AEG | DD9663-M | User manual | Aeg DD9693-M User Manual

DD9663-M UK
DD9693-M UK
Cooker Hood
Operating and Installation Instructions
Thank you for buying an AEG product.
To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the
appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on AEG Products, please contact our Customer Services Department. For general enquiries concerning your
AEG appliance or for further information, visit our website at http:\\www.aeg.co.uk
Customer Services Department
Major Appliances
AEG
Addington Way
Luton
Bedfordshire LU4 9QQ Tel: 08705 350 350(*)
* calls to this number may be recorded for training purposes.
For the User
For the Installer
Important Safety Information
Installation Instructions
Technical Information
Your Appliance
Electrical Connections
Electrical Requirements
Electrical Connection
Operating Instructions
Cooker Hood Controls
To Operate
Recirculation
Extraction
Installing the Cooker Hood
Installation Requirements
Unpacking
Clearance Height
Wall drilling and bracket fi xing
Hood body mounting
Drilling the Shelves
Chimney assembly
Top Shelf
Maintenance and Cleaning
External Cleaning
Metal Grease Filter
To Remove the Grease Filter Cassette
Charcoal Filter
To Remove/Replace the Charcoal Filter
Worktop Lighting
Replacing the Light Bulb
Electrical Connection and Working Test
Something Not Working
Service and Spare Parts
Guarantee Conditions
Guide to use the instruction book
The following Symbols will be found in the text to guide you through the instruction book
Safety instructions
Step by step instructions
2
IMPORTANT SAFETY INFORMATION
These warnings are provided in the interests of your safety. Ensure that you understand them all before installing
or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings
of these warnings contact the Customer Services Department.
Installation
• Any installation work must be undertaken by a qualified electrician or competent person.
• This hood must be installed in accordance with the
installation instructions and all measurements adhered
to.
• If the cooker hood is installed for use above a gas
appliance then the provision for ventilation must be
in accordance with the Gas Safety Code of Practice
BS.6172, BS.5440 and BS.6891 (natural gas) and
BS.5482 (LP gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by
the Dept. of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the
Scottish Development Department.
• The fan motor of the cooker hood incorporates a
cut-out device, which will operate if the cooker hood
is installed below the minimum height recommended
in the Technical Information section, or if the motor
becomes overheated. If the cut-out device is activated, switch off the motor and allow the hood to
cool. The cut-out device will reset itself when the
fan motor has cooled.
• It is dangerous to alter the specifications or modify
this product in any way.
• When installed between adjoining wall cabinets, the
cabinets must not overhang the hob.
• If the room where the hood is to be used contains
a fuel burning appliance such as a central heating
boiler then its flue must be of the room sealed or
balanced flue type.
• If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the
room.
• When the hood is used in conjunction with appliances
supplied with energy other than electricity, the negative pressure in the room must not exceed 0.04mbar
to prevent fumes being drawn back into the room by
the hood.
• The ducting system for this appliance must not be
connected to any existing ventilation system which
is being used for any other purpose.
• Do not install above a cooker with a high level
grill.
During Use
• This appliance is for domestic use only.
• Never leave frying pans unattended during use as
over-heated fats and oils might catch fire.
• Never do flambé cooking under this cooker hood.
• Do not leave naked flames under this hood.
Maintenance and Service
• This appliance can be a fire hazard if the grease
and charcoal filters are not cleaned or replaced as
recommended.
• Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Force
Centre. Always insist on genuine spare parts.
Child Safety
• The appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the appliance.
3
YOUR APPLIANCE
4
OPERATING INSTRUCTIONS
This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam.
Key
A
B
C
D
E
F
G
H
Function
Turns the Lighting System on and off.
Turns the Motor on and off.
Activates speed one.
Activates speed two.
Activates speed three.
Activates intensive speed from any other speed, including
motor off. This speed is timed to run for 5 minutes, after
which the system will return to the speed that was previously set. Suitable to deal with severe cooking fumes.It is
deactivated by pressing the button or turning the motor off.
