Aeg-Electrolux | DD9995-B | User manual | Aeg-Electrolux DD9995-B User Manual

DD9995-B
Cooker Hood
Operating and Installation Instructions
Thank you for buying an AEG product.
To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the
appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on AEG Products, please contact our Customer Services Department. For general enquiries concerning your
AEG appliance or for further information, visit our website at http:\\www.aeg.co.uk
Customer Services Department
Major Appliances
AEG
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel:
08705 350 350(*)
* calls to this number may be recorded for training purposes.
For the User
For the Installer
Important Safety Information
Installation Instructions
Technical Information
Your Appliance
Electrical Connections
Electrical Requirements
Electrical Connection
Operating Instructions
Cooker Hood Controls
To Operate
Recirculation
Extraction
Installing the Cooker Hood
Installation Requirements
Unpacking
Clearance Height
Wall drilling and bracket fi xing
Hood body mounting
Drilling the Shelves
Chimney assembly
Top Shelf
Maintenance and Cleaning
External Cleaning
Metal Grease Filter
To Remove the Grease Filter Cassette
Charcoal Filter
To Remove/Replace the Charcoal Filter
Worktop Lighting
Replacing the Light Bulb
Electrical Connection and Working Test
Something Not Working
Service and Spare Parts
Guarantee Conditions
Guide to use the instruction book
The following Symbols will be found in the text to guide you through the instruction book
Safety instructions
Step by step instructions
2
IMPORTANT SAFETY INFORMATION
These warnings are provided in the interests of your safety. Ensure that you understand them all before installing
or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings
of these warnings contact the Customer Services Department.
Installation
• Any installation work must be undertaken by a qualified electrician or competent person.
• This hood must be installed in accordance with the
installation instructions and all measurements adhered
to.
• If the cooker hood is installed for use above a gas
appliance then the provision for ventilation must be
in accordance with the Gas Safety Code of Practice
BS.6172, BS.5440 and BS.6891 (natural gas) and
BS.5482 (LP gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by
the Dept. of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the
Scottish Development Department.
• The fan motor of the cooker hood incorporates a
cut-out device, which will operate if the cooker hood
is installed below the minimum height recommended
in the Technical Information section, or if the motor
becomes overheated. If the cut-out device is activated, switch off the motor and allow the hood to
cool. The cut-out device will reset itself when the
fan motor has cooled.
• It is dangerous to alter the specifications or modify
this product in any way.
• When installed between adjoining wall cabinets, the
cabinets must not overhang the hob.
• If the room where the hood is to be used contains
a fuel burning appliance such as a central heating
boiler then its flue must be of the room sealed or
balanced flue type.
• If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the
room.
• When the hood is used in conjunction with appliances
supplied with energy other than electricity, the negative pressure in the room must not exceed 0.04mbar
to prevent fumes being drawn back into the room by
the hood.
• The ducting system for this appliance must not be
connected to any existing ventilation system which
is being used for any other purpose.
• Do not install above a cooker with a high level
grill.
During Use
• This appliance is for domestic use only.
• Never leave frying pans unattended during use as
over-heated fats and oils might catch fire.
• Never do flambé cooking under this cooker hood.
• Do not leave naked flames under this hood.
Maintenance and Service
• This appliance can be a fire hazard if the grease
and charcoal filters are not cleaned or replaced as
recommended.
• Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Force
Centre. Always insist on genuine spare parts.
Child Safety
• The appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the appliance.
3
YOUR APPLIANCE
4
OPERATING INSTRUCTIONS
This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam.
A
B
Key
A
B
C
D
E
F
G
H
I
L
C
D
F
E
Function
Upper panel closed: when pressed for about one sec-ond it
opens the upper panel. It switches the motor on at the latest
selected speed.Upper panel open: when shortly pressed it
switches the motor on/off.
Decreases the suction speed.
Increases the suction speed.
Functioning only when the upper panel is open. This speed
has been timed at 10 minutes. After that time the system activates automatically the latest selected speed. The function
is suitable for cooking conditions when vapours and smells
are of the utmost emission.
Functioning only when the upper panel is open. By pressing this key it is possible to set up the motor to a suction
speed at 100 m3/h .
Functioning only when the motor is on. By pressing this
key it is possible to set the delayed shutdown of the motor
and the lighting to 30 minutes.
By pressing this key for about 2 seconds it is possible to
reset the filter saturation alarm.
G
H
I
L
Display
Indicates the selected speed.
Number of lit LEDS decreases.
Number of lit LEDS increases.
I flashes and all the LEDS on the display
are lit.By pressing the key the function is
deacti-vated.
24–symbol appears and the LEDS on the
display go off cyclically, one by one. By
pressing the key the function is deactivated.
A flashing clock symbol appears. By pressing the key the function is deacti-vated.
A drop symbol indicates that the metal
grease filters saturation alarm has been
activated, and the filters need to be washed.
The alarm is triggered after 100 working
hours. C indicates that the charcoal filter
satura-tion alarm has been activated, and
the filter has to be replaced. The alarm s
triggered after 200 working hours.
By pressing this key the intensity of the lighting sys-tem
can be modified up to five levels.
Upper panel closed: when pressed for about 1 second
it opens the upper panel and sets the lights at the maximum intensity.Upper panel open: when shortly pressed it
switches the lights on/off.
Upper panel closed: when pressed for about one sec-ond
it opens the upper panel and switches the motor on at the
third speed and the lights at the maximum intensity.Upper
panel open: when pressed for about 1 second it switches
off motor and lights resetting every activated function, and
closes the upper panel.
Keyboard lock: it is possible to jam the keyboard when, for example, cleaning the glass. The motor and lights are
switched off, and upper panel can be open or closed.By pressing the F-key (Delay) for about 5 seconds the keyboard
block can be activated or de-activated. This function is confirmed by a Beep and by moving motor LEDS on display.
5
OPERATING INSTRUCTIONS
This cooker hood can be used to recirculate or extract
contaminated air.
Recirculation Mode
8
The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted.
The contaminated air is cleaned by passing through the
filters and than back into the kitchen.
12d
12c
16
The activated charcoal filter absorbs odours arising from
cooking. In use it will slowly become saturated in grease
and less effective. The filter normally requires changing
after at least every three months or more frequently if the
hood is used for more than three hours per day.
• Remove the chimney angle bracket.
• Screw the filter cover onto the air outlet, using four
screws 12c (2.9 x 12.5).
• Fix the air outlet grid 8 on the recirculation air outlet
using the 2 screws 12d (2,9 x 9,5) provided.
Fitting the Ducting
• To install the Ducting Version of the hood, the optional
Ducting chimney kit must be purchased.
Extraction (Ducted)
Never do flambé cooking under this cooker
hood.
Take extra care when frying and never leave
frying pans unattended during use, as overheated fats and oils can catch fire.
Do not leave naked flames under the cooker
hood.
Ensure the hood is switched on before using the
hob.
Ensure heating areas on your hob are covered
with pots and pans when using the hob and
cooker hood simultaneously.
Ensure not to damage the charcoal filter when
cleaning or replacing as the activated charcoal
inside is saturated with grease, which will stain if
it comes into contact with clothing or furnishings.
The cooker hood is more effective when installed in the
extraction mode (ducted to the outside).
Venting kits may be purchased through your retailer or DIY
store, and must be evacuated through an outside vent of
ø125 (5ins) or ø150mm (6ins).
The ducting used must be manufactured from fire retardent material conforming to the relevant British Standard
or DIN 4102-B1.
When the cooker hood is ducted to the outside the
charcoal filter must be removed.
When installing the ducted version, connect the hood to
the chimney using either a flexible or rigid pipe ø 150 or
125mm, the choice of which is left to the installer.
To install a ø 150
• To install the dumper 10
• Fix the pipe in position using sufficient pipe clamps
(not supplied).
To install a ø 120
• To install a ø 120 mm air exhaust connection, insert
the reducer flange 9 on the dumper 10.
• Fix the pipe in position using sufficient pipe clamps
(not supplied).
• Remove any activated charcoal filters.
ø 150
ø 120
9
10
10
6
MAINTENANCE AND CLEANING
Before carrying out any maintenance or leaning isolate the cooker hood from the mains
supply.
The cooker hood must be kept clean, as a
build up of grease or fat can be a fire hazard.
External Cleaning
The metal casing, grille and chimney should be cleaned at
least once a month to keep it looking like new. Wipe over
the hood with a soft cloth wrung out in mild
soapy water and then dry thoroughly.
Never use scouring pads or abrasive cleaners as they
may scratch or damage the surfaces.
Always wear protective gloves when cleaning
the hood.
Never use scouring pads or abrasive cleaners.
Never use excessive amounts of water when
cleaning particularly around the control panel.
Metal Grease Filters
Filters can be washed in the dish machine. They need to
be washed when Drop-sign appears on the display or in
any case every 2 months, or even more frequently in case
of particularly intensive use of the hood.
To Remove the Grease Filter
• Open the upper panel by pressing the A-key for 1
second (see Part USE).
• Remove the filters one by one pushing them towards
the back side of the hood unit and simultaneously
pulling downwards.
Alarm reset
• Press the G–key for at least 2 seconds.
Cleaning the filters
• Any kind of bending of the filters has to be avoided
when washing them. Before fitting them again into the
hood make sure that they are completely dry. (The
colour of the filter surface may change throughout
the time but this has no influence to the filter efficiency).
• When fitting the filters into the hood pay attention
that they are mounted in correct position the handle
facing outwards.
7
MAINTENANCE AND CLEANING
Alarm signal reset
• Stop the motor and switch off the lights.
• Press the G-key for at least 2 seconds.
Before carrying out any maintenance or
cleaning isolate the cooker hood from the
mains supply.
Charcoal Filters
In the recirculation mode the charcoal filters absorb smells
and unwanted odours.
This filter cannot be washed or regenerated. It must be
replaced when the C appears on the display or at least
once every 4 months. The filter saturation alarm has to
be activated already before.
Enabling/Disabling the alarm signal
• In the recycling version hoods the filter saturation
alarm must be activated during the instal-lation or
later.
• Switch off the hood and the lights.
• Press the E-key for about 5 seconds until the last
two segments of the motor LEDS are lit on the
display.
• By releasing the E-key the clock icon starts to
flash.
• Within 3 seconds press the D-key to activate/
deactivate charcoal filter saturation alarm.
• C-symbol lit - charcoal filter saturation alarm
ACTIVATED.
• C-symbol unlit - charcoal filter saturation alarm
DEACTIVATED.
To Remove the Charcoal Filters
• Open the upper panel by pressing the A-key for about
a second (see Part USE).
• Remove the metal filters.
• Remove the saturated charcoal filter as indicated
(A).
• Fit the new filters as indicated (B).
• Put the metal grease filters in their seats.
B
This appliance can be a possible fire hazard if
the grease and charcoal filters are not cleaned
and replaced as recommended.
8
A
MAINTENANCE AND CLEANING
Changing the Halogen Spot Lamp
• Extract the lamp from the lamp holder by pulling
gently.
• Replace with another of the same type, making sure
that the two pins are properly inserted in the lamp
holder socket holes.
Replacement filters and light bulbs can be
obtained from your local Service Force Centre.
9
SOMETHING NOT WORKING
If, having followed these instructions carefully, your cooker hood fails to work properly please carry out
the following checks.
Solution
Symptom
• Check the hood is connected to the electricity supply.
• Check that the fan speed control is set to 1, 2 or 3.
The cooker hood will not start
The cooker hood is not working effectively
• The fan speed is set high enough for the task.
• The grease filter is clean.
• The kitchen is adequately vented to allow the entry
of fresh air.
• If set up for recirculation, check that the charcoal
filter is still effective.
• If set up for extraction, check that the ducting and
outlets are not blocked.
• The safety cut-out device has been tripped.
• Turn off the hob and then wait for the device to reset.
The cooker hood has switched off during operation
I
In-guarantee customers should ensure
that the above checks have been made as
the engineer will make a charge if the fault
is not a mechanical or electrical
breakdown.
f after all these checks, the problem persists, contact
your local Service Force Centre, quoting the model and
serial number.
Please note that it will be necessary to provide proof of
purchase for any in-guarantee service calls.
SERVICE AND SPARE PARTS
If you require an engineer or wish to purchase spare parts
contact your local Service Force Centre by telephoning:
For general enquires concerning your AEG appliance or
for further information on AEG products, please contact
our Customer Services Department at the address below
or visit our website at www.aeg.co.uk
08705 929929
Your telephone call will be routed to the Service Force
Centre covering your postcode area.
Customer Services Department
Major Appliances
AEG
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 350 350 *
* calls to this number may be recorded for training purposes
10
GUARANTEE CONDITIONS
Standard Guarantee Conditions
We, AEG, undertake that if within 12 months of the date of the purchase this AEG built-in appliance or any part thereof
is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option, repair or
replace the same FREE OF ANY CHARGE for labour, materials and carriage on condition that:
• The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.
• The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
operating and maintenance instructions.
• The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
• All service work under this guarantee must be undertaken by an AEG Service Force Centre.
• Any appliances or defective parts replaced shall become the property of this company.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in
which case a premium will be charged.
EXCLUSIONS
This Guarantee does not cover:
• Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
• Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United
Kingdom.
• Appliances found to be in use within a commercial environment, plus those which are the subject of rental
agreements.
• Products of AEG manufacture which were not marketed by AEG. This guarantee is in addition to your statutory
and legal rights.
EUROPEAN GUARANTEE
If you move to another country within Europe then your guarantee moves with you to your new home subject to the
following qualifications:
• The guarantee starts from the date you first purchased your product.
• The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
• The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal
household.
• The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will ensure that the local Service organisation is aware of your move and able to look after
you and your appliance.
France
Germany
Italy
Sweden
UK
Senlis
Nurnberg
Pordenone
Stockholm
Luton
+33 (0)3 44 62 29 99
+49 (0)911 323 2600
+39 (0)01678 47053
+46 (0)8 738 79 50
+44 (0)8705 350 350
11
INSTALLATION INSTRUCTIONS
It is dangerous to alter the specifications or attempt to modify this product in any way.
Technical Information
DIMENSIONS
HEIGHT (CANOPY):
HEIGHT (CHIMNEY):
WIDTH (CANOPY):
WIDTH (CHIMNEY):
GROSS:
NET:
ELECTRICAL SUPPLY:
POWER CONSUMPTION:
FAN MOTOR:
LAMP:
(2x20W) HALOGEN Ø 35 mm GUA
SUITABLE FOR INSTALLATION
ABOVE:
ELECTRIC HOB:
GAS HOB:
SLOT-IN GAS COOKER
SLOT-IN ELECTRIC COOKER
730 mm
500-1000 mm
798 mm
Ø300 mm
43.8 kg
33,4 kg
220-240 V (50 Hz)
370 W
330 W
40 W
7 KW
10 KW
13.5 KW
12.4 KW
Note: CE Marking certifies that this appliance complies with the requirements laid
down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent
modifications and Low Voltage directive 72/23/E.
ELECTRICAL CONNECTIONS
This appliance must be earthed
Electrical Requirements
Any permanent electrical installation must comply with
the latest I.E.E. Regulations and local Electricity Board
regulations. For your own safety this should be undertaken
by a qualified electrician e.g. your local Electricity Board,
or a contractor who is on the roll of the National Inspection
Council for Electrical Installation Contracting (NICEIC).
This appliance is fitted with a 3 core mains cable and
must be permanently connected to the electricity supply
via a double-pole switch having 3mm minimum contact
gap on each pole. A Switched Fuse Connection Unit to
BS1363 Part 4, fitted with a 3 Amp fuse, is a recommended
mains supply connection accessory to ensure compliance
with the Safety Requirements applicable to fixed wiring
instructions.
Electrical Connection
Before connecting to the mains supply ensure that the
mains voltage corresponds to the voltage on the rating
plate inside the cooker hood.
This appliance conforms to BS 800: 1988 and EEC
Directive No. 78 308 regarding suppression of radio and
television interference.
Remove the grease filters (see paragraph Maintenance)
being sure that the connector of the feeding cable is
correctly inserted in the socket placed on the side of
the fan.
12
INSTALLING THE COOKER HOOD
Unpacking
Please ensure that when the appliance is installed it
is easily accessible to an engineer in the event of a
breakdown.
All installations must comply with the local
authorities requirements for the discharge of
exhaust air.
Incorrect installation may affect the safety of this
cooker hood.
Before unpacking the cooker hood position the carton with
the arrows pointing upwards as illustrated on the carton.
The canopy is supplied with the following components
for installation:
Ref Qty Product Components
1
1
Cooker hood with control unit, lights,
blower unit, filters
2.1
1
Upper chimney
2.2
1
Lower chimney
8
1
Air outlet grid
9
1
Reducer flange Ø 150-120
10
1
Damper
16
1
Cover for recycling version
Installation Requirements
Before installation check the wall to
which the cooker hood is to be fitted for
electric cables, water pipes or gas.
The chimney hood must be installed according
to the instructions suppliers below and by qualified and competent personnel to the relevant
National Standards.
Ref. Q.ty Installation components
7.2.1 2
Fixing brackets for upper chimney
11a
2
Plugs SB 12/10
12c 10 Screws 2,9 x 6,5
12e
2
Screws 2,9 x 9,5
The cooker hood is designed to be fixed to a solid block or
block wall over a cooking area. If not, suitable fixing must
be used for other types of walls. The hood can be used
in the extraction (ducted to the outside) or recirculation
(internal recycling) mode.
Q.ty Documentation
1
Instruction booklet
The Installation work must be undertaken by a qualified
and competent person. The manufacturer disclaims any
responsibility to damages due to incorrect installation of
the cooker hood or if the cooker hood is not installed in
compliance with relevant regulations controlling this type
of installation.
7.2.1
2.1
12c
2.2
9
8
10
12d
12c
16
11a
1
13
INSTALLING THE COOKER HOOD
Clearance Heights
The cooker hood is designed to be fitted over a cooking
appliance at the clearance heights stated, provided the
maximum output of the appliance beneath does not exceed the maximums quoted in the Technical
Specifications.
If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the
cooker manufacturer’s installation instructions.
Hob
A clearance height of 650mm (25 1/2 ins) is required when
installed above a built-in electric hob, or 700mm (27 1/2
ins) when installed above a built-in gas hob.
A: Built-in Electric Hob:
B: Built-in Gas hob:
C: Slot-in Electric Cooker:
D: Slot-in Gas Cooker:
A clearance height of 685mm (27 ins) is required when
installed above a slot-in electric oven, or 787mm (30 1/2
ins) when installed above a slot-in gas oven.
When installed between adjoining wall cabinets, the wall
cabinets must not overhang the hob and the distance
beetween the underside of the cabinet and the worktop
must be 450mm. If the height of the wall cabinet is less
than 450mm a gap of 50mm must be maintained
either side of the hob.
This cooker hood must not be installed above a
cooking appliance with a high level grill.
14
650mm clearance
700mm clearance
685mm clearance
787mm clearance
INSTALLATION INSTRUCTIONS
Wall drilling and bracket fixing
As a first step, proceed with the following drawings:
• a vertical line up to the ceiling or up to the upper
limit, at the centre of the area in which the hood is
to be fitted;
• a horizontal line at a minimum 960 mm above the
cooker top.
• Mark a point (1) on the horizontal line, 292 mm to
the right of the vertical reference line.
• Repeat this operation on the other side, checking
that the two marks are levelled.
• Mark a reference point (2) as indicated at 200 mm
from the vertical reference line and 458 mm above
the cooker top.
• Repeat this operation on the other side, checking
that the two marks are levelled.
• Mark a reference point (3) at 743 mm above the
cooker top on the vertical reference line.
• Drill at the marked points (1), using a ø 12 mm drill
bit.
• Drill at the marked points (2) and (3), using a ø 8
mm drill bit.
• Insert the bracket plugs 11a into the holes (1) and
tighten the screws.
• Place bracket 7.2.1 on the wall, about 1-2 mm from
the ceiling or from the upper limit, aligning the centre
(notch) with the vertical reference line.
• Mark the wall at the centres of the bracket holes.
• Place the bracket 7.2.1 on the wall at X mm below
the first bracket (X = height of the upper chimney
section), aligning the centre (notch) with the vertical
line.
• Mark the wall at the centres of the bracket holes.
• Drill ø 8 mm holes at all the marked centre points.
• Fix the brackets.
1÷2
1
11a
15
1
200 200
2
960
2
368
743
458
11
292 292
3
11
12a
12a
X
7.2.1
INSTALLATION INSTRUCTIONS
Hood body mounting
• Firstly, it is necessary to adjust the two Vr-screws of
the 11a-brackets, at minimun (B).
• Hang the hood body on the two brackets 11a.
• Connect the hood to the mains supply by means of
a bipolar switch with at least 3 mm contact gap.
• Press the “A”-key for one second (see Part USE) to
open the upper panel.
• Remove the metal filters.
• In order to align the hood it is necessary to adjust
the Vr-screws from inside the hood.
• Fasten the safety screw 11.
• Fit again the metal filters into their seats and close
the upper panel by pressing “L”-key for one second
(see Part USE).
• Disconnect the hood from the mains supply.
A
L
11a
Vr
(B)
Attention: the upper panel stops if any barrier occurs
in its way during the panel opening or closing. To
open the panel it is enough to remove the barrier
and press the key once again.
11
7.2.1
Chimney assembly
12c
Upper exhaust Chimney
• Slightly widen the two sides of the upper chimney
and hook them behind the brackets 7.2.1, making
sure that they are well seated.
• Secure the sides to the brackets using the 4 screws
12c (2,9 x 9,5) supplied.
2.1
2
2.2
Lower exhaust Chimney
• Slightly widen the two sides of the chimney and
hook them between the upper chimney and the wall,
making sure that they are well seated.
• Fix the lower part laterally to the hood body using
the 2 screws 12c (2,9 x 9,5) supplied.
12c
16
INSTALLATION INSTRUCTIONS
Electrical connection and working
test:
• Connect the hood to the mains supply.
• Open the upper panel by pressing the A-key (See
Part “USE” ) for at least 2 seconds.
• Remove the metal filters (See Part “MAINTENANCE”)
and make sure that the connector piece of the supply
cable is correctly inside the hood socket.
The symbol
on the product or on its packaging indicates that this product may not be treated as household waste. Instead
it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling
of this product, please contact your local city office, your household waste disposal service or the shop where you purchased
the product.
436004104_01 - 080220
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising