Panasonic WJMS424 Operating Instructions

Panasonic WJMS424 Operating Instructions
ENGLISH
DEUTSCH
ESPAÑOL
WJ-MS424
FRANÇAIS
Quad Unit
Before attempting to connect or operate this product, please read these instructions completely
ENGLISH VERSION
For Australia
THIS APPARATUS MUST BE EARTHED.
To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively
earthed through the normal household wiring. Extension cords used
with the equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major
cause of fatalities.
The fact that the equipment operates satisfactorily does not imply
that the power point is earthed and that the installation is completely
safe. For your safety, if in any doubt about the effective earthing of
the power point, consult a qualified electrician.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK), NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
interned to alert the user to the presence
of uninsulated "dangerous voltage" within
the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the appliance.
The serial number of this product may be found on the
rear of the unit.
You should note the serial number of this unit in the
space provided and retain this book as a permanent
record of your purchase to aid identification in the event
of theft.
CAUTION:
Before attempting to connect or operate this product, please read the label on the bottom.
For U.K.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your
safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement
fuse has a rating of 13 amp and that it is approved by ASTA or BSI to
BS1362.
or the BSI mark
on the body of the
Check for the ASTA mark
fuse.
If the plug contains a removable fuse cover you must ensure that it is
refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement
cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic
Dealer.
H
G
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE
REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE
CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown
below.
If in any doubt please consult a qualified electrician.
WARNING: This apparatus must be earthed.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code.
Green-and-yellow:
Earth
Blue:
Neutral
Brown:
Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected to
the terminal in the plug which is marked with the letter E or by the earth
symbol I or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal in
the plug which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
in the plug which is marked with the letter L or coloured red.
How to replace the fuse
Open the fuse compartment with
a screwdriver and replace the fuse
and fuse cover.
Model No.
Serial No.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
PREFACE .................................................................................................................................................................................. 2
FEATURES ................................................................................................................................................................................ 2
PRECAUTIONS ......................................................................................................................................................................... 2
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ................................................................................................... 3
RACK MOUNTING .................................................................................................................................................................... 5
SETTING UP THE MENUS ........................................................................................................................................................ 6
SYSTEM CONNECTIONS ....................................................................................................................................................... 12
SPECIFICATIONS ................................................................................................................................................................... 16
STANDARD ACCESSORIES ................................................................................................................................................... 16
We declare under our sole responsibility that the product to which
this declaration relates is in conformity with the standards or other
normative documents following the provisions of Directives
EEC/73/23 and EEC/89/336.
Vi erklærer os eneansvarlige for, at dette produkt, som denne
deklaration omhandler, er i overensstemmelse med den følgende
standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC.
Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das
sich diese Erklärung bezieht, mit der folgenden Normen oder normativen Dokumenten übereinstimmt. Gemäß den Bestimmungen
der Richtlinite 73/23/EEC und 89/336/EEC.
Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken
denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i Direktiv
73/23/EEC och 89/336/EEC.
Nosotros declaramos bajo nuestra única responsabilidad que el
producto a que hace referencia esta declaración està conforme con
las normas u otros documentos normativos siguiendo las estipulaciones de la directivas CEE/73/23 y CEE/89/336.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä
ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC ia
89/336/EEC. säädöksiä.
Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto
a cui si riferisce la presente dichiarazione risulta conforme ai
seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive CEE/73/23 e CEE/89/336.
Vi erklærer oss alene ansvarlige for at produktet som denne
erklæringen gjelder for, er i overensstemmelse med følgende
normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiven 73/23/EEC og 89/336/EEC.
Wij verklaren als enige aansprakelijke, dat het product waarop deze
verklaring betrekking heeft, voldoet aan de volgende normen of
andere normatiefve dokumenten, overeenkomstig de bepalingen
van Richtlijnen 73/23/EEC en 89/336/EEC.
-1-
ENGLISH
CONTENTS
PREFACE
the system, and if desired, the monitor can be divided
into 4 windows for simultaneous display of the four different images.
Simple front panel switch operation allows quick selection between quad and single camera display modes.
The Panasonic WJ-MS424 Quad Unit is ideal for CCTV
applications where multiple surveillance cameras are
required. Most 2 : 1 interlace cameras available today,
either colour or black and white, are compatible with the
WJ-MS424. Up to four cameras may be connected to
FEATURES
4. Quad Picture Borderlines
A white borderline can be inserted in the quad pictures by setting “BORDER ON” from the Setup
Menu.
5. Two kinds of Video Output Connectors
The Quad system offers two kinds of video output
connectors :
(a) VIDEO OUT : Quad or full-size single picture
can be selected with the front panel switches.
(b) VTR OUT : A quad display is always supplied,
regardless of the setting of the front panel
switches.
6. A back-up memory inside maintains preset title
character information.
7. Video Loss Checking Function
If the video signal is lost due to a disconnected
cable or other reasons, an alarm buzzer beeps and
a caution message is displayed on the monitor
screen.
1. Compatible with Most 2 : 1 Interlace cameras
Advanced digital processing technology allows
connection of most 2 : 1 interlace cameras available
today without the requirement for synchronization of
the four video inputs.
The system may be added to existing security systems and makes possible displays in black and
white or full colour.
2. Alphanumeric Character Generator
Title insertion of up to 8 characters in each of the
four windows is possible. This promotes easy identification of the separate camera locations.
3. Alarm with Built-in Buzzer
This system can be combined with alarm sensors
and switches as well as time-lapse VTRs through
the alarm output and reset signal connectors.
Upon receiving an alarm signal, a full-sized picture
of the site is displayed. By setting the “CAM TITLE
ON” and “ALARM TITLE ON” modes from the TITLE
menu, “ALARM” and the window title will appear
intermittently in the picture.
The Automatic alarm reset time is adjustable from 1
to 30 sec.,1, 2, 3, 4, 5 min. or Off.
PRECAUTIONS
• Handle the unit with care.
• Take immediate action if ever the unit does become
wet. Tune the power off and refer servicing to qualified service personnel. Moisture can damage the
unit and also create a danger of electric shock.
• Use the unit under conditions where temperature is
within –10°C to +50°C (14°F to 122°F), and humidity
is below 90%. When installing the unit in the rack, it
is recommended to install the fan.
• The input power source is 220 - 240 V AC, 50 Hz.
• Refer all installation work to qualified service personnel or system installers.
• Do not attempt to disassemble the unit. In order to
prevent electrical shock, do not remove screws or
covers. There are no user-serviceable parts inside.
• Do not abuse the unit. Avoid striking, shaking etc. It
could be damaged by improper handling or storage.
• Do not use strong or abrasive detergents when
cleaning the unit body.
• Do not expose the unit to water or moisture, and do
not operate it in wet or humid areas.
• Do not use the unit in an extreme environment
where high temperature or high humidity exists.
-2-
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
ALARM
POWER
ON
OFF
VIDEO SELECT
ALARM RESET
QUAD/SEQ
1
POWER
PROTECTION
2
IN
OUT 3
IN
4
+
–
ESC
CURSOR
OUT 4
MENU
3
VIDEO
OUT 2
IN
OUT 1
SELECT
Quad System WJ-MS
VTR
OUT
IN
VIDEO
OUT
ALARM/REMOTE
SIGNAL GND
1. Power ON/OFF Switch (POWER)
• QUAD button
When QUAD is selected for VIDEO OUT on the
SYSTEM SETUP menu, this button works as the
QUAD button.
Pressing this button displays the quad picture on
the monitor screen.
This switch turns the power of this switch on or off. The
POWER indicator lights when the power of this unit is
on.
Switch Protector (Standard Accessory)
To prevent that the power of this unit is turned off accidentally, install the supplied switch protector as shown
below.
• SEQ button
When SEQ is selected for VIDEO OUT on the SYSTEM SETUP menu, this button works as the SEQ
button.
Pressing this button displays the pictures on the
monitor screen in the sequential order and with the
dwell time set on the SEQ SETUP menu.
SWITCH
PROTEC
TOR
• ESC button
When the setup menu (SYSTEM SETUP, SEQ
SETUP, TITLE SETUP, TITLE SET or TITLE POSI) is
displayed on the monitor screen, this button works
as the ESC button.
2. Alarm LED (ALARM)
This LED flashes while the alarm signal is received.
It changes to steady light when the alarm is reset
automatically.
To turn the flashing LED off, press the ALARM
RESET/QUAD/SEQ button.
Pressing this button returns the current setup menu to
the previous setup menu.
4. VIDEO SELECT (1, 2, 3, 4)/CURSOR
(4, 5)/SELECT(–, +) Buttons
These buttons select the video signal or move the
cursor on the setup menus.
• VIDEO SELECT(1, 2, 3, 4) buttons
When the setup menu is not displayed, these buttons work as VIDEO SELECT buttons.
Pressing one of these buttons selects a channel to
be displayed in single picture mode.
• CURSOR (4, 5)/SELECT(–, +) buttons
When the setup menu is displayed, these buttons
work as CURSOR (4, 5)/SELECT (–, +) buttons.
Pressing these buttons moves the cursor or select s
a mode or a parameter.
3. Alarm Reset/Quad/Sequence/Escape Button
(ALARM RESET/QUAD/SEQ/ESC)
This button has different functions in different
modes, as described below.
• ALARM RESET button
When an alarm signal is received, this button works
as the ALARM RESET button.
Pressing this button in an alarm situation cancels
the alarm mode with the following results:
1. The alarm LED stops flashing.
2. The alarm output is stopped.
3. The alarm buzzer stops beeping.
4. The video loss caution message on the monitor
screen disappears and the screen returns to
the camera picture.
-3-
4 button: This button moves the cursor to the left or
selects an item on the setup menus.
5 button: This button moves the cursor to the right
or selects an item on the setup menus.
– button: This button selects a character or a parameter on the setup menus.
+ button: This button selects a character or a parameter on the setup menus.
7. Video Output Connectors
(VIDEO OUT 1, 2, 3, 4)
The video input signals connected to the VIDEO IN
connector are looped through to these connectors.
Connectors a coaxial cable to these connectors
cancels the termination.
8. VTR Output Connector (VTR OUT)
The video signal for the quad picture mode is
always provided at this connector. By connecting it
to the VIDEO IN connector of the time lapse VTR,
you can record the quad picture.
5. Menu Button (MENU)
Pressing this button for approx. 2 seconds displays
the setup menus. Pressing it again for approx. 1
second cancels the display of the setup menus.
9. Video Output Connector (VIDEO OUT)
The video signal selected by the QUAD/SEQ button
(quad picture) or the VIDEO SELECT button (single
picture) is output from this connector.
6. Video input Connector (VIDEO IN 1, 2, 3, 4)
These connectors receive a composite video signal.
They are automatically terminated.
Notes:
• The input signals must meet the CCIR B/W
video signal standard, if the video inputs of this
unit are to be synchronized.
• If the input signals have a high jitter content, as
in the case of a VTR playback picture, it may
not be possible to synchronize this unit.
10. Alarm/Remote Control Connector
(ALARM/REMOTE)
This connector accepts the alarm signal from associated alarm sensor units and the remote control
signal from the external equipment.
ALARM RECOVER IN
QUAD/SEQ
Menu
ALARM RESET OUT
Selector
Not Used
REMOTE/ALARM 4
ALARM OUT
REMOTE/ALARM 3
Not Used
REMOTE/ALARM 2
REMOTE/ALARM 1
Not Used
13
12
25
11
24
10
23
9
22
8
21
7
20
6
19
5
18
4
17
3
16
2
15
1
14
GND
Pin-14 to 25 are connected to Ground
Caution: The input voltage should be DC 24V or
less for ALARM IN.
11. Power Cord
-4-
RACK MOUNTING
To install the WJ-MS424 Quad Unit in an EIA 19-inch
rack, use the rack mounting brackets (provided) and
eight screws (provided, M3x10).
4. Install the unit in the rack with four screws (to be
procured locally).
1. Turn off the power of the unit.
EIA 19”
rack
2. Remove the four screws fixing the rubber legs, and
remove the four rubber legs from the unit.
Cautions:
1. Leave one space free both above and below the
unit, or install a cooling fan in the rack.
2. If the rack is subject to vibrations, secure the rear of
the unit to the rack using additional rack mounting
brackets (to be procured locally).
Remove four rubber legs.
3. Attach the rack mounting brackets on both sides
and fix them with eight screws (provided).
Eight screws (Provided)
Fix the rack mounting brackets
-5-
SETTING UP THE MENUS
Before the Settings
2. How to Operate the Menus
1. Confirm that the cameras and peripherals are connected correctly and firmly.
2. Turn on the power of this unit and connected
peripherals.
To select the desired item, press the CURSOR (4,
5) buttons. Each time you press a button, the cursor moves to the next (5) or previous (4) item.
1
2
1. Displaying the Menus
Press the MENU button for 2 seconds or more.
The MAIN menu appears.
To select the desired parameter of the selected
item, press the SELECT (–, +) buttons.
3
4
–
+
Note:
Some items have a setting menu (The “*” mark
indicates that a setting menu exists, for example, SYSTEM SETUP.), press the SELECT (–, +)
buttons to select ON for its parameter. The setting menu of the selected item appears.
ALARM
VIDEO SELECT
ALARM RESET
QUAD/SEQ
1
2
MENU
3
CURSOR
Precaution:
Entering the setup menu is not possible while
the ALARM LED is flashing. Make sure the
alarm mode is canceled. To cancel the alarm
mode, press the ALARM RESET button.
4
+
–
ESC
SELECT
All Reset Operation
All reset allows you to reset all setup menu items to
the factory settings if you are unsure about the correct settings.
Proceed as follows:
1. Turn the power of this unit off.
2. Keep holding down the CURSOR button (5),
the SELECT button (+), and the MENU button
simultaneously, and press the POWER button.
The buzzer beeps when all settings are reset to
the factory settings.
** MAIN **
SYSTEM SETUP *
ALARM BUZZER
ALARM OUT
ALARM AUTO RESET
SEQ SETUP *
TITLE SETUP *
2SEC
2SEC
OFF
You can setup the following items:
• SYSTEM SETUP
• ALARM BUZZER
• ALARM OUT
• ALARM AUTO RESET
• SEQ SETUP
• TITLE SETUP
See the following pages for details about the functions and settings.
-6-
3. Setup Menu Description
ALARM
VIDEO SELECT
ALARM RESET
QUAD/SEQ
1
3-1. SYSTEM SETUP
2
MENU
3
4
+
–
ESC
CURSOR
SELECT
The SYSTEM menu lets you set the following
items:
• BORDER
• VIDEO OUT
• AUTO SKIP
• VIDEO LOSS
or
** SYSTEM SETUP **
1. Move the cursor to SYSTEM SETUP.
2. Press one of the SELECT buttons (– or +). The SYSTEM SETUP menu appears on the monitor screen.
Note: To return to the MAIN menu, press the ESC
button.
ALARM
VIDEO SELECT
ALARM RESET
QUAD/SEQ
1
2
ON
QUAD
OFF
ON
MENU
3
4
+
–
ESC
BORDER
VIDEO OUT
AUTO SKIP
VIDEO LOSS
CURSOR
SELECT
or
** SYSTEM SETUP **
BORDER
VIDEO OUT
AUTO SKIP
VIDEO LOSS
ON
QUAD
OFF
ON
e
Borderline (white)
3-1-1. Border (BORDER)
This parameter lets you set the appearance of the borders that divide the screen.
1. Move the cursor to BORDER.
2. Select ON or OFF.
ON: The borders appear when QUAD is selected
for VIDEO OUT.
OFF: The borders do not appear.
ALARM
VIDEO SELECT
ALARM RESET
QUAD/SEQ
1
2
CURSOR
This parameter lets you select the quad picture or
sequential single picture for display on the monitor
screen.
1. Move the cursor to VIDEO OUT.
2. Select QUAD or SEQ.
QUAD: The quad picture appears on the monitor
that is connected to the VIDEO OUT connector.
SEQ: The single picture appears sequentially in
the order to set on the of SEQUENCE SETUP
submenu of the MAIN menu.
MENU
3
4
+
–
ESC
3-1-2. Quad/Sequence (VIDEO OUT)
SELECT
or
** SYSTEM SETUP **
BORDER
VIDEO OUT
AUTO SKIP
VIDEO LOSS
ON
QUAD
OFF
ON
** SYSTEM SETUP **
BORDER
VIDEO OUT
AUTO SKIP
VIDEO LOSS
-7-
ON
QUAD
OFF
ON
3-1-3. Auto Channel Skipping (AUTO SKIP)
Setting
3-1-4. Video Loss Checking (VIDEO LOSS)
This parameter lets you activate a function that checks
whether the video signal is being supplied to the VIDEO
INPUT connector.
1. Move the cursor to VIDEO LOSS.
2. Select ON or OFF.
OFF: The video loss alarm is ignored.
ON: When video loss alarm is received, the picture
switches to the quad format. The message
“CHXX LOSS” appears on the monitor screen
and the alarm buzzer starts beeping.
This parameter lets you set automatic skipping of channels to which no camera is connected.
1. Move the cursor to AUTO SKIP.
2. Select ON or OFF.
ON: Channels to which no camera is connected are
skipped when SEQ is selected.
OFF: No channels are skipped.
** SYSTEM SETUP **
BORDER
VIDEO OUT
AUTO SKIP
VIDEO LOSS
ON
QUAD
OFF
ON
** SYSTEM SETUP **
BORDER
VIDEO OUT
AUTO SKIP
VIDEO LOSS
ON
QUAD
OFF
OFF
** SYSTEM SETUP **
BORDER
VIDEO OUT
AUTO SKIP
VIDEO LOSS
ON
QUAD
ON
ON
3-2. ALARM BUZZER
This parameter lets you adjust the buzzer time between
1 and 30 seconds and 1 and 5 minutes.
1. Move the cursor to ALARM BUZZER.
2. Select the buzzer time.
OFF: The alarm buzzer does not beep when an
alarm signal is received.
1-30 SEC, 1-5 MIN: The buzzer keeps on beeping
for the duration you set.
EXT: The alarm buzzer keeps on beeping until an
operation is performed from an external equipment such as a time lapse VTR.
1
1
2
d
** MAIN **
3
SYSTEM SETUP *
ALARM BUZZER
ALARM OUT
ALARM AUTO RESET
SEQ SETUP *
TITLE SETUP *
3
4
OFF
4
1SEC
2SEC......30SEC
1MIN......5MIN
-8-
2SEC
2SEC
OFF
EXT
3-3. ALARM OUT
** MAIN **
This parameter lets you adjust the duration the alarm
signal is output between 1 and 30 seconds and 1 and 5
minutes.
1. Move the cursor to ALARM OUT.
2. Select the duration the alarm signal is output.
1-30 SEC, 1-5 MIN: The alarm signal is output for
the duration you set.
SYSTEM SETUP *
ALARM BUZZER
ALARM OUT
ALARM AUTO RESET
SEQ SETUP *
TITLE SETUP *
2SEC
2SEC
OFF
** MAIN**
ALARM
SYSTEM SETUP *
ALARM BUZZER
ALARM OUT
ALARM AUTO RESET
SEQ SETUP *
TITLE SETUP *
VIDEO SELECT
ALARM RESET
QUAD/SEQ
1
2SEC
2SEC
OFF
2
MENU
3
4
+
–
ESC
CURSOR
SELECT
or
1SEC......30SEC
1MIN......5MIN
** SEQ SETUP **
1:
2:
3:
4:
5:
6:
7:
8:
3-4. ALARM AUTO RESET
This parameter lets you set the time until the unit recovers after receiving the alarm signal.
1. Move the cursor to ALARM AUTO RESET.
2. Select the recover time.
OFF: The alarm condition is maintained until the
ALARM RESET button on the front panel is
pressed or the alarm recover signal from the
time lapse VTR is supplied to the ALARM/
REMOTE connector.
1-30 SEC, 1-5 MIN: The alarm condition is maintained for the length of the recover time you set.
OFF
1SEC......30SEC
2SEC
2SEC
2SEC
2SEC
3. Press the SELECT buttons (–, +) to select the channel. The channel changes as below:
<Channel>
1CH
2CH
3CH
4CH
QUAD
OFF
4. Press the CURSOR buttons (4 or 5) so that “SEC”
starts blinking.
The cursor moves in the SEQ SETUP menu as
shown below:
** MAIN **
SYSTEM SETUP *
ALARM BUZZER
ALARM OUT
ALARM AUTO RESET
SEQ SETUP *
TITLE SETUP *
1CH
2CH
3CH
4CH
OFF
OFF
OFF
OFF
2SEC
2SEC
OFF
** SEQUENCE **
1:
2:
3:
4:
5:
6:
7:
8:
1MIN......5MIN
1CH
2CH
3CH
4CH
OFF
OFF
OFF
OFF
2SEC
2SEC
2SEC
2SEC
: Cursor Move
3-5. SEQ SETUP
5. Select the dwell time by pressing the SELECT buttons
(–, +). The dwell time changes as below:
This parameter lets you set the sequential order and
dwell time for camera switching.
1. Move the cursor to SEQ SETUP.
2. Press one of the SELECT buttons (– or +). The
SEQUENCE menu appears on the monitor screen,
and “1 CH” starts blinking.
<Display time>
1SEC
2SEC
3SEC • • • • 30SEC
6. Repeat steps 3 to 5 to determine the sequential order
and dwell time.
7. Press the ESC button to return to the MAIN menu.
-9-
3-6. TITLE SETUP
** TITLE SETUP **
A title consisting of up to 8 alphanumeric characters
can be displayed on the monitor.
CAM TITLE
TITLE SET *
TITLE POSI *
ALARM TITLE
ON
ON
1. Move the cursor to TITLE SETUP.
2. Press one of the SELECT buttons (– or +). The
TITLE SETUP menu appears on the monitor screen.
** MAIN **
SYSTEM SETUP *
ALARM BUZZER
ALARM OUT
ALARM AUTO RESET
SEQ SETUP *
TITLE SETUP *
2SEC
2SEC
OFF
ABCDEFGH
3-6-2. TITLE SET
ALARM
VIDEO SELECT
ALARM RESET
QUAD/SEQ
1
2
MENU
3
+
–
ESC
This parameter lets you edit a displayed title.
1. Move the cursor to TITLE SET.
2. Press one of the SELECT buttons (– or +). The
EDITTING menu appears on the monitor screen
and “1” starts blinking.
3. Move the cursor to the channel number whose title
is to be edited by pressing the CURSOR buttons (4
or 5).
4. Select a character by pressing the SELECT buttons
(– or +).
5. After selecting the first character, press the CURSOR button(5). Then select the second character.
6. Repeat steps 3 to 5 above to complete the title.
7. Repeat steps 3 to 6 to edit the other channels.
8. Press the ESC button to return to the previous
menu.
4
CURSOR
SELECT
or
** TITLE SETUP **
CAM TITLE
TITLE SET *
TITLE POSI *
ALARM TITLE
ON
ON
** TITLE SETUP **
You can set the following items:
• CAM TITLE
• TITLE SET
• TITLE POSI
• ALARM TITLE
Note: To return to the MAIN menu, press the ESC
button.
CAM TITLE
TITLE SET *
TITLE POSI *
ALARM TITLE
TITLE EDIT
ALARM
ON
ON
ON
VIDEO SELECT
ALARM RESET
QUAD/SEQ
1
2
3
MENU
4
+
–
ESC
CURSOR
SELECT
3-6-1. CAM TITLE
or
This parameter lets you decide whether or not to have
the title displayed.
1. Move the cursor to the CAM TITLE parameter.
2. Select ON or OFF.
ON: Title display.
OFF: No title display.
-10-
1.......
2.......
3.......
4.......
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
Ä Ü Ö Æ Ñ Å Ø
0 1 2 3 4 5 6 7 8 9
← → = ?' " # & ( )* + ,
- . / : ; E (blank)
3-6-4. ALARM TITLE
To erase a specific character
1. Select a character to be erased.
2. Select “•” (blank mark) to erase the character.
This parameter lets you decide whether or not to have
the word”ALARM” displayed when the unit receives the
alarm signal.
1. Move the cursor to ALARM TITLE .
2. Select ON or OFF.
ON: “ALARM” is displayed
OFF: “ALARM” is not displayed.
To erase the title of a specific channel
1. Move the cursor to the channel number whose title
is to be erased.
2. Press the SELECT buttons (– and +) simultaneously.
3-6-3. TITLE POSI
** TITLE SETUP **
This parameter lets you select the position on the monitor screen where you want the title to be displayed.
1. Move the cursor to TITLE POSI.
2. Press one of the SELECT buttons (– or +). The
TITLE POSITION menu appears with the title of the
channel 1 on the monitor screen.
3. Select the position where the title is to be displayed
by pressing the CURSOR buttons (4 or 5).
4. Press the ESC button to return to the previous
menu.
CAM TITLE
TITLE SET *
TITLE POSI *
ALARM TITLE
ON
ON
** TITLE SETUP **
CAM TITLE
TITLE SET *
TITLE POSI *
ALARM TITLE
ON
OFF
ALARM
1.......
Note: All channel titles will be displayed in the
same position. You cannot specify a different
position for each title.
-11-
SYSTEM CONNECTIONS
SYSTEM 1
The input video signals for this unit are not synchronized.
VIDEO
VIDEO
VIDEO
VIDEO
WJ-MS424
OUT 4
IN
OUT 3
VIDEO
IN
OUT 2
IN
OUT 1
VTR
OUT
IN
VIDEO
OUT
ALARM/REMOTE
SIGNAL GND
Monitor
Monitor
VTR
Notes :
• When pressing the ALARM RESET/QUAD/SEQ/ECS button or the VIDEO SELECT/CURSOR/SELECT buttons, the picture on the video monitor may roll briefly at the time of switching.
• The video signal to be recorded by the VTR should be supplied from the VTR OUT connector of this unit and not from
the VIDEO OUT/ESC connector of this unit, unless VTR servo control disturbances are allowable when setting the
ALARM RESET/ QUAD/SEQ/ECS button or the VIDEO SELECT/CURSOR/SELECT buttons.
Connections
• Connect the VIDEO IN connectors of this unit to the video output connectors of the cameras.
• Connect the VTR OUT connector of this unit to the video input connector of the time lapse VTR for recording.
• Connect the VIDEO OUT connector of this unit to the video input connector of the video monitor.
-12-
SYSTEM 2
The input video signals for this unit are synchronized, and synchronization noise or disturbances in the video output signal
will not occur when the quad or single picture mode is selected.
GENLOCK
GENLOCK
GENLOCK
GENLOCK
VIDEO
VIDEO
VIDEO
VIDEO
WJ-MS424
OUT 4
IN
OUT 3
VIDEO
IN
OUT 2
IN
OUT 1
VTR
OUT
IN
VIDEO
OUT
ALARM/REMOTE
SIGNAL GND
VDA
Monitor
Monitor
VTR
Connections
• Connect the VIDEO IN connectors of this unit to the video output connectors of the cameras.
• Connect the VTR OUT connector of this unit to the video input connector of the video distribution amplifier (V.D.A).
• Connect the output of the video distribution amplifier (V.D.A.) to the video input connector of the time lapse VTR and to
the gen-lock input connectors of the cameras.
• Connect the VIDEO OUT connector of this unit to the video input connector of the monitor.
-13-
SYSTEM 3
A system consisting of this Quad Unit and the specified cameras should include the WV-PS104C Camera Drive Unit.
VIDEO
WV-PS104C
4ch
3ch
2ch
1ch
CAMERA VIDEO AUDIO CAMERA VIDEO AUDIO CAMERA VIDEO AUDIO CAMERA VIDEO AUDIO
IN
OUT
OUT
IN
OUT
OUT
IN
OUT
OUT
IN
OUT
OUT
VD/SYNC VD/SYNC
IN
OUT
CAUTION
(4Vp-p 75Ω)
WJ-MS424
OUT 4
IN
OUT 3
VIDEO
IN
OUT 2
IN
OUT 1
VTR
OUT
IN
VIDEO
OUT
ALARM/REMOTE
SIGNAL GND
Monitor
Monitor
VTR
Note: When pressing the ALARM RESET/QUAD/SEQ/ESC button or the VIDEO SELECT/CURSOR/SELECT buttons, the picture on the video monitor may roll briefly at the time of switching.
Connections
• Connect the VIDEO IN connectors of this unit to the video output connectors of the WV-PS104C Camera Drive Unit.
• Connect the VIDEO OUT connector of this unit to the video input connector of the monitor.
• Connect the VTR OUT connector of this unit to the video input connector of the time lapse VTR.
• Connect the video output connectors of the cameras to the camera input connectors of the WV-PS104C Camera Drive
Unit.
-14-
SYSTEM 4
Sensor
Sensor
Sensor
Sensor
WJ-MS424
OUT 4
IN
OUT 3
VIDEO
IN
OUT 2
IN
OUT 1
VTR
OUT
IN
VIDEO
OUT
ALARM/REMOTE
SIGNAL GND
Monitor
Monitor
VTR
Connections
• Connect the VIDEO IN connectors of this unit to the video output connectors of the cameras.
• Connect the VTR OUT connector of this unit to the input connector of the time lapse VTR.
• Connect the VIDEO OUT connector of this unit to the input connector of the monitor.
• Connect the wires of the alarm sensors to the alarm input pins of ALARM/REMOTE connector.
• Connect the ALARM OUTPUT pin of the ALARM/REMOTE connector of this unit to the alarm input terminal of the time
lapse VTR.
• Connect the recover output (alarm reset output) of the time lapse VTR to the ALARM RECOVER IN pin of the ALARM/
REMOTE connector of this unit.
• Connect the ALARM RESET OUT pin of the ALARM/REMOTE connector of this unit to the alarm reset in terminal of the
time lapse VTR.
-15-
SPECIFICATIONS
Video Input :
Video Output :
Title :
Alarm Input :
Alarm Output :
Alarm Time :
Recover Input :
Auto Reset Time :
Ambient Operating Temperature :
Power Source and
Power Consumption:
Dimensions :
Weight :
2:1 interlace, composite 1V [p-p] 75 Ω, auto termination or loop-through, black and white or
colour video signal x 4 (Each video signal should be synchronized vertically for vertical
interval switching. Does not have to be synchronized in case vertical interval switching
is not required.)
Video Output x 1, composite, 1V [p-p] 75 Ω, colour or black and white video signal with composite sync and burst signal.
Up to 8 characters per window
One per 4 video inputs (max. DC 12V and a make-contact for ground)
One (max. DC 24V, 100mA, open collector circuit)
Adjustable approx. 1s to 30s, 1, 2, 3, 4, 5 min. or EXT
One (max. DC 12V and a make-contact for ground)
Adjustable approx. 1s to 30s, 1, 2, 3, 4, 5 min. or OFF
−10˚C to +50˚C (14˚F to 122˚F)
220 - 240V AC, 50Hz, 14W
420 (W) x 44 (H) x 350 (D) mm
[16-1/2” (W) x 1-3/4” (H) x 13-3/4” (D)]
3.6 kg (7.9 lbs.)
Weight and Dimensions shown above are approximate.
Specifications are subject to change without notice.
STANDARD ACCESSORIES
Rack Mounting Brackets ................................................1 set
Rack Mounting Bracket Fixing Screws ..........................8 pcs
Switch Protector .............................................................1 pc
-16-
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
N0398-1048
YWV8QA4909BN
N 30
Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Impreso en Japón
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement