Whirlpool | AWZ8000 PRO | Instruction for Use | Whirlpool AWZ8000 PRO Instruction for Use

Machine operation
Additional information (including troubleshooting and service) can be found in the individual chapters of the
instructions for use.
Sort laundry according to
care symbols:
Do not tumble dry
Sort by:
Material thickness: Whenever there is greater load than the dryer can handle,
separate laundry according to weight (e.g. dry towels and thin underwear
separately).
Suitable for tumble drying at low drying temperature
Type of material: Cotton (linen); synthetic textiles (easy care).
Suitable for tumble drying
Do not tumble dry: Woollens, silk, nylon stockings, delicate embroidery, fabrics
with metallic decorations, bulky items such as sleeping bags, etc.
Preparing laundry
Check that all fastenings are closed and that pockets are empty. Please ensure that
there are no cigarette lighters in the wash. Turn laundry inside out.
Degree of drying: Cupboard dry, iron dry etc.
Opening door
Pull the door handle.
Loading dryer
Place laundry loosely in the drum to achieve equal drying throughout. Then close
the door.
Selecting programme
Select the drying programme required by turning the programme selector knob (for
information, refer to programme table).
Selecting options
(if available)
Select the option required by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection. A
fast blinking led indicates a wrong selection is made (incompatible options). Press
the button again to cancel the option.
Starting dryer
The drying programme is started by pressing the “Start (Pause)” button.
The relevant indicator lamp lights up.
Changing programme selection: If the programme selected is changed during
drying, the dryer stops. The “Start (Pause)” indicator lamp flashes. To operate the
new programme, again press the “Start (Pause)” button.
Interrupting programme: To interrupt a drying cycle, press the “Start (Pause)”
button and open the door. Wait at least 5 minutes, to allow the laundry to cool
down, before you unload the dryer. For your safety the drying cycle stops
automatically if you open the door. To restart, after door opening, close the door
and press the “Start (Pause)” button again.
Warning: Never stop a tumble dryer before the end of the drying cycle, unless all
items are quickly removed and spread out so that the heat is dissipated.
The final part of a tumble dryer cycle occurs without heat (cool down cycle) to
ensure that the items are left at a temperature that ensures that the items will not
be damaged.
Programme end unloading dryer
End: Take the laundry out of the dryer. The drying process is complete
and the anti-crease phase has been reached (active).
Anti-Crease: If the laundry is not removed at the end of the drying cycle,
an automatic anti-crease cycle will operate for maximum 15 min. The
drum rotates at regular intervals to prevent the laundry from creasing.
Set the programme selector knob to “Off” “
Switching dryer off
”.
Cleaning the lint filter: Open door, pull lint filter up and out of machine and open
it. Brush lint using a soft brush or your fingertips. Push lint filter firmly back into
place.
For your safety: Only use additives/plastic items specified as dryer safe. Rinsed items that have been treated with stain remover
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
1
X
1.0
4.0
Laundry which requires ironing such as:
trousers, dresses, skirts, shirts, blouses.
IRON DRY
X
1.0
4.0
Laundry which does not require ironing
such as: shirts, blouses, T-shirts, sportswear.
X
1.0
4.0
Laundry with thick, multi-layered areas:
CUPBOARD DRY PLUS bed and table linen, track suits, blankets.
CUPBOARD DRY
X
1.0
4.0
Laundry with thick, multi-layered areas:
bed and table linen, track suits, blankets.
EXTRA DRY
Max. 4 kg
Low temperature
X
3.0
8.0
Laundry which requires ironing such as:
bed and table linen, dry towels, T-shirts,
polo shirts, work clothes.
X
IRON DRY
3.0
8.0
CUPBOARD DRY
X
X
Gentle
Similar types of laundry which do not
require ironing such as: dry towels, bed
linen, underwear, baby clothes, T-shirts,
cotton socks.
Max. 8 kg
3.0
8.0
Normal temperature
Multi-layered, thick laundry such as: terry
CUPBOARD DRY PLUS towels, dish cloths and dry towels, bed linen,
underwear, terry towelling bath robes.
EXTRA DRY
3.0
8.0
Volume
of load
in kg
Multi-layered, thick laundry such as: terry
towels, dish cloths and dry towels, bed linen,
underwear, terry towelling bath robes.
Drying level
PROGRAMME OVERVIEW
X
X
X
X
X
X
X
X
Buzzer
OPTIONS
X
X
X
X
X
X
X
X
Start
delay
15’
55’
20’
60’
25’
70’
25’
75’
50’
125’
70’
150’
80’
165’
85’
180’
Very
wet
load
10’
50’
15’
55’
20’
60’
25’
60’
45’
100’
50’
125’
60’
140’
70’
160’
Wet
load
Approximate
drying times
(in minutes)
2
How to proceed if ...
Clean the filter at the end
...you want to correctly of every cycle.
care for and clean your
dryer:
• Open the door.
• Pull the filter upwards.
• Brush lint using a soft brush or your
fingertips.
• Push the filter back into place.
Please de-install once a
year the air hose and
remove the lint inside.
Drying takes too long
laundry is not dry enough.
• Has the correct drying programme
been selected?
• Was the inserted laundry too wet
(washing machine spin speed less than
1000 rpm?)
• Is the lint filter dirty (filter indicator
light on)?
• Is the room temperature too high?
• Are the “End” “
” and “Anticrease”
“
” indicator lamps lighting up? The
drying cycle is complete and the
laundry can be taken out.
• If the drying result does not meet your
expectation, select a more dry
programme.
The dryer will not operate
(after a power failure,
always press the “Start
(Pause)” button).
• Is the plug properly inserted into the
mains electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door properly closed?
• Has a drying programme been
selected?
• Has the “Start (Pause)” button been
pressed?
• Has the start delay option been
selected ?
• Is the dryer overloaded? Please remove
a part of the load.
Lint filter indicator lamp
on.
• Is the lint filter clean?
• Is the vent hose blocked?
• Is the outside vent hose adaptor blocked?
...you want to check the
dryer yourself first:
(If your machine is not
functioning correctly, please
check the following points
before phoning for the
customer service – also refer
to relevant chapter in the
instructions for use).
AFTER-SALES SERVICE
If the fault is still present once the above checks have been undertaken or should the fault occur for a second time, switch
the machine off. Please contact your after-sales service representative (for more information, refer to the warranty manual).
Please have the following details ready when calling your after-sales service representative:
• The nature of the fault.
• The dryer type and model.
• The service code (the number after the word Service on the
adhesive rating plate) on the right-hand side when the door is open.
3
Before using the machine, please also read the instructions for use carefully!
AWZ 8000/PRO
GB
Quick Reference Guide
Programme selector knob
The drying programme is selected by
turning this knob.
“Start (Pause)” button
The drying programme is started by
pressing this button. The indicator lamp
flashes during the selection phase and
lights up during drying.
Indicator lamps
Filter
The indicator lamp lights up when the
filter needs cleaning.
Clean the filter at the end of every
cycle.
Overdry protection
The indicator lamp lights up when a
humidity controlled program is selected,
to indicate the working protection
function. Function is not active in time
controlled programmes 20’, 30’, 40’,
60’, 90’ and “Airing” “ ”.
Whirlpool is a registered trademark of Whirlpool USA
Programme sequence
Overdry
protection
Drying
Anticrease
End
of cycle
Options
Gentle
Reduces drying intensity
(recommended for delicate items).
Buzzer
Signals/sounds end of drying cycle.
Delayed Start
Delays the start of the drying cycle by
3 to 9 hours. Each time the button is
pressed, the start time is delayed by 3
hours.
Then press the “Start (Pause)”
button to confirm the final selection
and to start the dryer. The delayed
start indicator lamp flashes and the
countdown counts down in 1-hour
intervals. The countdown is indicated
by the indicator lamp. During the
countdown, the drum will turn from
time to time to re-distribute the
laundry. To cancel or change the
previously set time delay, set the
programme selector knob to “Off”
“ ” or open the door.
5019 307 01424
(Subject to technical modifications)
4
Failure codes
In case of a malfunction of the appliance, a failure indication is shown or some LED lights
are blinking: (depending on the dryer model you have, the failure is displayed in letters or by
different layouts of blinking LED lights)
Message displayed
Check needed by customer before Service call
F02
Turn OFF the dryer. Unplug the dryer for more than 3 seconds.
Plug the dryer and start a new cycle with humid laundry. If the
problem persists, please call Customer Service.
F05
Turn OFF the dryer. Unplug the dryer for more than 3 seconds.
Clean the lint filter. Check if the ambient temperature is more than
5°C. Plug the dryer. Start a new cycle with humid laundry. If the
problem persists, please call Customer Service.
F06
Turn OFF the dryer. Unplug the dryer. Empty the bottle. Clean the
fluff filter. Plug the dryer. Start a new cycle with humid laundry. If
the problem persists, please call Customer Service.
F13
Turn OFF the dryer. Remove the load. Start the cycle again. If the
cycle starts, the dryer was overloaded. Stop the dryer and re-load
it again with half amount of laundry. If the failure indication occurs
again, please call Customer Service.
F14
Turn OFF the dryer. Unplug the dryer. Call the Customer Service.
F15
Turn OFF the dryer. Turn ON the dryer and restart the same
programme as before. If the same failure occurs again, turn OFF
the dryer. Unplug the dryer. Call the Customer Service.
LED is not blinking
LED is on or blinking
AFTER-SALES SERVICE
If the fault is still present once the above checks have been undertaken or should the fault occur for a second
time, switch the machine off. Please contact your After-Sales service representative (for more information, refer
to the warranty manual).
Please, have the following details ready when calling your after-sales service representative:
• The nature of the fault.
• The dryer type and model.
• The service code (the number after the word Service on the adhesive rating plate) on the right-hand side
when the door is open.
If the dryer appears damaged or defective, unplug the appliance and contact the machine owner for contacting
our After-Sales Service.
5
Download PDF

advertising