Panasonic | DMRE65 | Operating instructions | Panasonic DMRE65 Operating Instructions

Panasonic DMRE65 Operating Instructions
7303en.book 1 ページ
2004年5月31日 月曜日 午前9時32分
Operating Instructions
DVD Video Recorder
Model No.
Dear customer
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully.
Before connecting, operating or adjusting this product, please read
these instructions completely.
Please keep this manual for future reference.
DMR-E65
The warranty can be found on page 55.
La referencia rápida en español se puede encontrar
en la página 56.
Region number supported by this unit
Region numbers are allocated to DVD players and software
according to where they are sold.
This manual was printed with soy based ink.
≥The region number of this unit is “1”.
≥The unit will play DVDs marked with labels containing “1” or
“ALL”.
Example:
1
P
ALL
1
2
4
RQT7303-P
7303en.book 2 ページ
2004年5月31日 月曜日 午前9時32分
CAUTION!
Getting started
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PRODUCT DAMAGE, DO NOT
EXPOSE THIS APPARATUS TO RAIN, MOISTURE,
DRIPPING OR SPLASHING AND THAT NO
OBJECTS FILLED WITH LIQUIDS, SUCH AS
VASES, SHALL BE PLACED ON THE APPARATUS.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as
close to the point of cable entry as practical.
- VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
(FDA 21 CFR)
AVOID DIRECT EXPOSURE TO BEAM.
CAUTION - VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
(IEC60825-1)
ATTENTION - RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D’OUVERTURE.
EXPOSITION DANGEREUSE AU FAISCEAU.
ADVARSEL - SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.
UNDGÅ UDSÆTTELSE FOR STRÅLING.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
DANGER
VARO!
FCC Note:
- AVATTAESSA OLET ALTTIINA NÄKYVÄÄ JA NÄKYMÄTÖN
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
ADVARSEL - SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES.
UNNGÅ EKSPONERING FOR STRÅLEN.
VORSICHT - SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG
GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
-
RQLS0233
(Inside of product)
CAUTION!
DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE,
BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT
RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.
Keep the small memory cards such as the SD
Memory Card out of reach of children. If
swallowed, seek medical advice immediately.
The socket outlet shall be installed near the equipment and
easily accessible or the mains plug or an appliance coupler shall
remain readily operable.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
≥Reorient or relocate the receiving antenna.
≥Increase the separation between the equipment and receiver.
≥Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
≥Consult the dealer or an experienced radio/TV technician for
help.
FCC Caution: To assure continued compliance, follow the
attached installation instructions and use only shielded interface
cables when connecting to peripheral devices.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions
listed below. Keep these operating instructions handy for future reference.
1)
2)
3)
4)
5)
6)
7)
8)
9)
RQT7303
2
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
7303en.book 3 ページ
2004年5月31日 月曜日 午前9時32分
Table of contents
Transfer (Dubbing)
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . .2
Useful features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
The remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Control reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . .5
STEP 1 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
STEP 2 Setting up the TV Guide On ScreenTM
system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
STEP 3 Set up to match your television and remote
control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Disc and card information . . . . . . . . . . . . . . . . . . . . . . . .14
Recording
Recording television programs . . . . . . . . . . . . . . . . . . . .16
Recording modes and approximate recording times . . . . . . . .
Selecting audio to record . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playing while you are recording. . . . . . . . . . . . . . . . . . . . . . . .
Flexible Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
18
18
Timer recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Using the TV Guide On ScreenTM system to make timer
recordings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manually programming timer recordings . . . . . . . . . . . . . . . . .
Using VCR Plusi system to make timer recordings . . . . . . . .
Check, change or delete a program. . . . . . . . . . . . . . . . . . . . .
19
20
21
22
Utilizing TV Guide On ScreenTM system . . . . . . . . . . . . .23
Playing back
Playing recorded video contents/
Playing play-only discs . . . . . . . . . . . . . . . . . . . . . . . . .24
Operations during play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Editing operations during play . . . . . . . . . . . . . . . . . . . . . . . . . 26
Changing audio during play . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Using menus to play MP3 . . . . . . . . . . . . . . . . . . . . . . . .27
Playing still pictures. . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Transferring (dubbing) still pictures . . . . . . . . . . . . . . . 38
Transferring (dubbing) using the transferring (dubbing) list . . . 38
Transferring (dubbing) all the still pictures of a card onto a
DVD-RAM—COPY ALL PICTURES . . . . . . . . . . . . . . . . . . . 39
Recording from a video cassette recorder . . . . . . . . . . 39
Convenient functions
FUNCTIONS window . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Disc and card setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Setting the protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Providing a disc with a name . . . . . . . . . . . . . . . . . . . . . . . . . .
Erasing all titles and play lists—Erase all titles . . . . . . . . . . . . .
Erasing all the contents of a disc or card—Format. . . . . . . . . .
Enabling DVD-R to be played on other equipment—Finalize . .
40
40
41
41
41
Getting started
Getting started
Changing the unit’s settings . . . . . . . . . . . . . . . . . . . . . 42
Common procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Summary of settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Channel/Clock settings when TV Guide On ScreenTM
system is not used . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Auto channel/clock settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Channel captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Reference
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . 49
Error messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Product Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Maintenance/Disc and card handling . . . . . . . . . . . . . . 54
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Guía de referencia rápida en español . . . . . . . . . . . . . 56
(Spanish Quick Reference)
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Backcover
Useful functions during still picture play. . . . . . . . . . . . . . . . . . 29
Using on-screen menus and Status messages . . . . . . .30
On-screen menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Status messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Editing
Editing titles/chapters . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Editing titles/chapters and playing chapters. . . . . . . . . . . . . . . 32
Title operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Creating, editing and playing play lists . . . . . . . . . . . . .34
Creating play lists. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing and playing play lists/chapters . . . . . . . . . . . . . . . . . . .
Play list operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
35
35
35
Editing still pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Picture and folder operation. . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Entering text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Useful features
This DVD Video recorder records high quality images to rapid
random access capable DVD-RAM. This has resulted in many new
features that out perform older tape formats. The following
information summarizes a few of these features.
Instant recording
You no longer need to search for empty disc space. By pressing the
recording button, the unit finds available recording space and begins
recording right away. There is no need to worry about overwriting
already recorded content.
SD/PC card slots
This unit is equipped with interfaces that allow networking with digital
equipment.
≥The SD/PC card slots of this unit let you transfer (dub) digital
camera photographs from a card to DVD-RAM for easy storage
without using a computer.
Instant play
There is no need to rewind or search forward. Direct Navigator
guides you to the beginning of the recorded video immediately.
Chasing playback
There is no need to wait until recording is
complete. Without stopping recording, you can
play the video currently being recorded from its
beginning.
Simultaneous Recording and Playback
While recording, you can play another video
program that was recorded previously.
TV Guide On ScreenTM system
The TV Guide On ScreenTM system provides a handy electronic
program guide (EPG) for checking what’s on. Setting up to record a
broadcast is easy too. Simply select the desired program from the
displayed list. You can also search for desired programs alphabetically
or by displaying only the programs in a certain category.
≥This service may not be available in some areas.
Time Slip
During play and also while recording, you can
jump to the scene you wish to view by specifying
the skip time.
RQT7303
3
7303en.book 4 ページ
2004年5月31日 月曜日 午前9時32分
Accessories
Getting started
Please check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts.
To order accessories, refer to “Accessory Purchases” on page 55.
∏
∏
∏
1 Remote control
(EUR7721KB0)
1 AC power supply cord
(K2CB2CB00006)
1 75 ≠ coaxial cable
(VJA1125)
≥For use with this unit only. Do not use it with
other equipment.
∏
∏
∏
2 Batteries
for remote control
1 Audio/video cable
(K2KA6CA00001)
1 IR Blaster
(K2ZZ04C00002)
Product Registration Card
Please complete and return the included product registration card, or register via the Internet at: http://www.prodreg.com/panasonic/
The remote control
∫ Batteries
∫ Use
R6/LR6, AA, UM-3
Remote control signal sensor
20˚
30˚
20˚
30˚
≥Insert so the poles (i and j) match those in the remote control.
≥Do not use rechargeable type batteries.
≥Do not mix old and new batteries.
≥Do not use different types at the same time.
≥Do not heat or expose to flame.
≥Do not take apart or short circuit.
≥Do not attempt to recharge alkaline or manganese batteries.
≥Do not use batteries if the covering has been peeled off.
7 m (23 feet) directly in front of the unit
Mishandling of batteries can cause electrolyte leakage which can
damage items the fluid contacts and may cause a fire.
Remove if the remote control is not going to be used for a long
period of time. Store in a cool, dark place.
[Note]
If you cannot operate the unit or television using the remote control
after changing the batteries, please re-enter the codes
(➡ page 12, 13).
The manufacturer accepts no responsibility and offers no compensation for loss of recorded or edited material due to a problem
with the unit or recordable media, and accepts no responsibility and offers no compensation for any subsequent damage caused by
such loss.
Examples of causes of such losses are
≥A disc recorded and edited with this unit is played in a DVD recorder or computer disc drive manufactured by another company.
≥A disc used as described above and then played again in this unit.
≥A disc recorded and edited with a DVD recorder or computer disc drive manufactured by another company is played in this unit.
RQT7303
4
7303en.book 5 ページ
2004年5月31日 月曜日 午前9時32分
Control reference guide
DVD POWER
Turn the unit on (➡ page 10)
TV
POWER
INPUT SELECT TV/VIDEO
VOLUME
CH
Television operations (➡ page 12)
Input select (L1, L2 or L3) (➡ page 39)
DVD
DRIVE SELECT
SD/PC
Select drive (DVD, SD or PC) (➡ page 16, 24, 29)
PAGE
Select channels and title numbers, etc./
Enter numbers
1
2
3
4
5
6
7
8
CH
Channel select (➡ page 16)
Getting started
Remote control
AUDIO
Cancel
Select audio (➡ page 17, 26)
9
VCR Plus+ CM SKIP
CANCEL
0
SKIP
STOP
Basic operations for recording and play
SLOW/SEARCH
PAUSE
Show VCR Plusr screen (➡ page 21)
PLAY/x1.3
DIRECT NAVIGATOR
Show Top menu/Direct Navigator
(➡ page 24, 32)
Skip a minute forward (➡ page 25)
FUNCTIONS
Show FUNCTIONS window (➡ page 40)
TOP MENU
Selection/Enter, Frame-by-frame (➡ page 10, 25)
ENTER
SUB MENU
Show sub menu (➡ page 32)
RETURN
Return to previous screen
Skip the specified time/Display the television image
as a picture-in-picture (➡ page 18, 25)
Show on-screen menu (➡ page 30)
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
Show timer recording schedule (➡ page 20)
Erase items (➡ page 26)
SETUP
Show SETUP menu (➡ page 11, 42)
ERASE REC MODE
REC
Show television program list (➡ page 19)
Change recording mode (➡ page 16)
Start recording (➡ page 16)
Changing the size of information window
(➡ page 23)
Info
CHAPTER STATUS
Show status messages (➡ page 31)
Create chapters/“Green” button for television program
list (➡ page 26, 19)
“Blue” button for television program list
(➡ page 19)
Main unit
Remote control signal sensor/Start recording (➡ page 16)
POWER button (POWER Í/I) (➡ page 10)
Press to switch the unit from on to standby mode or
Stop (➡ page 16, 25)
vice versa. In standby mode, the unit is still
Select drive (➡ page 16, 24, 29)
consuming a small amount of power.
Lights when the DVD, SD or PC drive is
Disc tray (➡ page 16, 24)
selected
SD/PC card slots (➡ page 28)
Open/close disc tray (➡ page 16, 24)
Start play
(➡ page 24)
OPEN/CLOSE
SD CARD
PC CARD
REC
EJECT
POWER
TIME SLIP
DVD
SD
PC
DRIVE SELECT
TIME SLIP
L2
S-VIDEO IN
VIDEO IN
L/MONO AUDIO IN
/x1.3
CH
R
Display (➡ below)
Time Slip indicator
(➡ page 18)
Skip the specified time/Display the television image
as a picture-in-picture (➡ page 18, 25)
Connection for camcorder,
etc. (➡ page 39)
Skip/Slow/Search
(➡ page 25)
Channel select (➡ page 16)
Rear panel terminals (➡ page 7)
The unit’s display
Card indicator Recording mode
Timer recording indicator
Transfering (dubbing) in progress indicator
DVD - R AM
SD PC XP
Channel
Recording
REC
Disc type
VCD.MIX
SP
LP
EP CH
PLAY REC
Main display section
Playback
PLAY
Recording/Playback
PLAY REC
D.MIX (multi-channel DVD-Audio only)
When lit: Down-mixed audio is played.
When off: The disc prevents down-mixing so only the two
front channels can be played.
RQT7303
5
7303en.book 6 ページ
2004年5月31日 月曜日 午前9時32分
STEP 1 Connection
∫ Examples of equipment you can connect to this unit’s terminals
Amplifier
Getting started
Television
From OUT1 or OUT2
terminals
From AUDIO OUT terminals or
DIGITAL AUDIO OUT terminal
This unit
To L2 input terminals (front)
(➡ page 39)
To IN3 (L3) input
terminals (rear)
To IN1 (L1) input
terminals (rear)
Video cassette recorder
Camcorder
Cable TV box
Do not place the unit on
amplifiers or equipment
that may become hot.
The heat can damage the unit.
Before moving the unit, ensure the disc tray is empty.
Failure to do so will risk severely damaging the disc and the
unit.
RQT7303
6
∫ When the unit is not to be used for a long time
To save power, unplug it from the household AC outlet. This unit
consumes a small amount of power, even when it is turned off
(approx. 15 W).
≥Note that the television program list is not downloaded while the
unit is unplugged.
7303en.book 7 ページ
2004年5月31日 月曜日 午前9時32分
≥The equipment connections described are examples.
≥Before connection, turn off all equipment and read the appropriate operating instructions.
≥Peripheral equipment and optional cables sold separately unless otherwise indicated.
A to X are indexes for Spanish Quick Reference.
A
1–4
indicates included accessories.
indicates accessories not included.
are required connections. Connect in the numbered order.
Connecting a cable TV box
➡ page 8
B Television
D Cable TV
C When making this
connection, ensure you
connect the audio cables to
the corresponding audio
input terminals on the
television.
G AC power supply cord
Connect only after all other
connections are complete.
AUDIO IN
R L VIDEO IN S VIDEO IN
E Outdoor
antenna
VHF/UHF
RF IN
COMPONENT
VIDEO IN
F Indoor
antenna
H Red White Yellow
4
I To household AC outlet
(AC 120 V, 60 Hz)
M Audio/Video
cable
J 75 ≠ coaxial cable
➡ below
N S-Video O Component
cable
video cable
3
Getting started
Connecting a television and VCR
L To the
K Antenna
antenna
cable
P Splitter
2
1
Q To OUT1 or OUT2
RF IN
H Red White Yellow
R - AUDIO - L
VIDEO S-VIDEO
VIDEO S-VIDEO
PB
R - AUDIO - L
VIDEO S-VIDEO
R - AUDIO - L
VIDEO
(L1)
PR
OPTICAL
COMPONENT
VIDEO OUT
(480P/480I)
IN3
OUT2
R - AUDIO - L
Y
IN1
OUT1
G-LINK
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
RF OUT
S-VIDEO (L3)
VHF/UHF
H Red White Yellow
R Cooling fan
S To IN1 (L1)
U S-VIDEO OUT terminal
The S-VIDEO OUT terminal achieves a more vivid picture
than the VIDEO OUT terminal. (Actual results depend on the
television.)
M Audio/Video
cable
W COMPONENT VIDEO OUT terminal
These terminals can be used for either interlace or progressive output
(➡ page 48) and provide a purer picture than the S-VIDEO OUT
terminal.
≥Connect to terminals of the same color.
∫ 75 ≠ coaxial cable
The picture and sound signal from this unit does not go through the
75 ≠ coaxial cable to the television. Make sure you connect one of
the following terminals on this unit to the television: the AUDIO/
VIDEO OUT terminal, the S-VIDEO OUT terminal or the
COMPONENT VIDEO OUT terminal. If the television has none of
these terminals, consult your local dealer.
≥Refer to page 9 if the antenna connector doesn’t match.
T This unit
J 75 ≠ coaxial
cable
V Use a splitter if you also
want to connect the
antenna to your VCR.
H Red White Yellow
R
L
VIDEO
AUDIO OUT OUT
X Video cassette recorder
VHF/UHF
RF IN
Do not connect the unit through a video cassette recorder
Video signals fed through video cassette recorders will be affected
by copyright protection systems and the picture will not be shown
correctly on the television.
B Television
B Television
T This unit
X VCR
X VCR
T This unit
≥When connecting to a television with a built in VCR, connect to
the input terminals on the television side, not the VCR side.
RQT7303
7
7303en.book 8 ページ
2004年5月31日 月曜日 午前9時32分
STEP 1 Connection
Connecting a cable TV box
Getting started
≥You need to subscribe to a cable TV service to enjoy viewing their programming.
≥Consult your service provider regarding appropriate cable TV box.
≥If you receive your programming solely from a satellite service, the program guide in this unit will not receive program listings or
channel information. Without this information, program-based recordings cannot be made. However, recordings can still be set
manually.
A to Q are indexes for Spanish Quick Reference.
A Television
AUDIO IN
R L VIDEO IN S VIDEO IN
VHF/UHF
RF IN
D 75 ≠ coaxial
cable§
C Audio/video cable§
B This unit
RF IN
R - AUDIO - L
VIDEO S-VIDEO
Y
PB
R - AUDIO - L
VIDEO S-VIDEO
R - AUDIO - L
VIDEO
(L1)
IN1
OUT1
G-LINK
PR
OPTICAL
VIDEO S-VIDEO
COMPONENT
VIDEO OUT
(480P/480I)
IN3
OUT2
R - AUDIO - L
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
G Red White Yellow
E IR Blaster
Insert the IR Blaster jack into
the G-LINK terminal.
The cable TV box is
controlled by an IR signal
transmitted through the IR
Blaster.
When selecting channels on
this unit, the corresponding
channels on the cable TV
box also change accordingly.
≥Only use the included IR
Blaster.
RF OUT
S-VIDEO (L3)
F Use IN3 (L3) [not IN1 (L1)].
VHF/UHF
H Connect to either this
unit’s RF IN terminal or
IN3 (L3) terminal.
D 75 ≠ coaxial cable
I S-Video cable
C Audio/video cable
G Red White Yellow
J Setting the IR Blaster
➡ below
R
L
AUDIO
VIDEO
S-VIDEO
OUT
IN
RF
K Cable TV box
L From antenna or
cable TV jack
§ For more information on connections (➡ page 7)
∫ Should I use the AUDIO/VIDEO OUT terminal or
the RF OUT terminal?
If your cable TV box has both AUDIO/VIDEO OUT terminals and
RF OUT terminals, we recommend connecting the AUDIO/VIDEO
OUT terminal with the unit’s IN3 (L3) terminal. Using this
connection provides better picture quality.
≥The S-VIDEO terminal achieves a more vivid picture than the
VIDEO terminal.
Setting the IR Blaster
Place the IR Blaster in front of the signal sensor of the cable TV
box.
N If necessary, use the double sided adhesive tape (included) to
secure the IR Blaster to a flat surface.
M Read the cable TV box operating instructions regarding
positioning of the signal sensor.
O e.g. Television stand surface
Q If you peel off the adhesive tape, the
surface may become damaged.
Once you have confirmed the cable TV
box is operating correctly, secure it by
attaching the adhesive tape.
P Cable TV box
RQT7303
8
7303en.book 9 ページ
2004年5月31日 月曜日 午前9時32分
Connecting an amplifier or system component
∫ To enjoy multi-channel surround sound on
DVD-Video
Amplifier’s rear panel
Connect an amplifier with a built-in decoder
displaying these logo marks using an optical digital
audio cable and change the settings in “Digital Audio
Output” (➡ page 44).
AUDIO IN
R L
≥You cannot use DTS Digital Surround decoders not suited to
DVD.
≥Even if using this connection, output will be only 2 channels when
playing DVD-Audio.
Red White
Getting started
∫ Connection to a stereo amplifier
Amplifier’s rear panel
OPTICAL IN
Audio cable
Insert fully, with this
side facing up.
Optical digital audio
cable
Do not bend sharply
when connecting.
To OUT1 or OUT2
This unit
RF IN
Red White
R - AUDIO - L
VIDEO S-VIDEO
Y
PB
R - AUDIO - L
VIDEO S-VIDEO
R - AUDIO - L
VIDEO
(L1)
IN1
OUT1
G-LINK
PR
OPTICAL
VIDEO S-VIDEO
COMPONENT
VIDEO OUT
(480P/480I)
IN3
OUT2
R - AUDIO - L
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
S-VIDEO (L3)
RF OUT
VHF/UHF
If the antenna connector doesn’t match
Other antenna connections to the unit
Other antenna connections from the unit to the
television
Use one of the following connections to suit the antenna lead.
≥If your television has both lead and coaxial VHF terminals, use
the lead connection to minimize signal loss.
Use one of the following connections to suit the antenna terminals
on your television. Refer to the television’s operating instructions.
∫ A single twin lead
∫ A twin lead and coaxial plug terminal
from the antenna
(Flat) Twin lead
300 ≠ cable
300–75 ≠ transformer
VHF/UHF band separator
To this unit’s RF IN
terminal
from the antenna
75–300 ≠ transformer
VHF/UHF band mixer
(Flat) Twin lead 300 ≠ cable
To this unit’s RF IN
terminal
75 ≠ coaxial cable
VHF or
UHF
Television
∫ Two twin lead terminals
VHF/UHF band separator
VHF
UHF
75 ≠ coaxial cable
∫ Two twin leads
from the antenna
Television
∫ Multiple antenna terminals
VHF/UHF band mixer
(Flat) Twin lead
300 ≠ cable
300–75 ≠ transformer
UHF
Television
75 ≠ coaxial cable
∫ A twin lead terminal
∫ A twin lead and a coaxial cable
(Round)
75 ≠ coaxial cable
VHF
To this unit’s RF
IN terminal
≥Connect to one of the ANT terminals, then change the television’s
settings as necessary.
Television
Split out
ANT 1
75 ≠ coaxial cable
ANT 2
RQT7303
9
7303en.book 10 ページ
2004年5月31日 月曜日 午前9時32分
STEP 2 Setting up the TV Guide On ScreenTM system
POWER Í/I
OPEN/CLOSE
SD CARD
PC CARD
REC
EJECT
Getting started
POWER
TIME SLIP
DVD
SD
PC
DRIVE SELECT
TIME SLIP
DVD POWER
Í DVD POWER
/x1.3
CH
1
TV
POWER
INPUT SELECT TV/VIDEO
DVD
Preparation
≥Turn on the television and select the appropriate video input to
suit the connections to this unit.
≥When using the cable TV box, check the following.
–Make sure the IR Blaster is connected and positioned properly
(➡ page 8).
–Make sure the cable TV box is turned on.
VOLUME
CH
DRIVE SELECT
Press [Í DVD POWER].
Welcome to Your TV Guide On Screen System!
SD/PC
PAGE
Numbered
buttons
1
2
3
4
5
6
7
8
CH
AUDIO
9
VCR Plus+ CM SKIP
CANCEL
0
SKIP
STOP
SLOW/SEARCH
PAUSE
2
PLAY/x1.3
DIRECT NAVIGATOR
FUNCTIONS
TOP MENU
3,4,2,1
ENTER
ENTER
SUB MENU
RETURN
Following the on-screen messages,
input the operating environment for
your television.
≥Move the cursor using [3, 4, 2, 1] and press [ENTER]
to confirm.
≥Press the numbered buttons to enter numbers.
≥Press [ENTER] to advance to the next screen.
≥Refer to the guidance on the bottom of the screen.
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
SETUP
SETUP
Info
ERASE REC MODE
REC
CHAPTER STATUS
Set the following;
≥Country (USA/Canada)
Which country is your DVD Recorder located in?
USA
Canada
≥ZIP (Postal) code
After plugging the unit into your household AC outlet and pressing
[Í DVD POWER] to turn the unit on for the first time, the unit starts
TV Guide On ScreenTM system setup.
Please enter the 5-digit ZIP code where your DVD Recorder
is located:
=
Even if you do not want to use the TV Guide On
ScreenTM system, complete the setup. You cannot use
timer recording unless the setup is completed.
=
=
=
=
≥Cable service connected to this unit (Yes/No)
Do you have cable service connected to this DVD Recorder?
Only English is displayed in the TV Guide On
ScreenTM system. Other languages cannot be
displayed.
Yes
No
When “No” is selected ➡ right, “The set contents are displayed
together”
TV Guide On ScreenTM system
This unit downloads a free television program list from a TV
station and displays the list on the television screen. The list
offers you many convenient functions such as timer recording
(➡ page 19) and so on (➡ page 23).
≥If you receive your programming solely from a satellite
service, the program guide in this unit will not receive program
listings or channel information. Without this information,
program-based recordings cannot be made. However,
recordings can still be set manually.
Downloading the television program list
RQT7303
10
≥The unit downloads the television program list only when the
unit is turned off.
≥When the unit is connected to a cable TV box, the cable TV
box must be turned on in order to download the television
program list.
≥In order to cool the circuits used for downloading the television
program list, sometimes the cooling fan operates when the
unit is turned off. This is not a malfunction.
≥Cable TV box connected to this unit (Yes/No)
Is a cable box connected to this DVD Recorder?
Yes
No
When “No” is selected ➡ right, “The set contents are displayed
together”
If you do not want to use the TV Guide On ScreenTM system
Select “No” at this point even if a cable TV box is connected.
2004年5月31日 月曜日 午前9時32分
If you are using a cable TV box, set the following:
≥Cable TV box connection channel (Ch2/Ch3/Ch4/L3)
–If you are connecting the cable TV box to this unit’s IN3 (L3)
terminal, select “L3”.
–If you are connecting the cable TV box to this unit’s RF terminal,
select “Ch2”, “Ch3” or “Ch4”, according to the cable TV box
setting.
≥Cable TV box brand
(Move down with [4] for more brands. Select “Not Listed” if you
cannot find your cable TV box on the list.)
≥IR signal code
Make sure your cable TV box is set to the channel that appears
on screen and press [ENTER]. A test is performed.
To use immediately (Manual Clock Setting)
Set the clock manually.
Please note that the program list is not displayed until the unit
downloads it. Timer program recording is only possible manually.
1
2
Press [SETUP].
3
Press [3, 4] to select “Manual Clock
Setting” and press [ENTER].
Is your cable box now tuned to channel 09?
Press [3, 4] to select “Set Up” and
press [1].
MONTH
No
–If the cable TV box has changed to channel 09, select “Yes” and
press [ENTER].
–If the cable TV box is still set to the same channel, select “No”
and press [ENTER]. Repeat this step until the cable TV box
changes to channel 09.
Channel
Set Up
Disc
Video
4
∫ The set contents are displayed together
5
Zip code - 11111 (USA)
Cable
- Yes
Cable box - No
Once you confirm the input content, the following screen appears.
What would you like to do now?
Watch TV
Press [ENTER].
A television reception screen or a blue background screen is
displayed.
If you do not want to use TV Guide On ScreenTM system
➡ page 45, Auto channel/clock settings
4
Press [Í DVD POWER].
Leave the unit turned off until the unit downloads the television
program list. This may take up to a maximum of 24 hours.
When the unit is connected to a cable TV box
≥The cable TV box must be turned on in order to download the
television program list.
≥Note that the television program list may not be downloaded
correctly if you change the channel of the cable TV box while the
unit is turned off.
If you find “There is no data for this screen” on the television when
you turn the unit on, the unit has not yet downloaded the program
list.
SCHEDULE
LISTINGS
SORT
SCHEDULE
TODAY
LISTINGS
8:00PM
SORT
8:30PM
Last
Channel
87
NWGB
FAVORITES
RECORD
INFO.
pTV
There is no data
for this screen.
1
DAY
/
1
YEAR
/
2000 SAT
HOUR
MINUTE
12 : 00 AM
DST
TIME ZONE
OFF
EST
Press [2, 1] to select the item you
want to change and press [3, 4] to
change the setting.
Press [ENTER].
The clock starts.
–If the information is correct, select “Yes, end setup” and press
[ENTER].
–If the information is not correct, select “No, repeat setup
process” and press [ENTER] to start the setting again.
3
Manual Clock Setting
SETUP
Yes
Getting started
7303en.book 11 ページ
TV
NWBG
ducation
6
Press [SETUP].
≥DST (Daylight Saving Time): ON or OFF
If you select “ON”, the clock is advanced one hour starting at 2
a.m. on the first Sunday in April and ending at 2 a.m. on the last
Sunday in October.
≥TIME ZONE shows the time difference from Greenwich
meantime (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time) l GMT j6
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time)
l GMT j8
AST (Alaska Standard Time)
l GMT j9
HST (Hawaii Standard Time)
l GMT j10
In the United States, TV GUIDE and other related marks are
registered marks of Gemstar-TV Guide International, Inc. and/
or one of its affiliates. In Canada, TV GUIDE is a registered
mark of Transcontinental Inc., and is used under license by
Gemstar-TV Guide International, Inc. TV Guide On Screen,
G-LINK, VCR Plusr and PlusCode are registered marks of
Gemstar-TV Guide International and/or one of its affiliates.
The TV Guide On Screen and VCR Plusr systems are
manufactured under license from Gemstar-TV Guide
International, Inc. and/or one of its affiliates.
GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/
OR ITS RELATED AFFILIATES ARE NOT IN ANY WAY
LIABLE FOR THE ACCURACY OF THE PROGRAM
SCHEDULE INFORMATION PROVIDED BY THE TV
GUIDE ON SCREEN SYSTEM. IN NO EVENT SHALL
GEMSTAR- TV GUIDE INTERNATIONAL, INC. AND/
OR ITS RELATED AFFILIATES BE LIABLE FOR ANY
AMOUNTS REPRESENTING LOSS OF PROFITS,
LOSS OF BUSINESS, OR INDIRECT, SPECIAL, OR
CONSEQUENTIAL DAMAGES IN CONNECTION
WITH THE PROVISION OR USE OF ANY
INFORMATION, EQUIPMENT, OR SERVICES
RELATING TO THE TV GUIDE ON SCREEN SYSTEM.
BOX
ANiMe
Network
PBS
This unit may download more than one channel line-up. Follow the
on-screen guidance and select one of the channel line-ups
(➡ page 23).
The TV Guide On Screen and VCR Plusr systems are
protected by one or more issued United States patents such as
6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713;
4,751,578; 4,706,121; 6,466,734; 6,430,359; 6,091,882;
6,049,652; 5,335,079; 5,307,173.
RQT7303
11
7303en.book 12 ページ
2004年5月31日 月曜日 午前9時32分
STEP 3 Set up to match your television and remote control
DVD POWER
Television operation
TV
POWER
Getting started
DVD
VOLUME
CH
INPUT SELECT TV/VIDEO
TV operation
buttons
SD/PC
DRIVE SELECT
PAGE
1
Numbered
buttons
2
While pressing [Í POWER TV], enter the
code with the numbered buttons.
3
CH
4
5
7
8
6
e.g., 01: [0] ➡ [1]
Manufacturer and Code No.
AUDIO
9
VCR Plus+ CM SKIP
CANCEL
0
SKIP
STOP
SLOW/SEARCH
PAUSE
PLAY/x1.3
DIRECT NAVIGATOR
3,4,2,1
ENTER
ENTER
SUB MENU
RETURN
RETURN
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
SETUP
Info
ERASE REC MODE
REC
You do not have to change the setting when connected to a 4:3
standard aspect television that is not compatible with progressive
output (➡ page 48).
1
2
Press [SETUP].
3
Press [3, 4] to select “TV Type” and
press [ENTER].
Press [3, 4] to select “TV Screen”
and press [1].
TV Type
Aspect 4:3 & 480I
Aspect 4:3 & 480P
Channel
Set Up
Disc
Video
Audio
Display
TV Screen
Aspect 16:9 & 480I
Aspect 16:9 & 480P
≥Aspect 4:3/Aspect 16:9:
4:3
16:9
4:3 standard aspect
16:9 widescreen
television
television
≥480P/480I:
Select “480P” if the television is compatible with
progressive output.
4
Press [3, 4] to select the item and
press [ENTER].
To exit the screen
Press [SETUP].
RQT7303
12
01, 02
FISHER
GE
PHILIPS (RC-5)
03
RCA
05
SAMSUNG
14, 18, 19
10
SANYO
10
05
SHARP
06, 07
GOLDSTAR
15, 16, 17
SONY
08
HITACHI
12
SYLVANIA
03
To return to the previous screen
Press [RETURN].
JVC
11
THOMSON
05
LG
15, 16, 17
TOSHIBA
09
MAGNAVOX
03
ZENITH
04
MITSUBISHI
13
Test by turning on the television and changing channels. Repeat
the procedure until you find the code that allows correct operation.
≥If your television brand is not listed or if the code listed for your
television does not allow control of your television, this remote
control is not compatible with your television.
CHAPTER STATUS
Selecting television type
SETUP
Panasonic
National
QUASAR
FUNCTIONS
TOP MENU
SETUP
You can configure the remote control TV operation buttons to turn
the television on/off, change the television input mode, select the
television channel and change the television volume.
Point the remote control at the television
7303en.book 13 ページ
2004年5月31日 月曜日 午前9時32分
Change the remote control code on the main unit and the remote
control (the two must match) if you place other Panasonic products
close together.
Use “1”, the factory set code, under normal circumstances.
1
2
3
4
Press [SETUP].
Press [3, 4] to select “Set Up” and
press [1].
Press [3, 4] to select “Remote
Control Code” and press [ENTER].
Press [3, 4] to select the code (1, 2,
or 3) and press [ENTER].
SETUP
Channel
Set Up
Disc
Getting started
When other Panasonic products
respond to this remote control
Remote Control Code
Press “±” and “ENTER” together
for more than 2 seconds on the remote.
5
To change the code on the remote control
6
While pressing [ENTER], press and
hold the numbered button ([1], [2] or
[3]) for more than 2 seconds.
Press [ENTER].
∫ When the following indicator appears on the
unit’s display
The unit’s remote control code
Change the code on the remote control to match the main unit’s
(➡ step 5).
To exit the screen
Press [SETUP].
To return to the previous screen
Press [RETURN].
RQT7303
13
7303en.book 14 ページ
2004年5月31日 月曜日 午前9時32分
Disc and card information
Discs you can use for recording and play [12 cm (5z)/8 cm (3z)]
Getting started
Disc type
Logo
Instructions
Re-writable discs
≥You can record up to 16 hours [in EP (8H) mode on double-sided disc. You cannot record or
play continuously on two sides.] (➡ page 17, Recording modes and approximate recording
times).
≥You can view the title being recorded from the beginning (Chasing playback, Time Slip)
(➡ page 18).
≥Scratch and dust resistant cartridge discs and large capacity double sided discs (9.4GB) are
commercially available.
≥You can record digital broadcasts that allow “One time only recording” when using CPRM
(Content Protection for Recordable Media) compatible discs (➡ page 48).
≥This unit is compatible with 1k–3k recording speed discs.
≥You can play and transfer (dub) still pictures taken on a digital camera etc. (➡ page 28, 38).
DVD-RAM
≥4.7 GB/9.4 GB, 12 cm
(5z)
≥2.8 GB, 8 cm (3z)
Indicated in these
instructions with [RAM]
One time recording discs (recordable until the disc is full)
≥You can record up to 8 hours [in EP (8H) mode] (➡ page 17, Recording modes and
approximate recording times).
≥By finalizing the disc, you can play it in a DVD player as DVD-Video (Play only) (➡ page 41,
48).
≥You cannot record digital broadcasts that allow “One time only recording”.
≥This unit is compatible with 1k–4k recording speed discs.
DVD-R
≥4.7 GB, 12 cm (5z)
≥1.4 GB, 8 cm (3z)
[DVD-R]
≥We recommend using Panasonic discs and cards. DVD-R from other manufacturers may not be recorded or played due to the condition of the
recording.
∫ Which should I use, DVD-RAM or DVD-R?
The following chart indicates the differences. Select based upon what you require.
(±:Possible, t:Impossible)
DVD-R
Re-writable
±
t
Edit
±
§1
§3
±§2
±§3
§4
±
t§4
§5
Play on other players
Recording both Main and SAP of
MTS broadcast
Recording broadcasts that allow
one copy
Recording 16:9 aspect picture
±
§5
±
Disc type
DVD-Audio
[DVD-A]
DVD-Video
[DVD-V]
Logo
§6
§6
Instructions
High fidelity music discs
≥Played on this unit in 2 channels.
High quality movie and
music discs
Video CD
[VCD]
Recorded music and video (including
CD-R/RW)
Audio CD
[CD]
Recorded music and audio
(including CD-R/RW)
CD-R and CD-RW with music
recorded in MP3 (➡ page 27)
≥This unit plays CD-R/CD-RW discs (audio recording discs) which
have been recorded under one of the following standards: CD-DA,
MP3 and Video CD. Close the session or finalize the disc after
recording.
Play may be impossible on some CD-R or CD-RW discs due to the
condition of the recording.
≥The producer of the disc can control how discs are played. So you
may not always be able to control play as described in these
operating instructions. Read the disc’s instructions carefully.
14
§2
You can erase, enter name and change thumbnail. Available
space does not increase after erasing.
Only on DVD-RAM compatible players.
After finalizing the disc (➡ page 41, 48).
Only one is recorded (➡ page 43, Select MTS).
CPRM (➡ page 48) compatible discs only.
The picture is recorded in 4:3 aspect.
t
Play-only discs [12 cm (5z)/8 cm (3z)]
RQT7303
§1
DVD-RAM
Discs that cannot be played
≥2.6 and 5.2 GB DVD-RAM, 12 cm (5z)
≥3.95 and 4.7 GB DVD-R for Authoring
≥Unfinalized DVD-R recorded on other equipment (➡ page 48,
Finalize)
≥PAL discs (you can still play the audio on DVD-Audio)
≥DVD-Video with a region number other than “1” or “ALL”
≥DVD-ROM, DVD-RW, iR, iRW, CD-ROM, CDV, CD-G, Photo CD,
CVD, SVCD, SACD, MV-Disc, PD, Divx Video Disc, etc.
7303en.book 15 ページ
2004年5月31日 月曜日 午前9時32分
Cards useable on this unit
Instructions
SD Memory Card
MultiMediaCard
You can insert directly into
the SD card slot.
[SD]
SD Memory Card
MultiMediaCard
CompactFlash
SmartMedia
MEMORYSTICK
xD-Picture Card
Microdrive
≥You can play and transfer (dub) still pictures taken on a digital camera etc.
(➡ page 28, 38).
≥You can set the DPOF (Digital Print Order Format) for automatic printing on your
home printer or at a photo developing store (➡ page 36, 48).
You can insert into the PC
card slot using an adaptor
(TYPE II PC card adaptor).
[PC]
≥Compatible with: FAT 12 or FAT 16
≥We recommend using a Panasonic SD card.
≥You cannot use SD cards that exceed 2 GB.
≥We recommend using this unit to format a card before recording (➡ page 41, 48).
≥You may not be able to use the card if formatted on a computer.
ATA Flash PC Card
Mobile hard disk§
You can insert directly into
the PC card slot.
[PC]
§
Getting started
Type
Content saved on SD media storage (SV-PT1).
You can only play the recorded still pictures and transfer (dub) the data onto other
cards or DVD-RAM.
Structure of folders displayed by this unit
The following
¢¢¢: Numbers
can be displayed on this unit.
XXX: Letters
DVD-RAM
Card
JPEG
DCIM (Higher folder)
DCIM¢¢¢ (Higher folder)
¢¢¢XXXXX
¢¢¢XXXXX
XXXX¢¢¢¢.JPG
XXXX¢¢¢¢.TIF
IM¢¢CDPF or IMEXPORT
XXXX¢¢¢¢.JPG
XXXX¢¢¢¢.TIF
§
§
DCIM
XXXX¢¢¢¢.JPG
XXXX¢¢¢¢.TIF
¢¢¢XXXXX
XXXX¢¢¢¢.JPG
XXXX¢¢¢¢.TIF
§ Folders can be created on other equipment. However, these folders cannot be selected as a transferring (dubbing) destination.
≥The folder cannot be displayed if the numbers are all “0” (e.g., DCIM000 etc).
≥If a folder name or filename has been input using other equipment, the name may not be displayed properly or you may not be able to play or
edit the data.
RQT7303
15
7303en.book 16 ページ
2004年5月31日 月曜日 午前9時32分
Recording television programs
DVD indicator
2 1∫
5
1
1
The DVD indicator lights up on the unit.
2
OPEN/CLOSE
SD CARD
PC CARD
REC
EJECT
POWER
TIME SLIP
DVD
SD
PC
TIME SLIP
Recording
Time Slip indicator
TIME SLIP
DVD POWER
Numbered
buttons
/x1.3
DVD
≥Press the button again to close the tray.
CH
Insert label-up.
3
VOLUME
CH
DRIVE SELECT
2
3
3
SD/PC
4
5
6
7
8
CH
DVD - R AM
SP
CH
AUDIO
9
AUDIO
To select with the numbered buttons:
TV Mode (Airwaves)
CATV Mode (Cable)
e.g., 5: [0] ➡ [5]
e.g., 5:
[0] ➡ [0] ➡ [5]
15: [1] ➡ [5]
15: [0] ➡ [1] ➡ [5]
115: [1] ➡ [1] ➡ [5]
≥Select the audio to record (➡ page 17).
VCR Plus+ CM SKIP
SKIP
STOP
SLOW/SEARCH
PAUSE
PLAY/x1.3
1
∫
DIRECT NAVIGATOR
FUNCTIONS
FUNCTIONS
TOP MENU
RETURN
3421
ENTER
RETURN
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
TIME SLIP
ENTER
SUB MENU
SETUP
Info
ERASE REC MODE
REC
CHAPTER STATUS
4
When recording to DVD-R
≥When recording MTS broadcasts, only the audio selected in
“Select MTS” (➡ page 43) is recorded (“Main” or “SAP”).
≥In order to play a DVD-R recorded using this unit on another
playback source, the disc must first be finalized
(➡ page 41).
Preparation
Press [RETURN] to exit the television program list if it is displayed on
the television. To turn off auto start up of the television program list
➡ page 23, Selecting the TV Guide On ScreenTM system start up
pattern.
16
DVD - R AM
CH
Remaining time on the disc
4
5
[RAM] [DVD-R]
≥You can record up to 99 titles on one disc.
≥It is not possible to record continuously from one side of a double
sided disc to the other. You will need to eject the disc and turn it over.
≥When using 8 cm (3″ ) DVD-RAM, remove the disc from the cartridge.
≥It is not possible to record CPRM (➡ page 48) protected material
onto DVD-R or 2.8 GB DVD-RAM discs.
≥It is not possible to record to a card.
Press [REC MODE] to select the
recording mode (XP, SP, LP, or EP).
XP
≥To record sound using LPCM (XP mode only):
Set “Audio for XP Recording” to “LPCM” in the SETUP menu
(➡ page 44).
STATUS
RQT7303
Press [W X CH] to select the channel.
3
0
DIRECT
NAVIGATOR
Insert fully so it
clicks into place.
Insert with the arrow facing in.
PAGE
1
CANCEL
;
Press [< OPEN/CLOSE] on the main
unit to open the tray and insert a disc.
TV
POWER
INPUT SELECT TV/VIDEO
1
DRIVE SELECT
Press [DVD] to select the DVD drive.
5
Press [¥ REC] to start recording.
DVD - R AM
XP
REC
CH
Recording will take place on open space on disc. Data will not
be overwritten.
≥You cannot change the channel or recording mode during
recording.
∫ To stop recording
Press [∫].
From the start to the end of the recording is called one title.
[DVD-R]
It takes about 30 seconds for the unit to complete recording
management information after recording finishes.
∫ To pause recording
Press [;].
Press again to restart recording.
(Title is not split into separate titles.)
2004年5月31日 月曜日 午前9時32分
∫ To specify a time to stop recording—One Touch
Recording
Selecting audio to record
During recording
[RAM]
Press [¥ REC] to select the recording time.
Press [AUDIO].
Each time you press the button:
0:30 "# 1:00 "# 1:30 "# 2:00 "# 3:00 "# 4:00
^"""""""""""" Counter (cancel) ,"""""""""""}
≥This does not work during timer recordings (➡ page 19) or while
using Flexible Recording (➡ page 18).
To stop recording partway
Press [∫].
Off Timer
The unit switches to standby after about 6 hours in the stop mode.
You can turn this feature off or change the time to 2 hours
(➡ page 42, “Off Timer”).
Recording modes and approximate
recording times
Depending on the content being recorded, the recording times may
become shorter than indicated.
(Unit: hour)
DVD-RAM
DVD-R
(4.7 GB)
Mode
Single-sided Double-sided
(4.7 GB)
(9.4 GB)
XP (High quality)
1
2
1
SP (Normal)
2
4
2
LP (Long play)
4
8
Picture quality
EP (Extra long play)
§
8 (6 )
[.
l
l
l
l
l
a-
Stereo: Main audio (stereo)
≥If the broadcast is “MonoiSAP”, audio will be
v
monaural even if you select Stereo mode.
SAP:
v
Mono:
Secondary audio program (SAP)
≥If recorded in SAP mode, main audio is also
recorded.
Main audio (monaural)
≥Select “Mono” if reception is poor during a stereo
broadcast.
Recording
7303en.book 17 ページ
No disc
e.g., “Stereo” is selected
“((” appears when the unit is
receiving the audio type you
selected.
CH 12
(( Stereo
≥If you change the sound setting while recording, the recorded
sound will also change.
[DVD-R]
[RAM] (When recording sound in LPCM)
Select the audio (Main or SAP) in “Select
MTS” in the SETUP menu (➡ page 43).
4
§
16 (12 )
8 (6§)
XP
SP
LP
EP (6H)§
EP (8H)
Recording time
§
When “Recording Time in EP Mode” is set to “EP (6H)” in the
SETUP menu.
The sound quality is better when using “EP (6H)” than when using
“EP (8H)”.
[Note]
When recording to DVD-RAM using EP (8H) mode, play may not be
possible on DVD players that are compatible with DVD-RAM. In this
case use EP (6H) mode.
FR (Flexible Recording Mode)
The unit automatically selects a recording rate between XP and EP
(8H) that will enable the recordings to fit in the remaining disc space
with the best possible recording quality.
≥You can set when programming timer recordings.
≥All the recording modes from XP to EP appear in the
XP
display.
SP
LP
EP CH
RQT7303
17
7303en.book 18 ページ
2004年5月31日 月曜日 午前9時32分
Recording television programs
Refer to the control reference on page 16.
[RAM]
[RAM] [DVD-R]
Playing while you are recording
Recording
While recording to the DVD-RAM you can view the title being
recorded from the beginning as well as play a recorded title.
Playing from the beginning of the title you are
recording—Chasing playback
Flexible Recording
The unit sets the best possible picture quality that fits the recording
within the remaining disc space. The recording mode becomes FR
mode.
e.g.,
Recorded
Remain
45 minutes in
SP mode
Press [1] (PLAY).
Perfectly fit!
Time Slip indicator on the main unit lights.
Recording rate
between SP and LP
Playing a title previously recorded while recording—
Simultaneous rec and play
60 minutes
Program to be recorded
1
Press [DIRECT NAVIGATOR].
2
Press [3, 4, 2, 1] to select a title
and press [ENTER].
Preparation
≥Select the channel to record.
≥Press [DVD] to select the DVD drive.
1
Time Slip indicator on the main unit lights.
To exit the Direct Navigator screen
Press [DIRECT NAVIGATOR].
While stopped
Press [FUNCTIONS].
2
Reviewing the recorded images while recording—
Time Slip
Press [3, 4, 2, 1] to select
“FLEXIBLE RECORDING” and press
[ENTER].
FLEXIBLE REC
1
Record in FR mode
Maximum rec time
Set recording time
Press [TIME SLIP].
Start
Time Slip indicator on the main unit lights.
PLAY
0 min
Play starts from 30
seconds previous.
3
REC
The image currently being
recorded
≥You will hear the playback audio.
2
Press [3, 4] to select the time and
press [ENTER].
≥Press [TIME SLIP] to show the play images in full. Press
again to show the play and recording images.
∫ To stop play
Press [∫].
∫ To stop recording
2 seconds after play stops
Press [∫].
∫ To stop timer recording
Press [∫], then [ENTER] within 5 seconds.
≥You can also press and hold [∫] on the main unit for more than 3
seconds to stop recording.
RQT7303
18
3 Hour 00 Min.
3 Hour 00 Min.
Cancel
Press [2, 1] to select “Hour” and
“Min.” and press [3, 4] to set the
recording time.
≥You can also set the recording time with the numbered
buttons.
4
When you want to start recording
Press [3, 4, 2, 1] to select “Start”
and press [ENTER].
Recording starts.
To exit the screen without recording
Press [RETURN].
To stop recording partway
Press [∫].
To show the remaining time
Press [STATUS].
DVD-RAM
REC 0:59
CH71
Stereo
Remaining
time
7303en.book 19 ページ
2004年5月31日 月曜日 午前9時32分
Timer recording
Í DVD POWER
≥As long as the setting is not changed, the program is
recorded in the recording mode selected by the unit. To
change the setting ➡ below.
TV
POWER
INPUT SELECT TV/VIDEO
DVD
VOLUME
CH
SD/PC
DRIVE SELECT
PAGE
Numbered
buttons
1
2
3
4
5
6
PAGE WX CH
CH
∫ To change the setting
1Press [3] several times to select “LISTINGS”.
2Press [2, 1] to select “SCHEDULE”.
3Press [3, 4] to select the program and press
[ENTER].
AUDIO
7
8
9
Start early by :
End late by :
Quality :
VCR Plus+ CM SKIP
CANCEL
0
SKIP
STOP
∫
SLOW/SEARCH
PAUSE
PLAY/x1.3
1
DIRECT NAVIGATOR
DIRECT
NAVIGATOR
4Change the setting as necessary and press
[ENTER].
FUNCTIONS
≥To set recording to start early or end late
Press [3, 4] to select “Start early by” or “End late by” and
press the numbered buttons to enter minutes (up to 99).
TOP MENU
3421
ENTER
ENTER
SUB MENU
≥To change the recording mode
Press [3, 4] to select “Quality” and press the “Blue” button.
Each time you press the button:
LP # EP # FR # XP # SP
RETURN
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
TV GUIDE
PROG/CHECK
SETUP
“Blue” button
ERASE REC MODE
Info
^==============}
REC
“Green” button
(CHAPTER)
CHAPTER STATUS
4
Using the TV Guide On ScreenTM
system to make timer recordings
You can perform timer recording easily by just marking the desired
program(s) in a television program list.
≥You can enter up to 8 days in advance.
≥The program name becomes the recorded title if the program is
listed on the television program list.
Press [TV GUIDE].
SCHEDULE
TODAY
SORT
8:30PM
Last
Channel
87
NWGB
8:00 8:30
FAVORITES
RECORD
INFO.
pTV
TV
NWBG
ducation
2
Press [3, 4, 2, 1] to select the
program.
≥To skip one screen
Press [PAGE WX CH].
≥To skip 24 hours in the list
Press [3, 4, 2, 1] to select “LISTINGS” and:
Press the “Green” button (forward).
Press the “Blue” button (backward).
3
5
Press [Í DVD POWER] to turn the
unit off.
“F” lights on the unit’s display to indicate timer recording
standby has been activated.
\Note\
LISTINGS
8:00PM
Press [TV GUIDE].
The message “TURN RECORDER OFF FOR TIMER
RECORDING.” is shown on the television.
≥If the unit is already in the timer recording standby mode (if
“F” is already on the unit's display), the unit turns off
automatically. You need not take step 5 to complete the
procedure.
[RAM] [DVD-R]
1
00 minutes
00 minutes
SP
Recording
DVD POWER
Press the “Green” button.
“ R ” appears in the list to indicate that the program is set for
timer recording. If a program which is being broadcast at the
time is registered, timer recording will start immediately.
≥Press the “Green” button to cancel.
≥Press the “Blue” button to change recording frequency.
Each time you press the button:
[.
Records only once.
R
l
;
l
RR Records when the broadcast time and program
l
name match.
;
l
RW Records weekly.
l
l
;
{
Temporarily cancels the program timer
R
recording without deleting the program setting.
Repeat steps 2–3 to program other recordings.
≥Timer recording will work only if “F” is displayed.
≥“F” flashes when the unit cannot go to timer recording standby
(e.g., a recordable disc is not in the disc tray).
∫ Operations that can be performed during timer
recording standby
≥You can play discs. Do not press [Í DVD POWER] but [1] (PLAY)
or [DIRECT NAVIGATOR] instead. Timer recording works even
during disc play. [RAM]
≥You can add, change or delete programs scheduled for timer
recording. [RAM] [DVD-R]
–To add a scheduled program
1 Press [PROG/CHECK].
2 Press [3] to select “SCHEDULE”.
3 Press [2, 1] to select “LISTINGS”.
4 Press [4], then go to step 2 (➡ left).
–To change or delete a scheduled program (➡ page 22)
∫ To release the unit from recording standby
Press [Í DVD POWER].
The unit turns on and “F” goes out.
≥Be sure to press [Í DVD POWER] to return the unit to standby
mode before the scheduled recording time.
∫ To cancel recording when recording has already
begun
Press [∫], then [ENTER] within 5 seconds.
≥You can also press and hold [∫] on the main unit for more than 3
seconds to stop recording.
≥There may be some channels that are not displayed in the
television program list even if they are receivable. In this case set
them manually (➡ page 20).
To utilize TV Guide On ScreenTM system, see also page 23.
Notes on timer recording ➡ page 21
RQT7303
19
7303en.book 20 ページ
2004年5月31日 月曜日 午前9時32分
Timer recording
DVD POWER
Í DVD POWER
≥To enter the channel
Press [3, 4] to select “Channel” and press the numbered
buttons.
–To select the input channel (L1/L2/L3)
Press the “Blue” button.
≥To change the recording mode
Press [3, 4] to select “Quality” and press the “Blue” button.
Each time you press the button:
LP # EP # FR # XP # SP
TV
POWER
INPUT SELECT TV/VIDEO
DVD
VOLUME
CH
SD/PC
DRIVE SELECT
PAGE
Recording
Numbered
buttons
1
2
3
4
5
6
^==============}
CH
4
AUDIO
7
8
9
Press [ENTER].