Activates delayed automatic shutdown of the motor and
the lighting system after 10’ if speed three is set, after 15’ if
speed two is set, and after 30’ if speed one is set. Suitable to
complete the elimination of residual odours, it is deactivated by pressing the button of turning the motor off.
Display
On or Off
On or Off
On.
On.
On.
On.
Enables Keyboard Lock mode if pressed and held for 5
seconds.
All the Leds flash twice and during Keyboard Lock the Leds light up in sequence.
It is disabled by pressing the button for 5 seconds.
Performs a Reset of the Filter saturation alarm when the
button is pressed for approximately 2 seconds with the
hood turned off.
All the Leds flash once.
After 100 hours operation the Led lights up
continuously to indicate saturation of the
Metal Grease Filters.After 200 hours operation the Led flashes to indicate saturation of
the Activated Charcoal Filters.
If pressed and held for 5 seconds with the hood turned off,
it:
enables the Activated Charcoal Filter Alarm.
disables the Activated Charcoal Filter Alarm.
5
On.
2 Flashes
1 Flash
OPERATING INSTRUCTIONS
This cooker hood can be used to recirculate or extract
contaminated air.
Recirculation Mode
The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted.
The contaminated air is cleaned by passing through the
filters and than back into the kitchen.
����
���
The activated charcoal filter absorbs odours arising from
cooking. In use it will slowly become saturated in grease
and less effective. The filter normally requires changing
after at least every three months or more frequently if the
hood is used for more than three hours per day.
• Insert the connection extension pieces laterally 14.1
in connec-tion 15.
• Insert the Connector 15 into the Support bracket 7.3
and fix it with a screw.
• Make sure that the outlet of the extension pieces
14.1 is hori-zontally and vertically aligned with the
chimney outlets.
• Connect the air outlet connection 15 to the hood
body outlet using either a flexible or rigid pipe ø
150 mm, the choice of which is left to the installer.
• Ensure that the activated charcoal filters have been
inserted.
��
�����
Fitting the Ducting
• To install the Ducting Version of the hood, the optional
Ducting chimney kit must be purchased.
Extraction (Ducted)
The cooker hood is more effective when installed in the
extraction mode (ducted to the outside).
Venting kits may be purchased through your retailer or DIY
store, and must be evacuated through an outside vent of
ø125 (5ins) or ø150mm (6ins).
The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard
or DIN 4102-B1.
When the cooker hood is ducted to the outside the
charcoal filter must be removed.
When installing the ducted version, connect the hood to
the chimney using either a flexible or rigid pipe ø 150 or
125mm, the choice of which is left to the installer.
To install a ø 150
• Fix the pipe in position using sufficient pipe clamps (not supplied).
To install a ø 120
• To install a ø 120 mm air exhaust connection, insert the reducer flange 9 .
• Fix the pipe in position using sufficient pipe clamps (not supplied).
• Remove any activated charcoal filters.
Never do flambé cooking under this cooker
hood.
Take extra care when frying and never leave
frying pans unattended during use, as overheated fats and oils can catch fire.
Do not leave naked flames under the cooker
hood.
Ensure the hood is switched on before using the
hob.
Ensure heating areas on your hob are covered
with pots and pans when using the hob and
cooker hood simultaneously.
Ensure not to damage the charcoal filter when
cleaning or replacing as the activated charcoal
inside is saturated with grease, which will stain if
it comes into contact with clothing or furnishings.
�����
�����
�
6
MAINTENANCE AND CLEANING
Before carrying out any maintenance or leaning isolate the cooker hood from the mains
supply.
The cooker hood must be kept clean, as a
build up of grease or fat can be a fire hazard.
External Cleaning
The metal casing, grille and chimney should be cleaned at
least once a month to keep it looking like new. Wipe over
the hood with a soft cloth wrung out in mild
soapy water and then dry thoroughly.
Never use scouring pads or abrasive cleaners as they
may scratch or damage the surfaces.
Always wear protective gloves when cleaning
the hood.
Never use scouring pads or abrasive cleaners.
Never use excessive amounts of water when
cleaning particularly around the control panel.
Metal Grease Filters
Filters can be washed in the dish machine. They need to
be washed when Drop-sign appears on the display or in
any case every 2 months, or even more frequently in case
of particularly intensive use of the hood.
To Remove the Grease Filter
• These filters can be washed in a dishwasher, and
need to be cleaned when the Led on Button H lights
up in a continuous manner or at least once every
approximately two months’ use, or more frequently
in the case of particularly intensive use.
Alarm reset
• Turn the Lights and the Suction motor off.
• Press button H and hold for at least 2 seconds,
confirmation is provided by the fact that the Led goes
out.
Cleaning the filters
• Remove the Filters one at a time, supporting them
with one hand while you pull the lever down with the
other.
• Wash the Filters without bending them, and leave
them to dry before replacing them.
• Replace the filters, taking care to ensure that the
handle is fac-ing outwards.
7
MAINTENANCE AND CLEANING
Alarm signal reset
• Turn the Lights and the Suction motor off.
• Press button H and hold for at least 2 seconds,
confirmation is provided by the fact that the Led goes
out.
Before carrying out any maintenance or
cleaning isolate the cooker hood from the
mains supply.
Charcoal Filters
In the recirculation mode the charcoal filters absorb smells
and unwanted odours.
This filter cannot be washed or regenerated, and must be
replaced when the Led on Button H starts to flash, or at
least every 4 months. The alarm can only be seen when
the Suction motor is turned on.
Enabling/Disabling the alarm signal
• For Recirculation Version Hoods, the Filter satura
tion alarm must be enabled on installation or at a later date.
• Turn the Lights and the Suction motor off.
• Press button H and hold for at least 5 seconds until the Led gives confirmation as follows:
• Led flashes twice - Activated Charcoal Filter Alarm ENABLED.
• Led flashes once - Activated Charcoal Filter Alarm DISABLED.
To Remove the Charcoal Filters
• Open the glass panel on the hood by pulling downwards.
• Remove the saturated activated charcoal filters as
shown (A).
• Fit the new filters, as indicated (B).
• Close the glass panel.
B
This appliance can be a possible fire hazard if
the grease and charcoal filters are not cleaned
and replaced as recommended.
8
A
MAINTENANCE AND CLEANING
Changing the Halogen Spot Lamp
• Extract the lamp from the lamp holder by pulling
gently.
• Replace with another of the same type, making sure
that the two pins are properly inserted in the lamp
holder socket holes.
Replacement filters and light bulbs can be
obtained from your local Service Force Centre.
9
SOMETHING NOT WORKING
If, having followed these instructions carefully, your cooker hood fails to work properly please carry out
the following checks.
Symptom
Solution
The cooker hood will not start
• Check the hood is connected to the electricity supply.
• Check that the fan speed control is set to 1, 2 or 3.
The cooker hood is not working effectively
• The fan speed is set high enough for the task.
• The grease filter is clean.
• The kitchen is adequately vented to allow the entry
of fresh air.
• If set up for recirculation, check that the charcoal
filter is still effective.
• If set up for extraction, check that the ducting and
outlets are not blocked.
The cooker hood has switched off during operation
• The safety cut-out device has been tripped.
• Turn off the hob and then wait for the device to reset.
I
In-guarantee customers should ensure
that the above checks have been made as
the engineer will make a charge if the fault
is not a mechanical or electrical
breakdown.
f after all these checks, the problem persists, contact
your local Service Force Centre, quoting the model and
serial number.
Please note that it will be necessary to provide proof of
purchase for any in-guarantee service calls.
SERVICE AND SPARE PARTS
If you require an engineer or wish to purchase spare parts
contact your local Service Force Centre by telephoning:
For general enquires concerning your AEG appliance or
for further information on AEG products, please contact
our Customer Services Department at the address below
or visit our website at www.aeg.co.uk
08705 929929
Your telephone call will be routed to the Service Force
Centre covering your postcode area.
