Panasonic CQC1110W, CQC1100W Operating instructions

Panasonic CQC1110W, CQC1100W Operating instructions
General
Power
Display change
Turn the key in the ignition
until the accessory indicator lights.
Power on: Press [SRC]
(POWER).
Power off: Press [SRC]
(POWER) again
and hold.
Press [DISP] (display) to switch to the clock display.
When the power is off:
No display
Clock display
Note: Please refer to next page when “AdJ” is displayed.
Bass
Regular mode
Treble
Fader
Balance
4
q Press [DISP] (CLOCK).
Push [SEL] to select the audio mode.
Volume
Initial time
Clock setting
Audio mode
(Bass/Treble/Balance/Fader)
q
The 24-hour system is used for the clock.
E
N
G
L
I
S
H
“AdJ” is displayed when the clock is not adjusted.
push
[k TUNE], [l TUNE] (Hours, minutes)
Remote control sensor (➡ page 19)
(only for CQ-C1110W: CQ-C1100W has no remote control function.)
ACC
ON
UME / PUSH SE
L
CQ-C1110W
BA
ND
VO L
D•M
APM
TUNE
TRACK
CLOCK
POWER
D•M
MUTE
7
8
1
2
9
3
10
11
12
4
5
6
SCAN
SQ
ND
CQ-C1110W
RA
UME / PUSH SE
L
C
SR
VO L
ND
3
Note: If no operation takes place for more than 5 seconds
in audio mode (2 seconds in volume mode), the display
returns to the regular mode.
BA
E
N
G
L
I
S
H
REP
OM
DI
SP
APM
TUNE
TRACK
CLOCK
POWER
1
2
9
3
10
4
11
5
12
6
SCAN
SQ
ND
MUTE
MUTE
8
RA
C
SR
7
REP
OM
DI
SP
[DISP] (CLOCK)
w Turn [VOLUME] clockwise to increase volume,
and counterclockwise to decrease volume.
SQ indicator
Bass:
Volume
SQ (Sound Quality)
Turn [VOLUME] clockwise to increase
volume, and counterclockwise to
decrease volume.
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
type.
Press [SQ] to select a sound type as follows:
Up
Down
Mute
Adjustable range: –12 dB to +12 dB (by 2 dB step)
SQ -- (default)
flat frequency response:
does not emphasize.
SQ - 1 (ROCK)
speedy and heavy sound:
exaggerates bass and treble.
SQ - 2 (POP)
wide-ranged and deep sound:
slightly emphasizes bass and treble.
SQ - 3 (VOCAL)
clear sound:
emphasizes middle tone and
slightly emphasizes treble.
ST
Notes:
• If no operation takes place for more than 2 seconds in the SQ mode, the display returns to the regular mode.
• Settings of SQ, bass/treble are influenced one another. If the influence mentioned above causes distortion to audio
signal, readjust bass/treble or volume (➡ page 7).
6
CQ-C1110W/C1100W
(Hours set.)
(default: 0 dB)
Minutes
r Press [DISP] (CLOCK).
(Minutes blink.)
R (right speaker) or L (left speaker)
MUTE
Press [MUTE] again or turn the knob clockwise
to cancel.
e Press [k TUNE] or [l TUNE].
Treble:
Balance:
(default)
Press [MUTE] to mute the sound completely.
Mute indicator
(Hours blink.)
(default: 0 dB)
Adjustable range: –12 dB to +12 dB (by 2 dB step)
Volume level (0 to 40)
(default: 18)
Hours
w Press and hold [DISP] (CLOCK) for more than
2 seconds.
t Press [k TUNE] or [l TUNE].
Adjustable range: 1 to 15 (by 1 step)
(Minutes set.)
Balance center
(default)
Fader:
y Press [DISP] (CLOCK).
F (front speaker) or R (rear speaker)
Adjustable range: 1 to 15 (by 1 step)
Fader center
(default)
Note: If the fader is set to front, the pre-amp.
output (rear) is decreased.
(End.)
Note: Press and hold [k TUNE] or [l TUNE] to
change numbers rapidly.
Time reset
Press and hold [DISP] (CLOCK) for more than
2 seconds to activate the time setting mode to
reset the time.
Then, repeat steps e to y.
CQ-C1110W/C1100W
7
E
N
G
L
I
S
H
Caution: To ensure safety, never attempt to preset
stations while you are driving.
Preset station setting
Display change
E
N
G
L
I
S
H
Up to 6 stations each can be saved in the FM1, FM2,
FM3 and AM preset station memories.
Press [DISP] (display) to switch to the clock display.
6
Radio
mode
Radio
Press [SRC] (source) to change to the radio mode.
5
CD player
Radio
FM Stereo indicator
Note: Existing saved stations are overwritten with
new stations after following this procedure.
UME / PUSH SE
L
q Band
CQ-C1110W
BBAA
NN DD
VO L
DD• •M
M
APM
Press [BAND] to select a desired band. (➡ page 8)
TUNE
TRACK
LOCA
ST MONO
POWER
1
2
9
3
10
11
12
4
5
6
CLOCK
SCAN
SQ
ND
8
RA
RCC
SSR
MUTE
7
Clock display
Frequency
OM
REP
DI
SP
Band
UME / PUSH SE
L
CQ-C1110W
BBAA
NN DD
VO L
D•M
APM
Press [BAND] to change the band.
TUNE
TRACK
8
11
22
9
33
10
11
12
44
55
66
CLOCK
SCAN
SQ
ND
MUTE
7
RA
C
SR
tuning
Manual
[l TUNE]: Higher frequency
LOCA
ST MONO
POWER
OM
REP
SSPP
DDI I
Preset station calling
[k TUNE]: Lower frequency
Seek tuning
Press and hold ...
[l TUNE]: Higher frequency
[k TUNE]: Lower frequency
Tuning will automatically stop when the signals of the next broadcast station are received.
Direct Memory (D·M)
Your favorite FM/AM radio station can be memorized in the [D·M] button and you can call back radio stations
just by pressing the button whatever the current sound source is, even if the power is off.
Press the corresponding preset button from [1] to
[6] to tune in a preset station.
w Auto Preset Memory (APM)
Press and hold [BAND] (APM: auto preset memory) for more than 2 seconds.
• The 6 stations with good reception will be automatically saved in the memory
under preset buttons from [1] to [6].
• Once set, the preset stations are sequentially scanned for 5 seconds each.
Default : FM 87.5 MHz
Recalling the direct memory
Press [D·M]. (Press again to cancel)
¡The direct memoried station is received.
Memorize
Select the station in Radio mode (➡ above)
D-M
Press and hold [D·M] until the Frequency display blinks.
D-M
Manual preset memory
Use manual or seek tuning to find a station.
(➡ page 8)
Press and hold one of the preset buttons
from [1] to [6] until the display blinks once.
blinks once
D·M indicator
D-M
blinks
e Release [D·M] button. Then, new station will be overwritten on existing saved station.
D-M
8
CQ-C1110W/C1100W
CQ-C1110W/C1100W
9
E
N
G
L
I
S
H
E
N
G
L
I
S
H
CD player
Disc insert and playback
[u] (eject)
7
Playback will start automatically after the player recognized the
loaded disc as an ordinary music CD. (When a CD-R or CD-RW
which has CD-DA formatted data as the same as an ordinary music
CD is loaded, this player recognizes it as an ordinary music CD.)
“LOAd” will be displayed until the disc is loaded.
Label side
Caution:
• Only 12 cm CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit.
• This unit does not support CD text display.
• This unit does not support MP3/WMA disc playback.
• Refer to page 24 about notes on CD-Rs/RWs.
• This unit is not designed for any 8 cm disc.
• If you insert an 8 cm disc and can not eject it, turn ACC of your car off once and turn it on again, then
press [u] (eject).
• Do not use irregular shaped discs.
• Do not use discs that have a seal or label attached.
• Do not insert foreign matter into the disc slot.
Direct track
selection
Pause (y/ 5)
Notes:
• Do not insert a disc when DISC indicator lights.
• The power will be turned on automatically when a disc is loaded.
Press [BAND] (y/ 5) to pause.
Press [BAND] (y/ 5) again to resume
the playback.
Repeat playC2
Random playC3
Stop and disc eject
Press [u] (eject) to stop CD play and eject the disc.
During disc ejection, “EJ” (eject) will be displayed.
UME / PUSH SE
L
CQ-C1110W
BA
ND
VO L
D•M
APM
TUNE
TRACK
Listening to a CD
CD player mode
<CD player display>
Track playing time
7
8
1
2
9
3
10
11
12
4
5
6
SCAN
ND
CD player
MUTE
RA
C
SR
<Disc indicator> DISC
• lights when the disc is loaded.
• Do not insert a disc when “DISC”
indicator lights.
Press [SRC] (source) to change to the CD play mode.
Playback will start automatically.
Radio
CLOCK
POWER
SQ
OM
REP
DI
SP
Track selection
Track search
[d TRACK]: Advance to the next track.
[s TRACK]: Back to the beginning of the current track.
Back to the previous track. (Press twice.)
Press and hold ...
[d TRACK]: Fast forward
[s TRACK]: Fast backward
Release to resume the regular play.
Scan playC1
BA
ND
CQ-C1110W
D•M
APM
TUNE
TRACK
DISC
TRACK
CLOCK
POWER
1
2
9
3
10
11
12
4
5
6
SCAN
SQ
ND
8
RA
RCC
SSR
MUTE
7
OM
REP
Press [DISP] (display) to switch to the clock display.
DISC
DISC
TRACK
Playing time Track number
10
CQ-C1110W/C1100W
TRACK
Clock display
• Press and hold [SQ] (SCAN),for more than 2
seconds.
The first 10 seconds of each track on the disc
are played in sequence.
• Press and hold [SQ] (SCAN) again to cancel.
DISC
TRACK
blinks
SSPP
DDI I
Repeat
playC2
Display change
• Press a track number button
from [1] to [6].
The corresponding track starts
playing.
• Press and hold a track number
button from [1] to [6] ([7] to
[12]) for more than 2 seconds.
The corresponding track starts
playing.
Scan PlayC1
Track number
UME / PUSH SE
VO L
L
8
Random
playC3
• Press [REP].
The current track is repeated.
• Press [REP] again to cancel.
• Press and hold [REP] (RANDOM) for more
than 2 seconds.
All the tracks are played in random order.
• Press and hold [REP] (RANDOM) again to
cancel.
REP: Repeat indicator
REP
DISC
TRACK
R 5 : Random indicator
R
DISC
TRACK
CQ-C1110W/C1100W
11
E
N
G
L
I
S
H
9
Installation
Anti-Theft system
This unit is equipped with a removable face plate. Removing this face plate makes the radio totally inoperable.
q Remove the removable
face plate
Installation hardware
Preparation
• Before installation, check the radio operation with
antenna and speakers.
• Disconnect the cable from the negative (–) battery terminal (see caution below).
• Unit should be installed in a horizontal position with the
front end up at a convenient angle, but not more than
30°.
• Remove Mounting Collar q and Trim Plate u from
the main unit temporarily, which are already mounted
at shipment*.
Contact
Switch off the power of the unit.
Release button
qPress [
]. The removable face plate will be
opened.
w Push the face plate to
either the right or left.
e Pull it out toward you. M
w
q Press
30˚ or less
w Place the removable
face plate into case
q Gently press the bottom of the case and
open the cover. Place the face plate into
the case and take it with you when you
leave the car.
Caution: Various settings that have been stored
in the memory in other on-board equipment (car
navigation etc.) may be lost if the battery terminals are disconnected.
Therefore, we recommend to make a record of
or to back up the settings before disconnecting
the terminals.
After completing installation of the main unit,
set the equipment again according to the record.
Removable face plate case
Dashboard installation
fInstall the removable face
plate
q Slide the left side of the removable face plate in
place.
w Press the right end of the removable face plate
until “click” is heard.
w
Tab
q
Cutout
Caution:
• This face plate is not waterproof. Do not expose it to water or excessive moisture.
• Do not remove the face plate while driving your car.
• Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level.
• Do not touch the contacts on the face plate or the main unit, since this may result in poor electrical contacts.
• If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.
12
CQ-C1110W/C1100W
E
N
G
L
I
S
H
No.
Item
Diagram
10
Q’ty
q
Mounting Collar*
(FX0214C316ZA)
1
w
Hex. Nut (5 mmø)
(YJN994C002ZA)
1
e
Rear Support Strap
(YFG044C002ZA)
1
r
Tapping Screw (5 mmø×16 mm)
(XTT5+16AFK)
1
t
Mounting Bolt (5 mmø)
(YEJV014C002A)
1
y
Power Connector
(YEAJ02877)
1
u
Trim Plate*
C1110W: (YFC054C058ZA)
C1100W: (YFC054C057ZA)
1
i
Dismounting Plate
(YFX214C323ZA)
2
(a) Using the Rear Support Strap
53 mm
Installation opening
182 mm
The unit can be installed
in any dashboard having an opening as shown at right.
The dashboard should be 4.5 mm - 6 mm thick in
order to be able to support the unit.
Installation precautions
This product should be installed by a professional
installer, if possible.
In case of difficulty, please consult your nearest authorized Panasonic Service Center.
1. This system is to be used only in a 12 V, DC battery
system (car) with negative ground.
2. Follow the electrical connections carefully
(➡ page 16). Failure to do so may result in damage
to the unit.
3. Connect the power lead (red) after all other connections are made.
4. Be sure to connect the battery lead (yellow) to the
positive terminal (+) of the battery or fuse block
(BAT) terminal.
5. Insulate all exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
7. Please carefully read the operating and installation
instructions of the respective equipment before connecting it to this unit.
r Tapping Screw
Fire Wall of Car
3 mmø
w Hex. Nut
e Rear Support Strap
t Mounting Bolt
q Mounting Collar
(b) Using the Rubber Cushion (option)
Rear Support Bracket
(Provided on the car)
Rubber Cushion
(Option)
t Mounting Bolt
q Mounting Collar
CQ-C1110W/C1100W
13
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Installation (Continued)
Cautions:
• We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
• When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your
hands and fingers.
11
First complete the electrical connections, and then
check them for correctness. (➡ page 16)
The included Mounting Collar
q is designed specially for
this unit. Do not use it to
attach any other model.
1
Insert Mounting Collar q into the
dashboard, and bend the mounting
tabs out with a screwdriver.
The tabs to be bent vary depending on the
car. To securely install the unit, fully bend
a number of the tabs so that there is no
rattling.
Tab
Example:
IMPORTANT
When this unit is installed
in dashboard, ensure that
there is sufficient air flow
around the unit to prevent
damage from overheating,
do not block any ventilation
holes on the unit.
To Remove the unit
Switch off the power of the unit.
q Remove the Removable
Contact
12
Release button
Face Plate.
qPress [
]. The removable face plate will be
M
opened.
w Push the face plate to
either the right or left.
e Pull it out toward you.
w
w
q Press
Remove the Trim Plate u with a screwdriver.
u Trim Plate
Screwdriver
q Mounting
Collar
1
2
y Power Connector
e
Mounting Holes
t Mounting Bolt
2
Mounting Springs (C)
Engage the both sides
Mounting Springs
(C) in the mounting
holes of the Mounting
Collar q firmly.
Mounting
Hole
3
4
qInsert the Dismounting Plate i along
the grooves on both sides of the main
unit until “click” is heard.
wPull out the unit while pushing the plates
further inside.
Insert the tab
end in the
outer groove.
Establish the rear connection of the
unit.
After fixing Mounting Bolt t and insert the
Power Connector y, fix the rear of the unit to
the car body by either method (a) or (b) shown
on the previous page.
i Dismounting Plate
wPull out
Insert Trim Plate u.
After installation reconnect the negative (–) battery terminal.
qInsert
“Click”
r
Remove the unit pulling with both hands.
Mounting Spring
14
CQ-C1110W/C1100W
CQ-C1110W/C1100W
15
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Electrical connections
Caution:
• This product is designed to operate with a 12 V DC, negative ground battery system.
• To prevent damage to the unit, be sure to follow the connection diagram below.
• Strip about 5mm of the lead ends for connection.
• Do not insert the power connector into the unit until the wiring is completed.
• Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all
cables and keep cable terminals free from touching any metal parts.
• Remember, if your car has a drive computer or a navigation computer, the data of its memory may be
erased when the battery terminals are disconnected.
13
System up
speakers
14
External Power Amplifier
CY-M7052
(option)
R (Red)
L (White)
CQ-C1110W/C1100W
RCA Cord
(option)
L (White)
R (Red)
L (White)
R (Red)
Fuse (15 A) C
Antenna
6 Power Connector
Preamp output connector (rear)
Ground lead
To a clean, bare metallic
part of car chassis.
Motor antenna
relay control lead
(To motor antenna)
(Max. 500 mA)
This lead is not intended
for use with switch actuated
power antenna.
(Yellow)
(Dark blue)
(Red)
ACC
(Dark blue/white stripe)
Note: The power antenna extends
automatically when turning on the
power of this unit.
(White)
(+)
Left speaker
(Front)
16
(Gray/black
stripe)
(–)
(Gray)
(+)
Right speaker
(Front)
CQ-C1110W/C1100W
REAR SP
(Green/black
stripe)
(–)
(Green) (Violet/black
stripe)
(+)
Left speaker
(Rear)
Battery lead
To the car battery, continuous +12 V DC
(–)
(Violet)
(+)
Right speaker
(Rear)
Control power extension lead
(option )
Power lead
To ACC power, +12 V DC
Amp. relay control power lead
(Max. 500 mA)
This lead is for connection to the power
amplifier.
Speaker lead
FRONT SP
(White/
black
stripe) (–)
BATTERY 15A
(Black)
Note: This lead is used for power
control when an external power
amplifier is connected. The power
supply of a power amplifier will be
activated when turning on the power of
this unit.
C If the fuse (rear panel) blows frequently, they may be something
wrong with the unit or wiring.
Consult your nearest Panasonic
Service center for service.
To remove the Fuse
Fuse
Note:
1
• Use the optional extension lead to extend
the Amp. relay control power lead if needed.
• The extension lead should be soldered and 6
Power
insulated with the vinyl tape.
connector
CQ-C1110W/C1100W
3
2
17
Only for CQ-C1110W
Speaker connections
Remote control unit
Battery installation
Caution: Please follow the instructions given below. Failure to do so will cause damage to the unit and
speakers.
15
<Right>
L +
-
R+
-
(White)
+
-
(White
w/black stripe)
(Gray)
+
-
(Gray
w/black stripe)
• Use ungrounded speaker only.
• The maximum speaker input should be 45 W or more. (If used with the
optional power amplifier, the speaker input should be higher than the maximum amplifier output.)
• The speaker impedance should be 4 - 8 Ω.
• This unit uses the BTCL circuit, so each speaker should be connected separately using parallel vinyl insulated cords.
• The speaker cords and the power amplifier unit should be kept away (about 30
cm apart) from the antenna and antenna extension cord.
<Wrong>
L +
-
+
-
L +
-
E
N
G
L
I
S
H
+
-
L +
-
+
+
-
-
q Remove the battery holder.
Pull the battery holder by the position B while pushing
position A in the direction indicated by the arrow.
w Install the battery on the battery holder.
Place a battery in the holder with its “+” side facing up
as shown in the figure.
e Insert the battery holder.
Push the battery holder back into its original position.
Lithium battery
w
Position B
e
Battery holder
Position A
Battery notes
16
Back side
q
Remove and dispose of an old battery immediately.
Battery Information:
• Battery type: Panasonic lithium battery (CR2025)
• Battery life: Approximately 6 months with normal use (at room temperature)
Chassis
+
+
R -
-
+
R -
+
-
+
R -
+
+
-
-
Caution: Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a
fire.
Chassis
• Never connect the speaker cord
to the body of the car.
• Do not use a 3-wire type speaker system having a common
earth lead.
• Do not connect more than one
speaker to one set of speaker
leads (except for connecting to
a tweeter).
• Do not disassemble or short the battery. Do not throw a battery into a fire.
• Keep batteries away from children to avoid the risk of accidents.
• Be careful to observe proper local disposal rules when you dispose of batteries.
Control reference guide
Buttons of the remote control function in the same way as the controls on the main unit of the reference page.
Point the remote control unit at the main unit’s sensor.
Fuse
PWR
[MODE]
(Mode (source))
(➡ pages 8, 10)
[BAND]
(Band) (Pause)
(➡ page 8, 11)
VO L
UME / PUSH SE
L
ND
(ATT)
MUTE
MODE
VOL
PRG
[MUTE]
(Mute)
(➡ page 6)
[j VOL] [i VOL]
(Volume )
(➡ page 6)
APM
POWER
C
SR
Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher ratings, or connecting the unit directly without a fuse, could cause fire or damage to the unit.
If the fuse replacement fails, contact your nearest authorized Panasonic Service Center.
[PWR]
(Power)
(➡ page 6)
BA
E
N
G
L
I
S
H
7
MUTE
1
BAND/DISC UP
TUNE
TRACK
Car Audio
[k TUNE] [l TUNE]
[a TRACK] [f TRACK]
(Tune/track selection/track search)
(➡ pages 8, 11)
Note: CQ-C1100W has no remote control function.
18
CQ-C1110W/C1100W
CQ-C1110W/C1100W
19
E
N
G
L
I
S
H
17
E
N
G
L
I
S
H
Troubleshooting
If you suspect something wrong
Immediately switch the power off.
Disconnect the power connector and check that there is neither
smoke nor heat from the unit before asking for repairs. Never
try to repair the unit by yourself because it is dangerous to do
so.
Troubleshooting tips
Caution:
• Do not use the unit if it malfunctions or if
there is something wrong.
• Do not use the unit in irregular condition,
for example, without sound, or with
smoke or foul smell, which can cause
ignition or electric shock. Immediately
stop using it and call the store where you
purchased it.
❐ Radio
Problem
Poor reception or
noise
Possible cause ➡ Possible solution
Sound is not
generated.
Fuse blowout
➡Eliminate the cause of fuse blowout and replace the fuse with new one.
Consult your dealer.
The number of receivable stations is less than 6.
➡Move to an area where receivable stations number is maximum,
and try presetting.
Preset stations cannot
be stored.
The contact of the battery lead is poor, or the battery lead is not always
powered.
➡Make sure that the battery lead is connected securely, and preset
stations again.
MUTE is set to ON.
➡Set MUTE to OFF.
The wiring of the speaker lines are not correct, or a break or poor contact arises.
➡Check the wiring in accordance with the wiring diagram.
❐ CD
Problem
There is an electromagnetic-wave generator such as a cellular phone near the
unit or its electrical lines.
➡Keep an electromagnetic-wave generator such as a cellular phone away
from the unit and the wiring of the unit. In case that noise cannot be eliminated due to the wiring harness of the car, consult your dealer.
Noise
20
No playback or disc
ejected
The contact of the ground lead is poor.
➡Make sure that the ground lead is connected to an unpainted part of the
chassis securely.
Sound skipping or
noise
Noise is made in step
with engine revolutions.
Alternator noise comes from the car.
➡ Change the wiring position of the ground lead.
➡ Mount a noise filter on the power supply.
Sound skipping due to
vibration
Some operations are
not executable.
Some operations are not executable in particular modes such as menu mode.
➡Read the operating instructions carefully and cancel the mode. In case the
unit is still out of order, consult your dealer.
No sound from speaker(s)
BAL/FAd setting is not appropriate.
➡ Readjust BAL/FAd.
The speaker wiring is confused between right and left.
➡ Perform the speaker wiring in accordance with the wiring diagram.
The sound field is not
clear in the stereo
mode. Central sound
is not settled.
The plus and minus terminals at right and left channels of speakers are connected reversely.
➡ Perform the speaker wiring in accordance with the wiring diagram.
Possible cause ➡ Possible solution
The disc is inserted upside down.
➡Insert a disc correctly.
There is a flaw or foreign material on the disc.
➡Remove the foreign material, or use a flawless disc.
There is a flaw or foreign material on the disc.
➡Remove the foreign material, or use a flawless disc.
The unit is not sufficiently secured.
➡Secure the unit to the console box with the rear support strap, etc.
The unit is tilted at over 30˚ in the front-to-end direction.
➡Make the angle 30˚ or less.
A label is peeled off from the CD in the unit.
➡Refer repair to the dealer where you purchased the unit.
Disc unejectable
There is a break, a short circuit, poor contact or wrong wiring regarding the
speaker wiring.
➡ Check the speaker wiring.
The speaker channels
are reversed between
right and left.
CQ-C1110W/C1100W
Antenna installation or wiring of antenna cable is faulty.
➡Check whether the antenna mounting position and its wiring are correct. In addition, check to see whether the antenna ground is
securely connected to the chassis.
The number of auto
preset stations is less
than 6.
The power cord (battery, ACC and ground) is connected in the wrong way.
➡Check the wiring.
No power to the unit
18
No power is supplied to the antenna amplifier (when using a film antenna, etc.).
➡Check the wiring of the antenna battery lead.
❐ Common
Problem
Possible cause➡Possible solution
The CD-R/RWs that are
playable on other
devices are not
playable on this unit.
The microcontroller in the unit operates abnormally due to noise or other
factors.
➡Press the reset switch. If there is no reset switch, unplug the
power cord and plug it again. In case the unit is still out of order,
consult the dealer.
The playability of some CD-R/RWs may depend on the combination of
media, recording software and recorder to be used even if these CDR/RWs are playable on other devices such as a PC.
➡Make CD-R/RWs in a different combination of media, recording
software and recorder after referring to the description about CDRs/RWs (➡page 24).
CQ-C1110W/C1100W
21
E
N
G
L
I
S
H
E
N
G
L
I
S
H
Troubleshooting (Continued)
❐ CD (Continued)
19
Problem
Possible cause ➡ Possible solution
Time is counted but no
sound comes out.
The first track of a mix mode disc was reproduced. (Mix mode is a
format in which data except music is recorded on the first track and
music data is recorded on other than the first track in a session.)
➡Play back music data recorded on other than the first track.
The disc has no error
but no playback is
made or the disc is
ejected automatically.
❐ Remote control unit
Trouble
Error display messages
❐ CD
Display
Possible cause ➡ Possible solution
Disc is dirty, or is upside down.
Condensation (dew).
➡Wait for a while before use.
Disc has scratches.
No operation by some cause.
Only for CQ-C1110W
After 5 seconds
Possible cause ➡ Possible solution
Battery polarities are reversed.
➡Insert the battery correctly.
¡Check the disc.
¡Load the disc again.
The disc is ejected automatically.
No disc is in the CD player.
➡ Insert disc into the CD player.
Wrong battery.
➡Check the battery.
Buttons are invalid for
operation.
20
Battery has run down.
➡Replace the battery.
Remote control unit is in the wrong direction.
➡Direct the remote control unit at sensor on the front panel.
The sensor is exposed to direct sunlight. (The remote control may
not be operable when the sensor is exposed to direct sunlight. In
such a case, the system is not faulty.)
➡Block off sunlight to the sensor.
Product servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest
authorized Panasonic Service center. The product should be serviced only by a qualified technician.
22
CQ-C1110W/C1100W
CQ-C1110W/C1100W
23
E
N
G
L
I
S
H
21
Maintenance
E
N
G
L
I
S
H
Specifications
❐ General
Care of the Unit
❐ Cleaning this unit
❐ Caution on cleaning
Use a dry, soft cloth to wipe.
Never use solvents such as benzine, thinner as
they may mar the surface of the unit.
Power supply:
Current consumption:
Maximum power output:
Tone adjustment range:
Suitable speaker impedance:
Preamp output voltage:
Output impedance:
Dimensions (W × H × D):
Weight:
Notes on Discs
Do not play any ordinary music CDs with labels other than
this one.
22
12 V DC (11 – 16 V), test voltage 14.4 V, negative ground
Less than 2.2 A (CD play mode; 0.5 W × 4 channels)
45 W × 4 channels (at 4 Ω)
Bass: ±12 dB at 100 Hz
Treble: ±12 dB at 10 kHz
4–8Ω
2.5 V (CD play mode; 1 kHz, 0 dB)
200 Ω
178 × 50 × 155 mm
1.4 kg
❐ FM stereo radio
How to hold the disc
• Do not touch the underside of the disc.
• Do not scratch the discs.
• Do not bend disc.
• When not in use, keep the disc in the case.
Frequency range:
Usable sensitivity:
50 dB quieting sensitivity:
Frequency response:
Alternate channel selectivity:
Stereo separation:
Image response ratio:
IF response ratio:
Signal/noise ratio:
Label side
Do not use irregular shaped discs.
Do not leave discs on the following places:
• Direct sunlight
• Near car heaters
• Dirty, dusty and damp areas
• Seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
❐ AM radio
Do not use irregular shaped discs.
<Correct>
<Wrong>
Do not attach any seals or labels to your discs.
Do not write on the disc label in a heavy pen or ballpoint
pen stroke.
Notes on CD-Rs/RWs
• You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives),
either due to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
• CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving
them inside a car for extended periods may damage them and make playback impossible.
• The unit may not successfully play back a CD-R/RW that was made by the combination of writing software, a
CD recorder (CD-R/RW drive) and a disc if they are incompatible one another.
• This player cannot play the CD-R/RW discs if the session is not closed.
• This player cannot play the CD-R/RW discs which contains other than CD-DA data.
• Be sure to observe the instructions of CD-R/RW disc for handling it.
24
CQ-C1110W/C1100W
87.5 – 108.0 MHz
11.0 dBf. (1.25 µV, 75 Ω)
15.2 dBf. (1.6 µV, 75 Ω)
30 Hz – 15 kHz (±3 dB)
75 dB
42 dB (at 1 kHz)
75 dB
100 dB
70 dB
Frequency range:
Usable sensitivity:
531 – 1 602 kHz
28 dBµV (25 µV, S/N 20 dB)
❐ CD player
Sampling frequency:
Error correction system:
Pick-up type:
Light source:
Wave length:
Frequency response:
Signal/noise ratio:
Total harmonic distortion:
Wow and flutter:
Channel separation:
8 times oversampling
Panasonic super decoding algorithm
Astigma 3-beam
Semiconductor laser
780 nm
20 Hz – 20 kHz (±1 dB)
96 dB
0.01 % (at 1 kHz)
Below measurable limits
75 dB
Note: Specifications and the design are subject to modification without notice due to improvements in technology.
CQ-C1110W/C1100W
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement