Panasonic | CQC1120AN | Operating instructions | Panasonic CQC1100VN Operating Instructions

Clock Setting
Take the face plate with you when leaving the car.
● Only when “NO CT” appears in the step w below, set the clock.
This product is a class I laser product.
■ Remove the face plate
]TUNE[
q Pull the right side.
w Slide the left side.
Detach the face plate.
Put the face plate into the case.
Note: An alarm is generated to remind you of the face plate when turning off the
power.
Press [BAND] to select the
radio AM (MW/LW) mode.
(a Refer to “Radio”)
(AM mode)
Press [DISP].
(NO CT)
Hold down [DISP] for 2 seconds or more.
(Blink: Hours)
Press []TUNE[].
Adjust hours
Press [DISP].
(Blink: Minutes)
Press []TUNE[].
Adjust minutes
Press [DISP].
(Completed)
■ Install the face plate
q Slide the left side.
w Press the right side until a “click” is heard.
1
Precautions
■ Volume Level
For your driving safety, keep the volume level low enough to be aware of road and
traffic conditions.
■ Car Washing
To avoid electrical shorts which may cause fire, or other damage, do not expose
this product (including the speakers and CDs) to water or excessive moisture.
■ Car Ventilation
If your car is parked for several hours in direct sunlight, the temperature inside the
car may become very high. It is advisable to drive the car and give the interior a
chance to cool down before switching the unit on.
■ Power Supply
Operating
Instructions
Installation
Instructions
English
(YEFM284127)
Deutsch
(YEFM284128)
Français
(YEFM284129)
Nederlands
(YEFM284130)
Svenska
(YEFM284131)
Italiano
(YEFM284132)
Español
(YEFM284133)
Polski
(YEFM284134)
Q'ty: 1 set
English
Deutsch
Français
Nederlands
(YEFM293095)
3 General
No power
No sound
Noise
3 Radio
Frequent
noise
Preset data
deleted
Check point
● This unit does not support 8 cm discs.
● Do not touch the recorded surface.
● Avoid leaving CDs in places with direct sunlight, dust and
● Start the engine. (Or turn the ignition
switch to the ACC position.)
● Verify the wiring. (Ex. Battery cord, ACC
cord, grounding cord, etc.)
● Fuse blown (Contact the nearest
Panasonic Service Centre.)
● Ask a professional for fuse replacement.
● Be sure to use the same rated fuse.
● Disable the mute function.
● Verify the wiring.
● Wait until the dew disappears before
turning on the unit.
● Make sure that the ground lead is grounded properly.
3 CD Player (CONTINUED)
● The maximum permissible tilt is 30°.
Sound skip
due to vibra- ● Secure the unit.
tion
CD not
ejectable
● Press [u]. If the CD is not ejected, contact the nearest Panasonic Service
Centre.
No sound from ● Adjust the balance and fader.
left, right, front, ● Verify the wiring.
or rear speaker
Left and right
sounds are
reversed
is grounded properly.
● The preset memory is cleared to return to
the original factory setting when the power
connector or battery is disconnected.
● Connect the speaker cord correctly.
3 Error indication
Message
Cause
Remedy
No sound, or
● Load the CD correctly.
disc is automati- ● Clean the CD.
cally ejected
● Clean the CD.
Customer Care Centre
¡
¡
¡
¡
For UK customers: 08705 357357
For Republic of Ireland customers: 01 289 8333
Visit our website for product information
E-mail: customer.care@panasonic.co.uk
¡ Order accessory and consumable items for your product
with ease and confidence by phoning our Customer Care
Centre Monday - Friday 9:00am - 5:30pm. (Excluding
public holidays).
¡ Or go on line through our Internet Accessory ordering
application at www.panasonic.co.uk.
¡ Most major credit and debit cards accepted.
¡ All enquiries transactions and distribution facilities are
provided directly by Panasonic UK Ltd.
¡ It couldn't be simpler!
¡ Also available through our Internet is direct shopping for
a wide range of finished products, take a browse on our
website for further details.
● CD dirtied
● CD upside
down
Time is counted
● Not compatible with MP3/WMA.
but no sound
comes out.
Sales and Support Information
Direct Sales at Panasonic UK
3 Sound quality
● Tune in to another high-intensity station.
● Make sure that the antenna mounted point
3 CD Player
Sound skip,
poor sound
quality
moisture such as seat and dashboard.
● Do not use irregular shaped discs.
Check point
● Eject the CD.
● CD scratched
● No operation
by some
cause.
● Consult your nearest
Panasonic Service
Centre.
Product service, repair and enquiry
8 Consult your nearest Panasonic Service Centre.
Operating Instructions
Mounting
Collar
Power
Connector
(YEFX0215873)
Q'ty: 1
(YEAJ02874)
Q'ty: 1
i
The difference among these models are mentioned below.
8 All illustrations represent model CQ-C1120AN unless otherwise specified.
■ Disc Mechanism
Notes on discs
Trouble
(YEFA131646)
Q'ty: 1
8 This operating instruction manual applies to the 5 models below.
ISO Antenna
Adapter
Lock Cancel
Plate
● You may have trouble playing discs in the following cases.
Dirt, fingerprints, scratches on the disc surface
If a disc is damaged from leaving inside a car for extended periods, etc.
● Inappropriate writing software is used.
● Contains other than CD-DA data.
●
●
Mounting Bolt
(YEP0FZ3264)
Q'ty: 1 set
Models
CQ-C1120AN
CQ-C1120GN
CQ-C1110AN
CQ-C1110GN
CQ-C1100VN
Trim Plate
C1100VNL
(YEFC05613)
Others
(YEFC05609)
Q'ty: 1
Notes:
● The number in parenthesis underneath each accessory part name is the part number for
maintenance and service.
● Accessories and their parts numbers are subject to modification without prior notice due
to improvements.
● Mounting Collar t and Trim Plate i are mounted on the main unit at shipment.
Note: The preset memory is cleared to return to the original factory setting when the
power connector or battery is disconnected.
Something wrong....?! (Ex. smoke, smell and no sound B possibility of fire or shorting.)
q Turn off the power.
w Detach the power cord and bring the unit to your dealer.
CQ-C1120AN/C1120GN
C1110AN/C1110GN/C1100VN
Removable
Face
Plate Case
y
u
This product is made of precision parts. Do not attempt to disassemble or adjust
any parts. For repair, please consult your nearest authorized Panasonic Service
Centre.
● Never try repair by yourself.
Q'ty: 1
t
Svenska
Italiano
Español
Polski
(YEFM293096)
Q'ty: 1 set
■ Service
Troubleshooting
Warranty Card
This product is designed to be used in a car having a 12-Volt negative ground battery system.
Do not insert coins or any small objects. Keep screwdrivers and other metallic
objects away from the disc mechanism and disc.
Trouble
r
CD Player/Receiver
DISP
SQ
2
e
sonnel.
CQ-C1120AN
2
w
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
● Wave length : 780 nm
● Laser power : No hazardous radiation is emitted with safety protection.
0AN
1
q
● A laser beam leak results in hazardous radiation exposure.
● Do not open covers and do not repair it by yourself. Refer servicing to qualified per-
BAND
Release the face plate.
Accessories
Cautions
Notes on
CD-R/RW
Maintenance
● Wipe the unit with a soft dry cloth.
● Never apply volatile liquids such as benzine and thinner to
prevent damage.
Trim Plate Color
Dark Silver
Dark Silver
Dark Silver
Dark Silver
Coating Black
Matsushita Electric Industrial Co., Ltd.
Web Site : http://www.panasonic.co.jp/global/
YEFM284127
ND1203-1014
Printed in China
Thank you very much for purchasing a Panasonic CD Player/Receiver.
■ CD-R/CD-RW playable
■ New simple-setting tone control "SQ" (Sound Quality)
● Not compatible with MP3/WMA.
● You may have trouble playing back some CD-R/RW discs
recorded on CD recorders (CD-R/RW drives), either due to
their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
● CD-R/RW discs are less resistant to high temperatures and
high humidity than ordinary music CDs. Leaving them
inside a car for extended periods may damage and make
playback impossible.
● Some CD-R/RWs can not be played back successfully
thanks to incompatibility among writing software, a CD
recorder (CD-R/RW drive) and the discs.
● This player cannot play the CD-R/RW discs if the session is
not closed.
● This player cannot play the CD-R/RW discs which contains
other than CD-DA.
● Be sure to observe the instructions of CD-R/RW disc for
handling it.
Face Color Face Illumination Color Button Illumination Color
Plating Silver
Amber
Amber
Plating Silver
Green
Green
Plating Black
Amber
Amber
Plating Black
Green
Green
Coating Black
Blue
Red
■ 2.5 V preamplifier outputs
■ 18 FM and 6 AM presets with preset scan
Fuse
■ Anti-theft system provided by the removable faceplate
● Use fuses of the same specified rating (15A).
● Using different substitutes or fuses with higher ratings, or
connecting the unit directly without a fuse, could cause fire
or damage to the unit.
● If the fuse replacement fails, contact your nearest
authorized Panasonic Service Centre.
Fantastic
Sound Space!
Subwoofer (For Upgrade)
Sophisticated Product Achieived by Optional Functions
●Sound System with Spurting Realism
(2-channel or 4-channel Power Amplifier)
●Powerful Heavy Bass
(Stereo/Mono Power Amplifier) : CY-M7052EN/CY-M9054EN
Specifications
■ General
■ CD Player
Power Supply
Sampling Frequency
Pick-Up Type
Light Source
Wavelength
Frequency Response
Signal to Noise Ratio
Total Harmonic Distortion
Wow and Flutter
Channel Separation
: 12 V DC(11 V - 16 V), Test
Voltage 14.4 V, Negative
Ground
Tone Controls (Bass)
: ±12 dB at 100 Hz
Tone Controls (Treble)
: ±12 dB at 10 kHz
Current Consumption
: Less than 2.5 A (CD mode, 0.5
W 4-Speaker)
Maximum Power Output
: 45 W x 4 (at 4 Ω)
Power Output
: 20 W x 4 (DIN45 324, at 4 Ω)
Speaker Impedance
:4-8Ω
Pre-Amp Output Voltage
: 2.5 V (CD mode)
Pre-Amp Output Impedance : 200 Ω
Dimensions (Main Unit)
: 178(W) x 50(H) x 155(D) mm
Weight (Main Unit)
: 1.4 kg
English
Theft Prevention
■ Radio
: 8 times oversampling
: Astigma 3-beam
: Semiconductor laser
: 780 nm
: 20 Hz - 20 kHz (1 dB)
: 96 dB
: 0.01 % (1 kHz)
: Below measurable limits
: 75 dB
FM
Frequency Range
Usable Sensitivity
Stereo Separation
MW
Frequency Range
Usable Sensitivity
LW
Frequency Range
Usable Sensitivity
: 87.5 - 108 MHz
: 6 dB/µV(S/N 30 dB)
: 35 dB (at 1 kHz)
: 531 - 1 602 kHz
: 28 dB/µV (S/N 20 dB)
: 153 - 279 kHz
: 32 dB/µV (S/N 20 dB)
Note: Specifications and design are subject to modification without notice due to improvements.
Stereo/Mono Power Amplifier:
CY-M7052EN/CY-M9054EN
(For Upgrade)
CQ-C1120AN/C1120GN/
C1110AN/C1110GN/
C1100VN
How to Enjoy Music
BAND/APM (Auto Preset Memory)/
y/5 (Pause)
CD Slot
FM1
1
2
PTY (Programme Type)/
MONO/LOC(Local)
]TUNE[
6 TRACK 7
Eject
Fast Forward/Fast Reverse
Press to select a band.
FM2
FM3
■ Seek tuning
AM (LW/MW)
Hold down for 0.5 seconds or more.
Tuning will automatically stop when the next station is found.
[[]: higher frequency
[]]: lower frequency
Mono: Reduce noise if weak signals are received
Local: Only strong signals of stations are searched for in seek tuning.
■ FM broadcast
Hold down [PTY] (MONO/LOCAL) for 2 seconds or more to
change the mode.
■ Manual Tuning
CQ-C1120AN
Mono/Local Selection
[[]: higher frequency
■ AM(LW/MW) broadcast
[]]: lower frequency
Press [PTY] (MONO/LOCAL) to change the mode.
Preset Memory
LOCAL indicator
SRC (Source)/
POWER
TA (Traffic Announcement)
MUTE/SQ (Sound Quality)
Band
the same program is tuned in automatically.
DISP (Display)/CT (Clock Time)
Radio
Power on
Hold down for 2 seconds or more.
● Automatically tune the 6 stations with good reception and
Press to select a mode as follows.
FM broadcast
AM(LW/MW) broadcast
save under preset buttons [1] to [6].
● Press again and hold to power off.
● Preset stations appear for 5 seconds each.
Radio
CD Player
DISP
■ Auto Preset Memory
Enjoy music in each mode
● Press to power on.
MONO indicator
Notes:
● Only RDS stations will be saved at default setting (AF is
ON).
● To stop scanning, press one of the preset buttons [1] to
[6].
When a disc is loaded.
MONO OFF/LOCAL OFF
LOCAL OFF
MONO ON/LOCAL OFF
LOCAL ON
■ Manual Preset Memory
Display Change
Use seek or manual tuning to find a station.
Sound Controls
Press
(3 seconds)
Frequency
this procedure.
■ Preset station calling
Turn to adjust
Clock Time
Press [1] to [6] to call a preset station.
■ Sound Control
■ Sound Quality (SQ)
Press and hold [MUTE] (SQ) for more than 2 seconds to select
the sound type as follows:
● Available Discs
does not emphasize.
Bass
Treble
(0 to 40)
(–12 to +12 in 2 dB step)
Balance
(left/right: 1 to 15)
Fader
(front/rear: 1 to 15)
Note: If no operation takes place for 5 seconds or more (2 seconds in the volume
mode), the display return to the regular mode.
■ Mute
Press to switch on and off.
● Mute the sound completely.
CD-RW
(VOCAL) : clear sound:
emphasizes middle tone and
slightly emphasizes treble.
Notes:
● If no operation takes place for more than 5 seconds in the SQ mode, the
display returns to the regular mode.
● Settings of SQ, bass/treble are influenced one another. If the influence
mentioned above causes distortion to audio signal, readjust bass/treble
or volume.
WMA
MP3
Insert a disc and playback starts automatically.
: wide-ranged and deep sound:
slightly emphasizes bass and
treble.
8 cm
■ When a disc is not loaded
exaggerates bass and treble.
(POP)
● Non-available
This unit does not support CD text display.
(ROCK) : speedy and heavy sound:
(–12 to +12 in 2 dB step)
■ Track selection and track search
Only discs with the label at right are available.
(default) : flat frequency response:
Turn to change each level
Volume
● Stations can be selected by program type, for example,
TA indicator
news and rock.
TP indicator
PTY indicator
Lights up while receiving a TP
station
tion is received.
● If a preset station is in poor receiving condition, another station in good receiving condition can be tuned in
to by pressing the same preset button. (Best Station
Research)
● Another station broadcasting the same program is
searched for if a station with an appropriate frequency
cannot be found even by means of BSR (Best Stations
Research). (PI seek: Program Identification Seek)
a Press [PTY].
● To cancel
aPress [PTY] again.
■ PTY preset call
another station giving traffic announcements will be
automatically tuned in.
● When TA ON is selected, only TP station will be
searched. When TA ON is selected, only TP station will
be memorized automatically.
● Even in CD player mode, a station giving the traffic
information is automatically received.
a Hold down [TA] for 2 seconds or more (in FM
mode).
● To cancel
a Press [TA] again. (Or, raise the volume with
[VOL]).
■ TA Volume Set (Volume Level: 1 to 40)
a Turn [VOL] while receiving traffic announcements.
● The TA volume differs from the regular volume (by up
to 5 levels).
Down
■ To select mode PTY
Up
a Press [1] to [6].
● The following program types are preseted.
Preset No. Program Type Contents
1
NEWS
NEWS
AFFAIRS, INFO, EDUCATE,
2
SPEECH
DRAMA, CULTURES, SCIENCE,
VARIED, WEATHER, FINANCE,
CHILDREN, SOCIAL A,
RELIGION, PHONE IN, TRAVEL,
LEISURE, DOCUMENT
3
SPORT
SPORT
4
POP M
POP M
5
CLASSICS
CLASSICS
6
MUSIC
ROCK M, M_O_R_M, LIGHT M,
OTHER M, JAZZ, COUNTRY,
NATIONAL, OLDIES, FOLK M
■ PTY selection
q Press []TUNE[] to select a program type
below.
w Press [BAND] for automatic selection.
SPEECH
INFO
CULTURES
ROCK M
OTHER M
SOCIAL A
LEISURE
OLDIES
MUSIC
SPORT
SCIENCE
M_O_R_ M
WEATHER
RELIGION
JAZZ
FOLK M
NEWS
EDUCATE
VARIED
LIGHT M
FINANCE
PHONE IN
COUNTRY
DOCUMENT
AFFAIRS
DRAMA
POP M
CLASSICS
CHILDREN
TRAVEL
NATIONAL
■ PTY preset change
EON
q Select a program type by using PTY selection
or PTY preset call.
Enhanced Other Networks
● Traffic information of the other networks is received.
● Preset AF data is refreshed at all times.
w Hold down [1] to [6] for 2 seconds or more.
Note: When there is no corresponding program type,
“NO PTY” is displayed.
■ Emergency Announcement
● An emergency announcement, if broadcast, is automat-
ically received.
● This function operates in other than the radio mode,
and “ALARM” flashes.
Note: Press [DISP] to switch the PTY display language
Note: For PI Seek, cancel the TA mode first, then execute PI Seek.
to Swedish.
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music type.
Press to select a mode
2
Note: A station name appears when it is an RDS station.
Caution: Never preset stations while driving.
(The program may be different) (Default)
● The memory is valid for the RDS stations only.
● A station of the same network in good receiving condi-
Hold down one of the preset buttons [1] to [6] until
the display blinks once.
Note: New stations overwrite existing saved stations after following
a Press [AF]
AF1 : For mountain areas and places enclosed by highrise buildings or other objects that prevent radio
reception. (Default)
AF2 : For suburbs and other places free of obstructions
of view.
OFF : For the AF function inactivated.
■ AF1 or AF2 auto preset memory
Program Service Name
■ Volume Adjustment (Setting range: 0 to 40)
■ To select AF receiving sensitivity
a Hold down [AF] for 2 seconds or more.
● REGION ON : To select a station broadcasting the
same program
● REGION OFF : To select an AF station of the same network
MONO OFF/LOCAL ON
● To automatically listen to a station
■ To listen to TA only
AF indicator
■ To change AF range
MONO ON/LOCAL ON
Program Type
Notes:
● If a selected station is in poor receiving condition,
● When reception is poor, an RDS station broadcasting
Preset Number
Traffic Announcements
a Press [TA].
(Default : TA OFF)
8 To cancel a Press [TA] again.
Alternative frequency
Frequency
PTY
■ To select TA mode
AF (Alternative Frequency)/
REG (Region)
VOLUME/SEL (Select)
1
RDS is a system performing convenient functions for
FM stations in such as Europe. However, there may be
some areas where RDS is not effective for reception.
AF
Press to select a band for
preparation.
1 to 6 (Preset Memory)
Radio Data
System (RDS)
PTY (MONO/LOC)
CQ-C1120AN
TA
that gives traffic information periodically.
● Station name appears instead of the frequency.
● The clock is automatically adjusted.
● Up to 6 stations can be stored in each of the FM1, FM2, FM3 and
AM (LW/MW) band selections.
SQ
Convenient
Function
● Next track:
[7] Press
● Start of current track:
[6] Press once
● Previous track:
[6] Press twice
● Fast forward:
[7] Hold down
● Fast reverse:
[6] Hold down
Display Change
Press
Playing Variation
CQ-C1120AN
Track Number/Playing Time
Random indicator
Repeat indicator
Release it to resume regular CD play.
SQ
CD
Player
■ Pause
Clock Time
Press [BAND] (h/5) to pause. Press again to resume to playback.
Disc indicator
Make sure that the disc indicator is off before loading a
disc.
If the disc indicator lights, eject the disc, then load a new
disc.
● It takes several seconds between the instant when inserting a CD and the
■ Disc Eject
Press [u] to stop CD play and eject the disc.
■ RANDOM
● Random play
Press [4]. R5
lights.
■ SCAN
● 10 seconds play of each track.
Press [5].
instant when starting playback.
● Do not use discs that have a seal or label attached.
● Do not insert foreign matter into the disc slots.
● Press again to cancel in each play mode.
■ REPEAT
● Repeat play
Press [6]. REP lights.
Download PDF

advertising