Panasonic WVCP110 Operating Instructions

Panasonic WVCP110 Operating Instructions
Colour CCTV Camera
WV-CP110E
Before attempting to connect or operate this product,
please read these instructions carefully.
N0499-0
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK), NO USER SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
YWV8QA5181AN
Printed in Japan
N 30
We declare under our sole responsibility that the
product to which this declaration relates is in conformity with the standards or other normative documents
following the provisions of Directive EEC/89/336.
Dichiariamo sotto nostra esclusiva responsabilità che
il prodotto a cui si riferisce la presente dichiarazione è
conforme agli standard o altri documenti normativi
ottemperanti alle disposizioni della direttiva CEE/89/
336.
Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet
aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijn
89/336/EEC.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is interned to alert the user to
the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
Vi erklærer os eneansvarlige for, at dette produkt,
som denne deklaration omhandler, er i overensstemmelse med standarder eller andre normative dokumenter i følge bestemmelserne i direktiv 89/336/EEC.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Ilmoitamme yksinomaisella vastuullamme, että tuote,
jota tämä ilmoitus koskee, noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja, jotka noudattavat direktiivin 89/336/EEC säädöksiä.
Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i
överensstämmelse med standarddokument, eller
andra normativa dokument som framstölls i EECdirektiv nr. 89/336.
Vi erklærer oss alene ansvarlige for at produktet som
denne erklæringen gjelder for, er i overensstemmelse
med følgende normer eller andre normgivende dokumenter som følger bestemmelsene i direktiv 89/336/
EEC.
The serial number of this product may be found on
the top of the unit.
You should note the serial number of this unit in the
space provided and retain this instruction as a permanent record of your purchase to aid identification
in the event of theft.
Model No.
Serial No.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
FEATURES
• Auto Light Control (ALC)/Electronic Light
Control (ELC)
• Automatic Gain Control (AGC) +15 dB and
Automatic Tracing White Balance (ATW)
• Minimum illumination of 0.6 lx (0.06 footcandle) at F0.75 [equivalent to 2.0 lx (0.2 footcandle) at F1.4]
•
•
•
•
Signal-to-noise ratio of 50 dB
Horizontal resolution of 480 lines
Built-in microphone
Easy connection with specified monitor by a
coaxial cable
PRECAUTIONS
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove
screws or covers.
There are no user serviceable parts inside.
Ask a qualified service person for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking,
shaking, etc. The camera could be damaged
by improper handling or storage.
3. Do not expose the camera to rain or
moisture, or try to operate it in wet areas.
Turn the power off immediately and ask a
qualified service person for servicing.
Moisture can damage the camera and also
create the danger of electric shock.
4. Do not use strong or abrasive detergents
when cleaning the camera body.
Use a dry cloth to clean the camera when
dirty.
In case the dirt is hard to remove, use a mild
detergent and wipe gently.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive
detergents. Use lens tissue or a cotton tipped
applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects.
Whether the camera is in use or not, never
aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may
be caused.
7. Do not operate the camera beyond the
specified temperature, humidity or power
source ratings.
Use the camera under conditions where temperature is between –10°C - +50°C (14°F 122°F), and humidity is below 90 %.
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
i
VIDEO
!0
r
t y
OUT
e
w
VOLUME
MIN
POWER
MAX
o
ALC
SOFT
OFF
OFF
ALC
SOFT
OFF
OFF
u
q
!5
!6
ELC
SHARP
BLC ON
MIC ON
!1
!2
!3
!4
ELC
SHARP
BLC ON
MIC ON
q Camera Mounting Bracket
Install on the wall or ceiling. See INSTALLING
PROCEDURE below.
w Pan Fixing Ring
Tighten after adjusting the pan angle.
e Pan Head
Attach the camera on this.
Rear Cover
r Auto Iris Lens Connector
Supplies power and DC control signals to an
auto iris lens (not supplied).
t Flange-back Adjusting Ring
This ring adjusts the back-focal distance or
picture focus.
y Lens (option)
u Camera Mounting Adapter
There is a hole for mounting the camera onto
a mounting bracket. The camera is originally
designed to be mounted from the bottom, but
a top-mounting type is also available. To
mount from the top, remove the mount
adapter from the bottom of the camera by
removing two fixing screws. Attach the mount
adapter to the top as shown in the diagram,
then mount the camera on the mounting
bracket. Make sure that two original screws
are used when mounting the mount adapter;
longer type screws may damage inner components.
i Video Output Jack (VIDEO OUT)
Connect this jack (φ2.5 mm mini jack) with the
control monitor to adjust or confirm settings
such as the pan angle or focus.
!2 Detail/Aperture Level Selector
(SOFT, SHARP)
The detail/aperture level can be selected with
this selector. Set it to the desired position
while observing the picture on the monitor.
SHARP: Normal position.
SOFT: Select this position when a Quad
System is connected to this camera.
!3 Back Light Compensation Mode Selector
(BLC ON, OFF)
Select the mode according to the position of
the object and light conditions.
ON: Select this mode when a strong light
such as a spotlight is in the background.
OFF: Normal picture.
!4 Microphone ON/OFF Selector
(MIC ON, OFF)
Select on or off according to need.
!5 Power Indicator (POWER)
Lights when power is supplied.
VIDEO OUT
VIDEO IN
POWER
ON
OFF
VIDEO OUT
!1 Automatic Light Control/Electronic Light
Control Selector (ALC, ELC)
Select the mode according to the lens type
that is used with this camera.
ALC: Select this mode when an auto iris lens
(ALC lens) is used with this camera.
ELC: Select this mode when a fixed iris lens
or manual iris lens is used with this camera.
Control Monitor
o Coaxial Cable Connector
Connect a coaxial cable (to be procured
locally) between this connector and the CAMERA IN connector of the specific monitor (or
Camera Drive Unit).
Monitor supplies power to the camera, and
the camera supplies the video and audio output to the monitor through the coaxial cable.
!0 Rear Cover
The rear cover can be removed to gain
access to the switches.
!65 Microphone Volume Control (VOLUME)
Adjust to prevent howling.
This control is preset in the Centre position at
the factory.
CONNECTIONS
Caution: Keep the POWER switch of the specified
monitor, Camera Extension Unit and Camera
Drive Unit in OFF position during connections. If the power of these units are ON during connections, the camera does not function due to protect circuit from misconnection.
• Basic System
Connect the single coaxial cables between
the Camera and Camera Input Terminal of
Specified monitor or Camera Drive Unit. The
approx. maximum cable length is as:
Coaxial
Cable
Type
Maximum
Cable
Length
RG-59/U
200 m (660 ft)
Caution:
Before you mount the lens, loosen the two
screws on the ring, and rotate this ring clockwise until it stops. If the ring is not at the end,
the inner glass or CCD image sensor may be
damaged.
q Mount the lens by turning it clockwise on the
lens mount of the camera.
w Connect the lens cable to the auto iris lens
connector on the side of the camera.
Screws
DC R/1 000 ft.
of Inner
Conductor
q
Less than
30 Ω
500 m (1 650 ft) Less than
12 Ω
RG-6/U
Mounting the Lens
w
Flange-back
Adjusting Ring
The maximum DC resistance between the
camera and these units is 20 Ω.
• Connection Diagram
Caution for Mounting the Lens
Video Monitor
WV-CM143
Coaxial
Cable
ALARM
CONTROL
SPOT MONITOR CONTROL IN
RECOVER GND 4
FOCUS
CAMERA
EXTENSION IN
3
2
1 STDBY ALL GND RESET 4
MODE
4
TIMING SELECT
OUT
IN
REMOTE OUT
3
2
1
AUDIO OUT AUDIO IN
VIDEO OUT VIDEO IN
CAMERA INPUT
3
2
1
CAMERA POWER
ON
OFF
The lens mount should be a C-mount or CS-mount
(1”-32UN) and the lens weight should be less than
450 g (0.99 lbs). If the lens is heavier, both the
lens and camera should be secured by using the
supporter.
The protrusion at the rear of the lens should be as
shown in the diagram.
Colour Video
Monitor
CS-mount: Less than 8 mm (5/16”)
Camera
Video
Caution: To use the C-mount lens, the Lens
Mount Converter (C-mount adapter) WV-
Audio
CAMERA
IN
CAUTION
VIDEO
OUT
AUDIO
OUT
VD/SYNC
IN
AD20 should be used with the camera.
VD/SYNC
OUT
SIGNAL
GND
USE WITH SPECIFIED EQUIPMENT SEE
ITS MANUAL BEFORE CONECTING.
Camera Drive Unit
WV-PS11B
FOCUS OR FLANGE-BACK ADJUSTMENT
The following adjustment should be made by
qualified service personnel or system installers.
w Turn the flange-back adjusting ring to the
desired position.
q Loosen the screws on the flange-back adjusting ring.
Caution: Do not rotate the ring counterclockwise by force after it stops. If the ring is
rotated by force, the inner lens or CCD
image sensor may be damaged.
w
e Tighten the screws on the flange-back adjusting ring.
qe
Flange-back
Adjusting Ring
Screws
INSTALLING PROCEDURE
The mounting bracket can be fixed either on the
top or the bottom cover of the camera.
When mounting on the top cover of the camera,
detach the mount adapter from the bottom of the
camera cover and attach it on the top cover of the
camera.
1. Fix the camera mounting bracket on the wall
or ceiling to be installed by two screws (to be
procured locally).
2. Insert the camera fixing screw on the pan
head into the camera mounting adapter, and
tighten the pan head firmly.
3. Connect the camera and the monitor with the
coaxial cable (to be procured locally).
Note: Coaxial cable can be passed through
the centre hole of the camera mounting
bracket.
Camera
Mounting
Bracket
Camera Mounting
Bracket
Fixing Screws
Coaxial Cable
DIMENSIONS OF MOUNTING BRACKET
Unit: mm (inch)
90°
164 (6-7/16)
5.5 (7/32)
15 (9/16) 85 (3-3/8) 40 (1-9/16)
83.5 (3-5/16)
φ120 (φ4-3/4)
Cautions on installation
Use wood screws with the camera mounting
bracket that are suitable for Installation into a
wood base of appropriate dimensions and
strength. For the installation into a material other
than wood, refer servicing to qualified service personnel.
2-φ5 (2-φ3/16)
SPECIFICATIONS
Pick-up Device:
Scanning Area:
Synchronization:
Scanning System:
Scanning:
Horizontal:
Vertical:
Horizontal Resolution:
Video Output:
Signal-to-Noise Ratio:
Electronic Light Control:
Minimum Illumination:
Detail:
Lens Mount:
Ambient Operating Temperature:
Ambient Operating Humidity:
Power Source:
Dimensions (without lens):
Weights (without lens):
752 (H) x 582 (V) pixels, Interline Transfer CCD
4.89 (H) x 3.67 (V) mm (Equivalent to scanning area of 1/3”
pick-up tube)
Multiplexed vertical drive (VD2) by pulse from specified camera
drive unit.
2 : 1 interlace
625 lines / 50 fields / 25 frames
15.625 kHz
50 Hz
480 lines
1.15 V[p-p] composite 75 Ω
50 dB (AGC OFF, weight ON)
Equivalent to continuous variable shutter speed between 1/50 s
and 1/15 000 s
0.6 lx (0.06 footcandle) at F0.75 [equivalent to 2.0 lx (0.2 footcandle) at F1.4]
SHARP or SOFT, selectable
CS-mount
−10°C - +50°C (14°F - 122°F)
Less than 90 %
From WV-PS11B/WV-PS104C
71 (W) x 65 (H) x 125.5 (D) mm
[2-25/32” (W) x 2-9/16” (H) x 4-15/16” (D)]
0.46 kg (1.02 lbs)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
STANDARD ACCESSORIES
Body Cap....................................................................................1 pc.
Camera Mounting Bracket ........................................................ 1 pc.
OPTIONAL ACCESSORIES
Lenses : WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3,
WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LFY3C3, WV-LFY45C3,
WV-LFY9C3
Lens Mount Converter (C-mount Adapter):
WV-AD20
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement