Panasonic CQ5330U Operating Instructions

Panasonic CQ5330U Operating Instructions
R
Heavy Duty CD player/weather Band Receiver
with CD changer Control/XM Radio Ready
CQ-5330U
Operating Instructions
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
APM
CD SCAN
2
3
4
RPT
RDM
5
6
TUNE
SEEK
SCAN
ILL
• Please read these instructions carefully before using this product and keep this manual for future reference.
Safety Information
The following applies only in the U.S.A.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK OR PRODUCT DAMAGE, DO NOT
EXPOSE THIS APPLIANCE TO RAIN,
SPLASHING, DRIPPING OR MOISTURE.
Part 15 of the FCC Rules
FCC Warning:
Any unauthorized changes or modifications to this
equipment would void the user's authority to operate
this device.
CAUTION:
PLEASE FOLLOW THE LAWS AND REGULATIONS
OF YOUR STATE, PROVINCE OR COUNTRY FOR
INSTALLATION OF THE UNIT.
Laser Products:
Wave length: 780 nm
Laser power: No hazardous radiation is emitted with
safety protection.
NOTICE:
This product contains lead in some components.
Disposal of these materials may be regulated in your
community due to environmental considerations.
For disposal or recycling information please contact
your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, AND ANNOYING INTERFERENCE, USE
ONLY THE INCLUDED COMPONENTS.
Find the model number and serial number on either the back or bottom of the unit. Please record them in the space
below and retain this booklet as a permanent record of your purchase to help with identification in case of theft.
MODEL NUMBER
DATE PURCHASED
2
CQ-5330U
CQ-5330U
SERIAL NUMBER
FROM
Panasonic welcomes you to our ever growing family of electronic product owners. We know that this product
will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical
engineering, manufactured with carefully selected components and assembled by people who take pride in
their work. Once you discover the quality, reliability, and value we have built into this product, you too will be
proud to be a member of our family.
❐ Use this product safely
When Driving
Disc Mechanism
Keep the volume level low enough to be aware of
road and traffic conditions.
Do not insert coins or any small objects. Keep
screwdrivers and other metallic objects away from
the disc mechanism and disc.
When Washing Your Car
Do not expose the product, including the speakers
and CDs, to water or excessive moisture. This could
cause electrical shorts, fire, or other damage.
Use Authorized Servicenters
Do not attempt to disassemble or adjust this
precision product. Please refer to the Servicenter list
included with this product for service assistance.
When Parked
Parking in direct sunlight can produce very high
temperatures inside your car. Give the interior a
chance to cool down before switching the unit on.
For Installation
The product should be installed in a horizontal
position with the front end up at a convenient angle,
but not more than 30˚.
Use the Proper Power Supply
This product is designed to operate with a 12 V DC,
negative ground battery system.
What is XM Satellite Radio?
XM Radio is broadcastiog over 120 digital channels of totally new music, news, sports and children's
programming direct to vehicle and homes via satellite and our extensive repeater network, which supplements the
satellite signal to ensure seamless transmission. The channels originate from XM's broadcast center, the world's
largest all-digital studio complex in Washington, DC, and uplink to our two (Boeing 702) satellites, These
satellites transmit the signal across the entire continental United States. Each satellite provides 18kw of total
power making them the two most powerful commercial satellites ever built, providing coast-to-coast coverage.
XM Satellite Radio is changing the way people listen to radio in the same way cable changed television.
Accessories
1. Operating Instructions ..................................................................................................1
2. Supplied Hardware.............................................................................1 set (➡ page 26)
3. Warranty Card...............................................................................................................1
3
CQ-5330U
Contents
Safety Information(Part 15 of the FCC Rules). . . . . . . . . . . . . . . . . Page 2
Use this product safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
❒ Power and Sound Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Power, volume, mute, loudness, display change, audio mode
(Bass/Treble/Balance/Fader)
❒ Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Initial time, time reset
❒ Alarm Time Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Initial alarm time, alarm time setting and reset, alarm operation,
alarm output volume selection
❒ Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Radio mode, band, manual tuning, seek tuning, preset station setting,
preset station calling, display change, direct memory
❒ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disc insert and playback, stop and disc eject, listening to a CD,
CD player mode, display change, track selection, track search,
direct track selection, random play, scan play, repeat play,pause
❒ CD changer control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Play, repeat, random, scan, error messages
Note: CD changer controls are applicable to units with optional CD changer
unit (sold separately)
❒ XM Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
XM Mode, Band, Channel Selection, Category Priority Setting and Selecting,
Manual Preset Memory. Preset Memory Calling, Display Change,
XM ID Confirmation, Error Display
❒ Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting tips, where to get service help
❒ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Care of the unit, notes on discs, notes on CD-Rs/RWs
❒ Speaker Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
❒ Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Installation hardware, overview, required tools dashboard specifications,
identify all leads, connect all leads, final installation, final checks,
preparation, to remove the unit
❒ Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cautions, wiring diagram
❒ Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4
CQ-5330U
FM
Power and Sound Controls
Power
Turn the key in the ignition until the
accessory indicator lights.
Power on: Press [PWR] (power).
Power off: Press [PWR] (power) again.
ACC
ON
Remote Control Signal Sensor
Point the remote control unit
(CA-RC 500U, option) at the
unit's sensor.
PWR
VOL
PUSH
CLK
ALM
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
BAND
BASS/TREB/BAL/FADER
Volume
Turn the knob clockwise to increase volume,
and counterclockwise to decrease volume.
APM
MUTE
DISC
1
CD SCAN
2
3
RPT
RDM
5
6
4
SCAN
TUNE
SEEK
ILL
Loudness
Press and hold [MUTE] (LOUD) for more
than 2 seconds to enhance bass and treble
tones when listening at low or medium
volume.
Volume level (0 to 40)
(default:18)
Press and hold [MUTE] (LOUD) for more
than 2 seconds again to deactivate when
listening at higher volumes.
Up
Down
Mute
Press [MUTE] to mute the sound completely.
Press [MUTE] again to cancel.
5
CQ-5330U
Power and Sound Controls (Continued)
Audio Modes
(Bass/Treble/Balance/Fader)
Note: If no operation takes place for more than 5
seconds in audio mode (2 seconds in
volume mode), the display returns to the
regular mode.
q Push [SEL] to select the audio mode.
Volume
Bass
Treble
Fader
Balance
push
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
CD SCAN
2
3
4
APM
Turn [VOL] (volume) clockwise or
w counterclockwise
to change each level.
Bass:
default : 0 dB
Adjustable range: –12 to +12 dB (by 3 dB step)
Treble:
default : 0 dB
Adjustable range: –12 to +12 dB (by 3 dB step)
Balance:
R (right speaker) or L (left speaker)
Adjustable range:
1 to 15 (by 1 step)
Balance center
(default)
Fader:
F (front speaker) or R (rear speaker)
Adjustable range:
1 to 15 (by 1 step)
6
CQ-5330U
Fader center
(default)
RPT
RDM
5
6
TUNE
SEEK
SCAN
ILL
Illumination Switching
Press [SCAN] (ILL) for more than 2 seconds
to switch the illumination color (green/amber).
Clock Setting
Selecting the Clock Display
The 12-hour system is used for the clock.
Press [CLK] (clock) to switch clock and alarm time
display both.
clock display
Initial Time
Alarm time display
“SET” is displayed when the clock is not adjusted.
Note: if no operation takes place for more than 5
seconds in alarm time, the display returns to the
clock display.
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
CD SCAN
2
3
APM
4
RPT
RDM
5
6
TUNE
SEEK
SCAN
ILL
[{ TUNE], [} TUNE]
(Hours, Minutes)
Time Setting
q Press and hold [CLK] (clock) and do not release
to set time. Display blinks and the time setting
mode is activated.
(blink.)
Hours
w Press [{] to set the hour.
(Hours set.)
Minutes
e Press [}] to set the minute.
(Minutes set.)
r Once the time has been set, release [CLK].
(End.)
Note: Press and hold [{ ] or [} ] to change
numbers rapidly.
Time Reset
When you want to reset the time, repeat steps q to
r.
Note: the current time will be displayed at all the
time even the power of the radio is turned off.
7
CQ-5330U
Alarm Time Setting
The 12-hour system is used for the clock.
Initial Alarm Time
Press and hold [ALM] (Alarm)
“AM 12:00” is displayed when the alarm is not adjusted.
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
CD SCAN
2
3
4
APM
Alarm Time Setting
q Press and hold [ALM] (Alarm) and do not
release to set alarm time. Display blinks and
the alarm time setting mode is activated.
(blink.)
Hours
w Press [{] to set the hour.
(Hours set.)
RPT
RDM
5
6
TUNE
SEEK
SCAN
ILL
[{ TUNE], [} TUNE]
(Hours, Minutes)
Alarm Operation
• Alarm is switched to ON or OFF each time [ALM] is pressed.
• When the alarm is switched to ON, the alarm will sound at the set
alarm time.
Turning off the Alarm Sound
The alarm will turn off automatically after 90 seconds. Otherwise,
press [ALM] once.
Alarm output Volume Selection
You can select ALARM VOL 1 (or VOL 2) by pressing [ALM] in
sequence and the display will show as follows.
Minutes
e Press [}] to set the minute.
a
a OFF
(Minutes set.)
r Once the alarm time has been set, release [ALM].
Note: Press and hold [{] or [}] to change
numbers rapidly.
Alarm Time Reset
When you want to reset the alarm time, repeat
steps q to r.
8
CQ-5330U
Cautions:
• Be careful not to set wrong alarm time, otherwise, the alarm
may sound while driving.
• If the alarm is set, be sure to check the set alarm time by
pressing [CLK].
• If volume is set at “0” level, the output volume will be muted.
(Even when ALARM is acting.)
Radio
q Radio Mode
Press [MODE] to change to the radio mode.
Radio
CD Player
a
c
CD Changer Control
a
( When a CD changer is connected )
( When CD disc loaded )
FM stereo indicator
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
CD SCAN
2
3
4
RPT
RDM
5
6
TUNE
SEEK
SCAN
APM
ILL
w Band
Press [BAND] to change the band.
e Scan
• Press [SCAN], each station will be scanned sequentially and the display
will blink for 5 seconds.
• Press [SCAN] again to stop scanning and the last station will continue to
broadcast.
r Manual Tuning
[}TUNE]: Higher frequency
[{TUNE]: Lower frequency
Seek Tuning
Press and hold for more than 0.5 seconds and release it.
[}TUNE]: Higher frequency
[{TUNE]: Lower frequency
Tuning will automatically stop when the next broadcast
station is received.
9
CQ-5330U
Radio (Continued)
Preset Station Setting
Up to 6 stations can be saved in each of the FM1, FM2
and AM preset station memories.
Note: Existing saved stations are overwritten with new
stations after following this procedure.
q Band
Press [BAND] to select a desired band.
(➡ page 9)
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
CD SCAN
2
3
4
RPT
RDM
5
6
APM
TUNE
SEEK
SCAN
ILL
Preset buttons from [1] to [6]
w Auto Preset Memory (APM)
Press and hold [BAND] (APM: auto preset memory) for more
than 2 seconds.
• The 6 stations with good reception will be automatically
saved in the memory under preset buttons from [1] to [6].
• Once set, the preset stations are sequentially scanned for 5
seconds each.
• Press [BAND] again to stop sequentially scan.
Manual Preset Memory
q Use manual or seek tuning to find a station. (➡ page 9)
w Press and hold one of the preset buttons from [1] to [6]
until the display blinks once.
Preset Station Calling
Press the corresponding preset button from [1]
to [6] to tune in a preset station.
10
CQ-5330U
blinks once
Caution: To ensure safety, never attempt to preset stations
while you are driving.
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
CD SCAN
2
3
4
RPT
RDM
5
6
APM
TUNE
SEEK
SCAN
ILL
Tuning in a Weather Band Station
• Press [BAND] to select WB (Weather Band). (a page 9)
• Press any of the buttons [1] to [6] to monitor the preset station.
WB
Weather Band Frequency (channel) Number
Note: The weather band (CH1-6) has been preset. CH7 is selected by
pressing [}] or [{].
Weather Band Stations
National Weather Radio Broadcasts from over 380 Iocations throughout the
U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information 24 hours
a day on one of the following frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 165.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Occasionally the frequency of an existing or planned station must be
changed because of unexpected radio frequency interfere with adjacent
NOAA weather Radio Stations and/or with other Government or
commercial Operations within the area. If you have a question concerning
NOAA Weather Radio, please contact your nearest National Weather
Service Office.
11
CQ-5330U
CD Player
Disc Insert and Playback
Disc insert
Playback will start automatically after the player recognized
the loaded disc as an ordinary music CD. (When a CD-R or
CD-RW which has CD-DA formatted data as the same as an
ordinary music CD is loaded, this player recognizes it as an
ordinary music CD.)
u (eject)
CQ-533
0U
“LOAd” will be displayed until the disc is loaded.
Label Side
Notes:
• Do not insert a disc when “DISC” indicator lights.
• The power will be turned on automatically when a disc is
loading.
Stop and Disc Eject
Press [u] (eject) to stop CD play and eject the disc.
During disc ejection, “CD EJECT” will be displayed.
Listening to a CD
Press [MODE] to change to the CD player mode.
Playback will start automatically when a disc is loaded.
( When CD disc loaded )
CD player
Radio
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
12
CQ-5330U
1
APM
CD SCAN
2
3
4
RPT
RDM
5
6
TUNE
SEEK
SCAN
ILL
Cautions:
• Only 5" (12 cm) CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit.
• This unit does not support CD text display.
• This unit does not support MP3 and WMA disc playback.
• Refer to page 23 about notes on CD-Rs/RWs.
• This unit is not designed for any 3" (8 cm) disc.
• If you insert an 3" (8 cm) disc and can not eject it, turn ACC of your car off once and turn it on again, then press
[u] (eject).
• Do not use irregular shaped discs.
• Do not use discs that have a seal or label attached.
• Do not insert foreign matter into the disc slot.
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
CD SCAN
2
3
4
RPT
RDM
5
6
APM
TUNE
SEEK
SCAN
ILL
Track Selection
Track Search
Press [2 TRACK]: Advance to the next track.
Press [1 TRACK]: Back to the beginning of the current
track.
Back to the previous track. (Press
twice.)
Press and hold...
[2 TRACK]: Fast forward
[1 TRACK]: Fast reverse
Release to resume the regular play.
Repeat play
Random play
Scan play
• Press [5] (RPT) .
The current track is repeated.
• Press [5] (RPT) again to cancel.
• Press [6] (RDM).
All the tracks are played in random order.
• Press [6] (RDM) again to cancel.
• Press [4] (CD SCAN).
The first 10 seconds of each track on the
disc are played in sequence.
• Press [4] (CD SCAN) again to cancel.
13
CQ-5330U
CD Changer Control
q CD Changer mode
While a disc magazine is inserted in the CD changer, press [MODE] to select CD changer mode.
Play starts from the first track.
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
BASS/TREB/BAL/FADER
1
CD SCAN
2
3
APM
w Disc Selection
[1] ({ DISC): Previous disc.
[2] (} DISC): Next disc.
e Track Selection
Press [TRACK 2] once to go to the next track. Press
repeatedly to step forward through all the tracks.
Press [TRACK 1] once to play from the beginning of the
current track, Press twice to play the previous track. Press
repeatedly to step backward through all the tracks.
Track Search
Press and hold [TRACK 2] or [TRACK 1] for more
than 0.5 seconds to activate fast forward or reverse through
a track. Release it to resume the normal CD play from that
position.
14
CQ-5330U
4
RPT
RDM
5
6
TUNE
SEEK
SCAN
ILL
Note:
CD changer functions are applicable to units with optional CD changer unit.
(sold separately)
Scan Play
(Tracks)
• Press [4] (CD SCAN). The track number blinks
and the first 10 seconds of each track on the
discs play in sequence.
• Press [4] (CD SCAN) again to cancel and
continue with the current track.
Scan Play
(Discs)
• Press and hold [4] (CD SCAN) for more than 2
seconds. The first track of all the discs in the
magazine is played for 10 seconds each and
Disc Number blinks.
• Press and hold [4] (CD SCAN) for more than 2
seconds again to cancel.
blinks
blinks
Repeat Play
(Tracks)
• Press [5] (RPT) to repeat the current track.
• Press [5] (RPT) again to cancel.
Repeat Play
(Discs)
• Press and hold [5] (RPT) for more than 2 blinks REP: Repeat lndicator
seconds to repeat the current disc.
• Press and hold [5] (RPT) for more than 2
seconds again to cancel.
Random Play
(Tracks)
• Press [6] (RDM) to random selection. Music is lights R: Random Indicator
played from all available CDs.
• Press [6] (RDM) again to cancel.
Random Play
(Discs)
• Press and hold [6] (RDM) for more than 2
seconds all the available tracks on the current blinks R: Random Indicator
disc play in a random sequence.
• Press and hold [6] (RDM) for more than 2
seconds again to cancel
lights REP: Repeat lndicator
❐ Remote Control
CA-RC500U (option)
15
CQ-5330U
XM Control
Preparation:
Connect the XM receiver (XM DIRECT MODEL:XM-RVR-D-001) to the Unit CQ-5330U.
XM satellite radio is available on a chargable basis.
q XM Mode
r Channel Scan
(When a XM receiver is connected.)
Press [MODE] to change to the XM mode.
CLK
PWR
ALM
VOL
PUSH
SEL / SAT
CQ-5330U
DISP
LOUD
MODE
MUTE
DISC
BAND
1
BASS/TREB/BAL/FADER
CD SCAN
2
3
4
RPT
RDM
5
6
APM
TUNE
SEEK
SCAN
ILL
[CATEGORY]
w Band
Press [SCAN], each channel
in ascending order will be
scanned sequentially and
the display will blink for 5
seconds.
Press [SCAN] again to stop
scamming and the last
channel will continue to
broadcast.
XM displays as follows, (Example)
Press [BAND].
Satellite Radio after 2 seconds
Indicator
e Channel Selection
Press [}]: Up
Press [{]: Down
Press and hold [}] or [{] for more than 2
seconds to change channels rapidly.
XM Band
Preset Number
Channel Number
after 5 seconds
Channel Name
Category Priority Setting and Selecting
• Push the knob [SEL] for more than 2 seconds.
(Push and hold)
(without operation during 2 seconds.)
(when category is set ON.)
(without operation during 5 seconds.)
category name
(when category is set OFF.)
(blinks)
turn right
(interdisplay for 2 seconds.)
turn left
16
CQ-5330U
• When the display shows “CAT ON”,
Press [2] (}): Up
Press [1] ({): Down
1
2
1
(without operation during 5 seconds.)
Category Name
2
Press [2] or [1].
(Receiving)
(Received)
Category Name
(interdisplay for 2 seconds.)
Push and hold the knob [SEL] for more than 2 seconds
to resume the normal display.
category on indicator
Notes:
CAT OFF: Every channel can be selected from every category.
CAT ON: Only channels in the current category can be selected.
Default: CAT OFF
Manual Preset Memory
Up to 6 channels each can be saved in the XM1, XM2 and XM3 preset station memories.
q Select a band and a channel.
BAND
TUNE
SEEK
w Press and hold [1] to [6] for more than 2 seconds to memorize.
1
2
3
4
5
6
• The channel number and the preset number blink once.
Note:
Existing saved channels are overwritten with new channels after the above procedure.
Preset memory Calling
q Select a band.
BAND
w Press [1] to [6].
1
2
3
4
5
6
Note:
When category is on category will be off after pressed any preset button [1] to [6].
17
CQ-5330U
XM Control (Continued)
Display Change
Press and hold [MODE] (DISP) for more than 2 seconds.
MODE
Channel name
(Press and hold)
(Reading artist name)
Artist name
(Reading song title)
song title
(Reading categry)
Category name
Note:
Display when there is no name/title or can not decode.
XM ID Confirmation
• Push and hold the knob [SEL] for more than 2 seconds and then push again during 2 seconds.
(Push and hold)
(Push)
Note:
If the ID number is 12345678 for example.
• Push the knob for more than 2 seconds to resume to the previous mode when displaying “RADIO ID” or ID number.
• You can also see ID number by selecting CH0.
Error display
XM ID is or communication fails, Press [MODE] to another mode.
18
CQ-5330U
Troubleshooting
Preliminary Steps
Check and take steps as described in the tables below.
If You Suspect Something Wrong
Immediately switch the power off.
Disconnect the power connector and check that there is
neither smoke nor heat from the unit before asking for
repairs. Never try to repair the unit by yourself because it
is dangerous to do so.
Cautions:
• Do not use the unit if it malfunctions or if there is
something wrong.
• Do not use the unit in irregular condition, for
example, without sound, or with smoke or foul
smell, which can cause ignition or electric shock.
Immediately stop using it and call the store where
you purchased it.
Troubleshooting Tips
❐ Common
Trouble
Cause/Step
Vehicle’s ignition switch is not on.
a Turn your vehicle’s ignition switch to ACC or ON.
Cables are not correctly connected.
a Connect cables correctly.
No power.
Powere connector is not correctly connected.
a Connect the power connector to the terminal that is always active.
Power connector is not correctly connected.
a Connect the power connector to your vehicle’s ACC source.
Grounding wire is not correctly connected.
a Connect the grounding wire to a metal part of the venicle.
Mute is set to ON.
a Set it to OFF.
No sound.
Cables are not correctly connected.
a Connect cables correctly.
Noise.
The ground lead is not connected properly.
a Connect the ground lead properly.
19
CQ-5330U
Troubleshooting (Continued)
❐ Radio
Trouble
Much noise in FM stereo
and monaural broadcasts.
Preset station is reset.
Cause/Step
Station is too far, or signals are too weak.
a Select other stations of higher signal level.
The radio antenna is not extended enough.
a Extend fully the radio antenna.
Battery cable is not correctly connected.
a Connect the battery cable to the terminal that is always active.
❐ CD
Trouble
Cause/Step
Disc is upside down.
a Place disc in the correct direction with the label side up.
Disc is in the CD
compartment but no
sound is made, or disc is
ejected automatically.
• Disc is dirty.
• Disc has scratches.
a Clean disc, referring to the section on “Notes on Discs”.
A disc that has data other than CD-DA type is loaded.
a Discs that have CD-DA type data should be used.
a The unit may not successfully playback a CD-R/RW that is made in
combination of writing software, a CD recorder (CD-R/RW drive) and a
disc which are incompatible one another. Refer to instructions for the
concerned devices for details.
Sound skips, bad sound
quality. (e.g. caused by
noise)
20
CQ-5330U
• Disc is dirty.
• Disc has scratches.
a Clean disc, referring to the section on “Notes on Discs”.
a The unit may not successfully playback a CD-R/RW that is made in
combination of writing software, a CD recorder (CD-R/RW drive) and a
disc which are incompatible one another. Refer to instructions for the
concerned devices for details.
❐ CD (Continued)
Trouble
Cause/Step
Mounting angle is over 30˚.
a Adjust mounting angle to less than 30˚.
Sound skips due to
vibration.
Instable mounting.
a Mount the unit securely with the mounting parts, referring to the
section on installation.
Disc is not ejected.
• Disc is defective.
• Mechanical trouble.
a Press [u] (eject). If normal operation is not restored, call the store
where you purchased the unit or the nearest Servicenter to ask for
repairs.
Time is counted but no
sound comes out.
The first track of a mix mode disc was reproduced. (Mix mode is a format in
which data except music is recorded on the first track and music data is
recorded on other than the first track in a session.)
a Playback music data recorded on other than the first track.
❐ Sound Setting
Trouble
No sound from left, right,
front, or rear speaker.
Left and right sounds are
reversed in stereo
listening.
Cause/Step
Left and right balance, or front and rear balance is off on one side.
a Adjust BAL/FAD as appropriate.
Cables are not correctly connected.
a Connect the cables correctly.
The right speaker wire is connected to the left speaker and the left speaker
wire to the right speaker.
a Connect the speaker wires to the correct ones.
❐ XM Control
Trouble
Cause/Step
Antenna
Antenna no connection
a Check the XM receiver's antenna.
No singl
No XM signal
a select a channel which can be received.
off air
No chanel service
a select a channel which can be received.
No info
The original channel cannot receive signal.
a select a channel which can be received.
XM non
Do not connect the XM receiver completely.
a Check the XM receiver's connections.
21
CQ-5330U
Troubleshooting (Continued)
Error Display Messages
❐ CD
Trouble
Cause/Step
Disc is dirty, or is upside down.
A disc that has data other than CD-DA type is loaded.
➡ Check the disc.
Disc has scratches.
➡ Check the disc.
No operation by some cause.
➡ If normal operation is not restored, call the store where you purchased
the unit or the nearest Servicenter to ask for repairs.
❐ CD changer
Disc is dirty, or is upside down.
➡ Select the next available compact disc. Check the disc.
Disc has scratches.
➡ Select the next available compact disc. Check the disc.
No operation by some cause.
➡ Eject the magazine. If failure persists, press the reset switch on the CD
changer. If normal operation is not restored yet, call the store where you
purchased the unit to the nearest panasonic servic center to ask for
repairs.
No disc in the changer (magazine)
➡ Insert discs into the changer (magazine).
22
CQ-5330U
Maintenance
Care of the Unit
❐ Cleaning this Unit
❐ Caution on Cleaning
Use a dry, soft cloth to wipe.
Never use solvents such as benzine, thinner as they
may mar the surface of the unit.
Notes on Discs
Do not play any ordinary music CDs with labels
other than this one.
How to hold the disc
• Do not touch the underside of the disc.
• Do not scratch the discs.
• Do not bend disc.
• When not in use, keep the disc in the case.
Label side
Do not use irregular shaped discs.
• Transparency discs maybe can not be played back
Do not leave discs on the following places:
• Direct sunlight
• Near car heaters
• Dirty, dusty and damp areas
• Seats and dashboards
Do not use irregular shaped discs.
<Right>
<Wrong>
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label in a heavy pen or
ballpoint pen stroke.
Notes on CD-Rs/RWs
• You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due to
their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
• CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them
inside a vehicle for extended periods may damage them and make playback impossible.
• The unit may not successfully play back a CD-R/RW that was made by the combination of writing software, a CD
recorder (CD-R/RW drive) and a disc if they are incompatible one another.
• This player cannot play the CD-R/RW discs if the session is not closed.
• This player cannot play the CD-R/RW discs which contains other than CD-DA data.
• Be sure to observe the instructions of CD-R/RW disc for handling it.
23
CQ-5330U
Speaker Connections
Caution: Please follow the instructions given below. Failure to do so will cause damage to the unit and speakers.
<Right>
L +
-
R+
-
(White)
+
-
(White
w/black stripe)
(Gray)
+
-
(Gray
w/black stripe)
• Use ungrounded speaker only.
• The maximum speaker input should be 37 W or more. (If used with the optional
power amplifier, the speaker input should be higher than the maximum amplifier
output.)
• The speaker impedance should be 4 - 8 Ω.
• This unit uses the BTCL circuit, so each speaker should be connected separately
using parallel vinyl insulated cords.
• The speaker cords and the power amplifier unit should be kept away (about 30 cm
apart) from the antenna and antenna extension cord.
<Wrong>
L +
-
+
-
L +
-
+
-
L +
-
+
+
-
-
Chassis
+
+
R -
-
+
R -
+
-
+
R -
+
+
-
-
Chassis
• Never connect the speaker cord to
the body of the car.
• Do not use a 3-wire type speaker
system having a common earth
lead.
• Do not connect more than one
speaker to one set of speaker
leads.
Product Servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized
Panasonic Servicenter. The product should be serviced only by a qualified technician.
Maintenance
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine
exterior cleaning. Never use benzine, thinner, or other solvents.
Caution
This product is designed without a fuse inside due to fuses already exist in your vehicle. We would recommend to use
fuses of the specified rating (10 A). Using fuses that exceed the prescribed capacity could cause this product to start
smoking, ignite or other malfunction.
If your vehicle is without the fuse or a circuit braker to protect this unit ,please your dealer add the specified fuse 10 A
or a circuit breaker at the BATTERY lead of your vehicle's harness. please see page 26 to find out where "BATTERY +
12 V" is for your dealer adding the fuse or the circuit breaker.
24
CQ-5330U
Installation Guide
WARNING
❐ This installation information is designed for experienced installers and is not
intended for non-technical individuals. It does not contain warnings or cautions of
potential dangers involved in attempting to install this product.
Any attempt to install this product in a vehicle by anyone other than a qualified
installer could cause damage to the electrical system and could result in serious
personal injury or death.
❐ If your vehicle is equipped with air bag and/or anti-theft systems, specific procedures
may be required for connection and disconnection of the battery to install this product.
Before attempting installation of this electronic component, contact your vehicle
dealer or manufacturer to determine the required procedure and strictly follow their
instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN
DAMAGE TO THE VEHICLE AND PERSONAL INJURY.
❐ Overview
This product should be installed by a professional.
However, if you plan to install this product yourself,
your first step is to decide where to install it. The
instructions in these pages will guide you through the
remaining steps:
(Please refer to the “WARNING” statement above.)
• Identify and label the car wires.
• Connect the vehicle wires to the wires of the power
connector.
• Install the unit in the dashboard.
• Check the operation of the unit.
…Keep for future reference in case the product needs
servicing.
• Installation Hardware…Needed for in-dash installation.
❐ Dashboard Specifications
Thickness Min. 3⁄16" (4.75 mm)
Max. 7⁄32" (5.56 mm)
23⁄32" (53 mm)
75⁄32" (182 mm)
If you encounter problems, please consult your nearest
professional installer.
Caution: This unit operates with a 12 V DC negative
ground auto battery system only. Do not attempt to
use it in any other system. Doing so could cause
serious damage.
Before you begin installation, look for the items which
are packed with your unit.
• Warranty Card…Fill this out promptly.
• Panasonic Servicenter List for Service Directory
25
CQ-5330U
Installation (Continued)
❐ Preparation
❐ Installation Hardware
Warning: If your vehicle is equipped with air bag
and/or anti-theft systems, specific procedures may
be required for connection and disconnection of the
battery to install this product.
Before attempting installation of this electronic
component, contact your vehicle dealer or
manufacturer to determine the required procedure
and strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT OF
AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE
AND PERSONAL INJURY.
No.
Item
Diagram
Q’ty
q
Mounting Collar*
1
w
Plain washer (5mmø)
2
e
Spring Washer (5mmø)
2
r
Hex. Nut (5mmø)
2
t
Rear Support Strap
1
battery
y
Hex. Bolt
(5mmø × 25 mm)
1
• Remove Mounting Collar q from the main unit
temporarily, which are already mounted at shipment.*
u
Toothed Lock Washer
(5mmø)
1
i
Removal Tool
(U-shaped)
2
o
Antenna Connector
1
• Disconnect the cable from the negative
terminal (see warning and caution below).
Caution: Various settings that have been stored in
the memory in other on-board equipment (vehicle
navigation etc.) may be lost if the battery terminals
are disconnected.
Therefore, we recommend to make a record of or to
back up the settings before disconnecting the
terminals.
After completing installation of the main unit, set the
equipment again according to the record.
(a) Using the rear support strap t
• Unit should be installed in a horizontal position with
the front end up at a convenient angle, but not more
than 30˚.
❐ Dashboard Installation
Installation Opening
This unit can be installed in any dashboard having an
opening as shown below. The dashboard should be
3/16” (4.75 mm) – 7/32” (5.56 mm) thick in order to be
able to support the unit.
(b) Using the rubber cushion (option)
Rubber cushion (option)
Rear support bracket
(provided on the vehicle)
Mounting bolt
(5 mmø)
q Mounting collar
26
CQ-5330U
Cautions:
• We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
• When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands
and fingers.
First complete the electrical connections, and then check them for correctness.(a page 29)
The included Mounting Collar q is designed specially for this unit. Do not use it to attach any other model.
1
Insert Mounting Collar q into the
dashboard, and bend the mounting tabs
out with a screwdriver.
The tabs to be bent vary depending on
the vehicle. To securely install the unit,
fully bend a number of the tabs so that
there is no rattling.
Example:
Tab
q Mounting
Collar
Power Connector
Mounting Holes
Mounting Bolt
2
Mounting springs (C)
3
Engage the Mounting
Springs (C) in the
mounting holes of the
Mounting Collar q
firmly.
Establish the rear connection of the unit.
After fixing Power Connector, fix the rear of the unit
to the vehicle body by either method (a) or (b)
shown in the previous page.
After installation reconnect the negative
(–) battery terminal.
Mounting
Hole
Mounting Spring
27
CQ-5330U
Installation (Continued)
To Remove the Unit from the vehicle's dashboard
Insert each Removal Tool i and pull.
i Removal Tool
(U-shaped)
Note: Do not lose Removal Tools. They will be needed to remove the unit from the vehicle's dashboard.
28
CQ-5330U
Electrical Connections
Cautions:
• This wiring information is for experienced technical individual, for safety reason, please your dealer wire this
connection.
• This product is designed to operate with a 12 V DC, negative ground battery system.
• To prevent damage to the unit, be sure to follow the connection diagram below.
• Do not insert the power connector into the unit until the wiring is completed.
• Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and
keep cable terminals free from touching any metal parts.
• Remember, if your vehicle has a drive computer or a navigation computer, the data of its memory maybe erased
when the battery terminals are disconnected.
❐ Wiring Diagram
XM control connector
CD changer / XM control connector
10 12
CD Receiver
CQ-5330U
9
11
7
5
8
Antenna
6
14 16
13 15
3
4
1
2
(Rear Side)
Detail of power connector
햺 Antenna Connector
Power Connector
ŏ The power connector does not come
along with the unit. If need, please
consult your dealer.
NO.
1
2
3
4
5
6
7
8
FUNCTION
BATTERY +12 V
GROUND
ůůůů
ůůůů
ůůůů
POWER +12 V ACC
ůůůů
ůůůů
NO.
9
10
11
12
13
14
15
16
FUNCTION
REAR SP R (–)
REAR SP R (+)
FRONT SP R (–)
FRONT SP R (+)
FRONT SP L (–)
FRONT SP L (+)
REAR SP L (–)
REAR SP L (+)
(Red) Accessory Power(ACC)
(+12V DC, negative ground
only)
ACC
Ground
(Black) Ground Lead
(Connect to a clean, bare
metallic part of your vehicle)
Battery
(Yellow) Battery Lead
(Connect to vehicle battery)
(Violet/Black)
(Gray/Black)
(White/Black)
(white)
Left Speaker
(Front)
(Gray)
Right Speaker
(Front)
(Green/Black)
(Green)
Left Speaker
(Rear)
(Violet)
Right Speaker
(Rear)
29
CQ-5330U
Electrical Connections (Continued)
❐ Upgrading the system (connect a XM receiver and the wired remote.)
Note:
For wiring, carefully read the operation instructions for the devices connected.
XM control connector
(2P connector)
CQ-5330U
XM control connector
(10P connector)
Wired Remote Connector
(8P connector)
APM/PRG
SEEK
VOL
TUNE
DISP UP
RC330U
PWR
DISP
BAND MODE
SEL
- SAT
Wired Remote
( CA-RC330U, option )
power
RCA (Red) R
R
audio out
L
FM out
antenna
R
contoroller/
head unit
RCA (White) L
8P DIN (Male)
Extension Cable for connecting the unit and the XM receiver.
XM ANT
30
CQ-5330U
XM RECEIVER
(XM-RVR-D-001)
ŏThe Extension cable does not come along with the unit,
if need, please consult your dealer.
❐ Upgrading the system (connect a CD changer and the wired remote.)
Note:
For wiring, carefully read the operation instructions for the devices connected.
XM control connector
(2P connector)
CQ-5330U
CD changer connector
(10P conncetor)
Wired Remote Connector
(8P connector)
APM/PRG
SEEK
VOL
TUNE
RC330U
PWR
DISP
BAND MODE
DISP UP
SEL
- SAT
Wired Remote
( CA-RC330U, option )
CD Changer (CD-DP880, option)
Extension Cable for connecting the unit and CD changer.
ŏThe Extension cable does not come along with the unit,
if need, please consult your dealer.
31
CQ-5330U
Specifications
❐ General
Power Supply:
Current consumption:
Maximum Power Output:
Tone adjustment range:
Bass:
Treble:
Power Output:
Suitable Speaker Impedance:
Dimensions (W × H × D):
Weight:
12 V DC (11 V-16 V) test Voltage 14.4 V, Negative ground
Less than 2.5 A (CD mode, 0.5 W 4-speaker)
37 W × 4 channels at 400 Hz, Volume Control maximum
± 12 dB at 100 Hz
± 12 dB at 10 kHz
18 W per channel into 4 ohms, 40 to 30 000 Hz at 3 % THD
4-8 Ω
7" × 1-15/16" × 6-1/10" (178 × 50 × 160 mm)
3 lbs. 12 oz (1.7k )
❐ FM Stereo Radio
Frequency Range:
Useable Sensitivity:
50 dB Quieting Sensitivity:
Frequency Response:
Alternate Channel Selectivity:
Stereo Separation:
Signal/Noise Ratio:
87.9-107.9 MHz
12 dBf. (1.1 µV/ 75 Ω, S/N 30 dB)
17 dBf. (1.8 µV/ 75 Ω)
30-15 000 Hz ±3 dB
75 dB
35 dB at 1 kHz
70 dB (Mono)
❐ AM Radio
Frequency range:
Usable sensitivity:
530 kHz–1 710 kHz
28 dB/µV (25 µV, S/N 20 dB)
❐ CD Player
Sampling Frequency:
DA Converter:
Error Correction System:
Pick-Up Type:
Light Source:
Wavalength:
Frequency Response:
Signal to Noise Ratio:
Total Harmonic Distortion:
Wow and Flutter:
Channel Separation:
32 times oversampling
MASH•1 bit/4 DAC System
Panasonic Super Decoding Algorithm
1-beam
Semiconductor laser
780 mm
20 - 20,000 Hz (±1 dB)
85 dB
0.01 % (1 kHz)
Below measurable limits
75 dB
Above specifications comply with EIA standards.
Note: Specifications and the design are subject to modification without notice due to improvements in technology.
32
CQ-5330U
MEMO
33
CQ-5330U
MEMO
34
CQ-5330U
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
YFM284C420ZA
TAMACO0204-0
Printed in Taiwan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement