Panasonic | SCHT07 | Operating instructions | Panasonic SCHT07 Operating Instructions

SC-HT07EB-EN.fm
Page 1
Friday, May 7, 2004
4:29 PM
TOP MENU
VOLUME
MULTI CONTROL
PREV /
8
ENTER
NEXT /
SFC
^
INPUT SELECTOR
VIDEO IN
MUSIC
AV/MOVE
TUNE
TUNE
L AUDIO IN R VCR 2
RETURN
DOWN
UP PHONES
Home Theater Audio System
Operating Instructions
Model No.
SC-HT07
Dear customer
Thank you for purchasing this product.
Before connecting, operating or adjusting this product, please
read these instructions completely.
Please keep this manual for future reference.
SC-HT07 is used in the illustrations unless otherwise
mentioned.
SC-HT05 is only for continental Europe, the United
Kingdom, Australia, and New Zealand.
Note:
“EB” on the packaging indicates the United Kingdom.
SC-HT07
SC-HT05
Table of contents
Before use
Caution for AC Mains Lead................................... 2
Safety precautions................................................. 2
Supplied accessories ............................................ 3
Step 1
Speaker setup
4
Step 2
Home theater
connections
8
Step 3
Other connections
10
Step 4
Settings
12
Operations
Basic operations.................................................. 13
Control guide ....................................................... 14
The radio............................................................... 18
Other functions .................................................... 19
Using the VCR2 terminals (for SC-HT07)........... 22
Making a recording.............................................. 22
The RESET function ............................................ 22
Remote control operation guide ........................ 23
Advance setup ..................................................... 26
Reference
Specifications ...................................................... 27
Maintenance ......................................................... 27
Troubleshooting guide ......................... Back cover
EP EB GCS GN
RQT7384-3B
SC-HT07EB-EN.fm
Page 2
Friday, May 7, 2004
4:29 PM
Caution for AC Mains Lead
(For United Kingdom)
Placement
(“EB” area code model only)
Before use
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5-ampere and that it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of
the fuse.
If the plug contains a removable fuse cover you must ensure that
it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local dealer.
CAUTION!
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR
THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE
SHOULD BE REMOVED AND THE PLUG CUT OFF AND
DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK
IF THE CUT OFF PLUG IS INSERTED INTO ANY 13AMPERE SOCKET.
If a new plug is to be fitted please observe the wiring code as
stated below.
If in any doubt please consult a qualified electrician.
IMPORTANT
The wires in this mains lead are coloured in accordance with the
following code:
Blue: Neutral, Brown: Live.
As these colours may not correspond with the coloured
markings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Black or Blue.
The wire which is coloured Brown must be connected to the
terminal which is marked with the letter L or coloured Brown or Red.
WARNING: DO NOT CONNECT EITHER WIRE TO THE
EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E, BY THE EARTH SYMBOL
OR
COLOURED GREEN OR GREEN/YELLOW.
THIS PLUG IS NOT WATERPROOF–KEEP DRY.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to the type of AC mains
plug (figures A and B). Confirm the AC mains plug fitted and
follow the instructions below.
Illustrations may differ from actual AC mains plug.
1. Open the fuse cover with a screwdriver.
Figure B
Figure A
Fuse cover
2. Replace the fuse and close or attach the fuse cover.
RQT7384
Figure A
2
Figure B
Fuse
(5 ampere)
Safety precautions
Fuse
(5 ampere)
Set the unit up on an even surface away from direct sunlight, high
temperatures, high humidity, and excessive vibration. These conditions
can damage the cabinet and other components, thereby shortening the
unit’s service life.
Do not place heavy items on the unit.
Voltage
Do not use high voltage power sources. This can overload the unit and
cause a fire.
Do not use a DC power source. Check the source carefully when
setting the unit up on a ship or other place where DC is used.
AC mains lead protection
Ensure the AC mains lead is connected correctly and not damaged.
Poor connection and lead damage can cause fire or electric shock. Do not
pull, bend, or place heavy items on the lead.
Grasp the plug firmly when unplugging the lead. Pulling the AC mains
lead can cause electric shock.
Do not handle the plug with wet hands. This can cause electric shock.
Foreign matter
Do not let metal objects fall inside the unit. This can cause electric
shock or malfunction.
Do not let liquids get into the unit. This can cause electric shock or
malfunction. If this occurs, immediately disconnect the unit from the
power supply and contact your dealer.
Do not spray insecticides onto or into the unit. They contain flammable
gases which can ignite if sprayed into the unit.
Service
Do not attempt to repair this unit by yourself. If sound is interrupted,
indicators fail to light, smoke appears, or any other problem that is not
covered in these operating instructions occurs, disconnect the AC mains
lead and contact your dealer or an authorized service center. Electric
shock or damage to the unit can occur if the unit is repaired,
disassembled or reconstructed by unqualified persons.
Extend operating life by disconnecting the unit from the power source if it
is not to be used for a long time.
CAUTION!
Do not place anything on top of this unit or block the heat
radiation vents in any way. In particular, do not place tape
decks or CD/DVD players on this unit as heat radiated from it
can damage your software.
Page 3
Friday, May 7, 2004
4:29 PM
CAUTION!
• DO NOT INSTALL OR PLACE THIS UNIT IN A
BOOKCASE, BUILT-IN CABINET OR IN ANOTHER
CONFINED SPACE. ENSURE THE UNIT IS WELL
VENTILATED. TO PREVENT RISK OF ELECTRIC
SHOCK OR FIRE HAZARD DUE TO OVERHEATING,
ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION
VENTS.
• DO NOT OBSTRUCT THE UNIT’S VENTILATION
OPENINGS WITH NEWSPAPERS,TABLECLOTHS,
CURTAINS, AND SIMILAR ITEMS.
• DO NOT PLACE SOURCES OF NAKED FLAMES,
SUCH AS LIGHTED CANDLES, ON THE UNIT.
• DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY
FRIENDLY MANNER.
System
SC-HT07
SC-HT05
Main unit
SA-HT07
SA-HT05
Front speakers
SB-PF725
SB-FS927
Surround speakers
SB-PS725
Center speaker
SB-PC927
SB-PC725
Subwoofer
SB-WA07
SB-WA05
Supplied accessories
Please check and identify the supplied
accessories.
AC mains lead
For United
Kingdom
Before use
SC-HT07EB-EN.fm
For other areas
For Australia and
New Zealand
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE, DO NOT EXPOSE THIS
APPARATUS TO RAIN, MOISTURE, DRIPPING OR
SPLASHING AND THAT NO OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE
APPARATUS.
This product may receive radio interference caused by
mobile telephones during use. If such interference is
apparent, please increase separation between the product
and the mobile telephone.
The socket outlet shall be installed near the equipment and
easily accessible or the mains plug or an appliance coupler
shall remain readily operable.
(For continental Europe, the United Kingdom, Australia, and New
Zealand)
(RJA0053-3X) (K2CJ2DA00010) (RJA0019-2X)
Power plug adapter
(RJP1SG04-H)
(For areas except continental Europe, the United Kingdom,
Australia, and New Zealand)
System cable
(K1HA25HA0001)
FM indoor antenna
(RSA0007-L)
AM loop antenna
(N1DAAAA00002)
THIS UNIT IS INTENDED FOR USE IN MODERATE
CLIMATES.
SC-HT07
(EUR7722KE0)
Remote control transmitter
THIS UNIT IS INTENDED FOR USE IN TROPICAL
CLIMATES.
For the United Kingdom and Republic of Ireland
Batteries
(x 2)
Speaker cable(s)
SC-HT07
(REE1203A) (4 m x 1)
SC-HT05
www.panasonic.co.uk (for UK customers only)
2
1
xxxxxx
xxx
xxxxxx
xxx
xxxxxx
xxx
3
xxxxxx
xxx
4
4
3
xxxxxx
xxx
2
xxxxxx
xxx
1
xxxxxx
xxx
xxxxxx
xxx
4
xxxxxx
xxx
xxxxxx
xxx
(For the United Kingdom)
xxxxxx
xxx
2
xxxxxx
xxx
3
xxxxxx
xxx
Antenna plug adapter
xxxxxx
xxx
2
xxxxxx
xxx
5
5
xxxxxx
xxx
1
xxxxxx
xxx
1
3
Technical Support
For UK customers: 0870 1 505610
This Technical Support Hot Line number is for Panasonic PC
software related products only.
For Republic of Ireland, please use the Customer Care Centre
number listed above for all enquiries.
For all other product related enquiries, please use the Customer
Care Centre numbers listed above.
Sticker sheet
xxxxxx
xxx
Customer Care Centre
For UK customers: 08705 357357
For Republic of Ireland customers: 01 289 8333
(REE1203A) (4 m x 3)
(REE1203C) (10 m x 2)
4
• Order accessory and consumable items for your product with ease
and confidence by telephoning our Customer Care Centre MonFriday 9:00am-5:30pm. (Excluding public holidays.)
• Or go on line through our Internet Accessory ordering application.
• Most major credit and debit cards accepted.
• All enquiries transactions and distribution facilities are provided
directly by Panasonic UK Ltd.
• It couldn’t be simpler!
xxxxxx
xxx
Marking sign is located on bottom of the unit.
5
For main unit
SC-HT05
(EUR7722040)
(RQCA1029)
xxxxxx
xxx
5
(K1YZ02000013)
SC-HT07
Speaker stands
(x 4)
(RYQ0463A-S)
Stand bases
(x 4)
(RYQ0470-S)
Screws (large and small)
(XSN5+10FN) (x 8)
(XSS6+14FZ) (x 8)
Use the numbers indicated in parentheses when asking for
replacement parts.
RQT7384
(For other areas)
3
SC-HT07EB-EN.fm
Page 4
1
Step
Friday, May 7, 2004
4:29 PM
Speaker setup (for SC-HT07)
Front and surround speaker assembly
• To prevent damage or scratches, lay a soft cloth and perform assembly on it.
• For assembly, use a Phillips-head screwdriver.
Step 1
1
1
Attach the pipe to the bases.
Thread the speaker cable through the base.
3
Secure the pipe to the base.
Speaker setup (for SC-HT07)
Large screws
(included)
Groove
2
Thread the speaker cable through here.
Ensure the screws are securely fastened by lightly tightening
the left and right side screws alternately until fully tightened.
(The heads of the screws protrude slightly even if you have
fully tightened them.)
Insert the pipe.
Insert the pipe while
slightly pulling on the
speaker cable.
2
RQT7384
1
4
The supplied stands are specially designed for
attachment to Panasonic SB-FS927 front speakers
and surround speakers.
Only use as indicated in this setup.
Attach the stand to the speaker.
Ensure the stand is fastened on straight by lightly
tightening the top and bottom screws alternately
until fully tightened.
• There is no difference between the right and left
speakers and stands.
Small screws
(included)
For your reference
You can enjoy good acoustics by
adjusting the height of the front
speaker with the height of the
television so the center positions
of both are approximately the
same.
It is usually better to make the
surround speakers a little higher.
You can also attach to the upper rear of the speaker.
When attached to the upper rear, you can adjust the height of the speakers between 625 mm and 796 mm. When attached to the
lower rear, you can adjust the height of the speakers between 968 mm and 1138 mm.
(Speaker height adjustment è procedure 3)
SC-HT07EB-EN.fm
Page 5
Supplied
accessories
Friday, May 7, 2004
4:29 PM
Speaker stands
Stand bases
(x 4)
(x 4)
Stopper screw
Screw to stop mounting
plate from moving or
sliding below this point.
1
2
Loosen the attached speaker mounting plate screw until the
attached speaker is slightly loose and adjustable.
• Be careful not to loosen the screw too much or the speaker may
detach and fall.
Adjust the position of the pipe.
• After adjusting the height, tighten the screw on the mounting plate
securely.
Connect the speaker cables.
Copper
1
Connect the speaker cables.
2
Press the speaker cable into the groove.
Step 1
Adjust the speaker height.
e.g., With the stand attached
to the lower rear of the
speaker
4
(x 8)
(x 8)
Speaker setup (for SC-HT07)
3
Screws (large and small)
Silver
If there is any excess cable, thread it from the opening near the top of
the pipe while pulling it from the bottom of the base.
5
Fasten the speaker cable to the base.
1
Press the speaker cable and thread between the hooks.
2
Fit the speaker cable into the base cover groove as far as
possible.
Wall
RQT7384
Preventing the speakers from falling over
Attach screw eyes (not included) to secure the speakers to a wall
(diagram on the right).
• Obtain the screws appropriate to the walls and pillars to which the they
are going to be fastened.
• Consult with a qualified housing contractor concerning the appropriate
procedure when attaching to a concrete wall or a surface that may not
have strong enough support. Improper attachment may result in
damage to the wall or speakers.
5
SC-HT07EB-EN.fm
Page 6
Friday, May 7, 2004
4:29 PM
Speaker setup (for SC-HT07 and SC-HT05)
Setup and connections of speakers
Attach the stickers to the speaker cables.
3
xxx
2
xxx
1
xxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxx
4
xxx
3
xxx
5
SC-HT07
Front and surround
speakers
(The length of cables are
same.)
xxx
xxx
3
xxx
2
4
xxx
5
2
xxx
1
1
xxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
Step 1
4
xxx
xxxxxx
xxxxxx
xxx
Speaker setup (for SC-HT07 and SC-HT05)
5
xxx
About 10 cm
xxxxxx
1
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxxxxx
xxx
xxx
xxx
xxx
xxx
1
2
3
4
5
FRONT
Lch
FRONT
Lch
1
1
1
2
3
4
5
FRONT
Lch
1
FRONT
Lch
About 10 cm
1
2
Front speaker (L)
Front speaker (R)
Surround speaker (L)
Surround speaker (R)
Center speaker
SC-HT05
Use the long speaker cables for the
surround speakers(SB-PS725).
Place the speakers.
e.g., SC-HT07
Front
speaker (L)
Center speaker
SC-HT05
Front speaker (R)
Surround speakers
Subwoofer
Surround speaker
(L)
Surround
speaker (R)
Place on a shelf or
rack.
Placing the front, center, and surround
speakers at approximately the same
distance from the seating position.
The angles in the diagram are
approximate.
Positioning for best effect
How you set up your speakers can affect
the bass and the sound field.
Note the following points.
• Place speakers on flat secure bases.
• Place speakers too close to floors,
walls, and corners can result in
excessive bass. Cover walls and
windows with a thick curtain.
RQT7384
Front speakers (left right)
Place on the left and right of the TV at seated ear height so that there is good coherency between the
picture and sound.
Center speaker
Place underneath or above the center of the TV. Aim the speaker at the seating area.
Surround speakers (left right)
Place on the side of or slightly behind the seating area, higher than ear level.
Subwoofer
The subwoofer can be placed in any position as long as it is at a reasonable distance from the TV.
Note that some experimentation can yield the smoothest low frequency performance. Placement near a
corner can increase the apparent output level, but can result in unnatural bass.
6
If irregular coloring occurs on your television
The supplied speakers are designed to be used close to a
television, but the picture may be affected with some televisions
and setup combinations.
If this occurs, turn the television off for about 30 minutes.
The television's demagnetizing function should correct the
problem. If it persists, move the speakers further away from the
television.
Note
Keep your speakers
at least 10 mm away
from the system for
proper ventilation.
Caution
• The main unit and supplied speakers are only to be
used as indicated in this manual. Failure to do so may
lead to damage to the receiver and/or the speakers,
and may result in the risk or fire. Consult a qualified
service person if damage has occurred or if you
experience a sudden change in performance.
• Do not attempt to attach these speakers to walls using
methods other than those described in this manual.
Sticker sheet
1
xxxxxx
xxx
xxxxxx
xxx
xxxxxx
xxx
xxxxxx
xxx
3
3
xxxxxx
xxx
2
xxxxxx
xxx
1
xxxxxx
xxx
xxxxxx
xxx
4
xxxxxx
xxx
5
xxxxxx
xxx
4
4
2
xxxxxx
xxx
xxxxxx
xxx
3
xxxxxx
xxx
xxxxxx
xxx
2
xxxxxx
xxx
xxxxxx
xxx
1
xxxxxx
xxx
5
5
xxxxxx
xxx
1
SC-HT05 (4 m x 3) (10 m x 2)
3
2
SC-HT07 (4 m x 1)
3
Speaker cable(s)
xxxxxx
xxx
Supplied
accessories
4:29 PM
4
Friday, May 7, 2004
xxxxxx
xxx
Page 7
5
SC-HT07EB-EN.fm
( x 1)
Connect the speaker cables to the subwoofer.
Subwoofer
SC-HT07
Speaker setup (for SC-HT07 and SC-HT05)
Step 1
Copper
Silver
SC-HT05
Copper
Silver
FRONT (L)
FRONT (R)
4
1
FRONT
(6 Ω)
2
SURROUND CENTER
(6 Ω)
(6 Ω)
Copper
Silver
3
5
2
1
4
3
R
L
R
L
SURROUND
(R)
SURROUND
(L)
Note
CENTER
Never short-circuit positive (+)
and negative (–) speaker wires.
5
Other speaker setup options
Fitting optional speaker stands
Attaching to a wall
SC-HT05
SC-HT07
SC-HT05 5 mm, Pitch 0.8 mm
60 mm
150 mm
230 mm
30 - 35 mm
7.5 -9.5 mm
Speaker
stands (not
included)
Wall or pillar
Plate thickness +7 to 10 mm
8 - 11 mm
• The wall or pillar on which the speakers are to be attached should be capable of
supporting 10 kg per screw. Consult a qualified building contractor when attaching
the speakers to wall. Improper attachment may result in damage to the wall and
speakers.
• (SC-HT07) When mounting the front and surround speakers to walls, use a string
(not included) to prevent them from a falling (è page 5). Use of optional speaker
cables are recommended for wall mounted front and surround speakers. (You can
also remove the speaker cables from the pipes supplied with this system).
• Observe the diameter and length of the
screws and the distance between screws
as shown in the diagram.
• The stands must be able to support over
10 kg.
• The stands must be stable even if the
speakers are in a high position.
RQT7384
Screw (not included)
7
SC-HT07EB-EN.fm
Step
Page 8
Friday, May 7, 2004
2
4:29 PM
Home theater connections
Other
accessories
Stereo phono cable
(not included)
Video connection cable
(not included)
Left
Right
Changing the digital input settings
You can change the input settings for the digital terminals if
necessary. Note the equipment you have connected to the
terminals, then change the settings (è page 22).
Turn off all components before making any connections.
To connect equipment, refer to the appropriate operating
instructions.
Note
Home theater connections
Step 2
The included AC mains lead is for use with this unit only.
Do not use it with other equipment.
TV (Monitor)
VIDEO
IN
Subwoofer
FOR THE UNITED KINGDOM ONLY
READ THE CAUTION FOR THE AC MAINS LEAD
ON PAGE 2 BEFORE CONNECTION.
AC mains lead (included)
Connect this cord after all other cables are connected.
è To household AC mains socket
75 Ω
LOOP ANT
GND
LOOP EXT
CD
L
FM ANT
TAPE
DVR / VCR1
L
L
R
R
TV
L
DVD / DVD 6CH
L
L
R
R
CENTER
TV
MONITOR OUT
IN
AM ANT
TO SB-WA07
R
AC IN ~
A
IN
REC(OUT) PLAY(IN)
R
OUT
IN
AUDIO
IN
FRONT SURROUND SUBWOOFER
OUT
IN
DVR / VCR1
VIDEO
System cable (included)
To disconnect
Press the catch and pull out.
RQT7384
Catch
8
FRONT
(L, R)
DVD player
SURROUND
(L, R)
SUBWOOFER
AUDIO OUT
CENTER
VIDEO
OUT
IN
DVD
Friday, May 7, 2004
4:29 PM
System cable
Supplied
accessories
AC mains lead
or
(x 1)
Remote control transmitter
or
(x 1)
Batteries
(x 1)
(x 2)
The remote control
Note
• Use digital connection to enjoy Dolby Digital or DTS.
1
Notes on digital input
This unit can decode the following signals:
• Dolby Digital, DTS
• PCM, including PCM with sampling frequencies of 96
or 88.2 kHz
It cannot decode:
• Other digital signals, such as MPEG
• Dolby Digital RF signals from a laser disc player
3
R6/LR6, AA, UM-3
2
2
• Insert so the poles (+ and –) match those in the remote
control.
• Do not use rechargeable type batteries.
(For continental Europe and the
United Kingdom)
21-pin scart cable (not included)
AV1 (TV OUT):
Connect to the 21-pin scart (IN) terminal on a television if
you have connected equipment to AV2 (DVD IN) or AV3
(DVR/VCR1 IN). This unit must be on to output audio/video
signals to the television.
AV2 (DVD IN):
Connect to the 21-pin scart (OUT) terminal on a DVD player.
Change the AV output setting for DVD to “SCART” (è page 22).
AV3 (DVR/VCR1 IN):
Connect to the 21-pin scart (OUT) terminal on a DVD
recorder or VCR. Change the AV output setting for VCR to
“SCART” (è page 22). For Q Link* to work, connect to this
terminal.
Use
Step 2
Page 9
Aim at the sensor, avoiding obstacles, at a maximum range of
7 m directly in front of the unit.
Remote control signal sensor
TOP MENU
VOLUME
MULTI CONTROL
PREV /
ENTER
INPUT SELECTOR
VIDEO IN
MUSIC
AV/MOVE
NEXT /
DOWN
SFC
^
8
TUNE
UP
TUNE
L AUDIO IN R VCR 2
RETURN
PHONES
7 meters
Home theater connections
SC-HT07EB-EN.fm
Transmission window
AV1 (TV OUT)
(TV) IN
OPT 1
AV2 (DVD IN)
(DVR) IN (DVD) IN
OPT 2 COAXIAL
DIGITAL IN
AV3 (DVR/VCR1 IN)
Note
Coaxial cable (not included)
Used to connect to the DIGITAL COAXIAL OUT terminal
on a DVD player to input audio digital signals.
SC-HT07 (For areas other than continental Europe and the
United Kingdom)
S-Video cable (not included)
S-VIDEO
IN
IN
DVR / VCR1
IN
DVD
DVD
player
Appliance inlet
Connector
Used to connect to the
S-VIDEO OUT terminal
on a DVD player.
TV or
monitor
Used to connect to the S-VIDEO IN terminal on a television.
S-VIDEO
IN
Insertion of connector
Even when the connector is perfectly inserted, depending on the type
of inlet used, the front part of the connector may jut out as shown in
the drawing.
However there is no problem using the unit.
* Q Link (registered trademark of Panasonic)
DATA LOGIC (registered trademark of Metz)
Easy Link (registered trademark of Philips)
Megalogic (registered trademark of Grundig)
SMARTLINK (registered trademark of Sony)
Approx. 6 mm
Power plug adapter (included) (For areas other than continental
Europe, the United Kingdom, Australia, and New Zealand)
If the power plug does not fit your socket, use this adapter.
RQT7384
MONITOR OUT
TV
S-VIDEO
OUT
• Keep the transmission window and the unit’s sensor free from
dust.
• Operation can be affected by strong light sources, such as
direct sunlight, and the glass doors on cabinets.
9
SC-HT07EB-EN.fm
Step
Page 10
Friday, May 7, 2004
3
4:29 PM
Other connections
Antennas
FM indoor antenna
(included)
For best reception
AM loop antenna
(included)
Adhesive tape
Fix the other end of the
antenna where reception
is best.
White
Red
FM outdoor antenna (not included)
• Disconnect the FM indoor antenna.
• The antenna should be installed by a
competent technician.
Click!
FM outdoor antenna
Black
75 Ω
75 Ω
LOOP ANT
GND
LOOP EXT
CD
TAPE
Step 3
L
FM ANT
AM ANT
TO SB-WA07
L
R
R
DVD / DVD 6CH
L
L
TV
CENTER
MONITOR OUT
FM ANT
AM
IN
ANT
75 Ω coaxial cable
LOOP ANT
GND
R
REC(OUT) PLAY(IN)
3
IN
A
TV
L
2
1
R
Other connections
DVR / VCR1
L
LOOP EXT
OUT
IN
AUDIO
R
IN
R
FRONT SURROUND SUBWOOFER
For United Kingdom
Antenna plug adaptor
(included)
2
OUT
IN
DVR / VCR1
VIDEO
75 Ω
IN
DVD
FM ANT
1
Keep the antenna cord away from DVD players and other cords.
DVD recorder or VCR
• Do not bend the optical fiber cable.
75 Ω
LOOP ANT
GND
LOOP EXT
CD
L
FM ANT
DVR / VCR1
TAPE
L
L
R
R
TV
L
DVD / DVD 6CH
L
L
R
R
TV
CENTER
MONITOR OUT
IN
AV1 (TV OUT)
AV2 (DVD IN)
AM ANT
TO SB-WA07
R
A
IN
REC(OUT) PLAY(IN)
R
OUT
IN
AUDIO
IN
FRONT SURROUND SUBWOOFER
OUT
IN
DVR / VCR1
VIDEO
RQT7384
(DVR) IN (DVD) IN
OPT 2 COAXIAL
DIGITAL IN
AUDIO OUT
VIDEO OUT
AUDIO IN
VIDEO IN
AV3 (DVR/VCR1 IN)
(For areas other than continental Europe and
SC-HT07 the United Kingdom)
S-Video cable (not included)
S-VIDEO
10
(TV) IN
OPT 1
Video connection
cables
(not included)
Stereo phono
cables
(not included)
DVD recorder or
VCR
IN
DVD
MONITOR OUT
TV
IN
IN
DVR / VCR1
IN
DVD
S-VIDEO
OUT
Used to connect to the
S-VIDEO OUT terminal on a
DVD recorder or VCR.
Optical fiber cable (not
included)
Used to connect to the
DIGITAL OPTICAL OUT
terminal on a DVD recorder to
input audio digital signals.
SC-HT07EB-EN.fm
Page 11
Friday, May 7, 2004
Supplied
accessories
4:29 PM
FM indoor antenna
AM loop antenna
Antenna plug adapter
(x 1)
(x 1)
(x 1)
For United
Kingdom
TV (Input source)
• Do not bend the optical fiber cable.
CD
TAPE
L
L
L
R
R
L
DVD / DVD 6CH
L
L
R
R
CENTER
Optical fiber cable (not
included)
AV2 (DVDUsed
IN)
to connect to the DIGITAL
OPTICAL OUT terminal on a
television
to input audio digital
AV3 (DVR/VCR1
IN)
signals.
TV
MONITOR OUT
IN
AV1 (TV OUT)
AM ANT
TO SB-WA07
R
IN
A
REC(OUT) PLAY(IN)
R
OUT
IN
AUDIO
IN
FRONT SURROUND SUBWOOFER
OUT
IN
DVR / VCR1
VIDEO
IN
DVD
Stereo phono cable
(not included)
(TV) IN
OPT 1
(DVR) IN (DVD) IN
OPT 2 COAXIAL
DIGITAL IN
Video
connection
cables
(not included)
(For areas other than continental
SC-HT07 Europe and the United Kingdom)
S-Video cable (not included)
S-VIDEO
TV
MONITOR OUT
TV
AUDIO
OUT
IN
IN
DVR / VCR1
Used to connect to
the S-VIDEO OUT
S-VIDEO
terminal on a
OUT
television.
IN
DVD
VIDEO OUT
VIDEO IN
SC-HT07
SC-HT07
Cassette deck
75 Ω
LOOP ANT
GND
LOOP EXT
TAPE
CD
L
FM ANT
DVR / VCR1
L
L
R
R
TV
L
DVD / DVD 6CH
L
L
R
R
CENTER
TV
MONITOR OUT
IN
AV1 (TV OUT)
AV2 (DVD IN)
AM ANT
Other connections
FM ANT
TV
DVR / VCR1
TO SB-WA07
R
IN
A
REC(OUT) PLAY(IN)
R
OUT
IN
AUDIO
IN
FRONT SURROUND SUBWOOFER
Stereo phono cables
(not included)
OUT
IN
DVR / VCR1
VIDEO
IN
DVD
(TV) IN
OPT 1
(DVR) IN (DVD) IN
OPT 2 COAXIAL
DIGITAL IN
PLAY (OUT)
AV3 (DVR/VCR1 IN)
Cassette deck
REC (IN)
CD player
75 Ω
LOOP EXT
SC-HT07
SC-HT07
LOOP ANT
GND
CD
L
FM ANT
TAPE
DVR / VCR1
L
L
R
R
TV
L
DVD / DVD 6CH
L
L
R
R
CENTER
TV
MONITOR OUT
IN
AM ANT
TO SB-WA07
R
A
IN
REC(OUT) PLAY(IN)
R
OUT
IN
AUDIO
Stereo phono
cable
(not included)
IN
FRONT SURROUND SUBWOOFER
OUT
IN
DVR / VCR1
VIDEO
IN
DVD
Optical fiber cable or coaxial (not
included)
AV1 (TV OUT)
AV2 (DVD IN)
Used to connect
to the DIGITAL OUT terminal
on a CD player to input audio digital signals.
(TV) IN (DVR) IN (DVD) IN
AV3 (DVR/VCR1
IN)
(D-INPUT
setting
è page 22)
OPT 1 OPT 2 COAXIAL
DIGITAL IN
CD player
AUDIO OUT
Game machine or other AV equipment
75 Ω
LOOP EXT
LOOP ANT
GND
GAME/AUX
DVR / VCR
TV
DVD / DVD 6CH
CENTER
FM ANT
AM ANT
TO SB-WA05
A
Step 3
LOOP ANT
GND
LOOP EXT
TV
MONITOR OUT
SC-HT05
SC-HT07
GAME/AUX
IN
IN
AV1 (TV OUT)
L
AV2 (DVD IN)
R
IN
OUT
IN
IN
AUDIO
FRONT SURROUND SUBWOOFER
Stereo phono cable
(not included)
AUDIO OUT
OUT
IN
DVR / VCR
VIDEO
IN
DVD
(TV) IN
OPT 1
(DVR) IN (DVD) IN
OPT 2 COAXIAL
DIGITAL IN
AV3 (DVR/VCR IN)
Video connection cable
(not included)
VIDEO OUT
Game machine
RQT7384
75 Ω
11
SC-HT07EB-EN.fm
Step
Page 12
4
Friday, May 7, 2004
4:29 PM
Settings
Adjusting speaker output level
RECEIVER AV SYSTEM
^
^
DVD
DVD
DVD RECORDER
DVD/HDD RECORDER
VCR
1
2
3
4
5
6
7
TV
ANALOG 6CH
8
CD
CH
VOLUME
9
DIRECT TUNING
-/--
DISC
0
> 10
u/t
y/i
TUNER/BAND
=
MUTING
q
h
g
TOP MENU
MENU
PLAY
LIST
DIRECT
NAVIGATOR
ENTER
DISPLAY
RETURN
TV VOL
TV/AV
TV VOL
DIMMER SUBWOOFER
CENTER
FOCUS
INPUT
MODE
TEST
/L
/R
TONE/
BALANCE
SLEEP
LEVEL
EFFECT
STEREO/
2CH MIX
%PL
MUSIC
SFC
AV/MOVIE
Step 4
OFF
1
2
Settings
RECEIVER
^
Switch on.
3
4
5
6
VOLUME
TEST
Output the
signal.
LEVEL
Adjust the
main
volume.
Select the
speaker
channel.
/L
/R
Adjust the
level.
TEST
Stop the test
signal.
Repeat steps 4
and 5
C (center), RS (right surround) and LS (left surround) can be adjusted between –10 dB and +10 dB, with 0 dB being the level of
the front speakers. Adjust center and surround output to the same apparent level of the front speakers.
For SW (subwoofer), you can select “- - -” so there is no output, “MIN” for minimum output, a level between 1 and 19, or “MAX” for
maximum output. Adjust subwoofer output so it is balanced with the front speakers.
Subwoofer output is easily influenced by the source. You can also change its level while playing something for better effect
RQT7384
(è page 20).
12
SC-HT07EB-EN.fm
Page 13
Friday, May 7, 2004
4:29 PM
Basic operations
NAVIGATOR
ENTER
TOP MENU
ENTER
PREV /
INPUT SELECTOR
MUSIC
VIDEO IN
1
RETURN
TV VOL
NEXT /
TV VOL
SFC
^
8
DISPLAY
VOLUME
MULTI CONTROL
AV/MOVE
TUNE
L AUDIO IN R
VCR 2
^
8
Switch on.
TV/AV
TUNE
RETURN
2
3
INPUT SELECTOR
4
Start play of the
source.
SC-HT07
TUNER CD
The unit sets the
sound mode to suit
the input signal.
TV
TAPE VCR2 DVR/VCR1
SC-HT05
TUNER
DVD
TV
GAME/AUX
CENTER
FOCUS
INPUT
MODE
TEST
/L
/R
TONE/
BALANCE
SLEEP
LEVEL
EFFECT
STEREO/
2CH MIX
%PL
MUSIC
SFC
AV/MOVIE
OFF
VOLUME
Select input.
DVD
UP PHONES
DOWN
DIMMER SUBWOOFER
SFC
MUSIC AV/MOVIE
DOWN
UP
%PL
Adjust the
volume.
DVR/VCR
STEREO/
2CH MIX
OFF
Sound modes
MOVIE
Use this mode when playing movie software, especially videotapes,
recorded in Dolby Surround.
Adding surround effects to stereo
sources
Dolby Pro Logic II and SFC modes remain in
effect until you change them.
• To cancel
Press [STEREO/2CH MIX, OFF].
Listening to multi-channel sources in
stereo
When surround sources are played in this
mode, the sounds intended for the other
speaker channels are played through the front
speakers.
The 2CH MIX mode remains in effect until you
change input mode or turn off the unit.
• To return to surround sound
Press [STEREO/2CH MIX, OFF].
MUSIC
Adds surround effects to stereo sources.
PANORAMA
Sound is spread out more so you feel like you are surrounded by music.
LIVE
Brings you up close for “live” stage performance and smoother vocals.
POP/ROCK
For pop, rock, and other music that has a punch to it.
MUSIC
AV/MOVIE
VOCAL
For adding gloss to vocals.
JAZZ
Conveys the exciting and intimate atmosphere of a jazz club.
DANCE
For dance music and other sounds with a strong beat.
PARTY
This mode uses the front and surround speakers so that sound is in
stereo regardless of the direction you are facing.
Operations
Using the Sound Field Control (SFC)
Enjoy an enhanced sound experience with
greater presence and spread by using these
SFC modes with PCM or analog stereo
sources.
Choose from the following modes.
You can adjust SFC effects. (è page 21)
%PL
DRAMA
For dramas and other material where dialog is important.
ACTION
For action movies and other material where impact is important.
SPORTS
To make you feel like you were in the stadium.
MUSICAL
For musicals and other material where music is important.
GAME
Enjoy gaming with more impact.
MONO
For monaural sound.
Note
• When input is PCM with sampling frequencies of 96 or 88.2 kHz, you
cannot add surround effects with Dolby Pro Logic II or SFC.
• When input is Dolby Digital or DTS, you cannot use SFC.
RQT7384
Using Dolby Pro Logic II
Dolby Pro Logic II processor works not only on
sources recorded with Dolby Surround, but also
on any stereo source.
The following modes are available when using
Dolby Pro Logic II.
You can make fine surround settings when in
the MUSIC or PANORAMA mode. (è page 20)
13
SC-HT07EB-EN.fm
Page 14
Friday, May 7, 2004
4:29 PM
Control guide
Main unit
[SFC, MUSIC, AV/MOVIE]
For selecting SFC modes.
[INPUT SELECTOR]
For selecting input.
Standby indicator [^]
When the unit is connected to the AC mains supply, this
indicator lights up in standby mode and goes out when the
unit is turned on.
Standby/on switch [8]
Press to switch the unit from on to standby mode or vice
versa.
In standby mode, the unit is still consuming a small amount
of power.
SFC
^
8
INPUT SELECTOR
VIDEO IN
MUSIC
AV/MOVE
TUNE
L AUDIO IN R
VCR 2
TUNE
Remote control signal sensor
SC-HT07
[VCR 2]
Connect equipment like video cameras.
[TUNE2, TUNE1]
For tuning the radio and selecting preset stations.
Display
Operations
[DIGITAL INPUT]
Program format indicators
Show the channels contained in the digital
input signal.
They do not light when input is analog.
L: Front left channel
C: Center channel
R: Front right channel
LS: Surround left channel
S: If the surround channel is monaural
RS: Surround right channel
LFE (Low Frequency Effects): Deep-bass
effect
[TUNED, M, MONO, ST ]
Radio indicators
TUNED: A station is tuned.
M: Flashes or lights during presetting.
MONO: You have switched to monaural mode with [FM
MODE] to improve reception.
ST: A stereo FM broadcast is tuned.
DIGITAL INPUT
L C R
LS
TUNED M RDS
MONO ST PS PTY
S RS LFE
%DIGITAL
%PRO LOGIC
C.FOCUS
SLEEP
2CH MIX 100Hz
SURROUND
SFC
1kHz
10kHz
kHz
MHz
[%DIGITAL, dts, %PRO LOGIC II]
Light to indicate the source’s input signal and
decoding format used.
[kHz, MHz]
General display
RQT7384
Shows the input mode, radio frequency, and
other general information.
14
[RDS, PS, PTY]
(For continental Europe and the
United Kingdom)
Shows the current RDS display
mode.
Frequency unit indicators
kHz: AM, or PCM sampling
frequency
MHz: FM
SC-HT07EB-EN.fm
Page 15
Friday, May 7, 2004
4:29 PM
[MULTI CONTROL]
For presetting radio stations and various other settings.
(è page 17)
[VOLUME]
Volume control.
[PHONES]
TOP MENU
VOLUME
MULTI CONTROL
PREV /
ENTER
RETURN
Headphone jack
Plug type: 3.5 mm stereo
• Sound does not come from the speakers if you connect
headphones.
• Avoid listening for prolonged periods of time to prevent
hearing damage.
NEXT /
DOWN
UP PHONES
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories.
Operations
“DTS” and “DTS Digital Surround” are registered trademarks
of Digital Theater Systems, Inc.
[C.FOCUS]
Appears when you are using Center Focus
[SLEEP]
Sleep timer indicator.
Spectrum analyzer display
2CH MIX: Appears when you are playing a
multi-channel source in 2CH MIX mode
SURROUND: Appears when you are playing
through multiple channels
SFC: Appears when you are using an SFC
mode
For your reference
• If you have used scart connections, depending on the features
of your television and other equipment, television input may
automatically switch input when you start play.
• When playing sources connected to the DVD IN RCA
terminal
The picture remains on the screen even if you select an audio
source.
RQT7384
[2CH MIX, SURROUND, SFC]
15
SC-HT07EB-EN.fm
Page 16
Friday, May 7, 2004
4:29 PM
Control guide
Remote control
This page describes the buttons used to control this unit.
See the guide starting page 23 for the buttons that control other unit’s.
[^, RECEIVER]
SC-HT07
Standby/on button.
[DVD, -ANALOG 6CH] [TV]
[DVD RECORDER] [VCR] [CD]
[1, 2, 3, 4, 5, 6, 7, 8, 9, 0]
SC-HT05
To enter radio frequencies and channels.
RECEIVER AV SYSTEM
^
[ ≧ 10, -/--]
To enter two digit channels.
DVD
^
To enable selection of radio stations
by frequency.
[TUNER/BAND]
For switching between FM and AM.
[1, CH, 2]
4
5
7
8
[DIMMER]
Input mode and remote control mode
buttons.
3
CH
6
VOLUME
9
DIRECT TUNING
For selecting preset radio channels.
VCR
2
1
CD
ANALOG 6CH
DVD
DVD RECORDER
DVD/HDD RECORDER
[DISC, DIRECT TUNING]
TV
[DVD, -ANALOG 6CH] [TV]
[DVD RECORDER] [VCR] [GAME/AUX]
-/--
DISC
0
> 10
u/t
y/i
TUNER/BAND
=
[+, –, VOLUME]
MUTING
g
q
h
TOP MENU
MENU
To mute the volume.
For selecting AUTO, ANALOG or
DIGITAL.
DIRECT
NAVIGATOR
PLAY
LIST
[SUBWOOFER]
For selecting subwoofer level.
[TEST]
[STEREO/2CH MIX, OFF]
For selecting STEREO or 2CH MIX
mode.
To cancel surround effect.
DISPLAY
RETURN
TV VOL
TV VOL
TV/AV
[%PL II]
For selecting a Dolby Pro Logic II
mode: MOVIE, MUSIC or
PANORAMA.
[MUSIC]
DIMMER SUBWOOFER
CENTER
FOCUS
INPUT
MODE
TEST
/L
/R
TONE/
BALANCE
SLEEP
LEVEL
EFFECT
STEREO/
2CH MIX
For selecting SFC modes: LIVE, POP/
ROCK, VOCAL, JAZZ, DANCE or
PARTY.
MUSIC
%PL
SFC
AV/MOVIE
1, 2, 3, 4, 5, 6, 7, 8, 9 ,0, >=10
DISC, DIRECT TUNING
RECEIVER AV SYSTEM
^
^
SUBWOOFER
1
2
4
5
7
8
TV
GAME/AUX
CH
6
VOLUME
9
DIRECT TUNING
-/--
DISC
0
> 10
u
i
t
y
h
q
TOP MENU
MENU
DIRECT
NAVIGATOR
PLAY
LIST
ENTER
DISPLAY
RETURN
TV VOL
DIMMER
INPUT
MODE
TEST
OFF
DVD RECORDER
TEST
,
TV VOL
MUTING
STEREO/
2CH MIX
DVD, -ANALOG 6 CH
TV
GAME/AUX
VCR
1, CH, 2
, , VOLUME
=
CENTER
%PL
VCR
3
SUBWOOFER FOCUS
CENTER FOCUS
STEREO/2CH MIX, OFF
DVD
ANALOG 6CH
DVD
TUNER/BAND RECORDER
g
DIMMER
MUTING
INPUT MODE
[LEVEL]
Use when adjusting speaker level.
[EFFECT]
Use when adjusting Dolby Pro Logic II
or SFC effects.
For selecting center focus mode.
To start the sleep timer.
^
To adjust the bass, treble and front
speaker balance.
[CENTER FOCUS]
[SLEEP] SC-HT07
^, RECEIVER
TUNER/BAND
[TONE/BALANCE] SC-HT07
First select SLEEP, EFFECT, LEVEL,
TONE or BALANCE, then press [–/L]
or [+/R] to adjust.
For selecting SFC modes: DRAMA,
ACTION, SPORTS, MUSICAL, GAME
or MONO.
SC-HT05
To start the speaker test signal.
[–/L, +/R] (–, +)
OFF
[AV/MOVIE]
Operations
[MUTING]
[INPUT MODE]
ENTER
RQT7384
To adjust the volume.
SLOW
For dimming the unit's display
16
[DVD, -ANALOG 6CH]
Press and hold and DVD input
switches between 6-channel and
2-channel.
%PL
TV/AV
DVD RECORDER
DVD/HDD
LEVEL
MUSIC
EFFECT
SFC
AV/MOVIE
LEVEL
EFFECT
AV/MOVIE
MUSIC
SC-HT07EB-EN.fm
Page 17
Friday, May 7, 2004
4:29 PM
MULTI CONTROL operations
This is an outline of the operations you can perform with the MULTI CONTROL.
See pages 18, 19, 21 and 22 for details.
TOP MENU
MULTI CONTROL
PREV /
ENTER
NEXT /
TOP MENU
1
or
ENTER
RETURN
3
Sub menu (Level 1)
ENTER
(Level 2)
(Level 3)
ENTER
ENTER
Tuning mode
ENTER
MANUAL PRESET
TUNER
TUNING
Tuner
(Only when input is TUNER)
FM MODE
FM mode
AUTO
MEMORY
Memory
CH1
AUTO MEM
Auto memory
START
DISPLAY
RDS display1)
FREQ
RDS PS RDS PTY
9 kHz
10 kHz
AM ALLOC
TONE
BASS
Tone
BALANCE
Balance
DIMMER
Dimmer
SLEEP
Sleep timer
OPTION
Option
L
AM allocations
TREBLE
R
L
CH30
10dB
R
L
0dB
10dB
R
OFF
ON
OFF
DR COMP
A/D ATT
SPECTRUM
LEVEL1
30
60
Dynamic range
compression
A/D attenuator
Spectrum display
DTS-PCM
SETUP
MONO
D-INPUT
Digital input
AV OUT
AV output
RESET
Reset
LEVEL2
90
120
OFF
STANDARD
OFF
ON
ON
OFF
OFF
ON
CD
TV
1)
DVR
MAX
NONE
OPT1
DVD
OPT2
COAX
DVD
VCR
RCA
SCART
NO
YES
(SC-HT07)
Setup
LEVEL3
(SC-HT07)
Operations
2 Main menu
To exit
EXIT
For continental Europe and the United Kingdom
Note
• You can adjust the level of the bass and treble. The STEREO mode must be on and input must be either analog or PCM signals.
You cannot adjust the tone if DVD ANALOG 6CH is selected.
• Setting is impossible if the selected menu does not appear.
RQT7384
1)
• Press [RETURN] to return to the level above. Be noted that this will cancel your setting.
• Press [TOP MENU] to return to the Top menu.
• Pressing [RETURN] or [TOP MENU] while the Top menu is displayed takes you immediately to EXIT.
17
SC-HT07EB-EN.fm
Page 18
Friday, May 7, 2004
4:29 PM
The radio
SC-HT05
RECEIVER AV SYSTEM
^
^
DVD
ANALOG 6CH
DVD
TUNER/BAND RECORDER
VCR
1
2
3
4
5
6
7
TV
8
9
DIRECT TUNING
-/--
DISC
0
> 10
u
i
t
GAME/AUX
CH
VOLUME
g
h
y
q
DIRECT
NAVIGATOR
^
TV VOL
MUTING
DIMMER
TV/AV
VCR
2
3
4
5
6
7
8
9
-/--
DISC
0
> 10
y/i
TUNER/BAND
g
TOP MENU
PLAY
LIST
DIRECT
NAVIGATOR
CH
CH
VOLUME
DISPLAY
TV VOL
TV VOL
DVD RECORDER
DVD/HDD
TV/AV
ENTER
NEXT /
TOP MENU
VOLUME
MULTI CONTROL
DISC
PREV /
ENTER
NEXT /
SFC
^
INPUT SELECTOR
VIDEO IN
=
h
TOP MENU
RETURN
DIRECT TUNING
MUSIC
AV/MOVE
TUNE
L AUDIO IN R
VCR 2
TUNE
RETURN
DOWN
UP PHONES
MUTING
q
MENU
PLAY
LIST
ENTER
RETURN
PREV /
CD
8
u/t
MENU
MULTI CONTROL
TV
ANALOG 6CH
1
ENTER
DISPLAY
^
DVD
DVD
DVD RECORDER
DVD/HDD RECORDER
DIRECT TUNING
=
TOP MENU
SC-HT07
RECEIVER AV SYSTEM
1
2
TUNER/BAND
TUNER/BAND
Select “FM” or
“AM“.
TUNE
TUNE
Select the frequency.
Auto tuning starts if you press and hold the button.
RETURN
TV VOL
DIMMER SUBWOOFER
CENTER
FOCUS
Direct tuning
Input the frequency of the station.
Remote control
1. Press [TUNER/BAND] to select “FM” or “AM”.
2. Press [DISC, DIRECT TUNING].
3. Press the numbered buttons to enter the frequency.
e.g. To select 107.90 MHz, press [1] → [0] → [7] → [9] → [0]
• If you do not press a button while the cursor is flashing, the
display returns to the frequency being received.
• If the frequency has not been input correctly, “ERROR” will be
displayed.
FM mode
You can improve FM reception by switching reception to
monaural.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “TUNER”.
è [ENTER]
3. Press [< , >] to select “FM MODE”.
è [ENTER]
4. Press [< , >] to select “MONO”.
è [ENTER]
Manual presetting
Preset the stations one at a time.
Preparation: Tune to the station you want to preset.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “TUNER”.
è [ENTER]
3. Press [< , >] to select “MEMORY”.
è [ENTER]
4. Press [< , >] to select a channel.
è [ENTER] (“STORED” lights.)
For your reference
FM stations can also be preset in the MONO mode.
Selecting channels
Remote control
Press [2, CH, 1].
or
Press the numbered buttons.
For channels 1 to 9, press the corresponding number.
For channels 10 or over, press [ ≧ 10, -/--], then the two digits.
e.g. To select channel 21: [ ≧ 10, -/--] → [2] → [1]
Operations
Select “AUTO” to cancel.
Automatic presetting
The FM stations the unit can receive are preset in channels 1 to 30.
The AM stations the unit can receive are preset in channels 21 to
30. (FM stations are replaced if any were preset in these channels.)
Preparation: Tune to either FM 87.50 MHz or AM 522 kHz.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “TUNER”.
è [ENTER]
3. Press [< , >] to select “AUTO MEM”.
è [ENTER] (“START” lights.) è [ENTER]
On the main unit
Switch the tuning mode to “PRESET”.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “TUNER”.
è [ENTER] (“TUNING” lights.) è [ENTER]
3. Press [< , >] to select “PRESET”.
è [ENTER]
Select “MANUAL” to cancel.
Main unit
4. Press [TUNE2, TUNE1] to select a channel.
RQT7384
During automatic presetting, the memory indicator (M) flashes
and the frequency scrolls. The memory indicator and channel
numbers are displayed for a second when a station is preset.
The last station to be preset is displayed when presetting
finishes.
For your reference
Even if the AC mains lead is disconnected from the household AC mains outlet, the stations remain in memory for approximately two
18 weeks.
SC-HT07EB-EN.fm
Page 19
Friday, May 7, 2004
4:29 PM
Other functions
MULTI CONTROL
RDS broadcasts
TOP MENU
PREV /
(For continental Europe and the United Kingdom)
Note
This unit does not have the emergency broadcast system (EBS)
that tunes automatically into emergency broadcasts.
PTY Displays
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M. O. R. M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL A
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATIONAL
OLDIES
FOLK M
DOCUMENT
TEST
ALARM
News
Current affairs
Information
Sport
Education
Drama
Culture
Science
Varied
Pop music
Rock music
Middle-of-the-road Music
Light classical
Serious classical
Other music
Weather information
Finance
Children
Social affairs
Religion
Phone in
Travel
Leisure
Jazz music
Country music
National music
Oldies
Folk music
Documentary
Test broadcast
Emergency announcement
To change the AM frequency step
(For continental Europe and the United Kingdom)
MULTI CONTROL
1.
2.
3.
4.
Press [TOP MENU].
Press [< , >] to select “TUNER” è [ENTER]
Press [< , >] to select “AM ALLOC” è [ENTER]
Press [< , >] to select “9” or “10” è [ENTER]
(The frequency step changes from 9 kHz to 10 kHz.).
MENU
TOP
MENU
TOP
VOLUME
MULTI
CONTROL
MULTICONTROL
PREV
/ /
PREV
UNE
TUNE
ENTER
ENTER
NEXT //
NEXT
RETURN
CR 2
RETURN
DOWN
UP PHONES
Dynamic range compression
Change this setting to listen to software recorded with Dolby
Digital at low volume (such as late at night) and maintain audio
clarity. It reduces the peak level in loud scenes without affecting
the sound field.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “OPTION”.
è [ENTER] (“DR COMP” lights.)
è [ENTER]
3. Press [< , >] to select “OFF”, “STANDARD” or
“MAX”.
è [ENTER]
OFF: The software is played with the original dynamic range
(factory setting).
STANDARD: The level recommended by the producer of the
software for household viewing.
MAX: The maximum allowable compression (recommended for
night viewing).
A/D attenuator
Turn the A/D attenuator on if “OVERFLOW” lights frequently
when using 2-channel analog input.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “OPTION”.
è [ENTER]
3. Press [< , >] to select “A/D ATT”.
è [ENTER]
4. Press [< , >] to select “ON” or “OFF”.
è [ENTER]
Operations
RDS PS: program service, the station name
RDS PTY: program type
FREQ: Frequency display
RETURN
Spectrum display
Switch the SPECTRUM display on or off.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “OPTION”.
è [ENTER]
3. Press [< , >] to select “SPECTRUM”.
è [ENTER]
4. Press [< , >] to select “ON” or “OFF”.
è [ENTER]
RQT7384
1. Press [TOP MENU].
2. Press [< , >] to select “TUNER”.
è [ENTER]
3. Press [< , >] to select “DISPLAY”.
è [ENTER]
4. Press [< , >] to select “RDS PS”, “RDS PTY”, or
“FREQ”.
è [ENTER]
NEXT /
ENTER
This unit can display the text data transmitted by the radio data
system (RDS) available in some areas.
“RDS” lights while RDS signals are being received.
RDS displays may not be available if reception is poor.
MULTI CONTROL
19
SC-HT07EB-EN.fm
Page 20
Friday, May 7, 2004
4:29 PM
Other functions
4
5
6
4
8
9
SC-HT07
-/--
7
DIRECT TUNING
DISC
0
> 10
u/t
y/i
TUNER/BAND
=
5
q
-/--
DISC
0
> 10
u
i
t
MENU
TOP MENU
DIRECT
NAVIGATOR
PLAY
LIST
DIRECT
NAVIGATOR
RETURN
TV VOL
CENTER
SUBWOOFER FOCUS
INPUT
MODE
TEST
TONE/
BALANCE
SLEEP
STEREO/
2CH MIX
%PL
OFF
q
MENU
PLAY
LIST
ENTER
DISPLAY
DIMMER
y
h
ENTER
TV/AV
VOLUME
=
g
TOP MENU
TV VOL
6
8
9
SC-HT05
7
DIRECT TUNING
MUTING
h
g
VOLUME
/L
LEVEL
MUSIC
/R
EFFECT
SFC
AV/MOVIE
DISPLAY
RETURN
TV VOL
TV VOL
MUTING DIMMER
INPUT
MODE
DVD RECORDER
DVD/HDD
TEST
CENTER
SUBWOOFER FOCUS
STEREO/
2CH MIX
TV/AV
%PL
LEVEL
MUSIC
EFFECT
“C.FOCUS” lights.
The factory setting is off.
The center focus cannot be used in the following case.
When input signal is PCM or analog stereo.
When DVD ANALOG 6CH is selected.
AV/MOVIE
1. Press [EFFECT] to select “C-WDTH”.
2. Press [–/L] or [+/R] to adjust the effect.
Dimension Control "DIMEN"
Operations
Press [CENTER FOCUS].
Subwoofer level
OFF
You can adjust the effect of MUSIC and PANORAMA with the
center width control.
This adjustment helps you realize a more natural sound image
when listening to music. Move sound out into the front speakers
to improve the overall front image, or add sound to the center
speaker to fix the center image.
You can choose a level between 0 (the center speaker is
dominant) and 7 (center sound is spread out).
The default level is 3.
Remote control
You can adjust the effect of MUSIC and PANORAMA with the
dimension control.
You can make up for differences in the output level of the front
and surround speakers.
You can choose a level between –3 and +3 — Increase the level
to move sound to the front speakers, decrease to move it to the
surround speakers.
The default is level 0.
Remote control
1. Press [EFFECT] to select “DIMEN”.
2. Press [–/L] or [+/R] to adjust the effect.
Muting
Remote control
Press [MUTING].
To cancel
Press [MUTING] again.
Muting is also canceled when the unit is turned off.
RQT7384
(This works on digital signals that have a center channel)
You can make the sound of the center speaker seem like it is
coming from within the television.
Remote control
SFC
Center Width Control "C-WDTH"
20
Center focus
For selecting subwoofer level.
Remote control
Press [SUBWOOFER].
Adjust the level in 5 steps:
SW MIN, SW 5, SW 10, SW 15, and SW MAX.
Select "SW - - -" to stop output.
Note
Sound can be distorted if you raise the volume while subwoofer
level is high. Reduce subwoofer level if this occurs.
Input mode
This unit automatically detects whether input is digital or
analogue, but you can fix the input mode.
Remote control
Press [INPUT MODE] to select "AUTO", "ANALOG" or
"DIGITAL".
PCM/DTS fix mode
In rare cases, the unit may have trouble recognizing the digital
signals on discs.
• With the PCM signals on CDs, this may cause the beginning
of a track to be cut off. Engage the PCM FIX mode if this
occurs.
• With DTS, the signals may not be recognized at all. Engage
the DTS FIX mode if this occurs.
While the input source is selected:
Remote control
1. Press [INPUT MODE] to select “DIGITAL”.
2. Press and hold [INPUT MODE] for four seconds.
The current mode is displayed. Press again to change the mode.
Each time you press the button:
AUTO → PCM FIX → DTS FIX
When a FIX mode is on, the unit cannot process other signals.
This may cause noise to be output. Select “AUTO” if this occurs.
The mode returns to AUTO when you switch the unit to standby.
For your reference
If you are playing a DTS CD that contains both DTS and PCM,
but it isn’t playing properly, then do the following after step 1
above: Use the MULTI CONTROL to enter the “OPTION” –
“DTS-PCM” menu and select “ON”. If this causes noise to occur,
return the setting to “OFF”. (This setting is effective for each
digital source.)
SC-HT07EB-EN.fm
Page 21
Friday, May 7, 2004
4:29 PM
SLOW
g
MULTI CONTROL
SC-HT07
h
q
TOP MENU
MENU
DIRECT
NAVIGATOR
PLAY
LIST
DIRECT
NAVIGATOR
PLAY
LIST
DISPLAY
RETURN
DISPLAY
TV VOL
TV VOL
TV VOL
ENTER
NEXT /
ENTER
TV/AV
RETURN
TOP MENU
MENU
TOP
ENTER
CENTER
FOCUS
MUTING
RETURN
TV VOL
DIMMER
INPUT
MODE
DVD RECORDER
DVD/HDD
TV/AV
TEST
CENTER
SUBWOOFER FOCUS
LEVEL EFFECT
VOLUME
STEREO/
2CH MIX
NEXT /
NEXT /
%PL
MUSIC
SFC
AV/MOVIE
STEREO/
2CH MIX
%PL
MUSIC
SFC
AV/MOVIE
SFC
INPUT SELECTOR
VIDEO IN
MUSIC
AV/MOVE
TUNE
L AUDIO IN R
VCR 2
TUNE
RETURN
RETURN
OFF
DOWN
Tone
You can adjust the level of the bass and treble.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “TONE”.
è [ENTER]
3. Press [< , >] to select “BASS” or “TREBLE”.
è [ENTER]
4. Press [< , >] to adjust bass/treble.
è [ENTER]
Remote control (SC-HT07 only)
Press [TONE/BALANCE] to select “BASS” or “TREBLE”.
Press [–/L] or [+/R] to adjust bass/treble.
Note
The STEREO mode must be on and input must be either analog
or PCM signals.
Balance
You can adjust the balance of the front speakers.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “BALANCE”.
è [ENTER]
3. Press [< , >] to adjust.
è [ENTER]
Remote control (SC-HT07 only)
Press [TONE/BALANCE] to select “BALANCE”.
Press [–/L] or [+/R] to adjust.
OFF
UP PHONES
Sleep timer
The SLEEP timer can turn the unit off after a set time.
It does not control any other components.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “SLEEP”.
è [ENTER]
3. Press [< , >] to select the required time.
The display changes as follows:
OFF v 30 v 60 v 90 v 120 (minutes)
è
[ENTER]
Remote control (SC-HT07 only)
Press [SLEEP].
Press [–/L] or [+/R] to select the required time.
To check the setting
Repeat steps 1 and 2.
or
Press [SLEEP] on the remote control once. (SC-HT07 only)
The time remaining appears.
To change a setting
Repeat the procedure from the beginning.
Adjusting SFC effects
You can adjust the sound field by adjusting the level of the
speakers and the delay time of the surround speakers. These
adjustments can be made for each SFC mode.
To adjust the speaker level
1. Press [LEVEL] to select the speaker channel.
Operations
^
8
ENTER
DIMMERSUBWOOFER
INPUT
MULTI CONTROL
PREV /
ENTER
TEST
MODE
/L
/R
TONE/
BALANCE SLEEP LEVEL EFFECT
MULTI CONTROL
PREV /
SC-HT05
h
q
MENU
TOP MENU
PREV /
g
TOP MENU
Each time you press the button:
Dim the display for better viewing in a darkened room.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “DIMMER”.
è [ENTER]
3. Press [ < , >] to select “ON”.
è [ENTER]
4. Press [< , >] to select “LEVEL1”, “LEVEL2” or
“LEVEL3”.
è [ENTER]
Remote control
Press [DIMMER] to select dim or bright.
C →RS→ LS→ SW
2. Press [–/L] or [+/R] to adjust the level.
C, RS, and LS:–10 dB to +10 dB
SW:– – – (off) ↔ MIN ↔ 1 – 19 ↔ MAX
To adjust the delay time
1. Press [EFFECT].
2. Press [–/L] or [+/R] to change the delay time.
Delay time can be set at 10-millisecond (ms) intervals
between 10 and 100 ms.
The factory setting is 50 ms for each mode.
RQT7384
Dimmer
21
SC-HT07EB-EN.fm
Page 22
Friday, May 7, 2004
4:29 PM
Other functions
Using the VCR2 terminals
(for SC-HT07)
D-INPUT (Digital input)
SFC
INPUT SELECTOR
Change the setting for the DIGITAL IN terminals (OPT1, OPT2,
COAXIAL) on the rear of the unit if the equipment you have
connected is different to that labeled.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “SETUP”.
è [ENTER] (“D-INPUT” lights.) è [ENTER]
3. Press [< , >] to select “CD” (SC-HT07 only), “TV”,
“DVR” or “DVD”.
è [ENTER]
4. Press [< , >] to select “NONE” (SC-HT07 only),
“OPT1”, “OPT2” or “COAX”.
è [ENTER]
The factory settings are:
SC-HT07
CD:
TV:
DVR:
DVD:
NONE
OPT1
OPT2
COAX
MUSIC
VIDEO IN
AV/MOVE
TUNE
L AUDIO IN R
VCR 2
TUNE
AUDIO OUT
VIDEO OUT
Video camera
These terminals are convenient for equipment you want to
connect only temporarily. Select "VCR2" for input.
Making a recording
SC-HT05
TV:
OPT1
DVR: OPT2
DVD: COAX
INPUT SELECTOR
TOP MENU
MULTI CONTROL
Note
PREV /
You can allocate only one piece of equipment per terminal. So
for example if you change “TV” for “OPT1” to “OPT2”, “DVR” will
automatically switch to “OPT1”.
AV output
(For continental Europe and the United Kingdom)
Operations
Select the equipment (DVD player or DVD recorder/VCR) whose
audio/video signals you want to output to a television connected
to the AV1 TV OUT terminal on this unit.
MULTI CONTROL
1. Press [TOP MENU].
2. Press [< , >] to select “SETUP”.
è [ENTER]
3. Press [< , >] to select “AV OUT”.
è [ENTER]
4. Press [< , >] to select “DVD” or “VCR”.
è [ENTER]
5. Press [< , >] to select “RCA” or “SCART”.
è [ENTER]
The factory settings are:
DVD: RCA
VCR: RCA
8
ENTER
SFC
^
INPUT SELECTOR
VIDEO IN
MUSIC
AV/MOVE
TUNE
L AUDIO IN R
VCR 2
TUNE
RETURN
Recording on other equipment
You can record to a tape deck connected to TAPE REC (OUT)
(SC-HT07), or a DVD recorder/VCR connected to DVR/VCR1
(DVR/VCR) OUT.
1. Press [INPUT SELECTOR] to select the source to be
recorded.
2. Begin recording.
Follow your recording unit’s operating instructions.
3. Start the source to be recorded.
Note
• (SC-HT07) With a tape deck, you can record any analogue
source except TAPE.
With a DVD recorder/VCR, you can record any analogue
source except DVR/VCR1 (DVR/VCR).
• When you select DVD 6CH INPUT mode, only sound from the
front left and right channels is recorded.
• Some sources do not allow digital recording. Connect through
the analogue terminals and select "ANALOG" input.
.
The RESET function
RQT7384
The operation settings for the unit will be initialized to the
settings made at the time of shipment.
However, any preset radio stations will not be erased.
MULTI CONTROL
22
1. Press [TOP MENU].
2. Press [< , >] to select “SETUP”.
è [ENTER]
3. Press [< , >] to select “RESET”.
è [ENTER]
4. Press [< , >] to select “YES”.
è [ENTER]
SC-HT07EB-EN.fm
Page 23
Friday, May 7, 2004
4:29 PM
Remote control operation guide
This remote control can operate Panasonic, Technics and other brands (continental Europe and the United Kingdom only) of audiovisual equipment that
have remote control sensors.
Note that this remote control cannot operate some equipment and that it may not be able to perform some operations.
Set your DVD player speaker output to "small" when playing in DVD-6CH mode, provided it has speaker output setting function.
DVD
SC-HT07
RECEIVER AV SYSTEM
DVD
^
VCR
2
Switch on the television and select input
CD
3
4
5
6
7
8
9
DVD
DISC
0
u/t
y/i
AV SYSTEM
DVD
RECORDER
or
CH
VOLUME
=
MUTING
TUNER/BAND
Switch on the player and start play
Switch off
DVD
or
DVD
RECORDER
AV SYSTEM
MENU
DIRECT
NAVIGATOR
PLAY
LIST
Operating the DVD player / DVD recorder
TOP MENU
ENTER
DIRECT
NAVIGATOR
DISPLAY
STEREO/
2CH MIX
1
2
3
4
5
6
7
8
0
TV VOL
DIMMER SUBWOOFER
CENTER
FOCUS
MENU
TEST
/L
/R
SLEEP
LEVEL
EFFECT
%PL
MUSIC
AV/MOVIE
DVD
TV
^
VCR
ENTER
Show disc menus
ANALOG 6CH
DVD
TUNER/BAND RECORDER
GAME/AUX
u/t
(
Select and enter
menu items
DISPLAY
2
3
4
5
6
7
8
9
DIRECT TUNING
-/--
DISC
0
> 10
u
i
t
Show player menus
(
CH
VOLUME
MENU
RETURN
Clear menus or return to
previous menus
MENU
=
y/i
u
i
u/t
TV VOL
1
-/--
9
> 10
=
Start play from a
selected item
MENU
PLAY
LIST
SC-HT05 SFC
RECEIVER
OFF AV SYSTEM
^
Show disc menus
RETURN
TV VOL
INPUT
MODE
TONE/
BALANCE
^
q
h
TOP MENU
TV/AV
AV SYSTEM
TV
^
ANALOG 6CH
g
q
^
ANALOG 6CH
-/-> 10
DIRECT TUNING
TV/AV
^
ANALOG 6CH
DVD
DVD RECORDER
DVD/HDD RECORDER
1
AV SYSTEM
TV
TV
)
Skip items
during play
y/i
t
y
u/t
Search through
the disc (Press
and hold)
)
y/i
h
TV VOL
(
y
t
y
)
Start slow-motion play
g
h
q
TOP MENU
MENU
DIRECT
NAVIGATOR
PLAY
LIST
DIRECT TUNING
DISC
1
2
4
5
Operations
^
Watching DVDs
Switch on
3
h
Specify a disc [5-disc changer]
To view frame-by-frame
ENTER
TV VOL
MUTING
DIMMER
INPUT
MODE
TEST
TV/AV
RETURN
g
h
TV VOL
Stop play
Pause play
DVD RECORDER
DVD/HDD
DVD RECORDER
DVD/HDD
Switch between DVD and HDD
[DVD recorder with HDD]
When using
CENTER both a DVD player and a DVD recorder
SUBWOOFER FOCUS
LEVEL
EFFECT
To prevent accidental operation
• When operating a DVD recorder, use the remote control that comes with the DVD recorder.
• When using a Panasonic DVD recorder, change its remote control code to a different number such as "2" or "3". (Refer to its
Operating Instructions for details.)
RQT7384
DISPLAY
23
SC-HT07EB-EN.fm
Page 24
Friday, May 7, 2004
4:29 PM
Remote control operation guide
TV/VCR
Watching TV
SC-HT07
Switch on
RECEIVER AV SYSTEM
^
DVD
^
VCR
2
CD
4
5
6
7
8
9
DISC
0
u/t
y/i
^
VOLUME
Operating the TV
=
MUTING
TUNER/BAND
g
AV SYSTEM
TV
CH
-/-> 10
DIRECT TUNING
Switch on the television and select input
Switch off
3
TV/AV
^
ANALOG 6CH
DVD
DVD RECORDER
DVD/HDD RECORDER
1
AV SYSTEM
TV
TV
q
h
TOP MENU
MENU
DIRECT
NAVIGATOR
PLAY
LIST
1
2
3
4
CH
Change channels
sequentially
1
2
3
4
5
6
7
8
9
Select channels
directly
-/--
> 10
0
=
DISPLAY
RETURN
TV VOL
TV VOL
Adjust the volume
ENTER
DISPLAY
RETURN
TV VOL
TV/AV
TV VOL
TEST
/L
/R
TONE/
BALANCE
SLEEP
LEVEL
EFFECT
%PL
MUSIC
SC-HT05
Switch on
AV SYSTEM
TV
CENTER
FOCUS
DIMMER SUBWOOFER
INPUT
MODE
STEREO/
2CH MIX
Watching videotapes
Switch on the television and select input
AV SYSTEM
VCR
SFC
AV/MOVIE
^
^
DVD
VCR
Switch on the player and start play
TV
ANALOG 6CH
DVD
TUNER/BAND RECORDER
q
^
OFF
RECEIVER
OFF AV SYSTEM
TV/AV
^
GAME/AUX
Switch off
AV SYSTEM
VCR
TV
Operations
1
2
3
4
5
6
7
8
CH
-/--
DISC
0
> 10
u
i
t
=
g
y
h
q
TOP MENU
MENU
DIRECT
NAVIGATOR
PLAY
LIST
ENTER
RETURN
TV VOL
TV VOL
MUTING
DIMMER
INPUT
MODE
TEST
RQT7384
CENTER
SUBWOOFER FOCUS
24
%PL
TV/AV
DVD RECORDER
DVD/HDD
LEVEL
MUSIC
1
2
3
4
CH
Change channels
sequentially
g
DISPLAY
STEREO/
2CH MIX
Operating the video deck
VOLUME
9
DIRECT TUNING
EFFECT
SFC
AV/MOVIE
AV SYSTEM
^
^
1
2
3
4
5
6
7
8
9
Select channels
directly
u/t y/i
ENTER
0
Stop play
> 10
=
(
u
i
)
Rewind or fast-forward
h
Pause play
SC-HT07EB-EN.fm
Page 25
Friday, May 7, 2004
4:29 PM
SC-HT07
SC-HT07
CD
Listening to CDs
Switch on
RECEIVER AV SYSTEM
^
DVD
^
VCR
2
4
7
CD
8
9
0
u/t
y/i
Operating the CD player
=
g
^
VOLUME
-/-> 10
DISC
AV SYSTEM
CD
CH
6
DIRECT TUNING
Switch on the player and start play
Switch off
3
5
q
^
ANALOG 6CH
DVD
DVD RECORDER
DVD/HDD RECORDER
1
AV SYSTEM
CD
TV
1
6
MUTING
TUNER/BAND
2
7
3
8
4
9
5
10
1
q
h
TOP MENU
MENU
Start play from a selected track
4
5
7
8
0
PLAY
LIST
DIRECT
NAVIGATOR
2
3
DIRECT TUNING
DISC
6
9
1
2
4
5
3
Specify a disc
[3- or 5-disc changer]
-/--
> 10
=
ENTER
u/t
DISPLAY
TV VOL
TV VOL
TV/AV
CENTER
DIMMER SUBWOOFER FOCUS
INPUT
MODE
TEST
/L
/R
TONE/
BALANCE
SLEEP
LEVEL
EFFECT
STEREO/
2CH MIX
h
y/i
RETURN
%PL
MUSIC
DIRECT TUNING
Pause play
Skip tracks during play
DISC
1
2
3
4
5
6
7
8
9
q
0
Start play from a specified disc
[MEGA CD changer] (holds more than 50
discs)
SFC
AV/MOVIE
OFF
Stop play
g
Changing the codes
SC-HT07
SC-HT07
^
^
DVD
TV
PANASONIC
AKAI
ALBA
BAIRD
BAUR
BLAUPUNKT
BRANDT
BUSH
DAEWOO
DENON
DUAL
FERGUSON
FINLUX
FISHER
FUNAI
GOLDSTAR
01,29,30,31
07,11,28,36
37
05,11,12
32
28,36
26,41
02,05,10,11
12,32,38
11,12,32
32
11,12
11,12,22,23
24,25,40
37
02,38
11,12
11,12,25,32
GO-VIDEO
GRUNDIG
28,36
ANALOG 6CH
DVD
DVD RECORDER
DVD/HDD RECORDER
VCR
1
2
3
4
5
6
7
8
9
CD
CH
VOLUME
-/-> 10
DIRECT TUNING
DISC
0
u/t
y/i
=
TUNER/BAND
MUTING
Code table
TV
GOLDSTAR/LG
GOODMANS
VCR
01,29,30
06,08,16,17
19,37
02,06,23
08,10,37
DVD
01
MATSUI
METZ
MITSUBISHI
NEC
NOKIA
01,26,29,30,33
02,09,23
15
31
05,07,10,11,12
HCM
HITACHI
ICE
INNO HIT
ITT
ITT/NOKIA
JVC
KENDO
KENWOOD
LOEWE
LOEWE OPTA
LUXOR
01,17
02
NORDMENDE
OCEANIC
OKANO
ORION
PHILIPS
PHONOLA
01,09,26,41
21,39
34
05,07,37
18
40
14,33
32
37
02,05,06,07,10
11,12,25,37,38
14,19,28,36
05,07,37
26,41
27,35
02,03,05,10
11,12,38
11,12,13,15
11,12
VCR
03,04,36,37
02,03,18,23
27,33
02,23,26,28
32,33
02,23
13,14
08,10,11,37
18,27,37
20,21
08,09,37
03,32
DVD
12
11
Operations
If the code is correct, the equipment turns on or
off.
If it doesn’t, try entering another code.
• Reenter the codes after you change the
batteries.
TV
RECEIVER AV SYSTEM
09
15
08,10,11,17
19,37
03,05,09
01
17,19,21,32
04,21,36,37
08,10,11,18
22,27,37
20,21
06
02
06
05,09
22,32,33,34,35
32
04,16
RQT7384
(For continental Europe and the
United Kingdom)
Press and hold the button
corresponding to the equipment, and
enter the two digits.
(Continued on next page) 25
SC-HT07EB-EN.fm
Page 26
Friday, May 7, 2004
4:29 PM
Remote control operation guide
Code table
TV
PIONEER
POLKAUDIO
RADIOLA
RAITE
RCA
RFT
ROADSTAR
SABA
SALORA
SAMPO
SAMSUNG
SANYO
SCHAUB LORENZ
SCHNEIDER
SEG
SELECO
VCR
11,12
SHARP
SIEMENS
SINUDYNE
13
02
33
02,03,18,23,27
21
08,11,17,19,37
39
26,41
07,37
11,12,15,21
25,34,39
07,17,25,37
11,12
39,40
11,24
DVD
03
16
15,16,18,27
SONY
TECHNICS
THOMSON
THORN
02
14
10
TOSHIBA
UNIVERSUM
WHITE WESTIN
HOUSE
YAMAHA
ZENITH
07,10,11
10
02,03,18,23,27,32
02,18,23,27
TV
17,20
11,12,17,28,36
02,05,11,12
22,24,38,40
16
05,26,41
06,08,11,12
14,16,25,32
03,04,06,08
39
11,12,22,40
VCR
22
03,10,11,32
DVD
08
24,25,26
05
01
02
21
10
15,17,19,32
03,08,32,37
04
01
07,12
Advance setup (For those with expertise)
You can also change the speaker settings.
MULTI CONTROL
1. Press [<] and [>] at the same time.
2. Press [< , >] to select the sub menu. è [ENTER]
If there is a menu in level 2 as well, repeat step 2 to make the settings.
• Press [RETURN] to return to the level above.
• Press [TOP MENU] to return to the Top menu.
• Pressing [RETURN] or [TOP MENU] while the Top menu is displayed takes you immediately to the EXIT menu.
Top menu
SPEAKERS
DISTANCE
Optional speakers only
Set the size to suit your speakers.
(Large: For speakers that can reproduce the
bass range below 100 Hz)
Enter the distance of the front, center and
surround speakers from the seating position.
Sub menu (Level 1)
FILTER
EXIT
Exit
SMALL, LARGE
NONE, SMALL, LARGE
SURROUND
NONE, SMALL, LARGE
SUB-WFR
NO, YES
1.0 m
10.0 m
1.0 m
10.0 m
1.0 m
10.0 m
FRONT
CENTER
100, 150, 200 (Hz)
RQT7384
Operations
NORSK
26
Sub menu (Level 2)
FRONT
CENTER
SURROUND
Change the cut-off for bass output from the
front speakers
Note
Change these settings
only if necessary.
SAVE, NO
SUOMI
ADVARSEL!
VAROITUS!
• APPARATET MÅ IKKE PLASSERES I EN BOKHYLLE,
ET INNEBYGGET KABINETT ELLER ET ANNET
LUKKET STED HVOR VENTILASJONSFORHOLDENE
ER UTILSTREKKELIGE. SØRG FOR AT GARDINER
ELLER LIGNENDE IKKE FORVERRER
VENTILASJONSFORHOLDENE, SÅ RISIKO FOR
ELEKTRISK SJOKK ELLER BRANN FORÅRSAKET AV
OVERHETING UNNGÅS.
• APPARATETS VENTILASJONSÅPNINGER MÅ IKKE
DEKKES TIL MED AVISER, BORDDUKER, GARDINER
OG LIGNENDE.
• PLASSER IKKE ÅPEN ILD, SLIK SOM LEVENDE LYS,
OPPÅ APPARATET.
• BRUKTE BATTERIER MÅ KASSERES UTEN FARE FOR
MILJØET.
• ÄLÄ ASENNA TAI LAITA TÄTÄ LAITETTA
KABINETTITYYPPISEEN KIRJAKAAPPIIN TAI
MUUHUN SULJETTUUN TILAAN, JOTTA TUULETUS
ONNISTUISI. VARMISTA, ETTÄ VERHO TAI MIKÄÄN
MUU MATERIAALI EI HUONONNA TUULETUSTA,
JOTTA VÄLTETTÄISIIN YLIKUUMENEMISESTA
JOHTUVA SÄHKÖISKU- TAI TULIPALOVAARA.
• ÄLÄ PEITÄ LAITTEEN TUULETUSAUKKOJA
SANOMALEHDELLÄ, PÖYTÄLIINALLA, VERHOLLA
TAI MUULLA VASTAAVALLA ESINEELLÄ.
• ÄLÄ ASETA PALAVAA KYNTTILÄÄ TAI MUUTA
AVOTULEN LÄHDETTÄ LAITTEEN PÄÄLLE.
• HÄVITÄ PARISTOT LUONTOA
VAHINGOITTAMATTOMALLA TAVALLA.
ADVARSEL:
TULIPALO-, SÄHKÖISKUVAARAN TAI TUOTETTA
KOHTAAVAN MUUN VAHINGON VÄHENTÄMISEKSI EI
LAITETTA SAA ALTISTAA SATEELLE, KOSTEUDELLE,
VESIPISAROILLE TAI ROISKEELLE, EIKÄ NESTETTÄ
SISÄLTÄVIÄ ESINEITÄ, KUTEN ESIMERKIKSI
MALJAKOITA, SAA ASETTAA LAITTEEN PÄÄLLE.
FOR Å REDUSERE FAREN FOR BRANN, ELEKTRISK
STØT ELLER SKADER PÅ PRODUKTET, MÅ DETTE
APPARATET IKKE UTSETTES FOR REGN, FUKTIGHET,
VANNDRÅPER ELLER VANNSPRUT. DET MÅ HELLER
IKKE PLASSERES GJENSTANDER FYLT MED VANN,
SLIK SOM BLOMSTERVASER, OPPÅ APPARATET.
DETTE APPARATET ER BEREGNET TIL BRUK UNDER
MODERATE KLIMAFORHOLD.
VAROITUS:
TÄMÄ LAITE ON TARKOITETTU
LEUDOSSA ILMASTOSSA.
KÄYTETTÄVÄKSI
SC-HT07EB-EN.fm
Page 27
Friday, May 7, 2004
4:29 PM
Specifications (DIN 45 500)
n AMPLIFIER SECTION
n SPEAKER SECTION
RMS output power of each channel driven
(at 240 V for areas other than continental Europe)
10 % total harmonic distortion
1 kHz front CH
[SC-HT07] 60 W per channel (6 Ω)
[SC-HT05] 55 W per channel (6 Ω)
1 kHz surround CH
[SC-HT07] 60 W per channel (6 Ω)
[SC-HT05] 55 W per channel (6 Ω)
1 kHz center CH
[SC-HT07] 220 W per channel (6 Ω)
[SC-HT05] 160 W per channel (6 Ω)
100 Hz subwoofer CH
[SC-HT07] 240 W per channel (4 Ω)
[SC-HT05] 220 W per channel (4 Ω)
Total RMS output power
[SC-HT07] 700 W
[SC-HT05] 600 W
DIN power output: Dolby Digital Mode
(at 240 V for areas other than continental Europe)
T.H.D. 1%
1 kHz front CH
35 W per channel (6 Ω)
1 kHz surround CH
35 W per channel (6 Ω)
1 kHz center CH
[SC-HT07] 150 W per channel (6 Ω)
[SC-HT05] 140 W per channel (6 Ω)
100 Hz subwoofer CH
[SC-HT07] 160 W per channel (4 Ω)
[SC-HT05] 150 W per channel (4 Ω)
Total DIN output power
[SC-HT07] 450 W
[SC-HT05] 430 W
DIN power output: Stereo Mode
(at 240 V for areas other than continental Europe)
T.H.D. 1 %
1 kHz front CH
35 W per channel (6 Ω)
100 Hz subwoofer CH
[SC-HT07] 160 W per channel (4 Ω)
[SC-HT05] 150 W per channel (4 Ω)
Total DIN output power
[SC-HT07] 230 W
[SC-HT05] 220 W
Total harmonic distortion
Half power at 1 kHz (Front CH)
0.1 % (6 Ω)
Input sensitivity
[SC-HT07] DVD, DVR/VCR1, TV, TAPE, CD, VCR2
[SC-HT05] DVD, DVR/VCR, TV, GAME/AUX
600 mV
S/N at rated power (6 Ω)
[SC-HT07] DVD, DVR/VCR1, TV, TAPE, CD, VCR2
[SC-HT05] DVD, DVR/VCR, TV, GAME/AUX
75 dB (85 dB, IHF’66)
Input impedance
[SC-HT07] DVD, DVR/VCR1, TV, TAPE, CD, VCR2
[SC-HT05] DVD, DVR/VCR, TV, GAME/AUX
47 kΩ
Tone controls
BASS
50 Hz, +10 to -10 dB
TREBLE
20 kHz, +10 to -10 dB
Front/Surround speaker
(SC-HT07:SB-FS927) (SC-HT05:SB-PF725/SB-PS725)
Type
[SC-HT07] 2 Way, 3 Speaker, Bass-ref.
[SC-HT05] 2 Way, 2 Speaker, Bass-ref.
Speaker unit
Full range
[SC-HT07] 6.5 cm cone type x 2, 6 Ω
[SC-HT05] 6.5 cm cone type, 6 Ω
Super tweeter (SB-FS927,SB-PF725)
6 cm Ring Shaped Dome type, 6 Ω
Tweeter (SB-PS725)
6 cm cone type, 6 Ω
Input power (IEC)
[SC-HT07] 60 W (Max)
[SC-HT05] 55 W (Max)
Output sound pressure level
[SC-HT07] 85 dB/W (1.0 m)
[SC-HT05] 80 dB/W (1.0 m)
Crossover frequency
[SC-HT07] 800 Hz, 7 kHz
[SC-HT05] 5 kHz
Frequency range
[SC-HT07] 96 Hz-50 kHz (-16 dB)
120 Hz-45 kHz (-10 dB)
[SC-HT05] 95 Hz-41 kHz (-16 dB)
110 Hz-40 kHz (-10 dB)
Dimensions (W x H x D)
[SC-HT07] 240 x 678 to 1138 x 240 mm
[SC-HT05] 86 x 240 x 115 mm
Mass
[SC-HT07] 4.20 kg
[SC-HT05] 0.89 kg
2
1
n FM TUNER SECTION
Frequency range
Sensitivity
S/N 30 dB
S/N 26 dB
S/N 20 dB
IHF usable sensitivity
IHF 46 dB stereo quieting sensitivity
Total harmonic distortion
MONO
STEREO
S/N
MONO
STEREO
Frequency response
Image rejection at 98 MHz
IF rejection at 98 MHZ
Stereo separation
1 kHz
Antenna terminal
87.50-108.00 MHz
1.5 µV/75 Ω
1.3 µV/75 Ω
1.2 µV/75 Ω
(IHF '58) 1.5 µV/75 Ω
22 µV/75 Ω
0.2 %
0.3 %
60 dB (71 dB, IHF)
58 dB (65 dB, IHF)
20 Hz-15 kHz, +1 dB, -2 dB
40 dB
70 dB
40 dB
75 Ω (unbalanced)
n AM TUNER SECTION
Frequency range
Sensitivity
Selectivity (at 999 kHz)
522-1611 kHz (9 kHz steps)
530-1620 kHz (10 kHz steps)
450 µV/m
35 dB
n VIDEO SECTION
Output voltage at 1 V input (unbalanced)
Maximum input voltage
Input/output impedance
1±0.1 Vp-p
1.5 Vp-p
75 Ω
n GENERAL
Power supply
For the United Kingdom, Australia and New Zealand
AC 230-240 V, 50 Hz
For continental Europe
AC 230 V, 50 Hz
For other areas
AC 220-240 V, 50/60 Hz
Power consumption
(Main unit)
25 W
(Subwoofer)
[SC-HT07] 290 W
[SC-HT05] 250 W
Dimensions (W x H x D) (Main unit)
430 x 68 x 287 mm
Mass (Main unit)
2.0 kg
Reference
OPTICAL
COAXIAL
Active subwoofer (SC-HT07:SB-WA07) (SC-HT05:SB-WA05)
Type
1 Way 1 Speaker, Bass-ref.
Speaker unit (Woofer)
17 cm cone type, 4 Ω
Input power (IEC)
[SC-HT07] 240 W (Max)
[SC-HT05] 220 W (Max)
Output sound pressure level
80 dB/W (1.0 m)
Frequency range
32-220 Hz (-16 dB)
36-190 Hz (-10 dB)
Dimensions (W x H x D)
209 x 361 x 463 mm
Mass
[SC-HT07] 11.8 kg
[SC-HT05] 11.5 kg
Power consumption in standby mode:
1W
Notes:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum analyzer.
Maintenance
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this unit.
• Before using chemically treated cloth, read the instructions that came
with the cloth carefully.
RQT7384
Digital input
Center speaker (SC-HT07:SB-PC927) (SC-HT05:SB-PC725)
Type
2 Way, 3 Speaker, Bass-ref.
Speaker unit
Full range
6.5 cm cone type x 2, 6 Ω
[SC-HT07] Super tweeter
6 cm Ring Shaped Dome type, 6 Ω
[SC-HT05] Tweeter
6 cm cone type, 6 Ω
Input power (IEC)
[SC-HT07] 220 W (Max)
[SC-HT05] 160 W (Max)
Output sound pressure level
[SC-HT07] 84 dB/W (1.0 m)
[SC-HT05] 83 dB/W (1.0 m)
Crossover frequency
5 kHz
Frequency range
[SC-HT07] 110 Hz-50 kHz (-16 dB)
130 Hz-46 kHz (-10 dB)
[SC-HT05] 92 Hz-41 kHz (-16 dB)
110 Hz-40 kHz (-10 dB)
Dimensions (W x H x D)
[SC-HT07] 320 x 97 x 93 mm
[SC-HT05] 300 x 103 x 117 mm
Mass
[SC-HT07] 1.50 kg
[SC-HT05] 1.48 kg
27
SC-HT07EB-EN.fm
Page 28
Friday, May 7, 2004
4:29 PM
Troubleshooting guide
Before requesting service, make the below checks.
If you can’t fix the unit as described or if something not listed here occurs, contact your dealer.
Common problems
No power.
No sound or no picture.
“F76” appears on the
display, and the unit turns
off.
“FAN LOCK” appears on
the display.
“F 70” appears on the
display.
Pages
• Ensure the AC mains lead and system cable are connected.
8
•
•
•
•
•
•
•
13
7-11
13
22
9
20
9, 22
Turn the volume up.
Check connections to speakers and other equipment.
Select the correct source.
Change the D-INPUT setting to suit the type of connection you have made.
Check that the digital signals can be decoded by this unit.
Turn PCM FIX or DTS FIX off.
Check the AV output settings and set them to suit the connections (RCA or
SCART) you have made.
• Determine and correct the cause, then turn the unit on.
Causes include:
− Shorting (bare wires touching) of positive and negative speaker wires.
− Using the subwoofer in a hot environment without proper ventilation.
Consult your dealer if the problem occurs again after turning the unit on.
7
–
• Turn the unit off, disconnect the AC mains lead, and consult your dealer.
–
Sound modes
Pages
Sound is not heard from
the center, surround, or
subwoofer speakers.
• Turn 2CH MIX off.
• The source may be stereo. Change the sound mode.
13
13
Cannot use Dolby Pro
LogicII or SFC.
• You cannot use Dolby Pro LogicII or SFC when input is PCM with
sampling frequencies of 96 or 88.2 kHz.
13
Radio
The radio cannot be tuned
in or there is a lot of noise
and interference.
There is a lot of noise
when listening to AM.
The correct AM frequency
cannot be tuned in.
Pages
• Connect the appropriate antenna. (You may need an outdoor antenna or
one with more elements.)
• Adjust the position of the FM or AM antenna.
• Reduce the treble.
• Turn off nearby televisions, video decks and DVD players.
• Separate the antenna from other cables, leads, and appliances.
10
• Press and hold [MULTI CONTROL, ENTER] on the main unit so “DEFEAT”
appears (the DSP is defeated). This should reduce noise. The unit cannot
play multiple channel sound while the DSP is defeated, so repeat this to
reengage the DSP.
–
• Change the frequency step.
17
NORSK
Utstyret bør plasseres i nærheten av AC-stikkontakten, og
støpslet må være lett tilgjengelig hvis det skulle oppstå
problemer.
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
10
21
–
–
SUOMI
Laite tulee asettaa lähelle verkkopistorasiaa ja pistokkeen
täytyy olla sellaisessa asennossa, että siihen on helppo
tarttua ongelman sattuessa.
En
RQT7384-3B
H0104SG3044
Download PDF

advertising