Customer Services Department
Major Appliances
AEG
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 350 350 *
* calls to this number may be recorded for training purposes
10
GUARANTEE CONDITIONS
Standard Guarantee Conditions
We, AEG, undertake that if within 12 months of the date of the purchase this AEG built-in appliance or any part thereof
is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option, repair or
replace the same FREE OF ANY CHARGE for labour, materials and carriage on condition that:
• The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.
• The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
operating and maintenance instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
• All service work under this guarantee must be undertaken by an AEG Service Force Centre.
• Any appliances or defective parts replaced shall become the property of this company.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in
which case a premium will be charged.
EXCLUSIONS
This Guarantee does not cover:
• Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
• Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United
Kingdom.
• Appliances found to be in use within a commercial environment, plus those which are the subject of rental
agreements.
• Products of AEG manufacture which were not marketed by AEG. This guarantee is in addition to your statutory
and legal rights.
EUROPEAN GUARANTEE
If you move to another country within Europe then your guarantee moves with you to your new home subject to the
following qualifications:
• The guarantee starts from the date you first purchased your product.
• The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
• The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal
household.
• The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will ensure that the local Service organisation is aware of your move and able to look after
you and your appliance.
France
Germany
Italy
Sweden
UK
Senlis
Nurnberg
Pordenone
Stockholm
Luton
+33 (0)3 44 62 29 99
+49 (0)911 323 2600
+39 (0)01678 47053
+46 (0)8 738 79 50
+44 (0)8705 350 350
11
INSTALLATION INSTRUCTIONS
It is dangerous to alter the specifications or attempt to modify this product in any way.
Technical Information
DIMENSIONS HEIGHT (CANOPY): HEIGHT (CHIMNEY): WIDTH (CANOPY):
WIDTH (CHIMNEY): GROSS: NET:
270 mm
500-330 mm
698 - 898 mm
300 mm
26 kg - 28 kg
17 kg - 20 kg
ELECTRICAL SUPPLY: POWER CONSUMPTION:
FAN MOTOR: LAMP: (2x20W) HALOGEN LAMP
(3x20W) HALOGEN LAMP
220-240 V (50 Hz)
370 - 390 W
330 W
40 W
60 W
SUITABLE FOR INSTALLATION
ABOVE: ELECTRIC HOB: GAS HOB: SLOT-IN GAS COOKER SLOT-IN ELECTRIC COOKER 7 KW
10 KW
13.5 KW
12.4 KW
Note: CE Marking certifies that this appliance complies with the requirements laid
down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent
modifications and Low Voltage directive 72/23/E.
ELECTRICAL CONNECTIONS
This appliance must be earthed
Electrical Requirements
Any permanent electrical installation must comply with
the latest I.E.E. Regulations and local Electricity Board
regulations. For your own safety this should be undertaken
by a qualified electrician e.g. your local Electricity Board,
or a contractor who is on the roll of the National Inspection
Council for Electrical Installation Contracting (NICEIC).
This appliance is fitted with a 3 core mains cable and
must be permanently connected to the electricity supply
via a double-pole switch having 3mm minimum contact
gap on each pole. A Switched Fuse Connection Unit to
BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended
mains supply connection accessory to ensure compliance
with the Safety Requirements applicable to fixed wiring
instructions.
Electrical Connection
Before connecting to the mains supply ensure that the
mains voltage corresponds to the voltage on the rating
plate inside the cooker hood.
This appliance conforms to BS 800: 1988 and EEC
Directive No. 78 308 regarding suppression of radio and
television interference.
Remove the grease filters (see paragraph Maintenance)
being sure that the connector of the feeding cable is
correctly inserted in the socket placed on the side of
the fan.
12
INSTALLING THE COOKER HOOD
Please ensure that when the appliance is installed it
is easily accessible to an engineer in the event of a
breakdown.
All installations must comply with the local authorities requirements for the discharge of
exhaust air.
Incorrect installation may affect the safety of this
cooker hood.
Unpacking
Installation Requirements
2
1
Telescopic Chimney comprising:
2.1
1
Upper Section
2.2
1
Lower Section
9
1
Reducer Flange ø 150-120 mm
14.1
2
Air Outlet Connection Extension
15
1
Air Outlet Connection
Before unpacking the cooker hood position the carton with
the arrows pointing upwards as illustrated on the carton.
The canopy is supplied with the following components
for installation:
Ref. Q.ty Product Components
1
1 Hood Body, complete with: Controls, Light,
Blower, Filters
Before installation check the wall to
which the cooker hood is to be fitted for
electric cables, water pipes or gas.
The chimney hood must be installed according
to the instructions suppliers below and by qualified and competent personnel to the relevant
National Standards.
Ref. Q.ty Installation Components
7.2.1 2 Upper Chimney Section Fixing Brackets
The cooker hood is designed to be fixed to a solid block or
block wall over a cooking area. If not, suitable fixing must
be used for other types of walls. The hood can be used
in the extraction (ducted to the outside) or recirculation
(internal recycling) mode.
7.3
1
Air Outlet Connection Support
12c
6
Screws 2,9 x 9,5
The Installation work must be undertaken by a qualified
and competent person. The manufacturer disclaims any
responsibility to damages due to incorrect installation of
the cooker hood or if the cooker hood is not installed in
compliance with relevant regulations controlling this type
of installation.
Q.ty Documentation
1 Instruction Manual
�����
�
��
����
���
���
���
�
���
�
13
INSTALLATION INSTRUCTIONS
Wall drilling and bracket fixing
���
Wall marking:
• Draw a vertical line on the supporting wall up to the
ceiling, or as high as practical, at the centre of the
area in which the hood will be installed.
• Draw a horizontal line at 650 mm above the hob.
• Place bracket 7.2.1 on the wall as shown about 1-2
mm from the ceiling or upper limit align-ing the centre
(notch) with the vertical reference line.
• Mark the wall at the centres of the holes in the
bracket.
• Place bracket 7.2.1 on the wall as shown at X mm
below the first bracket (X = height of the upper
chimney section supplied), aligning the centre (notch)
with the vertical line.
• Mark the wall at the centres of the holes in the
bracket.
• Mark a reference point as indicated at 122 mm from
the vertical reference line and 280 mm above the
horizontal reference line.
• Repeat this operation on the other side.
• Drill ø 8 mm holes at all the centre points marked.
• Fix the lower bracket 7.2.1 using the screws.
• Fix the upper bracket 7.2.1 and the air outlet connection support 7.3 together using 2 screws.
• Insert the two screws in the hood body fixing holes,
leaving a gap of 5-6 mm between the wall and the
head of the screw.
�
�����
��������
���
��� ���
14
INSTALLATION INSTRUCTIONS
Hood body mounting
• Before attaching the hood body, tighten the two screws
Vr located on the hood body mounting points.
• Hook the hood body onto the screws.
• Fully tighten support screws.
• Adjust screws Vr to level the hood body.
��
���
���
Chimney assembly
���
Upper exhaust flue
• Slightly widen the two sides of the upper flue and
hook them behind the brackets 7.2.1, making sure
that they are well seated.
• Secure the sides to the brackets using the 4 screws
12c (2,9 x 9,5) supplied.
• Make sure that the outlet of the extensions pieces
is aligned with the chimney outlets.
�
���
���
���
Lower exhaust flue
• Slightly widen the two sides of the flue and hook
them between the upper flue and the wall, making sure that they are well seated.
• Fix the lower part laterally to the hood body using
the 2 screws 12c (2,9 x 9,5) supplied.
Electrical connection and working
test:
• Connect the hood to the mains supply.
• Open the upper panel by pressing the A-key (See
Part “USE” ) for at least 2 seconds.
• Remove the metal filters (See Part “MAINTENANCE”)
and make sure that the connector piece of the supply
cable is correctly inside the hood socket.
15
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste. Instead
it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling
of this product, please contact your local city office, your household waste disposal service or the shop where you purchased
the product.
436004092_02 - 080826
Download PDF

advertising