VCR Plus+ CM SKIP
CANCEL
0
SKIP
STOP
PAUSE
PLAY/x1.3
∫
DIRECT
NAVIGATOR
MESSAGES SCHEDULE
VCR Plusr
SLOW/SEARCH
TOP MENU
SUB MENU
3421
ENTER
ERASE REC MODE
SETUP
Once
R
REMOVE
1:00
1:55
Sat
Sat
Sat
4/3
2:00pm
3:00pm
3:30pm
4:00pm
FREQUENCY
INFO.
Dodzilla
Once
Bull house Weekly
Be switched Weekly
Baseball
Once
R
RW
RW
R
Info
If the program to be recorded is currently on air, recording will
commence as soon as the program information has been
entered.
≥Press the “Green” button to change recording frequency.
Each time you press the button:
[.
Records only once.
R
l
;
l
RW Records weekly.
l
;
l
Records daily (From Monday to Friday).
RD
l
l
;
Temporarily cancels the program timer
{
R
recording without deleting the program setting.
TV GUIDE
REC
“Blue” button
“Green” button
(CHAPTER)
CHAPTER STATUS
Manually programming timer
recordings
1
NWBG
1:00pm
RETURN
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
PROG/CHECK
Sat
LISTINGS
SP
FUNCTIONS
ENTER
RECORD
87
NWBG
1
DIRECT NAVIGATOR
FAVORITES
5
Press [PROG/CHECK].
MESSAGES SCHEDULE
≥To program other recordings
Press [3, 4, 2, 1] to select “RECORD” and repeat steps
2–4.
FAVORITES
RECORD
Sat
Sat
Sat
4/3
Dodzilla
Once
Bull house Weekly
Be switched Weekly
Baseball
Once
SET TIMER
2:00pm
3:00pm
3:30pm
4:00pm
R
RW
RW
R
Press [TV GUIDE].
The message “TURN RECORDER OFF FOR TIMER
RECORDING.” is shown on the television.
≥If the unit is already in the timer recording standby mode (if
“F” is already on the unit's display), the unit turns off
automatically. You need not take step 6 to complete the
procedure.
LISTINGS
6
Press [Í DVD POWER] to turn the
unit off.
“F” lights on the unit’s display to indicate timer recording
standby has been activated.
2
3
RQT7303
20
Press the “Green” button.
Date :
Start Time :
End Time :
Channel :
Quality :
4 / 1 / 04
8 : 00 pm
10 : 00 pm
56
SP
PlusCode :
=========
Enter the settings.
\Note\
≥Timer recording will work only if “F” is displayed.
≥“F” flashes when the unit cannot go to timer recording standby
(e.g., a recordable disc is not in the disc tray).
∫ Operations that can be performed during timer
recording standby
≥You can play discs. Do not press [Í DVD POWER] but [1] (PLAY)
or [DIRECT NAVIGATOR] instead. Timer recording works even
during disc play. [RAM]
≥You can add, change or delete programs scheduled for timer
recording. [RAM] [DVD-R]
–To add a scheduled program (➡ step 1)
–To change or delete a scheduled program (➡ page 22)
∫ To release the unit from recording standby
≥To enter the date
Press [3, 4] to select “Date” and press the numbered
buttons.
(Date: Month/Day/Year)
Press [Í DVD POWER].
The unit turns on and “F” goes out.
≥Be sure to press [Í DVD POWER] to return the unit to standby
mode before the scheduled recording time.
≥To enter the time
Press [3, 4] to select “Start Time” or “End Time” and press
the numbered buttons.
–You can set up to 8 hours.
–To change am/pm
Press [2, 1] to select “am” or “pm” and press the “Blue”
button.
∫ To cancel recording when recording has already
begun
Press [∫], then [ENTER] within 5 seconds.
≥You can also press and hold [∫] on the main unit for more than 3
seconds to stop recording.
Notes on timer recording ➡ page 21
2004年5月31日 月曜日 午前9時32分
Using VCR Plusi system to make timer
recordings
Entering PlusCode® number is an easy way of timer recording. You
can find them in TV listings in newspapers and magazines.
≥You can enter up to 8 days in advance.
≥VCR Plusi system works only after this unit downloads the
television program list (➡ page 10).
1
2
3
Press [VCR Plusr].
Date :
Start Time :
End Time :
Channel :
Quality :
4 / 1 / 04
8 : 00 pm
10 : 00 pm
56
SP
PlusCode :
=========
∫ Operations that can be performed during timer
recording standby
≥You can play discs. Do not press [Í DVD POWER] but [1] (PLAY)
or [DIRECT NAVIGATOR] instead. Timer recording works even
during disc play. [RAM]
≥You can add, change or delete programs scheduled for timer
recording. [RAM] [DVD-R]
–To add a scheduled program (➡step 1)
–To change or delete a scheduled program (➡ page 22)
∫ To release the unit from recording standby
Press [Í DVD POWER].
The unit turns on and “F” goes out.
≥Be sure to press [Í DVD POWER] to return the unit to standby
mode before the scheduled recording time.
Recording
7303en.book 21 ページ
∫ To cancel recording when recording has already
begun
Press [∫], then [ENTER] within 5 seconds.
≥You can also press and hold [∫] on the main unit for more than 3
seconds to stop recording.
Press [3, 4] to select “PlusCode”.
Press the numbered buttons to enter
the PlusCode number.
≥To correct the number
Press [3] and press [4]. Enter the number again from the
beginning.
4
Press [ENTER].
If a program which is being broadcast at the time is registered,
timer recording will start immediately.
MESSAGES SCHEDULE
FAVORITES
RECORD
Sat
NWBG
1:00pm
LISTINGS
Once
R
87
NWBG
SP
REMOVE
1:00
1:55
Sat
Sat
Sat
4/3
2:00pm
3:00pm
3:30pm
4:00pm
FREQUENCY
INFO.
Dodzilla
Once
Bull house Weekly
Be switched Weekly
Baseball
Once
R
RW
RW
R
Repeat steps 1–4 to program other recordings.
≥As long as the setting is not changed, the program is
recorded in the recording mode selected by the unit. To
change the setting ➡ page 19, To change the setting, steps
3–4.
5
Press [TV GUIDE].
The message “TURN RECORDER OFF FOR TIMER
RECORDING.” is shown on the television.
≥If the unit is already in the timer recording standby mode (if
“F” is already on the unit's display), the unit turns off
automatically. You need not take step 6 to complete the
procedure.
6
Press [Í DVD POWER] to turn the
unit off.
“F” lights on the unit’s display to indicate timer recording
standby has been activated.
∫ Even if you have forgotten to set the timer
recording standby mode
Two minutes before the time when the timer recording is
scheduled to commence, the unit automatically turns off and will
be placed in the standby mode. (The “F” appears on the display.)
If play or recording is being performed, it will be interrupted.
Notes on timer recording
≥When you program successive timer recordings to start
immediately one after the other, the unit cannot record the part
at the ending of the earlier program (approximately 15
seconds). In addition, when recording to DVD-R, the unit
cannot record the part at the beginning of the later program
(approximately 15 seconds).
Program
Program
Not recorded [DVD-R]
\Note\
≥Timer recording will work only if “F” is displayed.
≥“F” flashes when the unit cannot go to timer recording standby
(e.g., a recordable disc is not in the disc tray).
Recorded
Recorded
Not recorded
≥If you set DST (Daylight Saving Time) to ON when manually
setting the clock (➡ page 11), timer recording may not work
when summer switches to winter and vice versa.
RQT7303
21
7303en.book 22 ページ
2004年5月31日 月曜日 午前9時32分
Timer recording
∫ To change the recording frequency
DVD POWER
Í DVD POWER
Press the “Green” button.
TV
POWER
DVD
∫ To change the time and recording mode
VOLUME
CH
INPUT SELECT TV/VIDEO
1 Press [ENTER].
SD/PC
DRIVE SELECT
PAGE
1
Recording
Numbered
buttons
2
3
PAGE WX CH
CH
4
5
6
7
8
9
Start early by :
End late by :
Quality :
00 minutes
00 minutes
SP
AUDIO
2 Change the setting as necessary and press [ENTER].
≥To set recording to start early or end late
Press [3, 4] to select “Start early by” or “End late by” and
press the numbered buttons to enter minutes (up to 99).
VCR Plus+ CM SKIP
CANCEL
0
SKIP
STOP
SLOW/SEARCH
PAUSE
PLAY/x1.3
DIRECT NAVIGATOR
FUNCTIONS
TOP MENU
3421
ENTER
ENTER
SUB MENU
≥To change the recording mode
Press [3, 4] to select “Quality” and press the “Blue” button.
Each time you press the button:
LP # EP # FR # XP # SP
^==============}
RETURN
∫ To delete the program
Press the “Blue” button.
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
PROG/CHECK
ERASE REC MODE
SETUP
“Blue” button
Info
Info
TV GUIDE
∫ To exit the screen
REC
“Green” button
(CHAPTER)
CHAPTER STATUS
Press [TV GUIDE].
The message “TURN RECORDER OFF FOR TIMER
RECORDING.” is shown on the television.
≥If the unit is already in the timer recording standby mode (if “F” is
already on the unit's display), the unit turns off automatically.
∫ To put the unit on timer recording standby
Check, change or delete a program
1
∫ When there is a duplicate or overlapping
program timer recording
Press [PROG/CHECK].
MESSAGES SCHEDULE
The program timer recording that was set last is recorded. None of
the program that was set earlier is recorded even if there is only
partial overlapping.
Program timer recordings that are not recorded are highlighted in
grey.
Time
LISTINGS
FAVORITES
RECORD
Sat
Sat
Sat
Sat
4/3
Once
NWBG
Dodzilla
Once
Bull house Weekly
Be switched Weekly
Baseball
Once
SET TIMER
1:00pm
2:00pm
3:00pm
3:30pm
4:00pm
Press [Í DVD POWER] to turn the unit off.
“F” lights on the unit’s display to indicate timer recording standby
has been activated.
R
Not recorded
R
RW
RW
R
Programs set earlier
Not recorded
Program set last
2
Press [3, 4] to select the program.
Channel or program name (a program name that was set
for timer recording using TV Guide On ScreenTM system
or VCR Plusi system that was listed in the program list)
Sat 1:00pm
NWBG
Once
R
87
NWBG
SP
1:00
1:55
REMOVE
FREQUENCY
Recording mode (➡ page 17)
RQT7303
22
INFO.
Frequency (➡ page 19, 20)
Recorded
7303en.book 23 ページ
2004年5月31日 月曜日 午前9時32分
Utilizing TV Guide On ScreenTM system
∫ Customizing the channel line-up
Press [TV GUIDE].
1 Press [3] several times to select “LISTINGS”.
2 Press [2, 1] to select “SETUP” and press [4].
3 Press [3, 4] to select “Change channel display” and press
[ENTER].
4 Press [3, 4] to select the channel.
≥Press [PAGE WX CH] to skip one screen.
SCHEDULE
TODAY
LISTINGS
8:00PM
SORT
8:30PM
Last
Channel
Advertisements
87
NWGB
8:00 8:30
FAVORITES
RECORD
INFO.
Information
window
To hide the channel
Press the “Green” button to select “OFF”.
R
pTV
TV
Icons NWBG
Stereo
Closed caption
R
Re-run
pTV
2 ON
PTV-S
ducation
CANCEL
BOX
ANiMe
Network
PBS
TV
NWBG
On-screen guidance
The functions of the “Green” and “Blue” buttons on
the remote control are displayed.
Programs are categorized by color.
Green:
Sports
Blue:
Children’s
Purple:
Movies
Teal:
Other categories
∫ Selecting the program from the desired program
category and setting timer recording
1
2
3
4
Press [3] several times to select “LISTINGS”.
Press [2, 1] to select “SORT” and press [4].
Press [2, 1] to select the major category and press [4].
Press [3, 4, 2, 1] to select the minor category and press
[ENTER].
5 Press [3, 4, 2, 1] to select.
≥When sorting alphabetically, press [ENTER] and [3, 4] to
select.
6 Press the “Green” button.
∫ Changing the size of information window
ducation
ON/OFF
INFO.
5 ON
12 ON
22 ON
TV-TR
NWBG
EDU
To change the channel number
Press the numbered buttons.
e.g. 1:
[0] ➡ [0] ➡ [1]
15: [0] ➡ [1] ➡ [5]
115: [1] ➡ [1] ➡ [5]
To change the order of the channels
1 Press [2].
2 Press the “Blue” button to move up or the “Green” button to
move down.
pTV
MOVE UP
TV
NWBG
ducation
2 ON
PTV-S
MOVE DOWN
TV-TR
NWBG
EDU
INFO.
5 ON
12 ON
22 ON
Repeat step 4 as necessary.
Press [Info] while the program is highlighted.
5 Press [TV GUIDE].
∫ Adjusting the channel line-up
∫ Registering a program you don’t want to miss as
a “Favorite”
If the television program list’s channel line-up differs from what you
were expecting, perform the following steps.
1 Press [3] several times to select “LISTINGS”.
2 Press [2, 1] to select “SETUP” and press [4].
3 Press [3, 4] to select “Change system settings” and press
[ENTER].
4 Press [3, 4] to select “Yes, but my channel line-up is incorrect”
and press [ENTER].
≥When there is more than one cable network transmitting television
program listings in the area where you are living, more than one
channel line-up is displayed. Press [3, 4] to select one and then
press [ENTER].
≥Alternatively, you can customize the channel line-up in the Channel
Editor (➡ right, Customizing the channel line-up). Press [3, 4] to
select “No Match” and then press [ENTER].
∫ Selecting the TV Guide On ScreenTM system
start up pattern
1
2
3
4
Press [3] several times to select “LISTINGS”.
Press [2, 1] to select “SETUP” and press [4].
Press [3, 4] to select “Review options” and press [ENTER].
Press [3, 4] to select the option and press [ENTER].
≥On: Turns on auto start up.
≥Off: Turns off auto start up.
∫ Reading messages
You may receive messages regarding new TV Guide On
ScreenTM system functions or special promotions. When there
are unread messages, an envelope-shaped icon appears at the
upper left of the screen.
1 Press [3] several times to select “LISTINGS”.
2 Press [2, 1] to select “MESSAGES” and press [4].
3 Press [3, 4] to select the message and press [Info].
≥To delete unwanted messages press the “Green” button.
≥Messages are automatically deleted after 60 days.
≥The ID number appears at the end of the list.
Recording
Program viewed before the
program list was opened.
By registering a program as “Favorite” in advance, you can later tune
to that program quickly by pressing the “Blue” button when that
program begins broadcasting.
When you cannot remember the television program you want to
watch, we recommend you press the “Blue” button when the
television reception screen is displayed. This unit may tune in your
“Favorite” program.
1 Press [TV GUIDE].
2 Press [3, 4, 2, 1] to select the program.
3 Press the “Blue” button.
“
” appears in the list to indicate that the program is set as a
“Favorite”.
≥Press the “Green” button to change the frequency.
Each time you press the button:
[.
Registers as “Favorite” only once.
l
;
l
A program becomes a “Favorite” when the
R broadcast time and program name match.
l
l
;
Registers as “Favorite” weekly.
l
W
l
;
l
“Favorite” registration temporarily off.
{
≥Press the “Blue” button to cancel.
Repeat steps 2–3 to set other programs.
≥When there is more than one program registered as “Favorite” in
the same time frame, each time you press the “Blue” button, the
program switches to the other.
∫ Viewing TV Guide On ScreenTM system
explanations and promotions
1 Press [3] several times to select “LISTINGS”.
2 Press [2, 1] to select “PROMOTIONS” and press [4].
3 Press [3, 4] to select and press [Info].
RQT7303
23
7303en.book 24 ページ
2004年5月31日 月曜日 午前9時32分
Playing recorded video contents/Playing play-only discs
3
DVD indicator
2 1∫ 3
OPEN/CLOSE
SD CARD
PC CARD
REC
EJECT
POWER
TIME SLIP
DVD
SD
PC
DRIVE SELECT
TIME SLIP
DVD POWER
TIME SLIP
WX CH
45
TV
POWER
INPUT SELECT TV/VIDEO
/x1.3
CH
Playing back
1
Numbered
buttons
DVD
DRIVE SELECT
SD/PC
∫ Selecting recorded programs (titles) to play–
Direct Navigator
:9
;
∫
2
3
4
5
6
7
8
CH
SKIP
STOP
SLOW/SEARCH
PAUSE
PLAY/x1.3
TOP MENU
Info
RETURN
ERASE REC MODE
TIME SLIP
REC
CHAPTER STATUS
CHAPTER
Preparation
Press [RETURN] to exit the television program list if it is displayed on
the television. To turn off auto start up of the television program list
➡ page 23, Selecting the TV Guide On ScreenTM system start up
pattern.
2
10 10/27 Mon
8 10/27 Mon
--
--
--
Play
02/02
SUB MENU
Next
Select
2 Press [3, 4, 2, 1] to select “VIDEO” tab and
press [ENTER].
DIRECT NAVIGATOR
DVD-RAM
Title View
07
08
10 10/27 Mon
8 10/27 Mon
VIDEO PICTURE
---
RETURN
≥It is not possible to play continuously from one side of a double
sided disc to the other. You will need to eject the disc and turn it
over.
≥When using 8 cm (3″ ) DVD-RAM, remove the disc from the
cartridge.
1
08
Previous
3
3421
ENTER
2; ;1
SUB MENU
SETUP
VIDEO PICTURE
--
07
65
FUNCTIONS
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
ERASE
AUDIO
Title View
CM SKIP
ENTER
SUB MENU
W X CH
AUDIO
9
VCR Plus+ CM SKIP
DIRECT NAVIGATOR
DIRECT NAVIGATOR
TOP MENU
DIRECT NAVIGATOR
DVD-RAM
PAGE
1
0
3 Press [3, 4, 2, 1] to select the title and press
[ENTER].
You can also select titles with the numbered buttons.
e.g.,
5:
[0] ➡ [5]
15:
[1] ➡ [5]
To show other pages
Press [3, 4, 2, 1] to select “Previous” or “Next” and press
[ENTER].
≥You can also press [:, 9] to show other pages.
To exit the screen
Press [DIRECT NAVIGATOR].
Direct Navigator screen icons
Title protected.
Title that was not recorded due to recording protection
(Digital broadcasts, etc.)
Press [DVD] to select the DVD drive.
t
Title cannot be played because data is damaged etc.
The DVD indicator lights up on the unit.
[
Currently recording.
Press [< OPEN/CLOSE] on the main
unit to open the tray and insert a disc.
≥Press the button again to close the tray.
Insert label-up.
Title with “One time only recording” restriction
∫ When a menu screen appears on the television
Insert fully so it
clicks into place.
Insert with the arrow facing in.
24
PLAY
[RAM] [DVD-R]
Play starts from the most recently
recorded title.
[DVD-A] [DVD-V] [VCD] [CD]
Play starts from the beginning of the disc.
1 Press [DIRECT NAVIGATOR].
CANCEL
RQT7303
DVD - R AM
[RAM] [DVD-R]
VOLUME
CH
Press [1] (PLAY).
[DVD-A] [DVD-V]
Press [3, 4, 2, 1] to select the item and press [ENTER].
Some items can also be selected using the numbered buttons.
[VCD]
Press the numbered buttons to select the item.
e.g., 5:
[0] ➡ [5]
15: [1] ➡ [5]
≥To return to the menu screen
[DVD-A] Press [TOP MENU].
[DVD-V] Press [TOP MENU] or [SUB MENU].
[VCD] Press [RETURN].
7303en.book 25 ページ
2004年5月31日 月曜日 午前9時32分
Operations during play
Press [∫].
Pause
PLAY
Press [;].
Press again to restart play.
Press [6] or [5].
Search
Skip
≥On the main unit, press and hold [D] or [E].
≥The speed increases up to 5 steps.
≥Press [1] (PLAY) to restart play.
≥Audio is heard during first level search forward.
You can turn off the sound during search (➡ page 43, “Search Audio & PLAY k1.3”).
Audio is heard during all levels of search. [DVD-A] (excluding moving picture parts) [CD]
Playing back
Stop
DVD - R AM
The stopped position is memorized.
“PLAY” flashes in the unit’s display. (Excluding when playing from the Direct
Navigator and when playing a play list.)
Resume play function
Press [1] (PLAY) to restart from this position.
Press [:] or [9].
≥On the main unit, press [D] or [E].
≥Each press increases the number of skips.
Press the numbered buttons.
e.g., 5:
15:
Starting from a
selected item
[0] ➡ [5]
[1] ➡ [5]
[CD] (MP3 discs only)
5:
15:
[0] ➡ [0] ➡ [5]
[0] ➡ [1] ➡ [5]
[DVD-A] Selecting groups
While stopped (screen saver is displayed on the television ➡ right)
5:
[5]
≥This works only when stopped (screen saver is displayed on the television
➡ right) with some discs.
Quick View
Press and hold [1] (PLAY/a1.3).
[RAM]
The play speed can be increased
without distorting the audio.
≥Press again to return to normal speed.
≥This does not work if the setting is “Off” in “Search Audio & PLAY k1.3” (➡ page 43).
While paused, press [6] or [5].
Slow-motion
[RAM] [DVD-R] [DVD-A] (Motion
picture parts only) [DVD-V] [VCD]
Frame-by-frame
[RAM] [DVD-R] [DVD-A] (Motion
picture parts only) [DVD-V] [VCD]
Displaying the
television image as a
picture-in-picture
Skipping the specified
time (Time Slip)
[RAM] [DVD-R]
CM Skip
≥On the main unit, press and hold [D] or [E].
≥The speed increases up to 5 steps.
≥Press [1] (PLAY) to restart play.
≥Forward direction only. [VCD]
≥The unit will pause if slow-motion play is continued for 5 minutes.
While paused, press [2;] or [;1].
≥Each press shows the next frame.
≥Press [1] (PLAY) to restart play.
≥Forward direction only. [VCD]
Press [TIME SLIP].
The unit displays the television image as a
picture-in-picture.
≥You will hear the playback audio.
≥Press [TIME SLIP] again to cancel.
≥The blue background does not appear on the
receiving screen even if you select “On” from
the “Blue Background” in the SETUP menu
(➡ page 44).
Play images
Current receiving images
≥You can change the channel being received by
pressing [W X CH].
≥You cannot change the channel being received
while recording.
1 Press [TIME SLIP].
2 Press [3, 4] to select the time and press [ENTER].
Play skips the specified time.
≥Press [TIME SLIP] to show the play images in full.
Press [CM SKIP].
[RAM] [DVD-R]
Play restarts from approximately a
minute later.
RQT7303
25
7303en.book 26 ページ
2004年5月31日 月曜日 午前9時32分
Playing recorded video contents/Playing play-only discs
Refer to the control reference on page 24.
Editing operations during play
Playing back
Erase
1 Press [ERASE].
2 Press [2, 1] to select “Erase” and press [ENTER].
[RAM] [DVD-R]
≥A title cannot be restored once it is erased. Make certain before proceeding.
≥You cannot erase while recording and playing at the same time.
Create chapters
Press [CHAPTER].
(➡ page 32, Title/Chapter)
[RAM]
≥Press [:, 9] to skip to the start of a chapter.
≥You cannot divide while recording and playing at the same time.
Changing audio during play
Press [AUDIO].
[RAM] [VCD]
LR>L>R
^---------------}
DVD-RAM
PLAY
e.g., “L R” is selected
≥When playing an SAP broadcast recorded on DVD-RAM:
MAIN()SAP
LR
[DVD-A] [DVD-V]
You can change the audio channel number each time you press the
button. This allows you to change things like the soundtrack
language (➡ page 30, Sound track).
Sound track
1 ENG
e.g., English is selected.
[Note]
You cannot change the audio type in the following cases.
≥When a DVD-R disc is in the disc tray while DVD drive is selected.
≥When the recording mode is XP and “Audio for XP Recording” is set to “LPCM” (➡ page 44).
RQT7303
26
Î Digital 3/2.1ch
7303en.book 27 ページ
2004年5月31日 月曜日 午前9時32分
Using menus to play MP3
Using the tree screen to find a group
DVD POWER
While the file list is displayed
TV
POWER
INPUT SELECT TV/VIDEO
DVD
Press [1] while a track is highlighted
to display the tree screen.
SD/PC
DRIVE SELECT
Selected group No. /Total groups
If the group has no track, “– –” is displayed
as group number.
PAGE
Numbered
buttons
1
2
3
4
5
6
CH
AUDIO
7
8
MENU
G
8
T
14
TOTAL
40/111
9
VCR Plus+ CM SKIP
CANCEL
0
SKIP
STOP
SLOW/SEARCH
PAUSE
No.
0 – 9
PLAY/x1.3
DIRECT NAVIGATOR
FUNCTIONS
TOP MENU
TREE
MP3 music
G 7/25
001 My favorite
001 Brazilian pops
002 Chinese pops
003 Czech pops
004 Hungarian pops
005 Liner notes
006 Japanese pops
007 Mexican pops
008 Philippine pops
009 Swedish pops
001 Momoko
002 Standard number
001 Piano solo
002 Vocal
You cannot select groups
that contain no compatible
files.
TOP MENU
3421
ENTER
ENTER
SUB MENU
RETURN
RETURN
2
Press [3, 4, 2, 1] to select a group
and press [ENTER].
Playing back
DVD
1
VOLUME
CH
The file list for the group appears.
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
SETUP
Info
ERASE REC MODE
To return to the file list
Press [RETURN].
REC
CHAPTER STATUS
[CD] (MP3 discs only)
This unit plays MP3 files recorded on CD-R/RW designed for audio
recording that are finalized (➡ page 48) on a computer. Files are
treated as tracks and folders are treated as groups.
Preparation
Press [DVD] to select the DVD drive.
1
Press [TOP MENU].
Selected group
G: Group No.
T: Track No. in the group
TOTAL: Track No./Total
tracks in all groups
MENU
G
1
T
1
TOTAL
1/111
No.
0 – 9
No.
GROUP
1 : My favorite
TOTAL
TRACK
TREE
001 Both Ends Freezing
1
002 Lady Starfish
2
003 Life on Jupiter
3
004 Metal Glue
4
005 Paint It Yellow
5
006 Pyjamamama
6
007 Shrimps from Mars
7
008 Starperson
8
009 Velvet Cuppermine
9
010 Ziggy Starfish
10
Prev.
2
Tips for making MP3 discs
≥Discs must conform to ISO9660 level 1 or 2 (except for
extended formats).
≥Compatible compression rate: between 32 kbps and 320 kbps
≥Compatible sampling rate:
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz and 48 kHz
≥Maximum number of tracks and groups recognizable:
999 tracks and 99 groups
≥This unit is compatible with multi-session.
≥This unit is not compatible with ID3 tags or packet writing.
≥Depending on recording, some items may not be playable.
≥Reading or play of the disc may take time if there are a lot of still
pictures or sessions.
≥The display order may differ from how the order is displayed on
a computer.
Next
Press [3, 4] to select the track and
press [ENTER].
Naming folders and files
≥MP3 files must have the
extension “.MP3” or “.mp3”.
≥At the time of recording, give
folder and file names a 3-digit
numeric prefix in the order you
want them to play (this may not
work at times).
≥English alphabets and Arabic
numerals are displayed
correctly. Other characters may
not be displayed correctly.
e.g.,
Root
001
001 (folder=group)
001track.mp3 (file=track)
002track.mp3
003track.mp3
002 group
003 group
001track.mp3
002track.mp3
003track.mp3
004track.mp3
001track.mp3
002track.mp3
003track.mp3
Order of play
Play continues to the last track in the last group.
≥“0” indicates the track currently playing.
≥You can also select the track with the numbered buttons.
e.g., 5: [0] ➡ [0] ➡ [5]
15: [0] ➡ [1] ➡ [5]
To show other pages
Press [3, 4, 2, 1] to select “Prev.” or “Next” and press [ENTER].
After listing all the tracks in one group, the list for the next group
appears.
To exit the screen
Press [TOP MENU].
RQT7303
27
7303en.book 28 ページ
2004年5月31日 月曜日 午前9時32分
Playing still pictures
PC card slot
DRIVE SELECT
OPEN/CLOSE
SD CARD
PC CARD
REC
EJECT
POWER
TIME SLIP
DVD
SD
PC
TIME SLIP
DRIVE SELECT
/x1.3
CH
DVD, SD, PC indicator
SD card slot
∫
DVD POWER
TV
POWER
INPUT SELECT TV/VIDEO
Inserting/Removing the SD/PC card
Only insert or remove the SD/PC card after turning the unit off.
When the card indicator (“SD” or “PC”) on the unit’s display is
flashing, the card is being read from or written to. Do not turn off the
unit or remove the card. Such action may result in malfunction or
loss of the card’s contents.
∫ SD card slot
Inserting the card
VOLUME
CH
Insert straight-in until it fits
into space.
EJECT
PC CARD
Playing back
DVD
DRIVE SELECT
SD/PC
DVD, SD/PC
POWER
PAGE
Numbered
buttons
1
2
3
4
5
6
7
8
SD CARD
CH
Insert label up with cut-off corner at the right.
AUDIO
9
VCR Plus+ CM SKIP
CANCEL
0
SKIP
STOP
Removing the card
SLOW/SEARCH
PAUSE
PLAY/x1.3
∫
EJECT
PC CARD
DIRECT NAVIGATOR
DIRECT
NAVIGATOR
SD CARD
FUNCTIONS
POWER
1 Press on the center of the card.
TOP MENU
3421
ENTER
ENTER
SUB MENU
2 Draw straight out.
RETURN
SUB MENU
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
SETUP
ERASE REC MODE
∫ PC card slot
Inserting the card
There are cards requiring adaptors (➡ page 15).
REC
ERASE
Info
CHAPTER STATUS
STATUS
Hold the edge of the card and insert until it fits
into place.
≥If using the adaptor, do not press directly on
the card.
EJECT
PC CARD
SD CARD
2
POWER
Regarding still pictures (JPEG, TIFF)
≥Compatible formats:DCF§ compliant (Content recorded on a
digital camera etc.)
§
Design rule for Camera File system: unified standard
established by Japan Electronics and Information Technology
Industries Association (JEITA).
≥File format: JPEG, TIFF (non-compressed RGB chunky format)
≥Number of pixels: 34k34 to 6144k4096
(Sub sampling is 4:2:2 or 4:2:0)
≥This unit can handle a maximum of 3000 files and 300 folders
(including higher folders).
≥Operation may take time to complete when playing TIFF format
still pictures, or when there are many files and/or folders, some
files may not display or be playable.
≥MOTION JPEG is not supported.
2 align to match
the mark
1
The labeled side facing upwards
Terminal connections facing into the unit
Removing the card
Eject button
comes out
1 Push
EJECT
2
Push again
EJECT
PC CARD
PC CARD
EJECT
PC CARD
EJECT
PC CARD
SD CARD
POWER
≥If using the adaptor, remove the adaptor and card together.
RQT7303
28
7303en.book 29 ページ
2004年5月31日 月曜日 午前9時32分
∫ To select the still pictures in another folder
1
Press [DVD] or [SD/PC] to select the
drive.
≥Each time you press [SD/PC]:
SD card drive ,". PC card drive
≥On the main unit, press
[DRIVE SELECT] several times.
The indicator lights up on the unit.
2
e.g., SD card drive
Picture (JPEG) View
PICTURE
SD CARD
Folder
100__DVD
0001
0002
0003
0004
0005
0006
0007
0008
0009
----
----
----
\DCIM
DIRECT NAVIGATOR Picture (JPEG) View
PICTURE
SD CARD
Folder
DVD
SD
103__DVD
0001
0002
0003
0004
0005
0006
0007
0008
PC
Press [DIRECT NAVIGATOR].
DIRECT NAVIGATOR
(➡ page 15, Structure of folders displayed by this unit)
1 Press [3, 4, 2, 1] to select “Folder” and press
[ENTER].
2 Press [3, 4] to select the folder and press [ENTER].
Picture (JPEG) View
screen
\DCIM\100__DVD
001 100__DVD
002 101__DVD
003 102__DVD
004 103__DVD
-----
You can also select folders with the numbered buttons.
e.g.,
5:
[0] ➡ [0] ➡ [5]
15:
[0] ➡ [1] ➡ [5]
115:
[1] ➡ [1] ➡ [5]
≥If there is a multiple number of higher folders recognizable,
you can switch them using [2, 1].
\DCIM
Previous
ENTER
3
4
SUB MENU
001/001
001 100__DVD
002 101__DVD
003 102 DVD
Next
Select
Playing back
[RAM] [SD] [PC]
∫ To show the picture properties
Press [STATUS] twice.
[RAM]
Press [3, 4, 2, 1] to select
“PICTURE” tab and press [ENTER].
Press [3, 4, 2, 1] to select the still
picture and press [ENTER].
You can also select still pictures with the numbered buttons.
e.g.,
5:
[0] ➡ [0] ➡ [0] ➡ [5]
115: [0] ➡ [1] ➡ [1] ➡ [5]
15: [0] ➡ [0] ➡ [1] ➡ [5]
1115: [1] ➡ [1] ➡ [1] ➡ [5]
≥Press [2, 1] to display the previous or next still picture.
≥Useful functions during still picture play (➡ below).
Shooting data
11 / 10 6:53 PM
Folder - Picture No. 102 - 0001
Date 11 / 12 / 2003
No.
3/ 9
To exit the picture properties screen
Press [STATUS].
[Note]
≥Still pictures cannot be played during recording.
≥DVD is always selected as the drive when the unit is turned off and
then turned back on.
To stop playing
Press [∫]
To exit the screen
Press [DIRECT NAVIGATOR].
Useful functions during still picture play
[RAM] [SD] [PC]
Start Slide Show
Slide Interval
You can display still pictures one by one with constant interval.
While the Picture (JPEG) View screen is displayed
1 Press [SUB MENU].
2 Press [3, 4] to select “Start Slide Show” and press
[ENTER].
Erase Picture
Set up Protection
Cancel Protection
DPOF
Start Slide Show
≥To change the display timing
1 Press [3, 4] to select “Slide Interval” in step 2 and press [ENTER].
2 Press [2, 1] to select the desired timing (0–30 seconds) and press [ENTER].
Rotate
1 Press [SUB MENU].
2 Press [3, 4] to select “Rotate RIGHT” or “Rotate LEFT”
and press [ENTER].
Slide Interval
Rotate RIGHT
Rotate LEFT
≥Rotation information will not be stored.
Zoom in
Zoom out
(Only for a still picture with a low
pixel count)
Erase
1 Press [SUB MENU].
2 Press [3, 4] to select “Zoom in” and press [ENTER].
≥To return the picture to its original size, press [3, 4] to select “Zoom out” in step 2
and press [ENTER].
≥When zooming in, the picture may be cut off.
≥The enlargement information will not be stored.
Rotate RIGHT
Rotate LEFT
Zoom in
1 Press [ERASE].
2 Press [2, 1] to select “Erase” and press [ENTER].
≥Once erased, the recorded contents are lost and cannot be restored. Make certain before
proceeding.
RQT7303
29
7303en.book 30 ページ
2004年5月31日 月曜日 午前9時32分
Using on-screen menus and Status messages
Disc menu–Setting the disc content
DVD POWER
TV
POWER
DVD
DRIVE SELECT
Sound track§
VOLUME
CH
INPUT SELECT TV/VIDEO
[RAM] [DVD-R]
The disc’s audio attributes appear.
[DVD-A] [DVD-V]
Select the audio and language (➡ below, Audio attribute,
Language).
SD/PC
PAGE
1
2
3
4
5
6
7
8
CH
AUDIO
9
Subtitle§
[RAM] [DVD-R] (Only discs that contain subtitle on/off information)
[DVD-A] [DVD-V]
VCR Plus+ CM SKIP
CANCEL
0
Playing back
SKIP
STOP
SLOW/SEARCH
PAUSE
Turn the subtitle on/off and select the language (➡ below,
Language).
≥Subtitle on/off information cannot be recorded using this
unit. [RAM] [DVD-R]
≥If the subtitles overlap closed captions recorded on discs,
turn the subtitles off.
PLAY/x1.3
DIRECT NAVIGATOR
FUNCTIONS
TOP MENU
3421
ENTER
ENTER
SUB MENU
Audio channel [RAM] [VCD]
RETURN
DISPLAY
➡ page 26, Changing audio during play
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
Angle§ [DVD-A] [DVD-V]
SETUP
ERASE REC MODE
Info
REC
CHAPTER STATUS
STILL-P (Still picture) [DVD-A]
STATUS
Selects the play method for still pictures.
Slide Show:Plays according to the default order on the disc.
Page:
Select the still picture number and play.
≥RANDOM: Plays in random order.
≥Return:
Returns to the default still picture on the disc.
PBC (Playback control ➡ page 48) [VCD]
On-screen menus
1
Indicates whether menu play (playback control) is on or off.
Press [DISPLAY].
Disc
Play
Video
Audio
Menu
Sound track
§
1
Î Digital 2/0 ch
Subtitle
OFF
Audio channel
LR
Item
Setting
≥Depending on the condition of the unit (playing, stopped,
etc.) and disc contents, there are some items that you
cannot select or change.
2
3
4
Press [3, 4] to select the menu and
press [1].
Press [3, 4] to select the item and
press [1].
Press [3, 4] to select the setting.
≥Some items can be changed by pressing [ENTER].
To clear the on-screen menus
Press [DISPLAY].
RQT7303
30
You may have to use the menus (➡ page 24) on the disc to make
changes.
≥The display changes according to the disc content. You cannot
change when there is no recording.
Audio attribute
LPCM/PPCM/ÎDigital/DTS/MPEG:
Signal type
k (kHz):
Sampling frequency
b (bit):
Number of bits
ch (channel):
Number of channels
Language
ENG:
FRA:
DEU:
ITA:
ESP:
NLD:
English
French
German
Italian
Spanish
Dutch
SVE:
NOR:
DAN:
POR:
RUS:
JPN:
Swedish
Norwegian
Danish
Portuguese
Russian
Japanese
CHI:
KOR:
MAL:
VIE:
THA:
¢:
Chinese
Korean
Malay
Vietnamese
Thai
Others
7303en.book 31 ページ
2004年5月31日 月曜日 午前9時32分
Play menu–Change the play sequence
Audio menu–Change the sound effect
This function works only when the elapsed play time is displayed.
≥All
[VCD] [CD] (excluding MP3 discs)
≥Chapter
[RAM] [DVD-R] [DVD-V]
≥Group
[DVD-A] [CD] (MP3 discs only)
≥PL (Play list) [RAM]
≥Title
[RAM] [DVD-R] [DVD-V]
≥Track
[DVD-A] [VCD] [CD]
Select “OFF” to cancel.
V.S.S. [RAM] [DVD-R] [DVD-V]
(Dolby Digital , 2-channel or over only)
Enjoy a surround-like effect if you are using two front
speakers only.
≥Turn V.S.S. off if it causes distortion.
≥V.S.S. does not work for SAP recordings.
Dialog Enhancer [DVD-A] [DVD-V]
(Dolby Digital, 3-channel or over only, including a center channel)
The volume of the center channel is raised to make dialog
easier to hear.
Video menu–Change the picture quality
Picture
≥Normal:
≥Soft:
≥Fine:
≥Cinema:
≥User:
Default setting
Soft picture with fewer video artifacts
Details are sharper
Mellows movies, enhances detail in dark scenes.
You can make further adjustments.
Press [3, 4, 2, 1] to select “Detail picture
adjustment” and press [ENTER].
Contrast
Increases the contrast between light and dark parts of
the picture.
Brightness
Brightens the picture.
Sharpness
Adjust the sharpness of the edges of the horizontal
lines.
Color
Adjusts the shade of the picture’s color.
Gamma
Increases the brightness of the center ranges to improve
detail and contrast in dark scenes.
3D NR
Reduces overall noise.
Integrated DNR
Reduces mosaic noise and character smudging.
MPEG-DNR (When any item other than “User” is selected)
You can turn the recommended settings for 3D NR and
Integrated DNR on and off.
Playing back
Repeat play
Status messages
Status messages appear on the television during operation to show
the condition of the unit.
Press [STATUS].
The display changes each time you press the button.
≥Displayed information are examples.
DVD-RAM
REC
PLAY
LR
Selected drive/type of disc
Recording or play status/input
channel
Audio type
Title number and elapsed time
during recording/Recording mode Available recording time/
Recording mode
Date and time
πRemain
6/8 10:15 PM
π T2 0:05.14 XP
π T1 0:00.10 SP
0:50 XP
Play position within the title
Title number and elapsed time during play/
Recording mode
No display
Progressive§ (➡ page 48)
Select “ON” to enable progressive output.
≥Select “OFF” if the picture is stretched horizontally.
≥When progressive output is on, closed captions cannot be
displayed.
Transfer§ [When “Progressive” (➡ above) is set to “ON”.]
Select the method of conversion for progressive output to suit
the type of material being played (➡ page 48, Film and
video).
≥Auto1 (normal):
Detects 24 frame-per-second film content and
appropriately converts it.
≥Auto2: Compatible with 30 frame-per-second film content
in addition to 24 frame-per-second film content.
(Picture distortion may occur depending on the
content)
≥Video: Select when using “Auto1” and “Auto2”, and the
video content is distorted.
§
Only when you have selected “480P” in “TV Type” (➡ page 12).
RQT7303
31
7303en.book 32 ページ
2004年5月31日 月曜日 午前9時32分
Editing titles/chapters
DVD POWER
INPUT SELECT TV/VIDEO
DVD
Editing titles/chapters and playing
chapters
TV
POWER
DVD
Preparation
≥Press [DVD] to select the DVD drive.
≥Release protection (➡ page 40). [RAM]
VOLUME
CH
SD/PC
DRIVE SELECT
1
2
PAGE
1
2
3
4
5
6
7
8
CH
AUDIO
9
VCR Plus+ CM SKIP
CANCEL
0
SKIP
:9
STOP
SLOW/SEARCH
PAUSE
3
;
PLAY/x1.3
Editing
DIRECT NAVIGATOR
3421
ENTER
ENTER
SUB MENU
VIDEO PICTURE
08
10 10/27 Mon
8 10/27 Mon
--
--
--
RETURN
SUB MENU
Next
Select
To show other pages
Press [3, 4, 2, 1] to select “Previous” or “Next” and
press [ENTER].
≥You can also press [:, 9] to show other pages.
Multiple editing
Select with [3, 4, 2, 1] and press [;]. (Repeat.)
A check mark appears. Press [;] again to cancel.
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
ERASE REC MODE
--
02/02
Previous
Play
RETURN
SUB MENU
Info
Title View screen
Title View
07
FUNCTIONS
TOP MENU
SETUP
Press [3, 4, 2, 1] to select “VIDEO”
tab and press [ENTER].
Press [3, 4, 2, 1] to select the title.
DIRECT NAVIGATOR
DVD-RAM
1
DIRECT
NAVIGATOR
Press [DIRECT NAVIGATOR].
REC
CHAPTER STATUS
4
Press [SUB MENU], then [3, 4] to
select the operation and press [ENTER].
≥If you select “Edit”, press [3, 4] to select the operation and
press [ENTER].
[RAM] [DVD-R]
Enter Name
Title/Chapter
Programs are recorded as a single title consisting of one chapter.
Cancel Protection
Title
Set up Protection
Chapter
Start
End
You can divide a title into multiple chapters. [RAM]
(➡ page 26, Create chapters, ➡ page 33, Divide Chapter)
Title
Chapter
Chapter
Chapter
Erase
Shorten
Properties
Change Thumbnail
Edit
Divide Title
Chapter View
If you select “Chapter View”
5
Chapter
Press [3, 4, 2, 1] to select the
chapter.
To start play ➡ Press [ENTER].
To edit ➡ Step 6.
Chapter View screen
DIRECT NAVIGATOR Chapter View
VIDEO PICTURE
DVD-RAM
08 8 10/27 Mon
You can change the order of chapters and create a play list
(➡ page 34). [RAM]
≥Titles are divided into about 5-minute chapters after finalizing
(➡ page 41). [DVD-R]
001
---
---
---
---
---
---
---
---
---
---
---
Previous
Play
≥The maximum number of items on a disc
–Titles:
99
–Chapters:
Approximately 1000
(Depends on the state of recording.)
01/01
SUB MENU
Next
Select
≥To show other pages/Multiple editing (➡ above)
6
Press [SUB MENU], then [3, 4] to
select the operation and press [ENTER].
[Note]
Erase Chapter
≥Once erased, divided or shortened, it cannot be restored to its
original state. Make certain before proceeding.
≥You cannot edit during recording or chasing play, etc.
≥Restricted recording information remains even after editing (e.g.
dividing a title, etc).
Divide Chapter
Combine Chapters
Refer to “Chapter
operations”.
Title View
≥You can go back to the Title View.
To exit the screen
Press [DIRECT NAVIGATOR].
RQT7303
32
Refer to “Title
operations”.
To return to the previous screen
Press [RETURN].
7303en.book 33 ページ
2004年5月31日 月曜日 午前9時32分
Title operations
Erase§
[RAM] [DVD-R]
Press [2, 1] to select “Erase” and press [ENTER].
≥Once erased, the recorded contents are lost and cannot be restored. Make certain before proceeding.
≥The available recording time on DVD-R does not increase when you erase titles.
Information (e.g., time and date) is shown.
Properties
Properties
Dinosaur
No. 01
Start
10:00 AM
Date 6/20/2002 Wed Rec time 1:15 (SP)
CH 4
[RAM] [DVD-R]
Enter Name
[RAM] [DVD-R]
You can give names to recorded titles.
➡ page 37, Entering text
If set, this will protect the title from accidental erasure.
DIRECT NAVIGATOR
DVD-RAM
Press [2, 1] to select “Yes” and press [ENTER].
You can remove unnecessary parts of the recording such as commercials.
[RAM]
1 Press [ENTER] at the start point and end point of the
section you want to erase.
2 Press [3, 4] to select “Exit” and press [ENTER].
DIRECT NAVIGATOR
DVD-RAM
08
10 10/27 Mon
8 10/27 Mo
--
--
1 Press [1] (PLAY) to start play.
2 Press [ENTER] when the image you want to use as a
thumbnail is shown.
3 Press [3, 4] to select “Exit” and press [ENTER].
You can divide a title into two.
1 Press [ENTER] at the point you want to divide the title.
2 Press [3, 4] to select “Exit” and press [ENTER].
3 Press [2, 1] to select “Divide” and press [ENTER].
Shorten
VIDEO PICTURE
PLAY
Start
End
Exit
0:43.21
≥Select “Next” and press [ENTER] to erase other sections.
You can change the image to be shown as the thumbnail picture in the Title
View.
[RAM] [DVD-R]
08
Next
3 Press [2, 1] to select “Erase” and press [ENTER].
Change Thumbnail
07
The lock symbol appears when the title is protected.
[RAM]
Shorten
Title V
Editing
Set up Protection§
Cancel Protection§
Start
End
- -:- -.- -
- -:- -.- -
DIRECT NAVIGATOR Change Thumbnail
VIDEO PICTURE
DVD-RAM
08
Change
Exit
0:01.05
Change
0:01.05
DIRECT NAVIGATOR
DVD-RAM
Divide Title
VIDEO PICTURE
PLAY
08
Preview
Divide
Exit
0:43.21
Divide Title
[RAM]
To confirm the division point
Press [3, 4] to select “Preview” and press [ENTER]. (The unit plays 10
seconds before and after the division point.)
To change the division point
Restart play and press [3, 4] to select “Divide”, then press [ENTER] at the point you want to change.
Divide
-- : -- . --
[Note]
≥The divided titles retain the name and CPRM property (➡ page 48) of the original title.
≥Video and audio just before and after the dividing point may momentarily cut out.
§
Multiple editing is possible.
Chapter operations
Erase Chapter§
[RAM]
Press [2, 1] to select “Erase” and press [ENTER].
≥Once erased, the recorded contents are lost and cannot be restored. Make certain before proceeding.
1 Press [ENTER] at the point you want to divide.
≥Repeat this step to divide at other points.
Divide Chapter
2 Press [3, 4] to select “Exit” and press [ENTER].
008
PLAY
Divide
Exit
[RAM]
Combine
Chapters
DIRECT NAVIGATOR Divide Chapter
VIDEO PICTURE
DVD-RAM
0:43.21
Press [2, 1] to select “Combine” and press [ENTER].
≥The selected chapter and next chapter are combined.
[RAM]
§
Multiple editing is possible.
For quicker editing
≥Use search, Time Slip or slow-motion (➡ page 25) to find the desired point.
≥Press [:, 9] to skip to the end of a title.
RQT7303
33
7303en.book 34 ページ
2004年5月31日 月曜日 午前9時32分
Creating, editing and playing play lists
2
DVD POWER
TV
POWER
INPUT SELECT TV/VIDEO
VOLUME
CH
Press [3, 4, 2, 1] to select “PLAY
LIST” and press [ENTER].
PLAY LIST
DVD-RAM
Play List View
--
DVD
DVD
2
3
4
5
6
7
8
--
--
--
Create
PAGE
1
--
SD/PC
DRIVE SELECT
--
CH
AUDIO
9
01/01
Previous
VCR Plus+ CM SKIP
CANCEL
Next
0
SKIP
STOP
SLOW/SEARCH
PAUSE
3
PLAY/x1.3
DIRECT NAVIGATOR
FUNCTIONS
Editing
FUNCTIONS
4
TOP MENU
3421
ENTER
ENTER
SUB MENU
≥Press [ENTER] to select all the chapters in the title, then
skip to step 6.
RETURN
SUB MENU
Press [3, 4, 2, 1] to select “Create”
and press [ENTER].
Press [2, 1] to select the source title
and press [4].
RETURN
PLAY LIST
DVD-RAM
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
01
SETUP
ERASE REC MODE
Info
Create
08 8 10/27 Mon
Source Title
01/01
02
---
---
003
---
REC
Source Chapter
002
001
CHAPTER STATUS
001/001
Chapters in PLAY LIST
5
[RAM]
Press [2, 1] to select the chapter you
want to add to a play list and press
[ENTER].
Press [3] to cancel.
PLAY LIST
DVD-RAM
You can arrange the chapters (➡ page 32) to create a play list.
Title
Title
Chapter
Chapter Chapter
Play list Chapter
Chapter
Chapter
---
Source Chapter
002
001
003
---
Chapters in PLAY LIST
-----
---
---
6
You cannot create or edit a play list while recording.
Creating play lists
Preparation
≥Press [DVD] to select the DVD drive.
≥Release protection (➡ page 40). [RAM]
While stopped
DISC PROTECTION OFF
CARTRIDGE PROTECTION OFF
TIMER RECORDING
TV GUIDE
DUBBING
FLEXIBLE RECORDING
PLAY LIST
Set up
RQT7303
34
---
Source Chapter
002
001
003
---
Chapters in PLAY LIST
-----
---
---
SETUP
DISC SETTING
001/001
001/001
≥Press [3] to select other source titles.
≥Repeat steps 5–6 to add other chapters.
Press [RETURN].
To exit the screen
Press [RETURN] several times.
Play back DIRECT NAVIGATOR
Dubbing
/ Edit
01/01
---
02
Press RETURN to exit.
7
Press [FUNCTIONS].
Create
08 8 10/27 Mon
Source Title
01
Record
001/001
Press [2, 1] to select the position to
insert the chapter and press [ENTER].
PLAY LIST
DVD-RAM
[Note]
SD/PC
001/001
≥You can also create a new chapter from the source title.
Press [SUB MENU] to select “Divide Chapter” and press
[ENTER] (➡ page 33, Divide Chapter).
≥The maximum number of items on a disc
–Play lists:
99
–Chapters in play lists: Approximately 1000
(Depends on the state of recording.)
DVD-RAM
01/01
---
02
Chapter
≥Editing play lists doesn’t modify the recorded data.
≥Play lists are not recorded separately so this doesn’t use much
capacity.
DVD
Create
08 8 10/27 Mon
Source Title
01
1
001/001
EPG
To return to the previous screen
Press [RETURN].
2004年5月31日 月曜日 午前9時32分
Editing and playing play lists/chapters
1
2
3
Play list operations
Press [FUNCTIONS].
Erase§
Press [3, 4, 2, 1] to select “PLAY
LIST” and press [ENTER].
Press [3, 4, 2, 1] to select the play list.
Play list information (e.g., time and date)
is shown.
To start play ➡ Press [ENTER].
To edit ➡ Step 4.
PLAY LIST
DVD-RAM
--
10/27 Mon 0:30
Create
--
--
No.
Chapters
SUB MENU
Next
Select
Press [SUB MENU], then [3, 4] to
select the operation and press
[ENTER].
§
≥If you select “Edit”, press [3, 4] to select the operation and
press [ENTER].
Create
Copy
Enter Name
Erase
➡ page 34, Creating play lists
Copy§
Press [2, 1] to select “Copy” and
press [ENTER].
Enter Name
➡ page 37, Entering text
Change
Thumbnail
➡ page 33, Change Thumbnail
Refer to “Play list
operations”.
Multiple editing is possible.
Editing chapters in a play list does not modify the source titles and
source chapters.
Add
Chapter
Edit
Chapter View
➡ page 34, Creating play lists, Step 4–6
Press [3, 4, 2, 1] to select the
position to insert the chapter and
press [ENTER].
If you select “Chapter View”
Press [3, 4, 2, 1] to select the
chapter.
PLAY LIST
DVD-RAM
Move
Chapter
To start play ➡ Press [ENTER].
To edit ➡ Step 6.
PLAY LIST
DVD-RAM
08 10/27 Mon 0:30
---
---
---
---
---
---
---
---
---
---
Previous
SUB MENU
01/01
002
---
---
---
---
---
---
---
---
---
---
Next
Press [SUB MENU], then [3, 4] to
select the operation and press
[ENTER].
Add Chapter
§
01/01
Next
Divide
Chapter
➡ page 33, Divide Chapter
Combine
Chapters
➡ page 33, Combine Chapters
Erase
Chapter§
➡ page 33, Erase Chapter
Select
≥To show other pages/Multiple editing (➡ page 32)
6
001
Previous
002
Move Chapter
08 10/27 Mon 0:30
Chapter View
screen
Chapter View
001
Play
Date 6/20/2002 Wed
Time 0:30.05
Chapter operations
Change Thumbnail
Properties
5
01
012
Create
--
≥To show other pages/Multiple editing (➡ page 32)
4
Dinosaur
--
01/01
Previous
Play
Properties
Properties
Play List View
screen
Play List View
01
Press [2, 1] to select “Erase” and
press [ENTER].
Editing
7303en.book 35 ページ
Multiple editing is possible.
Move Chapter
Divide Chapter
Refer to “Chapter operations”.
Combine Chapters
Erase Chapter
Play List View
≥You can go back to the Play List View.
To exit the screen
Press [RETURN] several times.
To return to the previous screen
Press [RETURN].
RQT7303
35
7303en.book 36 ページ
2004年5月31日 月曜日 午前9時32分
Editing still pictures
2
DVD POWER
TV
POWER
INPUT SELECT TV/VIDEO
DVD
VOLUME
CH
DRIVE SELECT
SD/PC
DVD, SD/PC
3
PAGE
1
2
3
4
5
6
7
8
AUDIO
4
9
VCR Plus+ CM SKIP
0
SKIP
STOP
SLOW/SEARCH
PAUSE
Press [3, 4, 2, 1] to select
“PICTURE” tab and press [ENTER].
Press [3, 4, 2, 1] to select the still
picture.
≥To show other pages/Multiple editing (➡ page 32)
≥To select the still pictures in another folder (➡ page 29)
CH
CANCEL
[RAM]
PLAY/x1.3
Press [SUB MENU], then [3, 4] to
select the operation and press
[ENTER].
Erase Picture
DIRECT NAVIGATOR
Editing
DIRECT
NAVIGATOR
Set up Protection
FUNCTIONS
Cancel Protection
3,4,2,1
ENTER
ENTER
SUB MENU
RETURN
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
ERASE REC MODE
I f
REC
CHAPTER STATUS
[RAM] [SD] [PC]
Preparation
≥Press [DVD] or [SD/PC] to select the drive.
≥Release protection (➡ page 40).
1
Start Slide Show
page 29
Slide Interval
RETURN
SUB MENU
SETUP
below
DPOF
TOP MENU
Press [DIRECT NAVIGATOR].
To exit the screen
Press [DIRECT NAVIGATOR].
∫ To edit still picture folders
In step 3 (➡ above)
Erase Whole Folder
1 Press [3, 4, 2, 1] to select “Folder” and
Folder Name
press [ENTER].
Set up Protection
2 Press [3, 4] to select the folder.
Cancel Protection
≥To show other pages/Multiple editing
DPOF
(➡ page 32)
3 Press [SUB MENU], then [3, 4] to select the operation and
press [ENTER].
≥To select another higher folder (➡ page 29)
To return to the previous screen
Press [RETURN].
Picture and folder operation
Erase Picture§
Erase Whole Folder§
[RAM] [SD] [PC]
Set up Protection§
Cancel Protection§
[RAM] [SD] [PC]
§
DPOF
[SD] [PC]
Press [2, 1] to select “Erase” and press [ENTER].
≥Once erased, the recorded contents are lost and cannot be restored. Make certain before
proceeding.
≥When erasing a folder, even the files not containing still pictures will also be erased if they are inside the
folder. (This does not apply to folders under the folder concerned.)
If set, this will protect the still picture or folder from accidental erasure.
Press [2, 1] to select “Yes” and press [ENTER].
The lock symbol appears when the still picture or folder is protected.
≥Even if the protection setting is used by this unit to protect a folder, the folder
may be erased by another unit.
DIRECT NAVIGATOR
Folder
103__
0001
0002
0005
0006
You can select a whole folder or individual pictures for printing and specify the number of prints to be
made.
Press [2, 1] to select number of print (0 to 9)
and press [ENTER].
DPOF
Set up DPOF on the picture (JPEG).
The contents set with other units will be erased.
Number of prints
1
Press ENTER to confirm.
The DPOF mark appears.
≥This appears on the still pictures inside a folder when you make the DPOF setting for the folder.
SELECT
To cancel the print setting
Set the number of print to “0”.
≥When this is set by this unit, any settings established by other units will be released.
≥Print settings (DPOF) made using this unit may not be viewable on other equipment.
≥Settings cannot be made for folders and files not in accordance with DCF standards or if there is no
remaining space on the card.
Folder Name
[RAM] [SD] [PC]
§
RQT7303
36
Multiple editing is possible.
Pic
SD CARD
You can give names to still picture folders.
➡ page 37, Entering text
≥Folder names input using this unit may not be displayed on other equipment.
7303en.book 37 ページ
2004年5月31日 月曜日 午前9時32分
Entering text
1
INPUT SELECT TV/VIDEO
DVD
VOLUME
Title
Select “Enter Name” in step 4 on page 32.
SD/PC
Play list
Select “Enter Name” in step 4 on page 35.
CH
DRIVE SELECT
PAGE
Numbered
buttons
1
2
3
4
5
6
CH
8
9
Folder of still pictures
Select “Folder Name” in step 4 on page 36.
VCR Plus+ CM SKIP
CANCEL
0
SKIP
;
Disc
Select “Disc Name” in step 3 on page 40.
AUDIO
7
¢ CANCEL
Show Enter Name screen.
TV
POWER
STOP
SLOW/SEARCH
PAUSE
Name field: shows the text you have entered
PLAY/x1.3
∫
DIRECT NAVIGATOR
Enter Name
_
FUNCTIONS
1 1
2
3
5
6
7
8
2 A
B
C
a
b
c
i j ¢
3 D
4 G
E
F
d
e
f
/
l %
H
I
g
h
i
fl
$
; ERASE
5 J
K
L
j
l
O N @
π
6 M N
O
k
m n
o
[
]
_
7 P
8 T
Q
R
p
q
r
s
(
U
V
t
u
v
{
}
)
-
9 W X
0 . ,
Y
Z
w
x
?
!
"
'
y
:
z
;
\
`
|
^
TOP MENU
3,4,2,1
ENTER
ENTER
SUB MENU
RETURN
RETURN
SET
0 –– ¢
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
SETUP
Info
ERASE REC MODE
4
S
¢
REC
9
0
Editing
DVD POWER
&
SPACE
CHAPTER STATUS
2
Press [3, 4, 2, 1] to select a
character and press [ENTER].
Repeat this step to enter other characters.
≥To erase a character
Press [3, 4, 2, 1] to select the character in the name field
and press [;].
[RAM] [DVD-R] [SD] [PC]
You can give names to recorded titles, etc.
≥Using the numbered buttons to enter characters
e.g., entering the letter “R”
5 J K
1Press [7] to move to the 7th
7
7
row.
6 M N
7
2Press [7] twice to highlight
“R”.
7 P Q
3Press [ENTER].
The maximum number of characters:
[RAM]
Characters
Title
64
Play list
64
Disc
64
Folder of still pictures
36
[DVD-R]
Characters
Title
44
Disc
40
[SD] [PC]
Folder of still pictures
Characters
36
[Note]
If a name is long, parts of it may not be shown in some screens.
8 T
U
L
O
R
S
V
≥To enter a space
Press [¢ CANCEL] and press [ENTER].
3
Press [∫] (SET).
Returns to the previously displayed screen.
To end partway
Press [RETURN].
Text is not saved.
[DVD-R]
For your reference
If you enter a long name, only part of it is shown in the TOP MENU
after finalization (➡ page 41). When entering a title name, the name
that will appear in the TOP MENU can be previewed in “Display in
DVD-R TOP MENU” window.
Enter Name
Chapter 1_
Display in DVD-R
TOP MENU
Chapter 1
S
1 1
2
3
5
6
7
8
9
0
2 A
B
C
a
b
c
i j
3 D
4 G
E
F
4
d
e
f
/
l %
*
H
I
g
h
i
fl
$
&
5
RQT7303
37
7303en.book 38 ページ
2004年5月31日 月曜日 午前9時32分
Transferring (dubbing) still pictures
∫ To register on a folder by folder basis
VOLUME
CH
INPUT SELECT TV/VIDEO
1 Press [3, 4] to select “Picture/Folder” and press
[ENTER].
INPUT SELECT
DVD
DRIVE SELECT
SD/PC
PAGE
1
2
DVD, SD/PC
Dubbing
3
4
5
7
8
6
1 Dubbing direction
SD card > DVD
AUDIO
Picture High Speed
2 Press [3, 4] to select “Folder” and press [ENTER].
3 Press [3, 4] to select “New entry” and press
[ENTER].
4 Press [3, 4] to select the folder and press [ENTER].
≥To select a multiple number of items together, press [;]
to add the check mark and press [ENTER] (➡ below,
Multiple editing).
≥To show other pages (➡ below)
≥To switch another higher folder (➡ below)
≥To edit the transferring (dubbing) list (· below)
Still pictures and folders cannot be registered on the same list.
0
SKIP
:9
;
∫
SLOW/SEARCH
STOP
PAUSE
PLAY/x1.3
DIRECT NAVIGATOR
FUNCTIONS
FUNCTIONS
TOP MENU
3421
ENTER
ENTER
SUB MENU
RETURN
RETURN
SUB MENU
5
Press [3, 4] to select “SET” and
press [ENTER].
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
Transfer (Dubbing)
REC MODE
SETUP
ERASE REC MODE
Info
REC
¥ REC
CHAPTER STATUS
Press [3, 4] to select “Start
dubbing” and press [ENTER].
≥For individual still pictures only
When specifying another folder as the transferring (dubbing)
destination, select “Folder”.
1
While stopped
2
Press [FUNCTIONS].
Press [3, 4, 2, 1] to select
“DUBBING” and press [ENTER].
2 Mode
Source
SD card
Destination
DVD
Make a new folder and dub to it?
Press [2, 1] to select “Yes” and press [ENTER] to start
transferring (dubbing).
To stop transferring (dubbing)
Press and hold [RETURN] for 3 seconds.
1 Press [3, 4, 2, 1] to select “Folder” and press [ENTER].
2 Press [3, 4] to select the folder and press [ENTER].
Create list
Press [3, 4] to select “Dubbing
direction” and press [1].
1 Press [3, 4] to select “Source” and press [ENTER].
2 Press [3, 4] to select the drive and press [ENTER].
3 Press [3, 4] to select “Destination” and press
[ENTER].
4 Press [3, 4] to select the drive and press [ENTER].
The same drive as the transfer (dubbing) source can be
selected.
5 Press [2] to confirm.
Press [3, 4] to select “Create list”
and press [1].
Select the transferring (dubbing) items and register on the list.
Dubbing
Cancel all
1 Dubbing direction
SD card > DVD
Create a dubbing list.
Picture
Picture/Folder
Space on destination: 4343MB
Name
No. Capacity
New entry
2 Mode
Picture High Speed
3 Create list
Previous
Next
SET
01/01
∫ To register individual still pictures
1 Press [3, 4] to select “New entry” and press
[ENTER].
2 Press [3, 4, 2, 1] to select a still picture and press
[ENTER].
≥To select a multiple number of items together, press [;]
to add the check mark and press [ENTER] (➡ right,
Multiple editing).
≥To show other pages (➡ right)
≥To select the still pictures in another folder (➡ right)
≥To edit the transferring (dubbing) list (· right)
\DCIM
Select pictures
SD CARD
Folder
Start dubbing
100__DVD
101__DVD
102__DVD
New folder
∫ To select another folder
0
If you are not going to change the registered list press [4]
several times (➡ step 6).
4
001
002
003
-----
To return to the previous screen
Press [RETURN].
Picture High Speed
3 Create list
New folder
Set the dubbing direction.
SD card > DVD
3
\JPEG\DCIM001
Folder
1 Dubbing direction
38
6
Transferring (dubbing) using the
transferring (dubbing) list
Cancel all
RQT7303
The transferring (dubbing) list is registered.
[RAM] [SD] [PC]
Dubbing
Picture
Picture/Folder
Space on destination: 4343MB
Name
No. Capacity
New entry
2 Mode
9
VCR Plus+ CM SKIP
CANCEL
Create a dubbing list.
Cancel all
CH
0001
103__DVD
0002
0003
0004
001
002
003
004
---
\DCIM\100__DVD
100__DVD
101__DVD
102__DVD
103__DVD
≥The still pictures of different folders cannot be registered on the
same list.
≥If there is a multiple number of higher
folders recognizable, you can switch
them using [2, 1]. (Folders whose
higher folders are different cannot be
registered on the same list.)
\DCIM
001 100__DVD
002 101__DVD
003 102 DVD
∫ To edit the transferring (dubbing) list
Select the item in step 4 (➡ left)
1 Press [SUB MENU].
2 Press [3, 4] to select the operation and press
[ENTER].
§ Multiple editing is possible (➡ below).
Erase all
Add
Erase§
To cancel all registered transferring (dubbing) setting and lists
In step 3 (➡ left)
1 Press [3, 4] to select “Cancel all” and press [ENTER].
2 Press [2, 1] to select “Yes” and press [ENTER].
≥The settings and lists may be cancelled in the following situations.
–When a still picture or folder has been recorded or erased at the
transfer (dubbing) source
–When steps have been taken, for instance, to turn off the unit,
remove the card, open the tray, change the transfer (dubbing)
direction, etc.
To show other pages
Press [3, 4, 2, 1] to select “Previous” or “Next” and press
[ENTER].
≥You can also press [:, 9] to show other pages.
Multiple editing
Select with [3, 4, 2, 1] and press [;]. (Repeat.)
Press [ENTER] to register to the list.
≥A check mark appears. Press [;] again to cancel.
7303en.book 39 ページ
2004年5月31日 月曜日 午前9時32分
Recording from a video
cassette recorder
Transferring (dubbing) all the still
pictures of a card onto a DVD-RAM—
COPY ALL PICTURES
[SD] or [PC] > [RAM]
Refer to the control reference on page 38.
[RAM] [DVD-R]
Preparation
≥Connect a video cassette recorder to this unit’s input terminals.
≥Press [DVD] to select the DVD drive.
Preparation
Press [SD/PC] to select the source drive.
[Note]
1
When recording using this unit’s input terminals, only the sound
received at the time of recording will be recorded.
As long as secondary audio that is recorded on the video cassette is
not output on the unit in play, it is not recorded.
2
3
While stopped
Press [FUNCTIONS].
Press [3, 4, 2, 1] to select “COPY
ALL PICTURES” and press [ENTER].
Press [3, 4] to select “Copy from”
and press [2, 1] to select the drive.
e.g.: Connecting to the L2 input terminals
≥Turn off the unit and other video equipment before connecting.
OPEN/CLOSE
This unit
SD CARD
PC CARD
REC
EJECT
POWER
TIME SLIP
DVD
SD
PC
TIME SLIP
L2
S-VIDEO IN
VIDEO IN
L/MONO AUDIO IN
DRIVE SELECT
/x1.3
CH
R
Copy All Pictures (JPEG)
SD card
Copy to
DVD
\JPEG\DCIM001
S-VIDEO IN
Copy all pictures (JPEG) in the card
4
VIDEO IN L/MONO - AUDIO IN - R
Yellow White Red
≥If there is a multiple number of higher folders recognizable,
you can switch them using [2, 1].
Press [3, 4, 2, 1] to select “Copy”
and press [ENTER].
To stop transferring (dubbing)
Press and hold [RETURN] for 3 seconds.
Audio/Video cable
S-Video
cable§
To return to the previous screen
Press [RETURN].
Transfer (Dubbing)
Copy from
\DCIM
Other video equipment
If the audio output of the other equipment is monaural, connect to L/
MONO.
§ The S-VIDEO terminal achieves a more vivid picture than the
VIDEO terminal.
1
While stopped
Press [INPUT SELECT] to select the
input channel for the equipment you
have connected.
e.g., If you have connected to L2 input terminals, select “L2”.
[Note]
≥When transferring (dubbing) the still pictures on a folder by
folder or card by card basis, files other than the still picture files
inside the folder will also be transferred (dubbed). (This does
not apply to the lower folders contained inside the folders.)
≥If still pictures are already contained inside the transfer
(dubbing) destination folder, the new still pictures are recorded
following the existing still pictures.
≥If the space on the destination drive runs out or the number of
files/folders to be transferred (dubbed) exceeds the maximum
(➡ page 28), transferring (dubbing) will stop partway through.
≥When a name has been input by this unit for the transfer
(dubbing) source folder, the folder name will be reflected in the
transfer (dubbing) destination folder.
≥Print number setting (DPOF) is not transferred (dubbed).
≥The sequence in which the still pictures are registered on the
transfer (dubbing) list may not be reflected at the transfer
(dubbing) destination.
2
Press [REC MODE] to select the
recording mode.
3
Start play on the other equipment.
4
Press [¥ REC].
Recording starts.
To skip unwanted parts
Press [;] to pause recording. (Press again to restart recording.)
To stop recording
Press [∫].
To record programs to fill up the remaining space on the disc
➡ page 18, Flexible Recording
Almost all videos and DVD software on sale have been
treated to prevent illegal copying. Any software that has
been so treated cannot be recorded using this unit.
RQT7303
39
7303en.book 40 ページ
2004年5月31日 月曜日 午前9時32分
FUNCTIONS window
Disc and card setting
Refer to the control reference on the left.
DVD POWER
Setting the protection
TV
POWER
INPUT SELECT TV/VIDEO
DVD
DRIVE SELECT
SD/PC
PAGE
2
3
4
5
6
7
8
9
DVD, SD/PC
PROTECT
CH
[SD] [PC]
Switch the write-protect switch to
the “LOCK” position.
AUDIO
VCR Plus+ CM SKIP
CANCEL
≥For a DVD-RAM with a cartridge or for a card
[RAM]
With the write-protect tab in the protect position,
play automatically starts when inserted in the unit.
e.g. SD Memory
Card
LOCK
1
∫ Setting the protection for the whole disc or card
VOLUME
CH
0
SKIP
STOP
SLOW/SEARCH
PAUSE
≥For a DVD-RAM without a cartridge (➡ below, Disc Protection)
PLAY/x1.3
DIRECT NAVIGATOR
∫ Other protection settings
FUNCTIONS
FUNCTIONS
TOP MENU
3,4,2,1
ENTER
ENTER
SUB MENU
Title
Select “Set up Protection” in step 4 on page 32.
Still picture or folder
Select “Set up Protection” in step 4 on page 36.
RETURN
Disc Protection
RETURN
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
Convenient functions
SETUP
Info
ERASE REC MODE
REC
CHAPTER STATUS
[RAM]
Preparation
Press [DVD] to select the DVD drive.
1
2
3
By using the FUNCTIONS window you may access the main
functions quickly and easily.
1
While stopped
4
Press [FUNCTIONS].
DVD
While stopped
Press [FUNCTIONS].
Press [3, 4, 2, 1] to select “DISC
SETTING” and press [ENTER].
Press [3, 4] to select “Disc
Protection” and press [ENTER].
Press [2, 1] to select “Yes” and
press [ENTER].
DISC SETTING
DVD-RAM
SD/PC
DVD-RAM
DISC PROTECTION OFF
CARTRIDGE PROTECTION OFF
Dubbing
/ Edit
11
0 : 22
Free
Disc Protection
TIMER RECORDING
TV GUIDE
DUBBING
FLEXIBLE RECORDING
5:38 (EP)
Disc Name
Play back DIRECT NAVIGATOR
Record
Titles
Used
EPG
On
Earse all titles
Format disc
PLAY LIST
Set up
SETUP
The lock symbol appears closed when the disc is writeprotected.
DISC SETTING
Functions displayed depend on the selected drive or type of
disc.
Providing a disc with a name
[RAM] [DVD-R]
2
Press [3, 4, 2, 1] to select an item
and press [ENTER].
To exit the FUNCTIONS window
Press [FUNCTIONS].
Preparation
≥Press [DVD] to select the DVD drive.
≥Release protection (➡above).
1
2
3
While stopped
Press [FUNCTIONS].
Press [3, 4, 2, 1] to select “DISC
SETTING” and press [ENTER].
Press [3, 4] to select “Disc Name”
and press [ENTER].
➡ page 37, Entering text
≥The disc name is displayed in the FUNCTIONS window.
≥With a finalized DVD-R, the name is displayed on the Top Menu.
DVD
SD/PC
DVD-RAM
Documentary
DISC PROTECTION OFF
CARTRIDGE PROTECTION OFF
Play back DIRECT NAVIGATOR
RQT7303
40
To exit the screen
Press [RETURN] several times.
To return to the previous screen
Press [RETURN].
My favorite
01
Chapter 1
01/02
02
Chapter 2
2004年5月31日 月曜日 午前9時32分
Erasing all titles and play lists—Erase
all titles
[RAM]
Preparation
≥Press [DVD] to select the DVD drive.
≥Release protection (➡ page 40).
1
To stop formatting
Press [RETURN].
(You can cancel formatting if it takes more than 2 minutes. The disc
or card must be reformatted if you do this.)
≥Formatting cannot be performed on DVD-R or CD-R/RW.
≥When a disc or card has been formatted using this unit, it may not
be possible to use it on any other equipment.
≥You cannot format a Microdrive or mobile hard disk on this unit.
While stopped
Press [FUNCTIONS].
Press [3, 4, 2, 1] to select “DISC
SETTING” and press [ENTER].
Press [3, 4] to select “Erase all
titles” and press [ENTER].
Press [2, 1] to select “Yes” and
press [ENTER].
Press [2, 1] to select “Start” and
press [ENTER].
2
3
4
5
A message appears when finished.
6
Enabling DVD-R to be played on other
equipment—Finalize
[DVD-R]
Preparation
Press [DVD] to select the DVD drive.
1
2
3
Press [ENTER].
≥Once erased, the recorded contents are lost and cannot be
restored. Make certain before proceeding.
≥Still picture data (JPEG, TIFF) or computer data cannot be erased.
≥Erase does not work if one or more titles are protected.
[RAM] [SD] [PC]
Preparation
≥Press [DVD] or [SD/PC] to select the drive.
≥Release protection (➡ page 40).
1
2
3
4
5
While stopped
Press [FUNCTIONS].
Press [3, 4, 2, 1] to select “DISC
SETTING” or “CARD SETTING” and
press [ENTER].
Press [3, 4] to select “Format disc”
or “Format” and press [ENTER].
Press [2, 1] to select “Yes” and
press [ENTER].
Press [2, 1] to select “Start” and
press [ENTER].
Press [FUNCTIONS].
Press [3, 4, 2, 1] to select “DISC
SETTING” and press [ENTER].
Press [3, 4] to select “Select First
play” and press [ENTER].
Press [3, 4] to select “Top Menu” or “Title 1” and press
[ENTER].
You can select whether to show the top menu after finalizing.
Top Menu: The top menu appears first.
Title 1:
The disc content is played without displaying the
top menu.
[Note]
Erasing all the contents of a disc or
card—Format
While stopped
4
Press [3, 4] to select “Finalize” and
press [ENTER].
1 Press [2, 1] to select “Yes” and press [ENTER].
2 Press [2, 1] to select “Start” and press [ENTER].
A message appears when finalizing is finished.
3 Press [ENTER].
[Note]
After finalizing
≥The disc becomes play-only and you can no longer record
or edit.
≥Titles are divided into about 5-minute§ chapters.
§
This time varies greatly depending on the condition and mode
of recording.
≥There is a pause of several seconds between titles during play.
Do not disconnect the AC power supply cord while
finalizing. This will render the disc unusable.
≥Finalizing takes up to 15 minutes.
≥You cannot finalize DVD-R recorded on other manufacturer’s
equipment.
Before
finalizing
After
finalizing
DVD-R
DVD-V
Recording/Editing/Entering name
±
t
Play on other players
t
±
A message appears when formatting is finished.
6
Press [ENTER].
[Note]
≥Formatting erases all contents (including computer data),
and it cannot be restored. Check carefully before
proceeding. The contents are erased when you format it even if
you have set protection.
≥Do not disconnect the AC power supply cord while
formatting. This can render the disc unusable.
Formatting normally takes a few minutes, however it may take up
to a maximum of 70 minutes ([RAM]).
To exit the screen
Press [RETURN] several times.
Convenient functions
7303en.book 41 ページ
Disc display on this unit
DVD-R finalized on this unit may not be playable on other players
due to the condition of the recording.
≥Visit Panasonic’s homepage for more information about DVDs.
http://www.panasonic.com/playDVD-R
To return to the previous screen
Press [RETURN].
RQT7303
41
7303en.book 42 ページ
2004年5月31日 月曜日 午前9時32分
Changing the unit’s settings
Common procedures
DVD POWER
Í DVD POWER
1
TV
POWER
DVD
DRIVE SELECT
While stopped
VOLUME
CH
INPUT SELECT TV/VIDEO
Press [SETUP].
Tabs
SD/PC
Menus
Options
PAGE
Numbered
buttons
1
2
3
4
5
6
SETUP
CH
7
8
Antenna System
9
0
SKIP
STOP
2
SLOW/SEARCH
PAUSE
Press [3, 4] to select the tab and
press [1].
Press [3, 4] to select the menu and
press [ENTER].
Press [3, 4] to select the option and
press [ENTER].
PLAY/x1.3
DIRECT NAVIGATOR
3
FUNCTIONS
TOP MENU
3,4,2,1
ENTER
ENTER
SUB MENU
4
RETURN
RETURN
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
SETUP
SETUP
To exit the screen
Press [SETUP].
REC
ERASE REC MODE
Info
CATV
Auto Channel Setting
Channel Captions
Channel
Set Up
VCR Plus+ CM SKIP
CANCEL
¢ CANCEL
Convenient functions
TV GUIDE Setting
AUDIO
CHAPTER STATUS
To return to the previous screen
Press [RETURN].
Summary of settings
The settings remain intact even if you switch the unit to standby.
§1 You need to set these menus only when you do not use TV Guide On Screen TM system. These menus turn gray and become un-selectable
after this unit downloads the television program list.
§2 You can set these menus only after “Auto Channel Setting” is completed.
Tabs
Channel
Menus
TV GUIDE Setting
Set the TV Guide On ScreenTM system.
Antenna System§2
Select to suit the type of antenna you are using.
≥TV
Auto Channel Setting§1 (➡ page 45)
j
Preset Channel Captions
Set Up
Options (Underlined items are the factory presets.)
§2
(➡ page 46)
j
Manual Channel Captions§2 (➡ page 46)
j
Off Timer
Select how long the unit remains on when it is not being used.
≥2 hr
Remote Control Code (➡ page 13)
≥Set Code 1
Auto Clock Setting
§1
≥CATV
≥6 hr
≥Off
≥Set Code 2
≥Set Code 3
(➡ page 45)
Manual Clock Setting§1 (➡ page 11)
Disc
RQT7303
42
Time Zone Adjust§1 (➡ page 45)
≥j1
≥0
Re-initialize Settings
This returns all values in the SETUP menus, except for the
clock, channel settings, ratings level, and on-screen language,
to the default settings.
≥Yes
≥No
≥i1
Languages
Choose the language for audio, subtitle and disc menus. [DVD-V] ≥Enter a code (➡ page 50) with the numbered buttons when
you select “Other ¢¢¢¢”.
≥Press [ENTER] to show the following settings.
When the selected language is not available on the disc, the
≥Some discs start in a certain language despite any changes
default language is played. There are discs where you can
you make here.
only switch the language from the menu screen (➡ page 24).
Audio Language
≥French
≥Spanish
≥English
≥Original: The original language of each disc will be selected.
≥Other ¢¢¢¢
Subtitle Language
≥Automatic:
If the language selected for “Audio Language” is not available,
subtitles of that language will automatically appear if available
on that disc.
≥English
≥French
≥Spanish ≥Other ¢¢¢¢
Menu Language
≥English
Continued on next page
≥French
≥Spanish
≥Other ¢¢¢¢
2004年5月31日 月曜日 午前9時32分
Tabs
Disc
Continued
Video
Menus
Options (Underlined items are the factory presets.)
Ratings
Set a ratings level to limit DVD-Video play.
≥8 No Limit:
≥1 to 7:
Follow the on-screen instructions. Enter a 4-digit password with
the numbered buttons when the password screen is shown.
≥Do not forget your password.
≥0 Lock All:
Recording Time in EP Mode
Select the maximum number of hours for recording in EP mode
(➡ page 17, Recording modes and approximate recording times).
≥EP (6H): You can record for 6 hours on an unused 4.7 GB disc.
≥EP (8H): You can record for 8 hours on an unused 4.7 GB disc.
Play DVD-Audio in Video Mode
Select “Video (On)” to play DVD-Video content on some DVDAudio.
≥Video (On):The setting returns to “Audio (Off)” when you
change the disc or turn the unit off.
≥Audio (Off)
3-D Y/C Separation
≥On:
All DVD-Video can be played.
Prohibits play of DVD-Video with corresponding
ratings recorded on them.
Prohibits play of all DVD-Video.
≥Unlock Recorder
≥Change Level
≥Off:
≥Change Password
≥Temporary Unlock
Reduces noise by separating the luminance (Y) and
color (C) signals when recording.
Reduces the ghosting that occurs when recording fast
moving images.
Hybrid VBR Resolution
(➡ page 48, VBR)
≥Automatic: The resolution is automated to provide efficient
recording with less block noise. [RAM]
The resolution is fixed to ensure that there is no
≥Fixed:
loss of source picture resolution while recording.
Still Mode
Select the type of picture shown when you pause play
(➡ page 48, Frames and fields).
≥Automatic
≥Field: Select if jittering occurs when “Automatic” is selected.
≥Frame: Select if small text or fine patterns cannot be seen
clearly when “Automatic” is selected.
Seamless Play
Select the play mode for play list chapter segments.
≥On:
≥Off:
Line-in NR
Reduces video tape noise while transferring (dubbing).
≥When noise reduction is on, “3-D Y/C Separation” (➡ above)
does not work regardless of the setting.
The chapters in play lists are played seamlessly. This
does not work when there are several audio types
included on the play list and when using Quick View.
Additionally, the positioning of chapter segments may
change slightly.
The points where chapters in play lists change are
played accurately, but the picture may freeze for a
moment.
Convenient functions
7303en.book 43 ページ
≥Automatic: Noise reduction only works on picture input from a
video tape.
≥On:
Noise reduction works for any video input.
≥Off:
Noise reduction is off. Select when you want to
record input as is.
Black Level Control
Select normal, lighter or darker for adjusting the black level control to the desired setting for picture enhancement.
Audio
Input Level
Adjusts the black level of the input signal.
≥Lighter
≥Darker
Output Level (Composite/S Video)
Adjusts the black level of the output signal from the
VIDEO OUT and S-VIDEO OUT terminal.
≥Lighter
≥Darker
Output Level (Component)
Adjusts the black level of the output signal from the
COMPONENT VIDEO OUT (Y/PB/PR) terminals.
≥Lighter
≥Normal
≥Darker
Search Audio & PLAY k1.3
You may hear sound regardless of this setting with some discs.
≥On:
≥Off:
D. Range Compression [DVD-V] (Dolby Digital only)
Change the dynamic range for late night viewing.
≥On
Select MTS
Select the audio recording type, main or secondary (SAP) audio
when:
–Recording to a DVD-R.
–Recording sound in LPCM. (➡ page 44, Audio for XP
Recording)
≥SAP
≥Main
You cannot select this when recording from an external source
onto DVD-R. Select audio on the other equipment.
Audio is heard during first level search forward.
Audio is not heard during search. Quick View
(➡ page 25) does not work.
≥Off
Continued on next page
RQT7303
43
7303en.book 44 ページ
2004年5月31日 月曜日 午前9時32分
Changing the unit’s settings
Tabs
Audio
Continued
Menus
Digital Audio Output
Change the settings when you have connected equipment through this unit’s DIGITAL AUDIO OUT terminal (➡ page 9).
≥Press [ENTER] to show the following settings.
Signals are converted to 48 kHz or 44.1 kHz. (Choose
when the connected equipment cannot process
signals with sampling frequency of 96 kHz or 88.2
kHz.)
Signals are output as 96 kHz or 88.2 kHz. (Choose
≥Off:
when the connected equipment can process signals
with sampling frequency of 96 kHz or 88.2 kHz.)
Signals are converted to 48 kHz or 44.1 kHz despite the above
settings if the signals have a sampling frequency of over 96 kHz
or 88.2 kHz, or the disc has copy protection.
Dolby Digital Select how to output the signal, to output
“Bitstream” so the connected equipment
decodes the signal, or to decode on this
unit and output the signal as “PCM” (2
channel).
DTS
≥Bitstream: When connecting to equipment displaying the
Dolby Digital logo.
≥PCM:
When connecting to equipment not displaying the
Dolby Digital logo.
Convenient functions
Not making the proper settings may result
in noise, possibly damage your hearing
and speakers, and digital recording may
not work properly.
TV
Screen
RQT7303
44
≥On:
PCM Down Conversion
Select how to output audio with a sampling frequency of 96
kHz or 88.2 kHz.
[Note]
Display
Options (Underlined items are the factory presets.)
≥Bitstream: When connecting to equipment displaying the DTS
logo.
When connecting to equipment not displaying the
≥PCM:
DTS logo.
Audio for XP Recording
Choose the audio type when recording with XP mode.
≥Dolby Digital (➡ page 48)
≥LPCM (➡ page 48)
–The picture quality of LPCM recordings may be lower than
that of normal XP mode recordings.
–The audio recording becomes Dolby Digital even if you
selected LPCM when using a recording mode other than XP.
–When recording MTS broadcast, select the type of audio in
advance from “Select MTS” (➡ page 43).
Status Messages
Choose whether to show status messages automatically.
≥Automatic
On-screen Language
Choose the language for these menus and on-screen
messages.
≥Español ≥Français
≥English
–Only English is displayed in the TV Guide On ScreenTM
system regardless of the settings. Other languages cannot
be displayed.
Blue Background
Select “Off” if you do not want to have the unit show the blue
background when reception is weak.
≥On
Front Display
Changes the brightness of the unit’s display.
≥Bright
≥Dim
≥Automatic:
The display turns dark during play, and reappears
momentarily if a button is pressed. When the unit is turned off
all displays disappear. While using this mode the standby
power consumption can be reduced.
TV Type (➡ page 12)
≥Aspect 4:3 & 480I
≥Aspect 16:9 & 480I
4:3 TV Settings for DVD-Video
Select how DVD-Video widescreen picture is shown on a 4:3
standard aspect television.
≥Pan & Scan:
Video recorded for a widescreen is played as Pan & Scan
(unless prohibited by the producer of the disc).
≥Letterbox:
Video recorded for a widescreen is played in the letterbox style.
4:3 TV Settings for DVD-RAM
Select how DVD-RAM widescreen picture is shown on a 4:3
standard aspect television.
≥4:3:
Titles played as recorded.
≥Pan & Scan: Video recorded for a widescreen is played as Pan &
Scan.
≥Letterbox: Video recorded for a widescreen is played in the
letterbox style.
≥Off
≥Off
≥Aspect 4:3 & 480P
≥Aspect 16:9 & 480P
7303en.book 45 ページ
2004年5月31日 月曜日 午前9時32分
Channel/Clock settings when TV Guide On ScreenTM system is not used
Refer to the control reference on page 42.
Preparation:
If the television program list has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1 Press and hold [X CH] and [W CH] on the main unit for about five seconds.
The unit turns off.
2 Press [Í DVD POWER] to turn the unit on.
3 Complete the TV Guide On ScreenTM system setup (until [ENTER] is pressed after the “Watch
TV” message screen is displayed).
X CH W
OPEN/CLOSE
REC
TIME SLIP
DVD
SD
PC
TIME SLIP
DRIVE SELECT
/x1.3
CH
[Note]
You can set timer recording only manually after you set the unit with “Auto Channel Setting”.
Auto channel/clock settings
3
4
5
Press [SETUP].
Press [3, 4] to select “Channel” and
press [1].
Press [3, 4] to select “Auto Channel
Setting” and press [ENTER].
Press [2, 1] to select “Yes” and
press [ENTER].
Press [ENTER].
≥The unit configures channels according to the Antenna
System settings as follows.
Antenna system
Band
Channel
TV
CATV
Auto Clock Setting
Auto Clock Setting is complete.
Channel
Set Up
Disc
Video
Audio
4/4/2002 12:15 AM
DST............. ON
TIME ZONE.... CST
≥DST, Daylight Saving Time, shows the summertime setting.
≥TIME ZONE shows the time difference from Greenwich
meantime (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time) l GMT j6
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time)
l GMT j8
AST (Alaska Standard Time) l GMT j9
HST (Hawaii Standard Time) l GMT j10
For other areas: xx hr
≥If the Auto Clock Setting does not start automatically, select
“Auto Clock Setting” from the “Set Up” tab.
≥If the time was not set correctly, use manual clock setting
(➡ page 11) or time zone adjust.
6
Press [ENTER].
2–13
UHF
14–69
VHF
2–13
CATV LOW BAND
95–99
CATV MID/SUPER BAND
14–36
CATV HYPER BAND
37–65
66–94
100–125
ULTRA BAND
SPECIAL CATV CHANNEL
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
SETUP
VHF
1
Convenient functions
1
2
Time Zone Adjust
Adjust the time zone (j1 or i1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
1
2
3
Press [SETUP].
Press [3, 4] to select “Set Up” and
press [1].
Press [3, 4] to select “Time Zone
Adjust” and press [ENTER].
SETUP
Time Zone Adjust
j1
Channel
Set Up
Disc
Video
4
0
i1
Press [3, 4] to select “s1” or “r1”
and press [ENTER].
To exit the screen
Press [SETUP].
To return to the previous screen
Press [RETURN].
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
RQT7303
45
7303en.book 46 ページ
2004年5月31日 月曜日 午前9時32分
Channel/Clock settings when TV Guide On ScreenTM system is not used
Refer to the control reference on page 42.
Channel captions
You can use the preset captions, or manually enter new ones yourself.
The captions you enter are displayed when the channel is displayed and in the Direct Navigator screen.
≥You can set channel captions only after “Auto Channel Setting” is completed.
1
Press [SETUP].
SETUP
TV GUIDE Setting
Antenna System
Channel
Set Up
Disc
Video
Audio
Display
TV Screen
2
CATV
Auto Channel Setting
Channel Captions
Preset Channel Captions
Manual Channel Captions
Press [3, 4] to select “Channel” and press [1].
Convenient functions
Preset Channel Captions
3
Press [3, 4] to select “Preset
Channel Captions” and press
[ENTER].
SETUP
Channel
Set Up
Disc
Video
Audio
Display
TV Screen
4
Manual Channel Captions
Preset Captions
Caption
Channel Number
GLOB
---
ABC
---
PBS
CBS
-----
3
Press [3, 4] to select “Manual
Channel Captions” and press
[ENTER].
4
Press [3, 4] to select the channel
and press [1].
≥Channels are only displayed if they contain a station and if
preset captions have not been added.
5
≥You can choose from the following characters:
A–Z, 0–9, -, &, !, /, (space)
≥To delete the caption, press [¢ CANCEL].
≥Repeat this step to enter the other characters.
Press [3, 4] to select the caption and
press [1].
You can choose from the following captions.
ABC, PBS, CBS, CNN, FOX, ESPN, NBC, HBO, A&E, AMC,
FAM, MAX, MTV, SHOW, TBS, USA, TNT, CBC, UPN, CTV,
WB, TSN, DSC, GLOB
≥When selecting the caption, press and hold [3, 4] to scroll
up and down the screen.
5
Press [3, 4] to select the channel
corresponding to the caption and
press [2].
≥Channels are only displayed if they contain a station and if
captions have not been added manually.
≥To delete the channel number, press [¢ CANCEL].
SETUP
Press [ENTER].
To exit the screen
Press [SETUP].
To return to the previous screen
Press [RETURN].
RQT7303
46
Manual Captions
Channel Number
Caption
6
8
-------
10
AAAA
12
23
-------
Channel
Set Up
Disc
Video
Audio
Display
TV Screen
6
Press [2, 1] to return to the “Channel
Number” column.
Repeat steps 4–6 to enter other channels.
Repeat steps 4 and 5 to enter other channels.
6
Press [3, 4] to select the first
character and press [1].
7
Press [ENTER].
7303en.book 47 ページ
2004年5月31日 月曜日 午前9時32分
Specifications
DVD Video Recording format (DVD-RAM)
DVD-Video format (DVD-R)
Recordable discs:
DVD-RAM :
12 cm (5q) 4.7 GB, 12 cm (5q) 9.4 GB, 8 cm (3q) 2.8 GB
12 cm (5q) 4.7 GB (Ver. 2.1/3k–SPEED DVD-RAM Revision 1.0)
DVD-R :
12 cm (5q) 4.7 GB, 8cm (3q) 1.4 GB (for General Ver. 2.0)
12 cm (5z) 4.7 GB (for General Ver. 2.0/4k–SPEED DVD-R
Revision 1.0)
Recording time:
≥Maximum 8 hours (with 4.7 GB disc)
XP: Approx. 1 hour
SP: Approx. 2 hours
LP: Approx. 4 hours EP: Approx. 6 hours/8 hours
Playable discs:
DVD-RAM :
12 cm (5q) 4.7 GB, 12 cm (5q) 9.4 GB, 8 cm (3q) 2.8 GB
12 cm (5q) 4.7 GB (Ver. 2.1/3k–SPEED DVD-RAM Revision 1.0)
DVD-R :
12 cm (5q) 4.7 GB, 8cm (3q) 1.4 GB (for General Ver. 2.0)
12 cm (5z) 4.7 GB (for General Ver. 2.0/4k–SPEED DVD-R
Revision 1.0)
DVD-Video, DVD-Audio, Video CD, CD-Audio (CD-DA)
CD-R/CD-RW (MP3, CD-DA, Video CD formatted discs)
Drive unit:
High Speed Drive (correspond to 4 times speed with
DVD-R disc and 3 times speed with DVD-RAM disc)
LASER Specification
Class I LASER Product
Wave length:
795 nm wavelength (for CDs), 658 nm wavelength (for DVDs)
Laser power:
No hazardous radiation is emitted with the safety protection
Audio system
Recording system:
Dolby Digital 2 ch, Linear PCM (XP mode, 2ch)
Input:
LINE (pin jack)a3
Reference input: 309 mVrms, FS: 2 Vrms (1 kHz, 0 dB)
Input Impedance: 47 k≠
Output:
LINE (pin jack)a2
(Load impedance: 10 k≠)
Reference output: 309 mVrms, FS: 2 Vrms (1 kHz, 0 dB)
Output Impedance: 1 k≠
Digital Audio Out:
Optical terminal (PCM, Dolby Digital, DTS)
Television system
Tuner system:
Antenna reception input:
NTSC-M
TV Channel:
2 ch–69 ch, 75 ≠
CATV Channel: 1 ch–125 ch, 75 ≠
Video system
TV system:
NTSC color signal, 525 lines, 60 fields
Recording system:
MPEG2 (Hybrid VBR)
Input:
LINE (pin jack)a3,
1.0 Vp-p; 75 ≠
S connectora3
Y: 1.0 Vp-p; C: 0.286 Vp-p; 75 ≠
Output:
LINE (pin jack)a2,
1.0 Vp-p; 75 ≠
S connectora2
Y: 1.0 Vp-p; C: 0.286 Vp-p; 75 ≠
Component video output (480P/480I):
Y: 1.0 Vp-p; 75 ≠
PB: 0.7 Vp-p; 75 ≠
PR: 0.7 Vp-p; 75 ≠
Card unit:
Still picture (JPEG, TIFF)
Card slot:
SD Memory Card/PC Card Type II
Compatible media:
SD Memory Card, MultiMediaCard,
A PC Card adaptor conforming to PC Card Standards,
ATA Flash PC Card,
PC Card adaptor (SD Memory Card, MultiMediaCard,
CompactFlash, SmartMedia, MEMORYSTICK, xD-Picture Card,
Microdrive), Mobile hard disk
Format:
FAT12, FAT16
Image format:
JPEG
DCF (Design rule for Camera File system),
(sub sampling 4:2:2 or 4:2:0),
TIFF (uncompressed RGB chunky),
DPOF Compatible
Number of pixels:
34a34 to 6144a4096
Thawing time:
Approx. 7 sec. (2 M pixels)
Others
Regional code:
‚1
Clock unit:
Quartz-controlled 12-hour digital display
Operating temperature:
5 oC–40 oC (41 oF–104 oF)
Operating humidity range: 10 %–80 % RH (no condensation)
Power supply:
AC 120 V, 60 Hz
Power consumption:
28 W
Dimensions (WkHkD):
Approx. 430 mmk79 mmk274 mm
(Approx.1615/16qk31/8qk1013/16q)
Mass:
Approx. 3.4 kg (7.5 lbs)
Power consumption in standby mode:
Reference
Recording system:
approx. 15 W
[Note]
Specifications are subject to change without notice.
Mass and dimensions are approximate.
User memo:
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
MODEL NUMBER
DMR-E65
DATE OF PURCHASE _______________________________
DEALER NAME ____________________________________
DEALER ADDRESS _________________________________
__________________________________________________
TELEPHONE NUMBER ______________________________
SERIAL NUMBER
RQT7303
47
7303en.book 48 ページ
2004年5月31日 月曜日 午前9時32分
Glossary
Bitstream
This is the digital form of multi-channel audio data (e.g., 5.1 channel)
before it is decoded into its various channels.
CPRM (Content Protection for Recordable Media)
CPRM is technology used to protect broadcasts that are allowed to
be recorded only once. Such broadcasts can be recorded only with
CPRM compatible recorders and discs.
Dolby Digital
This is a method of coding digital signals developed by Dolby
Laboratories. Apart from stereo (2-channel) audio, these signals can
also be multi-channel audio. A large amount of audio information can
be recorded on one disc using this method.
When recording on this unit Dolby Digital (2 channel) is the default
audio.
Down-mixing
This is the process of remixing the multi-channel audio found on
some discs into two channels. It is useful when you want to listen to
the 5.1-channel audio recorded on DVDs through your television’s
speakers. Some discs prohibit down-mixing and this unit can then
only output the front two channels.
DPOF (Digital Print Order Format)
DPOF is the standard printing format for still picture data taken by a
digital camera, etc. It is used for automatic printing at a photo
developing store or on your home printer.
Reference
Drive
In the instance of this unit, this refers to the disc (DVD), SD card
(SD) and PC card (PC). These perform the reading and writing of
data.
DTS (Digital Theater Systems)
This surround system is used in many movie theaters. There is good
separation between the channels, so realistic sound effects are
possible.
Dynamic range
Dynamic range is the difference between the lowest level of sound
that can be heard above the noise of the equipment and the highest
level of sound before distortion occurs.
Dynamic range compression means reducing the gap between the
loudest and softest sounds. This means you can listen at low
volumes but still hear dialog clearly.
Film and video
DVD-Video are recorded using either film or video. This unit can
determine which type has been used, then uses the most suitable
method of progressive output.
Film is 24 or 30 frames per second, with motion picture film generally
being 24 frames per second.
Video is 60 fields per second (two fields making up one frame).
Finalize
A process that makes play of a recorded CD-R, CD-RW, DVD-R, etc.
possible on equipment that can play such media. You can finalize
DVD-R on this unit.
After finalizing, the disc becomes play-only and you can no longer
record or edit.
Folder
This is a place on the disc or memory card where groups of data are
stored together. In the case of this unit, it refers to the place where
still pictures (JPEG, TIFF) are stored.
Formatting
Formatting is the process of making media such as DVD-RAM
recordable on recording equipment.
You can format DVD-RAM and memory cards on this unit.
Formatting irrevocably erases all contents.
Frames and fields
Frames refer to the single images that constitute the video you see
on your television. Each frame consists of two fields.
u
RQT7303
48
r
Frame
Field
Field
≥A frame still shows two fields, so there may be some blurring, but
picture quality is generally better.
≥A field still shows less picture information so it may be rougher, but
there is no blurring.
JPEG (Joint Photographic Experts Group)
This is a system used for compressing/decoding color still pictures. If
you select JPEG as the storage system on digital cameras etc., the
data will be compressed to 1/10–1/100 of its original size. The
feature of JPEG is less deterioration in picture quality considering
the degree of compression.
LPCM (Linear PCM)
These are uncompressed digital signals, similar to those found on
CDs. LPCM sound is available when recording in XP mode.
MP3 (MPEG Audio Layer 3)
An audio compression method that compresses audio to
approximately one tenth of its size without any considerable loss of
audio quality. You can play MP3 you have recorded onto CD-R and
CD-RW.
Pan&Scan/Letterbox
In general, DVD-Video are produced with the intention that they be
viewed on a widescreen television (16:9 aspect ratio), so images
often don’t fit regular (4:3 aspect ratio) televisions. Two styles of
picture, “Pan & Scan” and “Letterbox”, deal with this problem.
Pan&Scan: The sides are cut off so the picture fills
the screen.
Letterbox: Black bands appear at the top and
bottom of the picture so the picture itself
appears in an aspect ratio of 16:9.
Playback control (PBC)
If a Video CD has playback control, you can select scenes and
information with menus.
(This unit is compatible with version 2.0 and 1.1.)
Progressive/Interlace
NTSC, the video signal standard, has 480 interlaced (I) scan lines,
whereas progressive scanning uses twice the number of scan lines.
This is called 480P.
Using progressive output, you can enjoy the high-resolution video
recorded on media such as DVD-Video.
Your television must be compatible to enjoy progressive video.
Protection
You can prevent accidental erasure by setting writing protection or
erasure protection.
Sampling frequency
Sampling is the process of converting the heights of sound wave
(analog signal) samples taken at set periods into digits (digital
encoding). Sampling frequency is the number of samples taken per
second, so larger numbers mean more faithful reproduction of the
original sound.
Thumbnail
This refers to a miniature representation of a picture used to display
multiple pictures in the form of a list.
TIFF (Tag Image File Format)
This is a system used for compressing/decoding color still pictures.
A common format for storing high quality images on digital cameras
and other devices.
VBR (Variable bitrate)
This is a method of video recording that adjusts the bit rate
according to video signal.
7303en.book 49 ページ
2004年5月31日 月曜日 午前9時32分
Frequently asked questions
Set up
What equipment is necessary to play multi
channel surround sound?
Page
≥ DVD-Video:
You can play DVD-Video multi channel surround by digitally connecting an
amplifier equipped with a Dolby Digital and a DTS decoder.
≥DVD-Audio:
This unit plays DVD-Audio in 2 channels. You cannot play multi channel
surround sound.
9
—
Are the headphones and speakers directly
connected to the unit?
≥You cannot directly connect to the unit. Connect through the amplifier, etc.
9
The television has both S-VIDEO IN terminal and
COMPONENT VIDEO IN terminals. Which
terminal should I connect with?
≥We recommend the COMPONENT VIDEO IN terminal. Component signal
outputs the color difference signals (PB/PR) and luminance signal (Y)
separately in order to achieve high fidelity in reproducing colors.
If the television is compatible with progressive output, a high quality picture
can be output because this unit’s component video output terminal outputs
a progressive output signal.
7
Is my television progressive output compatible?
≥All Panasonic televisions that have 480P input terminals are compatible.
Consult the manufacturer if you have another brand of television.
—
Disc
Can I play DVD-Video, DVD-Audio and Video
CDs bought in another country?
≥You can play them if the video standard is NTSC.
≥However, you cannot play DVD-Video if their region number does not
include “1” or “ALL”.
Can a DVD-Video that does not have a region
number be played?
≥The DVD-Video region number indicates the disc conforms to a standard.
You cannot play discs that do not have a region number.
—
Please tell me about DVD-R and DVD-RW
compatibility with this unit.
≥This unit records and plays DVD-R. However, you cannot record onto DVDR discs that are finalized.
≥This unit also records and plays high speed recording compatible discs.
≥This unit does not record or play DVD-RW.
—
≥This unit plays CD-R/CD-RW discs (audio recording discs) which have been
recorded under one of the following standards: CD-DA, MP3 and Video CD.
Close the session or finalize the disc after recording.
≥You cannot write to a CD-R or CD-RW with this unit.
14, 27
—
—
Reference
Please tell me about CD-R and CD-RW
compatibility with this unit.
—
Cover
—
Recording
Can I record from a commercially purchased
video cassette or DVD?
≥Most commercially sold video cassettes and DVD are copy protected;
therefore, recording is usually not possible.
—
Can a DVD-R recorded on this unit be played on
other equipment?
≥You can play on DVD-R compatible players after finalizing the disc on this
unit; however, due to the condition of the recording, play may not be
possible.
41
How many times can I write to a DVD-RAM disc?
≥You can write to the disc approximately 100,000 times depending upon the
conditions of use.
—
Can I record digital audio signals using this unit?
≥You cannot record digital signals. The digital audio terminals on this unit are
for output only.
—
Can a digital audio signal from this unit be
recorded to other equipment?
≥You can record if using the PCM signal. When recording DVD, change the
“Digital Audio Output” settings to the following from the SETUP menu.
–PCM Down Conversion
On
–Dolby Digital
PCM
–DTS
PCM
However, only
–As long as digital recording from the disc is permitted.
–As long as the recording equipment is compatible with a sampling
frequency of 48 kHz.
≥You cannot record MP3 signals.
44
≥With DVD-RAM, you can, and the audio recorded also changes. Just press
[AUDIO].
≥With DVD-R, you cannot. Change before recording with “Select MTS” in the
SETUP menu.
17
I do not want TV Guide On ScreenTM system to
automatically appear on screen.
≥Select “Off” in “Review options” menu, so that TV Guide On ScreenTM
system appears only when you press [TV GUIDE].
23
I do not want to use TV Guide On ScreenTM
system.
≥Set the unit with “Auto Channel Setting”. Note that you can set timer
recording only manually after you set the unit with “Auto Channel Setting”.
45
Can I switch to SAP during recording?
—
43
TV Guide On ScreenTM system
RQT7303
49
7303en.book 50 ページ
2004年5月31日 月曜日 午前9時32分
Error messages
On the television
Cannot finish recording
completely.
Cannot play.
Cannot record on the disc.
Please check the disc.
Unable to format.
Cannot play back on this DVDRecorder.
Cannot record. Disc is full.
Cannot record. Maximum
number of titles exceeded.
Error has occurred. Please
press ENTER.
No disc
No folders.
No PC CARD
No SD CARD
No valid PC card.
No valid SD card.
Not enough space on dubbing
destination.
Please change the disc.
This is a non-recordable disc.
This disc is not formatted
properly.
Reference
$
28
28
26, 33, 41
≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering
(“SELF CHECK” appears on the unit’s display).
≥The disc may be upside down.
≥There is no compatible folder in this unit.
≥The card is not inserted. If this message is displayed with a compatible card already
inserted, turn off the unit, remove and then re-insert the card.
≥The card inserted is not compatible or the card format does not match.
—
≥Create space by erasing any unnecessary items.
≥There may be a problem with the disc. Press [< OPEN/CLOSE] on the main unit to
remove it and check it for scratches or dirt. (The unit turns off automatically after you open
the tray.)
≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R.
≥You inserted an unformatted DVD-RAM. Format the disc with this unit.
—
—
15
28
15
26, 29, 33,
36, 41
54
—
41
—
CHK REMOTE 
(“∑” stands for a number.)
≥The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [ENTER] and the indicated number button at
the same time for more than 2 seconds.
13
HARD ERR
≥If there is no change after turning the unit on and off, consult the dealer where the unit was
purchased.
≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥You have used a DVD-RAM/PD lens cleaner and it has finished. Press [< OPEN/CLOSE]
on the main unit to eject the disc.
≥Displayed when the unit is started. This is not a malfunction.
≥There was a power failure or the AC plug was disconnected while the unit was on. The unit
is carrying out its recovery process. Wait until the message disappears.
≥You have inserted a disc the unit cannot play or record on.
≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to
standby. Now press [POWER Í/I] on the main unit again to turn the unit on.
—
On the unit’s display
PLEASE WAIT
SELF CHECK
UNSUPPORT
U14
U99
Language code list
50
≥You tried to play a non-compatible image.
≥Turn the unit off and re-insert the card.
≥Create space by erasing any unnecessary titles. [RAM]
(Even if you erase recorded content from the DVD-R, there is no increase in disc space.)
≥Use a new disc.
≥The operation is prohibited by the unit or disc.
NO READ
RQT7303
Page
—
—
—
54
—
≥The program was copy-protected.
≥The disc may be full.
≥You inserted an incompatible disc (Discs recorded in PAL video, etc.).
≥The disc may be dirty or scratched.
≥You cannot format a Microdrive or mobile hard disk on this unit.
Abkhazian:
6566
Afar:
6565
Afrikaans:
6570
Albanian:
8381
Ameharic:
6577
Arabic:
6582
Armenian:
7289
Assamese:
6583
Aymara:
6588
Azerbaijani:
6590
Bashkir:
6665
Basque:
6985
Bengali; Bangla:
6678
Bhutani:
6890
Bihari:
6672
Breton:
6682
Bulgarian:
6671
Burmese:
7789
Byelorussian: 6669
Cambodian:
7577
54
—
—
—
14
—
—
Enter the code with the numbered buttons.
Catalan:
Chinese:
Corsican:
Croatian:
Czech:
Danish:
Dutch:
English:
Esperanto:
Estonian:
Faroese:
Fiji:
Finnish:
French:
Frisian:
Galician:
Georgian:
German:
Greek:
Greenlandic:
Guarani:
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
Gujarati:
7185
Hausa:
7265
Hebrew:
7387
Hindi:
7273
Hungarian:
7285
Icelandic:
7383
Indonesian:
7378
Interlingua:
7365
Irish:
7165
Italian:
7384
Japanese:
7465
Javanese:
7487
Kannada:
7578
Kashmiri:
7583
Kazakh:
7575
Kirghiz:
7589
Korean:
7579
Kurdish:
7585
Laotian:
7679
Latin:
7665
Latvian, Lettish:7686
Lingala:
7678
Lithuanian:
7684
Macedonian: 7775
Malagasy:
7771
Malay:
7783
Malayalam:
7776
Maltese:
7784
Maori:
7773
Marathi:
7782
Moldavian:
7779
Mongolian:
7778
Nauru:
7865
Nepali:
7869
Norwegian:
7879
Oriya:
7982
Pashto, Pushto:8083
Persian:
7065
Polish:
8076
Portuguese:
8084
Punjabi:
8065
Quechua:
8185
Rhaeto-Romance:
8277
Romanian:
8279
Russian:
8285
Samoan:
8377
Sanskrit:
8365
Scots Gaelic: 7168
Serbian:
8382
Serbo-Croatian:8372
Shona:
8378
Sindhi:
8368
Singhalese:
8373
Slovak:
8375
Slovenian:
8376
Somali:
8379
Spanish:
6983
Sundanese:
8385
Swahili:
8387
Swedish:
8386
Tagalog:
8476
Tajik:
8471
Tamil:
Tatar:
Telugu:
Thai:
Tibetan:
Tigrinya:
Tonga:
Turkish:
Turkmen:
Twi:
Ukrainian:
Urdu:
Uzbek:
Vietnamese:
Volapük:
Welsh:
Wolof:
Xhosa:
Yiddish:
Yoruba:
Zulu:
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
7303en.book 51 ページ
2004年5月31日 月曜日 午前9時32分
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart
do not solve the problem, refer to the “Customer Services Directory” on page 55.
The following do not indicate a problem with this unit:
≥Regular disc rotating sounds. The sound of the disc rotating may
become louder especially when finalizing a DVD-R.
≥Poor reception due to atmospheric conditions.
≥Image disturbance during search.
≥Interruptions in reception due to periodic satellite broadcasting
breaks.
Power
Page
No power.
≥Insert the AC power supply cord securely into a known active AC outlet.
7
The unit switches to standby
mode.
≥This is a power saving feature. Change “Off Timer” in the SETUP menu, if you would prefer.
≥One of the unit’s safety devices is activated. Press [POWER Í/I] on the main unit to turn the
unit on.
≥If the unit is not placed in the timer recording standby mode two minutes before the time
when the timer recording is scheduled to commence, it turns off automatically and will be
placed in the standby mode. (The “F” appears on the display.) If play or recording is being
performed, it will be interrupted.
42
—
The display is dim.
≥Change “Front Display” in the SETUP menu.
44
“12:00” is flashing on the unit’s
display.
≥Set the clock.
11
Compared to the actual
recorded time, the remaining
time displayed is less.
≥The displayed recording/play time is converted from the number of frames at 29.97 frames
(equal to 0.999 seconds) to one second. There will be a slight difference between the time
displayed and the actual elapsed time (e.g., actual one-hour elapsed time may display as
approximately 59 minutes 56 seconds). This does not affect the recording.
—
The time recorded on the disc
and the available time shown
do not add up.
The play time shown for MP3
does not agree with the actual
time.
≥Times shown may disagree with actual times.
≥More disc space than the actual recording time is used after recording or editing the DVD-R
200 times or more.
≥While searching, the elapsed time may not display correctly.
≥Even if you erase recorded content from the DVD-R, there is no increase in disc space.
—
—
Television reception worsens
after connecting the unit.
≥This can occur because the signals are being divided between the unit and other equipment.
It can be solved by using a signal booster, available from audio-visual suppliers.
—
Status messages do not
appear.
≥Select “Automatic” in “Status Messages” in the SETUP menu.
44
The blue background does not
appear.
≥Select “On” in “Blue Background” in the SETUP menu.
44
The 4:3 aspect ratio picture
expands left and right.
31
Screen size is wrong.
≥Use the television to change the aspect. If your television does not have that function, set
“Progressive” in the Video menu to “OFF”.
≥Check the settings for “TV Type”, “4:3 TV Settings for DVD-Video” or “4:3 TV Settings for
DVD-RAM” in the SETUP menu.
There is a lot of after-image
when playing video.
≥Change the settings for “3D NR” and “Integrated DNR” to “0” or turn “MPEG-DNR” off if it is
on.
31
When playing DVD-Video using
progressive output, one part of
the picture momentarily
appears to be doubled up.
≥Set “Progressive” in the Video menu to “OFF”. This problem is caused by the editing method
or material used on DVD-Video, but should be corrected if you use interlace output.
31
There is no apparent change in
picture quality when adjusted
with the Video menu in the onscreen menus.
≥The effect is less perceivable with some types of video.
—
The images from this unit do
not appear on the television.
≥Make sure that the television is connected to the VIDEO OUT terminal, S-VIDEO OUT
terminal or COMPONENT VIDEO OUT terminals on this unit.
≥Make sure that the television’s input setting (e.g., VIDEO 1) is correct.
≥The television isn’t compatible with progressive signals. Press and hold [∫] and [TIME SLIP]
on the main unit at the same time for about 5 seconds. The setting will change to interlace.
7
—
—
—
Reference
Displays
TV screen and video
Picture is distorted.
44
—
—
RQT7303
51
7303en.book 52 ページ
2004年5月31日 月曜日 午前9時32分
Troubleshooting guide
Sound
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.
Cannot switch audio.
Page
≥Check the connections and settings. Check the input mode on the amplifier if you have
connected one.
≥Press [AUDIO] to select the audio.
≥Turn off V.S.S. in the following cases.
–When using discs that do not have surround sound effects such as Karaoke discs.
–When playing MTS broadcast programs.
≥The disc may have a restriction on the method of audio output. If “D.MIX” does not appear in
the display when playing multi-channel DVD-Audio, only audio for the two front channels will
be output. Refer to the disc’s jacket. [DVD-A]
≥You cannot switch the audio in the following cases.
–When a DVD-R disc is in the disc tray while DVD drive is selected.
–When the recording mode is XP and “Audio for XP Recording” is set to “LPCM”.
≥You have used digital connection. Set “Dolby Digital” to “PCM” or connect using audio cables
(analog connection).
≥There are discs for which audio cannot be changed because of how the disc was created.
7–9, 44
17, 26
31
—
—
44
44, 9
—
Operation
Reference
Cannot operate the television.
The remote control doesn’t
work.
≥Change manufacturer code. Some televisions cannot be operated even if you change the
code.
≥The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [ENTER] and the indicated number button at
the same time for more than 2 seconds.
12
≥The batteries are depleted. Replace them with new ones.
≥Colored glass may obstruct the signal reception/transmission.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
4
—
—
13
The unit is on but cannot be
operated.
≥Recording drive or playback drive has not been selected properly.
≥Some operations may be prohibited by the disc.
≥The unit is hot (“U14” appears on the display). Wait for “U14” to disappear.
≥One of the unit’s safety devices may have been activated.
Reset the unit as follows:
Press [POWER Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [POWER Í/I] on the main unit for about
10 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.
Cannot eject disc.
≥The unit may have a problem. While the unit is off, press and hold [∫] and [CH W] on the
main unit at the same time for about 5 seconds. Remove the disc and consult the dealer.
—
≥You haven’t inserted a disc or the disc you inserted cannot be recorded on. Insert a disc the
unit can record onto.
≥The disc is unformatted. Format the disc. [RAM]
≥The write-protect tab on the cartridge is set to PROTECT, or the disc is protected with DISC
SETTING.
≥Some programs have limitations on the number of times they can be recorded. (CPRM)
≥The disc is full or nearly full. Erase un-needed titles or use another disc.
14
16, 24
—
—
—
Recording and timer recording
Cannot record.
≥You cannot record on finalized DVD-R discs.
≥Due to peculiarities of DVD-R, you may be unable to record onto them if you either insert and
remove the disc or switch the unit on and off while a disc is loaded, a total of fifty times.
≥A DVD-R recorded on this unit may not be recordable on other Panasonic DVD recorders.
Timer recording does not work
properly.
VCR Plusr system does not
work properly.
RQT7303
52
≥You haven’t inserted a disc or the disc you inserted cannot be recorded on. Insert a disc the
unit can record onto.
≥The timer program is incorrect or different timer program times overlap. Correct the program.
≥Timer recording program may be deleted if there is an interruption to the power.
≥VCR Plusr system works only after this unit downloads the television program list.
41
40
48
26, 33,
41
—
—
—
14
22
—
—
Timer recording does not stop
even when [∫] is pressed.
≥Press [∫] and then [ENTER] within 5 seconds. Recording stops.
19, 20,
21
The timer program remains
even after recording finishes.
≥The timer program remains unless set to “Once”.
19, 20
A part or whole of a recorded
title has been lost.
≥If there is a power failure or the plug is disconnected from the household AC outlet while
recording or editing, the title may be lost or the disc may become unusable.
You will have to format the disc ([RAM]) or use a new disc. We cannot offer any guarantee
regarding lost titles or discs.
41
7303en.book 53 ページ
2004年5月31日 月曜日 午前9時32分
TV Guide On ScreenTM system
Page
Television program list does
not display when [TV GUIDE] is
pressed.
≥Leave the unit turned off over night.
≥Check the connection and set up the TV Guide On ScreenTM system again.
≥Consult your service provider if you are using a cable TV box.
≥Television program list is not available in your area. Set the unit using “Auto Channel Setting”.
Note that you can only set timer recording manually after you set the unit using “Auto
Channel Setting”.
—
7, 8, 10
—
45
“Cable code -INCOMPLETE-”
appears in the TV Guide On
ScreenTM system setup.
≥The unit cannot find the correct IR code for the cable TV box. Consult your service provider.
—
As soon as the unit is turned
on, and when you try to start
timer recording, the TV Guide
On ScreenTM system setup
begins.
≥Even if you do not want to use the TV Guide On ScreenTM system, you need to complete the
TV Guide On ScreenTM system setup (until [ENTER] is pressed after the “Watch TV”
message screen is displayed). It will not be displayed after this point.
10
Several days of television
program listings are blank.
≥Immediately after beginning use there are several days of blank listings. You can display
program listings up to 8 days forward without any blank listings by downloading program lists
continuously over several days.
—
Channel changes even when
no operation is performed.
≥When the unit is connected to a cable TV box, the cable TV box channel changes while the
unit is turned off in order to download the television program list.
—
Play fails to start even when
[1] (PLAY) is pressed.
Play starts but then stops
immediately.
≥Insert the disc correctly with the label facing up.
≥You tried to play a blank DVD-RAM/DVD-R, or disc unplayable on this unit.
≥When recording to DVD-RAM using EP (8H) mode, play may not be possible on DVD players
that are compatible with DVD-RAM. In this case use EP (6H) mode.
24
14
43
Audio and video momentarily
pause.
≥This occurs between play list chapters. [RAM]
—
DVD-Video is not played.
≥Some DVD-Video cannot be played when you change the ratings level.
43
Alternative soundtrack and
subtitles cannot be selected.
≥The languages are not recorded on the disc.
≥You may have to use the disc’s menus to select languages.
—
—
No subtitles.
≥When progressive output is on, closed captions cannot be displayed.
≥Subtitles are not recorded on the disc.
≥Turn the subtitles on.
—
—
30
Angle cannot be changed.
≥Angles can only be changed during scenes where different angles are recorded.
—
You have forgotten your ratings
password.
≥While the disc tray is open, press [DVD] then press and hold [D] and [E] on
the main unit at the same time for 5 or more seconds.
—
Quick View does not work.
≥This does not work if the setting is “Off” in “Search Audio & PLAY k1.3”.
≥This does not work when audio is other than Dolby Digital.
≥This does not work when recording is in XP or FR mode. [RAM]
43
—
—
The resume play function does
not work.
≥This function only works when “PLAY” is flashing on the unit display.
≥Memorized positions are canceled when the unit is turned off or when the tray is opened. The
memorized position on the play list is also canceled when the play list and title are edited.
—
—
Cannot format.
≥The disc is dirty. Use a special cleaner and wipe clean.
≥You tried formatting a disc that is not compatible with this unit.
54
14
Cannot create chapters.
—
Cannot mark the start point or
the end point during “Shorten”
operation.
≥The unit writes the chapter division information to the disc when you turn it off or remove the
disc. The information is not written if there is an interruption to the power before this.
≥These operations are not possible with still pictures.
≥You cannot set points if they are too close to each other. You cannot set an end point before a
start point.
Cannot erase chapters.
≥When the chapter is too short to erase, use “Combine Chapters” to make the chapter longer.
33
The available recording time
doesn’t increase even after
erasing recordings on the disc.
≥Available recording space on the DVD-R does not increase even after erasing previously
recorded titles.
—
Cannot create a play list.
≥You cannot select all the chapters at once in a title if the title also includes still pictures. Select
them individually.
—
Reference
Play
Edit
—
—
RQT7303
53
7303en.book 54 ページ
2004年5月31日 月曜日 午前9時32分
Troubleshooting guide
Still pictures
Page
Cannot display Direct
Navigator screen.
≥This screen cannot be displayed during recording or while the unit is standing by for timer
recording.
—
Cannot edit or format a card.
≥Release the card’s protection setting. (With some cards, the “Write protection Off” message
sometimes appears on the screen even when protection has been set.)
40
The contents of the card
cannot be read.
≥The card format is not compatible with the unit. (The contents on the card may be
damaged.)
Format using FAT 12 or FAT 16 with other equipment or format the card with this unit.
≥The card contains a folder structure and/or file extensions that are not compatible with this
unit.
≥Turn off and then turn on the unit again.
15, 28
41
15
—
Transferring (dubbing),
erasing and setting protection
takes a long time.
≥When there are a lot of folders and files, it may sometimes take a few hours.
≥When repeating transferring (dubbing) or erasing, it may sometimes take a long time.
Format the disc or card.
—
41
The PC card cannot be
removed.
≥Make sure the PC card is slotted home firmly before attempting to remove.
28
Reference
Product Service
1. Damage requiring service—The unit should be serviced by qualified service personnel if:
(a) The AC power supply cord or AC adaptor has been damaged; or
(b) Objects or liquids have gotten into the unit; or
(c) The unit has been exposed to rain; or
(d) The unit does not operate normally or exhibits a marked change in performance; or
(e) The unit has been dropped or the cabinet damaged.
2. Servicing—Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servicing to authorized
servicing personnel.
3. Replacement parts—When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same
characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards.
4. Safety check—After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition.
Product information
For product information or assistance with product operation:
Refer to “Customer Services Directory” on page 55.
Maintenance/Disc and card handling
Unit care
The precision parts in this unit are readily affected by the
environment, especially temperature, humidity, and dust.
Cigarette smoke also can cause malfunction or breakdown.
To clean this unit, wipe with a soft, dry cloth.
≥Never use alcohol, paint thinner or benzine to clean this unit.
≥Before using chemically treated cloth, read the instructions that
came with the cloth carefully.
Observe the following points to ensure continued listening and
viewing pleasure.
Dust and dirt may adhere to the unit’s lens over time, making it
impossible to record or play discs.
Use the DVD-RAM/PD lens cleaner (LF-K123LCA1, where
available) about once every year, depending on frequency of use
and the operating environment. Read the lens cleaner’s instructions
carefully before use.
Disc and card handling
∫ How to hold a disc or
card
Do not touch the recorded
surface or the terminal surface.
RQT7303
54
∫ If there is dirt or condensation on the disc
[RAM] [DVD-R]
≥Clean with an optional DVD-RAM/PD disc cleaner (LF-K200DCA1,
where available).
≥Do not use cleaners for CDs or cloths.
[DVD-A] [DVD-V] [VCD] [CD]
Wipe with a damp cloth and then wipe dry.
∫ Handling precautions
≥Do not attach labels or stickers to discs. (This may cause disc
warping and un-balanced rotation, rendering it unusable.)
≥Do not write on the label side with a ball-point pen or other writing
instrument.
≥Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
≥Do not use scratch-proof protectors or covers.
≥Do not expose the terminals of the card to water, garbage or other
strange things.
≥Do not use the following discs:
–Discs with exposed adhesive from removed stickers or labels
(rented discs, etc).
–Discs that are badly warped or cracked.
–Irregularly shaped discs, such as heart
shapes.
≥Do not place in the following areas:
–In direct sunlight.
–In very dusty or humid areas.
–Near a heater.
–Where static electricity or electromagnetic waves occur.
7303en.book 55 ページ
2004年5月31日 月曜日 午前9時32分
Limited Warranty
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company, Division of Matsushita Electric
of Puerto Rico, Inc.,
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic DVD Recorder
Limited Warranty
Parts
Labor
DVD Recorder
Product or Part Name
One (1) Year
One (1) Year
Rechargeable Batteries,
DVD-RAM Disc (in
exchange for defective
item)
Ten (10) Days
Not Applicable
During the “Labor” warranty period there will be no charge for labor. During the “Parts”
warranty period, there will be no charge for parts. You must carry-in or mail-in your product
during the warranty period. If non-rechargeable batteries are included, they are not
warranted. This warranty only applies to products purchased and serviced in the United
States or Puerto Rico. This warranty is extended only to the original purchaser of a new
product which was not sold “as is”. A purchase receipt or other proof of the original
purchase date is required for warranty service.
Carry-In or Mail-In Service
For Carry-In or Mail-In Service in the United States call 1-800-211-PANA (7262) or visit
Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax
(787)-768-2910.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and
DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES
NOT COVER damages which occurred in shipment, or failures which are caused by
products not supplied by the warrantor, or failures which result from accidents, misuse,
abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up
adjustments, misadjustment of consumer controls, improper maintenance, power line
surge, lightning damage, modification, or commercial use (such as in a hotel, office,
restaurant, or other business), rental use of the product, service by anyone other than a
Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of
God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY. (As examples, this excludes damages for lost time, travel
to and from the servicer, loss of media or images, data or other recorded
content. The items listed are not exclusive, but are for illustration only.) ALL
EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED
WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts,
so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state. If a problem with this product develops
during or after the warranty period, you may contact your dealer or
Servicenter. If the problem is not handled to your satisfaction, then write to the
warrantor’s Consumer Affairs Department at the addresses listed for the
warrantor.
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY ARE YOUR RESPONSIBILITY.
Reference
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively
referred to as “the warrantor”) will, for the length of the period indicated on the chart below,
which starts with the date of original purchase (“warranty period”), at its option either (a)
repair your product with new or refurbished parts, or (b) replace it with a new or a
refurbished product. The decision to repair or replace will be made by the warrantor.
Customer Services Directory
Obtain Product Information and Operating Assistance; locate your nearest Dealer or Servicenter; purchase Parts and
Accessories; or make Customer Service and Literature requests by visiting our Web Site at:
http://www.panasonic.com/support
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
Accessory Purchases
Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:
http://www.pasc.panasonic.com
or, send your request by E-mail to:
npcparts@panasonic.com
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday – Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company
Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300, Fax (787)768-2910
F1003
RQT7303
55
7303en.book 56 ページ
2004年5月31日 月曜日 午前9時32分
Instalación básica
Guía de referencia rápida en español
Español
Conexión de un televisor y
videograbadora
Conexión de un receptor de TV por
cable
Consulte la ilustración que aparece en la página 7 de la sección
en idioma inglés.
Consulte la ilustración que aparece en la página 8 de la sección
en idioma inglés.
≥Las conexiones del equipo descritas son ejemplos.
≥Antes de hacer la conexión, apague todos los equipos y lea los
manuales de instrucciones apropiados.
≥El equipo periférico y los cables opcionales se venden por
separado a menos que se indique lo contrario.
≥Necesita suscribirse a los servicios de TV por cable para ver su
programación.
≥Consulte a su proveedor de servicios en cuanto al receptor de TV
por cable apropiado.
≥Si recibe únicamente su programación de un servicio de
satélite, la guía de programas de esta unidad no recibirá las
listas de programas ni la información de los canales. Sin esta
información no se podrán hacer grabaciones basadas en
programas. Sin embargo, sí se podrán hacer grabaciones
manualmente.
A
indica accesorios incluidos.
indica accesorios no incluidos.
1 – 4 son conexiones necesarias. Conecte siguiendo el
orden numerado.
B
Televisión
C
Cuando haga esta conexión, asegúrese de conectar los
cables de audio a los terminales de entrada de audio
correspondientes del televisor.
A
Televisión
B
Esta unidad
C
Cable de audio/vídeo§
D
TV por cable
D
Cable coaxial de 75 ≠§
E
Antena exterior
E
F
Antena interior
G
Cable de alimentación de CA
Conecte solamente después de haber terminado todas las
otras conexiones.
H
Rojo Blanco Amarillo
I
A una toma de CA de casa
(CA 120 V, 60 Hz)
IR Blaster
Introduzca el conector IR Blaster en el terminal G-LINK.
El receptor de TV por cable está controlado por una señal
IR transmitida a través del IR Blaster.
Cuando seleccione canales en esta unidad, los canales
correspondientes del receptor de TV por cable también
cambiarán en conformidad.
≥Utilice solamente el IR Blaster suministrado.
F
Use IN3 (L3) [no IN1 (L1)].
J
Cable coaxial de 75 ≠
➡ abajo
G
Rojo Blanco Amarillo
H
Conecte al terminal RF IN o IN3 (L3) de esta unidad.
K
Cable de antena
I
Cable de S-Vídeo
L
A la antena
J
M
Ajuste del IR Blaster ➡ abajo
Cable de audio/vídeo
K
Receptor de TV por cable
N
Cable de S-Vídeo
L
De la antena o toma de TV por cable
O
Cable de vídeo componente
P
Divisor
Q
A OUT1 o OUT2
R
Ventilador de refrigeración
S
A IN1 (L1)
T
Esta unidad
U
Terminal S-VIDEO OUT
El terminal S-VIDEO OUT proporciona una imagen más
viva que la del terminal VIDEO OUT. (Los resultados
reales dependen del televisor.)
V
Utilice un divisor si también quiere conectar la antena a su
videograbadora.
W
Terminal COMPONENT VIDEO OUT
Estos terminales se pueden utilizar para la salida
entrelazada o progresiva y para proporcionar una imagen
más pura que la del terminal S-VIDEO OUT.
≥Conecte a los terminales del mismo color.
X
Videograbadora
§ Para más información de las conexiones (➡ izquierda)
∫ ¿Debo usar el terminal AUDIO/VIDEO OUT o el
RF OUT?
Si su receptor de TV por cable tiene terminales AUDIO/VIDEO OUT
y RF OUT, le recomendamos conectar el terminal AUDIO/VIDEO
OUT al terminal IN3 (L3) de la unidad. Esta conexión proporciona la
mejor calidad de imagen.
≥El terminal S-VIDEO proporciona una imagen más viva que la del
terminal VIDEO.
Ajuste del IR Blaster
Coloque el IR Blaster delante del sensor de señales del receptor de
TV por cable.
M
Lea las instrucciones del receptor de TV por cable
relacionadas con la posición del sensor de señales.
N
Si es necesario, utilice cinta con adhesivo en ambas caras
(incluida) para asegurar el IR Blaster a una superficie
plana.
O
Ej. Superficie de base de televisión
P
Receptor de TV por cable
Q
Si despega la cinta adhesiva, la superficie podrá dañarse.
Después de confirmar que el receptor de TV por cable
esté funcionando correctamente, asegúrelo empleando la
cinta adhesiva.
∫ Cable coaxial de 75 ≠
La señal de imagen y sonido procedente de este aparato no pasa a
través del cable coaxial de 75 ≠ al televisor. Asegúrese de conectar
uno de los terminales siguientes de este aparato al televisor: el
terminal AUDIO/VIDEO OUT, el terminal S-VIDEO OUT o el terminal
COMPONENT VIDEO OUT. Si el televisor no tiene ninguno de estos
terminales, consulte a su concesionario local.
RQT7303
56
No conecte la unidad a través de una videograbadora
Las señales de vídeo que pasan a través de videograbadoras
afectarán a los sistemas de protección del copyright, y la imagen no
se mostrará correctamente en el televisor.
≥Cuando conecte a un televisor con videograbadora incorporada,
conecte a los terminales de entrada del televisor, no a los de la
videograbadora.
7303en.book 57 ページ
2004年5月31日 月曜日 午前9時32分
Ranura de tarjeta PC
Bandeja de disco < OPEN/CLOSE
OPEN/CLOSE
SD CARD
PC CARD
REC
EJECT
POWER
TIME SLIP
DVD
SD
PC
TIME SLIP
DRIVE SELECT
/x1.3
CH
Indicador Time Slip
Ranura de tarjeta SD
Indicador DVD, SD, PC
DVD POWER
Í DVD POWER
–Si el receptor de TV por cable ha cambiado al canal 09,
seleccione “Yes” (Sí) y pulse [ENTER].
–Si el receptor de TV por cable sigue sintonizado al mismo
canal, seleccione “No” y pulse [ENTER]. Repita este paso
hasta que el receptor de TV por cable cambie al canal 09.
TV
POWER
INPUT SELECT TV/VIDEO
DVD
VOLUME
CH
DRIVE SELECT
SD/PC
Si está usando un receptor de TV por cable, ajuste lo
siguiente:
≥Canales de conexión del receptor de TV por cable (Ch2/Ch3/
Ch4/L3)
≥Marca del receptor de TV por cable
≥Código de señal IR
Asegúrese de que su receptor de TV por cable sintonice el
canal que aparece en la pantalla y pulse [ENTER]. Se hace una
prueba.
DVD, SD/PC
El contenido ajustado se visualiza junto
PAGE
Botones
numerados
1
2
3
CH
4
5
6
7
8
9
PAGE WX CH
Zip code - 11111 (USA)
Cable
- Yes
Cable box - No
AUDIO
:9
;
∫
SKIP
STOP
CM SKIP
SLOW/SEARCH
PAUSE
1
DIRECT NAVIGATOR
DIRECT NAVIGATOR
TOP MENU
TOP MENU
3421
ENTER
2; ;1
SUB MENU
RETURN
SUB MENU
PROG/CHECK DISPLAY TIME SLIP TV GUIDE
Botón “Azul”
SETUP
Info
Una vez confirmado el contenido introducido aparece la
pantalla siguiente.
FUNCTIONS
ENTER
SETUP
65
PLAY/x1.3
ERASE REC MODE
REC
CHAPTER STATUS
–Si la información es correcta, seleccione “Yes, end setup” (Sí,
finalice la preparación) y pulse [ENTER].
–Si la información no es correcta, seleccione “No, repeat setup
process” (No, repita el proceso de preparación) y pulse
[ENTER] para iniciar de nuevo el ajuste.
RETURN
TIME SLIP
TV GUIDE
REC MODE
¥ REC
Botón “Verde”
(CHAPTER)
Preparación del sistema de guía de TV
en pantalla
Después de enchufar la unidad en una toma de CA de casa y pulsar
[Í DVD POWER] para encender la unidad por primera vez, ésta
inicia la preparación del sistema de guía de TV en pantalla.
En el sistema de guía de TV en pantalla sólo se
muestra inglés. No se pueden mostrar otros idiomas.
Preparación
≥Encienda el televisor y seleccione la entrada de vídeo apropiada a
las conexiones de esta unidad.
≥Cuando use el receptor de TV por cable, compruebe lo siguiente.
–Asegúrese de que IR Blaster esté conectado y posicionado
correctamente (➡ páginas 8, 56).
–Asegúrese de que el receptor de TV por cable esté encendido.
1 Pulse [Í DVD POWER].
2 Prepare el entorno de funcionamiento de su televisor
siguiendo los mensajes de la pantalla.
≥Mueva el cursor con [3, 4, 2, 1] y pulse [ENTER] para
confirmar.
≥Pulse los botones numerados para introducir números.
≥Pulse [ENTER] para avanzar a la pantalla siguiente.
≥Consulte las indicaciones de la parte inferior de la pantalla.
Ajuste lo siguiente:
≥País [USA (EE.UU.)/Canada (Canadá)]
≥Código postal
≥Servicio de TV por cable conectado a esta unidad [Yes (Sí)/No]
≥Receptor de TV por cable conectado a esta unidad
[Yes (Sí)/No]
What would you like to do now?
Español
0
Watch TV
3 Pulse [ENTER].
Se muestra una pantalla de recepción de televisión o una
pantalla con fondo azul.
4 Pulse [Í DVD POWER].
Deje la unidad apagada hasta que descargue la lista de programas
de televisión. Esto puede tardar un máximo de 24 horas.
Cuando la unidad esté conectada a un receptor de TV por cable
≥El receptor de TV por cable deberá encenderse para poder
descargar la lista de programas de televisión.
≥Tenga en cuenta que la lista de programas de televisión tal vez no
pueda descargarse correctamente si usted cambia el canal del
receptor de TV por cable mientras la unidad está apagada.
Seleccione el idioma y el tipo de
televisión
Guía de referencia rápida en español
VCR Plus+ CM SKIP
CANCEL
1 Pulse [SETUP].
2 Pulse [3, 4] para seleccionar “Display” y pulse [1].
3 Pulse [3, 4] para seleccionar “On-screen Language” y
pulse [ENTER].
4 Pulse [3, 4] para seleccionar “Español” y pulse [ENTER].
5 Pulse [2].
6 Pulse [3, 4] para seleccionar “Pantalla TV” y pulse [1].
7 Pulse [3, 4] para seleccionar “Tipo TV” y pulse [ENTER].
≥Aspecto 4:3/Aspecto 16:9:
4:3
16:9
Televisor de aspecto
Televisor panorámico 16:9
estándar 4:3
≥480P/480I:
Seleccione “480P” si el televisor es compatible con salida
progresiva.
8 Pulse [3, 4] para seleccionar el elemento y pulse [ENTER].
Para salir de la pantalla
Pulse [SETUP].
Para volver a la pantalla anterior
Pulse [RETURN].
RQT7303
57
7303en.book 58 ページ
2004年5月31日 月曜日 午前9時32分
Grabación de programas de televisión
Consulte la referencia de controles en la página 57.
[RAM] [DVD-R]
≥Puede grabar hasta 99 títulos en un disco.
≥No es posible grabar continuamente desde una cara a la otra en
un disco de dos caras. Tendrá que expulsar el disco y darlo la
vuelta.
≥Cuando utilice discos DVD-RAM de 8 cm (3″ ), retire el disco del
cartucho.
≥No es posible grabar material protegido CPRM (protección del
contenido de medios grabables) en discos DVD-R o DVD-RAM de
2,8 GB.
≥No es posible grabar en una tarjeta.
Utilización del sistema de guía de TV en
pantalla para hacer grabaciones con
temporizador
Puede realizar grabaciones con temporizador fácilmente marcando
simplemente los programas deseados de una lista de programas de
televisión.
≥Puede marcar el programa deseado con hasta 8 días de antelación.
≥El nombre del programa se convierte en el título grabado si el
programa está en la lista de programas de televisión.
Preparación
≥Pulse [RETURN] para salir de la lista de programas de televisión si
ésta se visualiza en el televisor.
SCHEDULE
TODAY
Español
Guía de referencia rápida en español
RECORD
INFO.
R
NWBG
ducation
Guía en pantalla
PBS
Aquí se muestran
la función del
botón “Verde” y del botón “Azul”.
BOX
ANiMe
Network
≥Para saltar una pantalla
Pulse [PAGE WX CH].
≥Para saltar 24 horas en la lista
Pulse [3, 4, 2, 1] para seleccionar “LISTINGS” y:
Pulse el botón “Verde” (avance).
Pulse el botón “Azul” (retroceso).
Insértelo con la flecha hacia adentro.
3 Pulse [W X CH] para seleccionar el canal.
Ej.,
5: [0] ➡ [5]
15: [1] ➡ [5]
Ej.,
5:
[0] ➡ [0] ➡ [5]
15: [0] ➡ [1] ➡ [5]
115: [1] ➡ [1] ➡ [5]
4 Pulse [REC MODE] para seleccionar el modo de
grabación (XP, SP, LP o EP).
5 Pulse [¥ REC] para empezar a grabar.
La grabación se hará en el espacio vacío del disco. Los datos no
se escribirán encima de otros.
≥Durante la grabación no se puede cambiar el canal ni el modo
de grabación.
Para detener la grabación
Pulse [∫].
La sección desde que empieza hasta que termina la grabación es
un título.
Para hacer una pausa en la grabación
Pulse [;].
Pulse de nuevo para reiniciar la grabación.
(El título no se divide en un título separado.)
Dependiendo del contenido que está siendo grabado, los tiempos
de grabación pueden ser inferiores a los indicados.
(Unidad: hora)
DVD-RAM
DVD-R
(4,7
Modo
Una cara
Dos caras
GB)
(4,7 GB)
(9,4 GB)
XP (Alta calidad)
1
2
1
SP (Normal)
2
4
2
EP
(Duración extralarga)
§
“ R ” aparece en la lista para indicar que el programa está
preparado para la grabación con temporizador. Si se registra un
programa que está siendo emitido, la grabación con
temporizador empezará automáticamente.
≥Pulse el botón “Verde” para cancelar.
≥Pulse varias veces el botón “Azul” para cambiar la frecuencia
de grabación. (➡arriba. Marca de grabación y frecuencia de
grabación)
Repita los pasos 2–3 para programar otras grabaciones.
4 Pulse [TV GUIDE].
El mensaje “LA GRAB. TEMP.DA SE ACTIVA APAGANDO EL
GRABADOR.” se muestra en la pantalla del televisor.
5 Pulse [Í DVD POWER] para apagar el aparato.
“F” se enciende en el visualizador del aparato para indicar que la
espera de grabación con temporizador ha sido activada.
Para cancelar el modo de espera de grabación del aparato
Pulse [Í DVD POWER].
El aparato se enciende y se apaga “F”.
≥Asegúrese de pulsar [Í DVD POWER] para volver a poner el aparato
en el modo de espera antes de la hora de grabación programada. La
grabación con temporizador sólo funcionará si se visualiza “F”.
Para cancelar la grabación cuando ésta ya ha empezado
Pulse [∫] y luego [ENTER] antes de que pasen 5 segundos.
≥También puede mantener pulsado [∫] en el aparato principal
durante más de 3 segundos para detener la grabación.
[RAM]
∫ Modo de grabación
LP (Duración larga)
3 Pulse el botón “Verde”.
Reproducción mientras usted está
grabando
Para especificar un tiempo y detener la grabación
Durante la grabación
Pulse [¥ REC] para seleccionar el tiempo de grabación.
58
FAVORITES
pTV
TV
Graba una sola vez.
Graba cuando la hora
RR
de la emisión y el
nombre del programa
coinciden.
RW Graba semanalmente.
Cancela temporalmente
R la grabación con
temporizador de un
programa sin borrar el
ajuste del programa.
R
2 Pulse [3, 4, 2, 1] para seleccionar el programa.
Para seleccionar con los botones numerados:
Modo de TV (Del aire)
Modo CATV (Cable)
RQT7303
SORT
8:30PM
87
NWGB
1 Pulse [DVD] para seleccionar la unidad DVD.
2 Pulse [< OPEN/CLOSE] en la unidad principal
para abrir la bandeja e insertar un disco.
haga un ruido seco.
LISTINGS
8:00PM
Last
Channel
8:00 8:30
≥Pulse de nuevo el botón para cerrar la bandeja.
Insértelo con la cara impresa
Insértelo completamente
hacia arriba.
en su lugar hasta que
Marca de grabación y
frecuencia de grabación:
1 Pulse [TV GUIDE].
4
8
4
8 (6§)
16 (12§)
8 (6§)
Cuando “Tiempo de grab. en el modo EP” se pone en “EP (6H)” en
el menú SETUP.
La calidad del sonido es mejor cuando se utiliza “EP (6H)” que
cuando se utiliza “EP (8H)”.
Puede empezar a reproducir desde el comienzo del
Reproducción título que está grabando.
con
Pulse [1] (PLAY).
persecución El indicador de salto hacia atrás de la unidad
principal se enciende.
Mientras graba puede reproducir un título grabado
previamente.
Grabación y 1 Pulse [DIRECT NAVIGATOR].
reproducción 2 Pulse [3, 4, 2, 1] para seleccionar un título
y pulse [ENTER].
simultáneas
≥Para salir de la pantalla Direct Navigator
Pulse [DIRECT NAVIGATOR].
Time Slip
Puede revisar las imágenes grabadas mientras graba.
1 Pulse [TIME SLIP].
2 Pulse [3, 4] para seleccionar el tiempo y
pulse [ENTER].
≥Pulse [TIME SLIP] para mostrar las imágenes de
reproducción completas. Pulse de nuevo para
mostrar las imágenes de reproducción y grabación.
Para detener la reproducción
Pulse [∫].
Para detener la grabación
(2 segundos después se detiene la reproducción) Pulse [∫].
7303en.book 59 ページ
2004年5月31日 月曜日 午前9時32分
Reproducción de discos y tarjetas
Consulte la referencia de controles en la página 57
.
1 Pulse [DVD] para seleccionar la unidad DVD.
2 Pulse [< OPEN/CLOSE] en la unidad principal
para abrir la bandeja e insertar un disco.
Pulse de nuevo el botón para cerrar la bandeja.
3 Pulse [1] (PLAY).
[RAM] [DVD-R]
La reproducción empieza desde el título grabado más recientemente.
[DVD-A] [DVD-V] [VCD] [CD]
La reproducción empieza desde el comienzo del disco.
∫ Selección de programas (títulos) grabados para
reproducir
[RAM] [DVD-R]
1 Pulse [DIRECT NAVIGATOR]. DIRECT NAVIGATOR Vista titulo
VIDEO
DVD-RAM
2 Pulse [3, 4, 2, 1] para
seleccionar la ficha “VIDEO”
y luego pulse [ENTER].
3 Pulse [3, 4, 2, 1] para
seleccionar el título y pulse
[ENTER].
Ant.
02/02
Sig.
También puede seleccionar
SUB MENU
Seleccionar
títulos con los botones
numerados.
Ej., 5:
[0] ➡ [5]
15: [1] ➡ [5]
07
08
10 10/27 Lun
8 10/27 Lun
--
--
IMAGEN
--
--
Repr.
Para salir de la pantalla
Pulse [DIRECT NAVIGATOR].
∫ Cuando aparece una pantalla de menú en el televisor
[DVD-A] [DVD-V]
Pulse [3, 4, 2, 1] para seleccionar el elemento y pulse [ENTER].
Algunos elementos también se pueden seleccionar con los botones
numerados.
[VCD]
Pulse los botones numerados para seleccionar el elemento.
Ej., 5:
[0] ➡ [5]
15: [1] ➡ [5]
≥Para volver a la pantalla de menú
[DVD-A] Pulse [TOP MENU].
[DVD-V] Pulse [TOP MENU] o [SUB MENU].
[VCD] Pulse [RETURN].
Operaciones durante la reproducción
Pulse [∫].
La posición de parada se memoriza.
“PLAY” parpadea en el
DVD - R AM
visualizador del aparato.
PLAY
(Excepto
cuando
se
reproduce
Parada
desde Direct Navigator y cuando
se reproduce una lista de reproducción.)
Función de reanudación de la reproducción
Pulse [1] (PLAY) para reanudar la reproducción
desde esta posición.
Pulse [;].
Pausa
Pulse de nuevo para reiniciar la reproducción.
Pulse [6] o [5].
≥En el aparato principal, mantenga pulsado
Búsqueda
[D] o [E].
≥La velocidad aumenta hasta 5 pasos.
≥Pulse [1] (PLAY) para reiniciar la reproducción.
Pulse [:] o [9].
≥En el aparato principal, pulse [D] o
Salto
[E].
≥Cada pulsación aumenta el número de saltos.
Pulse los botones numerados.
Ej., 5:
[0] ➡ [5]
15: [1] ➡ [5]
[CD] (Discos MP3 solamente)
Inicio desde
5:
[0] ➡ [0] ➡ [5] 15: [0] ➡ [1] ➡ [5]
un elemento [DVD-A] Selección de grupos
seleccionado Durante la parada (el salvapantallas se visualiza en
el televisor)
5:
[5]
≥Esto sólo funciona durante la parada con algunos
discos (el salvapantalla está en el televisor).
La velocidad de reproducción puede aumentar sin
Visión rápida distorsionar el audio.
Mantenga pulsado [1] (PLAY/a1.3).
[RAM]
≥Pulse de nuevo para volver a la velocidad normal.
Durante la pausa, pulse [6] o [5].
≥En el aparato principal, mantenga pulsado
[D] o [E].
≥La velocidad aumenta hasta 5 pasos.
≥Pulse [1] (PLAY) para reiniciar la reproducción.
≥Sentido de avance solamente. [VCD]
Durante la pausa, pulse [2;] o [;1].
≥Cada pulsación muestra el cuadro siguiente.
≥Pulse [1] (PLAY) de nuevo para reiniciar la
reproducción.
≥Sentido de avance solamente. [VCD]
Pulse [TIME SLIP].
La unidad muestra la imagen del televisor en el
modo de imagen en imagen.
≥Pulse de nuevo [TIME SLIP] para cancelar.
1 Pulse [TIME SLIP].
Salto del
2 Pulse [3, 4] para seleccionar el tiempo y
tiempo
pulse [ENTER].
especificado
La reproducción salta el tiempo especificado.
(Time Slip)
≥Pulse [TIME SLIP] para mostrar las imágenes
[RAM] [DVD-R]
de reproducción completas.
La reproducción se reanuda un minuto después
Salto CM
aproximadamente.
[RAM] [DVD-R] Pulse [CM SKIP].
Reproducción de imágenes fijas
Introduzca o saque la tarjeta SD/PC sólo después de apagar la
unidad.
Cuando parpadee el indicador de tarjeta (“SD” o “PC”) en el visualizador
de la unidad, la tarjeta estará siendo leída o se estará escribiendo en
ella. No apague la unidad ni saque la tarjeta. Esto puede causar un fallo
en el funcionamiento o hacer que se pierda el contenido de la tarjeta.
∫ Ranura de tarjeta SD
EJECT
PC CARD
SD CARD
POWER
Inserción de la tarjeta
Insértela con la cara de la etiqueta
hacia arriba y con la esquina
recortada hacia la derecha.
Insértela recta hasta que quede
acoplada en su lugar.
Extracción de la tarjeta
Presione en el centro de la tarjeta.
Sáquela recta.
∫ Ranura de tarjeta PC
Inserción de la tarjeta
Sujete el borde de la tarjeta e insértela hasta que quede bien colocada.
≥Si utiliza el adaptador, no presione directamente la tarjeta.
Extracción de la tarjeta
1Empuje El botón de
2 Empuje
expulsión sale
otra vez
Español
≥No es posible reproducir continuamente desde una cara a la otra en
un disco de dos caras. Tendrá que expulsar el disco y darlo la vuelta.
≥Cuando utilice discos DVD-RAM de 8 cm (3″ ), retire el disco del
cartucho.
Preparación
≥Pulse [RETURN] para salir de la lista de programas de televisión si
ésta se visualiza en el televisor.
Cámara
lenta
[RAM] [DVD-R]
[DVD-A]
(Parte de
pelicula
solamente)
[DVD-V] [VCD]
Cuadro a
cuadro
[RAM] [DVD-R]
[DVD-A]
(Parte de
pelicula
solamente)
[DVD-V] [VCD]
Visualización
de la imagen
de televisión
en el modo
de imagen
en imagen
Guía de referencia rápida en español
Reproducción del contenido de vídeo
grabado/reproducción de discos solamente
EJECT
PC CARD
SD CARD
2
EJECT
PC CARD
EJECT
PC CARD
EJECT
PC CARD
1
2 alinee para que concuerde la marca
Lado con etiqueta hacia arriba
Conexiones de terminales hacia el interior de la unidad
[RAM] [SD] [PC]
1 Pulse [DVD] o [SD/PC] para seleccionar la unidad.
≥Cada vez que pulse [SD/PC]:
Unidad de tarjeta SD ,". Unidad de tarjeta PC
2 Pulse [DIRECT NAVIGATOR].
3 [RAM]
Pulse [3, 4, 2, 1] para seleccionar la ficha
“IMAGEN” y luego pulse [ENTER].
4 Pulse [3, 4, 2, 1] para seleccionar la imagen
fija y luego pulse [ENTER].
≥Pulse [2, 1] para visualizar la imagen fija anterior o siguiente.
∫ Para seleccionar imágenes fijas en otra carpeta
1 Pulse [3, 4, 2, 1] para seleccionar “Carpeta” y pulse [ENTER].
2 Pulse [3, 4] para seleccionar la carpeta y pulse [ENTER].
Para detener la reproducción
Pulse [∫]
Para salir de la pantalla
Pulse [DIRECT NAVIGATOR].
RQT7303
59
7303en.book 60 ページ
2004年5月31日 月曜日 午前9時32分
Index
Angle. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna system . . . . . . . . . . . . . . . . . .
Audio
attribute . . . . . . . . . . . . . . . . . . . . . .
language . . . . . . . . . . . . . . . . . . . . .
playback. . . . . . . . . . . . . . . . . . . . . .
receiving, recording . . . . . . . . . . . . .
30
42
30
42
26
17
Change Thumbnail . . . . . . . . . . . . . . . . 33
Channel
adjusting, hiding. . . . . . . . . . . . . . . . 23
audio . . . . . . . . . . . . . . . . . . . . . . . . 30
Auto Channel Setting. . . . . . . . . . . . 45
captions . . . . . . . . . . . . . . . . . . . . . . 46
Chapter . . . . . . . . . . . . . . . . . . . . . . . 26, 32
Chasing playback . . . . . . . . . . . . . . . . . 18
Cleaning
disc . . . . . . . . . . . . . . . . . . . . . . . . . 54
lens . . . . . . . . . . . . . . . . . . . . . . . . . 54
main unit . . . . . . . . . . . . . . . . . . . . . 54
Clock setting . . . . . . . . . . . . . . . . . . 11, 45
CM Skip. . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connection
amplifier, system component . . . . . . 9
antenna . . . . . . . . . . . . . . . . . . . 7, 8, 9
cable TV box . . . . . . . . . . . . . . . . . . . 8
IR Blaster . . . . . . . . . . . . . . . . . . . . . . 8
L2 input terminals . . . . . . . . . . . . . . 39
television . . . . . . . . . . . . . . . . . . . . . . 7
video cassette recorder . . . . . . . . 7, 39
Copy (play list) . . . . . . . . . . . . . . . . . . . . 35
CPRM . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Create play lists . . . . . . . . . . . . . . . . . . . 34
Dialog Enhancer . . . . . . . . . . . . . . . . . . 31
Direct Navigator . . . . . . . . . . 24, 29, 32, 36
Divide Chapter . . . . . . . . . . . . . . . . . . . . 33
Divide Title . . . . . . . . . . . . . . . . . . . . . . . 33
DPOF. . . . . . . . . . . . . . . . . . . . . . . . . 36, 48
DVD-R (Enabling DVD-R to be played
on other equipment—Finalize). . . . . . 41
DVD-RAM, DVD-R . . . . . . . . . . . . . . . . . 14
Enter name
disc . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Entering text . . . . . . . . . . . . . . . . . . . 37
Folder . . . . . . . . . . . . . . . . . . . . . . . . 36
play list . . . . . . . . . . . . . . . . . . . . . . . 35
title . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Erase
All titles . . . . . . . . . . . . . . . . . . . . . . . 41
chapter . . . . . . . . . . . . . . . . . 26, 33, 35
Folder . . . . . . . . . . . . . . . . . . . . . . . . 36
play list . . . . . . . . . . . . . . . . . . . . 26, 35
still picture. . . . . . . . . . . . . . . . . . . . . 36
title . . . . . . . . . . . . . . . . . . . . . . . 26, 33
Favorite . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Finalize . . . . . . . . . . . . . . . . . . . . . . . 41, 48
Flexible Recording . . . . . . . . . . . . . . . . . 18
Format . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FR (Flexible Recording Mode) . . . . . . . . 17
FUNCTIONS window. . . . . . . . . . . . . . . . 40
JPEG . . . . . . . . . . . . . . . . . . . . . . . . . 28, 48
Language
audio . . . . . . . . . . . . . . . . . . . . . . . . . 42
code list . . . . . . . . . . . . . . . . . . . . . . 50
on-screen . . . . . . . . . . . . . . . . . . . . . 44
sound track . . . . . . . . . . . . . . . . . . . . 30
subtitle . . . . . . . . . . . . . . . . . . . . 30, 42
LPCM . . . . . . . . . . . . . . . . . . . . . . . . . 44, 48
Menu
MP3 . . . . . . . . . . . . . . . . . . . . . . . . . 27
on-screen . . . . . . . . . . . . . . . . . . . . . 30
SETUP . . . . . . . . . . . . . . . . . . . . . . . 42
Mode
recording. . . . . . . . . . . . . . . . . . . . . . 17
Still Mode . . . . . . . . . . . . . . . . . . . . . 43
MPEG-DNR . . . . . . . . . . . . . . . . . . . . . . . 31
MP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Noise reduction (NR)
Integrated DNR. . . . . . . . . . . . . . . . . 31
Line-in NR. . . . . . . . . . . . . . . . . . . . . 43
MPEG-DNR . . . . . . . . . . . . . . . . . . . 31
3D NR . . . . . . . . . . . . . . . . . . . . . . . . 31
On-screen
language . . . . . . . . . . . . . . . . . . . . . . 44
menus . . . . . . . . . . . . . . . . . . . . . . . . 30
Status messages . . . . . . . . . . . . . . . 31
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
“DTS” and “DTS 2.0 i Digital Out” are trademarks of Digital Theater
Systems, Inc.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and
4,819,098, licensed for limited viewing uses only.
MPEG Layer-3 audio decoding technology licensed from Fraunhofer
IIS and Thomson multimedia.
Quick View . . . . . . . . . . . . . . . . . . . . . . . .25
Ratings level . . . . . . . . . . . . . . . . . . . . . .43
Recording
Flexible Recording. . . . . . . . . . . . . . .18
mode . . . . . . . . . . . . . . . . . . . . . . . . .17
timer. . . . . . . . . . . . . . . . . . . . . . .19–22
Re-initialize settings . . . . . . . . . . . . . . . .42
Remote control code . . . . . . . . . . . . . . . .13
Repeat play . . . . . . . . . . . . . . . . . . . . . . .31
Resume play function . . . . . . . . . . . . . . .25
SD card . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SETUP menu . . . . . . . . . . . . . . . . . . . . . .42
Shorten (titles) . . . . . . . . . . . . . . . . . . . . .33
Simultaneous rec and play . . . . . . . . . . .18
Sound track . . . . . . . . . . . . . . . . . . . . . . .30
Status messages . . . . . . . . . . . . . . . . . . .31
Still pictures
Edit . . . . . . . . . . . . . . . . . . . . . . . . . .36
Play . . . . . . . . . . . . . . . . . . . . . . . . . .28
Transferring (dubbing) . . . . . . . . . . . .38
Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . .30
TIFF . . . . . . . . . . . . . . . . . . . . . . . . . . .28, 48
Time Slip. . . . . . . . . . . . . . . . . . . . . . .18, 25
Timer recording . . . . . . . . . . . . . . . . .19–22
Transfer . . . . . . . . . . . . . . . . . . . . . . . . . .31
Transfer (dubbing). . . . . . . . . . . . . . . . . .38
TV Guide On ScreenTM . . . . . . . . . . . .19, 23
TV Type. . . . . . . . . . . . . . . . . . . . . . . . . . .12
VCR Plusi . . . . . . . . . . . . . . . . . . . . . . . .21
V.S.S. . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
≥SD logo is a trademark.
≥Portions of this product are protected under copyright law and are
provided under license by ARIS/SOLANA/4C.
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
Panasonic Sales Company,
Division of Matsushita Electric
of Puerto Rico, Inc. (“PSC”)
One Panasonic Way Secaucus,
New Jersey 07094
http://www.panasonic.com
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
C 2004 Matsushita Electric Industrial Co., Ltd.
Printed in Japan
PC card . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PCM Down Conversion . . . . . . . . . . . . . .44
Picture . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Play list . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Progressive . . . . . . . . . . . . . . . . . . . .31, 48
Properties
play list. . . . . . . . . . . . . . . . . . . . . . . .35
still picture . . . . . . . . . . . . . . . . . . . . .29
title . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Protection
card . . . . . . . . . . . . . . . . . . . . . . . . . .40
cartridge. . . . . . . . . . . . . . . . . . . . . . .40
disc . . . . . . . . . . . . . . . . . . . . . . . . . .40
folder . . . . . . . . . . . . . . . . . . . . . . . . .36
still picture . . . . . . . . . . . . . . . . . . . . .36
title . . . . . . . . . . . . . . . . . . . . . . . . . . .33
pr
RQT7303-P
F0504HT0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising