Panasonic WVPS11B Operating Instructions

Panasonic WVPS11B Operating Instructions
Camera Drive Unit
WV-PS11B
Before attempting to connect or operate this product,
please read these instructions completely.
ENGLISH VERSION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK), NO USER SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the
appliance.
For U.K.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your
safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement
fuse has a rating of 13 amp and that it is approved by ASTA or BSI to
BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement
cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic
Dealer.
H
G
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET
OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED
AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT
OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown
below.
If in any doubt please consult a qualified electrician.
WARNING: This apparatus must be earthed.
The serial number of this product may be found on the bottom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of
your purchase to aid identification in the event of theft.
Model No.
Serial No.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Caution:
Before attempting to connect or operate this product,
please read the label on the bottom.
For U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following
code.
Green-and-yellow:
Earth
Blue:
Neutral
Brown:
Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected to
the terminal in the plug which is marked with the letter E or by the earth
symbol I or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal in
the plug which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
in the plug which is marked with the letter L or coloured red.
We declare under our sole responsibility that the product to
which this declaration relates is in conformity with the standards or other normative documents following the provisions of
Directives EEC/73/23 and EEC/89/336.
Noi dichiariamo sotto nostra esclusiva responsabilità che il
prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi
alle disposizioni delle direttive CEE/73/23 e CEE/89/336.
Wij verklaren als enige aansprakelijke, dat het product waarop
deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de
bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC.
How to replace the fuse
Open the fuse compartment with
a screwdriver and replace the fuse
and fuse cover.
Vi erklærer os eneansvarlige for, at dette produkt, som denne
deklaration omhandler, er i overensstemmelse med den
følgende standarder eller andre normative dokumenter i følge
bestemmelserne i direktivene 73/23/EEC og 89/336/EEC.
For Australia
THIS APPARATUS MUST BE EARTHED.
To ensure safe operation the three-pin plug supplied must be inserted
only into a standard three-pin power point which is effectively earthed
through the normal household wiring. Extension cords used with the
equipment must be three-core and be correctly wired to provide connection to earth. Wrongly wired extension cords are a major cause of
fatalities.
The fact that the equipment operates satisfactorily does not imply that
the power point is earthed and that the installation is completely safe.
For your safety, if in any doubt about the effective earthing of the power
point, consult a qualified electrician.
Vi deklarerar härmed värt fulla ansvar för att den produkt till
vilken denna deklaration hänvisar är i överensstämmelse med
standarddokument, eller andra normativa dokument som
framstölls i Direktiv 73/23/EEC och 89/336/EEC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä
ilmoitus koskee, noudattaa seuraavia standardeja tai muita
ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC
ia 89/336/EEC. säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som denne
erklæringen gjelder for, er i overensstemmelse med følgende
normer eller andre normgivende dokumenter som fælger
bestemmelsene i direktiven 73/23/EEC og 89/336/EEC.
-1-
CONTENTS
PREFACE
PREFACE ..................................................................... 2
FEATURES ................................................................... 2
PRECAUTIONS ............................................................ 3
MAJOR OPERATING COMPONENTS
AND THEIR FUNCTIONS ............................................. 4
CONNECTIONS ........................................................... 5
SPECIFICATIONS ........................................................ 9
The Panasonic Camera Drive Unit WV-PS11B is specially designed to drive specified cameras such as WVBP70 or WV-CP100.
This simple system is specially designed for surveillance and security needs at offices, factories, schools,
hospitals, public or residential buildings, etc.
FEATURES
• Stable DC power is supplied to the specified camera by a regulator in the camera drive unit.
• A single coaxial cable connects the specified camera and camera input of the camera drive unit.
• Three signals, video, DC power and vertical drive
pulses, are carried by a single coaxial cable (used
with the WV-BP70 or WV-CP100 camera.).
• Audio signals can be transmitted from the specified camera to the camera drive unit (used with the
WV-CP100 or WV-CF20 camera.).
• VD/SYNC input and output connectors for synchronizing in the parallel operation.
• Built-in protection circuit protects the appliance in
case of wrong connection.
-2-
PRECAUTIONS
• Do not drop any metallic parts through slots.
This action could damage the appliance permanently. Turn the power off immediately and refer
servicing to qualified service personnel.
• Use the appliance under conditions where temperatures are within –10°C - +50°C (14°F - 122°F), and
humidity is below 90%. The input power source is
220 - 240V AC 50 Hz.
Do not operate the appliance in an extreme environment where is out of its specified temperature or
humidity range, or power source ratings.
• Do not block the ventilation opening or slots on the
cover to prevent the appliance temperature from
rising.
• Do not attempt to disassemble the appliance.
To prevent electric shock, do not remove screws or
covers. There are no user-serviceable parts inside.
• Handle the appliance with care.
Do not abuse the appliance. Avoid striking, shaking, etc. It could be damaged by improper handling or storage.
• Do not expose the appliance to rain or moisture.
Avoid trying to operate it in wet areas.
Take immediate action if ever the unit becomes
wet. Turn the power off and refer servicing to qualified service personnel. Moisture can damage the
appliance, and cause danger due to electric
shock.
• Do not use strong or abrasive detergents when
cleaning the appliance body.
Use a dry cloth to clean the unit when dirty. In case
the dirt is hard to remove, use a mild detergent and
wipe gently.
-3-
MAJOR OPERATING COMPONENTS AND THEIR FUNCTIONS
POWER
CAMERA
IN
VIDEO
OUT
AUDIO
OUT
VD/SYNC
IN
VD/SYNC
OUT
ON
OFF
CAUTION
USE WITH SPECIFIED EQUIPMENT SEE
ITS MANUAL BEFORE CONECTING.
SIGNAL
GND
r Audio Output Connector (AUDIO OUT)
The audio signal of the specified camera is provided at this connector for input into the video monitor
(used with the WV-CF20 or WV-CP100 camera.).
q Power On/Off Switch (POWER, ON/OFF)
This switch is used to turn the camera drive unit
and connected specified camera power on or off.
The indicator lights up when the power of the camera drive unit is on.
t VD/SYNC Input Connector (VD/SYNC IN)
The VD (Vertical Drive) pulse or VS (Video Sync)
signal is supplied to this connector for synchronizing the system.
w Camera Input Connector (CAMERA IN)
This connector accepts either a colour or B/W composite video signal from the specified camera. It
also supplies DC power and vertical drive pulses
or synchronizing signals to the camera, and
receives video and audio signal from the camera.
y VD/SYNC Output Connector (VD/SYNC OUT)
The VD (Vertical Drive) pulse or VS (Video Sync)
signal is provided at this connector for synchronizing other system component.
e Video Output Connector (VIDEO OUT)
The video signal of the specified camera is provided at this connector for input into the video monitor.
-4-
CONNECTIONS
Cautions:
• Set the POWER switch of the camera drive unit to OFF (l) during connections. If the power of the camera drive
unit is ON during connections, the protection circuit that protects it in case of wrong connection will operate and
prevent the camera from functioning.
• Connect only a specified camera, WV-BP70, WV-CF20 or WV-CP100. If another camera is connected, the camera drive unit will not operate due to activation of the protection circuit.
<Single Camera>
Camera Drive Unit
WV-PS11B
CAMERA IN
CAMERA
IN
VIDEO
OUT
AUDIO
OUT
VD/SYNC
IN
Monitor
VD/SYNC
OUT
SIGNAL
GND
AUDIO OUT
VIDEO OUT
Camera
-5-
<Multi Camera System with External SYNC Operation>
Monitor
1
2
3
4
5
6
Camera Drive Unit
WV-PS11B
CAMERA IN
CAMERA
IN
VIDEO
OUT
AUDIO
OUT
VD/SYNC
IN
VD/SYNC
OUT
SIGNAL
GND
TL
VIDEO OUT
VTR
Camera
VD/SYNC
CAMERA IN
Monitor
CAMERA
IN
VIDEO
OUT
AUDIO
OUT
VD/SYNC
IN
VD/SYNC
OUT
SIGNAL
GND
Camera Drive Unit
WV-PS11B
VIDEO OUT
Camera
-6-
1. Connect the coaxial cable between the camera
and CAMERA IN connector of the camera drive
unit. The approximate maximum cable length is as
follows:
Coaxial
Cable Type
DC R/1000 ft. of
Inner Conductor
Maximum
Cable Length
RG-59/U
RG-6/U
Less than 30 Ω
Less than 12 Ω
200 m (660 ft.)
500 m (1,650 ft.)
Note:
If the length of the coaxial cable between the
camera drive unit and the video monitor
exceeds the distance shown in the above
table, a cable loss compensator should be
used between the camera drive unit and the
video monitor.
3. After connecting the specified camera to the camera drive unit, connect the audio cable between the
monitor and AUDIO OUT connector of the camera
drive unit.
The maximum DC resistance of the cable between
the camera and camera drive unit is 20 Ω.
External VD/SYNC Signal
2. Connect the coaxial cable between the video monitor and VIDEO OUT connector of the camera drive
unit. The approximate maximum cable length is as
follows:
Type of
coaxial cable
Recommended
Maximum
cable length
RG-59/U
(3C-2V)
RG-6/U
(5C-2V)
RG-11/U
(7C-2V)
(m)
250
500
600
(ft)
825
1,650
1,980
Signal Level
The VD/SYNC IN connector accepts the VD or VS synchronizing signal for external synchronization.
• VD: 4 V[p-p] / 75 Ω
-7-
• Composite Sync: 4 V[p-p] /75 Ω
Relation between VD/SYNC IN and VD/SYNC
OUT
The signal from the VD/SYNC OUT connector differs
according to the connected camera and the signal supplied to the VD/SYNC IN connector of this unit.
The signal supplied from VD/SYNC OUT is as folllows:
• VS: 1 V[p-p] /75 Ω
Accuracy of vertical signal
Vertical frequency: 50 Hz ± 0.0013 Hz
-8-
Signal to
VD/SYNC
IN
Connected
Camera
No signal
VD signal
Composite
signal
WV-BP70
or
WV-CP100
Composite
signal
VD signal
Composite
signal
SPECIFICATIONS
Power Source:
Power Consumption:
Camera Input:
Video Output:
Audio Output:
Camera Power Supply:
Maximum Distance to Camera:
220 - 240 V AC 50 Hz
Approx. 16 W
1.0 V[p-p] / 75 Ω, BNC Connector
1.0 V[p-p] / 75 Ω, BNC Connector
–10 dB / 600 Ω unbalanced, RCA pin jack
Regulated current multiplex method (310 mA)
Coaxial
DC R/1000 ft. of
Maximum
Cable Type
Inner Conductor
Cable Length
RG-59/U
RG-6/U
Maximum DC Resistance:
VD/SYNC Input:
VD/SYNC Output:
Ambient Operating Temperature:
Ambient Operating Humidity:
Dimensions:
Weight:
Less than 30 Ω
Less than 12 Ω
200 m (660 ft.)
500 m (1,650 ft.)
Between camera and camera drive unit: 20 Ω.
4.0 V[p-p] /75 Ω Negative going or VS 1 V[p-p] /75 Ω, BNC Connector
4.0 V[p-p] /75 Ω Negative going, BNC Connector
–10 °C – +50 °C (14 °F – 122 °F)
Less than 90 %
138 (W) X 44 (H) X 185(D) mm
5-7/16” (W) X 1-3/4” (H) X 7-5/16” (D)
1.3 kg (2.9 lbs.)
Weight and dimensions shown are approximate.
Specifications are subject to change without notice.
-9-
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
N1096-0
YWV8QA4374AN
N 19
Printed in Japan
Gedruckt in Japan
Imprimé au Japon
Impreso en Japón
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement