance.
- If the surface is cracked, switch off the appliance to avoid the possibility of
electric shock (only for appliances with glass surface).
- The appliance is not intended to be operated by means of an external timer or
separate remote control system.
- Unattended cooking on a hob with fat or oil can be dangerous and may result in
fire. NEVER try to extinguish a fire with water, but switch off the appliance and
then cover flame e.g. with a lid or a fire blanket.
Danger of fire: do not store items on the cooking surfaces.
- Do not use steam cleaners.
- Metallic objects such as knives, forks, spoons and lids should not be placed on
the hob surface since they can get hot.
- After use, switch off the hob element by its control and do not rely on the pan
detector (only for induction appliances).
EN14
SAFEGUARDING THE ENVIRONMENT
Disposal of packaging materials
The packaging material is entirely recyclable and marked with the recycling symbol ( ). Do not dispose of the various packaging materials carelessly, but do so
responsibly and in full compliance with local authority regulations governing waste disposal.
Scrapping
This appliance is marked in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).
By ensuring that this appliance is scrapped suitably, you can help prevent potentially damaging consequences for the environment and health.
The symbol
on the appliance or accompanying documentation indicates that this product should not be disposed of as unsorted municipal waste but must be taken
to a collection point for the treatment of WEEE.
Energy saving
For optimum results, observe the following advice:
• Use pots and pans whose bottom diameter is equal to that of the cooking zone.
• Only use flat-bottomed pots and pans.
• If possible, keep pot lids on when cooking (except for use in “SENSOR” mode).
• Cook vegetables, potatoes, etc. with little water in order to reduce cooking time.
• Use a pressure cooker to save even more energy and time (do not use pressure cookers with the “SENSOR” function).
• Make sure you place the pot or pan in the centre of the cooking zone outlined on the hob.
DECLARATION OF CONFORMITY
-
This appliance is designed to come into contact with food and complies with Regulation ( ) no. 1935/2004, and has been designed, constructed and marketed
in compliance with the safety requirements of “Low Voltage” Directive 2006/95/EC (replacing 73/23/EEC as amended) and protection requirements of “EMC”
Directive 2004/108/EC.
BEFORE USE
IMPORTANT: the cooking zones will not switch on if pots and pans are not of the correct dimensions. Only use pots bearing the symbol “INDUCTION
SYSTEM” (See figure opposite). Before switching the hob on, position the pot on the desired cooking zone.
EXISTING POTS AND PANS
OK
NO
Use a magnet to check whether pots or pans are suitable for use on the induction hob: pots are unsuitable if they cannot be magnetically detected.
- Ensure pots have a smooth bottom, otherwise they may scratch the hob's glass ceramic surface. Check dishes.
- Never place hot pots or pans on the hob's control panel. This could result in damage.
RECOMMENDED DIAMETERS OF POT BOTTOMS
XL
Ø
30 cm
14 cm
Ø
L
Ø
24 cm
17 cm
M
Ø
18 cm
14 cm
30 cm
XL
Ø
28 cm
18 cm
14 cm (Dual zone)
24 cm
L
Ø
21 cm
16 cm
S
Ø
14.5 cm
11 cm
Ø
Ø
18 cm
Ø
28 cm
Ø
21 cm
Ø
14.5 cm
IMPORTANT: Refer to the “SENSOR” section for correct pan base
diameters for cooking zones with SENSOR function.
28.5 x 18 cm
18 cm
24-28.5 cm
EN15
INSTALLATION
After unpacking the hob, check that there has been no damage during transport. If in doubt, contact the dealer or After-sales Service.
PREPARING THE HOUSING UNIT
-
Install a separator panel under the hob.
The lower part of the product must not be
accessible after installation.
If there is an oven beneath the hob, do not
install the seperator panel.
min. 5 mm
WARNING
min. 20 mm
min. 5 mm
•
•
•
•
•
For the distance between the underside of the appliance and the separator panel below, observe the dimensions given in the figure.
Do not obstruct the minimum required clearance between the hob and the top of the unit to ensure the correct operation of the product.
Cut the worktop to fit before installing the hob and carefully remove any shavings or sawdust.
In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit 4801 211 00112.
To remove the hob from the worktop use a screw driver (not supplied) unlocking the springs from the bottom side of the appliance.
ELECTRICAL CONNECTION
Disconnect the appliance from the mains power supply.
The appliance must be installed by a qualified technician who is fully aware of current safety and
installation regulations.
The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the
regulations provided in this chapter.
The power supply cable must be long enough to allow the hob to be removed from the worktop.
Make sure the voltage specified on the appliance rating plate is the same as that of the house electrical system.
Do not use extension leads.
WARNING
-
-
Connecting to the terminal board
For electrical connection, use an H05RR-F cable as specified in the table below.
3 x 4 mm2
230-240 V ~ +
3 X 4 mm2 (Australia only)
220-240 V 3 ~ +
4 X 1.5 mm2
380-415 V 3N ~ +
5 X 1.5 mm2
380-415 V 2N ~ +
4 X 1.5 mm2
380-415 V 2N ~
230-240 V ~ (Australia only)
220-240 V ~ (UK only)
220-240 V 3 ~ (Belgium only) 380-415 V 2N ~ (NL only)
230 V
230 V
C
230 V
230 V
B
230 V
230 V
A
220-240 V ~
230 V
220-240 V ~ +
380-415 V 3N ~
230 V
Amount x size
230 V
230 V
230 V
Conductors
Connect the yellow/green earth wire to the terminal with the symbol
.
This wire must be longer than the other wires.
1. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B).
2. Remove approx. 70 mm of sheath from the power supply cable.
3. Remove approx. 10 mm of sheath from the wires. Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in
the diagram next to the terminal board itself.
4. Secure the power cable with the cable clamp.
5. Close the cover (C) and screw it on the terminal block with the removed screw - point (1).
Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds.
If the hob already has a power cable, follow the instructions given on the label attached to the cable. Connect to the power mains using a multi-pole power switch with
a contact gap of at least 3 mm.
EN16
INSTRUCTIONS FOR USE
Control Panel Description
The control panel is equipped with touch controls: to use them, just press the corresponding symbol (it is not necessary to press hard).
To select and activate the cooking zones
To set the minute
counter
Hob ON/OFF
To enable the hold
function
To select one of the automatic functions
Slide touch screen
To lock the control panel
First use / after a power failure
After connecting the hob to the electrical power supply, the control panel is locked (the indicator light above the key is ON).
To unlock the control panel, press and hold the
key for 3 seconds. The indicator light switches off and the hob can be used normally.
Switching the hob ON/OFF
To switch the hob on, press and hold the
key for approx. 2 seconds: the indicator light above the key turns on and hyphens appear inside the cooking zone circles.
To switch off, press the same key until the hob switches off. All the cooking zones are switched off.
i
The hob automatically switches off if no function is selected within 10 seconds of switching on.
Switching on and adjusting cooking zones
Cooking zone selection and selected cooking zone/power level display
Indicates that one of the automatic functions is On
Cooking zone timer
Slide touchscreen (power adjustment)
After switching on the hob, position the pot on the chosen cooking zone.
Activate the cooking zone by pressing the relative round key: the round key displays number 5 that corresponds to the intermediate power level.
The hob automatically switches off if no function is selected within 10 seconds of switching on. If you are using a pot that is not suitable, not correctly
positioned or not of the correct dimensions for your induction hob, the message “no pot” will appear in the display (see figure on the left). If no pot is
detected within 60 seconds, the hob switches off.
To change the power level, move your finger horizontally on the slide touchscreen: the number inside the circle will change with just a quick slide of the finger from a
minimum of 1 to a maximum of 9. You can activate the booster function by pressing “BOOST” on the slide touchscreen (“P” on the display).
If more than one cooking zone is on, the slide touchscreen allows you to change the power level of the selected zone, indicated by the presence of a
luminous dot at the bottom right of the power level indicator. To select a zone, simply press the relative round key.
Switching off cooking zones
Select the cooking zone to be switched off by pressing the relative round key (a dot lights up at the bottom right of the power level indicator). Press OFF on the slide
touchscreen.
The cooking zone switches off and, if the zone is still hot, the letter “H” appears in the circle.
“H” is the residual heat indicator. The hob is fitted with a residual heat indicator for each cooking zone; these indicators alert the user when cooking
zones are still hot. When the cooking zone cools down, the display switches off.
EN17
Timer selection
The timer can be used to set a max. cooking time of 99 minutes.
Select the cooking zone to be used with the timer (a dot lights up at the bottom right of the power level indicator), then set the required cooking time using the + and
- keys of the timer function: the time in minutes is shown next to the cooking zone display.
A few seconds after the key is pressed, the timer begins the countdown (the luminous dot of the selected cooking zone starts flashing).
Once the set time has elapsed, an acoustic signal sounds and the cooking zone switches off automatically.
Control panel lock
This function locks the hob controls to prevent accidental switching on (e.g. during cleaning).
Press the
key for three seconds: an acoustic signal sounds and an indicator light turns on above the lock symbol to confirm activation. The control panel is locked
with the exception of the OFF function. To unlock the controls, repeat the child safety activation procedure. The illuminated dot switches off and the hob is active again.
IMPORTANT: The presence of water, liquid spilled from pots or objects of any nature resting on the key below the symbol can accidentally activate or deactivate the
Control panel lock function.
Hold
This function allows you to temporarily hold and then resume cooking processes maintaining previous settings (except for timer setting). Press the
on the display in place of the power levels. To resume cooking, press the
key:
blinks
key again.
Description of automatic functions
The hob features automatic functions for each cooking zone. The symbols of the available functions are shown next to the selection key of each cooking
zone. Every time an automatic function is selected, an indicator light turns on next to the symbol and the letter “A” appears in the cooking zone display.
Simmering
The simmering function automatically sets the selected cooking zone to a minimum boiling temperature. After positioning the pot, switch on the hob and select the
chosen cooking zone. Press the
key: “A” appears on the display and the indicator light turns on. To deactivate the function, simply press OFF on the slide
touchscreen.
Melting
This function maintains a permanently low temperature in the cooking zone. After positioning the pot/accessory on the chosen cooking zone, switch on the hob and
select the cooking zone. Press the
key: “A” appears on the display and the indicator light turns on. To deactivate the function, simply press OFF on the slide
touchscreen.
Sensor
The SENSOR function automatically selects the ideal power level to bring water to the boil and signals boiling point.
After positioning the pot of water, switch on the hob and select the desired cooking zone. Press the
key: “A” appears on the display and the indicator light turns
on. During heating, an animation is displayed in the space next to the cooking zone.
To ensure correct operation of the SENSOR function, we recommend that you:
Cooking zone Pan base diameter for Maximum amount
- use water only (at room temperature);
diameter
SENSOR function use of water in the pot
- do not add salt, other ingredients or condiments until the water reaches boiling
18 cm
17-19 cm
5 litres
point;
28 cm
24-28 cm
7 litres
- do not change the power setting of the cooking zone or remove or move the pot;
- do not use pressure cookers;
- fill the pot to at least 1/3 full (min. 1 litre) and never to the brim (see table on
the right).
For optimum results, observe the following advice:
- do not put the lid on the pot that is being used with the SENSOR function;
- do not activate the SENSOR function if the zone is already hot (letter “H” on the
display).
i
When the water comes to the boil, the hob emits an acoustic signal. This signal is sounded three times at regular intervals. After the second signal, a minute minder is
automatically activated to keep track of boiling time. After the third signal, the hob automatically selects a lower power setting to keep the water simmering. From this
moment on, you can add any ingredients you like, set the timer and change the power setting. Changing the power setting or selecting the “hold” function overrides
the SENSOR function.
The function is deactivated when the “hold” function is selected.
- The hob manages the SENSOR function and booster levels autonomously, therefore, in some cases, it may not be possible to activate the booster with
the SENSOR function already in use
- The quality of the cookware may affect the performance of the SENSOR function.
i
EN18
CLEANING
Never use steam cleaners.
Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H”) is
not displayed.
IMPORTANT: do not use abrasive sponges or pan scourers. as they could ruin the glass surface.
• Clean the hob, when it is cool, after each use in order to remove any food residues.
• Sugar and foods with a high sugar content damage the glass ceramic surface and must be immediately removed.
• Salt, sugar and sand can scratch the glass surface.
• Use a soft cloth, absorbent kitchen wipes or a specific hob cleaner (follow the Manufacturer's instructions).
WARNING
-
TROUBLESHOOTING GUIDE
•
•
•
•
•
Read and follow the instructions given in the section “Instructions for use”.
Connect the hob to the electricity supply and check that the supply has not been shut off.
Clean the hob and dry it thoroughly.
If you are unable to turn the hob off after using it, disconnect it from the power supply.
If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions.
ERROR CODE
DESCRIPTION
POSSIBLE CAUSES
The hob switches off and after 10 seconds Continuous pressure on control panel
emits an acoustic signal every 30 seconds. area.
C81, C82, C83
F42 or F43
Water or utensils on control panel.
The control panel switches off because The internal temperature of electronic
of excessively high temperatures.
parts is too high.
The connection voltage is wrong.
REMEDY
Clean the control panel.
Wait for the hob to cool down
before using it again.
The sensor detects a discrepancy
Disconnect the hob from the mains
between the appliance voltage and that and check the electrical connection.
of the mains supply.
F12, F21, F25, F36, F37, F40, F47, F56, F58, Call the After-sales Service and specify the error code.
F60, F61, F62, F63, F64
AFTER-SALES SERVICE
Before contacting After-sales Service
1. See if you can eliminate the problem on your own by referring to the “Troubleshooting guide”.
2. Turn the hob off and on again to check if the problem has been eliminated.
If after the above checks the fault persists, contact the nearest After-sales Service.
Always specify:
• a short description of the fault;
• the type and exact model of the hob;
• the Service number (the number after the word Service on the rating plate) located under the appliance (on the metal plate). The Service number is also
indicated on the warranty booklet;
• your full address;
• your telephone number and area code.
If any repairs are required, please contact an authorised After-Sales Service (to guarantee that original spare parts will be used and repairs carried out correctly).
EN19
POWER LEVEL TABLE
Power level
Max. power
Type of cooking
Boost
Fast heating
8-9
Frying - boiling
6-7
Browning - cooking - stewing Ideal for sautéing, maintaining a light boil, cooking and grilling (for a medium period of time,
- sautéing - grilling
10-20 minutes), preheating accessories
4-5
Cooking - stewing - sautéing Ideal for stewing, maintaining a gentle boil, cooking (for a long period of time). Creaming pasta
grilling
2-3
OFF
Ideal for browning, starting to cook, frying deep frozen products, fast boiling
Browning - sautéing - boiling Ideal for sautéing, maintaining a lively boil, cooking and grilling (for a short period of time,
- grilling
5-10 minutes)
3-4
Cooking - simmering thickening - creaming
1-2
Melting - thawing
1
Keeping food warm creaming
Zero
power
Support surface
Low power
Ideal for rapidly increasing the temperature of food to fast boiling in the case of water or rapidly
heating cooking liquids
7-8
High power
Medium power
Level use
(indicating cooking experience and habits)
Ideal for long-cooking recipes (rice, sauces, roasts, fish) with liquids (e.g. water, wines, broth,
milk), creaming pasta
Ideal for long-cooking recipes (quantities under 1 litre: rice, sauces, roasts, fish) with liquids (e.g.
water, wine, broth, milk)
Ideal for softening butter, gently melting chocolate, thawing small products
Ideal for keeping small portions of just-cooked food or serving dishes warm and for creaming
risotto
Hob in stand-by or off mode (possible end-of-cooking residual heat, indicated by an “H”)
Function
Description of function
Simmering
Identifies a power level that is suitable for simmering long-cooking recipes. Suitable for cooking tomato sauce, ragu, soups,
minestrone, maintaining a controlled cooking level (ideal for cooking in a bain-marie). Prevents food from boiling over or
sticking to the bottom and burning, as often happens with these recipes.
Melting
Identifies a power level that is suitable for slowly melting delicate products without compromising their sensorial quality
(chocolate, butter, etc.).
Sensor
Automatically identifies when water reaches boiling point and reduces the power to a level that maintains boiling until the
food is added. When the water reaches boiling point an acoustic signal is emitted, and any ingredients can be added (e.g.
condiments, pasta, rice, vegetables, meat and fish to be boiled) but also homemade preserves or accessories to be sterilized.
EN20
COOKING TABLE
Food
categories
Pasta, rice
Vegetables,
pulses
Meat
Fish
Eggs
Sauces
Desserts,
creams
Dishes or type
of cooking
Power level and cooking status
First stage
Power
Second stage
Power
Fresh pasta
Heating the water
Booster - 9
Cooking the pasta and
maintaining the boil
7-8
Dry pasta
Heating the water
Booster - 9
Cooking the pasta and
maintaining the boil
7-8
Boiled rice
Heating the water
Booster - 9
Cooking the pasta and
maintaining the boil
5-6
Risotto
Sautéing and roasting
7-8
Cooking
4-5
Boiled
Heating the water
Booster - 9
Boiling
6-7
Fried
Heating the oil
9
Frying
8-9
Sautéed
Heating the accessory
7-8
Cooking
6-7
Stewed
Heating the accessory
7-8
Cooking
3-4
Browned
Heating the accessory
7-8
Browning the soffritto
7-8
Roast
Browning the meat with oil (if with butter power level 6)
7-8
Cooking
3-4
Grilled
Preheating the grill
7-8
Grilling on both sides
7-8
Browned
Browning with oil (if with butter power level 6)
7-8
Cooking
4-5
Stewed
Browning with oil (if with butter power level 6)
7-8
Cooking
3-4
Grilled
Preheating the grill
7-8
Cooking
7-8
Stewed
Browning with oil (if with butter power level 6)
7-8
Cooking
3-4
Fried
Heating the oil or fatty matter
8-9
Frying
7-8
Frittata
Heating the pan with butter or fat matter
6
Cooking
6-7
Omelettes
Heating the pan with butter or fat matter
6
Cooking
5-6
Soft/hard-boiled
Heating the water
Booster - 9
Cooking
5-6
Pancakes
Heating the pan with butter
6
Cooking
6-7
Tomato
Browning with oil (if with butter power level 6)
6-7
Cooking
3-4
Ragu
Browning with oil (if with butter power level 6)
6-7
Cooking
3-4
Béchamel
Preparing the base (melt butter and flour)
5-6
Bring to a light boil
3-4
Pastry cream
Bring the milk to the boil
4-5
Maintain a light boil
4-5
Puddings
Bring the milk to the boil
4-5
Maintain a light boil
2-3
Rice in milk
Heat the milk
5-6
Cooking
2-3
EN21
5019 400 00200/A
DE GB FR NL ES
GR SE NO DK FI
SK HU RU BG RO
PT
PL
IT
CZ
Bauknecht® Registered trademark/TM Trademark of Whirlpool group of companies
11/12
© Copyright Bauknecht Hausgeräte GmbH 2012. All rights reserved